Professional Documents
Culture Documents
L
1
BRIDGE
2
BRIDGE
3
BRIDGE
4
BRIDGE L
F POWER MODE
OUTPUTS
1 2 3 4
ZONE
L 1 R L 2 R
G
OUT R R
1 2 3 4 5 6 7 8
ZONE
ON L 1 R L 2 R L 3 R L 4 R
12V
GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN L 5 R L 6 R L 7 R L 8 R
AUDIO
LINK TO GLOBAL INPUT
OUT R R
FUSE RATING T6.3A_H 250V CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP ALL 2 3 4 5 6 7 8
INSTALLING THE AMPLIFIER CONNECTING AUDIO INPUTS IMPORTANT! The common signal of these speaker outputs must
not be connected together or to any other common signal. Do
The 4-Zone and 8-Zone Power Amplifiers come with rack-mount ears and The 4-Zone and 8-Zone Power Amplifiers accepts stereo line-level audio not connect the L – and R – (negative) terminals together. Doing
can be installed in a 1U rack space. connections to their inputs jacks. Each zone input will pass amplified audio so will result in a fault condition and the amplifier will either shut
to the respective zone speaker output. Alternatively, each zone can be down or not work properly.
Installing the 4-Zone and 8-Zone Power Amplifiers in a rack: linked individually to the GLOBAL IN (shared with input 1).
CAUTION! Check the polarity of the speakers and wires before
1 Attach the rack ears to the sides of the amplifier using the provided 1 Connect the audio cables to the ZONE INPUTS (1-8) audio input jacks. connecting to the amplifier.
screws. 8 ZONE ATTENTION ! Vérifiez la polarité des enceintes et des câbles
POWER AMP avant de brancher à l’amplificateur.
8 ZONE
12V GLOBAL OUT GLOBAL IN
AC POWER 100V-240V ~50-60Hz 105W
IN
TRIGGER
L
1 2 3 4 5 6 7 8
L
To connect bridged speakers:
8 ZONE
BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE
OUTPUTS
POWER MODE
1 2 3 4 5 6 7 8
ZONE
ON L 1 R L 2 R L 3 R L 4 R
POWER AMP
1 Set the BRIDGE MODE dipswitch, if needed, for each zone by moving
12V
GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN L 5 R L 6 R L 7 R L 8 R
AUDIO
LINK TO GLOBAL INPUT
OUT R R
OUTPUTS
POWER MODE
TRIGGER 1 2 3 4 5 6 7 8
1 2 3 that zone
4 to the 5On position. 6 7 8
ZONE
ON L 1 R L 2 R L 3 R L 4 R
12V
GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN L 5 R L 6 R L 7 R L 8 R
IN L L AUDIO
8 ZONE
BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE
OUTPUTS
POWER MODE
OUT R 1 2 3 4 5 6 7 8 4R R
ZONE
ON L 1 R L R L 3 L
GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN
12V
L 5 R L 6
channel
R L 7
(L).
R L 8 R
POWER AMP
AUDIO
LINK TO GLOBAL INPUT
OUT R FUSE RATING T6.3A_H 250V CLIP CLIP CLIP R CLIP CLIP CLIP CLIP CLIP ALL 2 3 4 5 6 7 8
AC POWER 100V-240V ~50-60Hz 105W
12V
TRIGGER
GLOBAL OUT GLOBAL IN 3 Connect the - terminal from the speaker to the - terminal of the right
1 2 3 4 5 6 7 8
Note: Rack ears canFUSE
beRATING
installed
T6.3A_H 250V to the front or the back of
CLIP
the CLIP IN L CLIP BRIDGE CLIP
BRIDGE BRIDGE CLIP BRIDGE CLIP
BRIDGE BRIDGE CLIP BRIDGE BRIDGE CLIP L ALL POWER
2 3MODE4 5 6 7 8 channel (R) on the amplifier.
OUTPUTS
1 2 3 4 5 6 7 8
ZONE
ON L 1 R L 2 R L 3 R L 4 R
12V
amplifier as needed.
GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN L 5 R L 6 R L 7 R L 8 R
Move switch up to
AUDIO
LINK TO GLOBAL INPUT
OUT R R
2 Install into rack and connect cabling. FUSE RATING T6.3A_H 250V CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP ALL 2 3 4 5 6 7 8
ON position to link The two terminals for a bridged pair of
to global input speakers are marked by + BRIDGE -.
CAUTION! To prevent damage, maintain adequate ventilation space
to the sides of the amplifier. Amplifiers can be stacked vertically, POWER MODE
but be sure not to place the amplifier next to other components 3 (Optional) Connect an audio cable to the GLOBAL OUT to duplicate L
L
1
5
R
R
L
L
2
6
R
R
L
L
3
7
R
R
the audio source connected to the GLOBAL IN and pass that audio to
L
OUTPUTS
POWER MODE
ZONE
ON L 1 R L 2 R L 3 R L 4 R
12V
L 5 R L 6 R L 7 R L 8 R
POWER MODE L
1 2 3 4 5 6 7 8
BRIDGE
OUTPUTS
POWER MODE
1 2 3 4 5 6 7 8
ZONE
ON 1 R 2 3 R L 4 R
ZONE
L L R L
ON L 1 R L 2 R L 3 R L 4 R
AUDIO R
LINK TO GLOBAL INPUT
6 7 8
R R
the amplifier. UnplugOUTthe power cord before making connections. CLIP ALL 2 3 4 5 6 7 8
FUSE RATING T6.3A_H 250V CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP ALL 2 3 4 5 6 7 8 To set up the amplifier to be always on:
AVERTISSEMENT ! Les fils se reliants de haut-parleur ou les câbles
entrés tandis que l’amplificateur est actionné, peuvent causer le 1 Slide the POWER MODE switch to ON.
choc et pourraient endommager l’amplificateur. Débranchez le
cordon de secteur avant d’établir des rapports. In this mode, the amplifier will be always on unless the power cord is
unplugged or the power switch by the power cord is toggled off.
To set up the amplifier to be controlled by a 12V trigger: SPECIFICATIONS Thermal dissipation Three fans mounted in the
left side
Three fans mounted in the
left side
1 Slide the POWER MODE switch to 12V.
Thermal dissipation (heat losses) 0.23W / 0.8 BTU/hr, standby 0.23W / 0.8 BTU/hr, standby
GENERAL 8-ZONE 4-ZONE 40W / 136.5 BTU/hr, idle, all 25W / 85.3 BTU/hr, idle, all
2 Connect the 12V trigger cable from the trigger device to 12V TRIGGER channels channels
IN. Triad Power Amplifier TS-PAMP8-100 TS-PAMP4-100
8 ZONE Audio inputs 8 stereo, RCA style 4 stereo, RCA style
100W / 341 BTU/hr, max
output, all ch. driven
100W / 341 BTU/hr, max
output, all ch. driven
POWER AMP 12V
Global audio input 1 stereo analog (shared with 1 stereo analog (shared with
GLOBAL OUT GLOBAL IN
AC POWER 100V-240V ~50-60Hz 105W
TRIGGER
1 2 3 4 5 6 7 8 zone 1 input) zone 1 input) MISCELLANEOUS 8-ZONE 4-ZONE
IN L BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE BRIDGE L
OUTPUTS
POWER MODE
1 2 3 4 5 6 7 8
Global audio output 1 stereo analog (from shared 1 stereo analog (from shared
ZONE
Mains switch w/ changeable fuse Yes Yes
ON L 1 R L 2 R L 3 R L 4 R
12V
GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN L 5 R L 6 R L 7 R L 8 R
Power connection IEC 320 C13 power connector IEC 320 C13 power connector
Amplifier is powered on, in standby with 3-pole detachable power with 3-pole detachable power
cord cord
Amplifier zone(s) are on
THERMAL 8-ZONE 4-ZONE
Zone(s) are in over-current protection
Operating temperature 32 °F ~ 113 °F (0 °C ~ 45 °C) 32 °F ~ 113 °F (0 °C ~ 45 °C)
Storage -4 °F ~ 158 °F (-20 °C ~ 70 °C) -4 °F ~ 158 °F (-20 °C ~ 70 °C) Copyright ©2018, Control4 Corporation. All rights reserved. Control4, the Control4 logo, Triad, and the Triad logo
are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. All
specifications subject to change without notice.