Professional Documents
Culture Documents
Loctite Liofol La2615 Mhs La5000-En
Loctite Liofol La2615 Mhs La5000-En
Application Areas:
LOCTITE LIOFOL LA 2615 MHS / LA 5000 exhibits good Compliance with food packaging regulations:
bond strength with a variety of laminates. The product Under specific conditions LOCTITE LIOFOL LA 2615 MHS /
is compatible with slip additives and is particularly suited for LA 5000 is suitable for the manufacture of food packaging
the lamination of EVA-Copolymerfilms. At transparent materials under the applicable FDA, EC-provisions and/or
substrates, laminates produced with LOCTITE LIOFOL LA BfR recommendations.
2615 MHS / LA 5000 are resistant to pasteurising, boiling LOCTITE LIOFOL LA 2615 MHS / LA 5000 contains
and sterilisation. aromatic isocyanates. We therefore recommend migration
testing of the fully cured material under conditions of use,
particularly with high temperature applications, to
Suitable Films: demonstrate compliance with the limits for primary aromatic
● Aluminum Foil amines.
● treated polyethylene A food contact statement with further details is available on
● treated Polypropylene request.
● Polyester The responsibility for compliance with the specific conditions
● Polyamide is with the converter and not with the adhesive supplier.
● Metallised film
● Cellophane DIRECTIONS OF USE
Preliminary Statement:
Prior to application it is necessary to read the Safety Data
Product Properties: Sheet for information about precautionary measures and
When being run at 30 to 35 % solids, LOCTITE LIOFOL LA safety recommendations. Also, for chemical products exempt
2615 MHS / LA 5000 provides excellent laminating from compulsory labeling, the relevant precautions should
properties. Application at higher solids is possible on suitable always be observed. Please also refer to the local safety
coating units and adjusted working conditions. instructions and contact Henkel for analytical support.
For laminates exposed to high temperatures (boiling,
pasteurising, sterilisation) we recommend to increase the mix
ratio Base:Hardener to 9.4:2 by weight. The Protective Measures:
cured polyurethane film is transparent, odourless, elastic and As the adhesive contains polyisocyanates any contact with
age-resistant. skin should be avoided. If skin gets in contact with LOCTITE
LIOFOL LA 2615 MHS / LA 5000 please remove the
adhesive immediately. Safety regulations with regard to
handling of isocyanates have to be followed as per the guide
lines issued by the International Isocyanates Institute. The
maximum concentration of solvents in the air
(TLV-value) has to be observed.
TDS LOCTITE LIOFOL LA 2615 MHS / Hardener LA 5000, April-2013
Dilution: STORAGE
Suitable solvents are ethyl acetate, acetone and Once opened, containers have to be closed tightly again and
Methylethylketone provided that the water content does not the material should be consumed within a short period.
exceed 300 ppm. When stored in a dry and cool place in the original unopened
Do not use aromatic or alcoholic solvents. containers storage life is as follows.
Shelf life:
Dilution Table: LOCTITE LIOFOL LA 2615 MHS, months: 12
In order to obtain a certain solids content, the following LOCTITE LIOFOL LA 5000, months: 9
quantities of solvent have to be added. Recommended Storage Temperature, °C -30 to +25
The Ford/DIN cup (4 mm/20 °C) viscosities are based on an
average viscosity of LOCTITE LIOFOL LA 2615 MHS / LA
5000. Classification:
Please refer to the corresponding safety data sheets for
Base details on:
LOCTITE Hardener Ethyl Solid Viscosity Hazardous Information
LIOFOL LA LA 5000 Acetate Content (sec.) Transport Regulations
2615 MHS
Safety Regulations
25 kg 4.55 kg 19.70 kg 45 % 21 - 23
25 kg 4.55 kg 25.86 kg 40 % 17 - 18 ADDITIONAL INFORMATION
25 kg 4.55 kg 33.77 kg 35 % 15 - 16 Film Requirements:
Film additives - particularly slip agent content in LDPE,
25 kg 4.55 kg 44.33 kg 30 % 13 - 14
MDPE and CPP films - packed goods, printing inks,
pre-treatment and coating of films are of significant
Mixing: importance to the intended use of the laminates and may
LOCTITE LIOFOL LA 2615 MHS has to be diluted under affect the performance properties either straight away or
stirring with corresponding solvent to the desired later. Therefore, practical laminating tests as well as
application solids. checks on the laminates are necessary before going
Then the correct amount of Hardener LA 5000 has to be into full scale production. Further detailed information
added under agitation. can be obtained from our "Technical Guide Line for
Laminating with Liofol Laminating Adhesives".
Pot Life:
The Ready-for-use adhesive (30 to 35%) in closed Product Range:
containers has a working time of about 2days without Apart from LOCTITE LIOFOL LA 2615 MHS / LA 5000 we
substantial viscosity increase. Overage adhesive mixtures as can offer the following products for the manufacture of
well as old adhesive in the glue pot affect the quality of the film/foil laminates:
laminates adversely. ● Solventbased, solventless and waterbased laminating
adhesives for flexible packaging and special
Application: applications
LOCTITE LIOFOL LA 2615 MHS / LA 5000 can be applied ● Coldseal Adhesives
with all dry laminating units with smooth or gravure rollers. ● Heatseal Coatings
● Primer for Extrusion and PVDC-coating
Application Weight: ● Adhesives for High Gloss Lamination
The application weight may range from 2.5 to 3.5 g/m² dry ● Special Cleaning agents
depending on the film or foil combination and the intended To obtain product specifications please ask for the relevant
use of the laminate. For films containing slip additives we technical datasheets.
recommend the higher application weight. Heat resistant and
deep draw laminates with thick films require a coating weight
of up to 5 g/m² dry. For printed laminates the weight has to
be adjusted to higher weights accordingly, it should be
approx. 1 g/m² higher than for unprinted films.
Working Conditions:
High laminating temperatures together with a high line
pressure of the calander improve the bond strength and
optical appearance of the laminates.
Curing:
Manufacture of triplex laminates is possible 2 to 4 hours after
duplex production. The laminates may be slit after 4 to 6
hours. Complete curing i. e. total resistance to severe
environments will be achieved after 7 to 14 days of storage
at room temperature depending on film combination and
intended use of the laminates. Processing of pouches should
not start before the full curing.
TDS LOCTITE LIOFOL LA 2615 MHS / Hardener LA 5000, April-2013
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The
product can have a variety of different applications as well as differing
application and working conditions in your environment that are beyond our
control. Henkel is, therefore, not liable for the suitability of our product for the
production processes and conditions in respect of which you use them, as
well as the intended applications and results. We strongly recommend that
you carry out your own prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any
other written or oral recommendation(s) regarding the concerned product is
excluded, except if otherwise explicitly agreed and except in relation to
death or personal injury caused by our negligence and any liability under any
applicable mandatory product liability law.
Trademark usage
Except as otherwise noted, all trademarks in this document are trademarks
of Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark
registered in the U.S. Patent and Trademark Office.
Reference 0.0