Professional Documents
Culture Documents
This product is designed only supporting proximity card. It works as Operating Humidity Power off, press and hold the "exit button", power on. There will be
0% ~ +98%RH
Metal Waterproof Standalone Access Control/Reader standalone access control, supporting up to 10,000 Mifare card
holders. Dimension 110 x 76 x22(mm)
two "beep", release the button to read “Master Add Card” and
“Master Delete Card”. There will be one long “beep”. Enter into
With wiegand 34 bits input & output, it can be also used as controller Net weight 435g standby mode. Factory default Settings and add master cards
INTRODUCTION or external reader. Gross weight 505g successfully.
It is operated by remote control. Also, the Manager Card make it Note: Factory default is cannot delete the user data. If you do not
convenient and faster to add/delete users.
1 It adopts the Atmel MCU, however, the User Data stored in
independent chip. Once the device is damaged deliberately,
want to add master cards, power on, press the exit button
for 10 second and then release.
the User Data chip can be disassembled quickly and installed in the
same model product. Packing List
Number Name Quantity Note Simplified Instruction
1 Access control 1 INSTALLATION Function Description Operation
Features and Benefits 2 User manual 1 1. Remove the back cover from the unit. (Admin Code) #
Metal case, anti-vandal 3 Rubber stopper 2 6*25mm
2. Drill holes on the wall for the screw and one hole for the cable. *then you can do the programming
3. Knock the supply rubber bungs to the screw holes. Enter the Programming Mode
INSTALLATION Waterproof, conforms to IP67 4 Screw 2 KA4*25mm 4. Fix the back cover firmly on the wall with 4 flat head screws.
(777777 is the factory
Operated by remote control and manger cards default master code)
5 Safety screw driver 1 5. Tread the cable through the cable hole.
Large user capacity: 10,000 card holders 6. Attach the unit to the back cover. 0 - New Code - # - Repeat the
40mm
Master Cards Usage
Exit from the Programming Mode
*
How to release the door
Specifications
80mm
Using Master cards to add and delete card users Card User Read Card
OPERATION Power supply 10-24V DC 1. (Read Master Add Card) RF
01 02 03
Wiring Common Power Supply OPERATION Delete Users Door status detection Setting (factory default is closed) Set Wiegand Input/ Output
Number Wire Color Definition Function Optional Programming Step Keystroke Combination Programming Step Keystroke Combination Programming Step Keystroke Combination
1 Orange NC Normally Closed Relay Output 1N4004
- Magnetic Lock or
Fail-Safe Lock
Enter and Exit Program mode 1.Enter Program Mode
*(Master Code) # 1.Enter Program Mode (Master Code) #
* 1.Enter Program Mode
* (Master Code) #
Common Connection for Relay NC Orange + Programming Step Keystroke Combination 2. Delete Card - By Card 2 (Read Card) # 2.Close the setting of magnetic 6 0 # 2.Wiegand Input 8 1 # (factory default)
2 Purple COM 1N4004
COM Purple OR OR OR
Output
NO Blue
Fail-Secure Lock Enter Program Mode * (Master Code) #
(Factory default is777777) 2. Delete Card - By ID number 2 (Input ID number) # 2.Open the detection setting 61# 2.Wiegand Output 82#
3 Blue NO Normally Open Relay Output
3.Exit Program Mode
4 Black GND Negative Power
GND Black GND Exit Program Mode
* 2. Delete All User 2 0000 # 3.Exit Program Mode
* *
+12V Red DC10~24V
3.Exit Program Mode
5 Red +12V Positive power
OPEN Yellow Optional
DC Power Supply
For safety, the Admin must change the Admin code.
* When you activate the door status detection
6 Yellow OPEN Request to Exit (REX) Input Exit Button If you forgot to close the door in 1 min, the buzzer will alarm. When
D_IN Brown + the door closed or swipe valid card, the buzzer will be release.
D_IN Door Contact Alarm
7 Brown Door/Gate Contact Input ARM- Grey - Set Alarm Time
If the door opened by force, the buzzer and external alarm will
8 Grey ARM- Negative contact for alarm D0 Green Can connect external reader, managing in activated at the same time. Programming Step Keystroke Combination
9 Green D0 Wiegand Input/ Output Data 0 D1 White and out by reader. Or works as Wiegand reader.
Set Master Code 1.Enter Program Mode
2.Set the mode of relay
* (Master Code) #
9 (0-3) # (factory default is 1 minute)
10 White D1 Wiegand Input/ Output Data 1 WM1-MF Programming Step Keystroke Combination
3.Exit Program Mode
Power + +
1.Enter Program Mode
* (Master Code) # *
1N4004 Lock 0 (New Master Code) # Note: "0" means no alarm. Read valid card (or master code #/ Master
Fail-Safe Lock: NC - card) can stop alarm or reminder.
Fail-Secure Lock: NO 2.Update Master Code (Repeat New Master Code) #
(Master Code is any 6 digits)
Connection Diagram Attention Set Relay Configuration
3.Exit Program Mode
Access Control Power Supply Install a 1N4004 or equivalent diode is needed when use a common power supply, * Programming Step Keystroke Combination
or the keypad might be damaged. (1N4004 is included in the packing) The length of the admin code is 6 digits, the admin should keep it in
(Master Code) #
Access Control mind. 1.Enter Program Mode
*
Power Supply 2.Toggle Mode 4 0 # (OFF) 4 1 #(ON) Safe Mode setting (factory default is off)
PUSH
COM
GND
NO
NC
04 05 06 07 08 09