Professional Documents
Culture Documents
How to use
Acrobat Reader
Link
Before starting adjustment VIDEO SECTION ADJUSTMENT
Adjusting items when replacing main parts and boards PREPARATIONS BEFORE ADJUSTMENTS
2003H1600-1
©2003.8
9-876-273-51 Sony EMCS Co. Published by DI CS Strategy Div.
DCR-DVD100/DVD100E
TABLE OF CONTENTS
6. ADJUSTMENT 6-2. VIDEO SECTION ADJUSTMENT ······························ 6-36
1. Before starting adjustment ··············································· 6-1 2-1. PREPARATIONS BEFORE ADJUSTMENTS ············ 6-36
1-1. Adjusting items when replacing main parts and boards. ··· 6-2 2-1-1. Equipment to Required ·················································· 6-36
6-1. CAMERA SECTION ADJUSTMENT ··························· 6-4 2-1-2. Precautions on Adjusting ··············································· 6-37
1-1. PREPARATIONS BEFORE ADJUSTMENT 2-1-3. Adjusting Connectors ···················································· 6-38
(CAMERA SECTION) ··················································· 6-4 2-1-4. Connecting the Equipment ············································ 6-38
1-1-1. List of Service Tools ························································ 6-4 2-1-5. Input/Output Level and Impedance ······························· 6-39
1-1-2. Preparations ····································································· 6-5 2-2. VIDEO SYSTEM ADJUSTMENTS ····························· 6-40
1-1-3. Precaution ········································································ 6-7 1. S VIDEO OUT Y Level Adjustment (VC-307 Board) ····· 6-40
1. Setting the Switch ···························································· 6-7 2. S VIDEO OUT Chroma Level Adjustment
2. Order of Adjustments ······················································ 6-7 (VC-307 Board) ····························································· 6-40
3. Subjects ··········································································· 6-7 3. VIDEO OUT Y, Chroma Level Check (VC-307 Board) ·· 6-41
1-2. INITIALIZATION OF A, B, C, D, E, F, 1F PAGE DATA ·· 6-8 2-3. AUDIO SYSTEM ADJUSTMENTS ···························· 6-42
1-2-1. INITIALIZATION OF A, B, C, D PAGE DATA ············ 6-8 1. Overall Level Characteristics Check ····························· 6-42
1. Initializing the A, B, C, D Page Data ······························ 6-8 2. Overall Distortion Check ··············································· 6-42
2. Modification of A, B, C, D Page Data ····························· 6-8 3. Overall Noise Level Check ············································ 6-42
3. A Page Table ···································································· 6-9 6-3. SERVICE MODE ·························································· 6-43
4. B Page Table ···································································· 6-9 3-1. ADJUSTMENT REMOTE COMMANDER ················ 6-43
5. C Page Table ·································································· 6-10 1. Using the adjustment remote commander ····················· 6-43
6. D Page Table ·································································· 6-10 2. Precautions upon using the adjustment
1-2-2. INITIALIZATION OF E, F, 1F PAGE DATA ··············· 6-11 remote commander ························································ 6-43
1. Initializing the E, F, 1F Page Data ································· 6-11 3-2. DATA PROCESS ··························································· 6-44
2. Modification of E, F, 1F Page Data ······························· 6-11 3-3. SERVICE MODE ·························································· 6-45
3. E Page Table ·································································· 6-11 1. Setting the Test Mode ···················································· 6-45
4. F Page Table ·································································· 6-12 2. Bit value discrimination ················································ 6-45
5. 1F Page Table ································································ 6-13 3. Switch check (1) ···························································· 6-46
1-3. CAMERA SYSTEM ADJUSTMENTS ························ 6-14 4. Switch check (2) ···························································· 6-46
1. 36MHz Origin Oscillation Adjustment (VC-307 board) ··· 6-14 5. Switch check (3) ···························································· 6-46
2. HALL Adjustment ························································· 6-14 6. Switch check (4) ···························································· 6-47
3. Flange Back Adjustment (Using Minipattern Box) ······· 6-15 7. Record of Use check ······················································ 6-47
4. Flange Back Adjustment (Using Flange Back Adjustment 8. Record of Self-diagnosis check ····································· 6-48
Chart and Subject More Than 500m Away) ·················· 6-16
4-1. Flange Back Adjustment (1) ·········································· 6-16
4-2. Flange Back Adjustment (2) ·········································· 6-16 * Optical axis frame and Color reproduction frame are
5. Flange Back Check ························································ 6-17 shown on pages 6-49 and 6-50.
6. Optical Axis Adjustment ··············································· 6-18
7. Mechanical Shutter Adjustment ···································· 6-19
8. Picture Frame Setting ···················································· 6-20
9. Color Reproduction Adjustment ···································· 6-21
10. MAX GAIN Adjustment ··············································· 6-22
11. LV Standard Data Input ················································· 6-22
12. Picture Frame Setting (All White Frame) ····················· 6-23
13. Auto White Balance Standard Data Input ····················· 6-23
14. Auto White Balance Adjustment ··································· 6-24
15. White Balance Check ···················································· 6-25
16. Steady Shot Check ························································· 6-26
1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM
ADJUSTMENT ····························································· 6-27
1. VCO Adjustment (VC-307 board) ································ 6-28
2. RGB AMP Adjustment (VC-307 board) ······················· 6-29
3. Contrast Adjustment (VC-307 board) ··························· 6-29
4. White Balance Adjustment (VC-307 board) ················· 6-30
1-5. LCD SYSTEM ADJUSTMENT ··································· 6-31
1. VCO Adjustment (PD-188 board) ································· 6-31
2. Bright Adjustment (PD-188 board) ······························· 6-32
3. Black Limit Adjustment (PD-188 board) ······················ 6-32
4. PSIG GLAY Adjustment (PD-188 board) ····················· 6-33
5. Contrast Adjustment (PD-188 board) ···························· 6-33
6. Center Level Adjustment (PD-188 board) ····················· 6-34
7. V COM Adjustment (PD-188 board) ···························· 6-34
8. White Balance Adjustment (PD-188 board) ·················· 6-35
—2—
DCR-DVD100/DVD100E
COVER SECTION 6
ADJUSTMENTS
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board
is replaced.
(Machine before starting repair) (Machine after a board is replaced)
PC PC
Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM
to the replaced board.
Remove the EEPROM and install it.
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or
installed, save the data from the same model of the same destination, and download it.
6-1
DCR-DVD100/DVD100E
COVER
Lens device
Base unit
Table. 6-1-1(1).
6-2
DCR-DVD100/DVD100E
Supportng
Initialization of A, B, C, Initialization of A, B, C, D page data z z
D, E, F, 1F page data Initialization of E, F, 1F page data z z
36MHz origin oscillation adj. z z
HALL adj. z z z
Flange back adj. z z z z
Optical axis adj. z z z
Mechanical shutter adj. z z z
Camera Color reproduction adj. z z z
MAX GAIN adj. z z z z
LV standard data input z z z z
AWB standard data input z z z z
Auto white balance adj. z z z z
Steady shot check z z z z
VCO adj. z z
RGB AMP adj. z z
Color EVF
Contrast adj. z z
White balance adj. z z z
VCO adj. z z z
Bright adj. z z z
Black limit adj. z z z
PSIG GRAY adj. z z z
LCD
Contrast adj. z z z
Center level adj. z z z
V COM adj. z z z
White balance adj. z z z
S VIDEO OUT Y level adj. z z
Video
S VIDEO OUT chroma level adj. z z
Table. 6-1-1(2).
6-3
DCR-DVD100/DVD100E
COVER
J-11
Fig. 6-1-1.
6-4
DCR-DVD100/DVD100E
1-1-2. Preparations
Note1: For details of how remove the cabinet and boards, refer to “2. Pattern box
DISASSEMBLY”.
Note2: When performing only the adjustments, the lens block and boards
need not be disassembled.
Note3: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
6-5
DCR-DVD100/DVD100E
[CONNECTION OF EQUIPMENT]
DC-IN connector
Adjustment remote
commander (RM-95)
CPC lid
(bottom)
LANC jack
Screw
(M1.7 × 4),
CPC-8 jig lock ace, p2
(J-6082-388-A)
AC power
adaptor AC IN
Fig. 6-1-3.
6-6
DCR-DVD100/DVD100E
1-1-3. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
1. MODE dial (PS-CX5500 block) ..................... MOVIE ( ) 8. DEMO MODE (Menu setting) ........................................ OFF
2. NIGHT SHOT (Lens block) ............................................ OFF 9. PROGRAM AE (Menu setting) ................................... AUTO
3. COLOR SLOW S/ SUPER NS ........................................ OFF 10. PICTURE EFECT (Menu setting) ................................... OFF
4. FOCUS (KP-CX5500 block) ................................ MANUAL 11. DIGITAL EFECT (Menu setting) .................................... OFF
5. BACK LIGHT (FB-220 board) ........................................ OFF 12. WHITE BALANCE (Menu setting) ............................ AUTO
6. STEADY SHOT (Menu setting) ...................................... OFF 13. 16:9 WIDE (Menu setting) .............................................. OFF
7. DIGITAL ZOOM (Menu setting) .................................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Magenta
White
Cyan
Green
C C=D D
Red
Blue
Magenta
Yellow
Green
White
Cyan
Blue
Red
CRT picture frame
V
A B A=B B A
Fig. b (TV monitor picture)
Fig. a Enlargement
(Video output terminal
output waveform)
Difference in level
Fig. 6-1-4.
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction White
adjustment frame)
2) Clear chart (Color reproduction adjustment frame) 841mm
Remove the color bar chart from the pattern box and insert a Black
clear chart in its place. (Do not perform zoom operations during
this time.)
3) Flange back adjustment chart
1189mm
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm ×
841mm) black and white vellum paper.
Fig. 6-1-5.
Note: Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
6-7
DCR-DVD100/DVD100E
COVER
1-2. INITIALIZATION OF A, B, C, D, E, F, 1F
PAGE DATA
Note: When reading or writing the 1F page data, select page: 0, address:
10, and set data: 01, then select F page. The 1F page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
6-8
DCR-DVD100/DVD100E
6-9
DCR-DVD100/DVD100E
6-10
DCR-DVD100/DVD100E
6-11
DCR-DVD100/DVD100E
4. F Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Address Initial value Remark
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 1F
Page Data”.) NTSC PAL
Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 46 FF FF Optical axis adj.
1F Page Data”). 47 to 4B Fixed data-1
4C 19 19 HALL adj.
Address Initial value Remark 4D to 4F Fixed data-1
NTSC PAL 50 80 80 Mechanical shutter adj.
00 to 0F 51 80 80
10 80 80 36MHz origin osc. adj. 52 80 80
11 to 12 Fixed data-1 53 80 80
13 81 81 HALL adj. 54 80 80
14 5D 5D 55 80 80
15 88 88 56 40 40
16 Fixed data-1 57 00 00
17 9A 9A MAX GAIN adj. 58 34 34
18 80 80 LV standard data input 59 00 00
19 91 7A 5A 30 30
1A 1B 1B AWB standard data input 5B 00 00
1B 00 00 5C 2A 2A
1C 07 07 5D 00 00
1D 00 00 5E 14 14
1E 0E 0E Auto white balance adj. 5F 00 00
1F 00 00 60 70 70
20 0D 0D 61 80 80
21 00 00 62 80 80
22 Fixed data-1 63 80 80
23 22 22 Color reproduction adj. 64 80 80
24 Fixed data-1 65 1E 1E
25 27 24 Color reproduction adj. 66 to 83 Fixed data-1
26 to 29 Fixed data-1 84 Fixed data-2
2A 00 00 Color reproduction adj. 85
2B F1 EF 86 to 89 Fixed data-1
2E to 31 Fixed data-1 8A Fixed data-2
2E 2B 2A Auto white balance adj. 8B
2F C0 40 8C to 8D Fixed data-1
30 59 58 8E Fixed data-2
31 00 C0 8F to 90 Fixed data-1
32 19 19 Flange back adj. 91 Fixed data-2
33 51 51 92 (Modified data. Copy the data
34 20 20 93 built in the same model.)
35 22 22 94 Fixed data-1
36 13 13 95 Fixed data-2
37 93 93 96 to 9D Fixed data-1
38 00 00 9E Fixed data-2
39 00 00 9F Fixed data-1
3A 00 00 A0 Fixed data-2
3B 00 00 A1 to A3 Fixed data-1
3C 46 46 A4 Fixed data-2
3D 19 19 A5 to A6 Fixed data-1
3E 00 00 A7 Fixed data-2
3F 2A 2A A8 (Modified data. Copy the data
40 00 00 A9 built in the same model.)
41 00 00 AA
42 00 00 AB Fixed data-1
43 to 45 Fixed data-1 AC Fixed data-2
6-12
DCR-DVD100/DVD100E
F Page
5. 1F Page Table
Note1: When reading or writing the 1F page data, select page: 0, address:
Address Initial value Remark
10, and set data: 01, then select F page. The 1F page can be chosen
NTSC PAL by this data setting.
AD to B6 Fixed data-1 After reading or writing, reset the data of page: 0, address: 10 to
B7 Fixed data-2 “00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 1F
B8 Page Data”.)
B9 to BC Fixed data-1 Fixed data-2: Modified data. (Refer to “2. Modification of E, F,
BD Fixed data-2 1F Page Data”).
BE
Address Remark
BF
C0 to C5 Fixed data-1 00 to 74 Fixed data-1
C6 Fixed data-2 75 Fixed data-2
C7 (Modified data. Copy the data 76 to D6 Fixed data-1
C8 built in the same model.) D7 Fixed data-2
C9 to CD Fixed data-1 D8 to F7 Fixed data-1
CE Fixed data-2 Table. 6-1-8.
CF
D0 to E3 Fixed data-1
E4 Fixed data-2
E5
E6 Fixed data-1
E7 Fixed data-2
E8 to EF Fixed data-1
F0 Fixed data-2
F1 (Modified data. Copy the data
F2 built in the same model.)
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Table. 6-1-7.
6-13
DCR-DVD100/DVD100E
COVER
6-14
DCR-DVD100/DVD100E
Switch setting:
1) MODE ............................................................. MOVIE ( )
2) NIGHT SHOT .................................................................. OFF
Specified voltage: Note6: The adjustment data will be automatically input to page: F, address:
The specified voltage varies according to the minipattern box, so 32 to 42.
adjust the power supply output voltage to the specified voltage
written on the sheet which is supplied with the minipattern box. Processing after Completing Adjustments:
Order Page Address Data Procedure
Below 3 cm 1 6 48 00 Set the data.
2 0 01 00 Set the data.
Minipattern box
3 Turn off the power and turn on
again.
Camcorder
4 Perform “Flange Back Check”.
Camera
table
Red (+)
Black (–)
Yellow (SENS +)
Fig. 6-1-7.
6-15
DCR-DVD100/DVD100E
4-1. Flange Back Adjustment (1) 4-2. Flange Back Adjustment (2)
Subject Flange back adjustment chart Perform this adjustment after performing “Flange Back Adjustment
(2.0 m from the front of the protection (1)”.
glass) Subject Subject more than 500m away
(Luminance: 350 ± 50 lux) (Subjects with clear contrast such as
Measuring Instrument Adjustment remote commander buildings, etc.)
Adjustment Page F Measurement Point Check operation on TV monitor
Adjustment Address 32 to 42 Measuring Instrument
Adjustment Page F
Note1: This adjustment should be carried out upon completion of “HALL Adjustment Address 32 to 42
Adjustment”.
Note2: Make the lens horizontal and perform this adjustment.
Note1: Make the lens horizontal and perform this adjustment.
Note3: The data of page: 0, address: 10 must be “00”.
Note2: The data of page: 0, address: 10 must be “00”.
Note4: Check that the data of page: 6, address: 02 is “00”. If not, turn off
Note3: Check that the data of page: 6, address: 02 is “00”, turn off the
the power and turn on again.
power and turn on again.
6-16
DCR-DVD100/DVD100E
Switch setting:
1) MODE ............................................................. MOVIE ( )
2) NIGHT SHOT .................................................................. OFF
Note2: When the auto focus is ON, the lens can be checked if it is focused
or not by observing the data on the page 1 of the adjustment remote
commander.
1) Select page: 0, address: 03, and set data: 0F.
2) Page 1 shows the state of the focus.
1 : 00 : XX
Odd: Focused
Even: Unfocused
Checking method:
1) Select page: 6, address: 40, and set data: 01.
2) Select page: 6, address: 41, and set data: 01.
3) Place the Siemens star 2.0m from the front of the lens.
4) To open the IRIS, decrease the luminous intensity to the
Siemens star up to a point before noise appear on the image.
5) Shoot the Siemens star with the zoom TELE end.
6) Turn on the auto focus.
7) Check that the lens is focused (Note2).
8) Select page: 6, address: 21, and set data: 10.
9) Shoot the Siemens star with the zoom WIDE end.
10) Observe the TV monitor and check that the lens is focused.
6-17
DCR-DVD100/DVD100E
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: F, address: 46, set data: 00, and press the PAUSE
button.
3) Place the Siemens star 2.0 m away from the front of the lens.
4) Shoot the Siemens star with the zoom TELE end.
5) Point the lens toward the Siemens star chart until center of the
Siemens star is located in the center of the optical axis frame.
6) Shoot the Siemens star with the zoom WIDE end.
7) Measure on the monitor TV screen in which area of the optical
axis frame the center of the Siemens star is located. Measure
the amount of displacement (distance between the center of
the Siemens star and the center of the optical axis frame.) The
measurement value is named L1.
8) Read the correction data corresponding to the area from Table
6-1-9.
9) Input the correction data to page: F, address: 46, and press the
PAUSE button
10) Shoot the Siemens star with the zoom TELE end.
11) Point the lens toward the Siemens star chart until center of the
Siemens star is located in the center of the optical axis frame.
12) Shoot the Siemens star with the zoom WIDE end.
Fig. 6-1-8.
13) Measure the amount of displacement (distance between the
center of the Siemens star and the center of the optical axis
frame.) The measurement value is named L2.
14) Compare the values L1 and L2, and confirm that L2 is smaller
than L1. If L2 is lager than L1, select page: F, address: 46, set
data: 00, and press the PAUSE button.
6-18
DCR-DVD100/DVD100E
Adjustment Page F
Adjustment Address 50 to 65
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Input the following data to page: F, addresses: 50 to 65.
Note: Press the PAUSE button of the adjustment remote commander
each time to set the data.
Data
Address
NTSC PAL
50 80 80
51 80 80
52 80 80
53 80 80
54 80 80
55 80 80
56 40 40
57 00 00
58 34 34
59 00 00
5A 30 30
5B 00 00
5C 2A 2A
5D 00 00
5E 14 14
5F 00 00
60 70 70
61 80 80
62 80 80
63 80 80
64 80 80
65 1E 1E
3) Select page: 0, address: 01, and set data: 00.
6-19
DCR-DVD100/DVD100E
Setting method:
1) Select page: 6, address: 48, and set data: 02.
2) Adjust the zoom and the camera direction, and set to the
specified position.
3) Mark the position of the picture frame on the monitor display,
and adjust the picture frame to this position in following
adjustments using “Color reproduction adjustment frame”.
Fig. 6-1-9.
2. Vertical period
E E=F F
Fig. 6-1-10.
Fig. 6-1-11.
6-20
DCR-DVD100/DVD100E
Switch setting:
1) MODE ............................................................. MOVIE ( ) Burst position
2) NIGHT SHOT .................................................................. OFF
3) FOCUS .................................................................. MANUAL
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ...................................... OFF
For PAL model
Adjusting method:
1) Select page: 0, address: 01, and set data: 01. Burst position
2) Select page: 6, address: 48, and set data: 02.
3) Select page: 6, address: 9D, and set data: 25.
4) Select page: 6, address: 01, set data: 3D, and press the PAUSE
button.
5) Select page: F, address: 80, set the following data, and press
the PAUSE button.
37 (NTSC), B7 (PAL)
6) Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the color
reproduction frame.
7) Change the data of page: F, address: 23, 25, 2A and 2B, and
settle each color luminance point in each color reproduction
frame.
Note: Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new data
will not be written to the memory.
Fig. 6-1-12.
Processing after Completing Adjustments:
1) Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
2) Select page: 6, address: 48, and set data: 00.
3) Select page: 6, address: 9D, and set data: 00.
4) Select page: 0, address: 01, and set data: 00.
6-21
DCR-DVD100/DVD100E
6-22
DCR-DVD100/DVD100E
12. Picture Frame Setting (All White Frame) 13. Auto White Balance Standard Data Input
When performing “Auto White Balance Standard Data Input”, “Auto Adjust the white balance reference at 3200K.
White Balance Adjustment” and “White Balance Check”, set the Subject Clear chart (All white frame) (Note4)
picture frame to “All white frame”.
Adjustment Page F
Subject Clear chart (All white frame)
Adjustment Address 1A to 1D
(1.5m from the front of the lens)
Measurement Point Video terminal of AUDIO/VIDEO jack Note1: This adjustment should be carried out upon completion of “Color
Measuring Instrument TV monitor (Under scan mode) Reproduction Adjustment”.
Note2: The data of page: 0, address: 10 must be “00”.
Specified Value Whole of the screen is white Note3: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Note: The data of page: 0, address: 10 must be “00”. Note4: Perform “12. Picture Frame Setting (All White Frame)” before
this adjustment.
Switch setting:
1) MODE ............................................................. MOVIE ( ) Switch setting:
2) NIGHT SHOT .................................................................. OFF 1) MODE ............................................................. MOVIE ( )
3) FOCUS .................................................................. MANUAL 2) NIGHT SHOT .................................................................. OFF
4) DIGITAL ZOOM (Menu setting) .................................... OFF 3) FOCUS .................................................................. MANUAL
5) STEADY SHOT (Menu setting) ...................................... OFF 4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ...................................... OFF
Setting method:
Order Page Address Data Procedure Adjusting method:
1 6 48 02 Set the data. Order Page Address Data Procedure
2 6 90 2D Set the data. 1 6 48 02 Set the data.
3 6 91 03 Set the data. 2 Check that the whole of the screen
4 6 92 8E Set the data. is white. If not, perform “12.
Picture Frame Setting (All White
5 6 93 26 Set the data. Frame)”.
6 6 01 79 Set the data, and press PAUSE 3 0 01 01 Set the data.
button.
4 Wait for more than 2 sec.
7 Check that the whole of the
5 6 01 11 Set the data, and press PAUSE
screen is white.
button.
8 Perform the following adjustments.
6 6 01 0B Set the data, and press PAUSE
Processing after Completing Adjustments button.
After completing “Auto White Balance Standard Data Input”, “Auto 7 6 02 Check that the data changes to
White Balance Adjustment” and “White Balance Check”, release “01”. (Note5)
the data setting. 8 Perform “Auto White Balance
Order Page Address Data Procedure Adjustment”.
1 6 48 00 Set the data.
Note5: The adjustment data will be automatically input to page: F, address:
2 6 90 00 Set the data. 1A to 1D.
3 6 91 00 Set the data.
4 6 92 00 Set the data.
5 6 93 00 Set the data.
6-23
DCR-DVD100/DVD100E
6-24
DCR-DVD100/DVD100E
Switch setting:
1) MODE ............................................................. MOVIE ( )
2) NIGHT SHOT .................................................................. OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADY SHOT (Menu setting) ...................................... OFF
Checking method:
Order Page Address Data Procedure
Indoor white balance check
1 Check that the lens is not covered
with either filter.
2 6 48 02 Set the data.
R-Y 2mm
3 6 01 0F Set the data, and press PAUSE
button.
4 Check that the center of the white B-Y
luminance point is within the
circle shown Fig. 6-1-13. A.
5 6 01 00 Set the data, and press PAUSE 2mm
button.
Outdoor white balance check Fig. 6-1-13 (A).
6 Place the C14 filter on the lens.
7 6 01 3F Set the data, and press PAUSE
button. R-Y
1mm
8 Check that the center of the
white luminance point is within
B-Y
the circle shown Fig. 6-1-13. B. 0.5mm
9 Remove the C14 filter. 3mm
LV data check
10 Place the ND filter 1.5 3mm
(1.0+0.1+0.4) on the lens.
11 6 01 00 Set the data, and press PAUSE Fig. 6-1-13 (B).
button.
12 0 03 06 Set the data.
13 1 Check that the display data
(Note3) satisfies the specified
value.
Specified value: 8000 to 8BC0
6-25
DCR-DVD100/DVD100E
Switch setting:
1) STEADY SHOT (Menu setting) ....................................... ON
2) ZOOM .................................................................... TELE end
Adjusting method:
Order Page Address Data Procedure
Pitch sensor check
(MA-420 board SE5502)
1 0 03 11 Set the data.
2 1 Check that the display data
(Note1) satisfies the specified
value. (Note3)
Yaw sensor check
(MA-420 board SE5501)
3 0 03 12 Set the data.
4 1 Check that the display data
(Note1) satisfies the specified
value. (Note3)
5 0 03 00 Set the data.
6 Move the camcorder, and check
that the steady shot operations
have been performed normally
6-26
DCR-DVD100/DVD100E
COVER
Switch setting:
LCD panel .................................................................... Closed
[Adjusting connector]
Most of the measuring points for adjusting the viewfinder system
are concentrated in CN1003 of VC-307 board.
Connect the Measuring Instruments via the CPC-8 jig (J-6082-388-
A).
The following table shows the Pin No. and signal name of CN1003.
Pin No.
19 1
Pin No. Signal Name Pin No. Signal Name
1 GND 2 GND
3 PANEL VG 4 H START
20 2
5 XHD/PSIG 6 EVF VG
7 EVF VCO 8 EVF BL
9 D 3.1V 10 LANC SIG
11 MS XIN 12 MS DIO
13 MS BS 14 MS VCC ON Fig. 6-1-14.
15 MS SCLK 16 ACCESS LED
17 C PIO5 18 C PIO4
19 S TXD 20 S RXD
Table 6-1-10.
6-27
DCR-DVD100/DVD100E
Adjusting method for NTSC model: Adjusting method for PAL model:
Order Page Address Data Procedure Order Page Address Data Procedure
1 0 01 01 Set the data. 1 0 01 01 Set the data.
2 B 51 Change the data and set the VCO 2 B 52 Change the data and set the VCO
frequency (f) to the specified frequency (f) to the specified
value. value.
3 B 51 Press PAUSE button. 3 B 52 Press PAUSE button.
4 B 51 Read the data, and this data is 4 B 52 Read the data, and this data is
named D51. named D52.
5 Convert D51 to decimal notation, 5 Convert D52 to decimal notation,
and obtain D51’. (Note2) and obtain D52’. (Note2)
6 Calculate D52’ using following 6 Calculate D51’ using following
equations (Decimal calculation) equations (Decimal calculation)
When D51’ 231 When D52’ 24
D52’ = D51’ + 24 D51’ = D52’– 24
When D51’ > 231 When D52’ < 24
D52’ = 255 D51’ = 0
7 Convert D 52’ to a hexadecimal 7 Convert D51’ to a hexadecimal
number, and obtain D52. (Note2) number, and obtain D51. (Note2)
8 B 52 D52 Set the data, and press PAUSE 8 B 51 D51 Set the data, and press PAUSE
button. button.
9 0 01 00 Set the data. 9 0 01 00 Set the data.
6-28
DCR-DVD100/DVD100E
Note: The data of page: 0, address: 10 must be “00”. Note: The data of page: 0, address: 10 must be “00”.
Pedestal
A 100 IRE
2H
2H
Pedestal
Pedestal
6-29
DCR-DVD100/DVD100E
Note1: Check the white balance only when replacing the following parts.
If necessary, adjust them.
1. LCD panel
2. Light induction plate
3. IC2201
Note2: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 B 56 8D Set the data, and press PAUSE
button.
3 B 57 73 Set the data, and press PAUSE
button.
4 B 57 Check that the EVF screen is not
colored. If not colored, proceed to
step 10.
5 B 56 Change the data so that the EVF
screen is not colored.
6 B 56 Press PAUSE button.
7 B 57 Change the data so that the EVF
screen is not colored.
8 B 57 Press PAUSE button.
9 B 57 If the EVF screen is colored,
repeat steps 5 to 9.
10 0 01 00 Set the data.
6-30
DCR-DVD100/DVD100E
COVER
6-31
DCR-DVD100/DVD100E
Pedestal
Fig. 6-1-19.
A
2H
Pedestal
Fig. 6-1-18.
6-32
DCR-DVD100/DVD100E
2H
100 IRE
Fig. 6-1-20.
2H
Pedestal
Fig. 6-1-21.
6-33
DCR-DVD100/DVD100E
Adjusting method: Note1: This adjustment should be carried out upon completion of the
Order Page Address Data Procedure following adjustments.
Bright Adjustment
1 0 01 01 Set the data. Black Limit Adjustment
2 B 6A Change the data and set the DC Contrast Adjustment
voltage (A) to the specified value. Center Level Adjustment
Note2: The data of page: 0, address: 10 must be “00”.
(The data should be “00” to “7F”.)
3 B 6A Press PAUSE button. Adjusting method:
4 0 01 00 Set the data. Order Page Address Data Procedure
1 0 01 01 Set the data.
2 B 63 Change the data so that the
brightness of the section A and
that of the section B is equal.
(Note3)
3 B 63 Subtract 2 from the data. (Note3)
4 B 63 Press PAUSE button.
5 0 01 00 Set the data.
B A
A B
B A
A B
Fig. 6-1-22.
6-34
DCR-DVD100/DVD100E
Note1: Check the white balance only when replacing the following parts.
If necessary, adjust them.
1. LCD panel
2. Light induction plate
3. IC6001
Note2: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 B 67 7D Set the data, and press PAUSE
button.
3 B 68 65 Set the data, and press PAUSE
button.
4 B 68 Check that the LCD screen is not
colored. If not colored, proceed to
step 10.
5 B 67 Change the data so that the LCD
screen is not colored.
6 B 67 Press PAUSE button.
7 B 68 Change the data so that the LCD
screen is not colored.
8 B 68 Press PAUSE button.
9 B 68 If the LCD screen is colored,
repeat steps 5 to 9.
10 0 01 00 Set the data.
6-35
DCR-DVD100/DVD100E
COVER
1) TV monitor
2) Oscilloscope (dual-phenomenon, band width above 30 MHz
with delay mode) (Unless specified otherwise, use a 10:1
probe.)
3) Frequency counter
4) Pattern generator with video output terminal
5) Audio generator
6) Audio level meter
7) Audio distortion meter
8) Audio attenuator
9) Adjustment remote commander (J-6082-053-B)
10) Extension cable (100P 0.5mm) (J-6082-352-A)
For extension between the MD-097 board (CN4902) and the
VC-307 board (CN1008)
11) CPC-8 jig (J-6082-388-A)
6-36
DCR-DVD/100DVD100E
2-1-2. Precautions on Adjusting Note2: Setting the “Forced PLAY mode” (PLAY/EDIT mode)
Note1: Before performing the adjustments, check the data of page: 0, 1) Select page: 0, address: 01, and set data: 01.
address: 10 is “00”. If not, set data: 00 to this address. 2) Select page: D, address: 10, set data: 02, and press the PAUSE
1) The adjustments of this unit are performed in the PLAY mode button of the adjusting remote commander.
or MOVIE mode. The above procedure will enable the power to be turned on with the
To set to the PLAY mode, set the mode dial to “PLAY/EDIT” control switch block (PS-CX5500 block) removed.
( ) or set the “Forced PLAY mode” using the adjusting After completing adjustments, be sure to exit the “Forced PLAY
remote commander (Note2). mode”.
To set to the MOVIE mode, set the mode dial to “MOVIE”
Note3: Setting the “Forced MOVIE mode”
( ) or set the “Forced MOVIE mode” using the adjusting 1) Select page: 0, address: 01, and set data: 01.
remote commander (Note3). 2) Select page: D, address: 10, set data: 01, and press the PAUSE
After completing adjustments, be sure to exit the “Forced button of the adjusting remote commander.
MOVIE Mode” or “Forced Camera Power ON Mode”. (Note5) The above procedure will enable the power to be turned on with the
2) The front panel block (Microphones, MA-420 board (S VIDEO control switch block (PS-CX5500 block) removed.
jack, remote commander receiver, infrared LED, angular After completing adjustments, be sure to exit the “Forced MOVIE
velocity sensors)) need not be connected except for the case mode”.
that the S VIDEO jack is used. To remove it, disconnect the
following connector. Note4: Setting the “Forced STILL mode”
MA-420 board CN5503 (22P, 0.5mm) 1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press the PAUSE
3) Cabinet (R) (CK-127 board, LCD block) need not be connected.
button of the adjusting remote commander.
But removing the cabinet (R) (disconnecting the VC-307 board
The above procedure will enable the memory power to be turned on
CN1007) means removing the lithium 3V power supply (CK-
with the control switch block (PS-CX5500 block) removed.
127 board, BT5201), data such as date, time, user-set menus
After completing adjustments, be sure to exit the “Forced STILL
will be lost. After completing adjustments, reset these data.
mode”.
But, the self-diagnosis data and the data on history of use (user
initial power on date, final condensation occurrence data) will Note5: Exiting the “Forced mode”
be kept even if the cabinet (R) has been removed. (Refer to “6- 1) Select page: 0, address: 01, and set data: 01.
3.Service Mode” for the data on the history use and the self- 2) Select page: D, address: 10, set data: 00, and press the PAUSE
diagnosis data.) button of the adjusting remote commander.
To remove the cabinet (R), disconnect the following connectors. 3) Select page: 0, address: 01, and set data: 00.
VC-307 board CN1007 (39P, 0.3mm)
4) The EVF block (LB-084 board) need not be connected. To
remove it, disconnect the following connector.
VC-307 board CN2201 (20P, 0.5mm)
5) The intelligent accessory shoe need not be connected. To
remove it, disconnect the following connector.
VC-307 board CN1001 (10P, 0.5mm)
6) The lens block (CD-428 board) need not be connected. To
remove it, disconnect the following connectors.
VC-307 board CN1301 (24P, 0.5mm)
VC-307 board CN1201 (24P, 0.5mm)
VC-307 board CN1010 (2P, 0.8mm)
7) By setting the “Forced PLAY mode” or the “Forced MOVIE
mode”, the video section can be operate even if the control
switch block (PS-CX5500) has been removed. When removing
it, disconnect the following connector.
VC-307 board CN1002 (14P, 0.5mm)
8) To open the VC-307 board, use the following extension cable
between the VC-307 board CN1008 and MD-097 board
CN4901.
J-6082-352-A (100P, 0.5mm)
6-37
DCR-DVD100/DVD100E
Recording mode
Pattern generator AUDIO/VIDEO jack
VIDEO
Video output (Yellow)
(75 Ω)
AUDIO L
(White)
Main unit
AUDIO R
(Red)
LANC jack
Adjustment
remote
commander Adjustment
remote
Playback mode commander
LANC jack
TV monitor
VIDEO
(Yellow)
Main unit
AUDIO L (White)
AUDIO R (Red)
AUDIO/VIDEO jack
Fig 6-2-2.
6-38
DCR-DVD/100DVD100E
6-39
DCR-DVD100/DVD100E
COVER
2-2. VIDEO SYSTEM ADJUSTMENTS 2. S VIDEO OUT Chroma Level Adjustment (VC-307 Board)
Note1: efore perform the video system adjustments, check that the Mode MOVIE ( )
specified value of “36MHz Origin Oscillation Adjustment” of
“CAMERA SYSTEM ADJUSTMENT” is satisfied. Subject Arbitrary
And check that the data of page: 0, address: 10 is “00”. If not, set Measurement Point Chroma signal terminal of S VIDEO
data: 00 to this address. jack (75Ω terminated)
Note2: NTSC model: DCR-DVD100 External trigger: Y signal terminal of
PAL model: DCR-DVD100E
S VIDEO jack
1. S VIDEO OUT Y Level Adjustment (VC-307 Board) Measuring Instrument Oscilloscope
Mode MOVIE ( ) Adjustment Page B
Subject Arbitrary Adjustment Address 42, 43
Measurement Point Y signal terminal of S VIDEO jack Specified Value Cr level : A = 714 ± 14mV (NTSC)
(75Ω terminated) A = 700 ± 14mV (PAL)
Cb level : B = 714 ± 14mV (NTSC)
Measuring Instrument Oscilloscope B = 700 ± 14mV (PAL)
Adjustment Page B Burst level : C = 286 ± 6mV (NTSC)
Adjustment Address 41 C = 300 ± 6mV (PAL)
Specified Value A = 1000 ± 14mV Note: The data of page: 0, address: 10 must be “00”.
Note: The data of page: 0, address: 10 must be “00”. Switch setting:
Switch setting: DEMO MODE (Menu setting) ........................................ OFF
DEMO MODE (Menu setting) ........................................ OFF Adjusting method:
Adjusting method: Order Page Address Data Procedure
Order Page Address Data Procedure 1 0 01 01 Set the data.
1 0 01 01 Set the data. 2 3 00 00 Set the data.
2 3 00 00 Set the data. 3 3 04 02 Set the data, and press PAUSE
3 3 04 02 Set the data, and press PAUSE button.
button. 4 B 42 Change the data and set the Cr
4 B 41 Change the data and set the Y signal level (A) to the specified
signal level (A) to the specified value.
value. 5 B 42 Press PAUSE button.
5 B 41 Press PAUSE button. 6 B 43 Change the data and set the Cb
6 3 04 00 Set the data, and press PAUSE signal level (B) to the specified
button. value.
7 0 01 00 Set the data. 7 B 43 Press PAUSE button.
8 3 04 00 Set the data, and press PAUSE
button.
9 Check that the burst signal level
(C) is satisfied the specified value.
10 0 01 00 Set the data.
A
C
Fig. 6-2-3.
A B
Switch setting:
DEMO MODE (Menu setting) ........................................ OFF
Adjusting method:
Order Page Address Data Procedure
1 3 00 00 Set the data.
2 3 04 02 Set the data, and press PAUSE
button.
3 Check that the sync signal level
(A) satisfies the specified value.
4 Check that the burst signal level
(B) satisfies the specified value.
5 3 04 00 Set the data, and press PAUSE
button.
B
A
Fig. 6-2-5.
6-41
DCR-DVD100/DVD100E
COVER
6-42
DCR-DVD/100DVD100E
COVER
Fig. 6-3-1
6-43
DCR-DVD100/DVD100E
COVER
Table. 6-3-1.
6-44
DCR-DVD/100DVD100E
COVER
Data Function
00 Normal
01 Forced MOVIE mode ( )
02 Forced PLAY mode ( )
05 Forced STILL mode ( )
• Before setting the data, select page: 0, address: 01, and set data: 01.
• For page D, the data set will be recorded in the non-volatile
memory by pressing the PAUSE button of the adjustment remote
commander. In this case, take note that the test mode will not be
exited even when the main power is turned off.
• After completing adjustments/repairs, be sure to return the data
of this address to 00, and press the PAUSE button of the adjustment
remote commander. And select page: 0, address: 01, and set data:
00.
6-45
DCR-DVD100/DVD100E
Using method:
1) Select page: 7, address: 0C.
2) By discriminating the bit value of display data, the state of the switch can be discriminated.
Using method:
1) Select page: 7, address: 52.
2) By discriminating the bit value of display data, the state of the switch can be discriminated.
6-46
DCR-DVD/100DVD100E
Using method:
1) Select page: 2, address: 60 to 65, 67.
2) By discriminating the display data, the pressed key can be discriminated.
Data
Address 00 19 32 4E 6F 96 EB
(00 to 0C) (0D to 24) (25 to 3F) (40 to 5D) (5F to 81) (82 to AA) (D6 to FF)
PHOTO
60 (PHOTO REC)
(KEY AD0) (PS-CX5500 block) No key input
(IC3103 tl ) (S002)
COLOR SLOW S/
61 BACK LIGHT FADER REVIEW SUPER NS
(KEY AD1) (FB-220 board) (FB-220 board) (FB-220 board) (FP-610 flexible) No key input
(IC3103 y; ) (S5301) (S5303) (S5305) (S9101)
62 STOP PREV PLAY NEXT PAUSE
(KEY AD2) (FB-220 board) (FB-220 board) (FB-220 board) (FB-220 board) (FB-220 board) No key input
(IC3103 ya ) (S5302) (S5304) (S5306) (S5308) (S5310)
63 FOCUS EXPOSURE VISUAL INDEX SET UP REC PANEL CLOSE PANEL OPEN
(KEY AD3) (KP-CX5500 block) (KP-CX5500 block) (CK-127 board) (CK-127 board) (CK-127 board) (CK-127 board) (CK-127 board)
(IC3103 yg ) (S003) (S002) (S5209) (S5210) (S5211) (S5207) (S5207)
PANEL PANEL
64 UP LEFT ENTER RIGHT DOWN REVERSE NORMAL
(KEY AD4) (CK-127 board) (CK-127 board) (CK-127 board) (CK-127 board) (CK-127 board) (FP-612 flexible) (FP-612 flexible)
(IC3103 yh ) (S5212) (S5213) (S5214) (S5215) (S5216) (S9201) (S9201)
65 EDIT VOLUME + VOLUME -
(KEY AD5) (CK-127 board) (CK-127 board) (CK-127 board) No key input
(IC3103 yj ) (S5201) (S5204) (S5205)
67 START/STOP
(KEY AD7) (PS-CX5500 block) No key input
(IC3103 yl ) (S003)
6-47
DCR-DVD100/DVD100E
Page 7 Address B0 to C6
Note1: This data will be kept even if the lithium battery (CK-127 board
BT5201 of the cabinet (R) assembly) is removed.
Note2: The data of page: 0, address: 10 must be “00”.
Using method:
1) The past self-diagnosis codes are displayed at addresses: BC
to C6.
Refer to “SELF-DIAGNOSIS FUNCTION” for detail of the
self-diagnosis code except for the code being written in the
following table.
Self-diagnosis Code
Block Detailed Symptom/State Correction
Repaired by:
Function Code
Data on A page or D page are Make data on A page and D
E 20 00
rewritten. page correct value.
Fault of writing to or erasing the Inspect the flash memory
E 94 00
flash memory (VC-307 board IC3401)
Note: When the fault of writing to or erasing the flash memory (E:94:00) is displayed.
After repair, clear the error information in the following method.
1) Select page:0, address:01, and set data:01.
2) Select page:7, address:00, and set data:EE.
3) Select page:7, address:01, set data:EE and press the PAUSE button.
4) Check that the data of page:7, address:02, changes from “00” to “01”.
5) Select page:0, address:01, and set data:00.
6-48
DCR-DVD100/DVD100E
〈OPTICAL AXIS FRAME〉
6-49
DCR-DVD100/DVD100E
〈FOR CAMERA COLOR REPRODUCTION ADJUSTMENT〉
✂
For PAL model
✂
6-50E
COVER
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar
Switching a page • Select the zoom-out tool and drag a range to be zoomed
• To move to the first page, click the . out.
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2003.08 Official Release — —