Professional Documents
Culture Documents
1000
Data sheet
110105_en_00 © PHOENIX CONTACT 2021-12-06
1 Description
With the left-alignable AXC F XT ML 1000 extension
Ensure that the left-alignable extension module is
module, you can extend an AXC F 3152 PLCnext controller
only aligned next to a PLCnext controller which
with a machine learning module for processing AI
has a firmware version that is permissible for this.
applications.
AXC F 3152 PLCnext controllers with firmware
Features versions 2022.0 LTS are permitted.
This data sheet is only valid in association with the UM EN AXL F SYS INST user manual.
2 Table of contents
1 Description .............................................................................................................................. 1
2 Table of contents ..................................................................................................................... 2
3 Ordering data .......................................................................................................................... 3
4 Technical data ......................................................................................................................... 4
5 Internal circuit diagram ............................................................................................................ 6
6 For your safety......................................................................................................................... 7
6.1 Intended use ...................................................................................................................... 7
6.2 Qualification of users ............................................................................................................ 7
6.3 Electrical safety ................................................................................................................... 7
6.4 Installation ......................................................................................................................... 7
3 Ordering data
4 Technical data
126,93
123
Width 45 mm
Height 126.93 mm
Depth 75 mm
Note on dimensions The depth is valid when a TH 35-7,5 DIN rail is used (according
to EN 60715).
General data
Type modular
Axioline
Mounting type DIN rail mounting
Color traffic grey A RAL 7042
Weight 149 g (with connector and bus base module)
Ambient temperature (operation) -25 °C ... 60 °C (up to 2000 m above sea level)
Permissible humidity (operation) 0 % ... 90 % (according to DIN EN 61131-2)
Air pressure (operation) 70 hPa ... 106 kPa (up to 3000 m above sea level)
Degree of protection IP20
Protection class III (IEC 61140, EN 61140, VDE 0140-1)
Mechanical tests
Vibration resistance in acc. with EN 60068-2-6/ 5g
IEC 60068-2-6
Shock in acc. with EN 60068-2-27/IEC 60068-2-27 30g
Continuous shock according to EN 60068-2-27/ 10g
IEC 60068-2-27
Approvals
For the latest approvals, refer to: phoenixcontact.net/product/1259849
Logic / FE
TPU
UL
UL
24V
UL
24 V
Key:
LED
6.4 Installation
Please note:
Please note:
Only one left-alignable extension module of one
If you have already operated the controller with left
type can be connected to one PLCnext controller.
alignment, you can skip this section.
Connecting additional left-alignable extension
modules of the same type is not possible. In this case, proceed as described in Section
“Mounting the left-alignable extension module”.
Please note:
A controller needs a special bus base module for operation
Mount all the modules required before supplying with left-alignable extension modules.
power to the Axioline F station. Modules to which You must prepare the controller for operation with left-
power is only supplied following the controller boot alignable extension modules once by replacing the existing
process are not detected or may result in a bus base module of the controller with the special bus base
malfunction. module.
To ensure that the left-alignable extension module
is detected correctly, proceed as follows:
The special bus base module is not included in the
• Switch on the power to the left-alignable
scope of delivery of all AXC type controllers.
extension module and to the controller
For the ordering data, please refer to the user
simultaneously.
manual for the controller you are using.
8.1 Removing the controller supply connector To replace the existing bus base module of the controller
with the special bus base module, first remove the
• Disconnect the power to the controller.
electronics module of the controller:
• Release the locking latch (A), tilt the supply connector
• Insert a suitable tool (e.g., bladed screwdriver) into the
upwards slightly (B), and remove it from the controller
upper and lower snap-on mechanisms (base latches) of
(C).
the controller one after the other and release it (A).
Figure 3 Removing the supply connector The base latches are locked in place in the open position.
• Remove the electronics module vertically out of the DIN
rail (B).
Figure 4 Remove the electronics module of the
D
R
A
-C
D
S
R
controller
X
X
.X
X
.X
52
X
.X
21
X
.X
F
X
.X
C
X
X
X
A
r.:
67
dd
A
42
C
40
A
M
2
o.
.N
rd
O
A
2
X
1
X
B
52
21
F
C
X
X
.X
A
X
.X
7
26
X
.X
04
S
X
D
24
.X
-C
R
X
A
o.
R
.X
D
.N
X
X
rd
r.:
X
O
4
dd
A
C
A
M
A
X
1
X
2
X
2
X
1
Then mount the special bus base module (A and B in • Remove the electronics module from the adjacent
Figure 5): extension module on the right.
• Place the special controller bus base module on the DIN • If necessary: Remove the cover cap on the adjacent
rail (A). bus base module on the right (A).
• Push the special bus base module of the controller into • Place the bus base module of the left-alignable
the connection for the bus base module of the adjacent extension module on the DIN rail (B).
module on the right (B). • Push the bus base module of the left-alignable
You can now mount the left-alignable extension module; to extension module into the connection on the adjacent
do so, see Section “Mounting the left-alignable extension bus base module on the right (C).
module”. Figure 6 Remove cover and mount the bus base
module
8.4 Mounting the left-alignable extension module
b1
alignable extension module must be supplied via a a2 b2
a2 b2
24 V
GND
EXT
110105_en_00 PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany 11/11
phoenixcontact.com