1. Pins 1 and 16 can connect an external 4-8 ohm speaker, but are not grounded. Pin 2 accepts external microphone audio input at 500 ohm impedance.
2. Pin 3 controls voice channel PTT by pulling the pin low according to software settings. It is connected to 3.3V through a 3.3k resistor.
3. Pins 4, 8, 12, and 14 are programmable inputs/outputs that require software to define their functions.
1. Pins 1 and 16 can connect an external 4-8 ohm speaker, but are not grounded. Pin 2 accepts external microphone audio input at 500 ohm impedance.
2. Pin 3 controls voice channel PTT by pulling the pin low according to software settings. It is connected to 3.3V through a 3.3k resistor.
3. Pins 4, 8, 12, and 14 are programmable inputs/outputs that require software to define their functions.
1. Pins 1 and 16 can connect an external 4-8 ohm speaker, but are not grounded. Pin 2 accepts external microphone audio input at 500 ohm impedance.
2. Pin 3 controls voice channel PTT by pulling the pin low according to software settings. It is connected to 3.3V through a 3.3k resistor.
3. Pins 4, 8, 12, and 14 are programmable inputs/outputs that require software to define their functions.
1 External Speaker (-) Connect a 4 or 8 ohm external speaker to 1 and 16 speakers.
Note: The internal circuit
is a bridge External speaker terminal type output, pin 1 or 16 are not grounded 2 External Mic Audio input impedance is 500 ohms. The modulation degree when the input is flattened at 1 kHz and the average is 80 Mv The external microphone input is 60%. When using this channel, the PTT should be defined appropriately through the programming software 3 External Mic PTT pulls this pin low (below 0.66 Vdc) and will back-fire, and according to the programming software Defines the voice channel of the phase-opening post (pin 2 or slave 5). when the user presses When the PTT is connected to the front panel, the socket will be lowered for the user to sense the external device. PTT operational status. This pin is connected to 3.3 Vdc through a 3.3k resistor 4 Programmable Programmable Active high when connected to 13.8 Vdc power supply Output Programmable output for current up to 0.25 amps 5 Flat_TX_Audio Input Input impedance: greater than 35k ohms. Modulation at an average input level of 150 mV Smooth transmission audio input degree is 60% 6 SCL radio software programming interface. If used as normal input control, in addition to and need to use programming software In addition to the corresponding definition of the programming interface, it is also necessary to remove the resistor R421 inside the bridge radio. 7 Ground 7" wire 8 Programmable I/O requires programming software to define the corresponding input or output functions. Programmable input answer 9 Emergency inpuT alarm check-in, it needs to be used with MDC1200 signaling Alarm input 10 Ignition Sense ignition sensitivity lighten up the lawsuit 11 Receiver audio Software selectable between two outputs: 660mV rms (de-emphasis/silence) or output 330mV rms (no de-emphasis/no clutter). Minimum load impedance 5k ohms 12 Programmable I/O GO requires programming software to define the corresponding input or output functions. 13 Switched B+ 13.8Vdc power supply controlled by the power switch (maximum current 500mA) 14 Programmable I/O Programmable IO requires programming software to define the corresponding input or output function. Programmable input and output 15 Internal Speaker One is connected to the positive terminal of the internal speaker, and the power is connected to the 16th slave through the internal cable. internal horn 16 External Speaker (+) Connect a 4 or 8 ohm external speaker to pins 1 and 16. Note: Internal circuit The positive terminal of the external speaker is a bridge type, and the 1 or 16 pins are not grounded.