Professional Documents
Culture Documents
that changes or modifications not expressly approved by the part responsible for compliance could void
the user’s authority to operate the equipment. This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
Technical Specifications on, the user is encouraged to try to correct the interference by one or more of the following measures:
Maximum Output Power: Approximately 250 mW (16 Ω) (a) Reorient or relocate the receiving antenna; (b) move this unit; (c) increase the separation between the
equipment and receiver; (d) connect the equipment into an outlet on a circuit different from that to which
Maximum Drive Ability: 16–150Ω the receiver is connected; (e) be sure that all cables are properly shielded, using a choke or ferrite where
Signal-to-Noise Ratio: > 90 dB (A-weighted) appropriate; (f) consult the dealer or an experienced radio/television technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
Connections: 2 1/8” (3.5 mm) TRRS outputs; 1 1/8” (3.5 mm) TRRS input; conditions: (1) this device may not cause harmful interference, and (2) this device must accept
1 micro-USB port any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits
Power: Internal lithium-polymer battery with 8-hour capacity set forth for an uncontrolled environment. End users must follow the specific operating instructions for
Dimensions (width x depth x height): 1.84” x 1.80” x 0.60” / 46.9 x 45.7 x 15.2 mm satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter. For best audio quality, avoid using this device in a high RF-
Weight: 0.07 lbs. (1.12 oz.) / 0.03 kg (30 g) radiated environment. RSS Statement for Canadian models: This device complies with Industry
Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
Warnings: device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device This unit does not exceed the Class B
• Excessive sound pressure (high volumes) from headphones can cause limits for radio noise emission from digital apparatus set out in the radio interference regulations of the
hearing loss. Canadian Department of Communications.
ESD/EFT Warning: This unit may contain a microcomputer for signal processing and control
• To reduce the risk of fire or electrical shock, do not expose this product to functions. In very rare situations, severe interference, noise from an external source, or static
rain, liquids, or moisture. Electrical equipment should never be kept or electricity may cause it to lock up. In the unlikely event that this should happen, turn off the unit,
stored in damp environments. Do not expose this product to dripping or wait at least five seconds, and then turn it back on again. In an environment with radio frequency
interference, the unit may malfunction and resume normal operation after removal of the interference.
splashing, and do not place objects filled with liquids on it.
Correct Disposal of This Product: This marking indicates that this product should not be
• Danger of explosion if battery is incorrectly replaced. Replace only with the disposed with other household wastes throughout the EU. To prevent possible harm to the
same or equivalent type. environment or human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources. To return your used device, please
use the return and collection systems or contact the retailer where the product was
Specifications are subject to change without notice. v1.3 purchased. They can take this product for environmentally safe recycling.
Features:
User Guide (English)
For more information about this product (system requirements,
1. Off/Volume: Turn this knob to adjust the 1 5 5
volume of the outputs. The knob’s
compatibility information, etc.), product registration, or product support,
minimum position is off.
visit m-audio.com.
For safety and warranty information, visit m-audio.com/warranty. 2. Battery Indicator: This light indicates
Bass Traveler’s current power status: on,
Package Contents: Bass Traveler, micro-USB cable, 1/8” (3.5 mm)
charging its battery, or low on battery
TRRS connector cable, User Guide. power.
3. Charging Port: Use the included micro- 2
Quick Start:
USB cable to connect this micro-USB
Items not listed in Package Contents are sold separately. port to a USB port on your computer
Important: Charge Bass Traveler for at least 2 hours before using it for
the first time.
(powered on). Alternatively, connect it to
a USB power adapter (sold separately)
6 4 3
1. Make sure Bass Traveler is charged and powered off (the Off/Volume connected to a power outlet.
knob should be in the minimum position). 4. Input: Connect your audio source to this
2. Use the included 1/8” (3.5 mm) cable to connect your audio source to 1/8” (3.5 mm) TRRS input.
Bass Traveler’s input. 5. Outputs: Connect your 1/8” (3.5 mm)
3. Connect your 1/8” (3.5 mm) headphones to the output/outputs. headphones to these outputs.
4. Turn the Off/Volume knob clockwise until it “clicks” on. The battery 6. Boost: Set this switch to a desired setting.
indicator will be lit blue. The Flat setting applies no equalization
5. Play your audio source, and turn the Off/Volume knob to adjust the (EQ). M applies a slight boost in EQ. H
volume of the headphones. applies the maximum amount of EQ.
6. Optional: To add more equalization (EQ) to the audio in the
headphones, set the Boost switch to the desired setting. Trademarks and Licenses: M-Audio is a trademark of inMusic Brands, Inc.,
registered in the U.S. and other countries. All other product or company names are
trademarks or registered trademarks of their respective owners.