This document provides specifications and operating instructions for three power drill models (Cat. Nos. 2402-20, 2403-20, 2404-20). It lists the voltages, speeds, capacities for different materials. It describes installing and removing bits, using the drill in hammering, drilling and driving modes, and adjusting the clutch settings. Safety warnings are provided around battery removal, wearing safety gear, and only using recommended accessories.
This document provides specifications and operating instructions for three power drill models (Cat. Nos. 2402-20, 2403-20, 2404-20). It lists the voltages, speeds, capacities for different materials. It describes installing and removing bits, using the drill in hammering, drilling and driving modes, and adjusting the clutch settings. Safety warnings are provided around battery removal, wearing safety gear, and only using recommended accessories.
This document provides specifications and operating instructions for three power drill models (Cat. Nos. 2402-20, 2403-20, 2404-20). It lists the voltages, speeds, capacities for different materials. It describes installing and removing bits, using the drill in hammering, drilling and driving modes, and adjusting the clutch settings. Safety warnings are provided around battery removal, wearing safety gear, and only using recommended accessories.
No Load Capacities Selecting Drill or Drive Action
Volts No Load Impacts Wood WARNING Always remove battery (Cat. No. 2402-20, 2403-20) Cat. No. DC RPM per Minute Steel Flat Bit Auger Bit Hole Saw Screws (dia.) Masonry pack before changing or removing acces- 1. To use the drilling mode, rotate sories. Only use accessories specifically the torque selector collar until 2402-20 12 LO 0-450 n/a 1/4" Hex 1-1/8" 1" n/a 3/8" n/a the drill symbol appears in HI 0-1700 recommended for this tool. Others may be line with the arrow. hazardous. 2. To use the driving mode rotate 2403-20 12 LO 0-450 n/a 1/2" 1-1/8" 1" 1-3/4" 3/8" n/a HI 0-1700 the torque selector collar until the desired clutch setting ap- 2404-20 12 LO 0-450 LO 6750 1/2" 1-1/8" 1" 1-3/4" 3/8" 3/8" WARNING To reduce the risk of injury, pears in line with the arrow. HI 0-1700 HI 25,500 wear safety goggles or glasses with side The adjustable clutch, when shields. properly adjusted, will slip at a preset torque to prevent driving Fuel Gauge the screw too deep into different To determine the amount of charge left in the bat- FUNCTIONAL DESCRIPTION ASSEMBLY tery, pull the trigger. The Fuel Gauge will light up materials and to prevent dam- age to the screw or tool. for 2-3 seconds. 1 2 3 4 WARNING Recharge only with the To signal the end of charge, 1 light on the fuel Selecting Hammer, Drill or Drive Action charger specified for the battery. For spe- gauge will flash for 2-3 seconds. (Cat. No. 2404-20) cific charging instructions, read the operator’s 1. To use the hammer-drilling manual supplied with your charger and battery. Installing Bits mode, rotate the application Always remove the battery before inserting or selector collar until the hammer Inserting/Removing the Battery removing bits. Select the proper style and size bit symbol appears in line with To remove the battery, push in the release buttons for the job. the arrow. Apply pressure to the 9 and pull the battery pack away from the tool. bit to engage the hammering Cat. No. 2402-20 mechanism. 5 To insert the battery, slide the pack into the body of This driver is intended for use with drill and driver 8 6 the tool. Make sure it latches securely into place. NOTE: The number selected on the torque bits with a 1/4" hex shank and ball detent recess. selector collar has no effect on operation of the 7 1. To install the bit, press the bit into the socket drill in hammer mode. until the collar snaps back and the bit is locked NOTE: When using carbide bits, do not use wa- 1. Keyless chuck into place. ter to settle dust. Do not attempt to drill through (Cat. No. 2403-20, 2404-20) 2. To remove the bit, pull out the collar, then pull steel reinforcing rods. This will damage the 2. Clutch adjusting ring out the bit. carbide bits. 3. Application selector NOTE: It is not necessary to hold the collar out 2. To use the drilling only mode, 4. Speed selector 10 when installing and removing bits. The first time rotate the application selector 5. Belt hook the tool is used, it may be necessary to pull out collar until the drill symbol 6. Fuel Gauge the collar. appears in line with the arrow. 7. Trigger Cat. No. 2403-20, 2404-20 NOTE: The number selected on 8. Control Switch This tool is equipped with a spindle lock. The chuck the torque selector collar has no 9. LED can be tightened with one hand, creating higher grip effect on operation of the drill in 10.Bit holder (Cat. No. 2402-20) strengths on the bit. drilling mode. 1. To open the chuck jaws, turn the sleeve in the 3. To use the driving screws counterclockwise direction. mode rotate the application When using drill bits, allow the bit to strike the selector collar until the drive bottom of the chuck. Center the bit in the chuck symbol appears in line with SYMBOLOGY jaws and lift it about 1/16” off of the bottom. the arrow. Then rotate the torque When using screwdriver bits, insert the bit far selector collar until the desired Volts enough for the chuck jaws to grip the hex of the clutch setting appears in line with bit. the arrow. 2. To close the chuck jaws, turn the sleeve in the The adjustable clutch, when properly adjusted, Direct Current clockwise direction. The bit is secure when the will slip at a preset torque to prevent driving the chuck makes a ratcheting sound and the sleeve screw too deep into different materials and to Impacts per Minute Under can not be rotated any further. prevent damage to the screw or tool. Load (IPM) 3. To remove the bit, turn the sleeve in the coun- No Load Revolutions per terclockwise direction. Minute (RPM) NOTE: A ratcheting sound may be heard when the Underwriters Laboratories, Inc. chuck is opened or closed. This noise is part of the C US United States and Canada locking feature, and does not indicate a problem with the chuck’s operation.