Professional Documents
Culture Documents
Link
Before starting adjustment VIDEO SECTION ADJUSTMENT
Adjusting items when replacing main parts and boards PREPARATIONS BEFORE ADJUSTMENTS
DATA PROCESS
MECHANISM SECTION ADJUSTMENT
SERVICE MODE
HOW TO ENTER RECORD MODE WITHOUT ASSETTE
2003C1600-1
©2003.3
9-876-233-51 Sony EMCS Co. Published by DI Customer Center
DCR-TRV60/TRV60E/TRV70
TABLE OF CONTENTS
6. ADJUSTMENT 22. AF Laser Axis Check (1) ··············································· 6-38
1. Before starting adjustment ··············································· 6-1 23. AF Laser Axis Check (2) ··············································· 6-39
1-1. Adjusting items when replacing main parts and boards. · 6-2 1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM
6-1. CAMERA SECTION ADJUSTMENT ··························· 6-4 ADJUSTMENT ····························································· 6-40
1-1. PREPARATIONS BEFORE ADJUSTMENT 1. VCO Adjustment (DI-088 board) ·································· 6-40
(CAMERA SECTION) ··················································· 6-4 1-1. Manual Adjustment ······················································· 6-40
1-1-1. List of Service Tools ························································ 6-4 1-2. Automatic Adjustment ··················································· 6-41
1-1-2. Preparations ····································································· 6-5 2. RGB AMP Adjustment (DI-088 board) ························· 6-42
1-1-3. Precaution ········································································ 6-7 2-1. Automatic Adjustment ··················································· 6-42
1. Setting the Switch ···························································· 6-7 2-2. Manual Adjustment ······················································· 6-42
2. Order of Adjustments ······················································ 6-7 3. Contrast Adjustment (DI-088 board) ····························· 6-43
3. Subjects ··········································································· 6-7 3-1. Automatic Adjustment ··················································· 6-43
4. Preparing the Flash Adjustment Box ······························· 6-8 3-2. Manual Adjustment ······················································· 6-43
1-2. INITIALIZATION OF 8, A, B, C, D, E, F, 18, 1B, 4. White Balance Adjustment (DI-088 board) ··················· 6-44
1C, 1E, 1F PAGE DATA ·················································· 6-9 1-5. LCD SYSTEM ADJUSTMENT ··································· 6-45
1-2-1. INITIALIZATION OF A, D PAGE DATA ···················· 6-10 1. VCO Adjustment (PD-189 board) ································· 6-45
1. Initializing the A, D Page Data ······································ 6-10 1-1. Manual Adjustment ······················································· 6-45
2. Modification of A, D Page Data ···································· 6-10 1-2. Automatic Adjustment ··················································· 6-46
3. A Page Table ·································································· 6-10 2. LCD Automatic Adjustment (PD-189 board) ················ 6-46
4. D Page Table ·································································· 6-11 3. V COM Adjustment (PD-189 board) ···························· 6-47
1-2-2. INITIALIZATION OF B, 1B PAGE DATA ·················· 6-12 4. White Balance Adjustment (PD-189 board) ·················· 6-47
1. Initializing the B, 1B Page Data ···································· 6-12 6-2. MECHANISM SECTION ADJUSTMENT ·················· 6-48
2. Modification of B, 1B Page Data ·································· 6-12 2-1. HOW TO ENTER RECORD MODE WITHOUT
3. Writing the Network Default Setting Value CASSETTE ··································································· 6-48
(DCR-TRV70) ······························································· 6-12 2-2. HOW TO ENTER PLAYBACK MODE
4. B Page Table ·································································· 6-13 WITHOUT CASSETTE ················································ 6-48
5. 1B Page Table ································································ 6-13 2-3. TAPE PATH ADJUSTMENT ········································ 6-48
1-2-3. INITIALIZATION OF 8, C, 18, 1C PAGE DATA ······· 6-14 1. Preparation for Adjustment ··········································· 6-48
1. Initializing the 8, C, 18, 1C Page Data ·························· 6-14 2. Processing after Completing Operations: ······················ 6-48
2. Modification of 8, C, 18, 1C Page Data ························ 6-14 6-3. VIDEO SECTION ADJUSTMENT ······························ 6-49
3. 8 Page Table ··································································· 6-15 3-1. PREPARATIONS BEFORE ADJUSTMENTS ············ 6-49
4. C Page Table ·································································· 6-16 3-1-1. Equipment to Required ·················································· 6-49
5. 18 Page Table ································································· 6-17 3-1-2. Precautions on Adjusting ··············································· 6-50
6. 1C Page Table ································································ 6-17 3-1-3. Adjusting Connectors ···················································· 6-51
1-2-4. INITIALIZATION OF E, F, 1E, 1F PAGE DATA ········ 6-18 3-1-4. Connecting the Equipment ············································ 6-51
1. Initializing the E, F, 1E, 1F Page Data ·························· 6-18 3-1-5. Alignment Tapes ···························································· 6-52
2. Modification of E, F, 1E, 1F Page Data ························· 6-18 3-1-6. Input/Output Level and Impedance ······························· 6-52
3. E Page Table ·································································· 6-19 3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 6-53
4. F Page Table ·································································· 6-20 1. Initialization of 8, A, B, C, D, E, F, 18, 1B, 1C, 1E, 1F
5. 1E Page Table ································································ 6-21 Page Data ······································································· 6-53
6. 1F Page Table ································································ 6-22 2. Touch Panel Adjustment ················································ 6-53
1-3. CAMERA SYSTEM ADJUSTMENTS ························ 6-23 3. Serial No. Input ····························································· 6-53
1. 54MHz/67.5MHz Origin Oscillation Adjustment 3-1. Company ID Input ························································· 6-53
(CD-433 board) ····························································· 6-23 3-2. Serial No. Input ····························································· 6-53
2. HALL Adjustment ························································· 6-23 3-3. SERVO AND RF SYSTEM ADJUSTMENT ··············· 6-55
3. MR Adjustment ····························································· 6-24 1. Cap FG Duty Adjustment (VC-314 Board) ··················· 6-55
4. CCD Output 2ch Matching Adjustment (1) ·················· 6-25 2. Switching Position Adjustment (VC-314 Board) ·········· 6-55
5. CCD Output 2ch Matching Adjustment (2) ·················· 6-25 3. Error Rate Check ··························································· 6-56
6. Flange Back Adjustment (Using Minipattern Box) ······· 6-26 3-1. Preparations before adjustments ···································· 6-56
7. Flange Back Adjustment (Using Flange Back 3-2. Error Rate Check ··························································· 6-56
Adjustment Chart and Subject More Than 500m Away) ·· 6-27 3-3. Processing after Completing Adjustments ···················· 6-56
7-1. Flange Back Adjustment (1) ·········································· 6-27 3-4. VIDEO SYSTEM ADJUSTMENTS ····························· 6-57
7-2. Flange Back Adjustment (2) ·········································· 6-27 1. S VIDEO OUT Y Level Adjustment (VC-314 Board) ·· 6-57
8. Flange Back Check ························································ 6-28 2. S VIDEO OUT Chroma Level Adjustment
9. MAX GAIN Adjustment ··············································· 6-28 (VC-314 Board) ····························································· 6-57
10. Picture Frame Setting 3. VIDEO OUT Y, Chroma Level Check (VC-314 Board) · 6-58
(Color Reproduction Adjustment Frame) ······················ 6-29 3-5. AUDIO SYSTEM ADJUSTMENTS ···························· 6-59
11. Color Reproduction Adjustment ···································· 6-30 1. Playback Level Check ··················································· 6-60
12. LV Standard Data Input ················································· 6-31 2. Overall Level Characteristics Check ····························· 6-60
13. Picture Frame Setting (All White Frame) ····················· 6-32 3. Overall Distortion Check ··············································· 6-60
14. Auto White Balance Standard Data Input ····················· 6-32 4. Overall Noise Level Check ············································ 6-60
15. Auto White Balance Adjustment ··································· 6-33 5. Overall Separation Check ·············································· 6-60
16. White Balance Check ···················································· 6-34 6-4. SERVICE MODE ·························································· 6-61
17. Mechanical Shutter Adjustment ···································· 6-35 4-1. ADJUSTMENT REMOTE COMMANDER ················ 6-61
18. Steady Shot Check ························································· 6-35 1. Using the adjustment remote commander ····················· 6-61
19. Strobe Light Level Adjustment ····································· 6-36 2. Precautions upon using the adjustment
20. Strobe White Balance Adjustment & Check ················· 6-36 remote commander ························································ 6-61
21. AF Laser Output Adjustment ········································ 6-37
—2—
DCR-TRV60/TRV60E/TRV70
—3—
DCR-TRV60/TRV60E/TRV70
COVER SECTION 6
ADJUSTMENTS
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board
is replaced.
(Machine before starting repair) (Machine after a board is replaced)
PC PC
Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM
to the replaced board.
Remove the EEPROM and install it.
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or
installed, save the data from the same model of the same destination, and download it.
(Machine to be repaired) PC (Machine to be repaired)
6-1
DCR-TRV60/TRV60E/TRV70
COVER
1-1. Adjusting items when replacing main parts and boards.
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note1: When replacing the drum assy. or the mechanism deck, reset the data of page: 7, address: A7 to A9 to “00”. (Refer to “Record of
Use check” of “6-4. SERVICE MODE”)
Replaced parts
Block replacement Parts replacement
Supporting
and that there is no difference in
left-right brightness level of the
screen.
When the above symptom occurs,
Initialization of A, D page data z z perform the whole process of “CCD
Initialization of
Initialization of B, 1B page data z z Output 2ch Matching Adjustment”.
8,A,B,C,D,E,F,18,1B,
Initialization of 8, C, 18, 1C page data z z
1C,1E,1F page data Note3: When replacing the VC-314 board,
Initialization of E, F, 1E, 1F page data z z before and after replacing, perform
54MHz/67.5MHz origin oscillation adj. z z “Writing the Network Default
HALL adj. z z z Setting Value” and initialize the
personal network information (Mail
MR adj. z z z address, bookmark etc.). (DCR-
CCD output 2ch matching adj. z z z z TRV70)
Flange back adj. z z z z (Refer to “1-2-2. INITIALIZATION
OF B, 1B PAGE DATA”.)
MAX GAIN adj. z z z z
Camera Color reproduction adj. z z z Note4: When the flash error code (E:91:**)
LV standard data input z z z z is displayed. After repair, clear the
error flag. (Refer to “Record of
Auto white balance standard data input z z z z
Self-diagnosis check” of “6-4.
Auto white balance adj. z z z z SERVICE MODE”.)
Mechanical shutter adj. z z z
Steady shot check z z z z
Strobe light level adjustment z z z
Strobe white balance adjustment & check z z z
AF laser output adj. z z z
VCO adj. z z z z
RGB AMP adj. z z z z
Color EVF
Contrast adj. z z z z
White balance adj. z z z z
VCO adj. z z z z
LCD automatic adj. z z z z
LCD
V COM adj. z z z
White balance adj. z z z
Mechanism Tape path adj.
Touch panel adj. z z
System control
Serial No. input z z
CAP FG duty adj. z z z
Servo, RF Switching position adj. z z z
Error rate check z z z
S VIDEO OUT Y level adj. z z
Video
S VIDEO OUT chroma level adj. z z
Table. 6-1-1 (2).
6-3
DCR-TRV60/TRV60E/TRV70
COVER
J-11 J-12
Fig. 6-1-1.
6-4
DCR-TRV60/TRV60E/TRV70
1-1-2. Preparations
Note1: For details of how remove the cabinet and boards, refer to “2. Pattem box
DISASSEMBLY”.
Note2: When performing only the adjustments, the lens block and boards
need not be disassembled.
Note3: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
1.5 m
1) Connect the equipment for adjustments according to Fig. 6-1-3.
6-5
DCR-TRV60/TRV60E/TRV70
[CONNECTION OF EQUIPMENT]
Adjustment remote
commander (RM-95)
VC-314
board
AC power
AC IN adaptor 1
16
CN1004 CPC lid
Screw
(M1.7 × 4),
lock ace, p2
CPC-7 jig
LANC jack 16 (J-6082-382-A)
DC IN connector
Fig. 6-1-3.
6-6
DCR-TRV60/TRV60E/TRV70
1-1-3. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1. POWER switch (FK-4110 block) .......................... CAMERA WHITE BALANCE ............................................ AUTO
2. NIGHT SHOT switch (FC-092 board) ............................ OFF CAMERA SET of the MENU settings (Page1)
3. FOCUS switch (FP-666 flexible) ..................................... OFF DIGITAL ZOOM .................................................... OFF
4. BACK LIGHT switch (FP-666 flexible) .......................... OFF 16:9 WIDE .............................................................. OFF
5. FUNCTION settings (Touch panel) STEADY SHOT ...................................................... OFF
SPOT METER (Page1) ........................................... AUTO SETUP MENU of the MENU settings (Page1)
EXPOSURE (Page1) .................................................. OFF DEMO MODE ........................................................ OFF
MANUAL SET of the MENU settings (Page1) DIGITAL EFFECT (Page2) ........................................ OFF
PROGRAM ......................................................... AUTO COLOR SS (Page3) .................................................... OFF
PICTURE EFECT ................................................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Magenta
White
Cyan
Green
C C=D D
Red
Blue
Magenta
Yellow
Green
White
Cyan
Blue
Red
CRT picture frame
V
A B A=B B A
Fig. b (TV monitor picture)
Fig. a Enlargement
(Video output terminal
output waveform)
Difference in level
Fig. 6-1-4.
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction White
adjustment frame)
2) Clear chart (Color reproduction adjustment frame) 841mm
Remove the color bar chart from the pattern box and insert a Black
clear chart in its place. (Do not perform zoom operations during
this time.)
3) Flange back adjustment chart
1189mm
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm ×
841mm) black and white vellum paper.
Fig. 6-1-5.
Note: Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
6-7
DCR-TRV60/TRV60E/TRV70
730 mm 700 mm
Fig. 6-1-6
woody board A
woody board B
woody board A
woody board B
woody board C
Fig. 6-1-7
6-8
DCR-TRV60/TRV60E/TRV70
COVER
Battery terminal
Fig. 6-1-8.
6-9
DCR-TRV60/TRV60E/TRV70
1-2-1. INITIALIZATION OF A, D PAGE DATA Processing after Completing Modification of A, D Page data
Order Page Address Data Procedure
Note: The data of page: 0, address: 10 must be “00”.
1 2 00 29 Set the data.
1. Initializing the A, D Page Data 2 2 01 29 Set the data, and press PAUSE
Note1: If “Initializing the A, D Page Data” is performed, all data of the A button.
page and D page will be initialized. (It is impossible to initialize a
single page.) Note: If the following symptoms occur after completing of the
Note2: If the A, D page data has been initialized, the following adjustments “Modification of A, D page data”, check that the data of the “Fixed
need to be performed again. data-2” addresses of A and D page are same as those of the same
1) Modification of A, D page data model of the same destination.
2) Touch panel adjustment 1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.
Note3: The power supply voltage must be 6.3 ± 0.1Vdc. 2) The power is shut off so that unit cannot operate.
6-10
DCR-TRV60/TRV60E/TRV70
4. D Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, D
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of A, D
Page Data”).
Address Remark
Initial value
00 to 0F
10 00 Test mode
11 Fixed data-1
12 Fixed data-2
13 to 15 Fixed data-1
16 Fixed data-2
17 to 22 Fixed data-1
23 Fixed data-2
24 (Modified data. Copy the data
25 built in the same model.)
26
27 to 29 Fixed data-1
2A Fixed data-2
2B
2C to 35 Fixed data-1
36 Fixed data-2
37 (Modified data. Copy the data
38 built in the same model.)
39 Fixed data-1
3A Fixed data-2
3B to 55 Fixed data-1
56 Fixed data-2
57 (Modified data. Copy the data
58 built in the same model.)
59
5A to 63 Fixed data-1
64 Fixed data-2
65
66 to 6E Fixed data-1
6F Fixed data-2
70 to 7F Fixed data-1
Table. 6-1-3.
6-11
DCR-TRV60/TRV60E/TRV70
6-12
DCR-TRV60/TRV60E/TRV70
4. B Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, 1B
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of B, 1B
Page Data”).
Address Remark
00 to 02 Fixed data-1
03 Fixed data-2
04 to AA Fixed data-1
AB Fixed data-2
AC to AF Fixed data-1
B0 Fixed data-2
B1 to B6 Fixed data-1
B7 Fixed data-2
B8 to BA Fixed data-1
BB Fixed data-2
BC Fixed data-1
BD Fixed data-2
BE to FF Fixed data-1
Table. 6-1-4.
5. 1B Page Table
Note1: When reading or writing the 1B page data, select page: 0, address:
10, and set data: 01, then select B page. The 1B page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, 1B
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of B, 1B
Page Data”).
Address Remark
00 Fixed data-2
01 to 24 Fixed data-1
25 Fixed data-2
26 to FF Fixed data-1
Table. 6-1-5.
6-13
DCR-TRV60/TRV60E/TRV70
6-14
DCR-TRV60/TRV60E/TRV70
3. 8 Page Table
Note1: The data of page: 0, address: 10 must be “00”. Address Remark
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C,
18, 1C Page Data”.) CE to D5 Fixed data-1
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C, D6 Fixed data-2
18, 1C Page Data”). D7 Fixed data-1
D8 Fixed data-2
Address Remark
D9 to DA Fixed data-1
00 to 18 Fixed data-1 DB Fixed data-2
19 Fixed data-2 DC (Modified data. Copy the data
1A to 29 Fixed data-1 DD built in the same model.)
2A Fixed data-2 DE
2B to 34 Fixed data-1 DF
34 Fixed data-2 E0
35 to 3F Fixed data-1 E1 to E2 Fixed data-1
40 Fixed data-2 E3 Fixed data-2
41 to 79 Fixed data-1 E4 (Modified data. Copy the data
7A Fixed data-2 E5 built in the same model.)
7B (Modified data. Copy the data E6
7C built in the same model.) E7 Fixed data-1
7D to 81 Fixed data-1 E8 Fixed data-2
82 Fixed data-2 E9 to EA Fixed data-1
83 Fixed data-1 EB Fixed data-2
84 Fixed data-2 EC (Modified data. Copy the data
85 to 86 Fixed data-1 ED built in the same model.)
87 Fixed data-2 EE
88 (Modified data. Copy the data EF to FF Fixed data-1
89 built in the same model.) Table. 6-1-6.
8A
8B
8C to 91 Fixed data-1
92 Fixed data-2
93 to 94 Fixed data-1
95 Fixed data-2
96 to AC Fixed data-1
AD Fixed data-2
AE to B0 Fixed data-1
B1 Fixed data-2
B2 to B5 Fixed data-1
B6 Fixed data-2
B7 Fixed data-1
B8 Fixed data-2
B9 Fixed data-1
BA Fixed data-2
BB
BC to BD Fixed data-1
BE Fixed data-2
BF
C0 to C3 Fixed data-1
C4 Fixed data-2
C5
C6 to C7 Fixed data-1
C8 Fixed data-2
C9 (Modified data. Copy the data
CA built in the same model.)
CB Fixed data-1
CC Fixed data-2
CD
6-15
DCR-TRV60/TRV60E/TRV70
4. C Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Address Initial value Remark
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C,
18, 1C Page Data”.) NTSC PAL
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C, 5C Fixed data-2
18, 1C Page Data”). 5D
5E Fixed data-1
Address Initial value Remark 5F Fixed data-2
NTSC PAL 60 (Modified data. Copy the data
00 to 0F 61 built in the same model.)
10 EE EE Switching position adj. 62
11 00 00 63
12 00 00 64
13 00 00 65
14 to 15 Fixed data-1 66
16 E0 E0 CAP FG duty adj. 67
17 to 24 Fixed data-1 68
25 5D 5D S VIDEO out Y level adj. 69
26 7D 7D S VIDEO out Cr level adj. 6A
27 59 59 S VIDEO out Cb level adj. 6B
28 to 33 Fixed data-1 6C
34 Fixed data-2 6D
35 6E to 9B Fixed data-1
36 59 78 VCO adj. (EVF) 9C Fixed data-2
37 71 60 9D to A3 Fixed data-1
38 Fixed data-2 A4 Fixed data-2
39 8A 87 RGB AMP adj. (EVF) A5 to CB Fixed data-1
3A to 3B Fixed data-1 CC Fixed data-2
3C 8D 8D White balance adj. (EVF) CD (Modified data. Copy the data
3D 73 73 CE built in the same model.)
3E 35 35 Contrast adj. (EVF) CF
3F Fixed data-1 D0
40 Fixed data-2 D1
41 (Modified data. Copy the data D2
42 built in the same model.) D3
43 D4
44 D5 to DE Fixed data-1
45 DF Fixed data-2
46 E0 08 08 Serial No. input
47 6A 6A VCO adj. (LCD) E1 00 00
48 93 93 E2 46 46
49 A2 A2 V COM adj. (LCD) E3 01 01
4A A3 A3 RGB AMP adj. (LCD) E4 02 02
4B Fixed data-2 E5 00 00
4C E6 00 00
4D 7D 7D White balance adj. (LCD) E7 00 00
4E 65 65 E8 to F3 Fixed data-1
4F 40 40 Contrast adj. (LCD) F4 00 00 Emergency memory address
50 Fixed data-2 F5 00 00
51 F6 00 00
52 C0 C0 PSIG black adj. (LCD) F7 00 00
53 Fixed data-2 F8 00 00
54 (Modified data. Copy the data F9 00 00
55 built in the same model.) FA 00 00
56 FB 00 00
57 FC 00 00
58 FD 00 00
59 FE 00 00
5A FF 00 00
5B Fixed data-1
Table. 6-1-7.
6-16
DCR-TRV60/TRV60E/TRV70
6-17
DCR-TRV60/TRV60E/TRV70
6-18
DCR-TRV60/TRV60E/TRV70
3. E Page Table
Note1: The data of page: 0, address: 10 must be “00”. Address Remark
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F,
1E, 1F Page Data”.) 5B Fixed data-2
Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 5C to 65 Fixed data-1
1E, 1F Page Data”). 66 Fixed data-2
67 (Modified data. Copy the data
Address Remark 68 built in the same model.)
00 to 04 Fixed data-1 69
05 Fixed data-2 6A to 6E Fixed data-1
06 to 07 Fixed data-1 6F Fixed data-2
08 Fixed data-2 70
09 (Modified data. Copy the data 71 to B1 Fixed data-1
0A built in the same model.) B2 Fixed data-2
0B B3 to BC Fixed data-1
0C Fixed data-1 BD Fixed data-2
0D Fixed data-2 BE to ED Fixed data-1
0E EE Fixed data-2
0F Fixed data-1 EF Fixed data-1
10 Fixed data-2 F0 Fixed data-2
11 to 1F Fixed data-1 F1 (Modified data. Copy the data
20 Fixed data-2 F2 built in the same model.)
21 (Modified data. Copy the data F3
22 built in the same model.) F4
23 F5
24 F6
25 F7
26 F8
27 F9
28 to 2F Fixed data-1 FA to FF Fixed data-1
30 Fixed data-2 Table. 6-1-10.
31
32 to 37 Fixed data-1
38 Fixed data-2
39
3A to 3D Fixed data-1
3E Fixed data-2
3F
40 to 43 Fixed data-1
44 Fixed data-2
45
46 Fixed data-1
47 Fixed data-2
48 (Modified data. Copy the data
49 built in the same model.)
4A
4B
4C
4D
4E
4F
50
51
52 Fixed data-1
53 Fixed data-2
54
55
56 to 5A Fixed data-1
6-19
DCR-TRV60/TRV60E/TRV70
4. F Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Address Initial value Remark
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F,
1E, 1F Page Data”.) NTSC PAL
Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 4D 54 54 Flange back adj.
1E, 1F Page Data”). 4E 00 00
4F 00 00
Address Initial value Remark 50 00 00
NTSC PAL 51 00 00
00 to 0F 52 6E 6E
10 40 40 54MHz/67.5MHz origin osc. adj. 53 19 19
11 to 12 Fixed data-1 54 19 19
13 39 39 HALL adj. 55 32 32
14 80 80 56 00 00
15 88 88 57 06 06
16 47 47 58 00 00
17 81 81 59 Fixed data-1
18 88 88 5A 80 80 MR adj.
19 C9 D8 MAX GAIN adj. 5B 80 80
1A 77 75 LV standard data input 5C 80 80
1B 93 93 5D 80 80
1C to 23 Fixed data-1 5E 40 40
24 00 00 CCD output 2ch matching adj. (1) 5F C0 C0
25 00 00 60 40 40
26 00 00 61 C0 C0
27 00 00 62 40 40
28 Fixed data-1 63 C0 C0
29 00 00 CCD output 2ch matching adj. (2) 64 40 40
2A 00 00 65 C0 C0
2B 00 00 66 20 20 AF laser output adj.
2C 00 00 67 00 00
2D 00 00 68 00 00
2E 18 18 AWB standard data input 69 00 00
2F 06 06 6A 00 00
30 08 08 6B 00 00
31 C7 C7 6C 00 00
32 0F 0F Auto white balance adj. 6C to 71 Fixed data-1
33 5D 5D 72 Fixed data-2
34 10 10 73
35 76 76 74 to 75 Fixed data-1
36 Fixed data-1 76 40 40 Mechanical shutter adj.
37 41 41 Color reproduction adj. 77 00 00
38 Fixed data-1 78 34 34
39 2D 2D Color reproduction adj. 79 00 00
3A to 3D Fixed data-1 7A 30 30
3E 2D 2D Strobe white balance adj. 7B 00 00
3F 64 64 7C 2A 2A
40 02 02 Color reproduction adj. 7D 00 00
41 DE DE 7E 1B 16
42 to 44 Fixed data-1 7F 00 00
45 Fixed data-2 80 40 40
46 Fixed data-1 81 3A 3A
47 Fixed data-2 82 31 31
48 4E 4E Flange back adj. 83 31 31
49 BE BE 84 35 35
4A 4D 4D 85 1E 1E
4B 69 69 86 80 80
4C 1E 1E 87 80 80
6-20
DCR-TRV60/TRV60E/TRV70
F page
5. 1E Page Table
Note1: When reading or writing the 1E page data, select page: 0, address: 10,
Address Initial value Remark
and set data: 01, then select E page. The 1E page can be chosen by
NTSC PAL this data setting.
88 80 80 Mechanical shutter adj. After reading or writing, reset the data of page: 0, address: 10 to “00”.
89 80 80 Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F,
1E, 1F Page Data”.)
8A 80 80 Fixed data-2: Modified data. (Refer to “2. Modification of E, F,
8B 80 80 1E, 1F Page Data”).
8C 01 01 Strobe light level adj.
8D E0 E0 Address Remark
8E 80 80 00 to 91 Fixed data-1
8F 80 80 92 Fixed data-2
90 80 80 93 to C3 Fixed data-1
91 20 20 C4 Fixed data-2
92 19 19 Hall adj. C5
93 to 97 Fixed data-1 C6 Fixed data-1
98 Fixed data-2 C7 Fixed data-2
97 to AA Fixed data-1 C9 Fixed data-1
AB Fixed data-2 C9 Fixed data-2
AC to AF Fixed data-1 CA (Modified data. Copy the data
B0 Fixed data-2 CB built in the same model.)
B1 CC
B2 to CC Fixed data-1 CD
CD Fixed data-2 CE
CE (Modified data. Copy the data CF Fixed data-1
CF built in the same model.) D0 Fixed data-2
D0 D1
D1 to F7 Fixed data-1 D2 to FF Fixed data-1
F8 Fixed data-2 Table. 6-1-12.
F9
FA to FF Fixed data-1
Table. 6-1-11.
6-21
DCR-TRV60/TRV60E/TRV70
6. 1F Page Table
Note1: When reading or writing the 1F page data, select page: 0, address: Address Remark
10, and set data: 01, then select F page. The 1F page can be chosen
by this data setting. F3 Fixed data-2
After reading or writing, reset the data of page: 0, address: 10 to F4 to FC Fixed data-1
“00”. FD Fixed data-2
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F,
1E, 1F Page Data”.) FE to FF Fixed data-1
Fixed data-2: Modified data. (Refer to “2. Modification of E, F, Table. 6-1-13.
1E, 1F Page Data”).
Address Remark
00 Fixed data-2
01 to 35 Fixed data-1
36 Fixed data-2
37 Fixed data-1
38 Fixed data-2
39 to 3D Fixed data-1
3E Fixed data-2
3F to 44 Fixed data-1
45 Fixed data-2
46
47 to 57 Fixed data-1
58 Fixed data-2
59 to 5B Fixed data-1
5C Fixed data-2
5D to 6F Fixed data-1
70 Fixed data-2
71
72 to 7A Fixed data-1
7B Fixed data-2
7C to 8D Fixed data-1
8E Fixed data-2
8F to 93 Fixed data-1
94 Fixed data-2
95 (Modified data. Copy the data
96 built in the same model.)
97
98
99 to AB Fixed data-1
AC Fixed data-2
AD
AE Fixed data-1
AF Fixed data-2
B0 Fixed data-1
B1 Fixed data-2
B2
B3 to B9 Fixed data-1
BA Fixed data-2
BB
BC to C9 Fixed data-1
CA Fixed data-2
CB (Modified data. Copy the data
CC built in the same model.)
CD
CE to E4 Fixed data-1
E5 Fixed data-2
E6 to F2 Fixed data-1
6-22
DCR-TRV60/TRV60E/TRV70
COVER
Switch setting:
1) POWER .................................................................. CAMERA
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 01 BD Set the data, and press PAUSE
button.
3 6 02 Check that the data changes to
“01”. (Note5)
4 F 5A Check that the data satisfies the
specified value 1.
5 F 5B Check that the data satisfies the
specified value 1.
6 F 5C Check that the data satisfies the
specified value 1.
7 F 5D Check that the data satisfies the
specified value 1.
8 F 5E Check that the data satisfies the
specified value 2.
9 F 5F Check that the data satisfies the
specified value 3.
10 F 60 Check that the data satisfies the
specified value 2.
11 F 61 Check that the data satisfies the
specified value 3.
12 F 62 Check that the data satisfies the
specified value 2.
13 F 63 Check that the data satisfies the
specified value 3.
14 F 64 Check that the data satisfies the
specified value 2.
15 F 65 Check that the data satisfies the
specified value 3.
6-24
DCR-TRV60/TRV60E/TRV70
4. CCD Output 2ch Matching Adjustment (1) 5. CCD Output 2ch Matching Adjustment (2)
Correct the dispersion of the black level between the left-right Correct the dispersion between the left-right channels of the CCD
channels of the CCD imager. imager.
Subject Arbitrary Subject Clear chart (All white) (Note1)
Adjustment Page F Adjustment Page F
Adjustment Address 24 to 27 Adjustment Address 29 to 2D
Note1: This adjustment should be carried out upon completion of the Note1: Shoot the clear chart with the zoom TELE end.
following adjustments. Note2: This adjustment should be carried out upon completion of the
“HALL Adjustment” following adjustments.
Note2: The data of page: 0, address: 10 must be “00”. CCD Output 2ch Matching adjustment (1)
Note3: Check that the data of page: 6, address: 02 is “00”. If not, to page: Note3: The data of page: 0, address: 10 must be “00”.
6, address: 01, set data: 00, and press the PAUSE button. Note4: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1) POWER .................................................................. CAMERA Switch setting:
2) NIGHT SHOT .................................................................. OFF 1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Adjusting method: 3) ZOOM .................................................................... TELE end
Order Page Address Data Procedure
Adjusting method:
1 0 01 01 Set the data.
Order Page Address Data Procedure
2 6 01 F3 Set the data, and press PAUSE
button. 1 0 01 01 Set the data.
3 6 02 Check that the data changes to 2 6 2C 01 Set the data.
“01”. (Note4) 3 6 40 01 Set the data.
4 6 01 F5 Set the data, and press PAUSE
Note4: The adjustment data will be automatically input to page: F, address: button.
24 to 27.
5 6 02 Check that the data changes to
Processing after Completing Adjustments “00” in about 50 seconds after
pressing PAUSE button.
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSE Note5: The adjustment data will be automatically input to page: F, address:
button. 29 to 2D
2 Perform “CCD Output 2ch
Matching Adjustment (2)”. Processing after Completing Adjustments
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSE
button.
2 6 2C 00 Set the data.
3 6 40 00 Set the data.
4 0 01 00 Set the data.
6-25
DCR-TRV60/TRV60E/TRV70
6-26
DCR-TRV60/TRV60E/TRV70
7-1. Flange Back Adjustment (1) 7-2. Flange Back Adjustment (2)
Subject Flange back adjustment chart Perform this adjustment after performing “Flange Back Adjustment
(2.0 m from the front of the protection (1)”.
glass) (Luminance: 350 ± 50 lux) Subject Subject more than 500m away
Measurement Point Adjustment remote commander (Subjects with clear contrast such as
buildings, etc.)
Measuring Instrument
Measurement Point Check operation on TV monitor
Adjustment Page F
Measuring Instrument
Adjustment Address 48 to 58
Adjustment Page F
Specified Value Data of page: F, address: 57 is “00” to
“09”. Adjustment Address 48 to 58
Note1: This adjustment should be carried out upon completion of the Note1: Make the lens horizontal and perform this adjustment.
following adjustments. Note2: The data of page: 0, address: 10 must be “00”.
“HALL Adjustment”, “MR Adjustment” Note3: Check that the data of page: 6, address: 02 is “00”. If not, turn off
“CCD Output 2ch Matching Adjustment” the power and turn on again.
Note2: Make the lens horizontal and perform this adjustment.
Note3: The data of page: 0, address: 10 must be “00”. Switch setting:
Note4: Check that the data of page: 6, address: 02 is “00”. If not, turn off 1) POWER .................................................................. CAMERA
the power and turn on again. 2) NIGHT SHOT .................................................................. OFF
3) COLOR SLOW SHUTTER (Function setting) ............... OFF
Switch setting:
1) POWER .................................................................. CAMERA Preparations:
2) NIGHT SHOT .................................................................. OFF 1) Set the zoom lens to the TELE end and expose a subject that is
3) COLOR SLOW SHUTTER (Function setting) ............... OFF more than 500m away (subject with clear contrast such as
building, etc.). (Nearby subjects less than 500m away should
Preparations: not be in the screen.)
1) Check that at both the zoom lens TELE end and WIDE end,
the center of the chart for the flange back adjustment and center Adjusting method:
of the exposure screen coincide. Order Page Address Data Procedure
Adjusting method: 1 0 01 01 Set the data.
Order Page Address Data Procedure 2 6 01 13 Set the data, and press PAUSE
button. (Note2)
1 0 01 01 Set the data.
3 Place a ND filter on the lens so
2 6 01 13 Set the data, and press PAUSE that the optimum image is obtain.
button. (Note2)
4 6 01 29 Set the data, and press PAUSE
3 6 01 15 Set the data, and press PAUSE button.
button.
5 6 02 Check that the data changes to
4 6 02 Check that the data changes to “01”. (Note4)
“01”. (Note5)
5 F 57 Check the data is “00” to “09”. Note4: The adjustment data will be automatically input to page: F, address:
48 to 58.
Note5: The adjustment data will be automatically input to page: F, address:
48 to 58. Processing after Completing Adjustments:
Order Page Address Data Procedure
Processing after Completing Adjustments:
1 6 01 00 Set the data, and press PAUSE
Order Page Address Data Procedure button.
1 6 01 00 Set the data, and press PAUSE 2 6 01 25 Set the data, and press PAUSE
button. button.
2 6 01 25 Set the data, and press PAUSE 3 6 01 00 Set the data, and press PAUSE
button. button.
3 6 01 00 Set the data, and press PAUSE 4 0 01 00 Set the data.
button.
5 Perform “Data Setting during
4 0 01 00 Set the data. the Following Camera System
5 Perform “Flange Back Adjustments”. (Note5)
Adjustment (2)” 6 Perform “Flange Back Check”
6-27
DCR-TRV60/TRV60E/TRV70
Note1: Shoot the clear chart with the zoom WIDE end. And adjust the
Note1: The data of page: 0, address: 10 must be “00”.
direction of the camera so that the chart is located in the center of
the screen.
Switch setting: Note2: The data of page: 0, address: 10 must be “00”.
1) POWER .................................................................. CAMERA Note3: This adjustment should be carried out upon completion of “Flange
2) NIGHT ............................................................................. OFF Back Adjustment”.
Note4: NTSC model: DCR-TRV60/TRV70
Note2: When the auto focus is ON, the lens can be checked if it is focused PAL model: DCR-TRV60E
or not by observing the data on the page 1 of the adjustment remote
commander. Switch setting:
1) Select page: 0, address: 03, and set data: 0F. 1) POWER .................................................................. CAMERA
2) Page 1 shows the state of the focus. 2) NIGHT SHOT .................................................................. OFF
1 : 00 : XX
3) ZOOM .................................................................... WIDE end
Odd: Focused
Even: Unfocused
4) DIGITAL ZOOM (Menu setting) .................................... OFF
6-28
DCR-TRV60/TRV60E/TRV70
Setting method:
1) Adjust the zoom and the camera direction, and set to the
specified position.
2) Mark the position of the picture frame on the monitor display,
and adjust the picture frame to this position in following
adjustments using “Color reproduction adjustment frame”.
Fig. 6-1-11.
2. Vertical period
E E=F F
Fig. 6-1-12.
6-29
DCR-TRV60/TRV60E/TRV70
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
3) FOCUS .................................................................. MANUAL
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 9D, and set data: 20.
3) Select page: 6, address: 01, set data: 3D, and press the PAUSE Burst position
button.
4) Select page: F, address: F0, set the following data, and press
the PAUSE button.
37 (NTSC), B7 (PAL)
5) Adjust the GAIN and PHASE of the vectorscope, and adjust
For PAL model
the burst luminance point to the burst position of the color
reproduction frame.
Burst position
6) Change the data of page: F, address: 37, 39, 40 and 41, and
settle each color luminance point in each color reproduction
frame.
Note: Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new data
will not be written to the memory.
Fig. 6-1-14.
6-30
DCR-TRV60/TRV60E/TRV70
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
3) FOCUS .................................................................. MANUAL
4) DIGITAL ZOOM (Menu setting) .................................... OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 Wait for more than 6 sec.
3 6 40 01 Set the data, and press PAUSE
button.
4 6 01 0D Set the data, and press PAUSE
button.
5 6 02 Check that the data changes to
“01”. (Note5)
6 0 03 1E Set the data.
7 1 Check that the display data (Note5)
satisfies the specified value.
6-31
DCR-TRV60/TRV60E/TRV70
13. Picture Frame Setting (All White Frame) 14. Auto White Balance Standard Data Input
When performing “Auto White Balance Standard Data Input”, “Auto Adjust the white balance reference at 3200K.
White Balance Adjustment” and “White Balance Check”, set the Subject Clear chart (All white frame) (Note4)
picture frame to “All white frame”.
Adjustment Page F
Subject Clear chart (All white frame)
Adjustment Address 2E to 31
(1.5m from the front of the lens)
Measurement Point Video terminal of AUDIO/VIDEO jack Note1: This adjustment should be carried out upon completion of “Color
Measuring Instrument TV monitor (Under scan mode) Reproduction Adjustment”.
Note2: The data of page: 0, address: 10 must be “00”.
Specified Value Whole of the screen is white Note3: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Note: The data of page: 0, address: 10 must be “00”. Note4: Perform “13. Picture Frame Setting (All White Frame)” before
this adjustment.
Switch setting:
1) POWER .................................................................. CAMERA Switch setting:
2) NIGHT SHOT .................................................................. OFF 1) POWER .................................................................. CAMERA
3) FOCUS .................................................................. MANUAL 2) NIGHT SHOT .................................................................. OFF
4) DIGITAL ZOOM (Menu setting) .................................... OFF 3) FOCUS .................................................................. MANUAL
5) STEADY SHOT (Menu setting) ...................................... OFF 4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ...................................... OFF
Setting method:
Order Page Address Data Procedure Adjusting method:
1 6 90 CD Set the data. Order Page Address Data Procedure
2 6 91 02 Set the data. 1 Check that the whole of the
3 6 92 C7 Set the data. screen is white. If not, perform
“13. Picture Frame Setting (All
4 6 93 31 Set the data. White Frame)”.
5 6 01 79 Set the data, and press PAUSE 2 0 01 01 Set the data.
button.
3 Wait for more than 2 sec.
6 Check that the whole of the
4 6 01 11 Set the data, and press PAUSE
screen is white.
button.
7 Perform the following
adjustments. 5 6 01 0B Set the data, and press PAUSE
button.
Processing after Completing Adjustments 6 6 02 Check that the data changes to
After completing “Auto White Balance Standard Data Input”, “Auto “01”. (Note5)
White Balance Adjustment” and “White Balance Check”, release 7 Perform “Auto White Balance
the data setting. Adjustment”.
Order Page Address Data Procedure
1 6 90 00 Set the data. Note5: The adjustment data will be automatically input to page: F, address:
2E to 31.
2 6 91 00 Set the data.
3 6 92 00 Set the data.
4 6 93 00 Set the data.
6-32
DCR-TRV60/TRV60E/TRV70
6-33
DCR-TRV60/TRV60E/TRV70
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
3) FOCUS .................................................................. MANUAL
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ...................................... OFF
Checking method:
Order Page Address Data Procedure R-Y 2mm
6-34
DCR-TRV60/TRV60E/TRV70
6-35
DCR-TRV60/TRV60E/TRV70
19. Strobe Light Level Adjustment 20. Strobe White Balance Adjustment & Check
Adjust the light level when the strobe light flashes. Adjust and check the white balance when the strobe light flashes.
Subject Paper which reflection rate is 18% Subject Paper which reflection rate is 18%
(50cm from the front of the lens)(Note1) (50cm from the front of the lens)(Note1)
Measurement Point Adjustment remote commander Measurement Point Video terminal of AUDIO/VIDEO jack
Measuring Instrument Measuring Instrument Vectorscope
Adjustment Page F Adjustment Page F
Adjustment Address 8C to 91 Adjustment Address 3E, 3F
Specified Value Data of page: 6, address: B8 is “00”. Specified Value Fig. 6-1-16.
Note1: Background paper (J-250-130-A). Perform this adjustment in the Note1: Background paper (J-250-130-A). Perform this adjustment in the dark
dark room or use the flash adjustment box. (Refer to “1-1- room or use the flash adjustment box. (Refer to “1-1-3.Precaution”.)
3.Precaution”.) Note2: Any light other than the strobe light should not light up the paper.
Note2: Any light other than the strobe light should not light up the paper. Note3: This adjustment should be carried out upon completion of “HALL
Note3: This adjustment should be carried out upon completion of “HALL Adjustment”, “Flange Back Adjustment”, , “Auto White Balance
Adjustment”, “Flange Back Adjustment”. Adjustment”, “Strobe Light Level Adjustment”
Note4: The data of page: 0, address: 10 must be “00”. Note4: After the power is turned on, this adjustment can be done only once.
Note5: Check that the data of page: 6, address: 02 is “00”. If not, to page: Note5: The data of page: 0, address: 10 must be “00”.
6, address: 01, set data: 00, and press the PAUSE button. Note6: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1) POWER .................................................................. CAMERA Switch setting:
2) FLASH ......................................................................... OPEN 1) POWER .................................................................. CAMERA
(Press FLASH ( ) button and set to the forced flash mode ( ), 2) FLASH ......................................................................... OPEN
and press PHOTO button.) (Press FLASH ( ) button and set to the forced flash mode
3) NIGHT SHOT .................................................................. OFF ( ), and press PHOTO button.)
3) NIGHT SHOT .................................................................. OFF
Adjusting method:
Order Page Address Data Procedure Adjusting method:
1 0 01 01 Set the data. Order Page Address Data Procedure
2 7 05 04 Set the data. (Note6) 1 0 01 01 Set the data.
3 6 01 67 Set the data, and press PAUSE 2 7 05 04 Set the data. (Note7)
button. 3 6 01 B9 Set the data, and press PAUSE
4 Check the flashing. button.
5 6 02 Check that the data is “01”. 4 Check the flashing.
(Note7) 5 6 02 Check that the data is “01”.
6 6 B8 Check that the data is “00”. (Note8)
6 6 01 00 Set the data and press PAUSE
Note6: Use the STOP button of the adjustment remote commander.
Note7: The adjustment data will be automatically input to page: F, address: button.
8C to 91. 7 6 01 E7 Set the data, and press PAUSE
button.
Processing after Completing Adjustments: 8 Check the flashing.
Order Page Address Data Procedure 9 Wait for 3 sec.
1 6 01 00 Set the data, and press PAUSE 10 Check that the center of the
button. white luminance point is within
2 7 05 00 Set the data. the circle shown Fig. 6-1-16.
3 0 01 00 Set the data.
Note7: Use the STOP button of the adjustment remote commander.
Note8: The adjustment data will be automatically input to page: F, address:
3E, 3F.
R-Y 2mm
Processing after Completing Adjustments:
Order Page Address Data Procedure
B-Y 1 6 01 00 Set the data, and press PAUSE
button.
2 7 05 00 Set the data.
2mm
3 0 01 00 Set the data.
Fig. 6-1-16.
6-36
DCR-TRV60/TRV60E/TRV70
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 01 AF Set the data, and press PAUSE
button.
3 Check the laser light is output.
4 6 02 Check that the data is “01”.
(Note5)
5 F 66 Check that the data is “10” to
“FF”.
6 F 67 Check that the data is “00” to
“58”.
7 F 68 Check that the data is “0A” to
“FF”.
8 F 6B Check that the data is “37” to
“53”.
6-37
DCR-TRV60/TRV60E/TRV70
Checking method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 E EF 82 Set the data.
3 6 23 04 Set the data.
4 6 5B B4 Set the data.
5 6 5C B4 Set the data. Fig. 6-1-14.
6 6 66 00 Set the data.
7 6 67 00 Set the data.
8 6 90 DB Set the data.
9 6 91 02 Set the data.
10 6 92 C0 Set the data.
11 6 93 46 Set the data.
12 6 01 79 Set the data, and press PAUSE
button.
13 6 01 78 Set the data, and press PAUSE
button.
14 Check that two or more
hologram lines are perfectly
within the inspection frame.
(Fig. 6-1-14.)
15 Check that the hologram lines
can be seen at every outside of
the inspection frame on the
monitor TV screen (the top, the
bottom, the left and the right).
(Fig. 6-1-14.)
6-38
DCR-TRV60/TRV60E/TRV70
Switch setting:
1) POWER ................................................................. MEMORY
2) NIGHT SHOT .................................................................. OFF
3) FOCUS .................................................................. MANUAL
Inspection frame
Checking method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 E EF 82 Set the data.
3 6 23 04 Set the data.
4 6 5B A6 Set the data.
5 6 5C A6 Set the data.
6 6 66 07 Set the data.
7 6 67 08 Set the data.
8 6 90 AB Set the data. Fig. 6-1-15.
9 6 91 01 Set the data.
10 6 92 F0 Set the data.
11 6 93 57 Set the data.
12 6 01 79 Set the data, and press PAUSE
button.
13 6 01 78 Set the data, and press PAUSE
button.
14 Check that two or more
hologram lines are perfectly
within the inspection frame.
(Fig. 6-1-15.)
15 Check that the hologram lines
can be seen at every outside of
the inspection frame on the
monitor TV screen (the top, the
bottom, the left and the right).
(Fig. 6-1-15.)
6-39
DCR-TRV60/TRV60E/TRV70
COVER
6-40
DCR-TRV60/TRV60E/TRV70
6-41
DCR-TRV60/TRV60E/TRV70
2H
Pedestal
Fig. 6-1-17.
6-42
DCR-TRV60/TRV60E/TRV70
100 IRE
2H
Pedestal
Fig. 6-1-18.
6-43
DCR-TRV60/TRV60E/TRV70
Note1: Check the white balance only when replacing the following parts.
If necessary, adjust them.
1. LCD panel
2. Light induction plate
3. IC3201
Note2: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 3C 8D Set the data, and press PAUSE
button.
3 C 3D 73 Set the data, and press PAUSE
button.
4 C 3D Check that the EVF screen is not
colored. If not colored, proceed to
step 10.
5 C 3C Change the data so that the EVF
screen is not colored.
6 C 3C Press PAUSE button.
7 C 3D Change the data so that the EVF
screen is not colored.
8 C 3D Press PAUSE button.
9 C 3D If the EVF screen is colored,
repeat steps 5 to 9.
10 0 01 00 Set the data.
6-44
DCR-TRV60/TRV60E/TRV70
COVER
6-45
DCR-TRV60/TRV60E/TRV70
6-46
DCR-TRV60/TRV60E/TRV70
Fig. 6-1-20.
6-47
DCR-TRV60/TRV60E/TRV70
COVER
CH1
CH2
(Trigger)
3.3 msec
Fig. 6-2-1.
6-48
DCR-TRV60/TRV60E/TRV70
COVER
1) TV monitor
2) Oscilloscope (dual-phenomenon, band width above 30 MHz
with delay mode) (Unless specified otherwise, use a 10 : 1
probe.)
3) Frequency counter
4) Pattern generator with video output terminal
5) Digital voltmeter
6) Audio generator
7) Audio level meter
8) Audio distortion meter
9) Audio attenuator
10) Regulated power supply
11) Alignment tapes
• Tracking standard (XH2-1)
Parts code: 8-967-997-01
• SW/OL standard (XH2-3)
Parts code: 8-967-997-11
• Audio operation check for NTSC (XH5-3)
Parts code: 8-967-997-51
• System operation check for NTSC (XH5-5)
Parts code: 8-967-997-61
• Audio operation check for PAL (XH5-3P)
Parts code: 8-967-997-55
• System operation check for PAL (XH5-5P)
Parts code: 8-967-997-66
12) Adjustment remote commander (J-6082-053-B)
13) CPC-7 jig (J-6082-382-A)
14) Extension cable (100P 0.5mm) (J-6082-352-A)
For extension between the DI-088 board (CN4003) and the
VC-314 board (CN1003)
6-49
DCR-TRV60/TRV60E/TRV70
3-1-2. Precautions on Adjusting Note2: Setting the “Forced VTR Power ON” mode (VTR mode)
Note1: Before performing the adjustments, check the data of page: 0, 1) Select page: 0, address: 01, and set data: 01.
address: 10 is “00”. If not, set data: 00 to this address. 2) Select page: D, address: 10, set data: 02, and press the PAUSE
1) The adjustments of this unit are performed in the VTR mode button of the adjusting remote commander.
or camera mode. The above procedure will enable the VTR power to be turned
on with the control switch block (FK-4110 block) removed.
To set to the VTR mode, set the power switch to “VCR” or set
After completing adjustments, be sure to exit the “Forced Power
the “Forced VTR Power ON mode” using the adjusting remote ON mode”.
commander (Note2). Note3: Setting the “Forced Camera Power ON” mode (Camera mode)
To set to the Camera mode, set the power switch to “CAMERA” 1) Select page: 0, address: 01, and set data: 01.
or set the “Forced Camera Power ON mode” using the adjusting 2) Select page: D, address: 10, set data: 01, and press the PAUSE
remote commander (Note3). button of the adjusting remote commander.
After completing adjustments, be sure to exit the “Forced VTR The above procedure will enable the camera power to be turned
Power ON Mode” or “Forced Camera Power ON Mode”. on with the control switch block (FK-4110 block) removed.
After completing adjustments, be sure to exit the “Forced Power
(Note5)
ON mode”.
2) Cabinet (R) (CK-130 board, LCD block) need not be connected. Note4: Setting the “Forced Memory Power ON” mode (Memory mode)
To remove it, disconnect the following connector. 1) Select page: 0, address: 01, and set data: 01.
VC-314 board CN1007 (39P, 0.3mm) 2) Select page: D, address: 10, set data: 05, and press the PAUSE
3) Short-circuit between (+) and (–) terminal of the capacitor button of the adjusting remote commander.
(C001) of the flash unit (FL4110) with the short jig about 10 The above procedure will enable the memory power to be turned
seconds and discharge the capacitor. (Refer to “SERVICE on with the control switch block (FK-4110 block) removed.
NOTE”.) After completing adjustments, be sure to exit the “Forced Power
ON mode”.
4) The battery terminal is need not be connected. To remove it,
Note5: Exiting the “Forced Power ON” mode
disconnect the following connector. 1) Select page: 0, address: 01, and set data: 01.
DI-088 board CN4202 (3P, 1.5mm) 2) Select page: D, address: 10, set data: 00, and press the PAUSE
5) The EVF block (LB-086 board) is need not be connected. To button of the adjusting remote commander.
remove it, disconnect the following connector. 3) Select page: 0, address: 01, and set data: 00.
DI-088 board CN3201 (16P, 0.5mm)
6) The flash unit (FL4110) is need not be connected. To remove
it, disconnect the following connector.
DI-088 board CN4001 (39P, 0.3mm)
7) The intelligent accessory shoe is need not be connected. To
remove it, disconnect the following connector.
DI-088 board CN4002 (10P, 0.5mm)
8) Removing the DI-088 board means removing the lithium 3V
power supply (DI-088 board, BT4001), data such as date, time,
user-set menus will be lost. After completing adjustments, reset
these data.
But, the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the DI-088 board
has been removed. (Refer to “6-4.Service Mode” for the data
on the history use and the self-diagnosis data.)
To open the DI-088 board, use the following extension cable
between the DI-088 board CN4003 and VC-314 board CN1003.
J-6082-352-A (100P, 0.5mm)
9) By setting the “Forced VTR Power ON mode”, the video section
can be operate even if the control switch block (FK-4110) has
been removed. When removing it, disconnect the following
connector.
VC-314 board CN1006 (27P, 0.3mm)
10) The JK-245 board (DV jack, USB jack) is need not be
connected. To remove it, disconnect the following connectors.
VC-314 board CN1002 (14P, 0.5mm)
11) The microphone unit is need not be connected. To remove it,
disconnect the following connectors.
VC-314 board CN1001 (4P, 1.0mm)
12) As the timing generator (IC7501) is provided on the CD-433
board of the lens block, the CN1101 of CD-433 board and
CN1500 of VC-314 board must be connected when performing
adjustments.
6-50
DCR-TRV60/TRV60E/TRV70
TV monitor
VIDEO
(Yellow)
Main unit
AUDIO L (White)
Adjustment
remote
commander
AUDIO R (Red)
LANC jack AUDIO/VIDEO jack
Fig. 6-3-2.
6-51
DCR-TRV60/TRV60E/TRV70
Fig. 6-3-3 shows the 75% color bar signals recorded on the alignment
tape for Audio Operation Check.
Cyan
Magenta
Green
White (75%)
Magenta
Red
White
Blue
Burst signal
Yellow
Green
Cyan
Red
Blue
0.714V
(75%)
1V
0.286V
0.286V Q I Black
Q I
White
(100%)
Horizontal sync signal
Color bar signal waveform Color bar pattern
Green
Cyan
Magenta
Red
Blue
0.7V
Magenta
Green
Yellow
1V
Cyan
White
Red
Blue
Black
0.3V
0.3V (100%)
Burst signal
Horizontal sync signal
6-52
DCR-TRV60/TRV60E/TRV70
COVER
Address Data
E0 08
E1 00
E2 46
E3 01
E4 02
3) Select page: 0, address: 01, and set data: 00.
6-53
DCR-TRV60/TRV60E/TRV70
6-54
DCR-TRV60/TRV60E/TRV70
COVER
3-3. SERVO AND RF SYSTEM ADJUSTMENT 2. Switching Position Adjustment (VC-314 Board)
Before perform the servo and RF system adjustments, check that
the specified value of “54 MHz/67.5 MHz Origin Oscillation To obtain normal playback waveform output during the playback
Adjustment” of “CAMERA SYSTEM ADJUSTMENT” is satisfied. mode, adjust the switching position.
And check that the data of page: 0, address: 10 is “00”. If not, set Mode VTR playback
data: 00 to this address. Signal SW/OL reference tape (XH2-3)
Note: The lens block (CD-433 board) must be connected when performing Measurement Point Display data of page: 3, address: 02, 03
the adjustments. Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjusting Procedure:
1. CAP FG duty adjustment Adjustment Address 10, 11, 12, 13
2. Switching position adjustment Specified Value Data of page: 3, address: 02 is “00”.
3. Error rate check Data of page: 3, address: 03 is “00”.
1. Cap FG Duty Adjustment (VC-314 Board) Note1: The data of page: 0, address: 10 must be “00”.
Set the Cap FG signal duty cycle to 50% to establish an appropriate
capstan servo. If deviated, the uneven rotation of capstan and noise Adjusting method:
can occur. Order Page Address Data Procedure
Measurement Point Display data of page: 3, address: 02, 03 1 Insert the SW/OL reference tape
Measuring Instrument Adjustment remote commander and enter the VTR STOP mode.
Adjustment Page C 2 0 01 01 Set the data.
Adjustment Address 16 3 C 10 EE Set the data, and press PAUSE
button.
Specified Value Data of page: 3, address: 02 is “00”.
Data of page: 3, address: 03 is “00”. 4 3 21 Check that the data is “02”.
(Note2)
Note1: The data of page: 0, address: 10 must be “00”. 5 3 01 0D Set the data, and press PAUSE
button.
Adjusting method: 6 3 02 Check that the data changes to
Order Page Address Data Procedure “00”.
1 Close the cassette compartment 7 3 03 Check that the data is “00”.
without inserting a cassette. (Note3)
2 0 01 01 Set the data. 8 0 01 00 Set the data.
3 3 01 1B Set the data, and press PAUSE
button. Note2: If the data of page: 3, address: 21 is “72”, the tape top being played.
After playing the tape for 1 to 2 seconds, stop it, perform step 5
4 3 02 Check that the data changes in and higher.
the following order. If the data of page: 3, address: 21 is “62”, the tape end being played.
“1B” → “2B” → “00” After rewinding the tape, perform step 5 and higher.
5 3 03 Check that the data is “00”. Note3: If bit 0 of the data is “1”, the EVEN channel is defective. If bit 1 is
“1”, the ODD channel is defective. Contents of the defect is written
(Note2)
into page: C, addresses: 10 and 12. See the following table. (For
6 0 01 00 Set the data. the bit values, refer to “6-4. SERVICE MODE”, “4-3. 3. Bit value
discrimination”. ) If bit 3 of the data is “1”, the tape end being
Note2: If the data is “01”, adjustment has errors or the mechanism deck is played, so rewind the tape and perform the adjustment again.
defective.
When the EVEN channel is defective
Data of page: C,
Contents of defect
address: 10
EE Writing into EEPROM (IC2602) is defective
E8 Adjustment data is out of range
E7 No data is returned from IC2301
6-55
DCR-TRV60/TRV60E/TRV70
Adjusting method:
Order Page Address Data Procedure
1 Playback the recorded signal at
“Preparations before
adjustments”
2 0 01 01 Set the data.
3 0 10 00 Set the data.
4 3 1D Check that the data is “20”.
5 3 01 40 Set the data, and press PAUSE
button.
6 3 02 Check that the data changes
from “40” to “00”.
7 3 03 Check that the data is “00”.
(Note2)
8 Perform “Processing after
Completing Adjustments”
6-56
DCR-TRV60/TRV60E/TRV70
COVER
Fig. 6-3-5.
A B
6-57
DCR-TRV60/TRV60E/TRV70
Mode Camera
Subject Arbitrary
Measurement Point Video terminal of AUDIO VIDEO jack
(75Ω terminated)
Measuring Instrument Oscilloscope
Specified Value Sync level: A = 286 ± 18mV (NTSC)
A = 300 ± 18mV (PAL)
Burst level: B = 286 ± 18mV (NTSC)
B = 300 ± 18mV (PAL)
Switch setting:
DEMO MODE (Menu setting) ........................................ OFF
Adjusting method:
Order Page Address Data Procedure
1 3 0C 02 Set the data, and press PAUSE
button.
2 Check that the sync signal level
(A) satisfies the specified value.
3 Check that the burst signal level
(B) satisfies the specified value.
4 3 0C 00 Set the data, and press PAUSE
button.
B
A
Fig. 6-3-7.
6-58
DCR-TRV60/TRV60E/TRV70
COVER
MIC
Audio oscillator 600 Ω Left
Attenuator Right
Playback
Main unit
TV monitor
Video (Yellow)
Left (White)
Audio level meter
AUDIO/ 47k Ω or Distortion meter
VIDEO Right
OUT
(Red) 47k Ω
47k Ω (1-249-437-11)
Fig. 6-3-8.
6-59
DCR-TRV60/TRV60E/TRV70
Checking Method:
1) Input the 400Hz, –66dBs signal in the MIC jack.
2) Record in the camera mode.
3) Playback the recorded section.
4) Check that the distortion is the specified value.
6-60
DCR-TRV60/TRV60E/TRV70
COVER
Fig. 6-4-1
Note: When reading or writing the 18, 1B, 1C, 1E, 1F page data, select
page: 0, address: 10, and set data: 01, then select 8, B, C, E or F
page. The 18, 1B, 1C, 1E or 1F page can be chosen by this data
setting.
After reading or writing, reset the data of page: 0, address: 10
to “00”.
6-61
DCR-TRV60/TRV60E/TRV70
COVER
Table. 6-4-1.
6-62
DCR-TRV60/TRV60E/TRV70
COVER
Address Contents
F4 EMG code when first error occurs
Upper: MSW code when shift starts when first
F6 error occurs
Lower: MSW code when first error occurs
Lower: MSW code to be moved when first error
F7
occurs
F8 EMG code when second error occurs
Upper: MSW code when shift starts when second
FA error occurs
Lower: MSW code when second error occurs
Lower: MSW code to be moved when second error
FB
occurs
FC EMG code when last error occurs
Upper: MSW code when shift starts when last error
FE occurs
Lower: MSW code when last error occurs
Lower: MSW code to be moved when last error
FF
occurs
When no error occurs in this unit, data “00” is written in the above
addresses (F4 to FF). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency address
(F4 to F7). In the same way, when the second error occurs, the data
corresponding to the error is written in the second emergency address
(F8 to FB). Finally, when the last error occurs, the data corresponding
to the error is written in the last emergency address (FC to FF).
Initializing method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 01, set data: 37, and press the PAUSE
button.
3) Check that the data of page:3, address:02 is “00”.
4) Select page: 0, address: 01, and set data: 00.
6-63
DCR-TRV60/TRV60E/TRV70
Mechanical Position
← UNLOAD LOAD →
EJ BL ULE BL SR BL HL BL STOP BL R/P
← A (MSB)
0 1 0 0 = 4
0 1 1 0 = 6
0 0 1 0 = 2
1 0 1 0 = A
1 0 0 0 = 8
1 1 0 0 = C
1 1 1 0 = E
1 1 1 0 = E
1 1 1 0 = E
1 1 1 0 = E
1 1 1 0 = E
←B
←C
← D (LSB) (Fixed at “0”)
6-64
DCR-TRV60/TRV60E/TRV70
Using method:
1) Select page: 7, address: 0E.
2) By discriminating the bit value of display data, the state of the switch can be discriminated.
6-65
DCR-TRV60/TRV60E/TRV70
Using method:
1) Select page: 3, address: 61.
2) By discriminating the bit value of display data, the state of the switch can be discriminated.
Using method:
1) Select page: 2, address: 60, 62 to 64, 67.
2) By discriminating the display data, the pressed key can be discriminated.
Data
Address 00 19 32 4E 6F 96 FB
(00 to 0C) (0D to 24) (25 to 3F) (40 to 5D) (5E to 81) (82 to AA) (D8 to FF)
FLASH EDIT SEARCH EDIT SEARCH NIGHTSHOT NIGHTSHOT
60 FOCUS BACK LIGHT
(JJ-001 board) + – ON OFF
(KEY AD0) (FP-666 flexible) (FP-666 flexible)
(S5401) (JJ-001 board) (JJ-001 board) (FC-092 board) (FC-092 board)
(IC3102 tl) (S5303) (S5304)
(S5402) (S5403) (S5301) (S5301)
62 PANEL CLOSE PANEL OPEN
(KEY AD1) (CK-130 board) (CK-130 board)
(IC3102 ya) (S5202) (S5202)
63 PANEL REVERCE PANEL NORMAL
(KEY AD2) (FP-667 flexible) (FP-667 flexible)
(IC3102 yg) (S001) (S001)
PHOTO
64
(PHOTO REC)
(KEY AD3) No key input
(FK-4110 block)
(IC3102 yh)
(S006)
67 START/STOP
(KEY AD7) (FK-4110 block) No key input
(IC3102 yl) (S007)
8. LED check
Page 7 Address 07 Bit4, Bit5
Using method:
1) Select page: 7, address: 07, and set data: 20. (Bit5=1)
2) Check that all LED (Recording lamp, Flash LED, Charge LED) are lit.
3) Select page: 7, address: 07, and set data: 00. (Bit5=1)
6-66
DCR-TRV60/TRV60E/TRV70
Initializing method:
1) Select page: 7, address: 00, and set data: 71.
2) Select page: 7, address: 01, set data: 71 and press the PAUSE button.
3) Check that the data of page: 7, address: 02 is “00”.
Using method:
1) The record of use data is displayed at addresses: C8 to CD.
6-67
DCR-TRV60/TRV60E/TRV70
Page 7 Address B0 to C6
Note1: This data will be kept even if the lithium battery (DI-088 board
BT4001) is removed.
Note2: The data of page: 0, address: 10 must be “00”.
Using method:
1) The past self-diagnosis codes are displayed at addresses: BC
to C6.
Refer to “SELF-DIAGNOSIS FUNCTION” for detail of the
self-diagnosis code except for the code being written in the
following table.
Self-diagnosis Code
Block Detailed Symptom/State Correction
Repaired by:
Function Code
Data on A page or D page are Make data on A page and D
E 20 00
rewritten. page correct value.
Note3: When the flash error code (E: 91: **) is displayed. After repair,
clear the error flag in the following method.
1) Select page: 7, address: 00, and set data: 80.
2) Select page: 7, address: 01, set data: 80 and press the PAUSE
button.
3) Check that the data of page: 7, address: 02 is “01”.
6-68
DCR-TRV60/TRV60E/TRV70
〈FOR CAMERA COLOR REPRODUCTION ADJUSTMENT〉
DCR-TRV60/TRV70
Take a copy of CAMERA COLOR
REPRODUCTION FRAME with
a clear sheet for use.
✂
For PAL model
DCR-TRV60E
✂
6-69E
Reverse 987623351.pdf
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2003.03 Official Release — —