JIS
JAPANESE
INDUSTRIAL
STANDARD
Translated and Published by
Japanese Standards Association
JIS A 4111:
(SSDA/JSA)
Solar water heater
ICS 27.160
Reference number : JIS A 4111: 2011 (E)
PROTECTED BY COPYRIGHT 24SA4111: 2011
Date of Establishment: 1979-01-01
Date of Revision: 2011-02-21
Date of Public Notice in Official Gazette: 2011-02-21
Investigated by: Japanese Industrial Standards Committee
Standards Board
‘Technical Committee on Architecture
JIS A 4111-2011, First English edition published in 2012-07
Translated and published by: Japanese Standards Association
4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN
In the event of any doubts arising as to the contents,
the original JIS is to be the final authority.
sd. Unless otherwise specified, no part of this publication may be reproduced or
utilized in any form or by any means, electronic or mechanieal, including photocopying and
‘microfilm, without permission in writing from the publisher,
Printed in Japan
NHIAT
PROTECTED BY COPYRIGHT5.2
5.3
5A
5.5
61
6.2
6.3
9.10
9.11
9.12
9.13
10
A4111: 2011
Contents
Scope
Normative references «
‘Terms and definitions
‘Types and names of individual parts ~~
‘Types
Names of individual parts
Materials ---eeveernrsen
Materials to be used for heat collecting body, cistern, hot water storage
tank and heat collecting hot water storage tank -
Materials to be used for the exterior box -~
Materials to be used for the transmission body
Materials to be used for the connecting pipe
Heat insulating materials to be used for the heat collecting part and
the hot water storage part ~.
Structure -
General
Ball tap -
Air gap between discharge opening of ball tap and overflow pipe
Performance--.-
Appearance
‘Tests -
Heat collecting performance test:
Heat insulating performance test.
Pressure resistance test
Freezing resistance test -
Blank heating resistance test -
Hot water supply performance test ~
Strength tests- so
Adhesion test ~
Salt spray test.
Durability test of exterior plasties
Durability test of transmission body -
Durability test of reflector body
Leaching performance test
+28
-30
Appearance test
@
PROTECTED BY COPYRIGHTA 4111: 2011
1L
wl
11.2
12
12.1
12.2
Annex A (informative) Indoor test method for heat collecting performance
Inspections -~
‘Type inspection
Delivery inspection ----srsnsnentnsennnnnneanennennnnennnnennennnnanneness BB
Marking. :
Information to be marked on the product
Information to be given on attached data
Annex B (informative) Comparison table between previous and current
editions of this Standard on technically significant
revisions --
Gi)
PROTECTED BY COPYRIGHTA4111: 2011
Foreword
This translation has been made based on the original Japanese Industrial Standard
revised by the Minister of Economy, Trade and Industry, through deliberations at
the Japanese Industrial Standards Committee as the result of proposal for revision
of Japanese Industrial Standard submitted by Solar System Development Association
(SSDA)/Japanese Standards Association (JSA) with the draft being attached, based
on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable
to the case of revision by the provision of Article 14.
Consequently JIS A 4111:1997 has been replaced with this Standard.
However, JIS A 4111:1997 may be applied in the JIS mark certification based on
the relevant provisions of Article 19 Clause 1, ete. of the Industrial Standardization
Law until August 20th, 2011.
This JIS document is protected by the Copyright Law.
Attention is drawn to the possibility that some parts of this Standard may conflict
with a patent right, application for a patent after opening to the public or utility
model right, The relevant Minister and the Japanese Industrial Standards Committee
are not responsible for identifying the patent right, application for a patent after
opening to the public or the utility model right.
Gi)
PROTECTED BY COPYRIGHTJAPANESE INDUSTRIAL STANDARD SIS A 4111: 2011
Solar water heater
1 Scope
‘This Japanese Industrial Standard specifies the solar water heaters (hereafter re-
ferred to as the “water heaters”) to be installed at a height of 10 m or less from the
ground surface level, which are mainly used for the hot water supply of detached
housings.
‘The comparison table between previous and current editions of this Standard con-
cerning the revised matters is given in Annex B.
2 Normative references
‘The following standards contain provisions which, through reference in this text,
constitute the provisions of this Standard. ‘The most recent editions of the standards
indicated below (including amendments) shall be applied
JIS A 1415 Methods of exposure to laboratory light sources for polymeric material
of buildings
JIS A 9504 Man made mineral fibre thermal insulation materials
JIS A 9511. Preformed cellular plastics thermal insulation materials
JIS A 9521 Man made mineral wool thermal insulation materials for dwellings
JIS B 1501 Rolling bearings—Balls
JIS B 2061 Faucets, ball taps and flush valves
JIS B 2301 Screwed type malleable cast iron pipe fittings
JIS B 2302 Screwed type steel pipe fittings
JIS B 8410. Pressure reducing valves for water works
JIS B 8414 Relief valves for hot water appliances
JIS G 3131 Hot-rolled mild steel plates, sheet and strip
JIS G 3141 Cold-reduced carbon steel sheet and strip
JIS G 3302 Hot-dip zine-coated steel sheet and strip
JIS G 8312 Prepainted hot-dip zine-coated steel sheet and strip
JIS G 3313 Electrolytic zine-coated steel sheet and strip
JIS G 3314 Hot-dip aluminium-coated steel sheet and strip
JIS G 8317 Hot-dip zinc—5 % aluminium alloy-coated steel sheet and strip
JIS G 3318 Prepainted hot-dip zinc—5 % aluminium alloy-coated steel sheet and
strip
JIS G 3320 Coated stainless steel sheets
JIS G 3321 Hot-dip 55 % aluminium-zine alloy-coated steel sheet and strip
JIS G 3322 Prepainted hot-dip 55 % aluminium—Zine alloy-coated steel sheet and
strip
PROTECTED BY COPYRIGHT