Professional Documents
Culture Documents
HE 1 Form A
TYPICAL APPLICATIONS
1 6
Measuring instruments
2 5
Data communication equipment
Telephone equipment
3 4 Automatic meter reading device
Note: Please contact our sales representative for automotive applications of PhotoMOS.
(Unit: mm)
TYPES
RATING
C 1.0 A 0.8 A 0.70 A 0.5 A 0.4 A 0.25 A 0.05 A 0.04 A 0.4 A 0.25 A 0.16 A connection: DC
A connection:
Peak load current Ipeak - 1.8 A 1.5 A 1.0 A 0.75 A 0.6 A 0.5 A 0.09 A 0.06 A 0.6 A 0.5 A 0.4 A 100 ms (1 shot),
VL = DC
Power
Pout - 360 mW
dissipation
Total power
PT - 410 mW
dissipation
I/O isolation voltage Viso - 1,500 Vrms 5,000 Vrms
Ambient temperature
Tstg - –40 to +100°C
(Storage)
Junction temperature Tj - 125°C
IFoff - IL = Max.
current Typical 0.8 mA 1.3 mA
LED dropout Typical 1.25 V (1.14 V at IF = 5 mA)
VF - IF = 50 mA
voltage Maximum 1.5 V
Typical 0.6 Ω 0.74 Ω 1.8 Ω 2.6 Ω 5.5 Ω 12.4 Ω 85 Ω 345 Ω 5.5 Ω 12.4 Ω 20 Ω IF = 5 mA
Ron A IL = Max.
Maximum 1Ω 1.4 Ω 2.5 Ω 4Ω 8Ω 16 Ω 200 Ω 500 Ω 8Ω 16 Ω 30 Ω Within 1 s
Typical 0.3 Ω 0.37 Ω 0.9 Ω 1.4 Ω 2.7 Ω 6.2 Ω 60 Ω 345 Ω 2.7 Ω 6.2 Ω 15 Ω IF = 5 mA
On resistance Ron B IL = Max.
Output
Maximum 3 ms 2 ms 3 ms 2 ms 1 ms 4 ms 3 ms
Typical 0.07 ms 0.09 ms 0.1 ms 0.06 ms 0.05 ms 0.04 ms 0.06 ms 0.05 ms 0.06 ms IF = 5 mA
Turn off time* Toff -
Maximum 0.2 ms IL = Max.
Input
90%
10%
Output
Ton Toff
REFERENCE DATA
1-1.Load current vs. ambient temperature 1-2.Load current vs. ambient temperature 2-1.On resistance vs. ambient temperature
characteristics characteristics characteristics
Allowable ambient temperature: –40 to +85°C Allowable ambient temperature: –40 to +85°C Measured portion: between terminals 4 and 6;
Type of connection: A Type of connection: A LED current: 5 mA;
Continuous load current: Max. (DC)
5.0
4.5
0.6 50
4.0
AQV251
Load current (mA)
On resistance (Ω)
0.5
Load current (A)
3.5
40
AQV252 3.0 AQV257
0.4
AQV259
30 2.5
AQV255
0.3
AQV257 2.0 AQV255
AQV258
(H)
AQV253 20
0.2 1.5
(H)
AQV254
1.0 AQV252
0.1 AQV256H 10
0.5
AQV251
0 0 0
-40 -20 0 20 40 60 80 85 100 -40 -20 0 20 40 60 80 85 100 -40 -20 0 20 40 60 80 85
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
35
400 AQV251
30 AQV258 3
On resistance (Ω)
0 0 0
-40 -20 0 20 40 60 80 85 -40 -20 0 20 40 60 8085 -40 -20 0 20 40 60 8085
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
3-2.Turn on time vs. ambient temperature 4-1.Turn off time vs. ambient temperature 4-2.Turn off time vs. ambient temperature
characteristics characteristics characteristics
LED current: 5 mA; Load voltage: Max. (DC); LED current: 5 mA; Load voltage: Max. (DC); LED current: 5 mA; Load voltage: Max. (DC);
Continuous load current: Max. (DC) Continuous load current: Max. (DC) Continuous load current: Max. (DC)
5 0.4 0.5
4 0.4
AQV253H 0.3
3 0.3
0.2
AQV251, AQV252, AQV255
2 AQV254H 0.2
AQV253H, AQV254H, AQV256H
AQV256H 0.1 AQV254
1 0.1
AQV253, AQV257
AQV259, AQV258
0 0 0
-40 -20 0 20 40 60 80 85 -40 -20 0 20 40 60 80 85 -40 -20 0 20 40 60 80 85
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
5-1.LED operate current vs. ambient 5-2.LED operate current vs. ambient 6-1.LED turn off current vs. ambient
temperature characteristics temperature characteristics temperature characteristics
Load voltage: Max. (DC); Load voltage: Max. (DC); Load voltage: Max. (DC);
Continuous load current: Max. (DC) Continuous load current: Max. (DC) Continuous load current: Max. (DC)
4 5 4
4
LED operate current (mA)
3 3
3
2 AQV253H, AQV254H, 2
AQV251, AQV252, AQV253, AQV256H
2 AQV251, AQV252, AQV253,
AQV254, AQV255, AQV257, AQV254, AQV255, AQV257,
AQV258, AQV259 AQV258, AQV259
1 1
1
0 0 0
-40 -20 0 20 40 60 80 85 -40 -20 0 20 40 60 80 85 -40 -20 0 20 40 60 80 85
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
Current (A)
0.5
AQV252
1.4 0.4 AQV255
4
LED turn off current (mA)
8-2.Current vs. voltage characteristics of 9-1.Off state leakage current vs. load 9-2.Off state leakage current vs. load
output at MOS portion voltage characteristics voltage characteristics
Measured portion: between terminals 4 and 6; Measured portion: between terminals 4 and 6; Measured portion: between terminals 4 and 6;
Ambient temperature: 25°C Ambient temperature: 25°C Ambient temperature: 25°C
40
AQV259 10-3 10-3
Current (mA)
30
Off state leakage current (A)
10 10-6 10-6
-8 -6 -4 -2
2 4 6 8
AQV259
-10
Voltage (V)
10 -9 10-9 AQV254H
-20
-30 AQV256H
0 20 40 60 80 100 0 20 40 60 80 100
Load voltage (V) Load voltage (V)
10-1.Turn on time vs. LED forward current 10-2.Turn on time vs. LED forward current 11-1.Turn off time vs. LED forward current
characteristics characteristics characteristics
Measured portion: between terminals 4 and 6; Measured portion: between terminals 4 and 6; Measured portion: between terminals 4 and 6;
Load voltage: Max. (DC); Continuous load current: Load voltage: Max. (DC); Continuous load current: Load voltage: Max. (DC); Continuous load current:
Max. (DC); Ambient temperature: 25°C Max. (DC); Ambient temperature: 25°C Max. (DC); Ambient temperature: 25°C
3.0 12 0.12
2.5 10 0.10
Turn on time (ms)
1.5 6 0.06
AQV254
AQV252
1.0 4 0.04 AQV259, AQV258
AQV253, AQV254, AQV257, AQV255
AQV254H
0.5 AQV259 2 0.02
AQV256H
AQV258
0 0 0
0 10 20 30 40 50 60 0 10 20 30 40 50 60 0 10 20 30 40 50
LED forward current (mA) LED forward current (mA) LED forward current (mA)
0.08 400 80
0.04 200 40
DIMENSIONS CAD The CAD data of the products with a “CAD” mark can be downloaded from our Website. Unit: mm
CAD Through hole terminal type CAD Surface mount terminal type PC board pattern
External dimensions External dimensions (BOTTOM VIEW)
Max.10° 5.08
Max.10°
6-0.8 dia. 2.54
2.54
7.62
7.62 ±0.05
6.4
6.4±0.05
6.4 ±0.05
7.6
Max.10°
1 Tolerance: ±0.1
8.8 ±0.05 3.4 8.8±0.05 3.4 Recommended mounting pad
3.9 ±0.2
(TOP VIEW)
3.4
0.47 0.47
3
0.2 +0.2
ー0
0.47
0.47 0.47 1.25 1.25
8.3
0.47 1.25
1.9
1.25 1.25
1.25 2.54 2.54
Terminal thickness: t = 0.25
2.54 2.54 General tolerance: ±0.1 1.5
Terminal thickness: t = 0.25
General tolerance: ±0.1 2.542.54
Tolerance: ±0.1
Output Load
Schematic Connection Wiring diagram
configuration type
1 6 6 Load
E1 IF 2 5
AC/DC A IL VL (AC, DC) IL VL (AC, DC)
3 4 4
Load
1 6 Load 6
+ +
E1 IF 2 5 IL VL (DC) 5 IL VL (DC)
3 4 Load
1 6
2 5 1 6
1 Form A DC B
E1 IF 2 5 5 Load
3 4
3 4 IL VL (DC) 4 IL VL (DC)
* + +
Load
Can be also connected as 2 Form A type. (However, the sum of the continuous load current
should not exceed the absolute maximum rating.)
1 6 Load 6
+ +
E1 IF 2 5 IL VL (DC) 5 IL VL (DC)
DC C
3 4 4 Load
SAFETY STANDARDS
SAFETY WARNINGS
o not use the product under conditions that exceed the range
D heck the wiring diagrams in the catalog and be sure to
C
of its specifications. It may cause overheating, smoke, or fire. connect the terminals correctly. If the device is energized
Do not touch the recharging unit while the power is on. There with short circuit or any wrong connection, it may cause
is a danger of electrical shock. Be sure to turn off the power unexpected malfunction, abnormal heat or fire.
when performing mounting, maintenance, or repair operations
on the device (including connecting parts such as the terminal
board and socket).
Derating design
Derating is a significant factor for reliable design and product life. 5) When packing printed circuit boards and equipment, avoid using
Even if the conditions of use (temperature, current, voltage, etc.) of high-polymer materials such as foam styrene, plastic, and other
the product are within the absolute maximum ratings, reliability may materials which carry an electrostatic charge.
be lowered remarkably when continuously used in high load 6) When storing or transporting PhotoMOS®, the environment should
conditions (high temperature, high humidity, high current, high not be conducive to generating static electricity (for instance, the
voltage, etc.) Therefore, please derate sufficiently below the humidity should be between 45% and 60%), and PhotoMOS®
absolute maximum ratings and evaluate the device in the actual should be protected using conductive packing materials.
condition.
Moreover, regardless of the application, if malfunctioning can be Unused terminals
expected to pose high risk to human life or to property, or if products The No. 3 terminal is used with the circuit inside the device.
are used in equipment otherwise requiring high operational safety, in Therefore, do not connect it to the external circuitry with either
addition to designing double circuits, that is, incorporating features connection method A, B or C. (1 Form A 6-pin type)
such as a protection circuit or a redundant circuit, safety testing
should also be carried out. Short across terminals
Do not short circuit between terminals when device is energized,
pplying stress that exceeds the absolute maximum
A since there is possibility of breaking of the internal IC.
rating
If the voltage or current value for any of the terminals exceeds the Surge voltages at the input
absolute maximum rating, internal elements will deteriorate because If reverse surge voltages are present at the input terminals, connect
of the overvoltage or overcurrent. In extreme cases, wiring may a diode in reverse parallel across the input terminals and keep the
melt, or silicon P/N junctions may be destroyed. reverse voltages below the reverse breakdown voltage.
Therefore, the circuit should be designed in such a way that the load Typical circuits are below shown.
never exceed the absolute maximum ratings, even momentarily. 1) 6-pin
2 5
Load
60 3 4
40 Clamp diode is
connected in parallel
with the load.
20
1 6
0 2 5
-40 -20 0 20 40 60 8085 100
Ambient temperature (°C)
Load
3 4
For AQV209G, APV1111GV, APV3111GV
50 CR snubber is
connected in parallel
with the load.
40
LED forward current (mA)
30
20 1 2 3 4
Load
Clamp diode is
10 connected in parallel
with the load.
0
-40 -20 0 20 40 60 80 85 100
Ambient temperature (°C)
1 2 3 4
Load
CR snubber is
Ripple in the input power supply connected in parallel
If ripple is present in the input power supply, observe the following: with the load.
1) For LED forward current at Emin, please maintain the value
mentioned at “■Recommended LED forward current.”
1 2 3 4
2) Please make sure the LED forward current for Emax. is no higher A varistor is
Load
than 50 mA. connected in parallel
with PhotoMOS®
3) Please maintain the input voltage at least 4V for Emin. (GU, RF (3) CC Type
and Power voltage-sensitive type). 1 4
Load
4) Please make sure the input voltage for Emax. is no higher than 6V 2 3
(GU and RF voltage-sensitive type).
Clamp diode is
connected in parallel
5) Please make sure the input voltage for Emax. is no higher than 30V
with the load.
(Power voltage-sensitive type).
1 4
Load
2 3
Water condensation
Water condensation occurs when the ambient temperature changes
suddenly from a high temperature to low temperature at high
humidity, or the device is suddenly transferred from a low ambient
temperature to a high temperature and humidity. Condensation
causes the failures such as insulation deterioration. Panasonic
Corporation does not guarantee the failures caused by water
condensation. The heat conduction by the equipment the
PhotoMOS® is mounted may accelerate the water condensation.
Please confirm that there is no condensation in the worst condition
of the actual usage. (Special attention should be paid when high
temperature heating parts are close to the PhotoMOS®.)
Direction of picking
21±0.8
1.75±0.1
Tractor feed holes 1.5 +0.1
ー 0 dia.
2.4±0.2
180±3dia.
60 ±3dia.
ー 0.1
+0.3
TSON
12
Device mounted
4-pin on tape
1.2 ±0.3 1.05±0.1dia.
5.5±0.1
2±0.1
4±0.1
(1) When picked from 1/2-pin side: Part No. AQY2C*R*PX, 13±0.5 dia.
AQY2C*R*P1X (Shown above) 13±1.5 1.2±0.5
*Quality of material: Polystyrene (PS)
(2) When picked from 3/4-pin side: Part No. AQY2C*R*PZ
Direction of picking
21±0.8
80 ±1dia.
Tractor feed holes 1.5 +0.1
ー0 dia.
1.75±0.1
0.4 ±0.05 4.0 ±0.1
2.4±0.2
2.5±0.2
2±0.5
ー 0.1
+0.3
250 ±2dia.
80 ±1 dia.
12.0
VSSOP Device mounted
4-pin on tape
3.3±0.3 1±0.1dia. 8±0.1 2±0.1 5.5±0.1
(1) When picked from 1 and 4-pin side: Part No. AQY*TY (Shown above)
(2) When picked from 2 and 3-pin side: Part No. AQY*TW *Quality of material: Paper 13 ±0.5dia. 14±1.5 2 ±0.5
2±0.5
±0.3
SON
12
250 ±2dia.
Device mounted
80 ±1 dia.
4-pin on tape
1.5±0.1dia. 4±0.1 2±0.1
5.5±0.1
2±0.3
(1) When picked from 1 and 4-pin side: Part No. AQY*MY,
AQY*M1Y (Shown above)
(2) When picked from 2 and 3-pin side: Part No. AQY*MW
*Quality of material: Paper 13 ±0.5dia. 14±1.5 2 ±0.5
Direction of picking
End of the part number 1Y
1.75±0.1
21±0.8
ー 0.1
12.0 +0.3
2±0.5
SSOP Device mounted
180±3dia.
60 ±3dia.
5.5±0.1
4-pin on tape
2.7±0.3 4.0±0.1
1.5+0.1
ー 0 dia.
(1) When picked from 1 and 4-pin side: Part No. AQY*VY, AQY221*V1Y,
APV*111*VY,
APV*111*V1Y (Shown above) 13±0.5 dia.
(2) When picked from 2 and 3-pin side: Part No. AQY*VW, APV*111*VW *Quality of material: Polystyrene (PS)
13±1.5 1.2±0.5
21±0.8
Direction of picking 80 ±1dia.
1.75±0.1
ー 0.1
+0.3
4.7±0.1
250 ±2dia.
80 ±1 dia.
12
SOP
4-pin Device mounted on tape
2.8±0.3 4±0.1 1.55±0.1dia.
12±0.1 2±0.1
(1) When picked from 1/2-pin side: Part No. AQY*SX, APV**21SX (Shown above)
(2) When picked from 3/4-pin side: Part No. AQY*SZ, APV**21SZ 13 ±0.5dia. 14±1.5 2 ±0.5
*Quality of material: Paper
21±0.8
80 ±1dia.
Direction of picking
1.75±0.1
Tractor feed holes ±0.1
0.3±0.05 1.5 +0.1
ー 0 dia.
4 7.2±0.1
2±0.5
5.5±0.1
ー 0.1
+0.3
250 ±2dia.
80 ±1 dia.
6.9 ±0.1
SOP
12
6-pin Device mounted on tape
12±0.1 2±0.1 1.55±0.1dia.
2.8±0.3
(1) When picked from 1/2/3-pin side: Part No. AQV*SX (Shown above) *Quality of material: Paper 13 ±0.5dia. 14±1.5 2 ±0.5
(2) When picked from 4/5/6-pin side: Part No. AQV*SZ
Direction of picking
1.75±0.1
Tractor feed holes
0.3±0.05 1.5 +0.1
ー 0 dia.
7.5±0.1
7.5±0.1
10.15±0.1
ー 0.1
16 +0.3
SOP
8-pin Device mounted 21±0.8
on tape
80 ±1dia.
4±0.1 1.55±0.1dia.
2.8±0.3
12±0.1 2±0.1
2±0.5
(1) When picked from 1/2/3/4-pin side: Part No. AQW*SX (Shown above)
(2) When picked from 5/6/7/8-pin side: Part No. AQW*SZ
250 ±2 dia.
80 ±1dia.
Direction of picking
1.75±0.1
ー 0.1
16 +0.3
4±0.1 1.55±0.1dia.
2.8±0.3 12±0.1 2±0.1
(1) When picked from 1/2/3/4/5/6/7/8-pin side: Part No. AQS*SX (Shown above)
(2) When picked from 9/10/11/12/13/14/15/16-pin side: Part No. AQS*SZ
21±0.8
80 ±1dia.
Direction of picking
1.75±0.1
ー 0.1
12+0.3
5.25±0.1
Surface mount
terminal Device mounted on tape
12±0.1 2±0.1 1.55±0.1dia.
4.2±0.3
(1) When picked from 1/2-pin side: Part No. AQY*HAX, AQY210HLAX (Shown above) *Quality of material: Paper 13±0.5dia. 13.5±2.0 2±0.5
(2) When picked from 3/4-pin side: Part No. AQY*HAZ, AQY210HLAZ
21±0.8
80 ±1dia.
Direction of picking
1.75±0.1
300±2dia.
DIP 6-pin
80±1dia.
ー 0.1
+0.3
9.2±0.1
Surface mount
16
(1) When picked from 1/2/3-pin side: Part No. AQV*AX (Shown above) *Quality of material: Paper 13 ±0.5dia. 17.5±2 2±0.5
(2) When picked from 4/5/6-pin side: Part No. AQV*AZ
Note: “ * ” indicates characters of number or alphabet.
Direction of picking
1.75±0.1
Tractor feed holes ±0.1
0.3±0.05
1.5+0.1
ー0 dia.
4 10.1±0.1
7.5±0.1
DIP 8-pin
ー 0.1
+0.3
10.2±0.1
Surface mount
16
21±0.8
terminal Device mounted on tape
80 ±1dia.
12±0.1 2±0.1 1.55±0.1dia.
4.5±0.3
2±0.5
(1) When picked from 1/2/3/4-pin side: Part No. AQW*AX (Shown above)
(2) When picked from 5/6/7/8-pin side: Part No. AQW*AZ
300±2dia.
80±1dia.
Direction of picking
1.75±0.1
Tractor feed holes
0.3±0.05 1.5 +0.1
ー0 dia.
4±0.1 10.2±0.1
DIP 8-pin
7.5±0.1
Surface mount
10.3±0.1
ー 0.1
16+0.3
terminal
*Quality of material: Paper 13 ±0.5dia. 17.5±2 2±0.5
High I/O Device mounted on tape
isolation
12±0.1 2±0.1 1.55±0.1dia.
voltage type 4.2±0.3
21±0.8
100±1dia.
Direction of picking
±0.1
330±2 dia.
Power-DIP
100±1dia.
24.0 ±0.3
4-pin
9.7±0.1
(1) When picked from 1/2-pin side: Part No. AQY*AX (Shown above) *Quality of material: Paper 13 ±0.5dia. 25.5±2 1.7±0.8
(2) When picked from 3/4-pin side: Part No. AQY*AZ
21±0.8
80 ±1dia.
Direction of picking
1.75±0.1
DIP 6-pin
ー 0.1
+0.3
9.2±0.1
300±2dia.
Surface mount 80±1dia.
16
terminal
Device mounted on tape
(Photovoltaic
MOSFET driver) 12±0.1 4±0.1 1.6±0.1dia.
±0.3
4.5
2±0.1
(1) When picked from 1/2/3-pin side: Part No. APV1122AX (Shown above) *Quality of material: Paper 13 ±0.5dia. 17.5±2 2±0.5
(2) When picked from 4/6-pin side: Part No. APV1122AZ
Note: “ * ” indicates characters of number or alphabet.
2) Tube
Devices are packaged in a tube so that 1-pin is on the stopper B
side. Observe correct orientation when mounting them on PC
boards.
(PD type) (SOP type)
Stopper B Stopper A
DC AQZ192 60 V DC 10 A DC 5, 12, 24 V DC
type AQZ197 200 V DC 5 A DC 100 V DC
12 V AC
AQZ202G Peak AC, DC 60 V Peak AC, DC 6 A
5, 12, 24 V DC
24 V AC
AC/ AQZ205G Peak AC, DC 100 V Peak AC, DC 4 A 48 V DC
DC
type AQZ207G Peak AC, DC 200 V Peak AC, DC 2 A 48 V AC
100 V DC
120, 240 V AC
AQZ206G2 Peak AC, DC 600 V Peak AC, DC 1 A
200, 400 V DC