Professional Documents
Culture Documents
Hsu09lek03 Annexe 3
Hsu09lek03 Annexe 3
OPERATION MANUAL
HSU-07LEK03
HSU-09LEK03
HSU-12LEK03
HSU-09LEK13
HSU-12LEK13
HSU-07HEK03
HSU-09HEK03
HSU-12HEK03
Please read this operation manual before using the air conditioner.
0010518786
Cooling o o
Maximum:D.B/W.B 43 C/26 C
Outdoor Minimum:D.B o
18 C
Maximum:D.B 27oC
Indoor o
Minimum: D.B 15 C
Heating o o
Outdoor Maximum:D.B/W.B 27 C/18 C
Minimum:D.B -7oC
Installation
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.
lnstallation in a inadequate place may cause accidents. Do not install in the following place.
CAUTION
Connect the earth Do not install in the Do not get the unit Check proper
cable. place where there is exposed to vapor installation of the
any possibility of or oil steam. drainage securely
inflammable gas
leakage around the
unit.
earthing
STRICT
PROHIBITION PROHIBITION ENFORCEMENT
OFF STRICT
ENFORCEMENT
Connect power supply cord Use the proper voltage Do not use power supply cord
to the outlet completely extended or connected in halfway
STRICT STRICT
ENFORCEMENT PROHIBITION
ENFORCEMENT
Do not use power supply cord Take care not to damage Do not insert objects into the air
in a bundle. the power supply cord. inlet or outlet.
Do not start or stop the Do not channel the air flow directly Do not try to repair or reconstruct
operation by disconnecting at people, especially at infants or by yourself.
the power supply cord and so on. the aged.
PROHIBITION PROHIBITION
CAUTION
Do not use for the purpose of storage of Take fresh air occasionally especially Do not operate the switch with
food, art work, precise equipment, when gas appliance is running at the wet hand.
breeding, or cultivation. same time.
STRICT
PROHIBITION ENFORCEMENT PROHIBITION
Do not install the unit near a fireplace Check good condition of the Do not pour water onto the unit
or other heating apparatus. installation stand for cleaning
Actual inlet grille may vary from the one shown in the manual according to
the product purchased
Outdoor Unit
HSU-09LEK03 HSU-09LEK13
HSU-12LEK03 HSU-12LEK13
HSU-09HEK03 HSU-07LEK03
HSU-12HEK03 HSU-07HEK03
4. SLEEP display
10
1 5. LOCK display
6 6. SIGNAL SENDING
2
7
7. TIMER OFF display
5 8
8. TIMER ON display
9
3 9. CLOCK display
4
23 HEALTH ON/OFF
10. TEMP display
24
11
11. POWER ON/OFF
13 Used for unit start and stop.
FAN
18 12. MODE
Used to select AUTO run, COOL, DRYˈ
MODE
HEAT and FAN operation
13. FAN
SWING 15
Used to select fan speed LO, MED, HI, AUTO
20
TIMER
14. HOUR
12 Used to set clock and timer setting.
21
CLOCK 14 15. SWING
Used to set auto fan direction.
19 SET SLEEP 16
16. SLEEP
17 22 Used to select sleep mode.
LOCK RESET
17. LOCK
Used to lock buttons and LCD
display.
18. TEMP.SETTING
Used to select your desired temp.
19. SET
Used to confirm timer and clock settings.
20. TIMER
Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF
21. CLOCK
Used to set correct time
1. Mode display 22. RESET
AUTO Used to reset the controller back to
COOL normal condition.
DRY 23. HEALTH display
HEAT 24. HEALTH
FAN Used to operate the healthy function.
2. SWING display
AUTO LO MED HI
3. FAN SPEED display
Clock set
When unit is started for the first time and after replacing batteries in remote controller,
clock should be adjusted as follows:
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press will increase or decrease 1min. If the
button is kept depressed, time will change quickly.
After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock
starts working.
NOTE: Cooling only unit do not have displays and functions related with heating
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.
Clock set
When unit is started for the first time and after replacing batteries in remote controller,
clock should be adjusted as follows:
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press will increase or decrease 1min. If the
button is kept depressed, time will change quickly.
After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock
starts working.
NOTE: Cooling only unit do not have displays and functions related with heating
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.
HEA
LTH
ON/
OFF
FAN
MOD
E
SW
TIM
ING
ER
CLO
CK
SET
When electronic-started type fluorescent lamp or change-over
LOC
K
SLE
EP
RES
ET
type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receivering the signals
so the distance to the indoor unit should be shorter.
Note: When sudden power failure happens during unit operation in power failure resume mode,
if the air conditioner is not desired for use in a long period, please shut off the power
supply in case that the unit automatically resume operation when power is re-supplied,
or press ON/OFF to turn off the unit when power resumes.
AUTO LO MED HI
Note:
1. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according
to room temperature.
2.In DRY mode, when room temperature becomes lower than temp.setting+2oC,
unit will run intermittently at LOW speed regardless of FAN setting.
3. In FAN operation mode, the unit will not operate in COOL mode but only in FAN mode ,
AUTO is not available in FAN mode.And temp.setting is disabled.
In FAN mode,SLEEP operation is not available.
4.In HE AT mode, warm air will blow out after a short period of the time due to cold-draft
prevention function.When FAN is set to AUTO, the air conditioner automatically adjusts
the fan speed according to room temperature.
5.Remote controller can memorize each operation status. When starting it next time,
just press ON/OFF button and unit will run in previous status.
CLOCK
SET SLEEP
2.Up and down air flow direction(Use remote controller)
LOCK RESET
Cautions:
Do not try to adjust the flap by hand.
When adjusting the flap by hand,turn off the unit ,and use the remote controller to restart the unit.
When humidity is high,condensate water might occur at air outlet if all vertical louvers are
adjusted to left or right.
It is advisable not to keep horizontal flap at downward position for a long time in COOLor DRY
mode ,otherwise, condensate water might. occur.
Hints
As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more
helpful for a better air circulation.
10
TIMER ON/OFF
(1)After unit start, select your desired operation mode.
Operation mode will be displayed on LCD.
Power indicator on indoor unit lights up.
Press HOUR / button. CLOCK
Every time the button is pressed, time increases 10 min. SET SLEEP
11
(3)Time setting for TIMER ON FAN
LOCK RESET
Time will be shown on LCD.
It can be adjusted within 24 hours.
AM refers to morning and PM to afternoon
(4) Time confirming for TIMER ON
After time setting, press TIMER button to confirm.
"ON" stops blinking, While "OFF" starts blinking.
Time displayed: Unit starts at x hour x min.
12
1.Unit start
Press the ON/OFF switch
HEALTH ON/OFF
controller.
SWING
TIMER
CLOCK
SET SLEEP
RESET
NOTE: If the unit which you purchased has healthy function,follow it.If not,please ignore.
13
1 hr
Decreases 2OC
3 hrs
3 hrs Rises 1OC
SLEEP SLEEP
ON/OFF
operation starts operation stops
In HEAT mode
FAN
MODE
3. In AUTO mode
SWING
The unit operates in corresponding sleep
mode adapted to the automatically selected
TIMER
operation mode.
CLOCK
SET SLEEP
4. In FAN mode
LOCK RESET
It has no SLEEP function.
5. When quiet sleeping function is set to 8 hours,
the quiet sleeping time can not be adjusted.
When TIMER function is set , the quiet sleeping
function can't be set up .After the sleeping function
is set up,if user resets TIMER function, the sleeping
function will be cancelled; the machine will be in the
state of timing-on,if the two modes are set up at the
Operation Mode same time ,either of their operation time is ended
first ,the unit will stop automatically,and the other
1. In COOL,DRY mode mode will be cancelled.
1 hours after SLEEP mode starts, temp. will
become 1OC higher than temp. setting. After
another 1 hours, temp. rises by 1OC further. Power Failure Resume Function
The unit will run for further 6 hours then stops.
Temp. is higher than temp. setting so that room If the unit is started for the first time, the
temperature won't be too Iow for your sleep. compressor will not start running unless 3
minutes have elapsed. When the power
resumes after power failure, the unit will run
SLEEP operation starts SLEEP operation stops automatically, and 3 minutes later the
Approx.6hrs compressor starts running.
4
Emergency Operation:
Use this operation only when the remote controller is defective or lost,and with
function of emergency running, air conditoner can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "sound is
heard once, which means the start of this operation.
When power switch is turning on for the first time and emergency operation starts,
the unit will run automatically in the following modes:
emergency
Room Designated Timer Fan Operation operation switch
temperature temperature mode speed mode
P
i
o o
Above 23 C 26 C No AUTO COOL
o o
Below 23 C 23 C No AUTO HEAT
Test operation:
Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room
o
temperature is below 16 C, do not use it in the
normal operation.
test operation
Continue to press the test operation switch for more switch
5
Proper
temperature
OFF
16
O O
Gasoline,benzine, thinner or cleanser may Hot water over 40 C(104 F) may cause
damage the coating of the unit. discoloring or deformation.
17
Mist or steam are blown out. During COOL or DRY operation, indoor unit
may blow out mist. This is due to the sudden
cooling of indoor air.