Professional Documents
Culture Documents
4ch SD Card User Manual
4ch SD Card User Manual
Cell/Whatsapp:17621808560
1. Accessories and interface
MDVR 1
Power cable 1
I/O cable 1
Cell/Whatsapp:17621808560
3G/4G antenna
1
(Optional)
GPS antenna
1
(Optional)
WiFi antenna 1
(Optional)
Remote control
1
(Optional)
Mouse
1
(Optional)
Cell/Whatsapp:17621808560
2. Panel introduction
Cell/Whatsapp:17621808560
3.Spec of voltage
Cell/Whatsapp:17621808560
4.Interfaces Definition
RX Blank
TX Blank
Cell/Whatsapp:17621808560
12V 12V power out
Pls note:
1)8V—36V,Otherwise mdvr may be damaged
2)After connecting the wires, pay attention to the insulation
Cell/Whatsapp:17621808560
between the power wires to prevent the power wires from short-circuiting
and burning the battery.
3 ) The yellow wire must be connected to the ignition wire,
otherwise the device will not support delayed shutdown and the final
video will be lost.
4)For installation, the positive and negative must be taken directly
from the battery. The ground wire will generate negative pulses
and interfere with the normal operation of the host. The diameter
of the power cord used for the positive and negative poles must
be Φ1.5mm or more.
5 . User Login
Cell/Whatsapp:17621808560
6. Main Menu
Right click the mouse, select “Main Menu” to start setup in the menu, see as
following:
“Main Menu” is the primary menu of the system setup and control, see as
following:
Cell/Whatsapp:17621808560
7. Record
Cell/Whatsapp:17621808560
〈SD Card Record〉:Pls enable SD (Format SD Card when reboot mdvr)
〈Channel〉:Select 1, 2, 3, 4 and all
〈Redundancy〉:can support dual SD card record at same time;
〈Length〉:Record packaging time, Default 30mins
〈PreRec〉:Set pre-record seconds
〈Mode〉:Schedule: power on, automatic recording
Manual:Manually start recording
Stop:Turn off recording
〈Week〉:Select Monday to Sunday or All
〈Period〉:period1 to period4 :24hours optional
〈Channel〉:Select 1 to 4 or All;
〈Compression〉:H.265X and H.265 optional,H.265X mean upgrade base on
H.264
〈Resolution〉:Support 1080P\960P\720P\D1\CIF;
〈Frame Rate〉:1080P, MAX 18PPS;
〈Bit Rate Type〉:default VBR,According to the image changes, the stream
will change;
〈Quality〉:Highest,higher,high,low,lower,lowest;
〈Bit Rate〉:Dynamic,cann’t be set
〈I Frame Interval〉:No need set;
Cell/Whatsapp:17621808560
〈Video /Audio 〉:closed or opened ;
Cell/Whatsapp:17621808560
7.3 Playback
Play button
Next file
Cell/Whatsapp:17621808560
7.4 Backup
Cell/Whatsapp:17621808560
〈Channel〉:1,2, 3,4 optional
Car info, channel, Time, GPS Optional
Cell/Whatsapp:17621808560
8. General
General including Guide time, system, power settings, car info, channel
settings,output Adjust, preview overlay
Cell/Whatsapp:17621808560
8.1 Guide Time
Cell/Whatsapp:17621808560
8.2 System
Cell/Whatsapp:17621808560
8.3 Power Settings
Cell/Whatsapp:17621808560
8.4 Car Info
Cell/Whatsapp:17621808560
8.5 Channel Settings
〈Channel 1〉Mirro,Overt,Ruler
〈Channel 2〉Mirro,Overt,Ruler
〈Channel 3〉Mirro,Overt,Ruler
〈Channel 4〉Mirro,Overt,Ruler
Cell/Whatsapp:17621808560
8.6 Output Adjust
Cell/Whatsapp:17621808560
8.7 Preview overlay
〈Car info 〉
〈Channel〉
〈Time〉:
〈GPS〉:
〈Speed〉:
Cell/Whatsapp:17621808560
9. Net Service
Cell/Whatsapp:17621808560
9.1 DAS
〈Enable〉
〈Serial number〉:
〈Server IP〉:
〈Server Port〉:
〈User name〉:admin
〈Password〉:
Cell/Whatsapp:17621808560
9.2 Network
Cell/Whatsapp:17621808560
9.3 4G Network
4G Network
Enable
Type: If 4G, pls select 4G
Wireless AP: blank
Dial number: blank
User name:blank
Password:blank
IP: blank
Cell/Whatsapp:17621808560
9.4 WIFI
Cell/Whatsapp:17621808560
9.5 CMS Set
Cell/Whatsapp:17621808560
9.6 Network Status
Cell/Whatsapp:17621808560
10. Alarm
Alarm setup interface includes the setting related to all alarm types, such as
Video Loss, I/O alarm, Speed Alarm, G-sensor,Abnormality,Motion detect.
Cell/Whatsapp:17621808560
10.1 Video Loss
〈Enable〉:Set enable. When video is lost, will trigger the alarm output and
display the full screen of the channel
〈Alarm out〉:When video is lost, alarm 1 or alarm 2 output can be set.
〈Tour〉:When the video is lost, any channel can be configured to display in
full screen;
〈Out delay〉:Alarm and polling output time;
〈Buzzer〉:When the alarm is triggered, the main board buzzer will sound;
(this function has no effect);
Cell/Whatsapp:17621808560
10.2 Alarm Input
Cell/Whatsapp:17621808560
10.3 Speed alarm
〈H-Speed〉:Turn on or off, you can set the maximum speed, the default is
80KM/H;
〈L-Speed〉:Turn On or off; you can set the minimum speed, the default is
0KM/H;
〈Alarm Out〉:When the speed reaches 80KM/H, alarm 1 or alarm 2 output is
triggered;
〈Video〉:When the speed reaches 80KM/H, trigger the corresponding video
recording;
〈OSD〉:When the speed reaches 80KM/H, text can be displayed on the
screen;
〈 Tour 〉: When the speed reaches 80KM/H, trigger the corresponding
full-screen display;
〈MD Interva〉:Effective time between overspeed alarm triggering;
Cell/Whatsapp:17621808560
〈PreRec〉:Trigger alarm recording pre-recording time;
〈Outdelay〉:Trigger alarm output time;
〈PostRec〉:After triggering the alarm and stopping, the recording delay time;
〈Buzzer〉:When the alarm is triggered, the buzzer sounds;
10.4 G-sensor
Cell/Whatsapp:17621808560
〈Alarmout〉:Trigger alarm 1 or alarm 2 output;
〈Outdelay〉:Alarm output time;
〈Record Channel〉:Alarm trigger and recording channel;
〈Tour〉:Alarm trigger channel full screen display;
〈Time inter〉:Alarm signal trigger effective interval time;
〈Prerec〉:Trigger recording pre-recording time;
〈PostRec〉:Trigger recording delay time;
〈Buzzer〉:The buzzer sounds after the alarm is trigger;(default is not
enable )
10.5 Abnormality
Cell/Whatsapp:17621808560
10.6 Motion Detect
Cell/Whatsapp:17621808560
〈Snapshot〉:channel 1,2,3,4 optional
〈PTZ Activation〉:channel 1,2,3,4 optional
〈PostRec〉:channel 1,2,3,4 optional
Show message, send Email, Write Log, FTP upload, Mobile reported Optional
〈Account〉: can set user, Modify user, Modify group, Modify pwd, add user,
add group, delete user, Delete group, Update, Account security
〈Device Info〉:can set audio in channels, alarm in channels, alarm out
channels, remote control type, Maximum playback large, Default playback
large, Enable buzzer, Enable RS232, Enable PTZ;Maintain, Debug Mode.
〈 RS232 〉: Set function like GPS, General, InteractCmd , Ranging,
Transparent ;can set Baudrate, Bate Bits, Stop Bits, Parity.
Cell/Whatsapp:17621808560
12. Device Maintain
〈Account〉: can set user, Modify user, Modify group, Modify pwd, add user,
add group, delete user, Delete group, Update, Account security
〈Device Info〉:can set audio in channels, alarm in channels, alarm out
channels, remote control type, Maximum playback large, Default playback
large, Enable buzzer, Enable RS232, Enable PTZ;Maintain, Debug Mode.
〈 RS232 〉: Set function like GPS, General, InteractCmd , Ranging,
Transparent ;can set Baudrate, Bate Bits, Stop Bits, Parity.
Cell/Whatsapp:17621808560
13. Device Maintain
〈Upgrade〉:Upgrade the device, Insert pen driver into USB port, Select the
upgrade file and upgrade the device
Cell/Whatsapp:17621808560
14. IO interface Definition
1 2 3 4 5 6
7 8 9 10 11 12
Cell/Whatsapp:17621808560
方向灯
+24V
方向
Connect
MDVR
Sensor input
The alarm output is all level output, and theline
driveSensor
capacity is 200mA. If you
input line
want to drive a device with a relatively large power, you must connect an
external relay.
Cell/Whatsapp:17621808560