Professional Documents
Culture Documents
Intelligent Heat
Detector
SIGA-HRD
S853
Signature Series detectors mount Remote LED SIGA-LED - The remote LED connects to the
to North American 1-gang boxes, SIGA-SB or SIGA-SB4 Standard Base only. It features a North
3-1/2 inch or 4 inch octagon American size 1-gang plastic faceplate with a white finish and red
boxes, and to 4 inch square elec- Self-locking tab
alarm LED.
trical boxes 1-1/2 inches (38 mm) SIGA-TS4 Trim Skirt - Supplied with 4 inch bases, it can also
deep. They mount to European be ordered separately to use with the other bases to help hide
BESA and 1-gang boxes with 60.3 surface imperfections not covered by the smaller bases.
mm fixing centers. See mounting LED Indicator
Sounder Bases - Signature Series sounder bases are designed
base installation and wiring for
for use where localized or group alarm signaling is required.
more information.
• SIGA-AB4G bases provide sounder capability to Signature
Series to heat and smoke detectors. They are not intended
for use with combination carbon monoxide detectors in Fire-
Sensing and reporting technology plus-CO mode.
The microprocessor in each detector provides additional benefits - • SIGA-AB4GT bases provide sounder capability to Signature
Self-diagnostics and History Log, Automatic Device Mapping, and Series smoke and heat detectors, as well as carbon monox-
Fast, Stable Communication. ide detectors when used with a SIGA-TCDR Temporal Pattern
Generator.
Self-diagnostics and History Log - Each Signature Series • SIGA-AB4G-LF bases provide 520 Hz low frequency
detector constantly runs self-checks to provide important mainte- sounder capability to Signature Series smoke and heat detec-
nance information. The results of the self-check are automatically tors, as well as carbon monoxide detectors when used with a
updated and permanently stored in the detector’s non-volatile SIGA-TCDR Temporal Pattern Generator. The SIGA-AB4G-LF
memory. is suitable for applications requiring low frequency audible
tones.
Automatic Device Mapping - The loop controller learns where
each device’s serial number address is installed relative to other
devices on the circuit. The mapping feature provides supervision
of each device’s installed location to prevent a detector from being Warnings & Cautions
reinstalled (after cleaning etc.) in a different location from where it • This detector does not operate without electrical power. As
was originally. fires frequently cause power interruption, discuss further safe-
Fast Stable Communication - On-board intelligence means less guards with the local fire protection specialist.
information needs to be sent between the detector and the loop • This detector does not sense fires in areas where heat cannot
controller. Other than regular supervisory polling response, the reach the detector. Heat from fires in walls, roofs, or on the
detector only needs to communicate with the loop controller when opposite side of closed doors may not reach the detector.
it has something new to report. • This heat detector by itself does not provide life safety protec-
tion Use this detector with ionization and/or photoelectric
smoke detectors.
• This detector does not detect oxygen levels, smoke, toxic
gases, or flames. Use this device as part of a broad-based
life safety program which includes a variety of information
sources pertaining to heat and smoke levels, extinguishment
systems, visual and audible devices, and other safety mea-
sures.
• Independent studies indicate that heat detectors should only
be used when property protection alone is involved. Never
rely on heat detectors as the sole means of fire protection.
Compatible Bases
SIGA-SB Detector Mounting Base - Standard
SIGA-SB4 4-inch Detector Mounting Base c/w Trim Skirt
SIGA-RB Detector Mounting Base w/Relay
SIGA-RB4 4-inch Detector Mounting Base w/Relay, c/w Trim Skirt 0.2 (.09)
SIGA-IB Detector Mounting Base w/Fault Isolator
SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator, c/w Trim Skirt
SIGA-LED Remote Alarm LED (not for EN54 applications)
SIGA-AB4G Audible (Sounder) Base for Fire Detectors 0.3 (0.15)
SIGA-AB4G-LF Low Frequency Audible (Sounder) Base for CO and Fire Detectors 0.3 (0.15)
SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors 0.3 (0.15)
SIGA-TS4 Trim Skirt (supplied with 4-inch bases) 0.1 (.04)
SIGA-DMP Detector Mounting Plate 3.0 (1.4)
SIGA-RTA Detector Removal Tool
SIGA-VA Detector Cleaning Tool
06-03-16
UQGS.S1122
Heat-automatic Fire Detectors
Page Bottom
EDWARDS, A DIV OF UTC FIRE & SECURITY AMERICAS CORPORATION, INC. S1122
8985 TOWN CENTER PKWY
BRADENTON, FL 34202 USA
Heat detectors, Model(s) Rated 135 F Model 73340, Rated 135F Model 73342, Rated 194 F Model 73341, Rated 194 F Model 73343,
ZC20FTU-3,SC20FTU-3,MC20FTU-3
Spacing (Ft)
FT/ROR D5 - 135 70 35
JTW-ZDM-S2HFSI FT D5 - 135 50 25
SIGA-DHI, JTW-ZDM-SIGA-DHC
FT/ROR D5 - 135 50 25
SIGA-HFD FT D5 - 135 50 25
SIGA2-HFS FT D5 - 135 50 25
SIGA2-PHCOS, SIGA2-HCOS
FT D5 - 135 50 25
ZC20RRU-3,SC20RRU-3,MC20RRU-3
FT/ROR None - - - -
D5 - For use only with Listed control units with which compatibility was determined by test.
FT - Fixed temperature
Trademark and/or Tradename: ""E" in a Shield" , "Dukane" , "ESL" , "Edwards Co Inc" , "Edwards Company Inc." , "Edwards System
Technology" , "FAST" , "Fire Alarm Systems Technology" , "FireworX" , "G.S. Building Systems Corp." , "GE Security" , "GE Security Inc" , "GS" ,
"GSBS" , "Interlogix Inc" , "KIDDE" , "Mirtone" , "Sentrol" , "Vigilant" , "Walter Kidde Portable Equipment INC." , "Ziton" , ,
, , , , ,
© 2016 UL LLC
The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured
under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Certified and covered under UL's Follow-Up
Service. Always look for the Mark on the product.
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name... 22/9/2016
UQGS.S1122 - Heat-automatic Fire Detectors Page 2 of 2
UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide
Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) must be presented in their entirety and in a non-
misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with
permission from UL" must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the
following format: "© 2016 UL LLC".
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name... 22/9/2016