Professional Documents
Culture Documents
Ordering information
SPA 030 24
05 5VDC
Output voltage
12 12VDC
24 24VDC
030 30W
Output power 050 50W
075 75W
100 100W
Item
SPA Switching Mode Power Supply
Specifications
SPA- SPA- SPA- SPA- SPA- SPA- SPA- SPA- SPA- SPA- SPA- SPA-
Model
030-05 050-05 030-12 050-12 030-24 050-24 075-05 100-05 075-12 100-12 075-24 100-24
Capacity 30W 50W 30W 50W 30W 50W 75W 100W 75W 100W 75W 100W
Power supply※5 100-240VAC(85-264VAC) 100-120/200-240VAC(85-132/170-264VAC)
Frequency 50/60Hz
Input
Efficiency※1 Min. 60% Min. 67% Min. 74% Min. 80% Min. 70% Min. 78% Min. 72% Min. 78% Min. 80%
Current consumption※1 Max. 1.2A Max. 1.6A Max. 1.0A Max. 1.4A Max. 0.8A Max. 1.1A Max. 3.0A Max. 2.0A Max. 3.0A Max. 2.0A Max. 2.5A
Voltage 5VDC 12VDC 24VDC 5VDC 12VDC 24VDC
Current 6A 10A 2.5A 4.2A 1.5A 2 .1A 15A 20A 6.3A 8.5A 3.2A 4.2A
Votage fluctuation range※4 ±5%
Output
P-8
Switching Power Supply
20 20
(D)
0 0 Proximity
-10 0 10 20 30 40 50 60 70 80 90 -10 0 10 20 30 40 50 60 70 80 90
sensor
Ambient temperature (℃) Ambient temperature (℃)
● SPA-030-12 ● SPA-050-12 ● SPA-075-12 (E)
Pressure
Load 120 Load 120 sensor
ratio Forced cooling
100 ratio
(%) 100 Forced cooling
(%) (F)
80 80
Rotary
Natural cooling Natural cooling encoder
60 60
40 (G)
40 Connector/
Socket
20 20
0 0 (H)
-10 0 10 20 30 40 50 60 70 80 90 -10 0 10 20 30 40 50 60 70 80 90 Temp.
Ambient temperature (℃) Ambient temperature (℃) controller
Output
voltage ● It is when the rated input voltage is 100VAC, 100%. (U)
(V) ● It is able to protect overcurrent by load with built-in Other
P-9
SPA Series
Block diagram
Inrush current
protection Rectifier Rectifier
(L) circuit circuit circuit
Input power
Noise
85-264VAC
filter
50/60Hz
(N)
Control
circuit Voltage
detection
F·G
Overcurrent
protection
circuit
0V
DC OUT
+V
LED LED
4
4
VR VR
2-M3
87
97
87
97
5-M3.5 2-M3
5-M3.5 (Bottom side)
(Bottom side)
45.5
38.5
3.5
3.5
6
6
4 154
4 114
9.5
3.5
3.5
7.5
20
40
42
3.5
28
3.5
28
17.5
22.5
29
29
83 25 138 10
114 154
120 160
P-10
Switching Power Supply
For switch input voltage type, input voltage is 220V as ① Please mount the device on metal panel for the (B)
Fiber
factory default.To swich input voltage for 110V, remove the reliability. optic
cover then select proper jumper switch as below figures. ② Please mount the device in a ventilative place for high sensor
SPA-030-05 (E)
SPA-030-12 Pressure
sensor
SPA-050-12 SPA-050-05
110V 220V SPA-075-12 SPA-075-05
Model (F)
SPA-030-24 SPA-100-05 Rotary
encoder
SPA-050-24 SPA-100-12
2. Technical information of operation SPA-075-24
① This product is not available to operate of output voltage SPA-100-24 (G)
Connector/
as parallel and series. Socket
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other
P-11