Professional Documents
Culture Documents
Technical Catalogue
E0.130.0417.02.00IM03
GEAR PUMPS “E”- “B”- “C” SERIES
Aluminium Body General Features
GEAR PUMPS
SALAMI gear pumps are available with displacements from 1.4 cm3/rev to 99 cm3/rev (from 0.09 cu.in/rev to 6.03
cu.in/rev).
Multiple pumps can always be relized combining stages taken from different or same series.
Several options of shafts, flanges and ports as for European, German and American standards are available for all
the pumps.
TECHNICAL DATA
- Hydraulic fluid
GEAR PUMP mineral oil
“PG” SERIES on request.
*Available
End
Features
plate
DEFINITION OF PRESSURES
DEFINITION OF PRESSURES
P3 = Peak
P3 =pressure
Peak pressure
P2 = Intermittent
P2 = Intermittent operating
operating pressurepressure (1/3 of working
(1/3 of working time) time)
P1 = Continuous operating pressure
P1 = Continuous operating pressure
max. 20 s
GENERAL
DRIVE SHAFTS
Radial and axial loads on the shafts must be avoided since they reduce the life of the unit.
In order to avoid misalignment during the assembly with the primary engine, a connection with “Oldham” coupling (or
coupling having convex toothed hub) is recommended.
ROTATION
To ensure favorable suction conditions it is important to keep pressure drop in suction pipe line to a minimum value
(see TECHNICAL DATA).
To calculate hydraulic pipe line size, the designer can use; as an approximate guide, the following fluid speed figures:
From 1 to 2 m/sec on suction pipe line From 3.28 to 6.36 ft/sec on suction pipe line
From 6 to 10 m/sec on pressure pipe line From 19.7 to 32.8 ft/sec on pressure pipe line
The lowest fluid speed values in pipe lines is recommended when the operating temperature range is high and/or for
continuos duty.
The highest value is recommended when the temperature difference is low and/or for intermittent duty.
When tandem pumps are supplied by 2 different reservoirs with 2 different fluids it is necessary to specify “AS”
version.
6 www.salami.it
GEAR PUMPS “E”- “B”- “C” SERIES
Aluminium Body General Features
IDENTIFICATION LABEL
E0.100.0417.02.00IM01
WO0132803
www.salami.it 7
GEAR PUMPS “E”- “B”- “C” SERIES
General Features Aluminium Body
WORKING CONDITIONS
GROUP 2 - E SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
2PE - 3.2* 3.2 0.19 250 3625 280 4060 300 4350 4000 600
2PE - 3.9* 3.9 0.24 250 3625 280 4060 300 4350 4000 600
2PE - 4.5 4.6 0.27 250 3625 280 4060 300 4350 4000 600
2PE - 6.5 6.5 0.4 250 3625 280 4060 300 4350 4000 600
2PE - 8.3 8.2 0.5 250 3625 280 4060 300 4350 3500 500
2PE - 10.5 10.6 0.65 250 3625 280 4060 300 4350 3500 500
2PE - 11.3 11.5 0.68 250 3625 280 4060 300 4350 3500 500
2PE - 12.5 12.7 0.77 250 3625 280 4060 300 4350 3500 500
2PE - 13.8 13.8 0.84 250 3625 280 4060 300 4350 3500 500
2PE - 16 16.6 1.01 250 3625 280 4060 300 4350 3000 400
2PE - 19 19.4 1.15 220 3190 240 3480 260 3750 3000 400
2PE - 22.5 22.9 1.37 200 2900 220 3190 240 3480 2750 400
2PE - 26 25.8 1.58 180 2610 200 2900 220 3190 2500 400
*Available only as rear pump
GROUP 2.5 - B SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
2.5PB - 5.5* 5.97 0.36 250 3625 280 4060 300 4350 3000 600
E0.100.0417.02.00IM01
2.5PB - 8.3* 8.29 0.50 250 3625 280 4060 300 4350 3000 600
2.5PB - 11.5* 11.76 0.72 250 3625 280 4060 300 4350 3000 600
2.5PB - 13.8* 14.07 0.86 250 3625 280 4060 300 4350 3000 600
2.5PB - 16 16 0.97 250 3625 280 4060 300 4350 3000 600
2.5PB - 19 19.3 1.17 250 3625 280 4060 300 4350 3000 600
2.5PB - 22 22.2 1.35 250 3625 280 4060 300 4350 3000 500
2.5PB - 25 25.2 1.53 250 3625 280 4060 300 4350 3000 500
2.5PB - 28 27.6 1.68 250 3625 280 4060 300 4350 3000 500
2.5PB - 32 32.4 1.97 230 3335 250 3625 260 3750 3000 500
2.5PB - 38 38.1 2.32 200 2900 220 3190 240 3480 2750 400
2.5PB - 44 44.2 2.69 170 2465 190 2755 210 3040 2500 400
*Available only as rear pump. Displacements 11.5-13.8 are available as single pump only with drive shaft “55”.
8 www.salami.it
GEAR PUMPS “E”- “B”- “C” SERIES
Aluminium Body General Features
GROUP 3.5 - C SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
3.5PC - 55 54.8 3.34 250 3625 280 4060 300 4350 2750 400
3.5PC - 64 63.2 3.85 250 3625 280 4060 300 4350 2750 350
3.5PC - 75 74.7 4.55 230 3335 250 3625 280 4060 2500 300
3.5PC - 87 88 5.36 210 3040 230 3330 260 3750 2250 300
3.5PC - 98* 99 6.03 200 2900 220 3190 250 3625 2000 300
*Displacement 98 are special release, please contact sales department.
**For working conditions, using exclusively pressure P1, the value of max. speed must be reduced of 10%.
The max pressure is refered to pumps with flanged ports, using the threaded ports the pump life could be
reduced.
E0.100.0417.02.00IM01
www.salami.it 9
GEAR PUMPS “E”- “B”- “C” SERIES
General Features Aluminium Body
Before starting, be sure that the pump is cleaned externally as well as the working area to avoid that particles
dangerous for pump working can find their way into the pump. Pump represented is a clockwise rotation pump.
To obtain an anti_clockwise rotation read carefully the following instructions.
1 - Draw out the driven gear from its housing, taking care to avoid
rear cover axial shifts.
2 - Re-locate the driven gear in the position previously occupied by
the driving gear.
10 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
INDEX
www.salami.it 89
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
3PE
E0.130.0417.02.00IM03
www.salami.it 91
GEAR PUMPS “E” SERIES
3PE Aluminium Body
Max speed at P2 rpm 3000 3000 3000 2750 2750 2500 2500 2500
Min speed at P1 rpm 600 600 600 500 500 400 400 400
95-105 Nm
22 32.5 (70-77.4 lbf∙ft)
.87 A 1.28
5 19
.20 C
E0.130.0417.02.00IM03
.87
22
Body width
Ø 2.000
92 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
ASSEMBLING DIMENSIONS
Type 46 55 65 75*
95-105 Nm
22 32.5 (70-77.4 lbf∙ft)
.87 A 1.28 136.2
5.36
5 19
.20 C 114.2
4.50
60.3
2.37
49.3
1.94
.87
22
149.3
5.88
4.37
111
Tapered 1:8
E0.130.0417.02.00IM03
O 11
.43
www.salami.it 93
GEAR PUMPS “E” SERIES
3PE Aluminium Body
E0.130.0417.02.00IM03
94 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
Threaded ports
GAS (BSPP)
E0.130.0417.02.00IM03
1-5/16-12 1-1/16-12
From 25 49 21 41
UN UN
21 to 38 (0.98”) (1.93”) (0.83”) (1.16”)
(SAE 16) (SAE 12)
19 3.3 19 3.3
1-5/8-12 (0.75”) (0.12”) 1-5/16-12 (0.75”) (0.13”)
From 27 58 25 49
UN UN
46 to 75 (1.06”) (2.28”) (0.98”) (1.93”)
(SAE 20) (SAE 16)
code R
BI-DIRECTIONAL PUMPS Special version available on request.
Threaded ports
SAE (ODT)
www.salami.it 95
GEAR PUMPS “E” SERIES
3PE Aluminium Body
DRIVE SHAFTS
code 35 Max torque 260 Nm (2300 lbf in) code 38 Max torque 250 Nm (2213 lbf in) code 48 Max torque 350 Nm (3100 lbf in)
European tapered 1:5 European tapered 1:8 European tapered 1:8 for 3.5PC
[0.984]
Ø25
code 55 Max torque 330 Nm (2921 lbf in) code 56 Max torque 480 Nm (4250 lbf in) code 65 Max torque 280 Nm (2478 lbf in)
E0.130.0417.02.00IM03
code 87 Max torque 220 Nm (1950 lbf in) code 88 Max torque 320 Nm (2830 lbf in)
96 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
MOUNTING FLANGES
www.salami.it 97
GEAR PUMPS “E” SERIES
3PE Aluminium Body
OUTRIGGER BEARING
TYPE H Fr
27 79 (3.11”)
33 84 (3.31”)
38 88 (3.46”) L=Distance between
46 104 (4.09”) mounting flange and
55 110 (4.33”)
radial force point of
65 117 (4.61”)
application.
Example:
Fr = 3000 N
Expected life: 1000 hrs
L = 35
Speed = 2500 rpm
For Code CP
E0.130.0417.02.00IM03
For Code CSB
98 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
CSB SAE B
www.salami.it 99
GEAR PUMPS “E” SERIES
3PE Aluminium Body
REAR COVER
external drain
DIMENSION C
Standard rear cover Standard rear cover
for unidirectional pumps for reversible pumps, with external drain C.
For the dimension C please see the table here below
C
G3/8
9/16-18 UNF-2B (SAE6)
E0.130.0417.02.00IM03
Outlet Inlet
DIMENSION B DIMENSION A
code 1
For pumps with threaded rear ports, suitable up to 80 l/min delivery.
A B
G1 G3/4
1-5/16-12 UN-2B 1-1/16-12 UN-2B
(SAE16) (SAE12)
100 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
PRIORITY VALVES
6°
Inlet
LS - Signal inlet
The double or triple pumps can be configurated with priority flow valve too.
The stage which has its flow divided into priority and exceeded flows is always the back one.
EF CF
EF CF
www.salami.it 101
GEAR PUMPS “E” SERIES
3PE Aluminium Body
VP1 - VPS1
SIDE PORTS
AXIS OF PUMP SHAFT
68.5 48 ANTI-CLOCKWISE ROTATION
2.70 1.89
59,9
2,4
2,5
64
59,9
E0.130.0417.02.00IM03
2,4
2,5
64
64
2,5
A D E
G 3/8 G 3/4 G 1/4
SAE8 SAE12 SAE4
3/4 - 16 UNF - 2B 1-1/16 - 12 UN - 2B 7/16 - 20 UNF - 2B
102 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
MULTIPLE MULTIPLE
GEAR PUMPS GEAR PUMPS
with inlet port with common
on each body inlet port*
*In case of common inlet port, to avoid too
high value of oil speed, 60 l/min is the max
sucked flow for the downstream pump.
59.9
2.36
.87
22
Max. torque
3.62
280 Nm 92
(2921 lbf in)
E0.130.0417.02.00IM03
14.5
n.2 holes O .57
Front pump Rear pump
This is a Salami standard pump, These units are pre-arranged for multiple
alla drive shafts have a splined end. pumps, they have the drive shaft code 64.
www.salami.it 103
GEAR PUMPS “E” SERIES
3PE Aluminium Body
MULTIPLE PD2
GEAR PUMPS Max. torque 58 - 62
with inlet port (42.8 - 45.7 lbf∙ft)
on each body
MULTIPLE
GEAR PUMPS
with common
inlet port*
*In case of common inlet port, to avoid too high
value of oil speed, 30 l/min is the max sucked
flow for the downstream pump or pumps.
2PE-Type 3.2* 3.9* 4.5 6.5 8.3 10.5 11.3 12.5 13.8 16 19 22.5 26
PD1.5 95 - 105 Nm
(70 - 77.4 lbf-ft)
E0.130.0417.02.00IM03
30 Nm
(22.1 lbf-ft)
23 - 28 Nm
(16.9 - 20.6 lbf-ft)
1.5PE-Type 1.4 2.1 2.8 3.5 4.1 5.2 6.2 7.6 9.3 11
104 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C
40.00
70.00
Power
35.00
Flow rate [l/min] 20 bar [kW] 50
Flow rate [l/min] 300 bar bar
r
ba
Power
60.00 [kW] 100
0
ba
30
bar
Power
20
[kW] 150
bar
30.00
r
ba
r
ba
0
25
50.00
0
25
25.00
r
ba
20.00
ar
30.00 0b
15
15.00
bar
20.00 100
10.00
r
50 ba
10.00
5.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 3500
0 800 1600 2400 3200
RPM RPM
3PE-21
90.00 Powe
Powe
Powe
Powe
80.00
Powe
r
ba
Powe
20
Flow rate r
ba
0
0
30
E0.130.0417.02.00IM03
60.00
40.00
r
ba
0
25
35.00
Flow rate [l/min]
50.00
ar
30.00 0b
20
Input power [kW]
40.00
25.00
ar
0b
15
30.00
20.00
bar
15.00 100
20.00
10.00
r
50 ba
10.00
5.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 3500 0 800 1600 2400 3200
RPM RPM
3PE-27
www.salami.it 105
GEAR PUMPS “E” SERIES
3PE Aluminium Body
PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C
60.00
120.00
r
ba
0
30
Flow rate [l/min] 20 bar
r
ba
ba
0
20
25
r
ba 40.00
0
25
80.00
r
ba
0
20
Power [kW] 50 b
r
20.00 10.00 50 ba
0.00
0.00
0 500 1000 1500 2000 2500 3000 3500
0 400 800 1200 1600 2000 2400 2800 3200
RPM
RPM
3PE-33
60.00
120.00
r
ba
0
28
bar
20
25
Power [kW]
bar
Power [kW]
r
bar
ba
0
r
24
40.00 ba E0.130.0417.02.00IM03
80.00 0
20
Input power [kW]
Flow rate [l/min]
30.00 ar
60.00 0b
15
20.00 bar
40.00 100
r
10.00 50 ba
20.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM
3PE-38
106 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE
PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C
140.00 70.00
r
ba
0
28
Flow rate [l/min] 20 bar
120.00 60.00
r
ba
ba
Flow rate [l/min] 280 bar
20
0
25
r
ba
0
25
P
100.00 50.00
e
r
ba [k
0 5
20 b
80.00
ar
0b
15
60.00 30.00
bar
100
40.00 20.00
r
50 ba
20.00 10.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM
3PE-46
140.00 70.00
Power [kW] 40 bar
Power [kW] 80 bar
r
ba
ar
120.00
r
60.00
ba
25
50.00
20
E0.130.0417.02.00IM03
r
ba
0
16
Flow rate [l/min]
80.00 40.00
Input power [kW]
r
ba
60.00 30.00 0
12
r
ba
40.00 20.00 80
r
40 ba
20.00 10.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM
RPM
3PE-55
www.salami.it 107
GEAR PUMPS “E” SERIES
3PE Aluminium Body
PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C
80.00
160.00
Flow rate Power [kW] 40
r
[l/min] 20 bar bar
ba
r
70.00
ba
Power [kW] 80
20
0
bar
24
140.00 Power [kW] 120
ar
0b
bar
20
60.00
r
ba
120.00
0
20
50.00
r
100.00 ba
0
16
40.00
80.00
ar
0b
12
30.00
60.00
bar
80
20.00
40.00
r
40 ba
20.00 10.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM
3PE-65
80.00
180.00
ar
0b
22
r
ba
70.00
ar
20
0b
160.00
18
r
ba
140.00 60.00
5
17
120.00 E0.130.0417.02.00IM03
50.00 r
ba
0
Flow rate [l/min] 20 bar 12
Input power [kW]
Flow rate [l/min]
30.00
60.00 bar
70
20.00
40.00
r
35 ba
10.00
20.00
0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM
3PE-75
108 www.salami.it
GEAR PUMPS “E” SERIES
Aluminium Body 3PE-How to order
SINGLE PUMPS
Adjustable flow l/min
A B C D E F G H I L
3PE 33 D - P 38 P2 - V - 1 - CP - PD2 - VP1 ... / ...
Setting main
relief valve (bar)
Order example 3PE 46D, ports SAE (R), drive shaft (56),
mounting flange (S3)
3PE46D-R56S3
www.salami.it 109
GEAR PUMPS “E” SERIES
How to order-3PE Aluminium Body
MULTIPLE PUMPS
Adjustable flow l/min
A B C D E F G H I L M
3PE 65 / 46 D - P 28 P2 - V UA - 1 - CP - PD2 - VPD1 ... / ...
Setting main
relief valve (bar)
Threaded ports
G
GAS (BSPP)
G SUCTION PORTS CODES
Threaded ports
R Common suction UA*
SAE (ODT)
Flanged ports Separeted stages AS
SAE J518 AMERICAN S
STANDARD THREAD F SEAL CODE
Flanged ports Buna standard
W
SAE J518 METRIC THREAD
Viton V
DRIVE SHAFT (page 96) CODES D
E MOUNTING FLANGES (page 97) CODES
European Tapered 1:5 35
SAE B 2 Bolts S3
European Tapered 1:8 38
European standard Ø50.8 P2
European Tapered 1:8 48 E0.130.0417.02.00IM03
European standard Ø60.3 P3
SAE B splined 13T 55
German standard Ø105 B6
SAE BB splined 15T 56
SAE B parallel 87
SAE BB parallel 88
Order example 3PE 33/27D, ports SAE (P), drive shaft (56),
mounting flange (S3)
3PE33/27D-R56S3
*UA: this type of multiple pump is a Salami standard multiple pump
which has only one inlet port opened, all the other inlet port are
closed.
In case of common suction, the code 1 - 2 or 3, correspond to the
body where inlet is located.
110 www.salami.it
You can find our most up to date “STANDARD SALES CONDITIONS” on our website.
www.salami.it
T. +39 059 387 411
sales@salami.it
www.salami.it