Professional Documents
Culture Documents
Pull Out
Pull Out
(Reaffirmed 2021) (
(
Free Standard provided by BIS via BSB Edge Private Limited to Ashu Tiwari -
Dehradun(ashutiwari910@gmail.com) 103.248.122.244 [for non-commercial use only].
IS : 11309 - 1985
Indian Standard
METHOD FOR
CONDUCTING PULL-OUT TEST ON
ANCHOR BARS AND ROCK BOLTS
© Copyright 1985
INDIAN STANDARDS INSTITUTION
This publication is protected under the Indian Copyright Act (XIV of 1957) and
reproduction in whole or in part by any means except with written Permission of the
publisher shall be deemed to be an Infringement of copyright under the said Act,
Free Standard provided by BIS via BSB Edge Private Limited to Ashu Tiwari -
Dehradun(ashutiwari910@gmail.com)
IS : 11309 - 1985 103.248.122.244 [for non-commercial use only].
Indian Standard
METHOD FOR
CONDUCTING PULL-OUT TEST ON
ANCHOR BARS AND ROCK BOLTS
0. FOREWORD
0.1 This Indian Standard was adopted by the Indian Standards
Institution on 29 June 1985, after the draft finalized by the Rock
Mechanics Sectional Committee had been approved by the Civil
Engineering Division Council. ' -
1. SCOPE
1.1 This standard lays down the method for conducting anchor pull-out
test in rock and the evaluation of bondstrength between reinforcement
and grout concrete or grout concrete and rock.
NOTE —-- This method assumes that diameter of the bore in .rock throughout the
length of reinforcement is uniform and cement mortar density around the reinforce-
ment and throughout the length of reinforcement is also uniform.
2. EQUIPMENT
2.1 Central Hole Jack -— It is a special jack in which ram has a
dentral hole throughout the height of the jack.
*Rules for roundin g Off numerical values revised .
2
Free Standard provided by BIS via BSB Edge Private Limited to Ashu Tiwari -
Dehradun(ashutiwari910@gmail.com) 103.248.122.244 [for non-commercial
IS : 11309 - 1985use only].
3.2 The upper end of the bar under test should project up to the length
of 50 cm, so that the double nuts may be fitted in it above the 40 cm
high spring-return central-hold jack.
3.3 The rock surface around the reinforcement over a diameter of 60 cm
should be made fiat by hand chiselling and plastered by a rich cement-
sand mortar. A mild steel plate of 25 mm thickness having a hole equal
to the diameter of bore hole should be placed over it.
3.4 The cement-sand'slurry should be filled in bore-hole all round the
anchor bar with the help of grouting machine at suitable pressure.
3.5 Prior to starting the actual test it should be ensured that the curing
period of grout mix filled in the bore-hole around the anchor is
completed (see IS : 6066-1985fig ).
4. APPLICATION OF LOADING
4.1 Central—hole jack should be fitted in anchor bar. Two dial gauges,
0'01 mm least count and 50 mm travel, should be fitted on diagonally
opposite sides of central-hole jack to record the movement of the anchor
bar at the time of loading ( Fig. 1 ).
4.2 Pressure should be applied, with the help of hydraulic pump
connected with the central-hole jack of 50 tonne capacity having a central
hole of 60 mm with uniform but slow rate of 230 kg/rnin as the pulling
bar should not be subjected to any jerk till the bar starts coming out,
During the application of pressure, the dial gauge observations should
also be recorded at every load interval of 1 tonne. The plot of pull versus
bolt extension should also be made as shown in Fig. 2 for better under-
standing ofmode of failure.
—__._
3
Emma. .50-.“q ”Sm mDémm M .03
a . . c I «a o c
. ... .
. .
....o w ‘ b. 0" . I O I .u” . . m l ..A .q. .P: . a ct I C
6 o ‘ .,C 0
‘ A. . A:
con ' h .. ...:
09-.- l u.
.
.r a
. . ...
-u...‘ “:4... .. .. A.O.m
......3 \
h ... .. . ...» r L 7%. J a .J.r
< ‘ «‘0. m
d ... o 0.. ...
I ‘I
. 1 .... .u. .. m 2 ..r
..... w .....L
p. . ..b.. . ..
. I mhmmozooxxooa ..
». m<km02 ...zmzmo ..
. r.
I
bola
U
mmqm can - n!
up
» “5-
.
....
o
...
'fi ~ 'd‘f“.l
.....w... qoz kzmzmo a lo
...mpqgm m: :.u. .
e . .. ...... .. I.” o) in . o a .
o
' I .a ...‘o...... ...... k ...
o
.._— 1:
.- t 0 v
n u o I C a “pm-...‘H ‘.ak.aal.lcngu
. . \
z////</ /
mN
munZOI
m03<o mmzmmmmm o._._.mzo<z
gtod‘mdo pom.
W
H] .
x042. mac: 4<akzwo
monqo .210
$5.54?
.53.“. w 2I\ ...qm 1am no Eda
qm morn. 24 QwumOn—zfim
IS : 11309 - 1985
Dehradun(ashutiwari910@gmail.com) 103.248.122.244 [for non-commercial use only].
Free Standard provided by BIS via BSB Edge Private Limited to Ashu Tiwari -
Free Standard provided by BIS via BSB Edge Private Limited to Ashu Tiwari -
Dehradun(ashutiwari910@gmail.com) 103.248.122.244 [for non-commercial use only].
IS : 11309 - 1985
PULL
JACK
4.9 The bolts that form part of the actual rock support system shall not
be tested beyond 10 percent more than the design load.
5.2 The bond strength is worked out by the following formula in case
bolt is below up to failure between grout and rock.
W>< 1000
Bond strength Tr = kgf/cm2 ......... (l)
ZERXL
where