Professional Documents
Culture Documents
RMT-833
SERVICE MANUAL
US Model
Ver 1.0 2003. 11 Canadian Model
CCD-TRV128/TRV328
E Model
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428E
Australian Model
Hong Kong Model
CCD-TRV428E
Argentine Model
Brazilian Model
CCD-TRV128
Link
TM
SERIES
SPECIFICATIONS
—2—
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
• Abbreviation
AR : Argentine model CND : Canadian model JE : Tourist model
AUS : Australian model EE : East European model NE : North European model
BR : Brazilian model HK : Hong Kong model
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point : LEAD FREE MARK
them out to the customer and recommend their replacement. Unleaded solder has the following characteristics.
4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than
of deterioration. Point them out to the customer and ordinary solder.
recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified.
Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
• Keep the temperature of the soldering iron around 270˚C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
• Do not touch the soldering iron on the same conductor of the • Strong viscosity
circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than
• Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such
or unsoldering. as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
—3—
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
TABLE OF CONTENTS
Section Title Page Section Title Page
1. SERVICE NOTE 5. REPAIR PARTS LIST
1-1. Note for Repair ································································ 1-1 5-1. Exploded Views ···························································· 5-2
1-2. Power Supply During Repairs ········································· 1-1 5-1-1. Overall Assembly ·························································· 5-2
1-3. To Take Out a Cassette when not Eject (Force Eject) ····· 1-2 5-1-2. Front Panel Block ························································· 5-3
1-4. LCD Type Check ····························································· 1-3 5-1-3. Lens Block ···································································· 5-4
1-5. Self-diagnosis Function ··················································· 1-4 5-1-4. LCD Block ···································································· 5-5
1-5-1. Self-diagnosis Function ··················································· 1-4 5-1-5. Cabinet R Block ···························································· 5-6
1-5-2. Self-diagnosis Display ····················································· 1-4 5-1-6. EVF Block ···································································· 5-7
1-5-3. Service Mode Display ····················································· 1-4 5-1-7. Battery Panel Block ······················································ 5-8
1-5-4. Self-diagnosis Code Table ··············································· 1-5 5-1-8. MD Frame Block ·························································· 5-9
5-1-9. Cassette Compartment Assembly, Drum Assembly ··· 5-10
5-1-10. LS Chassis Block Assembly ······································· 5-11
2. DISASSEMBLY 5-1-11. Mechanical Chassis Block Assembly-1 ······················ 5-12
2-1. Flow Chart ······································································· 2-1 5-1-12. Mechanical Chassis Block Assembly-2 ······················ 5-13
2-2. Mechanism Deck Service Position ·································· 2-3 5-2. Electrical Parts List ····················································· 5-14
2-3. LCD Service Position ······················································ 2-5
2-4. Circuit Boards Location ·················································· 2-6
2-5. Flexible Boards Location ················································ 2-7
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/5) ··········································· 3-1
3-2. Overall Block Diagram (2/5) ··········································· 3-3
3-3. Overall Block Diagram (3/5) ··········································· 3-5
3-4. Overall Block Diagram (4/5) ··········································· 3-7
3-5. Overall Block Diagram (5/5) ··········································· 3-9
3-6. Power Block Diagram (1/2) ··········································· 3-11
3-7. Power Block Diagram (2/2) ··········································· 3-13
—4—
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
SECTION 1
SERVICE NOTE
Method 1.
Use the AC power adaptor (AC-L10, AC-VQ800 etc.).
1-1
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
Timing belt
Loading motor
Disconnect CN401
of VC-341 board.
1-2
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
Preparations:
1) Connect the equipment for adjustments according to Fig. 1.
2) Connect the adjustment remote commander to VC-341 board CN007 via I/F unit for LANC control (J-6082-521-A) and CPC jig connector
(J-6082-539-A).
To operate the adjustment remote commander, connect the AC power adaptor to the DC IN jack of I/F unit for LANC control, or connect
the L series Info-LITHIUM battery to the battery terminal of I/F unit for LANC control.
Checking method:
1) Select page: 3, address: CC.
2) By checking the data value of display data, the type of LCD can be discriminated.
CN007
1
16
CPC lid
Screw (M2)
L serices Info
LITHIUM battery (7.2Vdc)
AC adaptor AC IN
AC adaptor AC IN
Conductor side
LANC jack
Adjustment CPC jig connector
remote commander (RM-95) (J-6082-539-A)
1-3
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
Blinks at 3.2Hz
C 31 11
1. Display Method
While pressing the “STOP” key, set the switch from OFF to “ON”, and continue pressing the “STOP” key for 5 seconds continuously. The
service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
Viewfinder Display window
[3] C : 3 1 : 1 1 3 C : 3 1 : 11
Lights up
[3] C:31:11
3. End of Display
Turning OFF the power supply will end the service mode display.
Note: The “self-diagnosis display” data will not be erased (reset), when the lithium battery (CONTROL KEY BLOCK (CF-
5100): BT001) is removed.
1-4
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
1-5
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
Self-diagnosis Code
Repaired by:
Inspect the lens block focus reset sensor (Pin qs of CN201 of VC-
Difficult to adjust focus 341 board) when focusing is performed when the control dial is
E 6 1 0 0
(Cannot initialize focus.) rotated in the focus manual mode and the focus motor drive circuit
(IC201 of VC-341 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin qg of CN201 of VC-
Zoom operations fault 341 board) when zooming is performed when the zoom switch is
E 6 1 1 0
(Cannot initialize zoom lens.) operated and the zoom motor drive circuit (IC201 of VC-341 board)
when zooming is not performed.
Steadyshot function does not work well.
Inspect pitch angular velocity sensor (SE752 of SI-039 board)
E 6 2 0 0 (With pitch angular velocity sensor output
peripheral circuits. *1
stopped.)
Steadyshot function does not work well.
Inspect yaw angular velocity sensor (SE751 of SI-039 board)
E 6 2 0 1 (With yaw angular velocity sensor output
peripheral circuits. *1
stopped.)
*1: STEADYSHOT model (CCD-TRV328/TRV428/TRV428E)
1-6E
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
SECTION 2
DISASSEMBLY HELP
4 5 8 4
1 7
3 4
3 3
7 8 5
6 1
6
6
2 2 3 1
2
5 2
1 Lift up the EVF. 5 EVF Cabi (upper) 1 VC-341: CN004 5 VC-341: CN006
2 Tapping P2 x4 6 EVF Cabi (lower) 2 VC-341: CN053 6 Tapping P2 x1 1 VC-341: CN151 4 Lock ace x2
3 Down the EVF. 7 FP-797: LCD902 3 Lock ace x3 7 Lock ace x1 2 VC-341: CN201 5 Boss
4 EVF block 8 EVF lens 4 EVF/Battely panel block 8 SS-5100 3 Lens sheet 6 Lens LSV-820A
2 2
3
7
3 1 2
8
4
1 5 6
1 1
1 Tapping P2 x4 1 VF blind sheet 5 Claw
2 Claw x2 2 VC-341: CN402, CN403, CN481 6 Open the VC-341. 1 Screw (M1.7) x3
3 P Cabi (C) 3 VC-341: CN401 7 VC-341: CN404 2 CS frame
4 Screw (M1.7) x2 8 VC-341
2-1 2-2
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
Setting the "Forced Camera Power ON" mode Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01. 1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02 and 2) Select page: D, address: 10, data: 00, and press the PAUSE
press the PAUSE button of the adjustment remote button of the adjustment remote commander.
commander. 3) Select page: 0, address: 01, and set data: 00.
Setting the "Forced VTR Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02 and
2 1 press the PAUSE button of the adjustment remote
commander.
1
6 2 B
5 Press the cassette compartment
7 in the direction of the arrow A
9 A
to move it up in the direction of
the arrow B.
4
1 1
8 Lens block
3 4 6
Adjustment remote
commander (RM-95)
I/F unit for LANC control
(J-6082-521-A)
4
8
7
4 3 Cabinet R block
Eject switch
3
EVF block/
5 Battery panel block assembly
Control key block
1 6 (SS-5100)
6 AC IN AC adaptor
1
2 3 When exiting the "Forced Power ON" mode, connect the control
5 2
key block (SS-5100) to the CN006 of VC-341 board. Or, when
ejecting the cassette, connect the control key block (SS-5100) to
the CN006 of VC-341 board. and press the Eject switch.
2-3 2-4
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
LCD panel 16
AC adaptor AC IN
LANC jack
Adjustment
remote commander (RM-95)
2-5
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
VC-341
CD-465
SI-039
PD-204
2-6
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
FP-797 SS-5100
FFC-005
CF-5100
FP-792
FP-795
PR-5100
2-7E
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Harness (PD-124)
Claw
Claw
HELP
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
3. BLOCK DIAGRAMS
Link
TEMP
ZM SENSE OUT
FC SENSE OUT
ZM SENSE VCC
FC SENSE VCC
ADCK
A,B,XA,XB A,B,XA,XB BIAS(+) HALL(+) HALL(-) BIAS(-) 28.636363MHz : TRV128/TRV228/TRV328/TRV428
28.375MHz : TRV228E/TRV428E
(1/10) 9 1
D 2.8V
44 AHD, AVD
5 7 17 19 2 4 21 23 1 2 5 14 8 4 OVERALL (2/5)
IC202 45
IC201 XSG1 (PAGE 3-3)
(3/10) 5 34
(3/10) XV1
ZOOM FOCUS HALL HALL HALL IRIS 41
OVERALL (3/5) XCS IC 301 ID
48
MOTOR
DRIVE
MOTOR
DRIVE
BIAS AMP GAIN DRIVE
(PAGE 3-5) 2 XRST VTR
39
40 36
V STOP
13 – 16 9 – 12 3 6 7 12 10 CAM DD ON
42 35
ZM RST
FC RST
EN1 EN0 HALL HALL HALL HALL IRIS PWM OVERALL (3/5) CK CONT 1, 2 47 38 VC SO, VC SI, XVC SCK
DIR1A DIR0A REF OFFSET AD GAIN (PAGE 3-5) 17 46 37 EN0, DIR0A,B,
XNS SW
EN1, DIR1A,B,
DIR1B DIR0B
FC RST, ZM RST
Q202 (1/2)
D 2.8V
CL 16
HALL OFFSET,
OVERALL (3/5)
HALL GAIN,
(PAGE 3-6)
HALL REF
OVERALL (2/5)
Q202 (2/2)
3 (PAGE 3-4)
CS CH, CH SO, CH SCK
ZM RST LED
FC RST LED OVERALL (3/5) VC SO, VC SI, XVC SCK
LENS TEMP AD
4 (PAGE 3-5)
IRIS PWM
XNS SW 5
TRV328/TRV428/TRV428E HALL AD, OVERALL (3/5)
SI-039 BOARD (1/2) PITCH AD (PAGE 3-5)
YAW AD
SE752 CN755 (1/2) CN009 (1/2)
LIA 1 IC271 PITCH AD XCS AU
PITCH SENSOR 26 5 8 2
STEADY BEEP
SE751 SHOT DCOUT JACK IN
LIA 2 (10/10) YAW AD
YAW SENSOR 24 7 12 18 AV JACK IN
XS JACK IN
IR ON
AV JACK IN AV JACK IN
14 17
J753
RFU DC DCOUT JACK IN DCOUT JACK IN
1 30
OUT
SIRCS PWM
SIRCS SIG 8
XF TALLY LED OVERALL (4/5)
CONTROL KEY BLOCK (CF-5100) (1/2) CN008 (PAGE 3-8)
SP901 1 SP (+), (–)
SPEAKER 2 A : VIDEO SIGNAL
A : AUDIO SIGNAL
05
3-1 3-2
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
3. BLOCK DIAGRAMS
3-2. OVERALL BLOCK DIAGRAM (2/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
PB C RF CH
SP1
CN481 FLYING
ERASE
REC RF SP1X
187 7 6 27 5
AD1 – AD10 ı RF AGC OUT
IC301 51 9 28
196
CAMERA/VTR PB C RF IC481 SP2X
49 11 34 7
CLP1 PROCESS, ATF, REC/PB AMP
183 Q484, 485 CH
LENS CONTROL (4/10) 33
PBLK (2/10) SP2
172 SWITCH 10
Q481 – 483
MCK, CL 81
ERASE
164
AGC SLOW
HEAD
FE (X)
11
M2100/M2101
ADCK
BOTH REC
46 OSC MECHA DECK (1/2)
185 M2100: TRV128/TRV228/TRV328/TRV428
OVERALL (3/5) RP PB MODE
OVERALL (1/5)
(PAGE 3-2) 1 198 (PAGE 3-5) 12 13 M2101: TRV228E/TRV428E
DOP
7
AHD, AVD 169 DA STRB
170
DOP
XSG1 77
166
XV1
168 15
XRF AGC OFF
ID XCS IC 301 6 REC Y/MT CONT
171 98 OVERALL (3/5) 3 3
V STOP 99
XRST VTR 11 (PAGE 3-5) RF AGC CONT 4
REC L CONT
48
167 25 MT FO 38
5 15
EN0, DIR0A, B, DOC DET
148 26 12 39
EN1, DIR1A, B RP IR
ı 24 8
153 AFC F0 ADJ AFC F0 ADJ REC BIAS
66 23 IC251 21 32
FC RST, ZM RST 161 MT Q
EVR 20 19
162 (D/A CONVERTER) 14 1 47
(4/10) CN007
95 XMP/ME
ı VC SO, VC SI, XVC SCK 7 (1/3)
97 REC RF
7
Q306 PB RF 9 CPC
IC 301 Y OUT HALL OFFSET, 2
BUFFER 4 FSC HALL GAIN, BPF MONI (FOR CHECK)
OVERALL (1/5)
79
3 HALL REF 17 3
(PAGE 3-2) 7 OVERALL (1/5)
ı
IC 301 C OUT 19
213 (PAGE 3-1)
VI HD XRST VTR
146 24 4 RF SWP
VI VDO IC302
67 144 23 REC AFM
Q304 CGCK CHARACTER
179 8 GENERATOR PB RF
OVERALL (3/5) AFC F0
(PAGE 3-5) 9 VCO 53 OSD P ON, (2/10) A FADE A FADE
OSD R ON, 12 OVERALL (1/5)
180 OSD L ON 19 9
1.5M DEV 1.5M DEV 6 (PAGE 3-2)
ı 17 AU BPF AU BPF
LCD HOLD 182 1 10
15 FCS
58 COLOR 1 ı 27 FRQ TUNE FRQ TUNE
ı VC SO, XVC SCK
XCS OSD, OSD SO, XOSD SCK
22 3 22
JOG VD 174 COLOR 4 28
83 ı
X1/2 SWP ı
84 177 20 XFE ON
XSG V RST 18
86 RF SWP RF SWP
ATF SAMPLE 16
87
MECHA FLD, MECHA HD,
MECHA VD 89 FSC
OVERALL (3/5) Q302
(PAGE 3-5) 10 93
94 14
PANEL R PANEL R VI VDO VIVDO 15 OVERALL (3/5)
(PAGE 3-5)
SYS V PANEL G PANEL G
88 17 BUFFER
SWP DIR PANEL B PANEL B
85 24
PANEL HD XCS OSD, OSD SO, XOSD SCK
CK CONT1, 2 101 75
100 PANEL VD
XTBC V RST 74
157 PANEL SYNC
TBC VD 76
158 EVF BLOCK
CN004 LCD902
EVF G/BW Y VIDEO IN B/W
34 6
CN002 (1/2) PANEL VD VSYNC LCD UNIT
5
PANEL HOLD PANEL HD HSYNC
4
14 NSLEEP
2
7 PANEL R, PANEL G, PANEL B
ı
5
C-SYNC/XHD PANEL SYNC
9
OVERALL (5/5) PANEL XVD PANEL VD
(PAGE 3-9) 18 8 EVF DD ON
11
ı VC SO, VC SI, XVC SCK VC SO, VC SI, XVC SCK
13 OVERALL (3/5) A : VIDEO SIGNAL
13 (PAGE 3-5)
10
XCS LCD DA XCS LCD A : AUDIO SIGNAL
A : VIDEO/SERVO SIGNAL
BL CONT BL CONT OVERALL (4/5)
4 14 (PAGE 3-8)
A : VIDEO/AUDIO/SERVO SIGNAL
05
3-3 3-4
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
3. BLOCK DIAGRAMS
3-3. OVERALL BLOCK DIAGRAM (3/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
TAPE TOP TAPE TOP TAPE TOP TAPE TOP (C) Q001
19 19 18 1 TAPE TOP
DETECT SENSOR
AGC SLOW
11
BOTH REC T REEL FG T REEL FG
168 119 28 T REEL 26 T REEL (+) , (–) 9 T REEL H001
RP PB MODE SENSOR
OVERALL (2/5) 169 FG AMP 27 10
(PAGE 3-4) 12 DOP
10 S REEL FG S REEL FG
203 120 24 S REEL 22 S REEL (+) , (–) 7 S REEL H002
DA STRB FG AMP 23 6 SENSOR
46
Q401
TAPE LED ON TAPE LED ON TAPE LED (K)
201 LED DRIVE 3
OVERALL (2/5) AFC F0 S001
(PAGE 3-3) 9 117 213
REC PROOF REC PROOF
13 REC PROOF
ME SW ME SW
212 12 ME/MP
HI8 MP SW HI8 MP SW 14
214 HI8 MP
XCC DOWN 15
XFE ON C. C. LOCK
170 S002
RF SWP LCD HOLD
159 163
VIVDO
OVERALL (2/5) 206 JOG VD
(PAGE 3-4) 15 80
155
X1/2 SWP
157
XCS OSD, OSD SO, XOSD SCK ı XSG V RST
154
82 ATF SAMPLE
156
134
MECHA FLD, MECHA HD, MECHA VD
3 173 OVERALL (2/5)
X601
20MHz 204 10 (PAGE 3-3)
1 SYS V
181
SWP DIR
158
95 CK CONT1, 2
96
XTBC V RST
179
TBC VD
205
63
IC701 SO, IC701 SI, IC701 SCK, XCS IC701 ı
66 CK CONT1, 2 OVERALL (1/5)
CUSTOM LED ON
52
17 (PAGE 3-2) SI-039 BOARD FP-792 FLEXIBLE
ZOOM VR AD (2/2) BOARD
OVERALL (4/5) 133
(PAGE 3-8) 19 DCOUT ON SYS V OVERALL (4/5)
OSD V
115
208
20 (PAGE 3-8)
D001 – 003
(VIDEO LIGHT)
XSYS RST Q001 CN009 CN755
9 (2/2) (2/2)
XCC DOWN 8 VIDEO LIGHT VL+ LND756
VL 16V 1 30
DRIVE
V LIGHT PWM
91
IC602
XCS EEP
EEPROM 1 87
CN007
(6/10) 86 EEP SI, EEP SO, EEP SCK
(2/3)
84
256 XCS EEP XCS EEP
85 16
CAP FG
4
SWP DIR 5 CPC
15 (FOR CHECK)
EEP SI, EEP SO, EEP SCK EEP SI, EEP SO, EEP SCK 14
1 A : SERVO SIGNAL
05
3-5 3-6
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
3. BLOCK DIAGRAMS
3-4. OVERALL BLOCK DIAGRAM (4/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN007
(3/3)
12 LANC IN 39
CPC LANC OUT
11 40
XLANC POWER ON
(FOR CHECK) 13 8
D 2.8V
IC051 (2/2)
AU 2.8V
MODE DC CONTROL,
EP 2.8V
S002 RESET
A 4.6V (9/10) VTR UNREG
XEJECT SW 16 XEJECT SW 4
EJECT SW AU 4.6V BATT UNREG BT901
EP 4.6V CN053
D004 Q053, 054 Q051, 052
XCHARGE LED XCHARGE LED RP 4.6V 4 +
CHG 6 12 MT 5V 3 – DC IN
VL 16V
D002
XCAM LED XCAM LED CAM –7.5V
CAMERA 8 11 CHARGE
CAM 15V 2
CONTROL
EP 13.5V
D001
XVTR LED XVTR LED PANEL –15.3V
PLAY/EDIT 9 9
6 +
EVER 3.0V BATTERY
RV001 5 S
VOUT TERMINAL
ZOOM VR ZOOM VR 12 ZOOM VR AD 1 –
LANC DC 47
Q075
20 27
CONTROL KEY BLOCK (CF-5100) (2/2) 21 HI EVER SO, HI EVER SCK 28
BATT IN
S024 31 44
CN005 VTR DD ON
35 38
XCS DD
SEL/PUSH DIAL A, B 19 DIAL A, B 79 49 26
EXEC 20 80
DIAL XRESET
45
5 59 BATT/XEXT VBAT
74 39
MENU EXEC FUNCTION KEY AD0 – KEY AD3 14 KEY AD0 – KEY AD3 ı FAST CHARGE
INIT CHARGE ON
37 D053
61 REG 3V
FAST CHARGE
SW 18 INIT CHARGE ON 40
65 38
16
BATT/XEXT
BATT SIG
Q701
S001
43 BATTERY BATT SIG
DISP/ XBATT INFO SW
6 3 CHARGE
BATT INFO SW 42
DETECTOR
S002
XRESET
RESET SW 22 73
DCOUT ON
Q002
D002 XCC DOWN XCC DOWN
CUSTOM LED ON LED 5
EASY 9 XSYS RST XSYS RST
DRIVE 47
23
ı IC 701 SO, IC 701 SI, IC 701 SCK, XCS IC 701 IC 701 SO, IC 701 SI, IC 701 SCK, XCS IC 701
LI 3V 26
BT001 3 OVERALL (3/5)
LITHIUM 19
OSD V OSD V 19 (PAGE 3-5)
BATTERY
ZOOM VR AD ZOOM VR AD
CUSTOM LED ON CUSTOM LED ON
05
3-7 3-8
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
3. BLOCK DIAGRAMS
3-5. OVERALL BLOCK DIAGRAM (5/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
ND901
BACKLIGHT
D6004
BL CONT BL CONT BL DET BL LOW
4 28 30 3
A : VIDEO SIGNAL
05
3-9 3-10
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
3. BLOCK DIAGRAMS
3-6. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
D054
SI-039 43 VIN VR 34
BOARD EVER 3.0V
36 CDET VRO 41
(1/2) V OUT
VOUT 42
J753 LI 3V
VBAT 39
CN755 CN009
RFU DC (1/2) (1/2) 55 VCC1 REG 3V 40
OUT 56 VCC0 D053
RFU DC 3 28 BATT IN
CS 44
2 29 XCS DD
Q055 LD 26
HI EVER SO
54 LANC DC DIN 27
HI EVER SCK
53 SENS CLK 28
VTR DD ON
52 VCONT CTL1 38
XCTL2 47
DCOUT ON TYPE C/S: Please refer to page 1-3 to descriminate the type of LCD.
Q075
CAM DD ON A
IC051 POWER(2/2)
PD- 204 BOARD
(PAGE 3-13)
DC CONTROL, Q057 L052 L059
RESET BL REG TYPE C
SWITCHING
(9/10)
CN6004 LCD901
OUT2 58 L6004
PANEL 4.6V R6026 VSH
IN2 21 24
+INE2 14 PANEL –15.3V R6019 VGL
3
37 VREF PANEL 13.5V R6020 VGH 2.5INCH
Q056 L055 L058 1
1 DTC6 D 1.5V PANEL 2.8V VDD COLOR
SWITCHING 23 LCD UNIT
VDD
L061 L6001 FB6001 4
OUT1 57 D 2.8V R6031
IN1 20 L060 A 2.8V
30 RT
Q058 L056 L062 AU 2.8V IC6001
SWITCHING BL CONT
28
FB051 LCD DRIVER
OUT3 59
IN3 22 D055 Q066, 073
CAM –7.5V
–7.5V REG
Q062 Q064, 067, 070
CAM 15V
SWITCHING +15V REG
TYPE S
OUT7 63
Q6004, 6005,
–INE7 2 6008, 6009 CN6004 LCD901
L6004
PANEL 4.6V VSH5V 24
L051 L065 18
EP 4.6V PANEL –15.3V VGL
Q059 L057 16 3
L063 A 4.6V PANEL 13.5V VGH 2.5INCH
SWITCHING 19 1
PANEL 2.8V VSH3V COLOR
L064 17 23
AU 4.6V LCD UNIT
OUT4 60 FB6001
L066 L6001
IN4 23 RP 4.6V
VL 16V
BL CONT IC6001
Q071, 072 4 28 24
EP 13.5V LCD DRIVER
13.5V REG
05
3-11 3-12
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
3. BLOCK DIAGRAMS
3-7. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
EVER 3.0V
D 2.8V
LI 3V D 2.8V 17
VTR DD ON 35 D 2.8V FUNCTION
15
D 2.8V
D 2.8V SWITCH
4
EVER 3.0V
LI 3V LI 3V BT001
3
BATT IN LITHIUM
XCS DD D002 BATTERY
CUSTOM LED VDD
7 EASY
HI EVER SO
HI EVER SCK
VTR DD ON IC301 IC152
IC251 IC302 IC151
TRV328/TRV428/TRV428E
EVR CHARACTER CAMERA/VTR S/H. AGC. TIMING
DCOUT ON GENERATOR
(D/A CONVERTER) GENERATOR PROCESS, ATF, A/D CONVETER
A CAM DD ON
(4/10) (2/10) LENS CONTROL (1/10) (1/10)
L271 IC271 SI-039 BOARD
D753, 754
POWER (1/2)
(2/10) (2/2)
STEADY (IR EMITTER)
(PAGE 3-12) FB251 FB252 FB152 L151 FB151 SHOT
(10/10)
TRV228/TRV228E/TRV328/
TRV428/TRV428E
CN009 CN755
MT 5V
L301
L302
L303
D 1.5V D 1.5V (2/2) (2/2)
MT 5V MT 5V MT 5V 14 17 IC751
15 16 D759
REMOTE
D 2.8V D 2.8V D 2.8V D 2.8V (TALLY)
12 19 COMMANDER
RECEIVER
A 2.8V A 2.8V A 2.8V A 2.8V 9 22
AU 2.8V 10 21 TRV328/TRV428/TRV428E
AU 2.8V
CAM –7.5V CAM –7.5V CAM –7.5V
SE751, 752
CAM 15V CAM 15V CAM 15V YAW, PITCH
EP 4.6V EP 4.6V EP 4.6V SENSOR
A 4.6V A 4.6V FP-792 FLEXIBLE BOARD
Q001
AU 4.6V AU 4.6V
VIDEO VL+ LND756
RP 4.6V VL UNREG VL UNREG
LIGHT 1 30
VL 16V
VTR UNREG
DRIVE
D001 – 003
D 2.8V
MT 5V
EP 13.5V L202
(VIDEO LIGHT)
FB601
IC801 IC202
IC602 IRIS DRIVE,
IC601 AUDIO/VIDEO
EEPROM PROCESS HALL BIAS CONTROL,
CAMERA/MECHA L801
V LIGHT PWM
(6/10) (8/10) HALL GAIN CONTROL,
CONTROL HALL AMP
IC401 (6/10)
(3/10)
DRUM/ EVF BLOCK
FB401
CAPSTAN/ CN004 LCD902
LOADING V LIGHT PWM 91
EVF DD ON NSLEEP
MOTOR DRIVE EVF DD ON 26 2
L483 IC481 (5/10) ZM RST LED 49 B/W
EP 4.6V EVF 4.6V
REC/PB FC RST LED 50 3 LCD
L481 L201
VMR
(4/10)
115 DCOUT ON IC201 IC001
3 17 3.3V 3.3V
162 CAM DD ON 1 3.3V REG 4 1
FOCUS/ZOOM
(10/10)
IRIS DRIVE(+)
TAPE LED (A)
MOTOR DRIVE
SENSOR VCC
CAM –7.5V
(3/10)
ZM SENS
FC SENS
CAM 15V
FG VCC
TEMP
SP1Y
SP2Y
VCC
VCC
VH+
3 5
CN951
CD-465
L951
VIDEO TAPE T REEL, CAPSTAN ZOOM IRIS BOARD
S REEL, HU, HV, HW
HEAD LED FG SENSOR METER
SENSOR IC951
D001
H001,002 FOCUS TEMP CCD
SENSOR SENSOR IMAGER
M2100/M2101 MECHA DECK M2100: TRV128/TRV228/TRV328/TRV428
M2101: TRV228E/TRV428E LENS BLOCK
3-13 3-14E
I
A
J
F
L
E
K
C
B
N
H
G
D
05
1
LND759 REG_GND
LND756 VL+
LND760 REG_GND
FP-792
BOARD
2
FLEXIBLE
LND754
MIC_GND
SI-039
BOARD
LENS
INT_MIC
MIC901
BLOCK
LND755
MICROPHONE
3
CN201 24P
IRIS_DRIVE(+) 24
IRIS_HALL(+) 23
KEY
IRIS_BIAS(+) 22
BLOCK
IRIS_HALL(-) 21
IRIS_BIAS(-) 20
CONTROL
(PR-5100)
DCOUT_JACK_IN
RFU_DC
RFU_DC
REG_GND
S_C_I/O
REG_GND
XS_JACK_IN
REG_GND
S_Y_I/O
REG_GND
VIDEO_I/O
REG_GND
AUDIO_L_I/O
AV_JACK_IN
SIRCS_PWM/IR_DRV_EN
MT_5V
MT_5V
XSIRCS_SIG
D_2.8V
XF_TALLY_LED
A_2.8V
A_2.8V
VREF2
LIA2
VREF1
LIA1
INT_MIC
MIC_GND
MIC_GND
VL+
CN755 30P
IRIS_DRIVE(-) 19
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
TEMP 18
TEMP 17
BOARD
CD-465
ZM_SENSE_VCC 16
FRAME SCHEMATIC DIAGRAM
2
1
4
5
6
3
FC_SENSE_VCC 13
4-1. FRAME SCHEMATIC DIAGRAMS
9
8
7
6
5
4
3
2
1
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
FC_SENSE_OUT 12
N.C.
N.C.
GND 11
VL+
LIA2
LIA1
5
CN6005
SE_GND
SE_GND
CN009
VREF2
VREF1
MT_5V
MT_5V
A_2.8V
A_2.8V
D_2.8V
ZOOM_A 10
S_C_I/O
S_Y_I/O
RFU_DC
RFU_DC
INT_MIC
MIC_GND
MIC_GND
PANEL_REV
PANEL_REV
REG_GND
REG_GND
REG_GND
REG_GND
REG_GND
6P
VIDEO_I/O
ZOOM_B 9
XSIRCS_SIG
30P
XS_JACK_IN
AV_JACK_IN
AUDIO_L_I/O
XF_TALLY_LED
ZOOM_XB 8
CCD_OUT
GND
CAM_-7.5V
VSHT
CAM_15V
GND
RG
H1
H2
GND
V1
V2
V3
V4
DCOUT_JACK_IN
CN951 14P
ZOOM_XA 7
SIRCS_PWM/IR_DRV_EN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
IR_SWITCH 6
4-1
IR_SWITCH 5
CN6001 20P CN002 20P
FOCUS_A 4
AD5 20 20 AD5
FOCUS_B 3
PANEL_13.5V 19 19 PANEL_13.5V
6
FOCUS_XB 2
PANEL_4.6V 18 18 PANEL_4.6V
FOCUS_XA 1
SECTION 4
PANEL_2.8V 17 17 PANEL_2.8V
CN151 14P
PANEL_-15.3V 16 16 PANEL_-15.3V
CCD_OUT 14
REG_GND 15 15 REG_GND
GND 13
PANEL_HOLD 14 14 PANEL_HOLD
CAM_-7.5V 12
VC_SI(HDO) 13 13 VC_SI(HDO)
VSHT 11
VC_SO 12 12 VC_SO
CAM_15V 10
XVC_SCK 11 11 XVC_SCK
7
GND 9
XCS_LCD_DA 10 10 XCS_LCD_DA
RG 8
PD-124
CPC
C-SYNC/XHD 9 9 C-SYNC/XHD
HARNESS
H1 7
(FOR CHECK)
PANEL_XVD 8 8 PANEL_XVD
FLAT CABLE
H2 6
PANEL_R 7 7 PANEL_R
FFC-005 FLEXIBLE
GND 5
1
2
3
4
5
6
7
8
9
BOARD
10
11
12
13
14
15
16
PD-204
PANEL_G 6 6 PANEL_G
V1 4
PANEL_B 5 5 PANEL_B
V2 3
PB_RF
PB_RF
EEP_SI
CAP_FG
REC_RF
EEP_SO
V3 2
CN007 16P
LANC_IN
EEP_SCK
XCS_EEP
SWP_DIR
REG_GND
REG_GND
REG_GND
BL_GND 3 3 BL_GND
BPF_MONI
LANC_OUT
V4 1
BL_REG 2 2 BL_REG
XLANC_PWR_ON
SE_GND 1 1 SE_GND
CN404 15P
TAPE_TOP(C) 1 TAPE_TOP(C)
CN6004 24P
TAPE_END(C) 2 TAPE_END(C)
VGH/VGH 1
TAPE_LED(K) 3 TAPE_LED(K)
VSS/GND 2
TAPE_LED(A) 4 TAPE_LED(A)
9
VGL/VGL 3
REG_GND 5 REG_GND
VDD/VGLAC 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
S_REEL(-) 6 S_REEL(-)
N.C./SPS 5
S_REEL(+) 7 S_REEL(+)
GRES/EX1 6
SENSOR_VCC 8 SENSOR_VCC
FP
GPCK/MO1 7
T_REEL(+) 9 T_REEL(+)
4-2. SCHEMATIC DIAGRAMS
GSRT/MO2 8
T_REEL(-) 10 T_REEL(-)
STBYB/PSG 9
HALL_COM 11 HALL_COM
RESET/EX2 10
ME/MP 12 ME/MP
10
VCOM/VCOM 11
REC_PROOF 13 REC_PROOF
VBC/CLS 12
HI8_MP 14 HI8_MP
COLOR
LCD901
2.5INCH
STBYB/RES 13
LCD UNIT
C_LOCK_SW 15 C_LOCK_SW
SRT/PSS1 14
CN403 22P
OE/PSS2 15
DEW 22 DEW
CLR/CTR 16
M-SW(A) 21 M-SW(A)
MCLK/CLD 17
M-SW(B) 20 M-SW(B)
HCNT/SPD 18
M-SW(C) 19 M-SW(C)
11
VR/VR 19
FG1 18 FG1
VG/VG 20
FG VCC 17 FG VCC
VB/VB 21
B: TYPE S MODEL
A: TYPE C MODEL
FG2 16 FG2
VSS/GND 22
REG_GND 15 REG_GND
CAP_W 12 CAP_W
FP
CAP_W 11 CAP_W
12
CAP_V 10 CAP_V
CAP_V 9 CAP_V
VH+ 8 VH+
CN6003 10P
HU1 7 HU1
BL_HIGH 10
HU2 6 HU2
N.C 9
HV1 5 HV1
N.C 8
HV2 4 HV2
N.C 7
HW1 3 HW1
13
ND901
N.C 6
HW2 2 HW2
BACKLIGHT
N.C 5
VH- 1 VH-
N.C 4
CN481 11P
BL_LOW 3
FE(X) 11 FE(X)
LED 2
FE(Y) 10 FE(Y)
LED_GND 1
GND 9 GND
SP2Y 8 SP2Y
SP2X 7 SP2X
14
GND 6 GND
FP
SP1X 5 SP1X
CN008 2P SP1Y 4 SP1Y
1 SP(+) GND 3 GND
4-3. PRINTED WIRING BOARDS
SP901
GND 1 GND
CN005 22P
CN402 10P
1 REG_GND
U 10 U
15
2 N.C
U 9 U
M2100/M2101 MECHANISM DECK
3 LI_3V
V 8 V
4 D_2.8V
V 7 V
5 KEY_AD0
W 6 W
6 BATT_INFO
FP
W 5 W
7 CUSTOM_LED_VDD
COM 4 COM
8 N.C
FG 3 FG
9 XCUSTOM_LED_ON
FG-PG_COM 2 FG-PG_COM
16
10 REG_GND
PG 1 PG
11 XMS_LED
12 N.C
KEY
13 MS_LED_VDD CN401 2P
BLOCK
14 KEY_AD1 LM(+) 2
15 D_2.8V LM(-) 1
LM
(CF-5100)
CONTROL
M2101: TRV228E/TRV428E
16 KEY_AD3
4-2
17 D_2.8V
17
18 KEY_AD2
19 DIAL_A
M2100: TRV128/TRV228/TRV328/TRV428
20 DIAL_B
21 REG_GND
CN006
22 XRESET
EVF_4.6V
VIDEO_IN
3.3V
CHARGE_LED_VDD
XCHARGE_LED
N.C
NSLEEP
DIG_GND
BATT_UNREG
BATT_SIG
ACV_UNREG
ACV_GND
BATT/XEXT
BATT_GND
XEJECT_SW
N.C
N.C
REG_GND
ZOOM_VR
D_2.8V
MODE_LED_VDD
XVTR_LED
XCAM_LED
XPOWER_SW
XMODE_SW
REG_GND
XS/S_SW
VSYNC
ANA_GND
HSYNC
CN053 6P
16P
CN004 8P
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
16
15
14
13
12
11
10
18
10 NC
9 NC
FP-797
8 ANA_GND
FLEXIBLE
7 DIG_GND
19
6 VIDEO_IN
BT901
LCD
B/W
UNIT
BATTERY
5 VSYNC
TERMINAL
LCD902
4 HSYNC
EVF BLOCK
KEY
3 EVF_4.6V
NSLEEP
BLOCK
2
1 3.3V
CONTROL
(SS-5100)
20
21
FRAME
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
Link
Magenta
White
Cyan
• All variable and adjustable resistors have characteristic Green
Red
curve B, unless otherwise noted.
Blue
• Signal name
XEDIT → EDIT PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
A B A=B B A
• A: B+ Line
• B: B– Line Fig. a (Video output terminal output waveform)
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
• A: VIDEO SIGNAL (ANALOG)
• A: AUDIO SIGNAL (ANALOG)
• A: VIDEO/AUDIO SIGNAL
• A: VIDEO/AUDIO/SERVO SIGNAL
• A: VIDEO/SERVO SIGNAL
• A: SERVO SIGNAL
• Circled numbers refer to waveforms. Fig.b (Picture on monitor TV)
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots When indicating parts by reference number, please
color bar chart of pattern box. They are reference values include the board name.
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Note : The components identified by mark 0 or Note : Les composants identifiés par une marque
dotted line with mark 0 are critical for safety. 0 sont critiques pour la sécurité.
Replace only with part number specified. Ne les remplacer que par une pièce portant
le numéro spécifie.
4-5
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
4-2. SCHEMATIC DIAGRAMS CD-465 BOARD
1 2 3 4 5 6 7 8 9
CD-465 BOARD
A CCD IMAGER
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
1 IC951 1 REC 2 IC951 2 REC 3 IC951 3 REC
R:REC MODE
P:PB MODE 7.6 Vp-p 22 Vp-p 7.6 Vp-p
B V V V
LND951
C954
XX
4 IC951 4 REC
22 Vp-p
R11.2/P0
R-7.2/P0
R-0.3/P0
R-0.3/P0
R-7.2
C
/P0
V
1 2 3 4 5 6 7
CN951 14P
NC
GND
CCD_OUT
V4
V3
V2
V1
V4
V3
14
13
IC951 5 IC951 7 REC
CCD IMAGER
V2 12 IC951
V1 11 ICX437AKA-43:TRV128
1.2 Vp-p
GND 10 /TRV228
/TRV328
VC-341
D (1/10) H2 9 /TRV428
H
VDD
SUB
ICX433AKA-43:TRV228E
RG
H2
H1
NC
CN151 H1 8
VL
/TRV428E
THROUGH THE RG 7
FFC-005 FLEXIBLE
FLAT CABLE 14 13 12 11 10 9 8
GND 6
(PAGE 4-9)
R1.3
/P0
R1.6
/P0
R12.6
/P0.3
R-7.7
/P0.4
R8.9/P0.1
R15.1/P0
CAM_15V 5
VSHT 4
9 IC951 q; REC
CAM-7.5V 3
GND 2
23 Vp-p
E CCD_OUT 1
C955 H
0.1u
R16.1/P0
L951 C951
100uH 22u
16V
Q951
2SC4178-F13F14-T1
8 IC951 qs REC
BUFFER
R11.2
/P0
R952 R10.5
2.4 Vp-p
C952 10 R953 C953
/P0 47u
F SIGNAL PATH
XX 10k 10V
NTSC: 9.54 MHz
PAL: 9.46 MHz
Precautions for Replacement of CCD Imager
VIDEO 6 IC951 qf REC 7 IC951 qd REC • The CD-465 board mounted as a repair part is not equipped
SIGNAL with a CCD imager.
3.6 Vp-p 3.6 Vp-p When replacing this board, remove the CCD imager from the
Y/CHROMA
old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
REC H H adjustments for the camera section.
G • As the CCD imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
05
nor exposed to strong light.
1 2 3 4 5 6 7 8 9 10 11 12 13
MCK
CL
3 IC151 qa REC/PB C164
8p X151 C166 D151
R158 R160 0.01u 1SV329(TPL3)
2
C163 0.01u
XX XX
FB151 FRQ_TUNE
3.0 Vp-p 0uH R159 R161 R164 470k (4/10)
XX XX
R163
0
NTSC: 14.318 MHz
1 IC151 5 (X151) REC/PB
C PAL: 14.187 MHz C158
R2.3/P0
4.7u 2.0 Vp-p
CN151 14P
R2.8
/P0
1.3
2.8
1.5
1.3
1.4
V4
4
∗
V4 1 IC151 qs REC/PB 1.5
V3 NTSC: 28.636 MHz
V3 2 12 11 10 9 8 7 6 5 4 3 2 1 PAL: 28.375 MHz
V2
VICK(CL)
SYSCK
VDD1
CHCK
TEST
CK
VSS2
OSCO
OSCI
VSS1
PBLK
CLPDM
V2 3 3.0 Vp-p
V1
V1 4
CK_CONT1 3
GND 5 NTSC: 14.318 MHz CK_CONT2
(6/10)
D CD-465 BOARD
CN951
H2 6 PAL: 14.187 MHz C180
XX
2.8 R1.4/P0
H1 7 13 VDD2 ID 48
THROUGH THE
FFC-005 FLEXIBLE RG 8 14 VSS3 CKCONT1 47
R2.8/P0
CAM_DD_ON
4
FLAT CABLE XSHP R2.3/P0 0
GND 9
R151 R153
15 XSHP CKCONT2 46 (6/10)
(PAGE 4-7) XX
XX XSHD R2.3/P0 R2.7/P0
CAM_15V 10 16 XSHD AVD 45 XVC_SCK
VSHT 11
VSHT C152
0.001u 17 XRS
IC151 AHD 44
R2.5/P2.8
VC_SO
XVC_SCK 5
R0.4/P0 2.8 VC_SO
CAM_-7.5V 12 18 RG VDD6 43 (6/10)
TIMING GENERATOR
2.8 R2.8/P0
GND 13
2.8
19 VDD3 IC151
CXD2444AR-T4
DSGAT 42
R0.1/P0
VC_SI
VC_SI 9
E CCD OUT 14
R1.6/P0
20 VDD4
H1
XV1
RST
41
2.8 XRST_VTR (6/10)
21 40
R1.4/P0
22 H2 SEN 39
R2.2/P0 XCS_IC_301
XCS_IC_301
XCS_IC_301 7
0.5 VC_SO
23 VSS4 SSI 38 (6/10)
2.5 XVC_SCK
24 NC SSK 37
XRST_VTR
XRST_VTR 8
C151 C153 (6/10)
R-7.7/P0.5
R-7.6/P0.4
XX XX CH_SO
R15.1/P0
R-0.3/P0
R-0.3/P0
R-7.2/P0
R-7.2/P0
R2.8/P0
CH_SO
10
XSHT
XSG1
VGAT
CH_SCK
SSO
F
VM
CH_SCK
2.6
VH
NC
V2
V1
V3
VL
V4
0
CS_CH
CS_CH (6/10)
C157 25 26 27 28 29 30 31 32 33 34 35 36
R152 2.2u ID
0
AVD
AHD
C159 C162 C165
R155 C156 XX XX V_STOP
0.1u
100k 0.22u VC_SI
R162 1M
XV1
V1
V2
V3
V4
VSHT
XSG1
G
CLP1
PBLK
ADCK
L151
10uH 11
(2/10)
MCK
AD10
AD9
AD6
AD4
AD3
AD1
AD8
AD7
AD5
AD2
MCK
H R156
XX FB152
CL
CL
AD10
C177 AD10
22u AD9
12 11 10 9 8 7 6 5 4 3 2 1 4V AD9
AD8
R0.4/P1.5
R0.8/P1.5
R0.9/P1.3
R1.2/P1.3
R1.2/P1.5
R1.2/P1.4
R1.2/P1.4
R1.2/P1.4
R1.2/P1.4
R1.2/P1.4
AD8
DVSS
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
TEST
AD7
AD7
C161 2.8 2.8 CH_SCK AD6
24 23 22 21 20 19 18 17 16 15 14 13
37 38 39 40 41 42 43 44 45 46 47 48
1u DRVDD XSCK AD6
0 CH_SO AD5
C160 DRVSS SI AD5
0.1u 2.8 CS_CH AD4
I 1.5
DVSS
ADCLK
XCE
SYSV
AD3
AD4
AD3
R157 2.8 AD2
DVDD LatchSelect AD2
C154
XX
2.8
DVDD IC152 HDRST
2.8 XRST_VTR AD1
AD1
XX R2.3/P0 S/H,AGC,A/D CONVERTER
PBLK AVSS
2.7
CLPOB
IC152
AD80013AJSTRL AVSS CL
12
XSHP R2.3/P0 2.8
XSHP AVDD (5/10)
XSHD R2.3/P0 0.9 C179
XSHD VRB
1u
R2.8/P0 1.9
CLPDM VRT 6.3V
6 IC152 eh PB
J 2.8
AVDD CMLEVEL
1.4 C176
CCD IN
0.1u
CHROMA
CLPOUT
CLPBYP
CLPREF
C155 AVDD
150 mVp-p
AVDD
AVSS
AVSS
AVSS
LINE
SIGNAL PATH XX
NC
25 26 27 28 29 30 31 32 33 34 35 36
VIDEO VIDEO
SIGNAL 5 IC152 e; REC H
SIGNAL
2.8
R1/P0
R0.8/P0
R1.5/P0
0.5
2.8
0
R1.5/P0.5
CHROMA Y/CHROMA
C173 470p
PB_C_RF 13
1.2 Vp-p C172 0.22u
(4/10)
K PB REC
C171 14
C169
C167
C168
C170
0.1u
IC_801_Y_OUT
1u
1u
1u
H 0.1u
(8/10)
05
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
SIGNAL PATH
B L302 10uH
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
ADCK
15 L303 10uH VIDEO/SERVO
C341 XX
A_2.8V
CLP1
OSD_L_ON
OSD_R_ON
OSD_P_ON
CGCK
COLOR4
COLOR3
COLOR2
COLOR1
PBLK
ID
AVD
AHD
XV1
V_STOP
XSG1
C332 SIGNAL
R338 R339 C301 R333 1u
(9/10) XX 2200 4.7u 5600
L301 10uH
R312 R334 C335
C331 1u
L304 10uH XX 220 0.1u
A_4.6V
REG_GND
R1.1/P1.4
R1.2/P1.4
R1.2/P1.4
R1.2/P1.4
R1.2/P1.4
R1.3/P1.5
R1.1/P1.3
R0.7/P1.3
R0.6/P1.3
R0.3/P1.5
R2.5/P2.8
R2.3/P0
R1.4/P0
R2.7/P0
R0.1/P0
R0.1/P0
R2.8/P0
R340
2.8
1.4
0.2
2.8
2.8
1.5
1.5
2.8
1.5
1.5
1.5
2.7
0.1
1.4
2.8
2.1
2.2
2.2
1.5
1.5
XX
C
0
L306 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163
16 IC_301_C_OUT
R0.9/P1
XX
± 5%
VDDAA9
REXT9
CBU9
DAO9
TESTDAC
VSSA9
PDVSSB
PAVSSB
PAVDDB
PDVDDB
PDVDDC
PAVDDC
PAVSSC
PDVSSC
IN_VSS3
XTALOUT
XTALIN
IN_VDD3
CCDCKL
PLLENB
ADIN0
ADIN1
ADIN2
ADIN3
ADIN4
ADIN5
ADIN6
ADIN7
ADIN8
ADIN9
DVDD5
ADCK
DVSS11
CLP1
OSD_L_ON
OSD_R_ON
OSD_P_ON
CGCK
IO_VDD5
COLOR4
COLOR3
COLOR2
COLOR1
DVSS10
PBLK
ID
AVD
AHD
XV1
VGAT
XSG1
DVSS9
VCK
DVDD4
IC_301_Y_OUT
(8/10) R313
XX
0.3
17
Q305
XX
Q306
R316 2.8 7 IC301 <xzc> REC/PB ZM_RST AD1
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162
C_OUT 2SA207800LS0
1
12k VDDAA8 SENS1 AD1
BUFFER 1 AD2
2.8 FC_RST
(8/10)
2
C311 REXT8 SENS0 AD2
C305 XX
C308 XX
R1.4/P1 230 mVp-p 2.8 AD3
D L305 0.1u
8 IC301 4 REC/PB
3
XX CBU8 TEST AD3
± 5% 0.3 IRIS_COM AD4
4
DAO8 IRIS AD4
R317 470 R1.4/P0 AD5
5
VSSAA8 TBCVD AD5
420 mVp-p H 2.8 AD6
6
VSSAA7 XTECVRST AD6
R0.3/P0 R0/P2.8 AD7
R318
7
DAO7 TESTBS AD7
220 AD8
R1.4/P0.8
C312 H 9 IC301 7 REC
8
0.1u CBU7 VCKO AD8
R319 5600 R1.4/P0 AD9
9
REXT7 DVSS8 AD9
RB302 C323 1u 2.9 EN1 AD10
54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
2200 VDDAA7 390 mVp-p EN1 AD10
E 18 AFC_F0_ADJ
2.8
VDDAA6 DIR1B
0 DIR1B V_STOP
V_STOP
(4/10)
R320 12k 1.6
REXT6
q; IC301 qf REC/PB
NTSC: 33.3 msec DIR1A
R2.4/P0 DIR1A PBLK
PBLK
11
C313 0.1u R1.4/P0.4 R2.4/P0 DIR0A ID
CBU6 PAL: 40 msec DIR0A ID (1/10)
R321 270 0.2 470 mVp-p R2.2/P0 DIR0B XSG1
DAO6 DIR0B XSG1
Q302 R0.3/P0 EN0 XV1
VSSAA6 EN0 XV1
HN4A71FK
(TE85R)
qa IC301 qj REC/PB R2.8/P0 AVD
AVD
0.8
0.8
0.8
VSSAA5 IO_VDD4
BUFFER R322 270 0.2 H 2.8 VIHD AHD
DAO5 VIHDO AHD
C339
5
6
7
8
0.2 3
0.2 2
(4/10)
RF_AGC_OUT VSSAA3
qd IC301 ef REC/PB IC301 YMO1
DIR1A
DIR1B
H 21
EVF_G/BW_Y
PANEL_VD
VSSAA2 YMI4
PANEL_VD VSSAA1 150 mVp-p YMO5
PANEL_HD
(10/10) PANEL_HD DAO1 YMI5
C318 XX 2.8
CBU1 IO_VDD3
R329 XX 0.3 qj IC301 uf REC/PB 2.8
22 PANEL_SYNC
PANEL_SYNC
2.8
REXT1 H YMO6
VDDAA1 YMI6
(10/10) 2.8 2.8 Vp-p
VDDAA0 YMO7
C307 C319 0.1u R0.2/P0 qg IC301 ta PB
I 23 XVC_SCK
XVC_SCK
VC_SO
0.1u
C320 0.1u 0
VRBAD YMI7
VSSAA0 CMI2
R0.4/P1.4
C_IN 2.8 Vp-p DVDD2
IC302
26 SYS_V
SYS_V C310 0.01u R0.3/P1.4
ATF_IN qh IC301 yh PB CMO1
1.5 CHARACTER GENERATOR
IC302
(6/10) C306
0.1u VREFOP CMI1 BU3097-04FV-E2
AFC_F0 C322 0.01u R0.3/P1.4
J Y_RF_IN 1.7 Vp-p H CMO0 XOSD_SCK 1.5 2.6 VIHD
13 14 15 16 17 18 19 20 21 22 23 24
1
VIVDO 2.8 SCLK HSYNC
AVDD CMI0 XCS_OSD 2.7 2.8 VIVDO
2
C304 R2.8/P1.4 CSB VSYNC
XTBC_V_RST AMPO NTSC: 14.318 MHz EOR_OUT OSD_SO 2.7 0 COLOR1
LCD_HOLD 390p R308 1k
3
LCD_HOLD R315 C324 R331 R2.8/P1.4 PAL: 14.187 MHz SDATA VC0
C340 XX
820 0.47u 1M INN TESTKP XRST_VTR 2.8 2.2 COLOR2
XCS_IC_301 C309 4.7u
4
XCS_IC_301 RESETB VC1
2.8 2.1 COLOR3
SCAN_PATH
PANELSYNC
MECHA_HD
MECHAFLD
ADCKCONT
TRAPCONT
OUT_VDD1
R303
5
1200
VDD VC2
MECHAVD
MCKCONT
MECHA_HD R302 R306 R309
RAMTEST
PANELHD
PANELVD
FECKOUT
IN_VDD1
IN_VDD2
IO_VDD2
0.1 OSD_P_ON
IN_VSS1
IN_VSS2
PDVDDA
PAVDDA
ATSMPL
PDVSSA
XSGRST
10k
PAVSSA
470 6800
WRHLD
JOG_VD
FECKIN
DVDD1
CSYNC
DVSS1
DVSS2
DVSS3
DVSS4
6
SDDIR BLKA
XFEON
PDET1
PDET2
PDET3
27
HSWP
JOG_VD
MUTE
OSCO
AVSS
SYSV
XSCK
XRST
OFSC
AFCC
OSCI
SWP
2.1 COLOR4
MCK
JVDI
DOP
BCK
XCS
INP
MECHA_VD
SO
7
NC VC3
SI
MECHA_VD R330
CGCK 1.4 0 OSD_R_ON
(6/10) MECHA_FLD 39k
8
OSCIN BLKB
K MECHA_FLD
ATF_SAMPLE
R307
5600
R311
100 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 CL302
9
TEST MONI
KV1870RTL-G
ATF_SAMPLE
R0/P1.4
2.8
R2.8/P0
2.8
2.8
R2.8/P1.3
R2.8/P1.3
2.8
R2.9/P1.4
1.5
R2.9/P1.4
R2.5/P1.4
2.8
2.6
0.2
0
1.4
2.8
1.3
R1.6/P1.3
1.4
2.8
R0/P0.6
2.5
1.4
2.8
R2.8/P0.2
0
2.5
2.6
0.7
2.2
2.7
0
R2.8/P0
2.8
2.8
OSD_L_ON
C302
12 11 10
XSG_V_RST VSS BLKC
XSG_V_RST
D301
1u 0
X1/2_SWP C329
1500p
X1/2_SWP 1u
SWP_DIR R2.9 4 6 R3.5
SWP_DIR TM1 TM2
/P1.4 /P2.1
TBC_VD 5 2
RB301 C327
CL301
Q304 XX C337
10k 3 1 UP04601008S0 C328
0.01u L308 XX
ATF_SAMPLE
VCO 3.3uH
PANEL_SYNC
MECHA_FLD
XCS_IC_301
XSG_V_RST
MECHA_HD
MECHA_VD
CK_CONT2
X1/2_SWP
R341
PANEL_HD
PANEL_VD
SWP_DIR
R336 1k
4
2
VC_SO
SYS_V
D302
VC_SI
C330 C334 10k C338
C333
0.1u
CK_CONT2
28 CK_CONT2 C303
0.1u
CK_CONT1
(6/10)
XRST_VTR
XRST_VTR
31
R335 1k
C336 (6/10)
XX XCS_OSD
XCS_OSD
M
XOSD_SCK
XOSD_SCK
32
OSD_SO
OSD_SO (6/10)
LCD_HOLD
VIVDO
29 FSC
N (8/10)
05
1 2 3 4 5 6 7 8 9 10 11 12
R211
6800
B C209
0.22u RB201
1k
R208
R203 470k
10 HALL_OFFSET
R212 C211 L202
C207 470k 10uH
470p 0.001u
C213
0.9
0.9
4.8
0.9
0.9
R1.4/P0.2 1.2 XX
D202 C203 7 6 5 4 3 2 1
C
C202
0.01u 1SS355TE-17 4700p
C217
4.7u
C218
0.1u 33
OUT2
IN2-
IN2+
Vcc
IN1+
IN1-
OUT1
(4/10)
IC202
IRIS DRIVE
HALL BIAS CONTROL
HALL GAIN CONTROL
HALL AMP
OUT3
OUT4
IN3+
IN4+
GND
IC202
IN3-
IN4-
LM224PT
D 8 9 10 11 12 13 14
R1.9/P2.8
R1.4/P0.2
R1.4/P0.1
0.1
0.1
0.7 R215
R0.9
/P0 10k
HALL_GAIN
R209 470k
Q201 R1 C206
RN1119FV(TH3SONY) /P0 0.1u R214
IRIS DRIVE
0.1 1k
R207
C219 220k
XX R205 R206 0.6
2200 10k
Q203
C204 R204 C205
E CN201 24P
IRIS_DRIVE(+)
R218
XX
4.7u 1M 0.1u R213
330
2SC5658T2LQ/R
HALL GAIN
24 CONTROL
IRIS_HALL(+) 23
D203 C212 C215
IRIS_BIAS(+) 22 0.47u 2200p
XX
IRIS_HALL(-) 21
C214 R216
IRIS_BIAS(-) 20 0.01u 47k
IRIS_DRIVE(-) 19
TEMP 18 RB202
F TEMP 17
22k
ZM_SENSE_VCC 16 A_4.6V
ZM_SENSE_OUT 15 RB203 D_2.8V
47k C216 R217
LENS_DET 14 XX XX 34
FC_SENSE_VCC 13 REG_GND
LENS BLOCK (9/10)
FC_SENSE_OUT 12 REG_GND (MT_GND)
2.8
GND 11 MT_5V
1 4
ZOOM_A 10 IRIS_PWM
2.8 2.8
G ZOOM_B 9 Q202
UP04116008S0
2 5
FC_RST_LED
ZOOM_XB 8 6 3
SENSOR SWITCH
ZOOM_XA
IR_SWITCH
7
R0.8/P0 R0.9/P0
ZM_RST_LED
35
6 LENS_DET
(6/10)
IR_SWITCH 5 XNS_SW
FOCUS_A 4 HALL_AD
FOCUS_B 3 LENS_TEMP_AD
FOCUS_XB 2
H FOCUS_XA 1
R3.1/P0.2
R0/P2.8
/P2.8
R2.4
2.8
0.2
0.2
0.2
5
0
I 24 23 22 21 20 19 18 17 16 15 14 13
C208
0.01u
VDD
OUT1B
PGND
OUT2B
VM23
OUT3B
PGND
OUT4B
EN4
IN4
EN3
IN3
IRIS_COM
ZM_RST
IC201 C210
FC_RST
DIR1B
47u
FOCUS/ZOOM
MOTOR DRIVE 6.3V DIR1A 30
OUT 1A
OUT2A
OUT3A
OUT4A
IC201
PGND
PGND
EN1 (2/10)
VM4
VM!
UPD16877MA-6A5-E2
EN1
EN2
IN1
IN2
EN0
J 1 2 3 4 5 6 7 8 9 10 11 12 DIR0A
DIR0B
5
R0.8/P0.2
0.3
0.3
0.3
5
R1.5/P2.8
0
R0.2/P2.8
05
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SIGNAL PATH
ws IC481 6 REC
VC-341 BOARD (4/10) wa IC481 9 PB w; IC481 qa PB VIDEO SIGNAL
AUDIO VIDEO/AUDIO/
VIDEO/SERVO
A REC/PB AMP (RF BLOCK,ER BLOCK)
400 mVp-p
CHROMA Y Y/CHROMA SIGNAL
SERVO
SIGNAL SIGNAL
400 mVp-p 150 mVp-p
XX MARK:NO MOUNT NTSC: 33.3 msec
NO MARK:REC/PB MODE PAL: 40 msec REC
NTSC: 33.3 msec
R:REC MODE PAL: 40 msec H
P:PB MODE
PB
L483
B ET481 C493
22uH REC REC/PB PB
XX 0.1u C498 4.7u
C502 XX
Ref.signal
C499 XX
± 0.5%
C501
C504
XX
R493 C496 XX
ET482 0.01u
2700
XX
R495 150k
R4.5/P3.5 3.9
220uH
L481
Q485
C513 UNR31A500LS0
0.47u
C
R0.5/P0.3
R0.1/P1.9
SWITCH 4.7
R0/P2.8
2.3
0.6
0.4
2.2
R2.5/P0.1 0
24 23 22 21 20 19 18 17 16 15 14 13 0
AGC_SLOW
C482
VPSW1 OUT
RAMP V1
REC1 IN
RAMP IR
MT_Q
MTIN
CARDET
PCMOUT/MTSW
MT_F0
PBRFOUT
RP_PB
VCC
C481
33u
M2100/M2101
4.7
0.01u Q484
6.3V RB482
R3.1/P4.4
UNR32A300LS0
MECHANISM 470k
AGC SLOW
0.01u
C483
DECK(1/2) R487
27k
RP_PB_MODE
D
R0.9/P0 2.5
37
36 35 34 33 32 31 30 29 28 27 26 25
10 11 12
REC DUMP1 DOC_DET DOP
R0/P1.3
GND CLPFOUT (6/10)
VIDEO HEAD 4.6 R4.5/P3.5 C509
CN481 11P REC1 OUT AGC TC BOTH_REC
FB481 C488 0.01u 4700p
0.7 R1.5/P2
PB1 IN RF AGCOUT XFE_ON
9
GND 1
4.6 R2.2/P2.4
VCC AMP RP_IR
8
GND 2
C486 0.022u R488 220 2.6
PB DUMP1 IC481 DOP
0
RF_SWP
7
GND 3
C487 0.022u R489 220 2.6 REC/PB AMP 2.2
PB DUMP2 Y/C/ATF IN
6
CH SP1Y 4
SP1 1.1 IC481 0
C484 BIASADJ YLPFOUT/CARDETOUT C508
5
SP1X 5 0.01u CXA3265R-T4 C507
FB482 C489 0.01u 0.7 2.6 0.01u
0.001u
E PB2 IN Y MIX
4
GND 6
4.6 R3.6/P0.8 C514
REC2 OUT REC_Y/MT_CONT
3
CH SP2X 7 0.01u
SP2 4.7
GND VCC3
2
SP2Y 8
BOTH_REC/DV PBPS
R0.9/P0 0
REC DUMP2 AFM IN
1
GND 9
R484 C515
REC_L_CONT
FLYNG FE(Y) 10 DOP
RAMP CONT
VSSW2 OUT
27k 0.01u
ERASE
19
RAMP V2
PCM REC
FE(X) 11 C510 REC_RF
REC2 IN
PCM IN
AFREC
XX
RAMP
PB_C_RF
SWP
GND
(2/10)
C511 RF_AGC_OUT
F M2100: TRV128/TRV228/TRV328/TRV428
M2101: TRV228E/TRV428E 37 38 39 40 41 42 43 44 45 46 47 48
XX
R2.5/P0.1
0.5
R3.1/P4.7
0
1.4
3.3
ql IC481 wj,ef> PB
C505
R494 0.01u
2700 16V
6.1 Vp-p C494 C497
0.1u 0.01u
Q481 R3.8/P4.7
5
0
2SA1965-S-TL
Q481-483 Q483 R1.4
2
PB_RF 39
ERASE HEAD OSC 1 /P2.4 C495 REC_2
R482 UP04601008S0 3 (10/10)
560 R1.2/P2.8 100p
I
VC_SO
XVC_SCK
VC_SO
40
IC251 XVC_SCK
(6/10)
EVR
(D/A CONVERTER) DA_STRB
IC251
BH2222FV-E2
DA_STRB 42
(6/10)
4.8 2.5 XVC_SCK HALL_GAIN
15 16 17 18 19 20 21 22 23 24 25 26 27 28
RP_4.6V
1
A_4.9V(VCC) CLK
J A_4.6V
4.8 0.5 VC_SO HALL_OFFSET
HALL_GAIN
33
2
A_4.9V(VDD2) DI
FB252 R3.6/P0.8 2.4 HALL_OFFSET
HALL_REF
3
REC_Y/MT_CONT DOC_DET
0uH
3.3 3.9 HALL_REF (3/10)
4
REC_L_CONT RF_AGC_CONT
2.2 2.3
FRQ_TUNE
2
5
MT_F0 RP_IR
4.7 2.1 AFC_F0_ADJ FRQ_TUNE
6
XRF_AGC_OFF AFC_F0_ADJ
4.7 2.5 FRQ_TUNE (1/10)
7
XMP/ME FRQ_TUNE
1.1
8
CFG_DUTY REC_BIAS
36 C252
4.7u 1.5M_DEV 0.8 0.5 AFC_F0_ADJ
18
9
AU_BPF HALL_REF
0.8 HALL_GAIN
K FB251 A_FADE 0
BEEP_EVR
A_FADE
HALL_GAIN
HALL_OFFSET
1.2 HALL_OFFSET
0uH
2.9 1.4
AU_2.8V D_3.2V(VDD1) SWP(SEL)
0 DA_STRB
C251 GND STB(LD)
1u
05
REG_GND
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
(6/10) CAP_U
CAP_ON
wf IC401 yd,yg,yk REC/PB
R401
C 47k
1.4 Vp-p
HI8_MP_SW
HI8_MP_SW
0.5
0.5
0.5
0.2
0.2
0.8
1.5
0.8
1.5
REC_PROOF C404
REC_PROOF FB401 2.8 1 1 0 0.8 NTSC: 180 Hz
M2100 ME_SW
ME_SW
0.1u
PAL: 150 Hz
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
/M2101 C407 DRUM_COM
MECHANISM
CAPON
NC
C_W
C_VS
C_V
C_VS
C_U
L_PGND
L_OUT2
NC
L_VM
L_OUT1
D_W
D_VS
NC
D_V
D_VS
D_U
NC
NC
0.001u RB401
50V 10k
DECK (2/2) C434 C437
44 XCC_DOWN
XCC_DOWN 0.001u 0.001u
D M2100:TRV128
/TRV228
(7/10) CAP_FWD 2.8
wg IC401 td REC/PB
/TRV328 wd IC401 4 REC/PB
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
C_FRC D_PGND
1
/TRV428 0.8
0.001u
C401 TEST COM
C433
M2101:TRV228E 0.1u LM_- MR_VCC 2.8 0.8
2.8 Vp-p
/TRV428E CN401 2P VMR 2.8 Vp-p WIN
3
CAP_FG 1.4 0.8
M903
M CFGOUT VIN
4
LOADING LM(-) 1 NTSC: 180 Hz
LM_+ 0.8
MOTOR C_PGND PAL: 150 Hz
NTSC: 820 Hz UIN
5
LM(+) 2 R406
0.8 C431
C402 C403 XX GND PAL: 1148 Hz DFILTER
6
XX XX 0.047u
FG1 1.4 2.1
CN402 10P CFGIN+ DFC C435
7
DRUM_PG_SENS FG2 R0/P1.4 1.4 2.2u DRUM_FG
E CFGIN- DFGOUT
8
PG 1
FG_PG_COM 0.4 1.3 R424 10k DRUM_FG_SENS
C410 CAGC DFGIN
9
FG-PG_COM 2 1u
FP/PG DRUM_FG_SENS UHE+ 0.6 1.3 R430 XX R416 C442 FG_PG_COM
IC401
20 19 18 17 16 15 14 13 12 11 10
FG 3 U+ VREF XX 470p
DRUM_COM UHE- 0.6 0.1 DRUM_PG
COM 4 U- PGOUT
VHE+ 0.4 DRUM/CAPSTAN/LOADING 1.3 DRUM_PG_SENS
W 5 V+ MOTOR DRIVE PGIN
DRUM_W VHE- 0.4 IC401 0.9
V- PGC R431
W 6 TB6550FG(O,EB)
C429 1u 0
WHE+ 0.2 13.6
V 7 W+ VG
M901 DRUM_V WHE- 0.2 0.1 C430 0.022u C441 R425
W- ISNF C443
DRUM V 8
F MOTOR 2.8
VCC1
wh IC401 t; REC/PB DBOUT
0.6
1u 0.1u
R418
XX
0.01u
U 9 XX
C408
16V
U 10
DRUM_U
HE_VCC
0.7
1.3
VH
2.8 Vp-p
DBIN
0.6
DRUM_ERROR 46
0.3
TOPIN CBLOUT CAP_ERROR (9/10)
TAPE_TOP 2.8 0.3 R423
TOPOUT CBOUT
XX
TAPE_TOP_C 1.3
ENDIN
NTSC: 33.3 msec CBIN
0.3
CN403 22P TAPE_END_C PAL: 40 msec C440
XX
VH- 1
WHE- C409 CL
12
ENDOUT
LIMOUT
XRESET
RLDO1
RLDO2
HW2 2 0.047u
TRV228E/TRV428E
DGND
RLM1
RLM2
(1/10)
RLO1
RLO2
RLP1
RLP2
VCC2
DEC1
DEC2
MCK
WHE+ 10V
CSR
SCK
XCS
HW1 3 TAPE_END
G
SI
VHE-
0.022u
HV2 4
C428
VHE+ 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
HV1 5
2.8 ∗ ∗
1.9
1.9
1.9
1.9
8.3
0.2
0 0
2.8
1.5
2.5
2.8
0.5
UHE- 0.5
HU2 6
UHE+ S_REEL_+
HU1 7
HE_VCC C411
VH+ 8 S_REEL_- 0.01u UNLOAD
MECHANISM
CAP_V
CAP_V
9
10
CAP_V
SREEL_FG
T_REEL_+
LOAD
XCS_IC-401
47
BLOCK C412 DRUM_PWM
(6/10)
CAP_W 11
H (CAPSTAN MOTOR)
(PAGE 4-33) CAP_W 12
CAP_W T_REEL_- 0.01u
TRV228E/TRV428E CAP_PWM
TREEL_FG R413 R427
CAP_U 13 C427 R426 C445
CAP_U C446 C426 4700p 15k 0.01u
CAP_U 14 XX 0.01u
REG_GND 15
FG2 R414 C444
FG2 16
MR_VCC
0.01u
VC_SO 48
FG VCC 17
FG1 XVC_SCK (6/10)
FG1 18 C414 C423
C416
C418
C419
C421
C422
XX
XX
XX
XX
XX
XX
MODE_SW_C 0.1u R413,R427
I M-SW(C) 19
MODE_SW_B wj IC401 rf REC/PB wk IC401 ra REC/PB 0 :TRV128/TRV228/TRV328/TRV428
M-SW(B) 20 10k :TRV228E/TRV428E
MODE_SW_A
M-SW(A) 21
DEW_AD 80 mVp-p 70 mVp-p R414
DEW 22 15k :TRV128/TRV228/TRV328/TRV428
DRUM_FG 47k :TRV228E/TRV428E
DRUM_FG
DRUM_PG
DRUM_PG 13 sec 13 sec
TAPE_TOP
TAPE_TOP
TAPE_END
TAPE_END XRST_VTR
50
SREEL_FG
J CN404 15P
XCC_DOWN TREEL_FG
SREEL_FG
45 (6/10)
C_LOCK_SW 15 TREEL_FG
HI8_MP_SW CAP_FWD (6/10)
HI8_MP 14 CAP_FWD
REC_PROOF 13
REC_PROOF CAP_FG
CAP_FG LM_LIM_DET
51
ME_SW CAP_ON
ME/MP 12
R404
CAP_ON (6/10)
270
HALL_COM 11 XREEL_HALL_ON
T_REEL_-
TAPE_LED_ON
SIGNAL PATH
T_REEL(-) 10
T_REEL_+
T_REEL(+) 9
MECHANISM R403 470 REC REC/PB PB
K BLOCK SENSOR_VCC 8
S_REEL_+
R409
82
91
(SENSOR) S_REEL(+) 7 CAP_FG
(PAGE 4-33) S_REEL_-
(10/10) Drum speed servo
S_REEL(-) 6
REG_GND 5
TAPE_LED(A) 4
Drum phase servo
TAPE_LED(K) 3
TAPE_END_C 4.4 R405 Drum servo(speed and phase)
TEPE_END(C) 2 0
TAPE_TOP_C 0
TAPE_TOP(C) 1 Q401
Capstan speed servo
L UNR32A600LS0
LED DRIVE
C405
XX
C406
0.1u
05
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
NO MARK:REC/PB MODE
VC-341 BOARD (6/10) R:REC MODE
P:PB MODE
A CAMERA/MECHA CONTROL ∗:IMPOSSIBLE TO MEASURE THE
VOLTAGE AT THE MARKED POINTS.
XX MARK:NO MOUNT
XNS_SW AA_2.8V
XNS_SW
ZM_RST_LED
ZM_RST_LED D_2.8V
FC_RST_LED FB601 0uH 66
35 FC_RST_LED
IRIS_PWM
D_1.5V
REG_GND (9/10)
IRIS_PWM
B (3/10)
LENS_TEMP_AD
LENS_TEMP_AD
HALL_AD
HALL_AD
LENS_DET
XREEL_HALL_ON
HI8_MP_SW
REC_PROOF
ME_SW
MODE_SW_C
MODE_SW_B
MODE_SW_A
OSD_V
VIVDO
TBC_VD
MECHA_VD
DOP
BEEP
TAPE_LED_ON
DRUM_PG
DRUM_FG
IR_ON
CAP_FG
XS_JACK_IN
AV_JACK_IN
SYS_V
XTBC_V_RST
REC_CRRT1
REC_CRRT0
XCS_MC_FLASH
MECHA_HD
XFE_ON
RP_PB_MODE
BOTH_REC
CAP_FWD
CAP_ON
LCD_HOLD
LENS_DET
0.1u
EVF_DD_ON
C624
EVF_DD_ON RB611
AV_JACK_IN 100k
53 AV_JACK_IN
XS_JACK_IN CL602 CL618
RB613
R636 100k
4700
XS_JACK_IN
CL604
CL605
CL606
(10/10) CUSTOM_LED_ON C610 RB605
CUSTOM_LED_ON 1k
C607 0.1u
DCOUT_JACK_IN XCS_EEP 2.8 2.8
0.1u
C DCOUT_JACK_IN
8
S VCC
EEP_SI 2.8 2.8
7
Q HOLD
VST_C_RESET 2.8 2.8 EEP_SCK
VST_C_RESET
6
W C
CL614
54 PITCH_AD 0 EEP_SO
R2.8/P0.2
R1.8/P2.8
PITCH_AD
5
VSS D
R0/P2.8
R0/P2.8
R0/P2.8
R0.3/P0
YAW_AD
(10/10) YAW_AD
1.4
2.8
2.6
2.8
2.8
0.1
1.3
1.5
1.4
2.8
2.8
2.5
1.4
2.8
2.8
2.8
2.8
2.8 0 0 0 0 0 0 0 0 0 0 0 0
216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 IC602
55 BEEP
BEEP
C602 EEPROM
VDD
XREEL_HALL_ON
HI8_MP_SW
REC_PROOF
ME_SW
MODE_SW_C
MODE_SW_B
MODE_SW_A
IC_701_V
EXI_TEST
MEM_VD
TBC_VD
MECHA_VD
DOP
MELODY_CARR
TAPE_LED_ON
VSS
SDC_ON
DRUM_PG
DRUM_FG
IR_ON
SREEL_FG
TREEL_FG
VDD
CAP_FG
HP_JACK_IN
XS_JACK_IN
V_JACK_IN
MIC_IN
XMIC_MONO
VSS
SYS_V
TBC_V_RESET
INTVD
REC_CRRT1
REC_CRRT0
XCS_MC_FLASH
MECHA_HD
XFE_ON
RP_PB_MODE
BOTHREC
VDD
CAP_FWD
CAP_ON
LCD_HOLD
IC602
D (8/10)
10p
HN58X2532TI
C619
0.01u
UNLOAD
20MHz
UNLOAD
(D_1.9V)
(D_2.8V)
X601
R606
(D_2.8V)
LOAD XX 1.2 R2.8/P0 CAM_DD_ON
LOAD 1 X1 CAM_DD_ON 162
47 XCS_IC_401
XCS_IC_401
2 VSS 161
C623
0.1u 67
DRUM_PWM ∗ 1.5 LCD_HOLD
(5/10) DRUM_PWM 3 X0 (D_1.9V) VDD 160
CAP_PWM C603 10p 1.5 RF_SWP (10/10)
CAP_PWM 4 XIN RF_SWP 159
1.4 SWP_DIR
R605 XX
5 MD2 wl IC601 1 (X601) REC/PB e; IC601 <zb,> REC/PB SWP_DIR 158
1.6 X1/2_SWP
MECHA_FLD
MECHA_FLD
E 51 LM_LIM_DET
LM_LIM_DET
R601
6 MD1
2.9 Vp-p
X1/2_SWP(HSWP) 157
R0/P0.6 ATF_SAMPLE
LCD_HOLD
LCD_HOLD
100 7 MD0 1.9 Vp-p ATF_SAMPLE 156 AFC_F0
(5/10) XSYS_RST 2.8 0 JOG_VD AFC_F0
8 XINIT JOG_VD 155 VIVDO
R602 10k 2.8 2.8 XSG_V_RST VIVDO
TREEL_FG 9 XRST 20 MHz NTSC: 33.3 msec XSG_V_RST 154 XTBC_V_RST
TREEL_FG DOP 0 XTBC_V_RST
SREEL_FG 10 DOP
PAL: 40 msec 153 XCS_IC301
SREEL_FG AGC_SLOW 0 XCS_IC301
TAPE_TOP
TAPE_TOP
C601
11 AGC_SLOW 152
2.8
C622
0.1u MECHA_HD
MECHA_HD
27
TAPE_END 0.01u 12 (D_2.8V) VDD 151 JOG_VD
TAPE_END R0/P2.6 JOG_VD (2/10)
16V C615
DRUM_FG 13 C2 150 0.1u MECHA_VD
F 45
DRUM_FG
DRUM_PG
DRUM_PG
2.8
0.2
14 VDD (D_2.8V) VSS 149 ATF_SAMPLE
MECHA_VD
ATF_SAMPLE
LM_LIM_DET C605 0.1u
XREEL_HALL_ON 15 LM_LIM_DET TUL 148 XSG_V_RST
(5/10) XREEL_HALL_ON XCS_IC_401 2.8 2.8 XSG_V_RST
TAPE_LED_ON 16 XCS_IC_401 (D_2.8V) AVDD_U 147 X1/2_SWP
TAPE_LED_ON UNLOAD 0 2.8 X1/2_SWP
CAP_FWD 17 LM- (D_2.8V) AVRH_U 146 SWP_DIR
CAP_FWD LOAD 0 SWP_DIR
CAP_FG 18 LM+ AVSS_U 145 TBC_VD
CAP_FG TAPE_TOP 2.8 TBC_VD
CAP_ON 19 TAPE_TOP ANIN1 144
CAP_ON TAPE_END 2.8
20 TAPE_END ANIN0 143 XCS_OSD
MODE_SW_A
MODE_SW_A 21 VSS 142 XOSD_SCK
XCS_OSD
XOSD_SCK
32
R005
G MODE_SW_B
MODE_SW_B 22 141 R005 100k :TRV128/TRV228
22k :TRV228E
OSD_SO
OSD_SO
(2/10)
MODE_SW_C 23 140 56k :TRV428E
43 MODE_SW_C
ME_SW 24 LM_LIM_CONT DRUM_START 139
XX :TRV328/TRV428
(5/10)
ME_SW
HI8_MP_SW 25 F_RATE IC601 DRUM_ON 138
R006
47k
R006
:TRV128/TRV228
VC_SI
VC_SI
9 25 94
HI8_MP_SW EVF_DD_ON 0 100k :TRV228E
REC_PROOF 26 EVF_DD_ON CAMERA/MECHA CONTROL XDRUM_BRAKE 137 10k :TRV328/TRV428 (1/10) (2/10) (10/10)
REC_PROOF IC601 68k :TRV428E
DEW_AD 27 XCS_EVF MB91194APFF-G-153-BNDE1 SYSTEM_AD 136 XCS_IO
DEW_AD 0
28 XEVF_TALLY GRNERAL_AD 135
1.4 MECHA_FLD VC_SO
56 (10/10) V_LIGHT_PWM
V_LIGHT_PWM 29 V_OUT_ON MECHA_FLD 134
1.5 ZOOM_VR_AD XVC_SCK
VC_SO
5 23 40 48 81 95
H 30 ZOOM_SW_AD 133
2.8 R616 TRV328/TRV428/TRV428E
XVC_SCK
(1/10) (2/10) (4/10) (5/10) (8/10) (10/10)
31 XCS_IO 132 1k RB610
ZOOM_VR_AD 32 (XUSB_EN) 131 C612 4700
57 (10/10) ZOOM_VR_AD
33 YAW_AD 130
1.3 RB608 1M XX YAW_AD
1.2 PITCH_AD
C604
0.1u
0
34 VSS PITCH_AD 129
R1.4/P0.3 HALL_AD XCS_IC301
7
OSD_V 35 C1 IRIS_HALL_AD 128
58 (7/10) OSD_V 1.5
36 VDD (D_1.5V) LENS_TEMP_AD 127
1.9 R619 1k LENS_TEMP_AD (1/10)
C616 0.1u C625
C606 XX
37 AVSS_1 126
0.1u
I 38 (D_2.8V) AVRH_1 125
2.8
2.8
C617 C618
C617,C618
4 89 CAM_DD_ON
CAM_DD_ON C620
0.1u
39 (D_2.8V) AVDD1 124
2.8 C614
100k (Note):TRV128/TRV228/TRV228E
0.01u :TRV328/TRV428/TRV428E
40 (D_2.8V) AVDD_0 123 1u
(1/10) (9/10) 2.8 Note:Resistors are mounted to
41 (D_2.8V) AVRH_0 122 the location where C617
and C618 are printed.
42 AVSS_0 121 (TRV128/TRV228/TRV228E only)
∗
DCOUT_ON 43 SREEL_FG_AD 120
59 (9/10) DCOUT_ON LENS_DET 0
44 LENS_DETE TREEL_FG_AD 119
∗ SREEL_FG
0 TREEL_FG
45 DEW_DET 118
DA_STRB 0 R2.9/P1.4 DEW_AD
J 60 (10/10) XCS_LCD
XCS_LCD 46 DA_STRB AFC_F0_IN 117
AFC_F0
47 CK_NISHIKI 116 CL616
0 DCOUT_ON
48 DCOUT_ON 115
ZM_RST_LED 2.8
49 ZM_RST_LED HITEST 114 CL613
FC_RST_LED 2.8
8 31 50 XRST_VTR
XRST_VTR 50 FC_RST_LED USB_DET 113 IR_ON
IR_ON
68
51 XUSB_ON 112
(10/10)
ATF_DEBUG_IN/EVF_VG_AD
EEP_SCK (MC_FLASH_SCK)
ATF_DEBUG_PWM2
VST_C_RESET
(D_1.9V)
(D_2.8V)
0 2.8 XCS_LCD
K
APOLLO_PWCTRL
ATF_DEBUG_IN2
SYS_V
V_LIGHT_PWM
MELODY_ENV
IC_701_XSCK
XCS_AFM_ST
DRUM_PWM
XCS_APOLLO
GCAM_XSCK
XCS_IC_701
XCS_IC_301
XCS_GCAM
IC_701_SO
(2/10) (7/10)
IRIS_PWM
CK_CONT1
CK_CONT2
CAP_PWM
xRST_VTR
IC_701_SI
GCAM_SO
OSD_SCK
XCS_OSD
xCS_AFM
XCS_EEP
OSD_SO
SCK_VC
VC_SO
VC_SI
OSC1
OSC0
IC_701_SCK
VDD
VDD
VSS
VSS
VSS
61
IC_701_SCK
XCS_IC_701
XCS_IC_701 XCS_AU
RF_SWP
XCS_AU
69
IC_701_SI 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 (8/10)
(7/10) IC_701_SI
IC_701_SO 2.8
2.9
2.8
2.5
2.8
2.8 0
2.8
2.8
2.5
2.2
0.7
2.6
1.5
1.5
2.7
2.7
2.8
2.8
0
2.8
0.9
0.5
0 0
R2.8/P0
R0/P2.8
2.8
IC_701_SO
CL610
CL617
CL612
CL611
L
XCS_IO
XCS_IO
70
62 XSYS_RST
XSYS_RST
(8/10)
XFE_ON
10k
RF_SWP CL609
93 REC_CRRT0
REC_CRRT0
REC_CRRT1
RB603 BOTH_REC
RF_SWP
BOTH_REC 37
100k
(10/10) REC_CRRT1 DOP
SIGNAL PATH DOP (4/10)
RB612 AGC_SLOW
47k AGC_SLOW
M EEP_SI
RB601
100k REC REC/PB PB
RP_PB_MODE
RP_PB_MODE
63 EEP_SI
EEP_SO
(10/10)
EEP_SO
EEP_SCK Drum speed servo
DA_STRB
DA_STRB
42
EEP_SCK
(4/10)
CS_CH
64 CS_CH
DRUM_PWM
10
IC_701_SCK
XCS_IC_701
XCS_IC_301
IC_701_SO
XOSD_SCK
MD2 ( REG_GND
XRST_VTR
IRIS_PWM
CK_CONT1
CK_CONT2
)
CAP_PWM
CH_SCK
IC_701_SI
XCS_OSD
XVC_SCK
EEP_SCK
XCS_EEP
CH_SCK
EEP_SO
XCS_MC_FLASH
EEP_SI
CH_SO
VC_SO
CS_CH
(10/10) CH_SO
VC_SI
(1/10)
N CH_SO
(10/10) SWP_DIR
SWP_DIR Capstan servo(speed and phase) CK_CONT2
CK_CONT1
3 28
05 CK_CONT2
(1/10) (2/10)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
XCS_DD
XSYS_RST
SIRCS_PWM
BATT_SIG
SIRCS_SIG
R:REC MODE
P:PB MODE
74
(9/10)
B
R715
R708 EVER_3.0V
1k
1M BATT_IN
± 0.5% Q701
BATT_IN
HN1L02FU(TE85R) XRESET
XRESET
BATTERY CHARGE VTR_DD_ON
R710 DETECTOR
470k 3 VTR_DD_ON
± 0.5% XCS_DD
XCS_DD
1 4 HI_EVER_SO
HI_EVER_SO
0.3 2.7 HI_EVER_SCK
HI_EVER_SCK
R707 2 5
1SS355TE-17
100k
± 0.5% C713 6 3
0.01u 0 0
C 16V
XRESET 85
(10/10)
RB708
D701
R711
100k
C708
22u ± 0.5%
47k
XSYS_RST
XSYS_RST
62 92
6.3V
(6/10) (10/10)
C712 C714
18p 18p
SYS_V
SYS_V 75
32.768kHz
D
X702
(6/10)
R713
0
KEY_AD0
R709
XCC_DOWN
XCC_DOWN
44
R2.8/P1.5
KEY_AD1 2.8 10M
(5/10)
KEY_AD2
2.8
2.8
2.7
2.5
1.3
2.8
0.3
0.3
0.3
3
1
3
KEY_AD0 KEY_AD3 RB704
KEY_AD0
1k 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 BATT_UNREG
KEY_AD1
KEY_AD1
KEY_AD2 VTR_UNREG
KEY_AD1
KEY_AD0
HOT_SHOEID2
HOT_SHOEID1
VTR_DD_SENSE
ACV_SENSE
BATT_SENSE
VCC
X0A(IN)
X1A(OUT)
GND
XCS_DD
TP_SEL2
XSYS_RST
XLANC_ON
SIRCS_OUT
XDS_RST
IB_SI
IB_SO
XSIRCS_IN
KEY_AD2
E 71 KEY_AD3 D_2.8V
C707
C705
C702
C703
XX
XX
XX
XX
KEY_AD3
XBATT_INFO_SW
XBATT_INFO_SW
(10/10) DIAL_A
DIAL_A C711 0.3 LANC_OUT
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
DIAL_B R712 0.1u KEY_AD2 LANC_OUT
DIAL_B 10k 2.8
3
VCC
es IC701 ta (X702) REC/PB
LANC_IN
0.3
3
LANC_IN
76
INIT_CHARGE_ON
AVREF INIT_CHARGE (9/10)
3 0 FAST_CHARGE
GND FAST_CHARGE
RB701 3.0 Vp-p BATT_SIG
470k KEY_AD3 LCD_COM/XDATA BATT_SIG
F 2.8
KEY_AD4 VTR_DD_ON
3 VTR_DD_ON BATT/XEXT
BATT/XEXT
KEY_AD5 32.768 kHz FAST_CHARGE
XEJECT_SW KEY_AD5 TP_SEL1 FAST_CHARGE
XEJECT_SW KEY_AD7 2.8 2.8 INIT_CHARGE_ON
XPOWER_SW KEY_AD6 XHI_DS_HELP INIT_CHARGE_ON
XPOWER_SW 2.4 SYS_V
XMODE_SW KEY_AD7 (XS/S_SW) SYS_V
C701 C704
XMODE_SW
KEY_AD7
KEY_AD7 RB703
1k
XX XX
2.7
TP_X IC701 BATT_IN
3
C715
R717 470
R718 100k
BATT_IN
72 KEY_AD5
KEY_AD5 TP_Y HI CONTROL
IC701
TEST
1.3
0.1u X701
10MHz
XCHARGE_LED R704 47k XLANC_JACK_IN X_TAL
(10/10) MB89097PFV-G-170-BND-ERE1
XCHARGE_LED XRESET 1.2
XVTR_LED RST_X X_TAL
XVTR_LED BATT/XEXT C709 0.01u 3
G XCAM_LED
XCAM_LED
0
BATT/EXT TEST R716
1M XCS_IC_701
SHOE_ON IC_701_XCS0
C710
4700p 2.5 IC_701_SCK
STROBO_PLUNGER IC_701_SCK0
R705 2.8 IC_701_SO
XX NEW_DD IC_701_SO
3 2.8 IC_701_SI LANC_IN
R706 LANC_IN
CHRGELED/LCD_LED_ON
DD_COM/XPRD IC_701_SI
DIAL_A XX R3/P2.6
DIAL_A XCS_LCD_DRIVER
2.8 LANC_OUT
LANC_OUT
77
XLANC_POWER_ON
XF_TALLY_LED 0 3
XPOWER_SW
XBATT_VIEW
XF_TALLY_LED HI_EVER_SO
XMODE_SW
XEJECT_SW
SYS_V_OUT
BT_LED_ON
XCC_DOWN
73
XMEM_ON
H SIRCS_PWM
MEM_LED
PWR_LED
CAM_LED
SIRCS_PWM
F_TALLY
(10/10) SIRCS_SIG
SIRCS_SIG ea IC701 wk (X701) REC/PB
GND
VCC
N.C
IC_701_SCK
IC_701_SCK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2.1 Vp-p IC_701_SO
IC_701_SO
61
0
2.9
2.9
2.9
0
3
R1.4/P0.1
R0/P2.5
R2.3/P2
R0/P2.3
2.6
2.9
IC_701_SI
IC_701_SI
10 MHz XCS_IC_701 (6/10)
XCS_IC_701
I
RB705
1k
XPOWER_SW
OSD_V
OSD_V 58
XMODE_SW R714
(6/10)
4700
XBATT_INFO_SW
XLANC_PWR_ON
XF_TALLY_LED
XCHARGE_LED
XEJECT_SW
HI_EVER_SO
XCAM_LED
XCC_DOWN
XVTR_LED
RB706
OSD_V
J 1k
05
1 2 3 4 5 6 7 8 9 10 11 12 13
C828
0.01u
C831
4700p
C833
0.22u
R814 C825
C830
C826
C834
1u
1u
1u
22u C836 C839
(9/10) MT_5V XX
6.3V 0.22u 0.47u PB
REG_GND
C819 C817 C823
0.22u 10u 1u
16V C822
0.22u
55 R817
(6/10)
BEEP
C811
4.7u
C813
XX
C815
22u
470k
REC_AFM
80
R3.4/P0.1
6.3V
(10/10)
C
CONTROL CN008 2P
2.4
2.4
2.4
2.4
2.9
1.4
1.4
1.4
1.4
0.7
0.7
1.1
0 R1.1/P2
KEY SP(+) 1
BLOCK
SP(-) 2
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
FSC
29
(CF-5100)
SP_VCC
SP_VREF
BEEP_IN
SP_IN
SP_OUT
DAC
VCC(AFM)
NR_VRF
NR_EMP
LS_WAIT1
LS_WAIT2
NR_HOLD
NR_RECOVER
GND(NR)
PLL_LOOP_F
RECAFM_OUT/BPF_MONI
(SEE PAGE 4-35) C809
(2/10)
C803
XX XX
C804
XX
2.4 C843 R819
XCS_AU
RF_SWP 69
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
SP+ GND(BPF) XCS_AU
D SP_GND PB_RF_IN
R0.1/P0
0.01u 820 (6/10)
2.5 R2.3/P2.1 C844
C801 SP- MUTE_TC 68p
22u 4.8 C840 0.001u
6.3V VCCH GND(IIL)
2.4 0.1 XVC_SCK CL804
C808
22u
6.3V
VREFH FSC
1.4 VC_SO CL803
XVC_SCK 81
GND SWP VC_SO
0 2.8 XCS_AU (6/10)
LINE MUTE CS_IN
C805 10u 16V 2.4 2.5 XVC_SCK
AUDIO_L_I/O
C806 2.9
LINE OUT IC801 CK_IN
R0.7/P0.4 VC_SO
0.01u VCC(MIC AMP) AUDIO/VIDEO PROCESS SI_IN
E R803 C802 R806 1.4
MIC IN
IC801
VCCHDR
4.8
XX 10u 16V 2200
R2.3/P0
MIC REG
AN12985A-VB
YSAG
R0.3/P0
CL805 XCS_IO
70
1.2 0.3
(6/10)
79 C810 1u 1.3
VREG
IREF
YOUT
GNDDR
(10/10) R807 47k ± 0.5% 2
GND(MIC AMP) VOUT
C807 10u 16V 1.4 2
VREF VSAG REC_AFM
1.4 0.4
MIC_PRI_AMP_OUT COUT PB_RF
38
MIC_AMP_OUT
NR_MONITOR
F 1.5M_DEV
MIC_FL_OUT
PB_DC_CUT
EE_OFFSET
MIC_FL_IN
C841 (4/10)
FADE CTL
DEV_ADJ
GND(FM)
A_FADE
BPF_ADJ
VCCHYC
10u
LINE_IN
GNDYC
INT_MIC
AGCTC
16V
AU_BPF
YIN
CIN
C842
0.01u
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
R1.4/P0
R1.4/P0
0
R1.4/P0.1
1.4
1.4
1.4 0 0 2 2
2.1
4.8
L801
17 C_OUT
CL801
C812
10uH
C838
C816 XX C849 22u 6.3V
0.01u 6.3V
C814
C818
C824
0.47u
C820
C835
C850
C827
6.3V
C829
3.3u
50V
0.1u
XX
XX
1u
0.1u 1u
H 16 IC_301_Y_OUT
(2/10) IC_301_C_OUT
05 ed IC801 wa REC/PB (S JACK IN) ef IC801 ql REC/PB (AV JACK IN) eg IC801 qj REC/PB (S JACK IN)
H H H
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
DRUM_VS
MT_5V
BT901 F001
B DC IN
(1.4A/32V)
CAP_VS
VTR_UNREG 52
R064 R067 REG_GND
(5/10)
10 1200 REG_GND (MT-GND)
C052 C051 8
CN053 6P XX XX 4 F003 D_2.8V
(1.4A/32V)
BATT_GND 1
8 3 1
8.3
EP_13.5V
BATT/XEXT 2 IN1
2 8.3 REG_GND
R051 R053
ACV_GND 3 100k 7 8 7.6 1.5
1k D_1.5V
F004
ACV_UNREG 4 6 8.1
Q053 (1.4A/32V)
2 1
L055
22uH
L058
4.7uH
C094
10u A_2.8V 15
C BATT_SIG 5
8 5
8.3 2SB798-T1
-DLDK 6.9 Q056
XN0NE9200LS0
6.3V
D_2.8V (2/10)
S BATT_UNREG 6
Q052 3 SWITCHING A_4.6V
UPA1858GR-9JG R068 8.3 4 5 L059 C095
-E2-A 6800 F002 4.7uH 4.7u
SWITCH (1.4A/32V) C077 C085
XX 4.7u L060 4.7uH
BATTERY
TERMINAL IN2 L061 4.7uH
D_2.8V
3 4
0
C055
0.022u
R062
0.1 15.7 L062 4.7uH
D_1.5V
66
D051 3 L052 FB051 0uH
D052 1M 22uH (6/10)
DF3A6.8FV 0 REG_GND
D (TH3SONY)
MA4ZD03001S0
Q054
2 1
Q057
4.7u
2.5 C096 C100
C098 C102
C073 10u
2 1 Q051 UNR32A300LS0 XN0NE9200LS0 33u
C074 XX
3 4.7u 1u 4.7u
2SC584600LS0 SWITCHING 4V
5
C071
SWITCH Q053,054 8.3 4
CHARGE CONTROL L063 22uH
C078 C086
4.7u 4.7u L064 4.7uH
L066 47uH
IN7
2.9
46 DRUM_ERROR
R076 L056
RP_4.6V
E (5/10)
CAP_ERROR
0 2 1
Q058
22uH C097
22u
6.3V
C099
2.2u
C101
XX
6.3V
C103
4.7u
C104
22u
6.3V
AU_2.8V
A_4.6V
36
5.2
R070 XN0NE9200LS0 (4/10)
R077 3
84 BL_CONT
33k 120k
8.3 4 5
SWITCHING
C087
8.3 5
R097
REG_GND
5
R065 4700
8.3 4 5
R071 10k
2
R072 1k
R073 1k
R075 1k
1.3
C079 C088 Q069 A_4.6V
1 4
R069
0.015u
0.033u
0.022u
CAP_VS (3/10)
2200p
C064
REG_GND
C067
C070
C072
C062
1 REG_GND (MT-GND)
C057 L053
6800p
22uH
G 7.2
2 1
Q060
D_2.8V
1.4
1.4
1.2
0.8
1.2
0.3
0.3
0.6
0.6
0.6
0.6
0.8
1.2
2.5
XN0NE9200LS0 MT_5V
1
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 8.3 4 5
SWITCHING
R085 Q066,073
R096
100k
EVER_3.0V 88
Q066
100k ± 0.5%
FB2
-INE2
+INE2
-INE3
FB3
FB4
-INE4
+INE5
-INE5
FB5
+INE6
-INE6
FB6
FB7
-INE7
DTC6
HI_EVER_SCK
3
CLK ej IC051 ya REC/PB SENSE
0
Q055
4 2 4.8
R114
0 R4.3/P5.4 R103 CAM_DD_ON
89
C053 0.1u 3 8.3 MCH3335-S 3 Q062 39k
RST VCONT -TL-E CPH5819-TL-E C111
R063 ± 0.5% (6/10)
R052 30k 47k Q064
0.8 SWITCH 8.3 R3.4/P2.4 SWITCHING R2.8/P0
RT 8.4 Vp-p LANC_SIG XX 2SC584600LS0
C054 0.1u 0 SWITCH R104
CSCP DATA_IN C075
4.7u C083 7500
3 1u R2.2/P0 ± 0.5%
SEL NTSC: 512 kHz WAKE_UP
C091 R093 C107 C106 EP_2.8V
C076
PAL: 485 kHz 4.7u C082 D055 0.1u 22k 4.7u 4.7u
MA4ZD03001S0 EP_4.6V
DATA_OUT
J 1u
4 1 0 13.6
REG_3V
EP_13.5V
OUTC3
RESET
XCTL2
R061
VOUT
CDET
VBAT
VREF
CTL1
3 2 R105
GND
VRO
BL_REG
VR
100k
CS
CS
1u R089 Q071 XX
100k 2SA207800LS0 ± 0.5%
74 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
15.2
6 3 C108
REG_GND (BL-GND)
REG_GND
(7/10)
2.2u
90
2.4
1.2
7.7
2.5
3.1
3.3
3
3
7.7
2.9
4.8 4.9
2 5 R106
Q072
XRESET Q071,072 UP04501008S0 47k (10/10)
1 4 ± 0.5%
13.5V REG
VTR_DD_ON
BATT_IN 4.3
K R094
22k
R107
8200
-15.4 -15.4
PANEL_-15.3V
EVER_3.0V R109
R090 Q068 0
100k 2SC584600LS0 ± 5%
-14.8
3 6 R110
220k
SIGNAL PATH
REG_GND D054 0 ± 0.5%
MAS3132E0LS0
VOUT Q074
5 2 C109 REC REC/PB PB
86 (10/10)
Q068,074
15.3V REG
UP04401008S0 4 1
2.2u
L R083
470
LI_3V
0.5
R095
R111
68k Drum servo(speed and phase)
D053
100k ± 0.5%
87
0.047u
0.047u
0.1u
0.1u
-THP3
C061 XX
C066 1u
C069 1u
59
C058
C059
C065
C068
C063
DCOUT_ON (6/10)
Q075
UNR32A300LS0
SWITCH
05
The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont
line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que
Replace only with part number specified. par une piéce portant le numéro spécifié.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
PANEL_G 6
PANEL_R
XCS_LCD
60 (6/10)
KEY_AD3
KEY_AD3
3.3V REG LI_3V
86 (9/10)
PANEL_R 7 (7/10) XBATT_INFO_SW IC001
KEY_AD5 XBATT_INFO_SW
KEY_AD5 TK11133CSCL-G
PANEL_XVD 8 DIAL_A 4 5
PD-204 PANEL_SYNC KEY_AD7 DIAL_A
CN6001 C-SYNC/XHD 9 KEY_AD7 DIAL_B C003 3.3 4.8
XCS_LCD XCHARGE_LED DIAL_B 4.7u
THROUGH THE XCS_LCD_DA 10 XCHARGE_LED
C
PD-124 HARNESS
(PAGE 4-29)
XVC_SCK 11
R001 470 XVC_SCK
VC_SO
XCAM_LED
XVTR_LED
XCAM_LED 72 85 (7/10) XRESET
XRESET CN005 22P
1 REG_GND
VC_SO 12 XVTR_LED (7/10)
VC_SI XPOWER_SW 2 N.C
VC_SI(HDO) 13 BL_REG XPOWER_SW
LCD_HOLD XMODE_SW V_LIGHT_PWM 3 LI_3V
PANEL_HOLD 14 REG_GND (BL_GND)
XEJECT_SW
XMODE_SW 56 (6/10) V_LIGHT_PWM
4 D_2.8V
REG_GND 15 XEJECT_SW KEY_AD0
5 KEY_AD0
PANEL_-15.3V 16 PANEL_-15.3V
90 ZOOM_VR_AD INT_MIC
INT_MIC XBATT_INFO_SW
6 BATT_INFO
PANEL_2.8V 17 EP_2.8V
(9/10)
ZOOM_VR_AD 57 (6/10) 79 (8/10)
AUDIO_L_I/O
AUDIO_L_I/O
7 CUSTOM_LED_VDD
PANEL_4.6V 18 EP_4.6V
8 N.C
D PANEL_13.5V 19 EP_13.5V XF_TALLY_LED 2.8
UDZSTE-176.8B
KEY_AD5 LCD_HOLD XF_TALLY_LED 9 XCUSTOM_LED_ON
AD5 20 LCD_HOLD 67 (6/10)
73 SIRCS_SIG
SIRCS_SIG 1 2
D008
R018
R003 CUSTOM_LED_ON 0 2 10 REG_GND
150
XX REG_GND SIRCS_PWM
(7/10) SIRCS_PWM 1 11 XMS_LED CONTROLL KEY
Q002
CN006 16P VC_SI AV_JACK_IN UNR32A100LS0 3
BLOCK
12 N.C
XS/S_SW 1
KEY_AD7 VC_SI 94 (6/10) AV_JACK_IN
CUSTOM_LED_ON
LED DRIVE
13 MS_LED_VDD
(CF-5100)
(PAGE 4-35)
CUSTOM_LED_ON KEY_AD1
REG_GND 2
XMODE_SW 53 XS_JACK_IN
XS_JACK_IN 14 KEY_AD1
XMODE_SW 3
XPOWER_SW R021
VC_SO
XVC_SCK
VC_SO 95 (6/10) DCOUT_JACK_IN
DCOUT_JACK_IN
EVF_DD_ON
KEY_AD3
15 D_2.8V
XPOWER_SW 4 150 16 KEY_AD3
E CHARGE_LED_VDD 5
XCHARGE_LED
XVC_SCK (6/10) EVF_DD_ON
VIDEO_I/O KEY_AD2
17 D_2.8V
CONTROLL KEY
N.C 7 PANEL_R 83 S_Y_I/O
S_Y_I/O DIAL_A
19 DIAL_A
BLOCK XCAM_LED 8
XCAM_LED
XVTR_LED
PANEL_G
PANEL_R
PANEL_G
20 (8/10) S_C_I/O
S_C_I/O DIAL_B
D009
20 DIAL_B
(SS-5100) XVTR_LED 9 PANEL_B (2/10) 2 DF3A6.8FV 21 REG_GND
(PAGE 4-34) R014 PANEL_B 1 (TH3SONY)
MODE_LED_VDD 10 LANC_DC 3 22 XRESET
D_2.8V 11
82
87 (9/10) LANC_DC
XRESET
ZOOM_VR_AD
F ZOOM_VR 12
XEJECT_SW
IR_ON
EVER_3.0V
REG_GND 13
N.C 14
68 (6/10) IR_ON VL_16V
88
A_2.8V
N.C 15
XCS_EEP MT_5V (9/10)
XEJECT_SW 16 XCS_EEP CL001
65 (6/10)
SWP_DIR
SWP_DIR D_2.8V
D006 D007
MAZB068H0LS0
1 6
MAZB068H0LS0
1 6 PB_RF
PB_RF
CL002
CL003
MD2 (REG_GND) 64
2 5 2 5
39 (4/10)
REC_2
REC_2 XCS_MC_FLASH (6/10)
G 3 4 3 4
CL004
80 (8/10) REC_AFM
REC_AFM XSYS_RST 92 (7/10)
CL010
CL005
R004 R007 EEP_SI
22
± 0.5%
1k
± 0.5% 91 (5/10) CAP_FG
CAP_FG CL006
EEP_SO
63
CL007
R010 EEP_SCK (6/10)
10k XLANC_PWR_ON
± 0.5% XLANC_PWR_ON
H 15.8
15.8 77 LANC_IN
LANC_IN CL008
REC_CRRT1
3 1 R011
1k (7/10) LANC_OUT
LANC_OUT CL009
REC_CRRT0
93 (6/10)
2 5 0 R022
1k CN007 16P
XCS_EEP
15.8 Q001
CN009 30P 16 XCS_EEP
4 6 XN4601-TW
VL+ 1 VIDEO 15 EEP_SI
0 LIGHT
MIC_GND 2 DRIVE 14 EEP_SO
V_LIGHT_PWM XLANC_PWR_ON
MIC_GND 3 13 XLANC_PWR_ON
INT_MIC LANC_IN
INT_MIC 4 12 LANC_IN
I LIA1 5
LANC_OUT
11 LANC_OUT
VREF1 6 10 REG_GND
C279 PB_RF
LIA2 7 XX 9 PB_RF CPC
C278 R273
VREF2 8 22u 10k L271 8 REG_GND (FOR CHECK)
R275 REC_2
10uH
A_2.8V 9 XX 7 REC_RF
A_2.8V 10 C282 6 REG_GND
XF_TALLY_LED 0.047u R274 SWP_DIR
XF_TALLY_LED 11 10V 1M 5 SWP_DIR
CAP_FG
D_2.8V 12 4 CAP_FG
SIRCS_SIG PITCH_AD REC_AFM
J SI-039
CN755
XSIRCS_SIG 13 3 BPF_MONI
MT_5V 14 2 PB_RF
THROUGH THE D001 C280
0.7
0.9
1.3
1.3
1.3
1.3
1.3
1.3
R002 4.7u
FP-795 FLEXIBLE MT_5V 15 2200 2 MAS3132E0LS0 IR_ON 1 EEP_SCK
3 RB271
(PAGE 4-32) SIRCS_PWM/IR_DRV_EN 16 1 SIRCS_PWM 10 9 8 7 6 5 4 3 2 1
22k
SIGNAL PATH SIGNAL PATH
GND
AM1
HO1
OUT1
PASS
LO1
AV_JACK_IN 17
HI1
LIB1
LIA1
IC271
Vref1
AV_JACK_IN
AUDIO_L_I/O 18
AUDIO_L_I/O STEADYSHOT
54 VIDEO SIGNAL
AUDIO VIDEO/AUDIO/
REG_GND 19
SERVO
Vref2
LIA2
OUT2
CRST
SIGNAL SIGNAL
LO2
HI2
HO2
AM2
VCC
1.3
1.3
1.3
0
2.8
C281
REG_GND 23 0.1u
XS_JACK_IN 6.3V
XS_JACK_IN 24 PB
REG_GND 25 VST_C_RESET
S_C_I/O
YAW_AD
S_C_I/O 26
R271
SIGNAL PATH
C283 C276
REG_GND 27 0.047u 1M
LACN_DC 22u
10V
RFU_DC 28 R272 REC REC/PB PB
10k
L RFU_DC 29
DCOUT_JACK_IN
DCOUT_JACK_IN 30 Capstan speed servo
TRV328/TRV428/TRV428E
05
Ref.signal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
PANEL_4.6V 18
PANEL_2.8V 17
FB6001
TG25
TG24
TG23
TG22
TG19
PANEL_-15.3V 16
L6001
REG_GND 15 47uH
PANEL_HOLD
PANEL_HOLD 14 C6019 C6020
BLDET
XLED
EXTDA
C6002 3.3u
SO 22u 1u
VC-341 VC_SI(HDO) 13 4V 25V
SI
(10/10) VC_SO 12
C CN002
XVC_SCK 11
SCK C6001
0.1u
C6006
0.01u
CL6012
THROUGH THE XCS
<0.4>(1.4)
<0.3>(2.8)
CL6007
<1.4>(0.1)
<2.1>(1.2)
PD-124 HARNESS XCS_LCD_DA 10
<0>(2.8)
CL6016 XHD
(PAGE 4-27) C-SYNC/XHD 9 C6022
13.6
C6028
1.4
1.7
2.6
6.8
XVD 0.1u
PANEL_XVD 8 10u
CL6017 16V CN6004 24P
PANEL_R 7 4 IC6001 rs REC/PB 36 35 34 33 32 31 30 29 28 27 26 25
CL6013
24 VSH/VSH5V
R6030
PANEL_G 6
VSS2
HCNT / SPD
MCLK / CLD
CLR / CTR
OE / PSS2
PWM / PWMOP
BLDET
RESET / EX2
EXTDA
XLED
VCC3
COM OUT
D6009 5600
23 VDD/VSH3V
PANEL_B 5 2.8 Vp-p RB521S-30-TE61
22 VSS/GND
BL_CONT 4 VB
D BL_GND 3 VG
21 VB/VB
V 2.8 20 VG/VG
37
24
BL_REG 2 VDD2 NC / CSD VR
2.8 19 VR/VR
SE_GND 1 3 IC6001 r; REC/PB 1.5 TG25
38
23
BIN COM DA 18 HCNT/SPD
C6003 0.01u 1.7 TG24
4.8 17 MCLK/CLD
470 mVp-p
39
22
GIN VCC2 TG23
C6004 0.01u 1.8 RB6003 16 CLR/CTR
2.4 100 TG22
40
21
RIN VB CL6004 15 OE/PSS2 LCD901
C6005 0.01u 1.7 VB TG20
2.4 14 SRT/PSS1 2.5INCH
H COLOR
41
20
SCANEN / TEST VG CL6005 TG17 LCD
E XVD 2.4
VG
TG16
13 STBYB/RES
UNIT
42
19
XVD / VDIN VR VR 12 VBC/CLS
2.8
XHD IC6001 CL6006 11 VCOM/VCOM
43
18
HD / SYNI/HD GND2 TG19
2.6 LCD DRIVER 10 RESET/EX2
IC6001 TG15
44
17
VCC1 GND1 TYPE S 9 STBYB/PSG
2.8 TG14
CM7104L42-T4:TYPE C
XCS <2.6>(0) TG18 C6029 8 GSRT/MO2
LRS57231:TYPE S
45
16
XCS GRES / EX1 1u TG13
2.8 25V 7 GPCK/MO1
SCK Note1: IC6001 Pin Name A/B
<2.8>(1.4) TG17 TG18
46
15
XSCK STBYB / RES 6 GRES/EX1
A: TYPE C MODEL D6006
F CN6005 6P
SI
2.6
B: TYPE S MODEL <1.7>(2) TG16 1SS355TE-17
TG12
5 N.C./SPS
47
14
PANEL_REV 1 SI N.C / CLS
R6042 XX 0.2 4 VDD/VGLAC
CONTROL PANEL_REV 2 SO 2.8
48
13
SO VDD1 3 VGL/VGL
KEY Q6005
GPCK / MODE1
GSRT / MODE2
N.C. 3 2.6 R6031
BLOCK
STBYB / PSG
0 HN1B04FE-Y/GR(TPLR3) 2 VSS/GND
POCB/LOWI
SRT / PSS1
W/H / HWB
N.C. 4 R6032
(PR-5100)
CP / SPS
120k TYPE C 1 VGH/VGH
OPOUT
(PAGE 4-34) SE_GND 5
Filter2
13.5 TYPE C
VSS1
OPIN
Filter
TYPE C Note2: CN6004 Pin Name A/B
SE_GND 6 12.9
5 IC6001 rd REC/PB C6015
1u
6 4 R6020
0
A: TYPE C MODEL
B: TYPE S MODEL
1 2 3 4 5 6 7 8 9 10 11 12 16V 4.7 12.9
5
G 2.8 Vp-p 0
2
<1.4>(2.8)
<0.1>(2.8)
<0>(2.8)
<0.1>(2.2)
2.8
1.4
1.4
2.6
1.3
1.2
1 3 CL6014
4.1 13.5
9 IC6001 ql REC/PB
3.2 Vp-p RB6001 Q6004,6005
H (TYPE C) 10k SWITCH
3.5 Vp-p
(TYPE S)
TG12
TG13
TG14
TG20
TG15
PANEL_HOLD
Q6004
2H HN1B04FE-Y/GR(TPLR3)
CL6015
R6036 R6008
3.4 -15.6
H XX XX
4 6
C6030 R6012 10k 5 -15
XX C6010 1/16W ± 0.5% 2
560p 2.8
3 1
C6009 R6009 R6013 100k -15 -15.6
R6035
Q6007
0.1u 68k 1/16W ± 0.5% C6016
XX 0.01u
XX
D6007 XX
R6029 XX TYPE C RB6002
R6026 R6019
I TYPE S 0 C6024
1u
0
TYPE C
1M
TYPE S
L6004 22uH 4.7 4.7 16V
C6026 C6027
22u R6040
6.3V 0.1u Q6009
47k
2SA1832FV
(TH3SONY)
EXTDA R6041 Q6008,6009 4 R6039
1k B+ SWITCH 3900
0.1
2.6
1
D6008
XX
2 6
3
CN6003 10P
4 10 10 BL_HIGH
K 5.4 5.4
C6011
0.015u
C6013
12pF
9 N.C
2 1 6 4 8 N.C
3 5 1 T6001 7 N.C
INVERTER
3 ND901
-0.7 -0.7 TRANSFORMER 6 N.C BACKLIGHT
4 2 5 Q6003
C6007 Q6002 5 N.C
CPH5504-4TE-E XX
D6002 4.7u
XX INVERTER DRIVE 4 N.C
10V
R6011
XX 3 BL_LOW
2 LED
SIGNAL PATH
L R6001 Q6001
XX D6004
D6005
XX
1 LED_GND
XX
XLED MA111-(K8).S0 TYPE C MODEL VIDEO SIGNAL
R6002 1SS355TE-17 TYPE S MODEL
BLDET
XX
R6010 C6012 R6014
CHROMA
D6003 22k 0.1u 470
XX
LND605
REC
A
PB
M
05
The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont
line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que
Replace only with part number specified. par une piéce portant le numéro spécifié.
1 2 3 4 5 6 7 8 9 10 11
A
SIGNAL PATH
FP-792 FLEXIBLE BOARD
VIDEO SIGNAL
AUDIO VIDEO LIGHT
CHROMA Y Y/CHROMA SIGNAL D002
NSPW500BS-TL2
REG_GND 1
REC VL+
D001 D003 D001-003
NSPW500BS-TL2 NSPW500BS-TL2 (VIDEO LIGHT)
PB
B LAND1
STATIC_GND REG_GND 3
STATIC_GND
LAND2
C
SI-039 BOARD C754
R760 XX
LND759
STEADYSHOT,JACK XX
R759
XX REG_GND 1
LND756
XX MARK:NO MOUNT R761
0 VL +
TRV328
NO MARK:REC/PB MODE /TRV428
2.8 1.3 1.3
LND760
/TRV428E 3 4 1 2
3
REG_GND
GND
OUT
GND Vref
Note: D753, D754, IC751, J751, J752 and J753 are SE751
SE752
YAW LND754
not included in SI-039 complete board.
OUT
PITCH
D
Vref
SENSOR SENSOR MIC_GND
V
C751 MIC901
XX 1 2 3 4 LND755 MICROPHONE
1.3 1.3 2.8 INT_MIC
C753
R751 XX
XX C759 CN755 30P
4V
4.7u
C755 30 VL+
2.8 XX C757 R762
VCC
3
4V XX 29 MIC_GND
XX
GND
2
28 MIC_GND
R OUT C758 VDR757
1
27 INT_MIC
4.7u
E C Y
2.8
R754
XX
26 LIA1
4 3
XX FB751 25 VREF1
C
J751 S1 6
S
Y
S
5 S2
IC751 24
23
LIA2
VREF2
S VIDEO S S REMOTE COMMANDER
OUT S3 8 G G 7 RECEIVER D759 22 A_2.8V
1 S4 TLRMV1021(T15SOY,F)
IC751 R763
2 RPM7240-V4 (TALLY) 21 A_2.8V
CGND YGND 1k
TRV228/TRV228E 20 XF_TALLY_LED
/TRV428/TRV428E
F Q751
19 D_2.8V
2SD2114KT146 R752 56
18 XSIRCS_SIG VC-341
LED DRIVE R755
XX 17 MT_5V (10/10)
3 1 3 CN009
16 MT_5V
THROUGH THE
R753
D753 D754 56 15 SIRCS_PWM/IR_DRV_EN FP-795 FLEXIBLE
2 DAC3825 DAC3825 C752
0.2 (IR EMITTER) (IR EMITTER) XX 14 AV_JACK_IN (PAGE 4-27)
13 AUDIO_L_I/O
12 REG_GND
11 VIDEO_I/O
G J752
1
2
3
GND
L
V 10 REG_GND
A/V 4 BR
5 SW 9 S_Y_I/O
OUT
7 R 8 REG_GND
6 NC
D755 D752 D751
RSE6.8XN-TR 7 XS_JACK_IN
RSE6.8XN-TR RSE6.8XN-TR
1 6 1 6 1 6 6 REG_GND
2 5 2 5 2 5 5 S_C_I/O
3 4 3 4 3 4 4 REG_GND
LND751
3 RFU_DC
STATIC_GND
2 RFU_DC
LND752
1 DCOUT_JACK_IN
STATIC_GND
H
3 R
J753 4 BR FB752 XX
RFU DC 2 L
OUT
1 GND
05
1 2 3 4 5
FP-302 FP-802 FLEXIBLE FP-300
FLEXIBLE FLEXIBLE
CONTROL KEY BLOCK
A
Q002
TAPE END
Q001
TAPE TOP
(SS-5100)
XX MARK:NO MOUNT
• CONTROL KEY BLOCK (SS-5100) is replaced as block,
so that PRINTED WIRING BOARD is omitted. VC-341
1 TAPE_TOP (C) (10/10)
2 TAPE_END (C) CN006
(PAGE 4-27)
D001 3 TAPE_LED (K)
TAPE LED
4 TAPE_LED (A)
B
CHARGE_LED_VDD
REG_GND
4 XPOWER_SW
5
MODE_LED_VDD
6 XCHARGE_LED
3 XMODE_SW
16 XEJECT_SW
8 XCAM_LED
9 XVTR_LED
12 ZOOM_VR
6 S REEL (-)
2 REG_GND
13 REG_GND
FP-301
1 XS/S_SW
STATIC GND
LND001
VC-341 BOARD
11 D_2.8V
7 S REEL (+)
(5/10)
7 N.C
14 N.C
15 N.C
H002 3
FLEXIBLE 2
S REEL
8
9
SENSOR_VCC
T_REEL (+)
CN404
(PAGE 4-17)
10
5
1 SENSOR 4
10 T_REEL (-)
11 HALL_COM
ME/MP
12 ME/MP
REC PROOF
13 REC_PROOF 2 4
2 H001 3 Hi8 MP S001
T REEL
1 SENSOR 4
14
15
Hi8_MP
C_LOCK_SW
C (START/STOP)
S003
S001 XX
D003 XX
D002
D001
D004
1 3
R001 1k
S002
C.C. LOCK
POWER/MODE_SW
POWER
(CHG) S004
CHG D004
CAMERA D002
D001
OFF REG_GND
D ON
XPOWER_SW
PLAY/EDIT
S901
MODE SWITCH XMODE_SW S002
1 DEW MODE
(EJECT)
2 M-SW (A)
FP-299 3
4
M-SW (B)
M-SW (C)
FLEXIBLE MR 2
1 5
6
FG1
FG VCC
RV001
20k
SENSOR 3 7 FG2 E
4 8 REG_GND
W (ZOOM) T
9 CAP_U
DEW SENSOR
10 CAP_U
11 CAP_W VC-341 BOARD 05
(5/10)
12 CAP_W
CN403
13 CAP_V (PAGE 4-17)
M902
FP-228 CAPSTAN MOTOR 14 CAP_V
15 VH+ 1 2 3 4
FLEXIBLE 3 2
16
17
HU1
HU2
HE
4
3
1
2
18
19
20
HV1
HV2
HW1
CONTROL KEY BLOCK
A
4 HE
1
21
22
HW2
VH-
(PR-5100)
XX MARK:NO MOUNT
3 2
HE • CONTROL KEY BLOCK (PR-5100) is replaced as block,
4 1 so that PRINTED WIRING BOARD is omitted.
REC REC/PB PB
1 PANEL_REV
3 N.C
Capstan servo(speed and phase)
PD-204
4 N.C CN6005
(PAGE 4-29)
5 SE_GND
6 SE_GND
05
4-33
FP-228, FP-299, FP-300, FP-301, FP-302, FP-802, SS-5100, PR-5100 4-34
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
4-2. SCHEMATIC DIAGRAMS
1 2 3 4 5 6 7 8 9 10 11 12
B1 A1 B1 A1 B1 A1 B1 A1 B1 A1 B1 A1
2 1 2 1 2 1 2 1 2 1 2 1
B B2 4 3 A2 B2 4 3 A2 B2 4 3 A2 B2 4 3 A2 B2 4 3 A2 4 3
B2 A2
D002
EASY
BT001
LITHIUM
BATTERY
S004
BATT_INFO
CUSTOM_LED_VDD B1 A1 VOLUME
D 2 1 S001 S005 S009 S013
S7
A1
COM 2
SW1A 3
SW2 4
SW1B 5
B6
N.C DSPL/BATT R015 - + R021
TIME R007 MENU R011 END SEARCH R019
3 A2 INFO 1200 1500 2200 S017 3900 S021 8200
XCUSTOM_LED_ON B2 4
REG_GND
VC-341
B1 A1 B1 A1 B1 A1 B1 A1 B1 A1
(10/10) XMS_LED
D001 2 1 2 1 2 1 2 1 2 1
CN005 XX
(PAGE 4-28) N.C
D_2.8V
R003 10k
E KEY_AD3
D_2.8V
S006 S010 S014 S018
KEY_AD2 R008 R012 R016
R004 DATE 1200 EXPOSURE 1500 TITLE 2200 EASY DUB
DIAL_A 10k
DIAL_B
A1 B1 A1 A1
REG_GND B1
2 1 2 1
B1 2 1 A1 B1
2 1
22 XRESET
F B1
2 1
A1
B2 4 3 A2 B2 4 3 A2 B2 4 3 A2 B2 4 3 A2
S002
4 3 RESET
B2 A2
G LND025
CH GND
05
Link
PD-204 BOARD
2 1 1 2 3 3 2 1
Pattern
Board Name Parts Location
Total Number of Layers Layers Not Indicated
CD-465 – 4 layers 2 to 3 layers
VC-341 4-53 4 layers 2 to 3 layers
PD-204 4-54 2 layers –
SI-039 4-54 2 layers –
FP-792 Flexible – 1 layer –
FP-228 Flexible – 1 layer –
FP-299 Flexible – 1 layer –
FP-300 Flexible – 1 layer –
FP-301 Flexible – 1 layer –
FP-302 Flexible – 1 layer –
FP-802 Flexible – 1 layer –
4-39
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
CD-465
Note for Printed Wiring Board (See page 4-39).
CD-465 BOARD
14
13
C953
CN951
L951
R952
Q951
1
C952
E
C
C951
R953
B
1 5
1 7
2 3 4 C954
IC951 C955
7 8 9
LND951
14 8
6 1-860-933- 11 (21)
05
VC-341 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION
Note for Printed Wiring Board (See page 4-39).
CN403
CN481
22 1
11 1
A R401
CN402
FB482 FB481
R402 10 1
R493
C493
R484 C489 R495
C488 R487
R494
C499
C494
C501
36 25
C496
37 24 C502
C504
C497
19
IC481
22 21 20 13
ET482
C505
48
1 12
C508
C507
C514 C509
C515 RB482
ET481
1
2
CL801
C601 R606
C604
C602
C620
R601
R602
R605
CN151
C605
C606
C603
X601
54 1
13
55 216
14
29
C CN401
RB601 2 1
R636
C401
CL614
RB603
RB602
R333
D203
C402
C403
Q202
C331
C609
C610
CL602
FB601
3 2 1
4 IC601
1
5
C003
24 2 CL618
RB605
IC001
CN004
CN201
RB606
23 1 CL604
C002
7
8
R218 CL606
RB203
L201
CL605
RB612
C715
R717
R718
C624
R716
1
CL617 CL611
C611
Q701
C210
K2
40 21 CL612 108 30 163
C708
41 20
C807
C815
C805
R021
109 162
32
16
R715 CL609
R005
C622
R014
R006
C614
RB608
CL613 CL616 C625 C623
R713
C714
C615
D007
CN009
E R619
C616
CN006
31 IC701
RB610
C617 CL301
R709
R616 C612
C820
C817
C841
R714
C712
C618 CL805
X702
C339
R708
RB706
R707
D006
1
R711 60 1
RB705
R710 61 80 R051
KAK
R706
R705
30
C802
C825
C849
C713
L058 + C094 A D055 C082 C084 D051
C709
F001
D009
C707
RB703
RB701
C071
RB704
KA K
CL802
C704
C701
C711
C705
C051 C052
R704
C710
C702
C703
L062
C098
R712
C102
1
F L056 L055 L051
C845
C074
C801
C808
L061
FB051
C848
C100
1 21
+ C101 A
+
F004
CN005
CN053
C103
R002
2 22
L065 F003 4 1
C073
R067
RB801
R064
R018
C
Q002 B E
L063
Q052
+
Q001 CL803 CL804
A C097 +
6
5 8
D008
C
CN008 F002
R007 Q053
R011
AK A 1 C
CN002 20
G
R053
A C104 + B E
C055
1 2 B E
D001 L066
Q051
D052
R001 C
B E
L059
R068
C095
Q054 1-860-932- 11 (21)
05
1 2 3 4 5 6 7 8 9
VC-341 (SIDE A) 4-43 4-44
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION
Note for Printed Wiring Board (See page 4-39).
C422
C421
C419
C418
C416
C414
R428
C500
L481
C412
Q482
C481
C411
R483
C423
RB483
C446
C
C426 B E
C444
R426
C407 CN404
A
L484
R482
RB401
L483
B E
R481
C485
+ C482 B
R413
C
C428
R405
15 1
C405
40
21
C445 C427 C409
FB401
Q481 R491 R490
41
20
R492
C503 C
C498
28 R404 C406 B E
C490
C492
R414 C486
C408
R427 C430 R403 R409
C491
L482
C404 Q401
27
C487
C483
C440
R488
R489
C484
C495
RB481
C443
R423
R418
C166 R164
C410
IC401
R425
26 FB252 C252 Q483
Q485
Q484
1 X151 2
R431
25
R158
R160
28
R416
B E
R406
D151
23 C155
B E
R430
C
C429
C
R156
C511
C510
24
R159
R161
C442
C441 C154 C161
FB152
C513 R157
C437
C433
C164 C163 R163
R424
60
IC251
4
61
80
C167 C180
C431
C435
B
13
24
C434 12 1
25
13
12
R153 48
C168
3 2 1
C158
FB251
R408
C169
IC152
R407
5
R412
R411
R410
R151
C424
C152
IC151
C425
C439
C436
C432
C251
C413
C170
14
15
C171
FB151
1
R429 24 37
36
C151
C153
C420
C417
C415
48
25 36
6
37
C172
C159
C173
Q302
R155
RB302
C162
C179
A C177 +
C157
L151
C165
R309
C160
R321 C156
R307
R306
1
8
C320
C607
R328
C304 R322
C310
R152
C309 C176
C323
4
5
R325
C
C321
R308
R315
C319
L304
C305
R302
R162
L301
C311
R316
R329 C317 R326 C315 R323 C313 R318 R317
L305
D202
R339
B E
C307
R303
C
C322
C324
C325
R331 R319
Q306
C302
R205
R207
C206
R203
C203
C306 C318 R327 C316 R324 C314 R320 C312 R313 Q201
R330
C216
R217
C
R204
Q304 L303 B E R210
1
R212
R208
R211
R311 C329
54 1
L306
R310
RB301
55
24
216
15 14 13 12 11 10 9 8 C301
C209
1 1
7
8
C204 R206 R209
CL010
L302
C207
R338
IC202
CL009 C303 R216 C214
R314
A
CL008 C308
CN007
IC201
D302
C
R332
C212
CL006 C333 C213
R312
K
CL005 C328
RB201
CL004 R340
A
RB611
RB202
C330
R334
R213 14
CL003 C205
1
R022 C619 C327 16 R215
L308
CL002
A
C332
C211
D301
CL001 E CB
13
12 12
L202
16
C217
C219
1
K
8
C326
17 Q203
IC602
C335
D
A
C334
4
R271 R272
R335 R336
18 C283
R086
IC301
C336
C105
C
B E Q065 20 11
C341
R098 R097 CL302
L271
E
C338
R301 C281
13
12
Q063
Q069
IC271
C
RB271
C340
C280
B
C337
IC302
R092 1 10
C093
R099
R274 R273
R341
C282
R077
C072
R078
C067
R073
R069
C064
R275
C279
C850
24
1
R072
R075
R074
R076
C070
R071
C062
C838
R815
C837
108 R803
R065
163
C816
C827
C824
C835
C821
C060
109 162
C818
C832
R070
L802
C057
Q075
C829 R812
B E
R818
C
C814
R058 R057 R066
R810
C847
16 1
R054 C056 16 1
17 34 64 C812
35 C810
R056
R055
17 36 64 R807
R806
C842
C076
R802
R059
R060
33 C806
37 IC801
C811
R061
Q058
IC051 C083
+ A
Q056
C077
C096
C053
F
C081
C087 C840
R052
C809
C843
Q062
C054 L060 32 49
33 48
R819
C107
C065 32 C085 C844
49 Q064
33 48 Q073
D053
C
R104
R063
R093
C091
R102
C804
C803
B E
L801
R103
C819
C836
C834
C830 C813
C822
R091
Q057
R088
R083 C828
C069
R082
C080
C061
C075
C078
C079
Q061 R817
Q060
R814
C833
C831
C090
B E
C063
C C106
Q070
C068
B E
C089
C059
Q059
C839
C823
C826
R096
C088
R100
R811
C058 Q068
R085
R087R094 Q072
R106
C086 E B
Q055
G
D054
C
AKA
G
R110
R108
S
C111 R089
Q074
C109
C110
C108 R090
Q071
R105
E B
R114
R116
05
9 8 7 6 5 4 3 2 1
PD-204
Note for Printed Wiring Board (See page 4-39).
PD-204 BOARD
L6002
Q6007
C6007
R6035
EC B
A
1
+ C6019 A C6011
C6003 C6030
R6036
LND605
D6007
L6003
C6005
C6004
4 Q6002 Note: Q6002 and Q6003 have the same mount location.
L6001
2 1
C6001
CL6017CL6016
1 C6020
3 4 5 When replacing Q6002 or Q6003, please refer to
5 Q6003 schematic diagram and electrical parts list.
6 5 4
R6005
R6042 CL6012 1 2 3
FB6002
37
48
CN6001
36
3
1
5 4 3 2 1
2
R6008
IC6001
R6009 C6009
C6028
R6012 C6010
8 6
7
B C6006
R6013
9
25
12
24
13
C6002 T6001
C6029
R6030
CL6007
20
FB6001
D6009
R6032 RB6003
R6031
Q6005
CL6004CL6005 CL6006
D6006
R6041 6 10
D6008 C6027
E B
C6015
C
R6020 RB6001
Q6008
RB6002
Q6009
1
C6013
R6029
CN6005
BC E
C6032
CL6015
R6019
Q6004 R6039
C6022
R6001
1 24 CL6013
D6004 D6002 1 10
Q6001
EC B CN6003
CN6004 R6002
R6011
R6010
C6012
R6014
D D6003
D6005
1-860-938- 11
05
1 2 3 4 5
PD-204 4-47 4-48
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION
FP-792
1-860-
929-
1-860-929- 11
D003
1 3
(VIDEO LIGHT)
A J752 A
A/V OUT
LND759 LND760
2
1
E
Q751
LND756
C
R752
R755
2 4
RFU DC
R751
C751
A
B B
3
4
OUT
R760
J753
SE752
C753
R763
(PITCH) D754
(YAW)
SE751
30
1 3 2
C758
29
D759
3
(TALLY)
1
2
R761 A
IC751
A
C755
K
FB751
R754
1
C759
D751
CN755
C C
D755
FB752
2
D752
3 4
VDR757 5 6
J751
1 2
7 8
LND752
MIC901 S VIDEO
LND755
LND754
D MICROPHONE OUT D
1-860-940- 11 1-860-940- 11
05
1 2 3 4 05
4 3 2 1
Q001
TAPE TOP
1-680-436- SENSOR
1 15
11
1 15
o'
H001
MR SENSOR
T REEL
1
4 SENSOR
DEW SENSOR
1-680-437-
21
1-677-049-
FP-228 11
FLEXIBLE
FP-301 FLEXIBLE
1-680-434-
S901
MODE (CONDUCTOR SIDE)
SWITCH
C
B 11
A
COM
H002
S REEL
FP-302 FLEXIBLE
1 SENSOR (CONDUCTOR SIDE)
o' 1-689-290- 11
22
Q002
1-680-438-
TAPE END
SENSOR
11
4-51
FP-228, FP-299, FP-300, FP-301, FP-302, FP-802 4-52
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
4-3. PRINTED WIRING BOARDS
4-53 VC-341
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
4-3. PRINTED WIRING BOARDS
no mark : side A
* mark : side B
PD-204 BOARD SI-039 BOARD
* R481 A-4 C6001 A-2 C758 B-4
* R482 A-5 C6002 B-2 C759 C-3
* R483 A-5 C6003 A-3
R484 A-5 C6004 A-2 * CN755 C-4
R487 A-5 C6005 A-2
* R488 A-5 C6006 B-3 D751 C-2
* R489 A-5 C6007 A-4 D752 C-2
* R490 A-4 C6009 B-2 * D753 B-2
* R491 A-4 C6010 B-2 * D754 B-2
* R492 A-5 C6011 A-5 D755 C-3
R493 A-5 C6012 D-3 D759 C-2
R494 A-4 C6013 C-4
R495 B-5 C6015 C-2 * FB751 C-3
R601 C-7 C6016 C-2
R602 C-7 C6019 A-3 * IC751 C-2
R616 E-7 C6020 A-3
R619 E-6 C6022 C-2 * J751 D-2
R636 C-8 C6024 C-2 * J752 A-1
R704 F-4 C6026 C-3 * J753 B-1
R707 E-3 C6027 C-3
R708 E-3 C6028 B-3 Q751 A-2
R709 E-3 C6029 B-3
R710 E-3 R752 B-2
R711 E-3 CN6001 B-1 R753 B-2
R712 F-4 CN6003 D-4 R761 B-4
R713 E-3 CN6004 D-1 R763 B-2
R714 E-5 CN6005 C-1
R715 E-3 SE751 B-3
R716 D-4 D6004 D-3 * SE752 B-3
R717 D-4 D6006 B-3
R718 D-4 D6009 B-3
* R806 F-1
* R807 F-1 FB6001 B-2
* R810 E-1
* R811 G-2 IC6001 B-2
* R812 E-1
* R815 E-2 L6001 A-3
* R817 G-2 L6002 A-4
* R818 E-2 L6003 A-4
* R819 F-3 L6004 C-3
NOTE
A B C D
E F G H
I J K L
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number,
the original one. please include the board name.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or
• The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety.
supplied. Replace only with part number specified.
• Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque
the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
• CAPACITORS:
le numéro spécifié.
uF: µF
• COILS
uH: µH About PD-204 board and LCD module, dis-
• RESISTORS criminate LCD type on the machine referring
All resistors are in ohms. to page 1-3, and replace the same type.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CND : Canadian model
EE : East European model
HK : Hong Kong model
JE : Tourist model
NE : North European model
5-1
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
6
EVF block
(See page 5-7.)
2 2
2
5 7
11 2
MD frame block
(See page 5-9.) Battery panel block
(See page 5-8.)
8
2 10
3
2
4
9
Cabinet R block
(See page 5-6.)
2
ns
Ref. No. Part No. Description Ref. No. Part No. Description
1 X-3953-964-1 CABINET (C) (515) ASSY, P 7 3-087-810-01 LID (51), CPC
2 3-080-203-31 SREW (M2), LOCK ACE, P2 8 CAUTION RETAINER (51), EVF FLEXIBLE
3 3-087-813-01 COVER (51), JACK 9 3-079-012-01 SCREW (30), TRIPOD
4 3-087-812-01 SHEET (51), JACK 10 3-087-831-01 LABEL (51) (TRV128/TRV228/TRV228E)
5 3-087-811-01 CABINET (UPPER) (51) 10 3-087-831-11 LABEL (51) (TRV328/TRV428/TRV428E)
CAUTION :
For the part of 8 : RETAINER (51), EVF FLEXIBLE
(3-088-616-01), cut WOVEN (T0.25), FABRIC NON
(3-076-631-01) into the desired length and use it.
5-2
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
J752 D003
ns
58
D753
D754
J753
IC751 SI-
03
9
J751
58
59
57
56
55 ns
53
54 58
ns
52
MIC901
51 (Note) D753, D754, IC751, J751, J752 and J753 are not
included in SI-039 complete board.
Ref. No. Part No. Description Ref. No. Part No. Description
51 3-087-738-01 RETAINER (51), MICROPHONE 60 1-860-929-11 FP-792 FLEXIBLE BOARD
52 3-087-740-01 PLATE (51), MAGNIFICATION D001 6-500-744-01 DIODE NSPW500BS-TL2 (VIDEO LIGHT)
53 X-3953-959-1 PANEL (515) ASSY, FRONT (TRV228/TRV228E) D002 6-500-744-01 DIODE NSPW500BS-TL2 (VIDEO LIGHT)
53 X-3953-960-1 PANEL (520) ASSY, FRONT (TRV328) D003 6-500-744-01 DIODE NSPW500BS-TL2 (VIDEO LIGHT)
53 X-3953-961-1 PANEL (525) ASSY, FRONT (TRV428E) D753 8-719-060-65 DIODE DCC3810 (IR EMITTER) (Note)
53 X-3954-020-1 PANEL (510) ASSY, FRONT (TRV128) D754 8-719-060-65 DIODE DCC3810 (IR EMITTER) (Note)
54 3-087-739-01 PLATE (51), NAME IC751 6-704-975-01 IC RPM7240-V4
55 3-087-743-01 SCREW (51), FILTER (TRV228/TRV228E/TRV428/TRV428E)
56 3-087-742-01 RING (51), FRONT J751 1-778-518-11 CONNECTOR, EXTERNAL (S VIDEO OUT) (Note)
57 3-087-749-01 COVER (51), S TERMINAL J752 1-778-040-11 JACK, SMALL TYPE (A/V OUT) (Note)
J753 1-817-944-11 JACK, SMALL TYPE (RFU DC OUT) (Note)
58 3-080-204-21 SCREW, TAPPING, P2
59 A-7111-950-A SI-039 BOARD, COMPLETE (Note) MIC901 1-542-567-11 MICROPHONE
(TRV128/TRV228/TRV228E)
59 A-7111-951-A SI-039 BOARD, COMPLETE (Note)
(TRV328/TRV428/TRV428E)
5-3
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
104
CD
105
-46
5
103
102
IC951
(Note)
101
Ref. No. Part No. Description Ref. No. Part No. Description
101 8-848-765-01 DEVICE, LENS LSV-820A 105 3-080-204-21 SCREW, TAPPING, P2
102 1-758-865-11 FILTER BLOCK OPTICS IC951 A-7013-219-A CCD BLOCK ASSY (CCD IMAGER)
103 3-053-973-01 RUBBER (W), SEAL (TRV128/TRV228/TRV328/TRV428) (Note)
104 A-7111-944-A CD-465 BOARD, COMPLETE IC951 A-7013-276-A CCD BLOCK ASSY (CCD IMAGER)
(TRV228E/TRV428E) (TRV228E/TRV428E) (Note)
104 A-7111-945-A CD-465 BOARD, COMPLETE
(TRV128/TRV228/TRV328/TRV428)
5-4
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
151
LCD901
ND901
152
153
4
-20
PD
154
155
Ref. No. Part No. Description Ref. No. Part No. Description
151 3-087-780-01 CABINET (M) (51), P LCD901 1-805-137-51 INDICATOR MODULE LIQUID CRYSTAL
152 3-087-781-01 FRAME (51), PANEL (TYPE S) (Note)
153 A-7111-949-A PD-204 BOARD, COMPLETE (TYPE C) (Note) LCD901 1-805-138-21 INDICATOR MODULE LIQUID CRYSTAL
153 A-7111-948-A PD-204 BOARD, COMPLETE (TYPE S) (Note) (TYPE C) (Note)
154 3-080-204-21 SCREW, TAPPING, P2 0 ND901 1-518-951-11 TUBE, FLUORESCENT, COLD CATHODE
5-5
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
202
203
201
%
203 204
205
203
203
206
209
207
208
210
! : Included
BT001 (BATTERY, LITHIUM SECONDARY)
in the control switch block (CF-5100).
Ref. No. Part No. Description Ref. No. Part No. Description
201 1-478-416-11 KEY BLOCK, CONTROL (CF-5100) 206 3-087-825-01 COVER (C) (51), HINGE
202 3-080-206-11 SCREW, TAPPING, P2 207 3-078-889-11 SCREW (M1.7)
203 3-080-205-21 SCREW, TAPPING, P2 208 1-478-418-11 KEY BLOCK, CONTROL (PR-5100)
204 1-962-648-11 HARNESS (PD-124) 209 X-3953-962-1 HINGE (51) ASSY
205 3-087-826-01 COVER (M) (51), HINGE 210 X-3953-963-1 CABINET (R) (515) ASSY
5-6
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
251
253
254
255
252 254
256 ns
LCD902
ns
ns
257
258
Ref. No. Part No. Description Ref. No. Part No. Description
251 X-3953-965-1 CABINET (UPPER) (515) ASSY, EVF 257 3-080-203-31 SCREW (M2), LOCK ACE, P2
252 X-3951-166-1 LENS (M) ASSY, VF 258 1-860-928-11 FP-797 FLEXIBLE BOARD
253 X-3953-966-1 CABINET (LOWER) (515) ASSY, EVF LCD902 1-805-465-61 INDICATOR MODULE LIQUID CRYSTAL
254 3-080-204-21 SCREW, TAPPING, P2 (TRV128/TRV228/TRV328/TRV428)
255 X-3953-967-1 BASE (51) ASSY, SLDE LCD902 1-805-465-81 INDICATOR MODULE LIQUID CRYSTAL
(TRV228E/TRV428E)
256 3-087-788-01 BASE (51), SLIDE
5-7
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
ns
304
BT901
301
303
302
Ref. No. Part No. Description Ref. No. Part No. Description
301 3-087-799-01 SHEET METAL (LOWER) (51), STRAP 304 3-072-305-01 LID (2500), JACK
302 3-078-889-11 SCREW (M1.7) BT901 1-694-772-11 TERMINAL BOARD, BATTERY
303 X-3953-968-1 PANEL (515) ASSY, BATTERY
5-8
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
351
352 ns
367
364
ns
363
353 ns
362
354
365
Mechanism deck block
(See page 5-10 to 5-13.)
ns
355 355
355
356
355 1
355 -34
VC
357
361
359
358 360
Ref. No. Part No. Description Ref. No. Part No. Description
351 1-478-417-11 KEY BLOCK, CONTROL (SS-5100) 360 1-827-980-11 CABLE, FLEXIBLE FLAT (FFC-005)
352 3-080-253-01 SCREW (M1.7), LOCK ACE, P2 361 3-088-391-01 SHEET (51), SHIELD, DD
353 X-3953-958-1 FRAME (51) ASSY, CS 362 X-3953-957-1 CABINET (L) (51) ASSY
354 3-080-204-21 SCREW, TAPPING, P2 363 3-978-765-01 SLIDER, G LOCK
355 3-078-889-11 SCREW (M1.7) 364 3-087-802-01 BELT (51), GRIP
356 3-066-169-01 SHEET (30), MD 365 3-080-203-31 SREW (M2), LOCK ACE, P2
357 3-087-809-01 FRAME (51), MD 366 3-087-832-01 LABEL (L) (51) (TRV128)
358 1-860-926-12 FP-795 FLEXIBLE BOARD 366 3-087-832-11 LABEL (L) (51) (TRV228)
359 A-7112-396-A VC-341 BOARD, COMPLETE (SERVICE) 366 3-087-832-21 LABEL (L) (51) (TRV228E)
(TRV428E) 366 3-087-832-31 LABEL (L) (51) (TRV328)
359 A-7112-394-A VC-341 BOARD, COMPLETE (SERVICE)
(TRV228E) 366 3-087-832-51 LABEL (L) (51) (TRV428)
366 3-087-832-61 LABEL (L) (51) (TRV428E)
359 A-7112-393-A VC-341 BOARD, COMPLETE (SERVICE) 367 3-080-204-11 SCREW, TAPPING, P2
(TRV128/TRV228)
359 A-7112-395-A VC-341 BOARD, COMPLETE (SERVICE)
(TRV328/TRV428)
5-9
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
703
705
704
706 707
708
LS chassis block
M901 assembly
(See page 5-11.)
709
712
711
Ref. No. Part No. Description Ref. No. Part No. Description
701 3-065-932-01 PAN (2 MAIN M1.4X1.6), CAMERA 709 3-947-503-01 SCREW (M1.4)
702 3-065-895-01 LEVER, REEL RELEASE 710 X-3951-299-1 SCREW ASSY, DRUM FITTING
703 3-065-896-01 PLATE, BLIND 711 3-074-309-01 ROLLER A, LS GUIDE
704 X-3951-298-1 CASSETTE COMPARTMENT ASSY 712 7-624-101-04 STOP RING 1.2 (E TYPE)
705 X-3951-302-1 DAMPER ASSY M901 A-7048-988-A DRUM (DGH-0F3B-R) (SERVICE) (MDX-M2100)
(TRV128/TRV228/TRV328/TRV428)
706 X-3951-297-1 GEAR ASSY, R DRIVE
707 3-065-840-01 CUT (0.98X3X0.13), LUMILER (W) M901 A-7048-990-A DRUM (DGH-0F4B-R) (SERVICE) (MDX-M2101)
708 3-065-935-01 HLC CUT 1.8X4X0.5 (TRV228E/TRV428E)
5-10
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
755 772
781
775 778 780
752
Q001 S002 776
H001
779
774
FP-802
ns H002
777 773
Q002
FP-301
ns D001
FP-300 FP-302
ns ns
ns
754
753
752
783
751
Ref. No. Part No. Description Ref. No. Part No. Description
751 3-065-822-02 RAIL (S), GUIDE 771 3-065-830-01 SPRING, S RATCHET
752 3-947-503-01 SCREW (M1.4) 772 X-3951-288-1 TABLE (T) ASSY, REEL
753 A-7096-416-B BASE (S) BLOCK ASSY, GUIDE 773 3-065-819-01 SPRING, TG1 ARM
754 A-7096-415-A BASE (T) BLOCK ASSY, GUIDE 774 3-065-821-01 RAIL (T), GUIDE
755 A-7096-426-A CHASSIS ASSY, LS 775 X-3951-289-1 TABLE (S) ASSY, REEL
766 A-7096-417-A SOFT ASSY, T Q001 8-729-907-25 PHOTO TRANSISTOR PT4850F (TAPE TOP)
767 3-071-650-01 SCREW (M1.7) (S) Q002 8-729-907-25 PHOTO TRANSISTOR PT4850F (TAPE END)
768 3-065-832-01 PLATE, LS CAM S001 1-692-614-11 SWITCH, PUSH (3 KEY) (REC PROOF)
769 3-065-828-01 ARM, S RATCHET S002 1-572-688-11 SWITCH, PUSH LEVER (1 KEY) (C. C. LOCK)
770 3-065-829-01 PLATE, S RATCHET (RE)
5-11
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
807 813
M902
812 802
815
821 M903
820
822
806
823
802
808
818
804
803
Mechanical chassis
block assembly-2
(See page 5-13.)
801
Ref. No. Part No. Description Ref. No. Part No. Description
801 A-7096-422-A BASE ASSY, DRUM 814 3-065-881-01 SPRING, P PRESSURE PLATE
802 3-947-503-01 SCREW (M1.4) 815 3-065-934-01 HLW CUT 0.98X3X0.25
803 3-065-928-01 SPACER, GROUND 816 1-786-096-11 SWITCH, ROTARY
804 3-065-927-01 GROUND, DRUM 817 3-065-898-01 SPRING, EJECT ARM
805 3-065-932-01 PAN (2 MAIN M1.4X1.6), CAMERA 818 3-065-870-01 ROLLER, LS GUIDE
5-12
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
860
863
861
859
862
857
864
858
865
856
853 855
866
854
852
851
867
868
Ref. No. Part No. Description Ref. No. Part No. Description
851 3-065-920-01 ARM, HC DRIVE 860 7-624-101-04 STOP RING 1.2 (E TYPE)
852 3-065-913-01 GEAR (4), LD 861 A-7096-412-A GEAR (T) ASSY, GUIDE
853 3-065-914-01 SHEET, COVER 862 X-3951-307-1 PLATE ASSY, M SLIDE
854 3-065-917-01 GEAR (1), CAM RELAY 863 X-3951-305-1 ARM ASSY, LS
855 3-065-934-01 HLW CUT 0.98X3X0.25 864 3-065-901-01 ROLLER, LS ARM
856 3-065-915-01 GEAR (1), CAM 865 3-065-916-01 GEAR (2), CAM
857 3-065-878-01 PLATE (S), GUIDE LOCK 866 3-065-919-01 ARM, T1 LIMITTER
858 3-065-932-01 PAN (2 MAIN M1.4X1.6), CAMERA 867 X-3951-308-1 ARM ASSY, GL
859 A-7096-413-A GEAR (S) ASSY, GUIDE 868 X-3951-300-2 CHASSIS ASSY, MECHANICAL
5-13
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
CD-465 FP-300 FP-301 FP-302 FP-792 FP-802 PD-204 (TYPE C)
IC951 A-7013-219-A CCD BLOCK ASSY (CCD IMAGER) (Note) < SWITCH >
(TRV128/TRV228/TRV328/TRV428)
IC951 A-7013-276-A CCD BLOCK ASSY (CCD IMAGER) (Note) S001 1-692-614-11 SWITCH, PUSH (3 KEY) (REC PROOF)
(TRV228E/TRV428E) S002 1-572-688-11 SWITCH, PUSH LEVER (1 KEY) (C.C. LOCK)
Q951 8-729-117-73 TRANSISTOR 2SC4178-F14 C6001 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C6002 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
< RESISTOR > C6003 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C6004 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
R952 1-208-635-11 METAL CHIP 10 0.5% 1/16W C6005 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
R953 1-218-965-11 RES-CHIP 10K 5% 1/16W
C6006 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C6007 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
FP-300 FLEXIBLE BOARD (Not Supplied) C6009 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
******************** C6010 1-164-739-11 CERAMIC CHIP 560PF 5% 50V
C6011 1-163-023-00 CERAMIC CHIP 0.015uF 10% 50V
< PHOTO TRANSISTOR >
C6012 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
Q001 8-729-907-25 PHOTO TRANSISTOR PT4850F (TAPE TOP) C6013 1-100-371-11 CERAMIC CHIP 12PF 5% 3.15KV
C6015 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C6019 1-104-847-11 TANTAL. CHIP 22uF 20% 4V
FP-301 FLEXIBLE BOARD (Not Supplied) C6020 1-110-457-11 ELECT CHIP 3.3uF 20% 25V
********************
C6022 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
< DIODE > C6024 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C6026 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
D001 8-719-988-42 DIODE GL453S (TAPE LED) C6027 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C6028 1-115-407-11 ELECT CHIP 10uF 16V
R6005 1-216-824-11 METAL CHIP 1.8K 5% 1/10W < FERRITE BEAD >
R6009 1-218-975-11 RES-CHIP 68K 5% 1/16W
R6010 1-218-969-11 RES-CHIP 22K 5% 1/16W FB6001 1-414-760-21 FERRITE, EMI (SMD)(1608)
R6012 1-208-707-11 METAL CHIP 10K 0.5% 1/16W
R6013 1-208-935-11 METAL CHIP 100K 0.5% 1/16W < IC >
RB6003 1-234-372-21 RES, NETWORK 100 x 4 (1005) Q6002 6-550-065-01 TRANSISTOR CPH5504-TL-E
Q6004 8-729-054-48 TRANSISTOR UP04601008S0
< TRANSFORMER > Q6005 8-729-054-48 TRANSISTOR UP04601008S0
Q6008 6-550-242-01 TRANSISTOR DTC114EMT2L
0 T6001 1-435-786-31 TRANSFORMER, INVERTER Q6009 6-550-232-01 TRANSISTOR 2SA2029T2LQ/R
C758 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V < CAPACITOR >
(TRV328/TRV428/TRV428E)
C759 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V C002 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
(TRV328/TRV428/TRV428E) C003 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
C053 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
< CONNECTOR > C054 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C055 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
CN755 1-750-361-21 CONNECTOR, FFC/FPC (ZIF) 30P
C056 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V
< DIODE > C057 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16V
C058 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
D751 6-500-044-01 DIODE DF6A6.8FU (TE85R) C059 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
D752 6-500-044-01 DIODE DF6A6.8FU (TE85R) C060 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
D753 8-719-060-65 DIODE DCC3810 (IR EMITTER)
D754 8-719-060-65 DIODE DCC3810 (IR EMITTER) C062 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
D755 6-500-044-01 DIODE DF6A6.8FU (TE85R) C063 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C064 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
D759 6-500-506-01 DIODE TLRMV1021 (T15SOY, F) (TALLY) C065 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C066 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
< FERRITE BEAD >
C067 1-127-988-81 CERAMIC CHIP 15000PF 10% 16V
FB751 1-414-760-21 INDUCTOR, FERRITE BEAD C068 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
(TRV328/TRV428/TRV428E) C069 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C070 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
< IC > C071 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
IC751 6-704-975-01 IC RPM7240-V4 C072 1-127-772-81 CERAMIC CHIP 33000PF 10% 10V
(TRV228/TRV228E/TRV428/TRV428E) C073 1-165-875-11 CERAMIC CHIP 10uF 10% 10V
C075 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
< JACK > C076 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C078 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
J751 1-778-518-11 CONNECTOR, EXTERNAL (S VIDEO OUT)
J752 1-778-040-11 JACK, SMALL TYPE (A/V OUT) C079 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
J753 1-817-944-11 JACK, SMALL TYPE (RFU DC OUT) C080 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C081 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V
< TRANSISTOR > C082 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C083 1-125-827-91 CERAMIC CHIP 1uF 10% 25V
Q751 8-729-023-22 TRANSISTOR 2SD2114K
C084 1-125-827-91 CERAMIC CHIP 1uF 10% 25V
< RESISTOR > C085 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
C086 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
R752 1-216-806-11 METAL CHIP 56 5% 1/10W C087 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
R753 1-216-806-11 METAL CHIP 56 5% 1/10W C088 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
R761 1-216-864-11 SHORT CHIP 0
R763 1-216-821-11 METAL CHIP 1K 5% 1/10W C089 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C090 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
< SENSOR > C091 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C094 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
SE751 1-476-807-41 SENSOR, ANGULAR VELOCITY (YAW) C095 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
(TRV328/TRV428/TRV428E)
SE752 1-476-807-31 SENSOR, ANGULAR VELOCITY (PITCH) C096 1-119-749-11 TANTAL. CHIP 33uF 20% 4V
(TRV328/TRV428/TRV428E) C097 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C098 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C099 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V
C100 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
5-16
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
VC-341
Ref. No. Part No. Description Ref. No. Part No. Description
C105 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V C306 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C106 1-117-720-11 CERAMIC CHIP 4.7uF 10V C307 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C309 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
C107 1-164-506-11 CERAMIC CHIP 4.7uF 16V C310 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C108 1-164-505-11 CERAMIC CHIP 2.2uF 16V C320 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C109 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C152 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C322 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C156 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C323 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C324 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
C157 1-127-861-11 CERAMIC CHIP 2.2uF 10% 16V C325 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C158 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V C326 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50V
C160 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C161 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C328 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C163 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C329 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C332 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C164 1-164-848-11 CERAMIC CHIP 8PF 0.5PF 50V C333 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C165 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V C334 1-100-252-11 CERAMIC CHIP 0.1uF 10% 6.3V
C166 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C167 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C335 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C168 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C339 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C401 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C169 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C404 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C170 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C406 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C171 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C172 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C407 1-100-246-11 CERAMIC CHIP 0.001uF 10% 50V
C173 1-164-935-11 CERAMIC CHIP 470PF 10% 50V C408 1-100-249-11 CERAMIC CHIP 0.01uF 10% 16V
C409 1-100-251-11 CERAMIC CHIP 0.047uF 10% 10V
C176 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C410 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C177 1-104-847-11 TANTAL. CHIP 22uF 20% 4V C411 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C179 1-100-696-91 CERAMIC CHIP 1uF 10% 6.3V
C202 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C412 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C203 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V C413 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C415 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C204 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V C417 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C205 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C420 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C206 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C207 1-164-935-11 CERAMIC CHIP 470PF 10% 50V C423 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C208 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C424 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C425 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C209 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C426 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C210 1-165-708-11 ELECT 47uF 20% 6.3V C427 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V
C211 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V (TRV228E/TRV428E)
C212 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
C214 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C428 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
(TRV228E/TRV428E)
C215 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C429 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C217 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V C430 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C218 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C431 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C251 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C432 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C252 1-117-720-11 CERAMIC CHIP 4.7uF 10V
C433 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C276 1-110-666-11 ELECT CHIP 22uF 20% 6.3V C434 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
(TRV328/TRV428/TRV428E) C435 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V
C278 1-110-666-11 ELECT CHIP 22uF 20% 6.3V C436 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
(TRV328/TRV428/TRV428E) C437 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C280 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
(TRV328/TRV428/TRV428E) C439 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C281 1-100-252-11 CERAMIC CHIP 0.1uF 10% 6.3V C441 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
(TRV328/TRV428/TRV428E) C442 1-164-935-11 CERAMIC CHIP 470PF 10% 50V
C282 1-100-251-11 CERAMIC CHIP 0.047uF 10% 10V C443 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(TRV328/TRV428/TRV428E) C444 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C283 1-100-251-11 CERAMIC CHIP 0.047uF 10% 10V C445 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
(TRV328/TRV428/TRV428E) C481 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C301 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V C482 1-104-752-11 TANTAL. CHIP 33uF 20% 6.3V
C302 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C483 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C303 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C484 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C304 1-164-392-11 CERAMIC CHIP 390PF 5% 50V
C486 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
5-17
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
VC-341
Ref. No. Part No. Description Ref. No. Part No. Description
C487 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V C807 1-124-779-00 ELECT CHIP 10uF 20% 16V
C488 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C808 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C489 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C810 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C490 1-164-874-11 CERAMIC CHIP 100PF 5% 50V C811 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
C812 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C491 1-164-878-11 CERAMIC CHIP 150PF 5% 50V
C492 1-164-872-11 CERAMIC CHIP 82PF 5% 50V C814 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C493 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C815 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C494 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C816 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C495 1-164-874-11 CERAMIC CHIP 100PF 5% 50V C817 1-124-779-00 ELECT CHIP 10uF 20% 16V
C818 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
C496 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C497 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C819 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C498 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V C820 1-126-602-11 ELECT CHIP 3.3uF 20% 50V
C500 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C821 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
C505 1-100-249-11 CERAMIC CHIP 0.01uF 10% 16V C822 1-127-715-91 CERAMIC CHIP 0.22uF 10% 16V
C823 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C507 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C508 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C825 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C509 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V C826 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C513 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V C828 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C514 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C829 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C830 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C515 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C601 1-100-249-11 CERAMIC CHIP 0.01uF 10% 16V C831 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V
C602 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C832 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C603 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C833 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C604 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C834 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C835 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C605 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C606 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C836 1-127-715-91 CERAMIC CHIP 0.22uF 10% 16V
C607 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C837 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C609 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C839 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C610 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C840 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C841 1-124-779-00 ELECT CHIP 10uF 20% 16V
C611 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C614 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C842 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C615 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C843 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C616 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C844 1-164-870-11 CERAMIC CHIP 68PF 5% 50V
C617 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C845 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
(TRV328/TRV428/TRV428E) C846 1-126-209-11 ELECT CHIP 100uF 20% 4V
C617 1-218-977-11 RES-CHIP 100K 5% 1/16W C847 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
(Note) (TRV128/TRV228/TRV228E) C848 1-126-209-11 ELECT CHIP 100uF 20% 4V
C618 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C849 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
(TRV328/TRV428/TRV428E) C850 1-100-696-91 CERAMIC CHIP 1uF 10% 6.3V
C618 1-218-977-11 RES-CHIP 100K 5% 1/16W
(Note) (TRV128/TRV228/TRV228E) < CONNECTOR >
C619 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C620 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V CN002 1-794-998-31 PIN, CONNECTOR 20P
CN004 1-779-328-21 CONNECTOR, FFC/FPC 8P
C622 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V CN005 1-779-335-21 CONNECTOR, FFC/FPC 22P
C623 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V CN006 1-766-677-21 CONNECTOR, FFC/FPC 16P
C624 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V CN007 1-766-677-21 CONNECTOR, FFC/FPC 16P
C708 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C709 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V CN008 1-794-057-21 PIN, CONNECTOR (PC BOARD) 2P
CN009 1-818-072-11 CONNECTOR, FFC/FPC (ZIF) 30P
C710 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V CN053 1-573-806-21 PIN, CONNECTOR (1.5MM)(SMD) 6P
C711 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V CN151 1-779-331-11 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 14P
C712 1-164-856-81 CERAMIC CHIP 18PF 5% 50V CN201 1-750-360-21 CONNECTOR, FFC/FPC (ZIF) 24P
C713 1-100-249-11 CERAMIC CHIP 0.01uF 10% 16V
C714 1-164-856-81 CERAMIC CHIP 18PF 5% 50V * CN401 1-580-055-21 PIN, CONNECTOR (SMD) 2P
CN402 1-766-646-21 CONNECTOR, FFC/FPC 10P
C715 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V CN403 1-816-179-11 FFC/CONNECTOR, FPC (ZIF) 22P
C801 1-124-778-00 ELECT CHIP 22uF 20% 6.3V CN404 1-766-345-21 CONNECTOR, FFC/FPC 15P
C802 1-124-779-00 ELECT CHIP 10uF 20% 16V CN481 1-766-647-21 CONNECTOR, FFC/FPC 11P
C805 1-124-779-00 ELECT CHIP 10uF 20% 16V
C806 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
FB401 1-414-760-21 FERRITE, EMI (SMD) (1608) Q001 8-729-402-84 TRANSISTOR XN4601
FB481 1-414-228-11 INDUCTOR, FERRITE BEAD Q002 6-550-242-01 TRANSISTOR DTC114EMT2L
FB482 1-414-228-11 INDUCTOR, FERRITE BEAD Q051 6-550-237-01 TRANSISTOR 2SC5658T2LQ/R
FB601 1-414-760-21 FERRITE, EMI (SMD) (1608) Q052 6-550-404-01 TRANSISTOR UPA1858GR-9JG-E2-A
Q053 8-729-101-07 TRANSISTOR 2SB798-DL
< IC >
Q054 6-550-234-01 TRANSISTOR UNR32A300LS0
IC001 6-702-302-01 IC TK11133CSCL-G Q055 6-550-406-01 TRANSISTOR MCH3335-S-TL-E
IC051 6-705-264-01 IC MB44A120BPFV-G-BND-ERE1 Q056 6-550-559-01 TRANSISTOR XN0NE9200LS0
IC151 8-752-417-70 IC CXD2444AR-T4 Q057 6-550-559-01 TRANSISTOR XN0NE9200LS0
IC152 8-759-699-92 IC AD80013AJSTRL Q058 6-550-559-01 TRANSISTOR XN0NE9200LS0
IC201 8-759-637-96 IC uPD16877MA-6A5-E2
Q059 6-550-559-01 TRANSISTOR XN0NE9200LS0
IC202 8-759-681-42 IC NJM12902V (TE2) Q060 6-550-559-01 TRANSISTOR XN0NE9200LS0
IC251 8-759-713-19 IC BH2222FV-E2 Q061 6-550-559-01 TRANSISTOR XN0NE9200LS0
IC271 8-759-489-19 IC uPC6756GR-8JG-E2 Q062 6-550-560-01 TRANSISTOR CPH5819-TL-E
(TRV328/TRV428/TRV428E) Q063 8-729-101-07 TRANSISTOR 2SB798-DL
IC301 8-759-677-85 IC MB87M1011PFF-G-BND
IC302 6-705-530-01 IC BU3097-03FV-E2 Q064 6-550-237-01 TRANSISTOR 2SC5658T2LQ/R
Q065 6-550-232-01 TRANSISTOR 2SA2029T2LQ/R
IC401 6-705-676-01 IC TB6550FG (O, EB) Q066 6-550-237-01 TRANSISTOR 2SC5658T2LQ/R
IC481 8-752-093-69 IC CXA3265R-T4 Q067 6-550-232-01 TRANSISTOR 2SA2029T2LQ/R
IC601 6-803-730-01 IC MB91194APFF-G-153-BNDE1 Q068 6-550-237-01 TRANSISTOR 2SC5658T2LQ/R
IC602 6-705-122-01 IC BR25C320FV-WE2
IC701 6-803-798-01 IC MB89097PFV-G-170-BND-ERE1 Q069 8-729-053-52 TRANSISTOR HN1C01FE-Y/GR (TPLR3)
Q070 8-729-053-52 TRANSISTOR HN1C01FE-Y/GR (TPLR3)
IC801 6-704-790-01 IC AN12985A-VB Q071 6-550-232-01 TRANSISTOR 2SA2029T2LQ/R
Q072 8-729-053-52 TRANSISTOR HN1C01FE-Y/GR (TPLR3)
< COIL > Q073 8-729-053-54 TRANSISTOR HN1A01FE-Y/GR (TPLR3)
Q302 6-550-383-01 TRANSISTOR HN4A71FK (TE85R) R083 1-218-949-11 RES-CHIP 470 5% 1/16W
Q304 8-729-054-48 TRANSISTOR UP04601008S0 R085 1-218-977-11 RES-CHIP 100K 5% 1/16W
Q306 6-550-232-01 TRANSISTOR 2SA2029T2LQ/R R086 1-218-973-11 RES-CHIP 47K 5% 1/16W
Q401 6-550-283-01 TRANSISTOR UNR32A600LS0 R087 1-218-977-11 RES-CHIP 100K 5% 1/16W
Q481 8-729-047-19 TRANSISTOR 2SA1965-S-TL R089 1-218-977-11 RES-CHIP 100K 5% 1/16W
5-20
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
VC-341
Ref. No. Part No. Description Ref. No. Part No. Description
R306 1-218-949-11 RES-CHIP 470 5% 1/16W R484 1-218-970-11 RES-CHIP 27K 5% 1/16W
R307 1-218-962-11 RES-CHIP 5.6K 5% 1/16W
R487 1-218-970-11 RES-CHIP 27K 5% 1/16W
R308 1-218-953-11 RES-CHIP 1K 5% 1/16W R488 1-218-945-11 RES-CHIP 220 5% 1/16W
R309 1-218-963-11 RES-CHIP 6.8K 5% 1/16W R489 1-218-945-11 RES-CHIP 220 5% 1/16W
R310 1-218-959-11 RES-CHIP 3.3K 5% 1/16W R490 1-218-946-11 RES-CHIP 270 5% 1/16W
R311 1-218-941-81 RES-CHIP 100 5% 1/16W R491 1-218-945-11 RES-CHIP 220 5% 1/16W
R314 1-218-967-11 RES-CHIP 15K 5% 1/16W
R492 1-218-971-11 RES-CHIP 33K 5% 1/16W
R315 1-218-952-11 RES-CHIP 820 5% 1/16W R493 1-218-958-11 RES-CHIP 2.7K 5% 1/16W
R316 1-218-966-11 RES-CHIP 12K 5% 1/16W R494 1-218-958-11 RES-CHIP 2.7K 5% 1/16W
R317 1-218-949-11 RES-CHIP 470 5% 1/16W R495 1-208-939-11 METAL CHIP 150K 0.5% 1/16W
R318 1-218-945-11 RES-CHIP 220 5% 1/16W R601 1-218-941-81 RES-CHIP 100 5% 1/16W
R319 1-218-962-11 RES-CHIP 5.6K 5% 1/16W
R602 1-218-965-11 RES-CHIP 10K 5% 1/16W
R320 1-218-966-11 RES-CHIP 12K 5% 1/16W R616 1-218-953-11 RES-CHIP 1K 5% 1/16W
R321 1-218-946-11 RES-CHIP 270 5% 1/16W R619 1-218-953-11 RES-CHIP 1K 5% 1/16W
R322 1-218-946-11 RES-CHIP 270 5% 1/16W R636 1-218-977-11 RES-CHIP 100K 5% 1/16W
R323 1-218-966-11 RES-CHIP 12K 5% 1/16W R704 1-218-973-11 RES-CHIP 47K 5% 1/16W
R324 1-218-966-11 RES-CHIP 12K 5% 1/16W
R707 1-208-935-11 METAL CHIP 100K 0.5% 1/16W
R325 1-218-946-11 RES-CHIP 270 5% 1/16W R708 1-218-989-11 RES-CHIP 1M 5% 1/16W
R327 1-218-966-11 RES-CHIP 12K 5% 1/16W R709 1-219-570-11 METAL CHIP 10M 5% 1/10W
R328 1-218-946-11 RES-CHIP 270 5% 1/16W R710 1-218-985-11 RES-CHIP 470K 5% 1/16W
R330 1-218-972-11 RES-CHIP 39K 5% 1/16W R711 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
R331 1-218-989-11 RES-CHIP 1M 5% 1/16W
R712 1-218-965-11 RES-CHIP 10K 5% 1/16W
R332 1-218-967-11 RES-CHIP 15K 5% 1/16W R713 1-218-990-11 SHORT CHIP 0
R333 1-218-966-11 RES-CHIP 12K 5% 1/16W R714 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R334 1-218-949-11 RES-CHIP 470 5% 1/16W R715 1-218-953-11 RES-CHIP 1K 5% 1/16W
R335 1-218-953-11 RES-CHIP 1K 5% 1/16W R716 1-218-989-11 RES-CHIP 1M 5% 1/16W
R336 1-218-965-11 RES-CHIP 10K 5% 1/16W
R717 1-218-949-11 RES-CHIP 470 5% 1/16W
R339 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R718 1-218-977-11 RES-CHIP 100K 5% 1/16W
R341 1-218-953-11 RES-CHIP 1K 5% 1/16W R806 1-218-957-11 RES-CHIP 2.2K 5% 1/16W
R401 1-218-973-11 RES-CHIP 47K 5% 1/16W R807 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
R402 1-218-983-11 RES-CHIP 330K 5% 1/16W R810 1-218-965-11 RES-CHIP 10K 5% 1/16W
R403 1-218-949-11 RES-CHIP 470 5% 1/16W
R811 1-218-973-11 RES-CHIP 47K 5% 1/16W
R404 1-218-946-11 RES-CHIP 270 5% 1/16W R812 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R405 1-218-990-11 SHORT CHIP 0 R815 1-218-979-11 RES-CHIP 150K 5% 1/16W
R409 1-216-808-11 METAL CHIP 82 5% 1/10W R817 1-218-985-11 RES-CHIP 470K 5% 1/16W
R410 1-216-789-11 METAL CHIP 2.2 5% 1/10W R818 1-218-990-11 SHORT CHIP 0
R411 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R819 1-218-952-11 RES-CHIP 820 5% 1/16W
R412 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R413 1-218-965-11 RES-CHIP 10K 5% 1/16W < COMPOSITION CIRCUIT BLOCK >
(TRV228E/TRV428E)
R413 1-218-990-11 SHORT CHIP 0 RB201 1-234-375-21 RES, NETWORK 1K x 4 (1005)
(TRV128/TRV228/TRV328/TRV428) RB202 1-234-379-21 RES, NETWORK 22K x 4 (1005)
R414 1-218-967-11 RES-CHIP 15K 5% 1/16W RB203 1-234-380-21 RES, NETWORK 47K x 4 (1005)
(TRV128/TRV228/TRV328/TRV428) RB271 1-234-379-21 RES, NETWORK 22K x 4 (1005)
R414 1-218-973-11 RES-CHIP 47K 5% 1/16W (TRV328/TRV428/TRV428E)
(TRV228E/TRV428E) RB301 1-234-378-21 RES, NETWORK 10K x 4 (1005)
R424 1-218-965-11 RES-CHIP 10K 5% 1/16W RB302 1-234-376-21 RES, NETWORK 2.2K x 4 (1005)
R426 1-218-967-11 RES-CHIP 15K 5% 1/16W RB401 1-234-378-21 RES, NETWORK 10K x 4 (1005)
R427 1-218-965-11 RES-CHIP 10K 5% 1/16W RB481 1-234-379-21 RES, NETWORK 22K x 4 (1005)
(TRV228E/TRV428E) RB482 1-234-383-21 RES, NETWORK 470K x 4 (1005)
R427 1-218-990-11 SHORT CHIP 0 RB483 1-234-376-21 RES, NETWORK 2.2K x 4 (1005)
(TRV128/TRV228/TRV328/TRV428)
R431 1-216-864-11 SHORT CHIP 0 RB601 1-234-381-21 RES, NETWORK 100K x 4 (1005)
RB605 1-234-375-21 RES, NETWORK 1K x 4 (1005)
R481 1-218-936-11 RES-CHIP 39 5% 1/16W RB606 1-234-378-21 RES, NETWORK 10K x 4 (1005)
(TRV228E/TRV428E) RB608 1-234-384-11 RES, NETWORK 1M x 4 (1005)
R481 1-218-938-11 RES-CHIP 56 5% 1/16W RB610 1-234-377-21 RES, NETWORK 4.7K x 4 (1005)
(TRV128/TRV228/TRV328/TRV428) (TRV328/TRV428/TRV428E)
R482 1-218-950-11 RES-CHIP 560 5% 1/16W
R483 1-218-941-81 RES-CHIP 100 5% 1/16W RB611 1-234-381-21 RES, NETWORK 100K x 4 (1005)
5-21
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
VC-341
Ref. No. Part No. Description Ref. No. Part No. Description
RB612 1-234-380-21 RES, NETWORK 47K x 4 (1005)
RB613 1-234-377-21 RES, NETWORK 4.7K x 4 (1005)
RB701 1-234-383-21 RES, NETWORK 470K x 4 (1005)
RB703 1-234-375-21 RES, NETWORK 1K x 4 (1005)
5-22
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
Other accessories
3-087-918-11 MANUAL, INSTRUCTION (ENGLISH)
(TRV128: US, CND, E/TRV228/TRV328/TRV428)
3-087-918-21 MANUAL, INSTRUCTION (FRENCH)
(TRV128: CND/TRV328: CND)
3-087-918-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE)
Battery Holder
3-083-973-01 (TRV128: E, MX/TRV228/TRV328: E/TRV428)
3-087-918-41 MANUAL, INSTRUCTION (TRADITIONAL CHINESE)
Wireless Remote Commander (TRV228)
RMT-833 (1)
3-087-918-51 MANUAL, INSTRUCTION (KOREA) (TRV428)
1-477-898-11 (EXCEPT TRV128/
3-087-918-61 MANUAL, INSTRUCTION (ARABIC) (TRV228)
TRV228E: E1/TRV328/TRV428E: E1)
3-087-919-11 MANUAL, INSTRUCTION (ENGLISH)
1-477-898-31
(TRV228E: E2/TRV428E: E2) (TRV228E: AEP, UK, E/TRV428E: AEP, E, AUS, HK, JE)
3-087-919-21 MANUAL, INSTRUCTION (FRENCH)
(Note) E1: No indication of country of origin. (TRV228E: AEP, E/TRV428E: AEP, E, JE)
E2: There is indication of country of origin. 3-087-919-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE)
(TRV228E: AEP/TRV428E: AEP)
3-087-919-41 MANUAL, INSTRUCTION (ITALIAN, GREEK)
(TRV228E: AEP/TRV428E: AEP)
3-087-919-51 MANUAL, INSTRUCTION (GERMAN, DUTCH)
(TRV228E: AEP/TRV428E: AEP)
3-087-919-61 MANUAL, INSTRUCTION (SWEDISH, RUSSIAN)
(TRV228E: NE/TRV428E: NE, JE)
3-087-919-71 MANUAL, INSTRUCTION (DANISH, FINNISH)
21-pin adaptor (1) (TRV228E: NE/TRV428E: NE)
1-770-783-21 (AEP, UK, NE, EE) 3-087-919-81 MANUAL, INSTRUCTION (POLISH, CZECH)
(TRV228E: EE/TRV428E: EE)
3-087-919-91 MANUAL, INSTRUCTION (HUNGALIAN, SLOVAK)
(TRV228E: EE/TRV428E: EE)
3-087-920-11 MANUAL, INSTRUCTION (ARABIC, PERSIAN)
(TRV228E: E/TRV428E: E)
3-087-920-21 MANUAL, INSTRUCTION (TRADITIONAL CHINESE)
(TRV428E: HK)
Conversion 2P adaptor (1) Conversion 2P adaptor (1) 3-087-920-31 MANUAL, INSTRUCTION (SIMPLIFIED CHINESE)
0 1-569-008-12 (E, HK) 0 1-569-007-12 (JE) (TRV228E: E/TRV428E: E, JE)
5-23E
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
Camera
Operations Guide
Read this first
CCD-TRV128/TRV228/TRV328/TRV428
DCR-TRV260/TRV265
Declaration of Conformity
This symbol is intended to alert the Trade Name: SONY
user to the presence of uninsulated Model No.: DCR-TRV260
“dangerous voltage” within the Responsible Party: Sony Electronics Inc.
product’s enclosure that may be of Address: 680 Kinderkamack Road, Oradell,
sufficient magnitude to constitute a NJ 07649 U.S.A.
risk of electric shock to persons. Telephone No.: 201-930-6972
This device complies with Part 15 of the FCC Rules.
This symbol is intended to alert the Operation is subject to the following two conditions:
user to the presence of important (1) This device may not cause harmful interference,
operating and maintenance and (2) this device must accept any interference
(servicing) instructions in the received, including interference that may cause
literature accompanying the undesired operation.
appliance.
Owner’s Record
The model and serial numbers are located on the
bottom. Record the serial number in the space
For customers in the U.S.A. and provided below. Refer to these numbers whenever you
call upon your Sony dealer regarding this product.
CANADA Model No. -TRV
Serial No.
CAUTION Model No.AC-
TO PREVENT ELECTRIC SHOCK, MATCH WIDE Serial No.
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
2
CAUTION recording of such materials may be contrary to the
You are cautioned that any changes or modifications copyright laws.
not expressly approved in this manual could void your
authority to operate this equipment. Notes on the LCD panel, viewfinder, and
lens
b Note: • The LCD screen and the viewfinder are
This equipment has been tested and found to comply manufactured using extremely high-precision
with the limits for a Class B digital device, pursuant to technology, so over 99.99% of the pixels are
Part 15 of the FCC Rules. operational for effective use.
These limits are designed to provide reasonable However, there may be some tiny black points and/
protection against harmful interference in a residential or bright points (white, red, blue, or green in color)
installation. This equipment generates, uses, and can that appear constantly on the LCD screen and the
radiate radio frequency energy and, if not installed and viewfinder.
used in accordance with the instructions, may cause These points are normal results of the manufacturing
harmful interference to radio communications. process and do not affect the recording in any way.
However, there is no guarantee that interference will • Exposing the LCD screen, the viewfinder, or the lens
not occur in a particular installation. If this equipment to direct sunlight for long periods of time may cause
does cause harmful interference to radio or television malfunctions. Be careful when placing the camera
reception, which can be determined by turning the near a window or outdoors.
• Do not aim at the sun. Doing so might cause your
equipment off and on, the user is encouraged to try to
camcorder to malfunction. Take pictures of the sun
correct the interference by one or more of the
only in low light conditions, such as at dusk.
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and Note on connecting other device
receiver. Before connecting your camcorder to other device
– Connect the equipment to an outlet on a circuit such as a VCR or a computer with an USB or i.LINK
different from that to which the receiver is cable, be sure to insert the connector plug in the proper
connected. direction. If you insert the connector plug forcibly in
– Consult a Sony dealer or an experienced radio/TV the wrong direction, the terminal may be damaged.
technician for help. This may cause a malfunction of your camcorder.
The interface cable supplied must be used with the
equipment in order to comply with the limits for a Notes on using this manual
digital device pursuant to Subpart B of Part 15 of FCC • The images of the LCD screen and the viewfinder
Rules. used on this manual are captured using a digital still
camera, and thus may appear different from what
you see.
• In this instruction manual, each model is indicated as
Notes on use follows.
Note on a cassette tape CCD-TRV128: TRV128
You can use standard 8 mm and Hi8 , CCD-TRV228: TRV228
Digital8 video cassettes on your camcorder. See CCD-TRV328: TRV328
page 82 for details. CCD-TRV428: TRV428
DCR-TRV260: TRV260
DCR-TRV265: TRV265
Notes on recording Instructions with no specific model names are for all
• Before starting to record, test the recording function models.
to make sure the picture and sound are recorded Instructions with specific model names are for the
without any problems. indicated models only.
• Compensation for the contents of recordings cannot Before you start reading this manual, check the
be provided, even if recording or playback is not model name of your camcorder.
possible due to a malfunction of the camcorder, etc. • The illustrations used on this manual are based on
• TV color systems differ depending on the country/ the model DCR-TRV265.
regions. To view your recordings on a TV, you need
an NTSC system-based TV.
• Television programs, films, video tapes, and other
materials may be copyrighted. Unauthorized
,continued
3
Notes on using the camcorder
• Hold your camcorder correctly.
Battery pack
4
Table of Contents CCD-TRV128:
CCD-TRV228:
TRV128 CCD-TRV428:
TRV228 DCR-TRV260:
TRV428
TRV260
CCD-TRV328: TRV328 DCR-TRV265: TRV265
Read this first ............................................................................................. 2
Getting started
Step 1: Checking supplied items.............................................................. 11
Step 2: Charging the battery pack............................................................ 12
Using an outside power source ................................................................................. 15
Recording
Recording movies .................................................................................... 21
Recording for a longer time ....................................................................................... 23
Using zoom ............................................................................................................... 23
Using the built-in light ................................................................................................ 23
Recording in mirror mode ......................................................................................... 24
Superimposing the date and time on pictures ( TRV128/228/328/428) ............. 25
5
Superimposing a title................................................................................ 31
Searching for the last scene of the most recent recording
– END SEARCH ................................................................................. 33
Playback
Viewing pictures recorded on a tape........................................................ 34
Playing back in various modes .................................................................................. 35
6
Advanced operations
Troubleshooting
Troubleshooting .................................74
Customizing Your
Warning indicators and messages .....79
Camcorder
Changing the menu settings ..............43
Additional Information
Using the (MANUAL SET) menu
– PROGRAM AE/P EFFECT, Using your camcorder abroad ............81
etc. ...............................................44 Usable cassette tapes ........................82
Using the (CAMERA SET) menu About the “InfoLITHIUM” battery
– 16:9 WIDE/STEADYSHOT, pack ..............................................83
etc. ...............................................47
About i.LINK .......................................84
Using the (PLAYER SET)/ (VCR
Maintenance and precautions ............85
SET) menu – HiFi SOUND/EDIT,
etc. ...............................................51 Specification .......................................88
Using the (LCD SET) menu – LCD
B.L./LCD COLOR, etc. .................53 Quick Reference
Using the (TAPE SET) menu
– FRAME REC/INT.REC, etc. ......54 Identifying parts and controls .............91
Dubbing/Editing
Connecting to a VCR .........................61
Dubbing to another tape ....................63
Dubbing a tape easily – Easy Dubbing
( TRV128/228/328/428) ........64
Recording pictures from a VCR
( TRV260/265) ...........................68
Dubbing selected scenes from a tape
– Digital program editing
( TRV260/265) ...........................69
For TRV260/265:
Refer also to other operating instructions
supplied with your camcorder:
• Editing images with your computer
cComputer Applications Guide
7
Quick Start Guide
Recording movies
Window-side
OPEN/EJECT lever
b Press (rewind).
c Press (play) to
start the playback.
To stop, press .
Easy Handycam
operation
ON
Step 1: Checking
supplied items
A/V connecting cable (1)
Make sure you have following items supplied
Monaural: ( TRV128/228/328/428)
with your camcorder.
The number in parentheses indicates the number
of that item supplied.
Getting started
AC Adaptor (1)
Stereo: ( TRV260/265)
Getting started 11
Step 2: Charging the 2 Attach the battery pack by sliding it in
the direction of the arrow until it
battery pack clicks.
Battery pack
DC IN jack v mark
DC plug
4 Connect the power cord to the AC
Adaptor.
Power cord
5 Connect the power cord to the wall
AC Adaptor outlet.
To the wall outlet
12 Getting started
After charging the battery You can check the battery's current charge level
The CHG (charge) lamp turns off when the and its current remaining recording time both
battery is fully charged. Disconnect the AC during charging or when the power is turned off.
Adaptor from the DC IN jack. 1 Set the POWER switch to (CHG) OFF.
To remove the battery pack 2 Press OPEN and open the LCD panel.
3 Press DSPL/BATT INFO.
POWER switch The battery information appears for about 7
BATT (battery)
release button seconds.
Keep the button pressed to view it for about
20 seconds.
Getting started
BATTERY INFO
,continued
Getting started 13
For TRV128/228/328/428: For TRV260/265:
Battery pack Continuous Typical* Battery pack Continuous Typical*
recording recording recording recording
time time time time
NP-FM30 115 55 NP-FM30 125 65
(supplied) (supplied)
NP-FM50 185 90 NP-FM50 200 105
NP-QM71/ 445 220 NP-QM71/ 485 255
QM71D QM71D
NP-QM91/ 670 335 NP-QM91/ 725 385
QM91D QM91D
14 Getting started
b Notes
• The power will not be supplied from the battery pack
when the AC Adaptor is connected to the DC IN jack Step 3: Turning the
of your camcorder, even if its power cord is
disconnected from the wall outlet. power on
• The recording and playback time will be shorter
when you use your camcorder in low temperature.
• The CHG (charge) lamp flashes during charging, or
You need to slide the POWER switch
the battery information will not be correctly repeatedly to select the desired power mode
displayed in following conditions. to record or play.
– The battery pack is not attached correctly. When using this camcorder for the first time,
– The battery pack is damaged.
the [CLOCK SET] screen appears (p. 17).
– The battery pack is fully discharged. (For Battery
information only.)
Getting started
While pressing the green button, slide the
Using an outside power source POWER switch down.
The power turns on.
To enter the recording or playing mode, slide
the switch repeatedly until the respective lamp
for the desired power mode lights up.
You can use the AC Adaptor as the power
source when you do not want the battery to
run out. While you are using the AC Adaptor,
the battery pack will not lose its charge even
when it is attached to your camcorder.
PRECAUTION
Even if your camcorder is turned off, AC power
(house current) is still supplied to it while
connected to the wall outlet via the AC Adaptor. • CAMERA mode: To record on a tape.
• PLAY/EDIT mode: To play or edit pictures on
a tape.
Connect your camcorder as shown in
“Charging the battery pack” (p. 12).
To turn off the power
Slide the POWER switch up to (CHG) OFF.
Getting started 15
3 Turn the SEL/PUSH EXEC dial to select
Step 4: Adjusting the [LCD BRIGHT], then press the dial
(p. 53).
LCD panel and 4 Adjust the brightness of the LCD screen
viewfinder with the SEL/PUSH EXEC dial, then
press the dial.
5 Press MENU.
Adjusting the LCD panel z Tips
• If you rotate the LCD panel 180 degrees to the lens
side, you can close the LCD panel with the LCD
screen facing out.
• If you are using the battery pack for power source,
You can adjust the angle and brightness of you can adjust the brightness by selecting [LCD
the LCD panel to meet various recording B.L.] in the (LCD SET) menu (p. 53).
situations. • The recorded picture will not be affected by this
setting.
Even when there are obstructions between you
• You can turn off the operation confirmation beep by
and the subject, you can check the subject on the setting [BEEP] in the (OTHERS) menu to
LCD screen during recording by adjusting the [OFF] (p. 59).
angle of the LCD panel.
Maximum
180 degrees
You can view images using the viewfinder
when you close the LCD panel. Use the
viewfinder when the battery is running out, or
when the screen is hard to see.
Maximum
90 degrees
16 Getting started
Step 5: Setting the 3 Press MENU.
Getting started
b Note the dial.
• If you do not use your camcorder for about 3
SETUP MENU STBY
months, the built-in rechargeable button-type CLOCK SET ––:––:––
USB STREAM
battery gets discharged and the date and time LTR SIZE
LANGUAGE
settings may be cleared from the memory. In that DEMO MODE
RETURN
case, charge the rechargeable button-type battery
(p. 87) and then set the date and time again. [MENU] : END
MENU
Y M D H M
2004 JAN 1 12 : 0 0 AM
[MENU] : CANCEL
OPEN SEL/PUSH
EXEC dial
POWER
switch
6 Turn the SEL/PUSH EXEC dial to set
[Y] (year), then press the dial.
CLOCK SET STBY
,continued
Getting started 17
To check the preset date and time
For TRV128/228/328/428:
Press DATE to display the date indicator.
Step 6: Inserting a
Press TIME to display the time indicator.
Press DATE (or TIME) and then press TIME
cassette tape
(or DATE) to simultaneously display the date
You can use standard 8 mm and Hi8 ,
and time indicator.
Digital8 video cassettes on your camcorder.
To hide the date and/or time indicator, press
For details on these cassettes (such as write-
DATE and/or TIME again.
protection), See page 82.
b Notes
• Do not force the cassette into the compartment. This
may cause a malfunction of your camcorder.
• For TRV260/265:
The recording time when you use your camcorder is
half of the indicated time on Hi8 tape. If you
select the [LP] mode in the menu settings, the
recording time is 3/4 of the indicated time on
Hi8 tape.
18 Getting started
2 Insert a cassette with its window-side
Step 7: Setting the
facing up.
Window-side screen language
You can select the language to be used on the
LCD screen.
MENU
Getting started
Push the center of the
back of the cassette
lightly.
3 Press .
The cassette compartment automatically
slides back in.
OPEN SEL/PUSH POWER
EXEC dial switch
3 Press MENU.
[MENU] : END
,continued
Getting started 19
5 Turn the SEL/PUSH EXEC dial to
select [ LANGUAGE], then press
the dial.
[MENU] : END
7 Press MENU.
z Tip
• Your camcorder offers [ENG [SIMP]] (simplified
English) for when you cannot find your native
tongue among the options.
20 Getting started
Recording
2 Press OPEN and open the LCD panel.
Recording
Camera recording lamp
z Tip
• Performing Easy Handycam operation, even first
time users can record easily. For details, see page 26.
,continued
Recording 21
Indicators displayed during recording F Hi8 format
The indicators will not be recorded on the tape. This appears while recording Hi8 format
tapes.
For TRV128/228/328/428: G Time code/Tape counter (hour: minute:
second)/Tape photo recording
1 2 3 4
b Notes
60min SP REC 0:00:00 • Before changing the battery pack, slide the POWER
6 5 switch up to (CHG) OFF.
• In the default setting, if you do not operate the
camcorder for more than about 5 minutes, the power
will automatically turn off to preserve battery power
([A.SHUT OFF], p. 59). To restart recording, slide
the POWER switch down to select CAMERA, and
then press REC START/STOP.
z Tips
For TRV260/265: • To ensure smooth transition on a tape from the last
Date/time and camera settings data (p. 37) will recorded scene to the next, note the following.
not be displayed during recording. – Do not remove the cassette. (The picture will be
recorded continuously without a break even when
you turn the power off.)
1 2 3 7 – Do not record pictures in SP mode and LP mode on
the same tape.
60min SP REC 0:00:00 – Avoid stopping then recording a movie in the LP
5 mode.
• For TRV260/265:
The recording time, date, and the camera settings
data are recorded automatically on the tape without
being displayed on the screen. You can view this
information during playback by selecting [DATA
CODE] on the screen (p. 59).
22 Recording
Recording for a longer time Move the power zoom lever slightly for a
slower zoom. Move it further for a faster
zoom.
To record wider range of view
To record for a longer time Move the power zoom lever towards W.
In the (TAPE SET) menu, select [REC The subject appears farther away (Wide
MODE], then [LP] (p. 54). angle).
In the LP mode, you can record longer than To record closer view
when recording in the SP mode (2 times longer Move the power zoom lever towards T.
for TRV128/228/328/428, 1.5 times The subject appears closer (Telephoto).
longer for TRV260/265).
A tape recorded in the LP mode should be
played back only on this camcorder.
Recording
Using the built-in light
Using zoom
LIGHT
,continued
Recording 23
b Notes
• The built-in video light emits very bright light, Recording in mirror mode
which is perfectly safe in normal use. However,
avoid directly aiming the light at a subject’s eyes
from very close range.
• The battery pack discharges quickly while the built-
in light is turned on. You can turn the LCD panel towards the
• When you do not use your camcorder, turn the built-
subject so that you and your subject can share
in light off and remove the battery pack to avoid
turning on the built-in light accidentally. the image being recorded. You can also
• When flickering occurs while shooting in the utilize this function when recording yourself,
mode, press LIGHT until to keep the attention of small children
appears. attracted to the camcorder while you record
• The built-in light may turn on/off when you use the
[PROGRAM AE] or back light function while
them.
shooting in the mode.
• For TRV260/265:
The built-in light is turned off during the interval
time of Interval recording.
• When you use the conversion lens (optional), light
from the built-in light is blocked and may not
illuminate the subject properly.
b Notes
For TRV128/228/328/428:
• appears in the viewfinder and on the LCD
screen. Xz appears in the standby mode, and z
appears in the recording mode. Some of other
indicators appear mirror-reversed and others are not
displayed.
• During recording in the mirror mode, DATE and
TIME on your camcorder do not work.
24 Recording
Superimposing the date and time
on pictures ( TRV128/228/328
Recording still
/428) images
– Tape photo recording
You can record the date and/or time
displayed on the screen superimposed on the ( TRV260/265)
picture.
You can record still images. Before
recording, follow steps 1 to 7 in “Getting
started” (p. 11 - p. 19).
OPEN PHOTO
Recording
DATE TIME
CCD-TRV428
b Note
• The date and time indicators recorded manually
cannot be deleted.
z Tip
• If you do not record the date and time in the picture,
record the date and time in the black screen as the
background for about 10 seconds, then erase the date
and time indicators before starting actual recording. 2 Press OPEN and open the LCD panel.
,continued
Recording 25
3 Slide the POWER switch to select the
Recording with ease
CAMERA mode.
– Easy Handycam
4 Press EASY.
EASY lights up in blue.
26 Recording
Easy Handycam
Adjusting the
operation
ON
exposure
The exposure is adjusted automatically in the
default setting.
5 Press REC START/STOP.
Recording starts. [REC] appears on the Adjusting the exposure for backlit
LCD screen and the Camera recording lamp
lights up. Press REC START/STOP again subjects
to stop recording.
Recording
To turn the power off other light, you can adjust the exposure to
Slide the POWER switch up to (CHG) OFF. prevent the subject from becoming
shadowed.
To cancel Easy Handycam operation
Press EASY again.
b Notes
• You cannot switch from/to Easy Handycam
operation during recording.
• For TRV260/265:
During Easy Handycam operation, you cannot
connect the USB cable to your camcorder.
• For TRV260/265:
You cannot use Easy Handycam operation together
with USB Streaming.
• All the settings return to their defaults during Easy BACK LIGHT
Handycam operation. Previously made settings are
restored when you cancel Easy Handycam
operation.
Press BACK LIGHT in CAMERA mode.
. appears.
To cancel the back light function, press BACK
LIGHT again.
b Note
• The back light function is canceled when you press
EXPOSURE (p. 28).
,continued
Recording 27
Adjusting the exposure manually
Recording in dark
places
You can fix the brightness of a picture at the – NightShot plus
best exposure. When recording indoors on a
clear day, for instance, you can avoid You can record subjects in dark places (such
backlight shadows on people next to the as when capturing the face of your baby
window by manually fixing the exposure to sleeping) with this function.
that of the wall side of the room.
b Notes
• Do not use the NightShot plus function in bright
places. This may cause a malfunction.
• You cannot use the NightShot plus function together
with:
– [PROGRAM AE]
– Manual exposure
While exposure is set to manual mode, is • Adjust the focus manually when it is hard to focus
displayed in the left-hand corner of the automatically.
screen. • Do not cover the infrared port with your fingers or
other objects. Remove the conversion lens (optional)
if it is attached.
To return the setting to automatic • Depending on the shooting conditions or
circumstances, colors may not be reproduced
exposure properly.
Press EXPOSURE.
28 Recording
z Tip
• If you record subjects in complete darkness, set
[N.S. LIGHT] to [ON] in the menu settings. The Adjusting the focus
maximum shooting distance using the NightShot
Light is about 3 meters (10 feet). If you record manually
subjects in dark places (such as night scene or in
moonlight), set [N.S. LIGHT] to [OFF] in the menu
settings. You can make image color deeper (p. 50).
The focus is adjusted automatically in the
default setting.
You can adjust the focus manually according
to the recording conditions.
Use this function in the following cases.
– To record a subject behind a window covered
with raindrops.
– To record horizontal stripes.
– To record a subject with little contrast
Recording
between the subject and its background.
– When you want to focus on a subject in the
background.
,continued
Recording 29
Tips for focusing manually
• It is easier to focus on the subject when
you use the zoom function. Move the
Recording a picture
power zoom lever towards T (telephoto)
to adjust the focus, and then, towards W
using various effects
(wide angle) to adjust the zoom for
recording. FADER
• When you want to record a close-up
image of a subject, move the power zoom
lever towards W (wide angle) to fully
magnify the image, then adjust the focus.
[BLACK FADER]
[WHITE FADER]
[MOSAIC FADER]
30 Recording
[STRIPE FADER]
This feature is for
only.
TRV128/228/328/428
Superimposing a title
You can insert a title when recording.
You can select one of the 8 preset titles and
the 2 custom titles.
TITLE
[MONOTONE FADER]
When fading in, the picture gradually changes
from black-and-white to color.
When fading out, the picture gradually changes
from color to black-and-white.
Recording
1 Slide the POWER switch to select the
CAMERA mode.
TITLE STBY
CUSTOM1""
To cancel the operation OK
CREATE / EDIT
In step 2, press FADER repeatedly until the
indicator disappears. [TITLE] : END
b Notes
• For TRV260/265: 2 Turn the SEL/PUSH EXEC dial to select
You cannot use the FADER function together with: [CREATE/EDIT], then press the dial.
– Tape photo recording 3 Turn the SEL/PUSH EXEC dial to select
– [FRAME REC] (Frame recording) the column of the desired character, then
– [INT. REC] (Interval recording)
press the dial.
• Titles do not fade in or fade out. The date and time
indicator for TRV128/228/328/428 also does
not fade in or fade out.
Erase them before operating the FADER function if
they are not needed.
,continued
Recording 31
4 Turn the SEL/PUSH EXEC dial to select [POSITION] (position)
the desired character, then press the dial. You can select from 8 to 9 choices.
TITLE SET P1 STBY
S_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
ABCDE 1 2 3 4 5
FGHIJ 6 7 8 9 0
$ ¥DM£
¿iø”:
4 Turn the SEL/PUSH EXEC dial to
KLMNO ÀÈÌÒÙ
PQRST ÁÉÍÓÚ
[ C ]
[ cP2 ] select [OK], then press the dial.
UVWXY ÂÊÔÆŒ [O K]
Z& ? ! ÃÕÑçß
’ . , / – ÄÏÖÜÅ
The title appears.
[TITLE] : END
b Notes
2 Turn the SEL/PUSH EXEC dial to • If you display the menu while superimposing a title,
the title is not recorded while the menu is displayed.
select the title you want to insert, then
• When you are selecting and setting the title, the title
press the dial. displayed on the screen is not recorded.
To insert an original title, turn the SEL/ • When you superimpose a title while you are
PUSH EXEC dial to select [CUSTOM1””] recording, the beep does not sound.
or [CUSTOM2””], and press the dial, then • When you are using your camcorder on the battery
select [OK] and press the dial. pack and do not operate it for 5 minutes, the power
automatically goes off as the default setting. If you
may take 5 minutes or longer to enter characters, set
3 Change [COLOR], [SIZE], or [A.SHUT OFF] in the (OTHERS) menu to
[NEVER] (p. 59). The power will not to be turn off.
[POSITION] as necessary. Even though the power goes off, the characters you
1 Turn the SEL/PUSH EXEC dial to select have entered remain stored in memory. Turn the
[COLOR], [SIZE], or [POSITION], then power back on, then start again from step 1 to
press the dial. The selected item appears continue superimposing the title.
on the screen. • For TRV128/228/328/428:
2 Turn the SEL/PUSH EXEC dial to select The date and time, or either of them, may not be
the desired item, then press the dial. displayed depending on the size or position of the
3 Repeat steps 1 and 2 until the title is laid title.
out as desired. z Tip
[COLOR] (color) • To change a created title, select the title in step 1,
[WHITE] y [YELLOW] y then press the SEL/PUSH EXEC dial. Then reselect
[VIOLET] y [RED] y [CYAN] y the characters again.
[GREEN] y [BLUE]
[SIZE] (size)
[SMALL] y [LARGE]
(You can only select [SMALL] when
you are entering more than 13
characters.)
32 Recording
Searching for the last
scene of the most
recent recording
– END SEARCH
Recording
you have recorded on the tape.
b Note
• The END SEARCH function will not work correctly
when there is a blank section between recorded
sections on the tape.
z Tip
• When PLAY/EDIT mode is selected, you can do this
operation by pressing END SEARCH.
Recording 33
Playback
3 Press (rewind) to go to the point
you want to view.
Viewing pictures
recorded on a tape 4 Press (play) to start playback.
To pause
Press (pause) during playback. Press
(pause) or (play) to restart the
playback.
Playback stops automatically when pause mode
continues for a few minutes.
OPEN POWER
To review movies on the viewfinder
switch Close the LCD panel.
34 Playback
For TRV260/265: To view pictures at slow speed (slow
playback)*
For TRV228/428/ TRV265:
Press SLOW y on the Remote Commander
60min 0:00:00:00
during playback. To resume normal playback,
press PLAY.
* For TRV265:
Pictures output from the DV Interface cannot be
played back smoothly in the slow mode.
b Notes
• For TRV228/428:
A Remaining battery time If slow playback lasts for about 1 minute, the
B Recording mode (SP or LP) camcorder automatically returns to normal speed
playback.
C Tape transport indicator • For TRV128/228/328/428:
D Tape counter (hour: minute: second) When you play back a tape recorded in the LP mode,
noise may appear on the LCD screen in the
E Hi8 format
Playback
following cases:
This appears while playing back Hi8 format – Slow playback ( TRV228/428)
tapes. – Playback pause
F Time code (hour: minute: second: frame) – Picture search
or tape counter (hour: minute: second)
b Note
• For TRV260/265:
If you use a standard 8 mm tape, be sure to play
back the tape on your camcorder. Mosaic noise may
appear when you play back the standard 8 mm
tape on other camcorders (including another DCR-
TRV260/TRV265).
Playback 35
Playing back with 4 Play back a tape.
The following buttons can be operated.
ease (play)/ (stop)/
(fast forward)/
(pause)/
(rewind)
– Easy Handycam For TRV228/428/ TRV265:
You can operate those operations and
SLOW y on the Remote Commander.
Easy Handycam operation allows easy
playback for even first time users by
providing only the basic functions for
To cancel Easy Handycam operation
playback. Also screen font size increases for
Press EASY again.
easy viewing. Make sure you have a recorded
cassette inserted into your camcorder. b Notes
For TRV260/265:
EASY
• During Easy Handycam operation, you cannot
connect the USB cable to your camcorder.
• You cannot use Easy Handycam operation together
with USB Streaming.
z Tip
• Buttons that do not work during Easy Handycam
operation have a dot beside them on your camcorder.
Also, only menu items that are available during Easy
Handycam operation are displayed when MENU is
pressed.
3 Press EASY.
EASY lights up in blue.
Easy Handycam
operation
ON
36 Playback
Displaying the date/time and
Various playback camera settings data – Data code
functions ( TRV260/265)
You can display the recorded date on the During playback, you can view the date/time
screen. data ([DATE/TIME]) and the camera settings
data ([CAM DATA]) that are automatically
DSPL/BATT INFO POWER switch recorded while recording pictures on a tape.
Playback
MENU SEL/PUSH
3 Turn the SEL/PUSH EXEC dial to
EXEC dial select (OTHERS), then press the
dial.
COMMANDER
DISPLAY
VIDEO EDIT
RETURN
[MENU] : END
Press DSPL/BATT INFO.
The indicators appear/disappear as you press the
button.
5 Turn the SEL/PUSH EXEC dial to
select the [DATE/TIME] or [CAM
z Tips DATA], then press the dial.
• For TRV228/428/ TRV265:
You can display the screen indicators by pressing
DISPLAY on the Remote Commander.
• You can display the screen indicators during
6 Press MENU.
playback on a TV. Select the (OTHERS) menu,
60min 0:00:00:00
[DISPLAY], then [V-OUT/LCD] (p. 60).
JAN 1 2004
12:17:50PM
,continued
Playback 37
To hide the date/time or the camera
settings data
Follow steps 2 to 4, and select [OFF] in step 5.
60min 0:00:00:00
1
2
3
AUTO
100 AWB
F1.6 9dB 4
5
6
A SteadyShot off
B Exposure
C White balance
D Gain
E Shutter speed
F Aperture value
38 Playback
Connect your camcorder to a TV using the
Playing the picture on supplied A/V connecting cable as shown in
the following illustration.
a TV Connect the supplied AC Adaptor to the wall
outlet for the power supply (p. 12).
Refer also to the instruction manuals supplied
with the devices to be connected.
To copy to another tape, see page 63.
For TRV128/228/328/428:
Yellow
Playback
Black
For TRV260/265:
Yellow
White
Red
,continued
Playback 39
* When there is an S video jack on the device to be
connected, connect the S video plug to that jack
instead of using the yellow video plug. The audio Locating a scene on a
will not be output when you connect with the S video
plug alone. tape for playback
Pictures can be reproduced more faithfully with this
( TRV265)
connection.
When your TV is monaural (When your 1 During playback, press ZERO SET
TV has only one audio input jack) MEMORY on the Remote
For TRV260/265: Commander at the point you want to
Connect the yellow plug of the A/V connecting locate later on.
cable to the video input jack and connect the The tape counter is reset to “0:00:00” and
white or the red plug to the audio input jack of appears on the screen.
your TV or VCR. If the tape counter is not displayed, press
When you want to play the sound in monaural DISPLAY on the Remote Commander.
mode, use a connecting cable (optional) for that
purpose.
2 Press STOP when you want to stop
playback.
3 Press m REW.
The tape stops automatically when the tape
counter reaches “0:00:00.”
4 Press PLAY.
The playback starts from the point
designated “0:00:00” on the tape counter.
40 Playback
b Notes • The Date search will not function correctly when
• There may be a discrepancy of several seconds there is a blank section between recorded sections on
between the time code and the tape counter. the tape.
• Zero set memory will not function correctly if there
is a blank section between recorded sections on the
tape. Searching for a still image
– Photo search
Searching for a scene by date of
recording – Date search
You can locate the still image you have
recorded on a tape.
You can locate the point where the recording
date changes.
SEARCH M.
./>
SEARCH M.
STOP
Playback
./>
STOP
,continued
Playback 41
Playing back still images in
sequence – Photo scan
SEARCH M.
./>
STOP
42 Playback
BAdvanced operations OTHERS (p. 59)
AUDIO MODE
REMAIN
FRAME REC
SEL/PUSH EXEC dial POWER switch 5 Turn the SEL/PUSH EXEC dial to
select the desired mode, then press the
dial.
1 Turn on the power (p. 15).
TAPE SET STBY
REC MODE
AUDIO MODE
REMAIN ON
2 Press MENU. FRAME REC
I N T. REC
RETURN
The menu screen appears.
[MENU] : END
PROGRAM AE
You can record pictures easily in a situation that requires various techniques by
selecting the following settings.
* Your camcorder is adjusted to focus only on subjects in the middle to far distance.
b Note
• When you set the NIGHTSHOT PLUS switch to ON, [PROGRAM AE] does not work.
(The indicator flashes.)
P EFFECT
For TRV128/228/328/428:
You can add special effects (such as films) to a picture before recording.
appears when each effect is selected.
For TRV260/265:
You can add special effects (such as films) to a picture before or after recording.
appears when each effect is selected.
b Note
• For TRV260/265:
You cannot add effects to externally input pictures. Also, you cannot output pictures edited
with Picture effects via the DV Interface.
,continued
AUTO SHTR
D ZOOM
You can select the maximum zoom level in case you want to zoom to a level
greater than 20 times while recording on a tape. Note that the image quality
decreases when you are using the digital zoom. This function is useful when
recording enlarged pictures of a distant subject, such as a bird.
,continued
* Picture appears in full screen when the wide-screen TV switches to full mode.
**Played in 4:3 mode. When you play a picture in the wide mode, it appears as you have seen
on the LCD screen or in the viewfinder.
GOFF Standard setting (to record pictures to play back on a 4:3 TV). The
recorded picture will not be wide.
CINEMA ( ) Select to record a picture to be played back in CINEMA mode.
16:9 FULL ( ) Select to record a picture to be played back on a 16:9 wide TV.
For TRV260/265:
You can record a 16:9 wide picture on the tape to watch on a 16:9 wide-screen TV
([16:9 WIDE] mode).
With this function [ON], your camcorder offers even wider angles when you
move the power zoom lever to the “W” side than recording in [OFF].
When you connect your camcorder to the S video input jack of a TV compatible
with the ID-1/ID-2 system and play the tape, the TV switches to full mode
automatically.
Refer also to the manuals supplied with your TV.
When viewed on the LCD screen
* Picture appears in full screen when the wide-screen TV switches to full mode.
**In 4:3 mode. When you play a picture in the wide mode, it appears as you have seen on the
LCD screen.
GOFF Standard setting (to record pictures to play back on a 4:3 TV). The
recorded picture will not be wide.
ON ( ) Select to record a picture to be played back on a 16:9 wide TV. The
recorded picture will be played in full mode when you connect to your
TV using an S (S1) video input jack compatible with ID-1/ID-2
systems.
z Tips
• The ID-1 system sends aspect ratio information (16:9, 4:3, or letter box) by inserting
signals between video signals.
• The ID-2 system sends a copyright protection signal with the ID-1 signals inserted between
video signals in an analog connection.
• S1 video sends information with the standard S video signal to select wide mode
automatically.
• The SteadyShot does not work. If you set [16:9 WIDE] to [ON] in the menu settings when
the SteadyShot is working flashes and the SteadyShot does not function.
,continued
b Note
• For TRV260/265:
Camera-shake cannot be completely compensated for in the following cases:
– When recording in a dark place
– When recording a subject with little contrast to the background
– When recording horizontal stripes
– When using the zoom
– When recording a fast moving subject
– When the zoom position is set to the W-end side
N.S. LIGHT
When using the NightShot plus function to record, you can record clearer pictures
by using the NightShot Light to emit infrared rays (invisible).
You can select the items listed below in the VCR SET
H i F i SOUND
menu (the PLAYER SET menu for AUDIO MIX
HiFi SOUND
For TRV260/265:
You can select how to play back audio recorded on a tape in stereo mode.
b Notes
• You can playback a dual sound track cassette on this camcorder. However, you cannot
record a dual sound track on this camcorder.
• The setting returns to [STEREO] when you disconnect the power source from your
camcorder for more than 5 minutes.
EDIT
For TRV128/228/328/428:
Picture degradation is minimized when you dub or edit a tape using the camcorder
as the playback device.
b Note
• The setting returns to [OFF] when you disconnect the power source from your camcorder
for more than 5 minutes.
,continued
DNR
For TRV128/228/328/428:
GON Select to eliminate color noise in the picture.
OFF Select to minimize picture artifacts in a picture containing lots of
movement.
AUDIO MIX
For TRV260/265:
You can adjust the audio balance between ST1 (the originally recorded sound)
and ST2.
b Notes
• You cannot adjust sound recorded in 16 bit audio mode.
• Only the originally recorded sound will be heard when you disconnect the power source
from your camcorder for more than 5 minutes.
LCD BRIGHT
See page 16 for details.
LCD B.L.
b Notes
• When you connect your camcorder to outside power sources, [BRIGHT] is automatically
selected for the setting.
• When you select [BRIGHT], battery life is reduced by about 10 percent during recording.
LCD COLOR
Turn the SEL/PUSH EXEC dial to adjust the color on the LCD screen. The
recorded picture will not be affected by this setting.
REC MODE
b Notes
• If you record in the LP mode, a mosaic-like noise may appear or sound may be interrupted
when you play back the tape on other camcorders or VCRs.
• For TRV128/228/328/428:
When you record a tape in the LP mode on your camcorder, recording is carried out in the
standard 8 mm system.
• For TRV260/265:
When you mix recordings in the SP mode and in the LP mode on one tape, the playback
picture may be distorted or the time code may not be written properly between the scenes.
AUDIO MODE
For TRV260/265:
G12BIT Select to record in the 12-bit mode (2 stereo sounds).
16BIT ( ) Select to record in the 16-bit mode (1 stereo sound with high quality).
ORC TO SET
For TRV128/228/328/428:
You can automatically adjust the recording condition to get the best possible
recording.
When you select [ORC TO SET] in the menu settings, [START/STOP KEY]
appears. Press REC START/STOP. [ORC] appears on the screen and adjustment
starts. Your camcorder returns to the standby mode when adjustment is complete.
It takes about 10 seconds for adjustment.
b Notes
• Each time you eject a cassette, this setting will be canceled.
REMAIN
FRAME REC
b Notes
• When you use frame recording continuously, the remaining tape time will not be indicated
correctly.
• The last scene will be longer than other scenes.
,continued
[b] [b]
a. [REC TIME]
b. [INTERVAL]
1 Turn the SEL/PUSH EXEC dial to select [SET], then press the dial.
2 Turn the SEL/PUSH EXEC dial to select [INTERVAL], then press the
dial.
3 Turn the SEL/PUSH EXEC dial to select the desired interval time
(30 seconds, 1, 5, 10 minutes), then press the dial.
4 Turn the SEL/PUSH EXEC dial to select [REC TIME], then press the
dial.
5 Turn the SEL/PUSH EXEC dial to select the desired recording time
(0.5, 1, 1.5, 2 seconds), then press the dial.
6 Turn the SEL/PUSH EXEC dial to select [ RETURN], then press the
dial.
7 Turn the SEL/PUSH EXEC dial to select [ON], then press the dial.
8 Press MENU to hide the menu settings.
flashes.
9 Press REC START/STOP.
The interval recording starts.
lights up during interval recording.
To cancel recording, set to [OFF] in the menu settings.
b Note
• There may be a discrepancy in recording time of up to ± 6 frames from the selected time.
z Tips
• If you adjust the focus manually, you may be able to record clear pictures even if the light
changes (p. 29).
• You can silence the beeps during recording (p. 59).
CLOCK SET
You can set the date and time (p. 17).
AUTO DATE
GON Select to record the date for 10 seconds after recording has started.
OFF Select to cancel the auto date function.
z Tip
• The auto date function automatically displays the date once a day. However, the date may
automatically appear more than once a day if:
– you set the date and time.
– you eject and insert the tape again.
– you stop recording within 10 seconds.
– you set [AUTO DATE] to [OFF] once and set it back to [ON] in the menu settings.
USB STREAM
For TRV260/265:
You can connect a USB cable (supplied) to your camcorder, and view the picture
displayed on the screen of your camcorder on your computer (USB Streaming).
For details, refer to the “Computer Applications Guide.”
GOFF Select to deactivate the USB Streaming function.
ON Select to activate the USB Streaming function.
LTR SIZE
,continued
DEMO MODE
When you remove a cassette from your camcorder, and select the CAMERA
mode, you can view the demonstration in about 10 minutes.
GON Select to see an overview of the functions available such as when you
are using this camcorder for the first time.
OFF Select when you do not intend to use the [DEMO MODE].
b Note
• You can view the demonstration only when the NIGHTSHOT PLUS switch is set to OFF.
z Tips
• The demonstration will be suspended in situations such as those described below.
– When a cassette is inserted.
– When a mode other than CAMERA is selected.
• If [A.SHUT OFF] is set to [5 min] when the camcorder is used on the battery pack, the
power will be turned off after approximately 5 minutes (p. 59).
DATA CODE
For TRV260/265:
GOFF Select not to display date, time and the camera settings data during
playback.
DATE/TIME Select to display the date and time during playback. (p. 37)
WORLD TIME
You can adjust the time difference when using your camcorder abroad. Set the
time difference by turning the SEL/PUSH EXEC dial, the clock will be adjusted
in accordance with the time difference. If you set the time difference to 0, the
clock returns to the originally set time.
BEEP
GMELODY Select to play a melody when you start/stop recording, operate your
camcorder with the SEL/PUSH EXEC dial, or when an unusual
condition occurs on your camcorder.
NORMAL Select to sound a beep instead of the melody.
OFF Select to cancel the melody, beep sound, shutter sound and operation
confirmation beep.
A.SHUT OFF
G5 min Select to activate the Auto shut off. When approximately 5 minutes
have elapsed while you do not operate your camcorder, the camcorder
is automatically turned off to prevent the battery from becoming
consumed.
NEVER Select to deactivate the Auto shut off.
,continued
COMMANDER
For TRV228/428/ TRV265:
GON Select when using the Remote Commander supplied with your
camcorder.
OFF Select to deactivate the Remote Commander to prevent your
camcorder from responding to a command sent by another VCR
remote control unit.
b Note
• The setting returns to [ON] when you have the power source disconnected from your
camcorder for more than 5 minutes.
DISPLAY
GLCD Select to show the displays such as the time code on the LCD screen
and in the viewfinder.
V-OUT/LCD Select to show the displays such as the time code on the TV screen,
LCD screen, and in the viewfinder.
REC LAMP
GON Select to turn on the camera recording lamp on the front of your
camcorder during recording.
OFF Select this setting in the following recording situations. The camera
recording lamp will not light up during recording.
• When you do not want the subject to be nervous about being
recorded.
• When you are recording close to the subject.
• When the subject reflects the recording lamp.
VIDEO EDIT
For TRV260/265:
You can select up to 20 scenes (programs) and record them in the desired order to
another recording device such as VCR (p. 69).
For TRV128/228/328/428:
Dubbing/Editing
Yellow
Black
A/V connecting cable (supplied)
VCRs
Signal flow
,continued
Dubbing/Editing 61
For TRV260/265:
A/V OUT jack
Connecting with an i.LINK cable
i.LINK jack
DV Interface
Yellow
White
A/V connecting cable (supplied)
VCRs
Red
Signal flow
* When there is an S video jack on the device to be To use an i.LINK cable for connection
connected, connect the S video plug to that jack For TRV260/265:
instead of using the yellow video plug. The audio
Use an i.LINK cable (optional) to connect your
will not be output when you connect with the S video
camcorder to other device via the DV Interface.
plug alone.
Pictures can be reproduced more faithfully with this The video and sound signals are transmitted
connection. digitally, producing high quality pictures. Note
that you cannot record the picture and sound
b Notes on the A/V connecting cable separately. For details, see page 84.
• Use the A/V connecting cable to connect your
camcorder to other devices. Before connecting,
make sure the [DISPLAY] setting in the
(OTHERS) menu is set to [LCD] (the default
setting) (p. 60).
• For TRV128/228/328/428:
When you are connecting your camcorder to stereo
device, connect the audio plug of the A/V
connecting cable to the left (white) jack on the VCR.
• For TRV260/265:
When you are connecting your camcorder to
monaural device, connect the yellow plug of the
A/V connecting cable to the video jack, and the red
or the white plug to the audio jack on the VCR.
62 Dubbing/Editing
• For TRV260/265:
Dubbing/Editing
PLAY/EDIT mode.
b Notes
• When dubbing using the A/V connecting cable,
press DSPL/BATT INFO to hide indicators such as
time code (p. 37). Otherwise, they will be recorded
on the tape.
• For TRV260/265:
When connected using the A/V connecting cable, to
record the date/time and camera settings data, have
it displayed on screen (p. 37).
Dubbing/Editing 63
Dubbing a tape easily 5 Turn the SEL/PUSH EXEC dial to
select [SETUP], then press the dial.
– Easy Dubbing
EASY DUBBING 0 :0 0 :0 0
SETUP
( TRV128/228/328/428) I R SETUP
PAUSE MODE
3
I R TEST
RETURN
the camcorder.
NORMAL
[ E A S Y D UB ] : E N D
64 Dubbing/Editing
[IR SETUP] code list
10Point the infrared ray emitter of your The following [IR SETUP] codes are recorded
camcorder towards the remote sensor on your camcorder by default. (It is set at “3” as
on your VCR, from about 30 cm (12 the default setting.)
in.) away, with no obstructions.
Manufacturing [IR SETUP] code
Remote sensor VCR company
Infrared ray
emitter Sony 1, 2, 3, 4, 5, 6
Admiral (M. Wards) 89
Aiwa 47, 54, 80
Akai 49, 51
Audio Dynamic 21, 35
Bell&Howell (M. Wards) 36
Broksonic 21, 70, 82
Dubbing/Editing
DBX 21, 33, 35
select [EXECUTE], then press the dial. Dimensia 8
Recording starts on your VCR when the Emerson 26, 48, 59, 70, 80, 81, 82
setting is correct. [COMPLETE] appears
when the [IR SETUP] code test is finished. Fisher 36, 37, 44, 45
Go on to the next step. Funai 80
When recording fails to start, select another General Electric 8, 32*, 77, 94*, 101
[IR SETUP] code and try again.
Goldstar/LG 47
GO VIDEO 71
14Turn the SEL/PUSH EXEC dial to
Hitachi 8, 42, 78
select [ RETURN], then press the
dial. HQ 40
Instant Replay 77, 78
JC Penny 8, 21, 33, 35, 36, 42, 77
JVC 12, 13, 14, 21, 33, 35
Kenwood 21, 33, 35, 47
LXI (Sears) 36, 37, 42, 44, 45, 47,
49, 80
Magnavox 17, 77, 78, 83
Marantz 21, 33, 35
Marta 47
Memorex 37, 77
Minolta 8, 42
Mitsubishi/MGA 22, 23, 24, 28, 29
,continued
Dubbing/Editing 65
Manufacturing [IR SETUP] code
Step 2: Selecting the title
company
Multitech 23, 32, 80
NEC 21, 33, 35
Olympic 77, 78 You can insert a title.
Optimus 22 You can select one of the 8 preset titles and
Orion 60 the 2 custom titles. See steps 1 to 4 on
page 31 to create original titles.
Panasonic 16, 17, 77, 78
Pentax 8, 42
Philco 26, 70, 77, 78
1 Turn the SEL/PUSH EXEC dial to
select [TITLE SEL], then press the
Philips 47, 77, 78, 83 dial.
Pioneer 78
EASY DUBBING 0 :0 0 :0 0
T I T LE SEL
Quasar 6, 16, 17, 77, 78 OFF
HE L LO !
RCA/PROSCAN 7, 8, 16, 40, 41, 42, 77, HA P P Y B I R T HDA Y
H A P P Y HO L I D A Y S
CONGR A T U L A T I ON S !
78, 78*, 83, 101 OU R SWE E T B A B Y
[EASY DUB]:END
Realistic 22, 36, 37, 77, 80, 88
Sansui 21
Singer 73 2 Turn the SEL/PUSH EXEC dial to
Samsung 24, 24*, 32, 32*, 41, 94, select the desired title, then press the
94* dial.
Sanyo 26, 36, 37, 47 The title flashes.
E A S Y D U B B I NG 0 :0 0 :0 0
Scott 22, 23, 24, 28, 32, 37, OK
COLOR
40, 41 S I ZE
BACK COL
HELLO!
Sharp 88, 89
Shintom 73 [EASY DUB]:END
66 Dubbing/Editing
4 Turn the SEL/PUSH EXEC dial to 2 Turn the SEL/PUSH EXEC dial to
select [OK], then press the dial. select [NORMAL] or [PREVIEW],
The title lights up. then press the dial.
EASY DUBBING
START
0 :0 0 :0 0 When you select [NORMAL]
T I T LE SEL ON
MODE SEL You can record into the VCR normally.
SETUP
Dubbing/Editing
• The background color changes as follows:
[FADE] y [WHITE] y [YELLOW] y
[VIOLET] y [RED] y [CYAN] y [GREEN] Step 4: Performing Easy Dubbing
y [BLUE] y [BLACK]
HELLO!
NORMAL
[EASY DUB]:END
,continued
Dubbing/Editing 67
2 Turn the SEL/PUSH EXEC dial to
Recording pictures
select [EXECUTE], then press the dial.
When dubbing ends, your camcorder and
VCR stop automatically.
from a VCR ( TRV260/265)
Then the display returns to the Easy
Dubbing initial screen. You can record and edit pictures from a VCR
on a tape inserted in your camcorder.
Insert a cassette for recording in your
To stop dubbing during editing camcorder.
Press (stop) on your camcorder.
b Note
• Your camcorder can only record from an NTSC
To quit Easy Dubbing source. For example, European video or TV
Press EASY DUB. programs (PAL/SECAM) cannot be recorded
correctly. See page 81 for details on TV color
b Note systems.
• [NOT READY] appears on the screen when
[START] is not carried out.
1 Connect your VCR to your camcorder
(p. 62).
Use an i.LINK cable (optional) for
connection.
z Tip
• appears when you connect your camcorder
and other devices via an i.LINK cable. (This
indicator may also appear on your TV.)
68 Dubbing/Editing
Dubbing selected 2 Prepare your VCR.
• Insert a cassette for recording.
scenes from a tape • Set the input selector to input mode, if
your VCR has one.
– Digital program editing
( TRV260/265) 3 Prepare your camcorder (playing
device).
You can select up to 20 scenes (programs)
• Insert a cassette for editing.
and record them in the desired order to other
• Slide the POWER switch repeatedly to
recording device such as VCR.
select the PLAY/EDIT mode.
Delete unwanted scene
4 Press MENU.
Dubbing/Editing
dial.
VIDEO EDIT 0:08:55:06
Step 1: Preparing your camcorder MARK
UNDO
1 IN
ERASE ALL
and VCR for operation START
EDIT SET
TOTAL 0:00:00:00
SCENE 0
[MENU] : END
”CUT–IN”
• You cannot perform the Digital program editing on ”CUT–OUT”
IR SETUP
a VCR that does not support [IR SETUP] codes. PAUSEMODE
IR TEST
• When your camcorder is connected to the VCR via RETURN
[MENU] : END
the DV Interface, you cannot record the title or
indicators.
[MENU] : END
,continued
Dubbing/Editing 69
5 Point the infrared ray emitter of your
9 Turn the SEL/PUSH EXEC dial to camcorder towards the remote sensor on
select [i.LINK] or [IR], then press the your VCR, from about 30 cm (12 in.)
dial. away, with no obstructions.
When connecting with an i.LINK 6 Insert a cassette into your VCR, and set
cable the VCR to recording pause.
After selecting [i.LINK], go on to “Step 2: 7 Turn the SEL/PUSH EXEC dial to select
Adjusting the synchronization of the VCR” [IR TEST], then press the dial.
(p. 70).
8 Turn the SEL/PUSH EXEC dial to select
When connecting with an A/V [EXECUTE], then press the dial.
connecting cable The recording starts on your VCR when the
After selecting [IR], follow the procedure setting is correct. [COMPLETE] appears
described in “To set the [IR SETUP] code” when the [IR SETUP] code test is finished.
(p. 70). Go on to “Step 2: Adjusting the
synchronization of the VCR” (p. 70).
When recording fails to start, select another
To set the [IR SETUP] code IR code and try again.
When you connect with an A/V connecting
cable, you need to check the [IR SETUP] code
signal to see if your VCR can be operated by Step 2: Adjusting the
your camcorder (infrared ray emitter). synchronization of the VCR
Remote sensor VCR
Infrared ray
emitter
Follow the steps below when you are
performing digital program editing for the
first time to a tape in a VCR. You can skip
this setting if you have set up your VCR
before using the following procedure.
You can adjust the synchronization of your
camcorder and the VCR to avoid not
1 Turn the SEL/PUSH EXEC dial to select recording the starting scene.
[IR SETUP], then press the dial.
2 Turn the SEL/PUSH EXEC dial to select
the [IR SETUP] code of your VCR, then
1 Remove the cassette from your
press the dial.
camcorder. Prepare a pen and paper
For the [IR SETUP] code of your VCR, to take notes.
refer to “[IR SETUP] code list” (p. 65).
When there is more than one code listed for
the manufacturer of your VCR, try each
2 Set the VCR to recording pause mode.
Skip this step if you have selected [i.LINK]
code and find the most appropriate one.
in step 9 on p. 70.
3 Turn the SEL/PUSH EXEC dial to select
[PAUSEMODE], then press the dial. b Note
• Run the tape for about 10 seconds before
4 Turn the SEL/PUSH EXEC dial to select
pausing. The starting scenes may not get
the mode to cancel recording pause on
recorded when you start recording from
the VCR, then press the dial.
the beginning of the tape.
Refer to the operating instructions supplied
with your VCR for details on operation.
70 Dubbing/Editing
3 Turn the SEL/PUSH EXEC dial to 8 Turn the SEL/PUSH EXEC dial to
select [ADJ TEST], then press the dial. select the average numerical value of
[IN], then press the dial.
VIDEO EDIT
EDIT SET
0:08:55:06 The calculated start position for recording
CONTROL
ADJ TEST RETURN is set.
”CUT–IN” EXECUTE
”CUT–OUT”
IR SETUP ENGAGE
PAUSEMODE REC PAUSE
IR TEST
RETURN
[MENU] : END
9 Turn the SEL/PUSH EXEC dial to
select [”CUT-OUT”], then press the
dial.
4 Turn the SEL/PUSH EXEC dial to VIDEO EDIT
EDIT SET
0:08:55:06
VIDEO EDIT
EDIT SET
0:08:55:06 10Turn the SEL/PUSH EXEC dial to
CONTROL
ADJ TEST COMPLETE
select the average numerical value of
”CUT–IN”
”CUT–OUT”
IR SETUP
[OUT], then press the dial.
PAUSEMODE
Dubbing/Editing
IR TEST The calculated stop position for recording is
RETURN
[MENU] : END set.
VIDEO EDIT
EDIT SET
0:08:55:06 1 Prepare a cassette.
CONTROL
ADJ TEST Insert a tape to be played back into the
”CUT–IN” 0
”CUT–OUT”
IR SETUP
camcorder.
PAUSEMODE
IR TEST
Insert a cassette for recording into your
RETURN
[MENU] : END VCR.
,continued
Dubbing/Editing 71
2 Press MENU. 8 Press the SEL/PUSH EXEC dial.
The ending point of the first program is set,
and the lower part of the program mark
3 Turn the SEL/PUSH EXEC dial to changes to light blue.
select (OTHERS), then press the
dial. VIDEO EDIT
MARK 2 IN
0:09:07:06
UNDO
ERASE ALL
START
EDIT SET
4 Turn the SEL/PUSH EXEC dial to TOTAL 0:00:12:00
SCENE 1
select [VIDEO EDIT], then press the [MENU] : END
dial.
VIDEO EDIT
MARK
UNDO
ERASE ALL
1 IN
0:08:55:06
9 Repeat steps 5 to 8 and create
START
EDIT SET
programs.
TOTAL 0:00:00:00
SCENE 0
[MENU] : END
10Set your VCR to the recording pause.
Skip this step if your camcorder is connected
via an i.LINK cable.
5 Search for the beginning of the first
scene that you want to record on your 11Turn the SEL/PUSH EXEC dial to
camcorder, then pause playback. select [START], then press the dial.
VIDEO EDIT 0:09:07:06
6 Turn the SEL/PUSH EXEC dial to MARK
UNDO
ERASE ALL
ENGAGE
REC PAUSE
VIDEO EDIT
MARK
UNDO
ERASE ALL
0:08:55:06
1 OUT
12Turn the SEL/PUSH EXEC dial to
START
EDIT SET
select [EXECUTE], then press the dial.
TOTAL 0:00:00:00 A search for the beginning of the first
SCENE 0
[MENU] : END
program starts, then the recording starts.
[SEARCH] appears during search and
[EDITING] appears during editing.
72 Dubbing/Editing
To end Digital program editing
Press MENU.
To erase programs
1 Follow steps 1 to 4 in “Recording the
selected scenes as programs” (p. 71).
2 Turn the SEL/PUSH EXEC dial to select
[UNDO] or [ERASE ALL], then press
the dial.
When you select [UNDO]
You can erase the last set program.
When you select [ERASE ALL]
You can erase all the programs.
3 Turn the SEL/PUSH EXEC dial to select
[EXECUTE], then press the dial.
Dubbing/Editing
The programs are deleted. To cancel this
operation, select [RETURN], and then
press the dial.
b Notes
• You cannot set starting point or ending point on a
blank section of the tape. If there is a blank section,
the total time may not appear correctly.
• When you cannot operate the device correctly using
an i.LINK cable connection, select [IR] in step 9 on
p. 70, and set the [IR SETUP] code.
Dubbing/Editing 73
Troubleshooting persists, remove the power source and
contact your Sony dealer.
Troubleshooting If “C:ss:ss” is displayed on the LCD
screen or the viewfinder, the self-diagnosis
display function is activated. See page 79 for
If you run into any problem using your details.
camcorder, use the following table to
troubleshoot the problem. If the problem
Overall operations
Batteries/Power sources
74 Troubleshooting
Symptom Cause and/or Corrective Actions
The remaining battery time indicator • The temperature of the environment is too high or too low, or the battery
does not indicate the correct time. pack has not been charged enough. This is not a malfunction.
cFully charge the battery again. If the problem persists, replace the
battery pack with a new one. It may be damaged. (p. 12, 83)
The power turns off frequently • A problem has occurred in the remaining battery time indicator, or the
although the remaining battery battery pack has not been charged enough.
indicator indicates that the battery cFully charge the battery again to correct the indication. (p. 12)
pack has enough power to operate.
The power abruptly turns off. • [A.SHUT OFF] in the (OTHERS) menu is set to [5 min]. (p. 59)
cWhen approximately 5 minutes have elapsed while you do not operate
your camcorder, the camcorder is automatically turned off. Slide the
POWER switch down to turn the power on again. (p. 15) Or use the AC
adaptor.
A problem occurs when the cTurn off the power, and disconnect the AC Adaptor from the wall outlet.
camcorder is connected to the AC Then, connect it again.
Adaptor.
Cassette tapes
Troubleshooting
Cassette cannot be ejected from the cMake sure the power source (battery pack or AC Adaptor) is connected
compartment. correctly. (p. 12)
cRemove the battery pack from the camcorder, then attach it again. (p. 12)
cAttach a charged battery pack to the camcorder. (p. 12)
Cassette is not ejected even when the cMoisture condensation is starting in your camcorder. (p. 86)
cassette lid is open.
The remaining tape indicator is not cSet [ REMAIN] to [ON] in the (TAPE SET) menu to always
displayed. display the remaining tape indicator. (p. 55)
LCD screen/viewfinder
Troubleshooting 75
Symptom Cause and/or Corrective Actions
The picture in the viewfinder is not cUse the viewfinder lens adjustment lever to adjust the lens. (p. 16)
clear.
The picture in the viewfinder has cClose the LCD panel. The picture is not displayed in the viewfinder
disappeared. when the LCD panel is open. (p. 16)
Recording
76 Troubleshooting
Symptom Cause and/or Corrective Actions
Flickering or changes in color occurs. cThis occurs when recording pictures under a fluorescent lamp, sodium
lamp, or mercury lamp in the soft portrait or sports lesson mode. Cancel
[PROGRAM AE] in this case. (p. 44)
END SEARCH does not work. • The cassette was ejected after recording.
• The cassette is new and has nothing recorded.
END SEARCH does not work • There is a blank section in the beginning or middle of the tape. This is
correctly. not a malfunction.
The built-in light does not function. cPress LIGHT repeatedly to select .
cIf the problem presists, contact your Sony dealer or local authorized
Sony service facility.
Playback
Troubleshooting
cFor TRV128/228/328/428:
Set [EDIT] to [OFF] in the (PLAYER SET) menu. (p. 51)
No sound or only a low sound is cFor TRV260/265:
heard. Set [HiFi SOUND] to [STEREO] in the (VCR SET) menu. (p. 51)
cTurn up the volume. (p. 34)
cFor TRV260/265:
In the (VCR SET) menu, adjust [AUDIO MIX] from the [ST2] side
until the sound is heard appropriately. (p. 52)
cWhen you are using an S VIDEO plug, make sure the black plug for
TRV128/228/328/428, or the red and white plugs for TRV260/
265 of the A/V connecting cable are connected as well. (p. 39)
The sound breaks off. cClean the head using the cleaning cassette (optional). (p. 86)
For TRV265: • There is a blank section in the beginning or middle of the tape. This is
Cannot perform the Date search with not a malfunction.
the recording date displayed on the
screen.
For TRV260/265: • The tape you are playing was recorded without setting the date and time.
“---” is displayed on the screen. • A blank section on the tape is being played.
• The data code on a tape with a scratch or noise cannot be read.
END SEARCH does not work. • The cassette was ejected after recording.
• The cassette is new and has nothing recorded.
END SEARCH does not work • There is a blank section in the beginning or middle of the tape. This is
correctly. not a malfunction.
,continued
Troubleshooting 77
Symptom Cause and/or Corrective Actions
For TRV260/265: • The tape is recorded in the Hi8 /standard 8 mm system.
The picture does not appear on the
screen when playing back a tape.
Noises appear on the screen. • The tape was recorded in a TV color system other than that of your
camcorder. (p. 81)
Dubbing/Editing
78 Troubleshooting
Warning indicators
and messages
Self-diagnosis display/Warning indicators
If indicators appear on the screen, check the following. See the page in parentheses for details.
Indication Cause and/or Corrective Actions
C:ss : ss/E:ss : ss (Self- Some symptoms can be fixed by yourself. If the problem persists even after
diagnosis display) you tried a couple of times, contact your Sony dealer or local authorized
Sony service facility.
C:04:ss
cA battery pack that is not an “InfoLITHIUM” battery pack is being used.
Use an “InfoLITHIUM” battery pack. (p. 83)
C:21:ss
cMoisture condensation has occurred. Remove the cassette and leave your
camcorder for at least 1 hour, then re-insert the cassette. (p. 86)
C:22:ss
cClean the head using a cleaning cassette (optional). (p. 86)
C:31ss / C:32ss
cSymptoms that are not described above have occurred. Remove and
Troubleshooting
insert the cassette, then operate your camcorder again. Do not perform
this procedure if moisture starts to condense. (p. 85)
cRemove the power source. Reconnect it again and operate your
camcorder again.
cChange the tape.
cPress the RESET button and operate your camcorder again.
E:61:ss / E:62:ss
cContact your Sony dealer or local authorized Sony service facility.
Inform them of the 5-digit code, which starts from “E.”
E (Battery level warning) • The battery pack is nearly used up.
• Depending on the operating, environmental, or battery conditions, the
E indicator may flash, even if there are approximately 5 to 10 minutes
remaining.
% (Moisture condensation warning)* cEject the cassette, set the POWER switch to (CHG) OFF, and leave it for
about 1 hour with the cassette lid open. (p. 86)
Q (Warning indicator pertaining to Slow flashing:
the tape) • There is less than 5 minutes remaining on the tape.
• No cassette is inserted.*
• The write-protect tab on the cassette is set to lock. (p. 82)*
Fast flashing:
• The tape has run out.*
,continued
Troubleshooting 79
Indication Cause and/or Corrective Actions
Z (Eject cassette warning)* Slow flashing:
• The write-protect tab on the cassette is set to lock. (p. 82)
Fast flashing:
• Moisture condensation has occurred. (p. 86)
• The tape has run out.
• The self-diagnosis display code is displayed. (p. 79)
* You hear a melody or beep sound when the warning indicators appear on the screen.
Warning messages
The following messages will appear to prompt you to correct the situation.
Subjects Indications Corrective Actions/References
Battery Use the “InfoLITHIUM” battery pack. cSee page 83.
Battery level is low. cCharge the battery. (p. 12)
Old battery. Use a new one. cSee page 83
Z Re-attach the power source. –
Moisture % Z Moisture condensation. Eject the cassette cSee page 86.
condensation
% Moisture condensation. Turn off for 1H. cSee page 86.
Cassette/tape Q Insert a cassette. cSee page 18.
Z Reinsert the cassette. cThe cassette might be damaged, etc.
Q Z The tape is locked - check the tab. cSee page 82.
Q The tape has reached the end. –
Others Cannot record due to copyright protection. –
Dirty video head. Use a cleaning cassette. cSee page 86.
Cannot start Easy Handycam cSee page 26 and 36.
Cannot cancel Easy Handycam cSee page 26 and 36.
Cannot start Easy Handycam with USB connected –
Invalid button with Easy Handycam operation cSee page 26 and 36.
USB invalid during Easy Handycam cPress SEL/PUSH EXEC dial.
80 Troubleshooting
Additional Information Simple setting of clock by time
difference
Using your camcorder You can easily set the clock to the local time by
setting a time difference when using your
abroad camcorder abroad. Select [WORLD TIME] in
the (OTHERS) menu, then set the time
difference (p. 59).
Power supply
You can use your camcorder in any country/
regions using the AC Adaptor supplied with
your camcorder within AC 100 V to 240 V,
50/60 Hz.
Use a commercially available AC plug
adaptor [a], if necessary, depending on the
design of the wall outlet [b].
On TV color systems
Your camcorder is an NTSC system-based
camcorder. If you want to view the playback
picture on a TV, it must be an NTSC system-
based TV (see following list) with the AUDIO/
VIDEO input jack.
System Used in
Additional Information
NTSC Bahama Islands, Bolivia, Canada,
Central America, Chile, Colombia,
Ecuador, Guyana, Jamaica, Japan,
Korea, Mexico, Peru, Surinam,
Taiwan, the Philippines, the
U.S.A., Venezuela, etc.
PAL Australia, Austria, Belgium,
China, Czech Republic, Denmark,
Finland, Germany, Holland, Hong
Kong, Hungary, Italy, Kuwait,
Malaysia, New Zealand, Norway,
Poland, Portugal, Singapore,
Slovak Republic, Spain, Sweden,
Switzerland, Thailand, United
Kingdom, etc.
PAL - M Brazil
PAL - N Argentina, Paraguay, Uruguay
SECAM Bulgaria, France, Guiana, Iran,
Iraq, Monaco, Russia, Ukraine, etc.
Additional Information 81
For TRV260/265:
Usable cassette When you record
You cannot record software on your
tapes camcorder that contains copyright
control signals for copyright protection
You can use standard 8 mm and Hi8 , of software.
Digital8 video cassettes on your camcorder. [Cannot record due to copyright protection.]
appears on the LCD screen, or on the TV screen
Hi8 system if you try to record such software.
This Hi8 system is an extension of the Your camcorder does not record copyright
standard 8 mm system, and was developed to control signals on the tape when it records.
produce higher quality pictures.
You cannot play back a tape recorded in the
Notes on use
Hi8 system correctly on video recorders/ To prevent accidental erasure
players other than a Hi8 video recorder/player. Slide the write-protect tab on the cassette to set
to SAVE.
Digital8 system
This video system has been developed to enable
digital recording to Hi8 /Digital8 video
cassette.
The recording time when you use your
Digital8 system camcorder on Hi8 /
standard 8 mm tape is half the recording time
when using the conventional Hi8 /standard
8 mm system camcorder. (120 minutes of
recording time becomes 60 minutes in the SP REC: The cassette can be recorded.
mode.) SAVE: The cassette cannot be recorded (write-
protected).
To prevent a blank section from being
made on the tape When labeling the cassette
Press END SEARCH to go to the end of the
Be sure to place the label only on the locations
recorded section before you begin the next
as shown in the following illustration so as not
recording in the following cases:
to cause malfunction of your camcorder.
– You have ejected the cassette during
recording. Do not put a
label along the
– You have played back the tape. border.
If there is a blank section or discontinuous
signals on your tape, re-record from the
beginning to the end of the tape as described
above.
Labeling position
Copyright signal
After using the cassette
When you play back
Rewind the tape to the beginning to avoid
If the cassette you play back on your camcorder
distortion of the picture or the sound. The
contains copyright signals, you cannot copy it to
cassette should then be put in its case, and stored
a tape in another video camera connected to
in an upright position.
your camcorder.
, , , and are
trademarks.
82 Additional Information
– Put the battery pack in a pocket to warm it
About the up, and insert it in your camcorder right
before you start taking shots.
“InfoLITHIUM” – Use a large capacity battery pack: NP-
QM71/QM71D/QM91/QM91D (optional).
battery pack • Frequent use of the LCD screen or a frequent
playback, fast forward or rewind operation
wears out the battery pack faster. We
This unit is compatible with the
recommend using a large capacity battery
“InfoLITHIUM” battery pack (M series). Your
pack: NP-QM71/QM71D/QM91/QM91D
camcorder operates only with the
(optional).
“InfoLITHIUM” battery pack.
• Be sure to set the POWER switch to (CHG)
“InfoLITHIUM” M series battery packs have
OFF when not recording or playing back on
the mark.
your camcorder. The battery pack is also
What is the “InfoLITHIUM” battery consumed when your camcorder is in
recording standby or playback pause.
pack?
• Have spare battery packs ready for two or
The “InfoLITHIUM” battery pack is a lithium-
three times the expected recording time, and
ion battery pack that has functions for
make trial recordings before making the actual
communicating information related to operating
recording.
conditions between your camcorder and an
• Do not expose the battery pack to water. The
optional AC Adaptor/charger.
battery pack is not water resistant.
The “InfoLITHIUM” battery pack calculates
the power consumption according to the About remaining battery time indicator
operating conditions of your camcorder, and • When the power goes off even though the
displays the remaining battery time in minutes. remaining battery time indicator indicates that
With an AC Adaptor/charger (optional), the the battery pack has enough power to operate,
remaining battery time and charging time charge the battery pack fully again. The
appear.
Additional Information
indication on the remaining battery time will
be indicated correctly. Note, however, that the
To charge the battery pack
battery indication will not be restored if it is
• Be sure to charge the battery pack before you
used in high temperatures for a long time, or if
start using your camcorder.
left in a fully charged state, or when the
• We recommend charging the battery pack in
battery pack is frequently used.
an ambient temperature of between 10°C to
Use the remaining battery time indication as a
30°C (50°F to 86°F) until the CHG (charge)
guide to the approximate shooting time.
lamp turns off. If you charge the battery pack
• The E mark that indicates low battery flashes
outside of this temperature range, you may not
even if there are still 5 to 10 minutes of battery
be able to charge it efficiently.
time remaining, depending on the operating
• After charging is complete, either disconnect
conditions or ambient temperature and
the cable from the DC IN jack on your
environment.
camcorder or remove the battery pack.
About storage of the battery pack
To use the battery pack effectively
• If the battery pack is not used for a long time,
• Battery pack performance decreases when the
fully charge the battery pack and use it on your
surrounding temperature is 10°C (50°F) or
camcorder once a year to maintain the proper
below, and the length of time you can use the
function.
battery pack becomes shorter. In that case, do
To store the battery pack, remove it from your
one of the following to use the battery pack for
camcorder and put it in a dry, cool place.
a longer time.
• To completely use up the battery pack on your
camcorder, leave your camcorder in tape
,continued
Additional Information 83
recording standby until the power goes off
without a cassette inserted.
About i.LINK
About battery life
• The battery life is limited. Battery capacity The DV Interface on this unit is an i.LINK-
drops little by little as you use it more and compliant DV Interface. This section describes
more, and as time passes. When the available the i.LINK standard and its features.
battery time is shortened considerably, a
probable cause is that the battery pack has What is i.LINK?
reached the end of its life. Please buy a new i.LINK is a digital serial interface for
battery pack. transferring digital video, digital audio, and
• The battery life varies depending on how it is other data to other i.LINK-compatible device.
stored and the operating conditions and You can also control other device using the
environment for each battery pack. i.LINK.
i.LINK-compatible device can be connected
using an i.LINK cable. Possible applications are
“InfoLITHIUM” is a trademark of Sony
operations and data transactions with various
Corporation.
digital AV devices.
When two or more i.LINK-compatible device
are connected to this unit in a daisy chain,
operations and data transactions are possible
with not only the device that this unit is
connected to but also with other devices via the
directly connected device.
Note, however, that the method of operation
sometimes varies according to the
characteristics and specifications of the device
to be connected. Also, operations and data
transactions may not be possible on some
connected device.
b Note
• Normally, only one device can be connected to this
unit with the i.LINK cable. When connecting this
unit to i.LINK-compatible device having two or
more DV Interfaces, refer to the operating
instructions of the device to be connected.
z Tips
• i.LINK is a more familiar term for the IEEE 1394
data transport bus proposed by Sony, and is a
trademark approved by many corporations.
• IEEE 1394 is an international standard standardized
by the Institute of Electrical and Electronics
Engineers.
84 Additional Information
device. It is also indicated near the i.LINK
interface on some device.
The maximum baud rate for device that does not
Maintenance and
have any indication (such as this unit) is
“S100.”
precautions
The baud rate may differ from the indicated
value when the unit is connected to device with On use and care
a different maximum baud rate. • Do not use or store the camcorder and
accessories in the following locations.
* What is Mbps? – Anywhere extremely hot or cold. Never
Mbps stands for “megabits per second,” or the leave them exposed to temperatures above
amount of data that can be sent or received in one 60°C (140°F), such as under direct sunlight,
second. For example, a baud rate of 100 Mbps means near heaters or in a car parked in the sun.
that 100 megabits of data can be sent in one second. They may malfunction or become
deformed.
To use i.LINK functions on this unit – Near strong magnetic fields or mechanical
For details on how to dub when this unit is vibration. The camcorder may malfunction.
connected to other video device having a DV – Near strong radio waves or radiation. The
Interface, see page 62, 63. camcorder may not be able to record
This unit can also be connected to other i.LINK properly.
(DV Interface) compatible device made by – Near AM receivers and video equipment.
Sony (e.g. a VAIO series personal computer) as Noise may occur.
well as to video device. – Sandy beach or anywhere dusty. If sand or
Before connecting this unit to your computer, dust gets in your camcorder, it may
make sure that application software supported malfunction. Sometimes this malfunction
by this unit is already installed on your cannot be repaired.
computer. – Near windows or outdoors, where the LCD
Some i.LINK compatible video device such as screen, the viewfinder, or the lens may be
Digital Televisions, DVD recorders/players,
Additional Information
exposed to direct sunlight. This damages
and MICROMV recorders/players are not the inside of the viewfinder or the LCD
compatible with DV device. Before connecting screen.
to other device, be sure to confirm whether the – Anywhere very humid.
device is compatible with DV device or not. • Operate your camcorder on DC 7.2 V (battery
For details on precautions and compatible pack) or DC 8.4 V (AC Adaptor).
application software, refer also to the operating • For DC or AC operation, use the accessories
instructions for the device to be connected. recommended in these operating instructions.
• Do not let your camcorder get wet, for
About the required i.LINK cable example, from rain or sea water. If your
Use the Sony i.LINK 4-pin-to-4-pin cable camcorder gets wet, it may malfunction.
(during DV dubbing). Sometimes this malfunction cannot be
repaired.
i.LINK and are trademarks of Sony • If any solid object or liquid get inside the
Corporation. casing, unplug your camcorder and have it
checked by a Sony dealer before operating it
any further.
• Avoid rough handling, disassembling,
modifying, or mechanical shock. Be
particularly careful of the lens.
• Keep the POWER switch setting to (CHG)
OFF when you are not using your camcorder.
,continued
Additional Information 85
• Do not wrap your camcorder with a towel, for Notes on moisture condensation
example, and operate it. Doing so might cause Moisture may condense when you bring your
heat to build up inside. camcorder from a cold place into a warm place
• When disconnecting the power code, pull by (or vice versa) or when you use your camcorder
the plug and not the code. in a humid place as shown below.
• Do not damage the power code such as by • When you bring your camcorder from a ski
placing anything heavy on it. slope into a place warmed up by a heating
• Keep metal contacts clean. device.
• Keep the Remote Commander and button- • When you bring your camcorder from an air-
type battery out of children’s reach. If the conditioned car or room into a hot place
battery is accidentally swallowed, consult a outside.
doctor immediately. • When you use your camcorder after a squall or
• If the battery electrolytic liquid has leaked, a shower.
– consult your local authorized Sony service • When you use your camcorder in a hot and
facility. humid place.
– wash off any liquid that may have contacted
your skin. How to prevent moisture condensation
– if any liquid gets in your eyes, wash with When you bring your camcorder from a cold
plenty of water and consult a doctor. place into a warm place, put your camcorder in
a plastic bag and seal it tightly. Remove the bag
When not using your camcorder for a
when the air temperature inside the plastic bag
long time
has reached the surrounding temperature (after
Occasionally turn it on and let it run such as by
about one hour).
playing back tapes for about 3 minutes.
Otherwise, unplug it from the wall outlet. Video head
Moisture condensation • When the video head becomes dirty, you
If your camcorder is brought directly from a cannot record pictures normally, or distorted
cold place to a warm place, moisture may picture or sound is played back.
condense inside your camcorder, on the surface • The video head suffers from wear after long
of the tape, or on the lens. In this state, the tape use. If you cannot obtain a clear image even
may stick to the head drum and be damaged or after using a cleaning cassette, it might be
your camcorder may not operate correctly. If because the video head is worn. Please contact
there is moisture inside your camcorder, your Sony dealer or local authorized Sony
[%Z Moisture condensation. Eject the cassette] service facility to have the video head
or [% Moisture condensation. Turn off for 1H.] replaced.
appears. The indicator will not appear when the • For TRV128/228/328/428:
moisture condenses on the lens. If the following problem occurs, clean the
video heads for 10 seconds with the Sony
If moisture condensation has occurred V8-25CLD cleaning cassette (optional).
None of the functions except cassette ejection – Playback pictures contains noise or the
will work. Eject the cassette, turn off your screen is displayed in blue.
camcorder, and leave it for about one hour with – Playback pictures are hardly visible.
the cassette lid open. Your camcorder can be
used again if the % or Z does not appear when
the power is turned on again.
If moisture starts to condense, your camcorder
sometimes cannot detect condensation. If this – Playback pictures do not appear.
happens, the cassette is sometimes not ejected – [ Dirty video head. Use a cleaning
for 10 seconds after the cassette lid is opened. cassette.] appears on the screen during
This is not a malfunction. Do not close the recording.
cassette lid until the cassette is ejected.
86 Additional Information
• For TRV260/265: – Leaving the casing in contact with rubber or
If the following problem occurs, clean the vinyl objects for a long period of time.
video heads for 10 seconds with the Sony
V8-25CLD cleaning cassette (optional). About care and storage of the lens
– Mosaic-pattern noise appears on the • Wipe the surface of the lens clean with a soft
playback picture or the screen is displayed cloth in the following instances:
in blue. – When there are fingerprints on the lens
surface.
– In hot or humid locations
– When the lens is exposed to salty air such as
at the seaside.
• Store in a well-ventilated location subject to
– Playback pictures do not move.
little dirt or dust.
– Playback pictures do not appear or the
• To prevent molds periodically clean the lens
sound breaks off.
as described above.
– [ Dirty video head. Use a cleaning
It is recommended you operate your camcorder
cassette.] appears on the screen during
about once a month to keep it in an optimum
recording.
state for a long time.
LCD screen
To charge the pre-installed button-type
• Do not add excessive pressure on the LCD
screen, as it may cause damage. battery
• If your camcorder is used in a cold place, a Your camcorder has a pre-installed button-type
residual image may appear on the LCD screen. battery to retain the date, time, and other
This is not a malfunction. settings even when the POWER switch is set to
• While using your camcorder, the back of the (CHG) OFF. The pre-installed button-type
LCD screen may heat up. This is not a battery is always charged while you are using
malfunction. your camcorder but it will get discharged
gradually if you do not use your camcorder. The
Additional Information
To clean the LCD screen button-type battery will be fully discharged in
• If fingerprints or dust make the LCD screen about 3 months if you do not use your
dirty, it is recommended you using the camcorder at all. However, even if the pre-
cleaning cloth (supplied) to clean it. When you installed button-type battery is not charged, the
use the LCD Cleaning Kit (optional), do not camcorder operation will not be affected as long
apply the cleaning liquid directly to the LCD as you are not recording the date.
screen. Use cleaning paper moistened with the
liquid. Procedures
Connect your camcorder to a wall outlet using
On handling the casing the supplied AC Adaptor, and leave it with the
• If the casing is soiled, clean the camcorder POWER switch set to (CHG) OFF for more
body with a soft cloth lightly moistened with than 24 hours.
water, and then wipe the casing with a dry soft
cloth.
• Avoid the following to avoid damage to the
finish.
– Using chemicals such as thinner, benzine,
alcohol, chemical cloths, repellent and
insecticide.
– Handling with above substances on your
hands.
Additional Information 87
For TRV260/265:
Specification 3.0 mm (1/6 type) CCD (Charge Coupled
Device)
Gross: Approx. 460 000 pixels
Effective: Approx. 290 000 pixels
Video camera recorder Lens
Combined power zoom lens
Filter diameter: 37 mm (1 1/2 in.)
20 × (Optical), 990 × (Digital)
F=1.6 - 2.4
System Focal length
Video recording system
2.5 - 50 mm (1/8 - 2 in.)
For TRV128/228/328/428:
When converted to a 35 mm still camera
2 rotary heads, Helical scanning FM system
42 - 840 mm (1 11/16 - 33 1/8 in.)
For TRV260/265:
Color temperature
2 rotary heads, Helical scanning system
Auto
Audio recording system
Minimum illumination
For TRV128/228/328/428:
For TRV128/228/328/428:
Rotary heads, FM system
1 lx (lux) (F 1.6)
For TRV260/265:
For TRV260/265:
Rotary heads, PCM system
4 lx (lux) (F 1.6)
Quantization: 12 bits (Fs 32 kHz, stereo 1,
0 lx (lux) (in the NightShot plus mode)*
stereo 2), 16 bits (Fs 48 kHz, stereo) * Objects unable to be seen due to the dark can be
Video signal shot with infrared lighting.
NTSC color, EIA standards
Usable cassette Input/Output connectors
8 mm video format cassette S video output
Tape speed 4-pin mini DIN
For TRV128/228/328/428: Luminance signal: 1 Vp-p, 75 Ω (ohms),
SP: Approx. 14.35 mm/s unbalanced
LP: Approx. 7.19 mm/s Chrominance signal: 0.286 Vp-p, 75 Ω
For TRV260/265: (ohms), unbalanced
SP: Approx. 28.67 mm/s Audio/Video output
LP: Approx. 19.11 mm/s AV MINIJACK
Recording/playback time (using 120 min. Hi8/ Video signal: 1 Vp-p, 75 Ω (ohms),
Digital8 video cassette) unbalanced, sync negative
For TRV128/228/328/428: Audio signal: 327 mV (at output impedance
SP: 2 h more than 47 kΩ (kilohms)), Output
LP: 4 h impedance with less than 2.2 kΩ (kilohms)
For TRV260/265: For TRV128/228/328/428:
SP: 1 h Monaural minijack (ø 3.5 mm)
LP: 1 h 30 min For TRV260/265:
Fast forward/rewind time (using 120 min. Hi8/ Stereo minijack (ø 3.5 mm)
Digital8 video cassette) RFU DC OUT
Approx. 5 min For TRV128/228/328/428:
Viewfinder Mini-minijack (ø 2.5 mm), DC5V
Electric viewfinder (monochrome) DV input/output
Image device For TRV260/265:
For TRV128/228/328/428: 4-pin connector
3.0 mm (1/6 type) CCD (Charge Coupled USB jack
Device) For TRV260/265:
Gross: Approx. 320 000 pixels mini-B
Effective: Approx. 200 000 pixels
88 Additional Information
LCD screen AC Adaptor AC-L15A/L15B
Picture Power requirements
6.2 cm (2.5 type) AC 100 - 240 V, 50/60 Hz
Total dot number Current consumption
123 200 (560 × 220) 0.35 - 0.18 A
Power consumption
General 18 W
Power requirements Output voltage
DC 7.2 V (battery pack) DC 8.4 V, 1.5 A
DC 8.4 V (AC Adaptor) Operating temperature
Average power consumption (when using the 0°C to 40°C (32°F to 104°F)
battery pack) Storage temperature
For TRV128/228/328/428: -20°C to + 60°C (-4°F to + 140°F)
During camera recording using the viewfinder Dimensions (approx.)
1.8 W 56 × 31 × 100 mm (2 1/4 × 1 1/4 × 4 in.) (w/h/
During camera recording using the LCD d) excluding the projecting parts
2.7 W Mass (approx.)
For TRV260/265: 190 g (6.7 oz) excluding the power cord
During camera recording using viewfinder
2.5 W Rechargeable battery pack (NP-FM30)
During camera recording using LCD Maximum output voltage
3.4 W DC 8.4 V
Operating temperature Output voltage
0°C to 40°C (32°F to 104°F) DC 7.2 V
Storage temperature Capacity
-20°C to + 60°C (-4°F to + 140°F) 5.0 Wh (700 mAh)
Dimensions (approx.) Dimensions (approx.)
85 × 98 × 151 mm (3 3/8 × 3 7/8 × 6 in.) (w/h/ 38.2 × 20.5 × 55.6 mm
d) (1 9/16 × 13/16 × 2 1/4 in.) (w/h/d)
Additional Information
Mass (Approx.) Mass (approx.)
780 g (1 lb 11 oz) main unit only 65 g (2.3 oz)
890 g (1 lb 15 oz) including the NP-FM30 Operating temperature
rechargeable battery pack, Hi8/Digital8 0°C to 40°C (32°F to 104°F)
cassette, lens cap, and shoulder strap Type
Supplied accessories Lithium ion
See page 11.
Design and specifications are subject to change
without notice.
,continued
Additional Information 89
Types of differences
z Provided
— Not provided
90 Additional Information
Quick Reference
Camcorder
Quick Reference
A Lens cap (p. 21, 25) To attach the lens cap
B LCD screen (p. 3, 16)
C OPEN button (p. 16)
D VOLUME –/+* button (p. 34)
E END SEARCH button (p. 33)
F Speaker
G Viewfinder (p. 3, 16)
H Battery pack
I LIGHT button (p. 23)
J FADER button (p. 30)
K BACK LIGHT button (p. 27)
L FOCUS button (p. 29)
M SEL/PUSH EXEC dial (p. 43)
* This button has a tactile dot.
,continued
Quick Reference 91
A Built-in light (p. 23) E Microphone
B Lens F NIGHTSHOT PLUS switch (p. 28)
C Infrared ray emitter (p. 64, 70)/ G EASY button (p. 26, 36)
For TRV228/428/ TRV265: H DSPL/BATT INFO button (p. 13, 37)
Remote sensor
D Camera recording lamp (p. 21, 26)
92 Quick Reference
A RESET button (p. 74) H CAMERA mode lamps (p. 15)
B For TRV260/265: I PLAY/EDIT mode lamp (p. 15)
BURN DVD/VCD J For TRV260/265:
You can easily take a picture recorded on Rec buttons (p. 68)
the tape and burn it onto a DVD or CD-R. REC (rec)
See the supplied “Computer Applications
Guide” for details. K For TRV128/228/328/428:
Quick Reference
For TRV128/228/328/428: COUNTER RESET button (p. 22)
EASY DUB (Easy Dubbing) button L For TRV128/228/328/428:
(p. 64) TIME button (p. 18, 25)
C TITLE button (p. 31) M For TRV128/228/328/428:
D EXPOSURE button (p. 28) DATE button (p. 18, 25)
* This button has a tactile dot.
E MENU button* (p. 43)
F Video control buttons (p. 34)
STOP (stop)
REW (rewind)
PLAY (playback)*
FF (fast-forward)
PAUSE (pause)
G CHG (charge) lamp (p. 12)
,continued
Quick Reference 93
A Viewfinder lens adjustment lever (p. 16) E Tripod receptacle
B Eyecup Make sure that the length of the tripod
screw is less than 5.5 mm (7/32 inch).
C Cassette lid Otherwise, you cannot attach the tripod
D OPEN/EJECT lever (p. 18) securely, and the screw may damage your
camcorder.
94 Quick Reference
Remote Commander
Insulation sheet
Quick Reference
A Transmitter
After turning on your camcorder, point 3 Place a new button-type lithium battery
towards the remote sensor to control your with the + side facing up.
camcorder.
B REC START/STOP button (p. 21)
C Power zoom button (p. 23)
D Video control buttons (Rewind, Playback,
Fast-forward, Pause, Stop, Slow) (p. 34)
E DISPLAY button (p. 37, 40)
F PHOTO button (p. 25)
4 Insert the battery case back into the
G SEARCH M. button (p. 41, 42) Remote Commander until it clicks.
H ./> buttons (p. 41, 42)
I ZERO SET MEMORY button (p. 40)
,continued
Quick Reference 95
WARNING
Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
CAUTION
Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent
type recommended by the manufacturer.
Discard used batteries according to the
manufacturer's instructions.
96 Quick Reference
Indicators for the LCD screen and viewfinder
Indicators Meanings
y60min Remaining battery time
(p. 22)
Quick Reference
SP LP Recording mode (p. 22)
STBY REC Recording standby/
recording mode
Mirror mode (p. 24)
Tape photo recording
(p. 25)
Format indicator
Audio mode (p. 54)
Remaining tape (p. 22)
Interval recording (p. 56)
Frame recording (p. 55)
DV input (p. 68)
Zero set memory (p. 40)
Built-light (p. 23)
NightShot plus (p. 28)
Quick Reference 97
D L
Index Data code (DATA CODE)
...............................37, 59
Language
( LANGUAGE)
Date search.........................41 ........................ 19, 58
Numerics Date/time............................37 LCD back light (LCD B.L.)
16:9 WIDE mode ........ 47, 49 DEMO MODE...................58 .................................... 53
Digital program editing LCD brightness
A (VIDEO EDIT) ...........69 (LCD BRIGHT).......... 16
A/V connecting cable Digital zoom (D ZOOM) ...47 LCD COLOR .................... 53
........................ 39, 61, 62 Digital8 system ..................82 LCD screen.......................... 3
AC Adaptor ....................... 15 Display LP (Long Play)
Adjusting the viewfinder... 16 DISPLAY....................60 See Recording mode
AUDIO MIX ..................... 52 Display indicator .........97 (REC MODE)
AUDIO MODE ................. 54 DNR ...................................52 LTR SIZE .......................... 57
AUTO DATE .................... 57 Dual sound track tape ........51
AUTO SHTR .................... 46 Dubbing .............................61 M
Auto shut off function Main sound
(A.SHUT OFF)........... 59 E See HiFi SOUND
Easy Dubbing.....................64 Menu.................................. 43
B Easy Handycam ...........26, 36 CAMERA SET ........... 47
BACK LIGHT................... 27 EDIT ..................................51 LCD SET .................... 53
Battery END SEARCH ..................33 MANUAL SET........... 44
Battery Info................. 13 Exposure ............................27 OTHERS..................... 59
Battery pack................ 12 PLAYER SET............. 51
Remaining battery time F SETUP MENU ........... 57
....................... 22, 83 FADER ..............................30 TAPE SET .................. 54
BEEP ................................. 59 Focus..................................29 VCR SET .................... 51
BLACK FADER ............... 30 Frame recording Mirror mode ...................... 24
Built-in light ...................... 23 (FRAME REC) ...........55 Moisture condensation ...... 86
BURN DVD/VCD ............ 93 Full charge .........................12 Monaural ..................... 21, 40
Button-type battery MONOTONE FADER ...... 31
Commander ................ 87 MOSAIC FADER ............. 30
G
Remote Commander ... 95
Grip belt ...............................4
N
C NightShot Light
H
Camera settings data display (N.S. LIGHT) ....... 29, 50
Hi8/standard 8 mm system
.................................... 37 NightShot plus................... 28
.....................................82
Cassette ....................... 18, 82 NTSC................................. 81
HiFi SOUND .....................51
Charging the battery
Battery Pack................ 12 O
Pre-installed button-type I
i.LINK................................84 Operation confirmation beep
battery .................. 87 See BEEP
Cleaning cassette............... 87 i.LINK cable ................62, 69
ID-1/ID-2 system ...............49 ORC................................... 54
Clock set (CLOCK SET)
.............................. 17, 57 “InfoLITHIUM” battery pack
COMMANDER ................ 60 .....................................83
Infrared ray emitter ......64, 70
Interval recording
(INT. REC)..................56
98 Quick Reference
P U
PAL ....................................81 USB jack............................ 92
Photo scan ..........................42 USB Streaming
Photo search .......................41 (USB STEAM) ........... 57
Picture effect Using abroad...................... 81
(P EFFECT) ................45
Picture search .....................35 V
Playing time .......................14 Video head......................... 86
Power mode .......................15 Viewfinder......................... 16
PROGRAM AE .................44 Volume .............................. 34
R W
Recording capacity Warning indicators ............ 79
Display ........................22 Warning messages ............. 80
REMAIN .....................55 WHITE FADER ................ 30
Recording lamp Wide angle
(REC LAMP) ..............60 See Zoom
Recording mode WORLD TIME.................. 59
(REC MODE)........22, 54 Write-protect tab................ 82
Recording time...................13
Remote Commander ..........95 Z
Remote sensor....................92 Zero set memory................ 40
RESET ...............................93 Zoom ................................. 23
S
S video .........................40, 62
Self-diagnosis display ........79
Setting the date and time....17
Skip scan ............................35
SP (Standard Play)
Quick Reference
See Recording mode
(REC MODE)
STEADYSHOT .................50
Stereo ...........................21, 40
STRIPE FADER ................31
Sub sound
See HiFi SOUND
T
Tape counter ......................22
Tape photo recording .........25
TBC....................................52
Telephoto
See Zoom
Time code ..........................22
Title ....................................31
TV color systems ...............81
Quick Reference 99
Printed in Japan
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar
Finding a text
1. Click the Find button . Moving with link
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool .
Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists
To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or
select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing
“Find”. page), and the pointer will change to the forefinger form .
3. Then, click the link. (You will go to the link destination.)
Switching a page
• To move to the first page, click the .
• To move to the last page, click the . “Rotate”
• To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each.
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2003.11 Official Release — —