Professional Documents
Culture Documents
26. Configure interface range fast 0/2-10 at VLAN-10 and fast 0/11-20 at VLAN-20 ( L3 Switch-1 )
27. Configure interface range fast 0/2-15 at VLAN-10 and fast 0/16-22 at VLAN-20 ( L3 Switch-2 )
28. Make interface fast 0/1 as a trunk at both switch
29. Allow only VLAN 10 from this trunk link
30. Add VLAN 50 also + VLAN 10
31. Without 80 all VLAN should be allow
32. Also VLAN 90 should remove from Trunk link
33. No VLAN can pass from trunk link
34. All VLAN should be allow
35. Change native VLAN to 30
36. Discover information about neighbor using CDP
37. Discover information about neighbor with detail
38. Check CDP timers
39. Disable CDP globally
40. Disable CDP at interface fifth
41. Enable CDP again
42. Enable CDP again at interface fifth
43. Connect two Switch Point to point using two cable and enable LLDP at both switch’s
44. Discover brief information about neighbor using LLDP
45. Discover full information about neighbor using LLDP
46. Disable transmitting LLDP message at one interface
47. Disable receiving LLDP message at one interface
Sw-A Sw-B
Sw-C Sw-D
PC-A
PC-B PC-C PC-D
R-1
R-2 R-3
Full
Mesh
R-4 R-5
76. Configure loopback interface at all routers → For Example → Router-1 - Loop-1 = 1.1.1.1/24
77. Configure RIPv2 between at all routers for exchanging routes
78. Check Route-1 Routing table – Router-1 should receive 10 RIP routes
79. Remove RIPv2 for all Routers in full mesh topology
80. Configure OSPF single area ( area-20 ) at all routers
81. Check Router-2 OSPF neighbor table – should have 4 neighbor
82. Check Router-3 OSPF database
83. Check Router-4 Routing table – should receive 10 OSPF routes
.1
3.3.3.0/24
.2
.100
10.0.0.100 .3
PC-A 10.0.0.1
90. Make connection → which PC-A have reachability only with PC – 3.3.3.3
91. For destination 3.3.3.3 from PC-A the R-1 path should as best path and R-3 path should be as backup
path
Internet
PC-A
Internet
Internet
100. Configure Router As DHCP Server to provide automatic address just for ( PC-A,B and C)
101. Exclude other addresses at Router ( Means Router can Provide only 3 IP addresses )
102. Show the IP addresses list at router which router distributed to PC’s
103. Configure Switch As DHCP Server to provide automatic address just for PC-D and PC-E
104. Exclude other addresses at Switch ( Means Switch should Provide only 2 IP address )
105. PC-F should not be able to achieve automatic IP Address
Internet
Local Network
DHCP
PC-D SERVER
R-B R-C
R-A
Local Network
Web-Server
TFTP-Server
PC-2 PC-6
PC-3 PC-8
R-2 Internet
R-1
DHCP
S-1
SW-1 SW-2
PC-1
S-2
TFTP
PC-4 PC-5
R-2 Internet
R-1
Local Network
192.168.1.0/24
Evil - PC
SW-2
DHCP- Server
PK-ISP UAE-ISP
AFTEL
Internet
155.1.1.0/30
PC-1
Wireless Router-1
PC-2
PC-3
Wireless Router-2
PC-4
Smart-Pone-1
DNS Server AMAZON Server
WAP
Smart-Pone-2