Professional Documents
Culture Documents
GEARBOX
m
DIFFERENTIAL
13.106
+ D===:;:::==:{] 5.096
3.876
13.1 06
~A
T
Differential internal housinq bearina conical roller bearings
-0
CO)
Adiustment of bearina ore-ioadina by shims
mm 1.70-2.89
Thickness of shims (~ 007)
Interference to obtain
exact bearing pre- mm
loading
~.~
0
Clearance
planet/satellite gears
Adjustment of clearance
between planet/satellite No adjustment
gears
0 257
19.80-20.10
18.55
allowed 18.20
allowed
~ Brake servo
REAR BRAKES
0 240
10.80-11.10
~ 10.10
allowed 9.20
"1
allowed 1,5
34
0.30
0.25
24 Print n° 506.586/14
Fiat barchetta Technical Data
2000 range Steering
Make
~-
~
'-./ '"'--' 2.45
-=--f-=-
no. of turns lock to lock
+
125 mm
Ratio
rack travel
.,r- -I-
/' L~ -I"
/ Minimum
I \ m 10.5
\ turning circle
I~ ~ .1
a1
t;-. outer
. wheel
(XI 30°:f:30'
Inner
<X2 32°45':i:30'
wheel
Steering angle
Steering column
with 2 universal joints
rim 6Jx15" - 37
camber (**)
I~ -1 °::1:30'
Front
caster (**)
~ 3°:1:30'
wheel offset
O'
fro nt (£.)
fUV
I
Rear toe in (**) -0.7-3.3 mm
suspension
wheel thrust angle
O'
rear(.)
(*) With tyres inflated to the recommended pressure and vehicle in running order
(**) Angles cannot be adjusted
(£.) Angular values, which cannot be adjusted, used for the correct alignment of the vehicle
Height of spring
under 321-341 daN mm 164
a load of:
Anti-roll bar
Rear suspension independent with spheroid cast iron track control arms.
Coil springs and gas shock absorbers with vulcanized bushes.
Anti-roll torsion bar. Rigid H-shaped auxiliary frame consisting of a transverse tubular element and two
pressed side members connected to each other.
Coil springs
Number of coils 4
Height of spring
under 270-290 daN mm 159
a load of:
The springs are divided into two categories,
identifiable by a mark:
yellow (1) for having a height
those under a 284 daN > 159
of mm
load of:
green (1) for having a height
those under a 284 daN
of mm
~ 159
load of:
(1) When fitting, match springs of the same type.
Shock absorbers
M. MarelliA1151-14V-38/65A
ALTERNATOR
M. MarelliA127IR-14V-55/100A(8)
STARTER MOTOR
NOTE When overhauling it is not necessaryto undercut the insulator between the commutator bars.
30 Print ff 506.586/14
Fiat barchetta Technical Data
2000 range Electrical equipment:recharging
ALTERNATOR
Make
M. Marelli M. Marelli
A1151-14V-38/65A A127IR-14-55j100A (8)
(*) Data obtained at a temperature of 20.C. (8) For vehicle with air conditioning
Test curret A
PENCIL COIL
Type CM 11-201
RPMSENSOR
Make and type HITACHI GE 110492
DETONATION SENSOR
ENGINE ADVANCE
SPARK PLUGS
NGK BKR6EZ
Make and type
Chamoion RC10YCC
Thread M14x1.25
Tightening
torques
DESCRIPTION Thread
daNm
ENGINE
Flywheel side cover fixing, bolt with flat washer M6x16 0.9
M10x1.25 1.2
Tapered,threaded plug
M16x1.5 1.6
Tightening
torques
DESCRIPTION Thread
daNm
Coil cover fixing, bolt with unlosable, flat washer M6x30 0.9
M8x25
Exhaustmanifold retaining bracket fixing, bolt 2.5
M8x18
M8x55
Crankshaft pulley fixing, bolt with Belleville washer 2.5
M8x32
Tightening
torques
DESCRIPTION Thread
daNm
M 8x65 2.5
Driveshaft support fixing, flanged bolt
M10x1.25 5
Tightening
torques
DESCRIPTION Thread
daNm
ENGINE EXHAUST
40 Print n° 506.586/14
Fiat barchetta Technical Data
2000 range Tightening torque
00.
Tightening
torques
DESCRIPTION Thread
daNm
GEARBOX
Flexible mounting to gearbox fixing, bolt with normal
M8 2.7
flange
Tightening
torques
DESCRIPTION Thread
daNm
BRAKING SYSTEM
Male connector for pipes with flared ends securing M10x1 1.8
rigid pipe to hose on rear axle
42 Print ff 506.586/14
Fiat barchetta Technical Data
2000 range Tightening torque
STEERING
Connector for oil supply pipe from power assisted M16x1.5 3.6
steering pump
M16x1.5 5
M8 3
M10x1.25 4
M12x1.25 5.5
Tightening
torques
DESCRIPTION Thread
daNm
Anti-roll bar to track control arm fixing, bolt with nor- M8 3.5
mal flange
REAR SUSPENSION
Wheel bolt
M12x1.25 8.6
steel rim
44 Print n° 506.586/14
Fiat barchetta Technical Data
2000 range Tightening torque
Wheel bolt
M12x1.25 8.6
alloy
Upper shock absorber fixing, bolt with normal flange M10x1.25 6.2
Hub to track control arm fixing, nut with metal insert M22x1.5 28
M8
M10x1.25
M10x1.25
Tightening
torques
DESCRIPTION Thread
daNm
AUXILIARY UNITS
FUEL CIRCUIT
BODYWORK
46 Print ff 506.586/14
Fiat barchetta Technical Data
2000 range Tighteningtorque
Tightening
torques
DESCRIPTION Thread
daNm
ELECTRICAL EOUIPrVlENT