Professional Documents
Culture Documents
Data sheet
102807_en_10 © PHOENIX CONTACT 2022-03-30
1 Description
The narrow 6.2 mm MINI MCR-SL-R-UI... potiposition Features
transducer converts potentiometer positions into a standard
– Configurable potipostion transducer
analog signal on a percentage basis. If the potentiometer
range cannot be utilized to the full, an externally accessible – Output signal range can be configured using a DIP
slide switch is used to set the upper and lower potentiometer switch
final values. The output signal of between 0% ... 100% is – Screw connection available
based on this set final value.
The DIP switches are accessible on the side of the housing
and allow the following parameters to be configured:
– output signal,
– automatic potentiometer detection,
– wire-break detection slider as well as
– error indication type.
Power (19.2 V DC ... 30 V DC) can either be supplied via
the connection terminal blocks of the modules or in
conjunction with the DIN rail connector.
This document is valid for the products listed in the “Ordering data”.
MINI MCR-SL-R-UI
2 Table of contents
1 Description .............................................................................................................................. 1
2 Table of contents ..................................................................................................................... 2
3 Ordering data .......................................................................................................................... 3
4 Technical data ......................................................................................................................... 4
5 Safety regulations and installation notes.................................................................................. 6
5.1 Installation notes ................................................................................................................. 6
5.2 UL notes............................................................................................................................ 6
6 Installation ............................................................................................................................... 7
6.1 Connection notes ................................................................................................................ 7
6.2 Structure ........................................................................................................................... 7
6.3 Block diagram ..................................................................................................................... 7
6.4 Power supply ...................................................................................................................... 8
6.5 Mounting ........................................................................................................................... 8
6.6 Connection of the cables ....................................................................................................... 8
7 Configuration ........................................................................................................................... 9
7.1 Configuration tables ........................................................................................................... 10
3 Ordering data
4 Technical data
Input
Potentiometer resistance range 100 Ω ... 100 kΩ
Reference voltage source < 3.6 V
Output
Number of outputs 1
Voltage output signal 0 V ... 5 V
1 V ... 5 V
0 V ... 10 V
10 V ... 0 V
Max. voltage output signal 12.5 V
Short-circuit current approx. 10 mA
Current output signal 0 mA ... 20 mA
4 mA ... 20 mA
20 mA ... 0 mA
20 mA ... 4 mA
Max. current output signal 23 mA
Non-load voltage approx. 12.5 V
Load/output load voltage output > 10 kΩ
Ripple < 20 mVPP (at 500 Ω)
Load/output load current output < 500 Ω (20 mA)
Behavior in the event of a sensor error 0 % ... 105 % (configurable)
Supply
Nominal supply voltage 24 V DC
Supply voltage range 19.2 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2
TBUS-2 1,5/5-ST-3,81 GN, Item No. 2869728) can be used to
bridge the supply voltage. It can be snapped onto a 35 mm DIN
rail according to EN 60715))
Typical current consumption < 25 mA (at 24 V DC)
Power consumption < 500 mW
General data
Maximum transmission error < 0.2 %
Temperature coefficient, typical < 0.02 %/K
Maximum temperature coefficient < 0.02 %/K
Step response (0–99%) < 30 ms
Electrical isolation Basic insulation according to EN 61010
Mounting position any
Degree of protection IP20
Rated insulation voltage 30 V AC
50 V DC
Test voltage, input/output/supply 1.5 kV (50 Hz, 1 min.)
Type of housing PBT
Connection data
Connection method Screw connection
Conductor cross section solid 0.2 mm² ... 2.5 mm²
Conductor cross section flexible 0.2 mm² ... 2.5 mm²
Conductor cross section AWG 26 ... 12
Stripping length 12 mm
Ambient conditions
Ambient temperature (operation) -20 °C ... 65 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C
Permissible humidity (operation) 5 % ... 95 % (non-condensing)
Maximum altitude for use above sea level ≤ 2000 m
Conformance/Approvals
CE
CE-compliant
UKCA
UKCA-compliant
UL, USA / Canada UL 508 Recognized
Class I, Div. 2, Groups A, B, C, D T4
Shipbuilding approval
DNV GL TAA000020N
Temperature B
Humidity B
Vibration B
EMC A
Enclosure Required protection according to the Rules shall be provided
upon installation on board
6 Installation
6.1 Connection notes 6.3 Block diagram
Figure 2 Block diagram
NOTE: electrostatic discharge!
The device contains components that can be Sensor / Field IN OUT PLC / DCS
3 2
5 4 +24V
GND 3
Warning – Do n ot seperate
erg
erm L–
y
an R–U5
, G R – S 4 09
6
I
1
lomb I MC 28
5 B IN o.:
M .–N
when energized
82 dr
32 2 Or
ce ...0
V
1
du , 10
ns mA
ON Tra
.(4)0
tor
6 S2 FF
O
sitio
Po kǥ 0(1)...
5V,
n In
0
d
...1 0V,
20..
ica
Sen
sor
/ Fie
ld
00 A,
0...1 ..20mDC 4°...+
(4). 0V / –
IN: : 0 ,2...3 5°C
149
°F
10
T 9 6
OU 1 0°...+
1
+
–2 IN 1
2
Tamb IN 2
-
,I
TU
S OU + 3
/ DC 5 active IN 3
PLC +
D2
5
GN -
G G cX
II 3 A II C T4
6 D3 4
iv e - GN
pass 6
Ex n
V
+24
7
+
www.phoenixcontact.com
D2 D2
GN GN
- 8 V
+24
ON 8
S1
7 F
OF 1
11
Ser
ial N
o.
9
8
1 Input: Potentiometer
2 Cover
3 Press/slide button for teach-in
4 Diagnostics LED
5 Groove for ZBF 6 Zack marker strip
6 Output: Standard signals
7 Supply voltage
8 Connection for DIN rail connector
9 DIP switch S1
10 DIP switch S2
11 Universal snap-on foot for EN DIN rails
B 12 mm
A 0,5-0,6 Nm
5-7 lb In
• Insert the wire into the corresponding connection
terminal block.
• Use a screwdriver to tighten the screw in the opening
above the connection terminal block.
7 Configuration
If the modules are not configured (all DIP switches set to
position 0), the module does not have a defined function
until the DIP switches have been set.
Use the DIP switch to specify the output signal range,
potentiometer detection/wire-break detection, and error
evaluation.
Activate automatic potentiometer detection to obtain
optimum measurement results.
You can use the S2 DIP switch to select the voltage and
current output.
Figure 5 Location of the DIP switches
UI
-R- 9 5
-SL 0 cer
CR 64 du
I M : 28 rans V
MIN.-No. - T .10
, 0..
Ord tance V
on sis ...5 k
Re k , 0(1) 10
S2 off 1 00 mA U . °F
0...1)...20 / , 1min.+149
ge: 0(4 500 0 Hz -4°.. S2
ran I kV , 5°C /
as. 1,5 °..+65
Met:
Ou d: age: -20
1
Loat volt mp.:
Tesb. Te
2
www.interface.phoenixcontact.com
Am 5 T
OU
3
,I
t U 6 4
Ou IN
1
GN
D 7+ ER
W
PO
C
VD 8-
.30
,2.. 2
19 D
GN
8
on S1
off 1
XX
XX
XX
XX
o.
l N
S eria
S1
0 1 2 3 4 5 6 7 8 9 10 k
0% 100 %
0V 2V 8V 10 V
0% 100 %
0V 10 V
10 Connection/application example
Positioning table with positioner/controller
Figure 7 Connection example
Lifting platform
M
Actuator motor ACTUAL TARGET
Potentiometer 0...10 V 0...10 V
Controller
1 OUT 5
Control system
2 GND1 6
3 UB + 7
4 GND2 8
Mains voltage
102807_en_10 PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany 12/12
phoenixcontact.com