Professional Documents
Culture Documents
18 VdS
Issue E Cert/LPCB/ ref.566d/01 (RD020) (RD022) (RD024)
Cert/LPCB/ ref.566d/02 (RD021) (RD023) (RD025)
G412043, G412042, G412041
G412040, G412039, G412038
Cert/LPCB/ ref.566d/03 (RD030) (RD031) (RD032) G413004, G413003, G413002
Variations
Standard Response: RD020, RD022 & RD024
Special Response: RD030, RD031 & RD032
Quick Response: RD021, RD023 & RD025
½”NPT
Thread size
(R½” – ½”BSPT available on special order)
Rapidrop Global Ltd reserves the right to change the design, materials and specifications without notice to continue product development
Data Sheet 4.18 VdS
Issue E Cert/LPCB/ ref.566d/01 (RD020) (RD022) (RD024)
Cert/LPCB/ ref.566d/02 (RD021) (RD023) (RD025)
G412043, G412042, G412041
G412040, G412039, G412038
Cert/LPCB/ ref.566d/03 (RD030) (RD031) (RD032) G413004, G413003, G413002
Metres Height
being thrown upwards towards the 2.00
ceiling. 1.50
1.00
0.50
Floor
0 Minimum Operating
4 3 2 1 0 1 2 3 4
Metres Radius Pressure = 0.35 bar (5 psi)
Flow Characteristics
PENDENT SPRAY
RD022, RD023, RD031 2 Bar Running Pressure 0.5 Bar Running Pressure 3.08 Pressure in pounds per square inch (psi)
Ceiling 3.00 10 30 50 70 90 110 130 150 170
Spray Pendent for installing 2.50 280
Metres Height
only in pendent position giving 70 Partial curve only 260
2.00 Max. Pressure 175 psi
hemispherical discharge below the
5.6
4 3 2 1 0 1 2 3 4 180
K=
Metres Radius 45
80
al
160
in
K=
40
al
No 140
in
35
m
30 No 120
100
RD024, RD025, RD032 UPRIGHT SPRAY 25
2 Bar Running Pressure 0.5 Bar Running Pressure 20 80
Spray Upright for installing only in Ceiling
3.08
3.00 60
15
upright position giving hemispherical 2.50 10 40
Metres Height
34.3 mm
(1 11/32”)
(2 3/16")
(2 3/16”)
55
55 mm
(2 3/16”)
55 mm
29 30.2 mm
(1 5/32") (1 3/16”)
RD020, RD021 & RD030 RD022, RD023 & RD031 RD024, RD025 & RD032 * Bulb sizes shown for
CUP & QR CUP SSP & QR SSP SSU & QR SSU reference only
Figure A Figure B Figure C
DS: 4.18 Rapidrop Global Ltd
Issue E T: +44 (0) 1733 847 510 F: +44 (0) 1733 553 958
17/12/2019 e: rapidrop@rapidrop.com
© 2019 Rapidrop w: www.rapidrop.com Page 2 of 3
Rapidrop Global Ltd reserves the right to change the design, materials and specifications without notice to continue product development
Data Sheet 4.18 VdS
Issue E Cert/LPCB/ ref.566d/01 (RD020) (RD022) (RD024)
Cert/LPCB/ ref.566d/02 (RD021) (RD023) (RD025)
G412043, G412042, G412041
G412040, G412039, G412038
Cert/LPCB/ ref.566d/03 (RD030) (RD031) (RD032) G413004, G413003, G413002
4.
Always check that the sprinklers are the correct model,
style, orifice size, temperature and sensitivity ratings prior to
commencing installation.
5.
Upright sprinklers must be mounted in upright position and
Pendent sprinklers must be mounted in pendent position.
7. Hand tighten the sprinkler into the fitting, then use the correct
sprinkler wrench (Rapidrop Series 20 – See Figure D) to tighten
the sprinkler into the fitting. Ensure that the sprinkler wrench stays
on the wrench flats while tightening the sprinkler. A leak tight joint
requires only 9.5 to 19 Nm (7 to 14 ft.lbs.) torque. i.e. A tangential
force of 6.35 to 12.7kgs. (14 to 28 lbs.) delivered through a 150mm
SERIES 20 WRENCH
(6”) handle will deliver adequate torque. Torque levels over
29Nm (21 ft.lbs.) may distort the orifice seal and result in leakage. Figure D
Rapidrop Global Ltd reserves the right to change the design, materials and specifications without notice to continue product development