Professional Documents
Culture Documents
3ME - Technical Catalogue
3ME - Technical Catalogue
Technical Catalogue
E0.130.0219.02.00IM04
GEAR MOTORS “E” - “B” - “C” SERIES
Aluminium Body General Features
GEAR MOTORS
•Displacements from 2.8 cm3/rev to 73.4 cm3/rev (from 0.17 cu.in./rev to 4.48 cu.in./rev).
•Rated pressure up to 250 bar (3625psi).
•Speed up to 4500 rpm.
•Flanges, shafts and ports for ISO, DIN and SAE standards.
•Available in uni and bi-directional version for all the sizes, displacements and configurations.
•High volumetric efficiency thanks to an innovative design and an accurate control of machining tolerances.
•Axial compensation achieved by the use of floating bushes that allow high volumetric efficiency throughout the
working pressure range.
•DU bearings to ensure high pressure capability.
•12 teeth integral gear and shaft.
•Aluminium body.
•Cast iron flange and cover.
•Double shaft seals in all motor series. The one which faces the internal side is reinforced.
•Nitrile seals as standard and Viton seals in high temperature applications.
•Available with different valves and circuit configurations built-in rear cover.
•All motors are hydraulically tested after assembly to ensure the highest standard performance.
WORKING CONDITIONS
DEFINITION OF PRESSURES
www.salami.it 131
GEAR MOTORS “E” - “B” - “C” SERIES
General Features Aluminium Body
DRIVE SHAFTS
Radial and axial loads on the shafts must be avoided since they reduce the life of the unit.
In order to avoid misalignment during the assembly with the primary engine, a connection with “Oldham” coupling (or
coupling having convex toothed hub) is recommended.
ROTATION
E0.100.0821.02.00IM03
HYDRAULIC PIPE
HYDRAULIC PIPE LINE
LINE
To calculate hydraulic pipe line size, the designer can use; as an approximate guide, the following fluid speed figures:
From 6 to 10 m/sec on pressure pipe line From 19.7 to 32.8 ft/sec on pressure pipe line
The lowest fluid speed values in pipe lines is recommended when the operating temperature range is high and/or for
continuous duty.
The highest value is recommended when the temperature difference is low and/or for intermittent duty.
In case of reversible motor allowance must be made to ensure the motor is not drained, through the case drain, when
stationary.
132 www.salami.it
GEAR MOTORS “E” - “B” - “C” SERIES
Aluminium Body General Features
IDENTIFICATION LABEL
E0.100.0821.02.00IM03
Rot.
Unit Rotation
Build Order Number
(for Salami management)
www.salami.it 133
GEAR MOTORS “E” - “B” - “C” SERIES
General Features Aluminium Body
TECHNICAL DATA
GROUP 2.5 - B SERIES cm3/rev cu.in/rev bar psi bar psi rpm
2.5MB - 16 16 0.97 250 3625 280 4060 3000 600
2.5MB - 19 19.3 1.17 250 3625 280 4060 3000 600
2.5MB - 22 22.2 1.35 250 3625 280 4060 3000 500
2.5MB - 25 25.2 1.53 250 3625 280 4060 3000 500
2.5MB - 28 27.6 1.68 250 3625 280 4060 3000 500
2.5MB - 32 32.4 1.97 230 3330 250 3625 3000 500
2.5MB - 38 38.1 2.32 200 2900 220 3190 2750 400
2.5MB - 44 44.2 2.69 170 2465 190 2755 2500 400 E0.100.0821.02.00IM03
Pin Pin
Pdrain 20 bar The Motors are equipped with HPD shaft seal (20bar),
(290 psi) on request is available also for motor with outrigger bearing.
Max drain pressure is influenced by rotational speed of the unit.
Pout 20 bar Pout Pin
(290 psi)
134 www.salami.it
GEAR MOTORS “E” SERIES
Aluminium Body 3ME
INDEX
www.salami.it 193
GEAR MOTORS “E” SERIES
Aluminium Body 3ME
3ME
E0.130.0219.02.00IM05
www.salami.it 195
GEAR MOTORS “E” SERIES
3ME Aluminium Body
Type 27 33 38 46 55 65 75
cm /rev
3
27 33.5 38.7 46.9 54.1 63.1 73.4
Displacement
cu.in./rev 1.65 2.04 2.36 2.86 3.3 3.85 4.48
mm 79 84 88 104 110 117 124
Dimension A
in 3.11 3.31 3.46 4.09 4.33 4.61 4.88
mm 39.5 42 44 52 55 58.5 62
Dimension C
in 1.56 1.65 1.73 2.05 2.17 2.30 2.44
Max
bar 250 250 250 250 220 200 180
continuous P1
psi 3625 3625 3625 3625 3190 2900 2610
pressure
Max starting bar 280 280 280 270 240 220 200
P2
pressure psi 4060 4060 4060 3915 3480 3190 2900
Max speed rpm 3000 3000 2750 2750 2500 2500 2500
Min speed rpm 600 600 500 500 400 400 400
95-105 Nm
22 32.5 (70-77.4 lbf∙ft)
.87 A 1.28
5 19
.20 C
E0.130.0219.02.00IM05
.87
22
Body width
196 www.salami.it
GEAR MOTORS “E” SERIES
Aluminium Body 3ME
ASSEMBLING DIMENSIONS
Type 46 55 65 75
cm /rev
3
46.9 54.1 63.1 73.4
Displacement
cu.in./rev 2.86 3.3 3.85 4.48
mm 104 110 117 124
Dimension A
in 4.09 4.33 4.61 4.88
mm 52 55 58.5 62
Dimension C
in 2.05 2.17 2.30 2.44
kg 10.1 10.5 10.8 11.2
Weight
lbs 22.3 23 23.8 24.6
95-105 Nm
22 32.5 (70-77.4 lbf∙ft)
.87 A 1.28 136.2
5.36
5 19
.20 C 114.2
4.50
60.3
2.37
49.3
1.94
.87
22
149.3
5.88
4.37
111
Tapered 1:8
E0.130.0219.02.00IM05
O 11
.43
www.salami.it 197
GEAR MOTORS “E” SERIES
3ME Aluminium Body
code P BI-DIRECTIONAL
MOTORS
ØD ØA d e ØD ØA d e
19 40 19 40
27 M8 M8
Flanged ports (0.75”) (1.57”) (0.75”) (1.57”)
16 16
european standard
(0.63”) (0.63”)
From 33 27 51 27 51
M10 M10
to 75 (1.06”) (2.01”) (1.06”) (2.01”)
code B
Flanged ports
german standard
E0.130.0219.02.00IM05
Flanged ports
SAE J518
METRIC THREAD
198 www.salami.it
GEAR MOTORS “E” SERIES
Aluminium Body 3ME
code S
Flanged ports
SAE J518
AMERICAN STANDARD
THREAD
1-1/16-12 1-1/16-12
From 21 41 21 41
Threaded ports 27 to 38
UN
(0.83”) (1.61”)
UN
(0.83”) (1.61”)
SAE (ODT) (SAE 12) (SAE 12)
19 3.3 19 3.3
1-5/16-12 (0.75”) (0.12”) 1-5/16-12 (0.75”) (0.13”)
From 25 49 25 49
UN UN
46 to 75 (0.98”) (1.93”) (0.98”) (1.93”)
(SAE 16) (SAE 16)
www.salami.it 199
GEAR MOTORS “E” SERIES
3ME Aluminium Body
DRIVE SHAFTS
code 35 Max torque 260 Nm (2300 lbf in) code 38 Max torque 250 Nm (2213 lbf in) code 48 Max torque 350 Nm (3100 lbf in)
European tapered 1:5 European tapered 1:8 European tapered 1:8 for 3.5PC
[0.984]
Ø25
code 55 Max torque 330 Nm (2921 lbf in) code 56 Max torque 480 Nm (4250 lbf in)
SAE B 13T-16/32DP Ansi B92 1a 1976 SAE BB 15T-16/32DP Ansi B92 1a 1976
E0.130.0219.02.00IM05
Mounting face
Mounting face
code 87 Max torque 220 Nm (1950 lbf in) code 88 Max torque 320 Nm (2830 lbf in)
200 www.salami.it
GEAR MOTORS “E” SERIES
Aluminium Body 3ME
MOUNTING FLANGES
www.salami.it 201
GEAR MOTORS “E” SERIES
3ME Aluminium Body
OUTRIGGER BEARING
TYPE H
27 79 (3.11”)
33 84 (3.31”)
Fr
38 88 (3.46”) L=Distance between
46 104 (4.09”) mounting flange and
55 110 (4.33”)
radial force point of
65 117 (4.61”)
application.
Example:
Fr = 3000 N
L = 35 Expected life: 1000 hrs
Speed = 2500 rpm
For Code CP
E0.130.0219.02.00IM05
For Code CSB
202 www.salami.it
GEAR MOTORS “E” SERIES
Aluminium Body 3ME
CSB SAE B
www.salami.it 203
GEAR MOTORS “E” SERIES
3ME Aluminium Body
REAR COVERS
E0.130.0219.02.00IM05
A B A C
G1 G3/4 G3/4 G3/8
1-5/16-12 UN-2B 1-1/16-12 UN-2B 1-1/16-12 UN-2B 9/16-18 UN-2B
(SAE16) (SAE12) (SAE12) (SAE6)
204 www.salami.it
GEAR MOTORS “E” SERIES
Aluminium Body 3ME
PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C
200 bar
Power [KW]
60.00 60.00
20.00
150 bar
50.00
15.00
40.00 40.00
100 bar
30.00 10.00
20.00 20.00 50 bar
5.00
10.00
0.00
0.00 0.00
0 1000 RPM 2000 3000
0 1000 2000 3000
RPM
3ME - 27
100.00
80.00
Power [KW]
200 bar
25.00
Flow [l/min]
80.00
60.00 20.00
150 bar
60.00
15.00
40.00
100 bar
40.00
10.00
20.00 50 bar
20.00 5.00
3ME - 33
E0.130.0219.02.00IM05
30.00
Power [KW]
100.00
Flow [l/min]
3ME - 38
www.salami.it 205
GEAR MOTORS “E” SERIES
3ME Aluminium Body
PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C
Output torque / Power
Output torque/power
160.00
180.00 60.00
140.00 160.00
250 bar 50.00
120.00 140.00
Power [KW]
Flow [l/min]
100.00
80.00 150 bar 30.00
80.00
60.00 100 bar
60.00 20.00
40.00
40.00
50 bar 10.00
20.00 20.00
3ME - 46
Output torque / Power
Output torque/power
160.00
180.00 45.00
140.00 160.00 40.00
220 bar
120.00 140.00 35.00
Output torque [Nm]
180 bar
120.00 30.00
Power [KW]
100.00
Flow [l/min]
150 bar
100.00 25.00
80.00
80.00 20.00
60.00 100 bar
60.00 15.00
40.00
40.00 50 bar 10.00
20.00 20.00 5.00
3ME - 55
E0.130.0219.02.00IM05
Output torque / Power
Output torque/power
180.00
200.00 50.00
160.00 180.00 45.00
200 bar
140.00 160.00 40.00
Output torque [Nm]
100.00
120.00 30.00
100.00 25.00
80.00 100 bar
80.00 20.00
60.00
60.00 15.00
50 bar
40.00
40.00 10.00
20.00 20.00 5.00
0.00 0.00 0.00
0 1000 RPM 2000 0 1000 2000
RPM
3ME - 65
206 www.salami.it
GEAR MOTORS “E” SERIES
Aluminium Body 3ME
PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C
Output torque / Power
Output torque/power
180.00
180.00 45.00
160.00
160.00 40.00
180 bar
140.00
140.00 35.00
Power [KW]
Flow [l/min]
3ME - 75
E0.130.0219.02.00IM05
www.salami.it 207
GEAR MOTORS “E” SERIES
How to order-3ME Aluminium Body
SINGLE MOTORS
A B C D E F G H
3ME
Order example: 3ME 46D, ports SAE (R), drive shaft (56),
mounting flange (S3)
3ME46D-R56S3
208 www.salami.it
www.salami.it
You can find our most up to date “STANDARD SALES CONDITIONS” on our website.
Potete trovare le nostre più aggiornate “CONDIZIONI DI VENDITA STANDARD” sul nostro sito.
www.salami.it