Professional Documents
Culture Documents
Dragonlock Miniature Holder Instr
Dragonlock Miniature Holder Instr
Welcome to the DRAGONLOCK: Ultimate™ terrain system. This instruction manual will outline some
basic materials you will need for 3D printing these models, specific printing information for the models in
this set, and links to additional resources.
For more information on getting started with 3D printing, help with choosing a printer, settings for many
popular printers, troubleshooting, and more; please visit our 3D Printer Facebook group:
https://www.facebook.com/groups/528423924186756/
For painting tutorials on these and other models in the DRAGONLOCK: Ultimate™ product line, please
visit our Youtube channel:
https://www.youtube.com/channel/UC5Lbnd97HV3rU98gcwHklzQ
https://www.youtube.com/channel/UC5Lbnd97HV3rU98gcwHklzQ
https://www.facebook.com/groups/528423924186756/
http://fatdragongames.proboards.com
Before inserting a Dragonbite™ clip, you must first remove the printing support present in each slot on all four sides of every
model. We recommend using needle-nose pliers to gently twist the support out of place (always wear eye protection when using
tools.) Clips should be printed with 15-20% infill (but can be printed with 0%.)
To connect DRAGONLOCK™ Ultimate models together, simply insert a Dragonbite™ clip into the slot of one model, then slide
the adjoining model into the opposite side. In addition to the standard v3.0 clip, there is an optional thinner clip included. If your
clips are still too tight vertically, just scale them down a few % on the Z AXIS ONLY in your slicer.
Printing info:
Filament:
•We recommend using PLA (we use eSun PLA Pro and Hatchbox PLA in the FDG office)
Layer Height:
•All models: 200 micron/.2mm
Top/Bottom layers:
•5 layers or 1 mm
Infill:
•5-10 (15-20% for clips)
Rafts:
•None
Brim:
•None (you may need it for the ‘Neck’ pieces if you have poor bed adhesion)
DRAGONLOCK™, DRAGONLOCK: Ultimate™, and Dragonbite™ are trademarks of Fat Dragon Games. @2020 Fat Dragon Games. All rights reserved.
For more information please visit: www.fatdragongames.com
1: before gluing the two parts of the handle together, 2: Glue the halves together.
we recommend filling the bottom with something
to add weight (pennies, modeling clay, sand, etc.)
3: Use a Dragonbite clip to attach the various sized 4: After printing the three pieces of each top sec-
top sections to your base. tion, make sure they are clean of any stringing that
might interfere with the sliding of the parts when
assembled. We recommend dry-fitting them before
any glue is applied to ensure they work as intended.
5: Slide the top section with the push bar onto the 6: Apply the non-moving top section over the glue
rail of the neck piece as shown. DO NOT GLUE and press down firmly, keeping pressure on it for
THIS PART, it must move once completed. Once a minute while the superglue sets. With your free
on, carefully put a drop of super glue in the three hand ensure the movable top section still slides
spots shown, being careful no glue comes near the freely and did not get glue on it.
sliding section.
7: Once fully dry, apply a thin rubber band to the 8: The three different sizes of top assemblies (for 1”,
assembly as depicted above. 1.5” and 2” miniature bases) can now be swapped
out on the handle using the Dragonbite clip to con-
nect them.
Bonus Ring Palette
Glue the ring to the palette as shown. We recommend applying a gloss clear coat (or two)
to seal the palette and make it easier to clean.