Professional Documents
Culture Documents
FEATURES
Direct connection of thermal, floating, or proportional
actuators
NOTE: VC series actuators generate high-voltage pulses
in the end position and therefore cannot be used
in conjunction with SERVAL.
Direct connection for up to three fan stages
Direct connection to electrical heat
Supports (via relays) staged fan (up to 3 stages) or (via
0…10 V output) variable-speed fan
Supports (via 0…10 V output) one proportional valve
(alternatively to variable-speed fan)
Factory-configured default parameters
Wide range of supported valves and actuators
GENERAL Interlocks and time delays to protect equipment
Uses Echelon LonTalk® protocol
The SERVAL Controller is an individual room controller which Wall modules for manual override
can be used for a wide range of control applications. It can Slim design fits into narrow fan coil units and false
operate as a stand-alone unit or as a part of a CentraLine ceilings
control system.
Power supplied by power mains or 24 V
Interfaces are provided for a wide range of actuator types. eu.bac certified
Heating systems can be water or electric, and cooling sys-
tems can be chilled water supply or compressors. Extensive
timing and interlock features make them especially suitable
for systems using electrical heat and compressors.
DESCRIPTION
The SERVAL Controller provides room temperature control
Table 1. Overview of models
for two- and four-pipe control circuits with optional electrical
CLSE…. heating coils and can control single-, two-, or three-speed, or
description
1L230 1L24 2L230 2L24 3L230 variable-speed fans (depending upon model – see Table 1). It
SERVAL 230 V X -- X X X
has factory-set default configuration settings and is fully
power operable upon installation. Using the COACH configuration
supply 24 V -- X -- -- -- tool, the controller can be configured with project-specific
230 V X -- X -- X settings. Using the CARE engineering tool, the controller can
Triac
voltage 24 V be configured by means of an LNS plug-in. A variety of
-- X -- X --
COMMAND wall modules interface with the controller and
1st relay (fan I) X X X X X provide any or all of the following: setpoint adjustment, fan
2nd relay (fan II) X X X X X speed adjustment, and an occupancy bypass button. All wall
3rd relay (fan III) X X X X X modules include a space temperature sensor; however, a
4th relay (reheat) X X X X -- remote C7068A return air sensor can also be used.
DOs triac (open OUT1) X X X X X
triac (close OUT1) X X X X --
triac (open OUT2)
triac (close OUT2)
X
X
X
X
X
X
X
X
X
X
SEQUENCES
LED X X X X X Heat and cool sequences can be selected to be active or not
config. dig. input X X X X X active, giving a total of ten different room applications:
DIs digital input Radiator with heating valve
X X X X X
(window contact) Floor heating with heating valve
fan speed + occ.
X X X X X Floor heating/ cooling with changeover valve
override
AIs Chilled ceiling with cooling valve
room sensor X X X X X
Chilled ceiling with heating/ cooling changeover valve
set-pt. adjustment X X X X X
var.-speed fan con-
Radiator with heating valve, chilled ceiling with cooling
AO trol or OUT1 or -- -- X X - valve
0…10 V OUT2 Fancoil unit with heating + cooling valve
Fancoil unit with heating + cooling + electric reheat
Fancoil unit with heating/ cooling changeover valve
Fancoil unit with heating/ cooling changeover valve +
electric reheat relay
triac
8 9 10 11 12 10A 3A 0.5 A
GND
SENS
SET
N L
24 V
fan
LON 53 4 2 1 24 V
L OUT1 OUT2
CLCM N
wall modules 24 Vdc
EN0Z-0911GE51 R1117 2
SERVAL CONTROLLER – PRODUCT DATA
Environmental Ratings
Operating temperature: 0...50°C Fig. 2. CLSE1L230 sticker with input/output details
Shipping/storage temperature: -40...+70°C
Relative humidity: 5% to 95% non-condensing
Dimensions
110 x 180 x 60 mm
Weight
Fig. 3. CLSE1L24 sticker with input/output details
CLSE1L230: 420 g
CLSE1L24: 420 g
CLSE2L230: 420 g
CLSE2L24: 700 g
CLSE3L230: 420 g
Communications
The SERVAL Controller uses the LonTalk protocol. It
supports the LONMARK Functional Profile # 8020 “Fan Coil Fig. 4. CLSE2L230 sticker with input/output details
Unit Controller”, version 2.0.
Accessories
COMMAND Wall Modules
Dew-Point Sensor H7018A1003
LONWORKS termination module XAL-Term2
M7410C Small Electric Linear Valve Actuator
M6410L Small Electric Linear Valve Actuator
M5410C Small Electric two-position actuators
M4410C and M4410L Small Linear Thermoelectric
Actuators Fig. 6. CLSE3L230 sticker with input/output details
XAL-COV-L Terminal Covers (8 pcs. bulk) – necessary
for wall mounting
System Components
configuration software: COACH
front-end software: ARENA
graphic editor: ARENA EDITOR
3 EN0Z-0911GE51 R1117
SERVAL CONTROLLER – PRODUCT DATA
Manufactured for and on behalf of the Environmental & Energy Solutions Division of Honeywell Technologies Sàrl, Rolle, Z.A. La Pièce 16, Switzerland by its Authorized Representative:
CentraLine
Honeywell GmbH
Böblinger Strasse 17
71101 Schönaich, Germany
Phone +49 (0) 7031 637 845
Fax +49 (0) 7031 637 740
info@centraline.com Subject to change without notice
www.centraline.com EN0Z-0911GE51 R1117