Professional Documents
Culture Documents
Ips Led Monitor (Led LCD Monitor) : Owner'S Manual
Ips Led Monitor (Led LCD Monitor) : Owner'S Manual
OWNER’S MANUAL
IPS LED MONITOR
(LED LCD MONITOR)
Please read this manual carefully before operating
your set and retain it for future reference.
www.lg.com
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
2 TABLE OF CONTENTS
CONTENTS
ENGLISH
ENG
13 CUSTOMIZING SETTINGS
14 Customizing Settings
14 - Menu Settings
15 - Picture
16 - Color
17 - Display
18 - Others
19 READER Setting
20 - SUPER ENERGY SAVING
ASSEMBLING AND PREPARING 3
ENGLISH
ENG
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
Audio Cable
Power Cord Stand Base ( Depending on the country )
CAUTION
Do not use any unapproved accessories to ensure the safety and product life span.
yy
Any damages or injuries by using unapproved accessories are not covered by the warranty.
yy
NOTE
The accessories supplied with your product may vary depending on the model.
yy
Product specifications or contents in this manual may be changed without prior notice due to upgrade
yy
of product functions.
4 ASSEMBLING AND PREPARING
Power Indicator
y yLED On : Power is on
y yLED Off: Power is off
(Power Button)
ENGLISH
Attaching the Stand Base 1 Place the monitor's screen face down.
ENG
To protect the screen from scratches, cover the
1 Place the Monitor set with the screen side surface with a soft cloth.
down on a flat and cushioned surface.
CAUTION
2 Using a coin, turn the screw in the stand base
To protect the screen from scratches, cover
yy counterclockwise. Detach the stand base from
the surface with a soft cloth.
the stand body.
Stand Body
Stand Base
Stand Base
CAUTION
3 Using a coin, turn the screw clockwise to se-
cure the stand base. The components appearing in the illustra-
yy
tions may look different from the actual prod-
uct.
Do not carry the monitor upside-down as this
yy
may cause it to fall off its stand, resulting in
damage or injury.
To avoid damaging the screen when lifting
yy
or moving the monitor, only hold the stand or
the plastic cover. This avoids putting unnec-
essary pressure on the screen.
Only remove the tape and the locking pin
yy
when the monitor is mounted on the stand
base and is in an upright position. Otherwise,
the stand body may protrude, which may
lead to injury.
Stand Base
6 ASSEMBLING AND PREPARING
ENGLISH
1 Lift the monitor and place it on the table in an 1 Place the monitor mounted on the stand base
ENG
upright position. in an upright position.
Install at least 10 cm away from the wall to
ensure sufficient ventilation. 2 Adjust the angle of the screen. The angle of
the screen can be adjusted up to 5° forwards
and 20° backwards for a comfortable viewing
experience.
10 cm
10 cm
10 cm
10 cm
WARNING
2 Connect the Power cord to the monitor, then
plug the power cord into the wall outlet. To avoid injury to the fingers when adjusting
yy
the screen, do not hold the lower part of the
monitor's frame as illustrated below.
CAUTION
Unplug the power cord prior to moving or
yy
installing the monitor. There is risk of electric
shock.
8 ASSEMBLING AND PREPARING
Tape
Locking Pin
110.0mm
NOTE
Using the Kensington lock is optional. The
yy
accessories can be purchased at your local
electronics store.
CAUTION
Once the pin is removed, it is not necessary
yy
to re-insert it to adjust the height.
WARNING
Do not put your finger be-
yy
tween the screen and the
base (chassis) when adjust-
ing the screen's height.
ASSEMBLING AND PREPARING 9
ENGLISH
ENG
set.
1 Swivel 355 degrees and adjust the angle of the
Monitor set to suit your view.
Head
section
Stand
section
10 ASSEMBLING AND PREPARING
on each side and from the wall. Detailed VESA (A x B) 75 x 75 100 x 100
instructions are available from your dealer, see the Standard screw M4
optional Tilt Wall Mounting Bracket Installation and Number of screws 4
Setup Guide.
CAUTION
Disconnect the power cord first, and then
yy
10 cm move or install the Monitor set. Otherwise
electric shock may occur.
10 cm If you install the Monitor set on a ceiling or
yy
10 cm slanted wall, it may fall and result in severe
injury.
10 cm Use only an authorized LG wall mount
yy
and contact the local dealer or qualified
personnel.
Do not over tighten the screws as this may
yy
cause damage to the Monitor set and void
your warranty.
yy Use only screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
4 VESA compatible.
5 Please use VESA standard as below.
784.8 mm (30.9 inch) and under
yy
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
787.4 mm (31.0 inch) and above
yy
* Please use VESA standard wall mount pad
and screws.
USING THE MONITOR SET 11
ENGLISH
ENG
Connecting to a PC DVI-D connection
Your Monitor set supports Plug & Play*.
yy Transmits a digital video signal from your PC to
*Plug & Play: A PC recognizes a connected the Monitor set. Connect the PC and the Monitor
device that users connect to a PC and turn set with a DVI cable as shown in the following
on, without device configuration or user illustrations.
intervention.
D-SUB connection
Transmits analog video from your PC to the
Monitor set. Connect the PC and the Monitor set
with the supplied D-sub 15 pin signal cable as
shown in the following illustrations.
NOTE
When you want to use two PC in our Monitor,
yy
please connect the signal cable(D-SUB/
DVI-D) respectively in Monitor set.
If you turn the Monitor set on while it is cold,
yy
the screen may flicker. This is normal.
Some red, green, or blue spots may appear
yy
on the screen. This is normal.
NOTE
Connect peripheral devices to the monitor using Press the power button on the bottom panel to
ENGLISH
ENG
headphone ports. turn the power on. When monitor power is turned
on, the "Self Image Setting" Function is executed
automatically. (Only supported in Analog Mode)
NOTE
NOTE
CUSTOMIZING SETTINGS
ENGLISH
ENG
1 Press the desired button on the bottom of the Monitor set.
2 Change the value of the menu item by pressing the buttons on the bottom of the Monitor set.
To return to the upper menu or set other menu items, use the up arrow ( ) button.
3 Select EXIT to leave the OSD menu.
Button Description
Accesses the main menus.(See p.14)
OSD Locked/OSD This function allow you to lock the current control settings, so
Unlocked that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds. Then
OSD of “OSD Lock” will appear. After that, user can select
lock or unlock by pressing left/right button.
If user selects the “Lock” icon by pressing the “OK” button,
the message “OSD Locked” will appear. Otherwise, “OSD
Unlocked” will appear. After selecting the “Lock”, If you want
to change to Unlock, you can push the “MENU” button for
several seconds. The message “OSD Unlocked” will appear.
Use this button to enter Reader Mode menu. Its function works to display screen as
paper-like picture for Eye comfort.If you want to more information.(See p.19)
Use this button to enter SUPER ENERGY SAVING menu.(See p.20)
When adjusting your display settings, always press the AUTO button on the MONITOR
SETUP OSD. (Only supported in Analog Mode)
The best display mode 19MB35PM:1280 x 1024
22MB35PM/23MB35PM:1920 x 1080
You can choose the input signal.
• When two input signals are connected, you can select the input signal (D-SUB/DVI)
you want.
• When only one signal is connected, it is automatically detected. The default setting is
D-SUB.
EXIT
Exit the OSD(On Screen Display).
(Power Button) Turns the power on or off.
Power Indicator The power indicator stays white if the display is running
properly (On Mode). If the display is in Sleep Mode, the power
indicator blinks white.
14 CUSTOMIZING SETTINGS
Customizing Settings
Menu Settings
ENGLISH
Picture
ENGLISH
1 Press MENU button on the bottom of the Monitor set
ENG
to display the Menu OSD.
Color
ENGLISH
Display
ENGLISH
1 Press MENU button on the bottom of the Monitor set
ENG
to display the Menu OSD.
Others
ENGLISH
READER Setting
ENGLISH
1 Press READER button on the bottom of the Monitor
ENG
set to display the Reader Mode OSD.
NOTE
If option of Reader Mode is Reader 1 or Reader 2, Picture Mode will automatically be Custom and
Super Energy Saving will automatically be Off.
20 CUSTOMIZING SETTINGS
NOTE
TOTAL POWER REDUCTION: How much power is saved while using the monitor.
yy
TOTAL CO2 REDUCTION: Change the TOTAL POWER REDUCTION to CO2.
yy
SAVING DATA(W/h)
yy
482 mm 546 mm 584 mm
(19 inch) (21.5 inch) (23 inch)
SUPER SAVING (High) 3 W/h 4 W/h 4 W/h
SUPER SAVING (Low) 1 W/h 2 W/h 2 W/h
Saving Data depends on the Panel. So,those values should be different from each panel and panel
yy
vendor.If option of Super Energy Saving is High or Low, monitor luminance become higher or lower
depend on source.
LG calculated these values by using “broadcast video signal”
yy
(including broadcast video: IEC 62087)
SUPER SAVING refers to how much power can be saved using the SUPER ENERGY SAVING
yy
function.
If option of Super Energy Saving is High or Low, Picture Mode will automatically be Custom and
yy
Reader Mode will automatically be Reader Off.
TROUBLESHOOTING 21
TROUBLESHOOTING
ENGLISH
ENG
Check the following before calling for service.
No image appears
Is the power cord of the display y y Check and see if the power cord is connected properly to the power
connected? outlet.
Is the power indicator light on? y y Press the Power button.
Is the power on and the power y y Adjust the brightness and the contrast.
indicator White?
Is the power indicator flickering? y y If the display is in power saving mode, try moving the mouse or
pressing any key on the keyboard to bring up the screen.
y y Try to turn on the PC.
Do you see an "OUT OF RANGE" y y This message appears when the signal from the PC (video card) is
message on the screen? out of horizontal or vertical frequency range of the display. See the
'Specifications' section of this manual and configure your display
again.
Do you see a "NO SIGNAL" y y When the monitor is on "No-Signal" in 5 minutes, the monitor goes to
message on the screen? DPM mode.
CAUTION
ENGLISH
Check Control Panel ► Display ► Settings and see if the frequency or the resolution were
yy
ENG
Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message?
Have you installed the display y y Be sure to install the display driver from the display driver CD (or
driver? diskette) that comes with your display. Or, you can also download the
driver from our web site: http://www.lg.com.
y y Make sure to check if the video card supports Plug&Play function.
SPECIFICATIONS 23
SPECIFICATIONS
ENGLISH
19MB35PM
ENG
Display Screen Type TFT (Thin Film Transistor) LCD (Liquid Crystal Display)
Panel,Anti-Glare coating
48.2 cm visible diagonal (19 inch)
Pixel Pitch 0.294 mm x 0.294 mm (Pixel Pitch)
Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)
Vertical Frequency 56Hz to 75Hz (D-SUB,DVI-D)
Input Form Separate Sync. Digital
Video Input Signal Input 15 pin D-SUB Connector /DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Resolution Max D-SUB(Analog) : 1280 x 1024 @ 60 Hz
DVI (Digital) : 1280 x 1024 @ 60 Hz
Recommend VESA 1280 x 1024 @ 60 Hz
Plug & Play DDC 2B(Analog,Digital)
Power On Mode : 15 W (ENERGY STAR® standard)*
Consumption Sleep Mode ≤ 0.3 W
Off Mode ≤ 0.3 W
Power Input AC 100-240V ~ 50/60Hz 0.8 A
Speaker Wattage 1 W +1 W
Dimensions With Stand 40.9 cm x 48.1 cm x 21.0 cm
(Width x Height x Without Stand
Depth) 40.9 cm x 33.8 cm x 5.8 cm
Weight 3.8 kg
Tilt Range -5° to 20°
Environmental Operating Temperature 10°C to 35 °C
conditions Operating Humidity 10 % to 80 %
Storage Temperature -20°C to 60 °C
Storage Humidity 5 % to 90 % non-Condensing
Stand Base Attached ( ), Detached (O)
Power cord Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
* The power consumption level can be different by operating condition and monitor setting.
* The On mode power consumption is measured with ENERGY STAR® test standard.
* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.
24 SPECIFICATIONS
SPECIFICATIONS
ENGLISH
22MB35PM
ENG
Display Screen Type TFT (Thin Film Transistor) LCD (Liquid Crystal Display)
Panel,Anti-Glare coating
54.6 cm visible diagonal (21.5 inch)
Pixel Pitch 0.248 mm x 0.248 mm (Pixel Pitch)
Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)
Vertical Frequency 56Hz to 75Hz (D-SUB,DVI-D)
Input Form Separate Sync. Digital
Video Input Signal Input 15 pin D-SUB Connector /DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Resolution Max D-SUB(Analog) : 1920 x 1080 @ 60 Hz
DVI (Digital) : 1920 x 1080 @ 60 Hz
Recommend VESA 1920 x 1080 @ 60 Hz
Plug & Play DDC 2B(Analog,Digital)
Power On Mode : 20 W (ENERGY STAR® standard)*
Consumption Sleep Mode ≤ 0.3 W
Off Mode ≤ 0.3 W
Power Input AC 100-240V ~ 50/60Hz 1.0 A
Speaker Wattage 1 W +1 W
Dimensions With Stand 50.9 cm x 35.3 cm x 22.4 cm
(Width x Height x
Depth) Without Stand 50.9 cm x 30.4 cm x 14.4 cm
Weight 3.9 kg
Tilt Range -5° to 20°
Environmental Operating Temperature 10°C to 35 °C
conditions Operating Humidity 10 % to 80 %
Storage Temperature -20°C to 60 °C
Storage Humidity 5 % to 90 % non-Condensing
Stand Base Attached ( ), Detached (O)
Power cord Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
* The power consumption level can be different by operating condition and monitor setting.
* The On mode power consumption is measured with ENERGY STAR® test standard.
* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.
SPECIFICATIONS 25
SPECIFICATIONS
ENGLISH
23MB35PM
ENG
Display Screen Type TFT (Thin Film Transistor) LCD (Liquid Crystal Display)
Panel,Anti-Glare coating
58.4 cm visible diagonal (23 inch)
Pixel Pitch 0.2652 mm x 0.2652 mm (Pixel Pitch)
Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)
Vertical Frequency 56Hz to 75Hz (D-SUB,DVI-D)
Input Form Separate Sync. Digital
Video Input Signal Input 15 pin D-SUB Connector /DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Resolution Max D-SUB(Analog) : 1920 x 1080 @ 60 Hz
DVI (Digital) : 1920 x 1080 @ 60 Hz
Recommend VESA 1920 x 1080 @ 60 Hz
Plug & Play DDC 2B(Analog,Digital)
Power On Mode : 21 W (ENERGY STAR® standard)*
Consumption Sleep Mode ≤ 0.3 W
Off Mode ≤ 0.3 W
Power Input AC 100-240V ~ 50/60Hz 1.0 A
Speaker Wattage 1 W +1 W
Dimensions With Stand 54.8 cm x 36.7 cm x 24.6 cm
(Width x Height x
Depth) Without Stand 54.8 cm x 33.5 cm x 16.6 cm
Weight 4.5 kg
Tilt Range -5° to 20°
Environmental Operating Temperature 10°C to 35 °C
conditions Operating Humidity 10 % to 80 %
Storage Temperature -20°C to 60 °C
Storage Humidity 5 % to 90 % non-Condensing
Stand Base Attached ( ), Detached (O)
Power cord Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
* The power consumption level can be different by operating condition and monitor setting.
* The On mode power consumption is measured with ENERGY STAR® test standard.
* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.
26 SPECIFICATIONS
19MB35PM
Horizontal Vertical
Display Modes (Resolution) Polarity(H/V)
Frequency(kHz) Frequency(Hz)
720 x 400 31.468 70 -/+
640 x 480 31.469 60 -/-
640 x 480 37.500 75 -/-
800 x 600 37.879 60 +/+
800 x 600 46.875 75 +/+
1024 x 768 48.363 60 -/-
1024 x 768 60.023 75 -/-
1152 x 864 67.500 75 +/+
1280 x 1024 63.981 60 +/+
1280 x 1024 79.976 75 +/+ Recommend Mode
22MB35PM 23MB35PM
Horizontal Vertical
Display Modes (Resolution) Polarity(H/V)
Frequency(kHz) Frequency(Hz)
720 x 400 31.468 70 -/+
640 x 480 31.469 60 -/-
640 x 480 37.500 75 -/-
800 x 600 37.879 60 +/+
800 x 600 46.875 75 +/+
1024 x 768 48.363 60 -/-
1024 x 768 60.023 75 +/+
1152 x 864 67.500 75 +/+
1280 x 1024 63.981 60 +/+
1280 x 1024 79.976 75 +/+
1680 x 1050 65.290 60 -/+
1920 x 1080 67.500 60 +/+ Recommend Mode
Indicator
Mode LED Color
On Mode White
Sleep Mode Blinking White
Off Mode Off
PROPER POSTURE 27
PROPER POSTURE
ENGLISH
ENG
Proper posture for using the Monitor set.
Adjust the
Monitor set and Adjust the location of the
your posture to Monitor set to avoid it
allow you to view reflecting light.
images at the
optimal viewing
angle.