Professional Documents
Culture Documents
Safety rules 2
Modifications 2
Construction 2
Installation 4
Maintenance 20
Appendices 22
High-Speed PVC
Fabric Doors of
SPEEDROLL series
with DOORHAN, GFA,
BMP drives
© DoorHan, 01.2019
1. GENERAL INFORMATION
GENERAL INFORMATION
The information contained in this manual will familiarize of the operator to comply with the instructions listed in
you with construction, operation and maintenance of this manual.
high-speed PVC fabric door (further — the product). We recommend that installation, operation and
The manufacturer does not directly control installation, maintenance be performed by a qualified technician.
operation and maintenance of the product. The operator The manufacturer reserves the right to modify the product
shall be held responsible for safe operation and without prior notice.
maintenance of the product. It shall be the responsibility
2. SAFETY RULES
ATTENTION!
Only trained personnel should operate or service this equipment!
Carefully follow the instructions provided in this manual when performing installation or operation of the doors.
Always maintain proper lighting in the work area. to clearly see the door when operating it. The control
Keep the work area clean of people and objects during unit shall always be kept closed.
installation and operation of the doors. Turn OFF electrical power before making any electrical
Install control unit at such a place that operator be able connections.
3. MODIFICATIONS
SpeedRoll doors with DoorHan drive are compatible SpeedRoll doors with GFA drive are compatible with
with control units of HSDC 181900, HSDC 18191, control units of TS 970 series (2 types).
HSDC 18192, HSDC 18193, HSDC 18191(N) series. SpeedRoll doors with BMP drive are compatible with
HSDC 18191(N) control unit is used with doors opened control units of HSD 1800, HSD 18001 series.
in emergency with counterbalance mechanizm.
4. CONSTRUCTION
Fig. 1. Standard (side drive)
6
2
3 7
9
5
10
2
Fig. 2. Standard (front drive)
CONSTRUCTION
1
6
2
3 7
4
8
9
5
10
11
1. Shaft box
2. Shaft
3. Electric drive
4. Door curtain
5. Control unit
6. Door curtain guide
7. Vertical track
8. Transparent insert (window)
9. Photocells
10. Bottom bar assembly
11. Counterbalance 3
4.1. SPECIFICATIONS
CONSTRUCTION
5. INSTALLATION
5.1. UNLOADING AND RECEIVING THE 5.2. GENERAL RULES
PRODUCT Make sure you observe all applicable safety regulations
Unload the product using a forklift or a crane. Make sure during installation of the product. We recommend that
installation of the product be performed by DoorHan
4
the components delivered correspond to the list provided
in Components Set section of the manual. service department or DoorHan dealer.
Check whether door dimensions correspond to opening
width, height, and diagonal before proceeding to Hammer
INSTALLATION
installation. Rotary hammer
Electric drill
5.3. LOADING EQUIPMENT Stone and metal bits for rotary hammer
Forklift: minimum load capacity — 35 kN; Multimeter
fork length — not less than 2,000 mm. Scissors
Crane, minimum lifting capacity — 20 kN. Wire cutters
Pliers
5.4. TOOLS Stepladder
Tape measure
Water level 5.5. OPENING DIMENSIONS
Set of screwdrivers W — opening width.
Set of wrenches (17, 13, 10 and 8 mm) H — opening height.
Hexagon set (17, 13, 10 and 8 mm)
190-210
500
1200
500
5
INSTALLATION
Fig. 3. Side drive, counterbalance
190-210
1200
500
500
1200
ATTENTION!
Maximum dimensions of the door assembled on a horiszontal surface and lifted with a forklift should not exceed
3,500 (W) × 3,500 (H) mm.
6 If door dimensions exceed the listed above figures install vertical tracks at first, than lift the door upper part, and fix it
to the vertical tracks and wall.
5.6.1. DOOR DIMENSIONS LESS THAN 3,500 × 3,500 MM
INSTALLATION
1. Place all door frame parts on a horizontal surface.
2. Dismantle tracks casing, shaft box and drive casing.
3. Fasten vertical tracks to shaft box with angles and screws.
4. Carefully raise assembled frame with a forklift and move it to the door opening.
5. Level all parts of the door frame with water level (put a pad under a track if necesssary).
6. Temporarily attach the frame (vertical tracks, shaft box) to the wall with fasteners.
7. Fix the shaft box and drive casing.
Fig. 1
Fig. 2
7
INSTALLATION
Fig. 3
Fig. 4
8
INSTALLATION
Fig. 5
9
INSTALLATION
Fig. 6
Fig. 7
10
INSTALLATION
Fig. 8
Fig. 8А
11
INSTALLATION
Fig. 9
Fig. 10
12
5.6.2. DOOR DIMENSIONS MORE THAN 3,500 × 3,500 MM
INSTALLATION
1. Place all door frame parts on a horizontal surface.
2. Dismantle tracks casing, shaft box and drive casing.
3. Level vertical tracks with water level (put a pad under a track if necesssary) and temporarily fix them to the wall with
fasteners.
4. Carefully raise the door upper part with a forklift and place it on vertical tracks.
5. Fasten vertical tracks to shaft box with angles and screws.
6. Attach door upper part to the wall with fasteners.
7. Fix the shaft box and drive casing.
Fig. 1
Fig. 2
13
INSTALLATION
Fig. 3
Fig. 4
14
INSTALLATION
Fig. 5
Fig. 6
15
INSTALLATION
Fig. 7
Fig. 7А
16
INSTALLATION
Fig. 8
Fig. 8А Fig. 8B
17
INSTALLATION
Fig. 9
Fig. 10
Fig. 11
18
5.7. HOW TO INSERT DOOR CURTAIN INTO VERTICAL TRACKS
INSTALLATION
Fig. 1
Fig. 1A Fig. 1B
1. Moving the tracks along adjustment holes, adjust curtain tension so that the gap between the track and the guide is
5 mm.
2. Once adjustment of curtain tension is completed check whether the curtain is properly tensioned, fasten the vetical
tracks firmly through all mounting holes, and install tracks casing.
Fig. 1
Once curtain is inserted into the door guides adjust door limit positions (see Installation and Operation Manual for Control
Unit).
6. MAINTENANCE
1. Before door service and maintenance technician 4. Never use open fire or heat source that may cause fire
should: when performing maintenance.
barricade the door and its working area from any form 5. Never use solvents of any kind.
of traffic. 6. No personel should be in the immediate vicinity of the
turn OFF power supply. serviced door unless maintenance technician needs
2. Maintenance and troubleshooting should only be help.
performed by trained technicians. Service interval depends on operating conditions but it's
3. Read these instructions thoroughly before service and necessary to carry out standard maintenance procedures
maintenance of the door. every six months.
Table 1. Service and maintenance highlights
Service item Procedure Interval
Visually inspect:
every six months
General condition of door curtain (clean door curtain with water and soap)
(more often if
the door vertical tracks necessary)
if necessary, clean the structure with compressed air
20
Table 1. Service and maintenance highlights (continued)
MAINTENANCE
Service item Procedure Interval
inspect wiring conduit and cables in control unit
inspect wiring conduit and cables inside junction box
inspect safety sensors (photocells, sensing edge and emergency stop button) every six months
Electrical
verify the opening/closing system functions properly (buttons and other optional (more often if
components
devices, if present) necessary)
verify that electric cables are in good working condition
clean photocells at least once a month or more often if necesssary
inspect motor
inspect motor brakes and perform their adjustment if necessary
inspect reducer chain for wear and tension (front drive)
inspect reducer for oil leakage; inspect mounting of the reducer to motor and to the
unit for tightness
every six months
Mechanical inspect limit switch for: wear of toothed belt, wear and mounting tightness of pulley,
(more often if
components correct functioning of arms and microswitches
necessary)
check all screws and bolts for tightness
check the axial alignment of the counterweight belt coil (door with counterbalance)
inspect bearings, lubricate if necessary
check traks sealing for signs of wear
check curtain guides alignment (can be cleaned with compressed air)
inpsect door curtain for signs of wear
check curtain for damage
verify that door curtain rolls up properly every six months
Door curtain adjust door curtain tension; check door mounting assembly for signs of wear and (more often if
tear necessary)
regularly clean the door curtain with soft wet cloth and mild detergent approved for
acrylic fabric
21
APPENDICES
APPENDICES
22
Table 1. Parts list
APPENDICES
# Name Condition Part number Qty Note
Hex bolt: D = М10, L = 30 mm,
1 DHM0177 8 for bearing support
non-galvanized
fastening of shaft box
2 Round head bolt (М8 × 16) 14016 6
back cover
Shaft assembly: D = 90 mm (side
Н ≤ 3,800, W ≤ 3,000 HSD112/M
drive)
total length = 115 + W
3 4,500 < W ≤ 5,000, 1
Shaft assembly: D = 127 mm (side + 285
H ≤ 3,800 or W ≤ 5,000, HSD1114/M
drive)
H > 3,800
Screw: D = M8, L = 14 mm, hex
4 socket cylinder head, DHM0659 2 for encoder fastening
non-galvanized
Nut: D = M10, self-locking,
5 153-17 8 for bearing support
galvanized
fastening of shaft box
6 Flange nut (М8) 14015 6
back cover
R15 reducer,
with heating W ≤ 4,000,
part number
JM motor H ≤ 3,800
HSDC R15
(1.5 kW) with HSDC 18186
R30 reducer,
heating with heating W ≤ 4,000,
part number
7 H > 3,800, or W > 4,000 1
HSDC R30
JM motor with
W ≤ 4,000, H ≤ 3,800 HSDC 18180
R15 reducer
JM motor with W ≤ 4,000, H > 3,800 or
HSDC18181
R30 reducer W > 4,000
Shaft box 250, L = 3,250 mm W ≤ 3,000, H ≤ 3,800 HSD 1400/250
3,000 < W ≤ 3,500 and
Shaft box 250, L = 3,750 mm HSD 1401/250
H ≤ 3,800
3,500 < W ≤ 4,000 and
Shaft box 250, L = 4,250 mm HSD 1402/250
H ≤ 3,800
Shaft box 250, L = 4,250 mm W ≤ 3,000 and H > 3,800 HSD 1400/350
3,000 < W ≤ 3,500 and
Shaft box 350, L = 3,750 mm HSD 1401/350
8 H > 3,800 1 L = W + 250
3,500 < W ≤ 4,000 and
Shaft box 350, L = 4,250 mm HSD 1402/350
H > 3,800
4,000 < W < = 4,500
Shaft box 350, L = 5,250 mm and H > 3,800 or HSD 1403/350
4,500 < W ≤ 5,000
Shaft box 350, L = 6,250 mm 5,000 < W ≤ 6,000 HSD 1404/350
Shaft box 350, L = 7,250 mm 6,000 < W HSD 1404-1/350
23
Table 1. Parts list (continued)
APPENDICES
24
Fig. 1. Exploded view
Ä À
Ä
Å Ã(1:4) Ä-Ä(1:1)
2
1 Å À 9
Á(1:4)
57 59 55
51
È 43 22
26 57
12 13
21
10 45
Á 53
14 44 47 19
49
3 È 23
17 46 54
11 23 Å-Å(1:1)
24 25 10 Â(1:4)
4 55
22
16 43
 à 18 45 57 59 13
14 9
30 20
42 53
47
23 19
15 49
24 54
33 Ê(1:4)
30
4 44 6
53 47 51
43
È-È(1:1) 55 45
APPENDIX 2. SPEEDROLL HIGH-SPEED DOOR (SIDE DRIVE)
5
À-À(1:2,5) 33 50 50
59
10 Ê 42
24 22 16 22 14 24 18 58
10 20 54 57
14 33 45 49
32
19 12 43
36 54
9 26
13
54
10 15 27 58
14 29
24 16 10 24 34 35 38
14 35 50 37
36 57
34 29
21 37 41
38
39 47 49
41 55
18
APPENDICES
25
Table 1. Parts list
APPENDICES
APPENDICES
# Name Condition Part number Qty Note
Shaft box, back cover 250
W <= 3,000 and H <= 3,800 HSD 1500/250
L = 3,250 mm
Shaft box, back cover 250 3,000 < W <= 3,500 and
HSD 1501/250
L = 3,750 mm H <= 3,800
Shaft box, back cover 250 3,500 < W <= 4,000 and
HSD 1502/250
L = 4,250 mm H <= 3,800
Shaft box, back cover 350
W <= 3,000 and H > 3,800 HSD 1500/350
L = 3,250 mm
Shaft box, back cover 350 3,000 < W <= 3,500 and
HSD 1501/350
17 L = 3,750 mm H > 3800 1 L = W + 250
Shaft box, back cover 350 3,500 < W <= 4,000 and
HSD 1502/350
L = 4,250 mm H > 3,800
4,000 < W <= 4500
Shaft box, back cover 350
and H > 3,800; HSD 1503/350
L = 5,250 mm
4,500 < W <= 5,000
Shaft box, back cover 350
5,000 < W <= 6,000 HSD 1504/350
L = 6,250 mm
Shaft box, back cover 350
6,000 < W HSD 1505/350
L = 7,250 mm
18 Motor housing 360 × 580 mm HSD 1830-2 1 side drive
End plate 250 W <= 4,500 and H <= 3,800 HSD 1405
19 W <= 4,500 and H > 3,800 2 side drive
End plate 350 HSD 1406
or W > 4,500
Drive casing front cover
20 HSD 1836-2 1
360 × 580 mm
Drive casing back cover
HSD 1838-2L
360 × 580 mm, left
Drive casing back cover
HSD 1838-2R
360 × 580 mm, right
21 drive to the left 1 side drive
Left back cover 250 of Joytech
HSD 1837-2L
drive casing
Right back cover 250 of Joytech
HSD 1837-2R
drive casing
22 Bearing support assembly HSD 2100 2
Self-tapping screw for metal
23 DHM0504 16
4,2 × 16
Self-tapping screw for metal
24 14019 7 for front drive casing
6,3 × 25 mm, for door panels
for drive, without
25 Key 7 × 8 × 80 HSD 2120 1
counterbalance
26 Tofi encoder HSDC 18190 1
Door curtain
for receiver fixation
in door pocket and
27 Velcro closure with PVC base SHVX008 1
for locking of bottom
pocket sides
28 COSMOFEN CA 12 glue CA 12 0.007
Set of plugs for safety edge safety edge —
29 SET_BAND 1
assembly optional
Toothed edge HSD 1901K L = H + 200
30 2
Toothed edge with reinforcement HSD 19010 optional for freezers
DoorHan logo for high-speed door
31 RP 77N 2
280 × 45 mm
32
DoorHan sticker for high-speed
door
RP 77 1
27
Table 1. Parts list (continued)
APPENDICES
28 H > 4,300 3
Table 1. Parts list (continued)
APPENDICES
# Name Condition Part number Qty Note
cable from drive to
48 5-core cable HSD 5005 L = (H + 3,000)
control unit
Track casing L = 3,200 mm HSD 1300
Track casing L = 3,700 mm HSD 1301
Track casing L = 4,000 mm HSD 1375
49 H <= 3,005 2 L = H + 195; n = 2 pcs
Track casing L = 4,200 mm HSD 1302
Track casing L = 5,200 mm HSD 1303
Track casing L = 6,200 mm HSD 1304
50 Rubber o-ring МПО 283 8 for photocells
51 Perforated bracket HSD 2112 2
52 ATTENTION sticker МПРП 026 1
H <= 1,800 1
53 Plastic guide L = 4,000 mm 1,800 < H <= 3,800 HSD 1900K 2 L = H + 200
H > 3,800 3
Self-tapping screw for metal every for fastening of shaft
54 DHM0504
4,2 × 16 250 mm box to vertical track
Vertical track L = 3,200 mm H <= 3,000 HSD 1100
Vertical track L = 3,700 mm 3,000 < H <= 3,500 HSD 1101
55 Vertical track L = 4,000 mm 3,500 < H <= 4,000 HSD 1180 2
Vertical track L = 5,200 mm 4,000 < H <= 5,000 HSD 1103
Vertical track L = 6,200 mm 5,000 < H HSD 1104
56 Black cable tie 9,650 mm КСС 9-650 8
every
H <= 4,000
250 mm
57 Spring HSD 2122
every
H > 4,000
250 mm
58 E3FA-TP11-D photocells HSDC 18200 1
every
H <= 4,000
250 mm
59 Flat galvanized washer D = 6.0 mm DHM0309
every
H > 4,000
250 mm
29
APPENDICES
30
Fig 1. Exploded view
4
10 4
10 4
Á 14 4 À(1:2)
10 10
9 21 17
3
24
13 5 24
27
24 À
23 24
16
Á(1:2)
19 23 3 1 21 9 12 6 20 11 7
23 25 15 28
27
23
8 9
26
22 18
APPENDIX 3. DOOR UPPER PART (FRONT DRIVE, WITHOUT COUNTERBALANCE)
Table 1. Parts list
APPENDICES
№ Name Condition Part number Qty Note
Side bracket 250 W ≤ 4,000 and H ≤ 3,800 HSD250PMF
1 W ≤ 4,000 and H > 3,800 or 1
Side bracket 350 HSD350PMF
W > 4,000
Hex bolt: D = М10, L = 20 mm,
2 DHM0122 4 for bracket fastening
galvanized,
Hex bolt: D = М10, L = 30 mm,
3 DHM0177 8 for bearing support
non-galvanized
fastening of shaft box
4 Round head bolt (М8 × 16) 14016 6
back cover
Shaft assembly: D = 90 mm (front
Н ≤ 3,800 and W ≤ 3,000 HSD1124/M
drive)
total length = 130 + W
5 4,500 < W ≤ 5,000 and 1
Shaft assembly: D = 127 mm (front + 130
H ≤ 3,800 or W ≤ 5,000 and HSD1128/M
drive)
H > 3,800
6 Transmission shaft HSD 1833 1
Screw: D = M8, L = 14 mm, hex
7 socket cylinder head, DHM0659 2 for encoder fastening
non-galvanized
8 Set screw (М6 × 16) DHM 0901 2
Nut: D = M10, self-locking, 8 for bearing support,
9 153-17 12
galvanized 4 for bracket fastening
fastening of shaft box
10 Flange nut (М8) 14015 6
back cover
R15 reducer,
with heating W ≤ 4,000 and
part number
JM motor H ≤ 3,800
HSDC R15
(1.5 kW) with HSDC 18186
R30 reducer,
heating with heating W ≤ 4,000 and
11 part number 1
H > 3,800 or W > 4,000
HSDC R30
JM motor with R15 reducer W ≤ 4,000 and H ≤ 3,800 HSDC 18180
W ≤ 4,000 and H > 3,800 or
JM motor with R30 reducer HSDC18181
W > 4,000
12 Chain lock HSD 1835 1
Shaft box 250, L = 3,250 mm W ≤ 3,000 and H ≤ 3,800 HSD 1400/250
3,000 < W ≤ 3,500 and
Shaft box 250, L = 3,750 mm HSD 1401/250
H ≤ 3,800
3,500 < W ≤ 4,000 and
Shaft box 250, L = 4,250 mm HSD 1402/250
H ≤ 3,800
Shaft box 350, L = 3,250 mm W ≤ 3,000 and H > 3,800 HSD 1400/350
3,000 < W ≤ 3,500 and
Shaft box 350, L = 3,750 mm HSD 1401/350
13 H > 3,800 1 L = W + 250
3,500 < W ≤ 4,000 and
Shaft box 350, L = 4,250 mm HSD 1402/350
H > 3,800
4,000 < W ≤ 4,500
Shaft box 350, L = 5,250 mm and H > 3,800 or HSD 1403/350
4,500 < W ≤ 5,000
Shaft box 350, L = 6,250 mm 5,000 < W ≤ 6,000 HSD 1404/350
Shaft box 350, L = 7,250 mm 6,000 < W HSD 1404-1/350
31
Table 1. Parts list (continued)
APPENDICES
32
Fig. 1. Exploded view
2 1
3
Á 12
 Â
18 22 12
13 18
34
4
Ä-Ä(2:1)
31 21 Ã
31 Ã
È À
51
Ä
39 Å
42 51 Ä
39
42 45
42
À(1:2)
È 30 17 29 25
26 11
44 47
27 46
43 38
30 50
41
Â-Â(1:1) Ã-Ã(1:1)
24 64
67 66 68 64
36 60 52
38 52
30 67 59 54 66 68
43 66
44
APPENDIX 4. SPEEDROLL HIGH-SPEED DOOR (FRONT DRIVE)
45 54 62
46 62 56
30 47 53 56
58 58
48 63
30 50 55 63
9 Á(1:2)
6
Å(1:4) 29 17 20
60 10 11 32 16
53 55
62 33 28 17
56 64
59 5 30 19
59 15
58 35
63 63 16
52 63 33
14 23
34
66 54 17
68
APPENDICES
33
Table 1. Parts list
APPENDICES
34
Table 1. Parts list (continued)
APPENDICES
# Name Condition Part number Qty Note
20 Chain lock HSD 1835
Shaft box 250 L = 3,250 mm W <= 3,000 and H <= 3,800 HSD 1400/250
3,000 < W <= 3,500 and
Shaft box 250 L = 3,750 mm HSD 1401/250
H <= 3,800
3,500<W <= 4,000 and
Shaft box 250 L = 4,250 mm HSD 1402/250
H <= 3,800
Shaft box 350 L = 3,250 mm W <= 3,000 and H > 3,800 HSD 1400/350
3,000 < W <= 3,500 and 1 L = W + 250
Shaft box 350 L = 3,750 mm HSD 1401/350
21 H > 3,800
3,500 < W <= 4,000 and
Shaft box 350 L = 4,250 mm HSD 1402/350
H > 3,800
4,000 < W <= 4,500
Shaft box 350 L = 5,250 mm and H > 3,800 or HSD 1403/350
4,500 < W <= 5,000
Shaft box 350 L = 6,250 mm 5,000 < W <= 6,000 HSD 1404/350
Shaft box 350 L = 7,250 mm 6,000 < W HSD 1404-1/350
Shaft box, back cover 250
W <= 3,000 and H <= 3,800 HSD 1500/250
L = 3,250 mm
Shaft box, back cover 250 3,000 < W <= 3,500 and
HSD 1501/250
L = 3,750 mm H <= 3,800
Shaft box, back cover 250 3,500<W <= 4,000 and
HSD 1502/250
L = 4,250 mm H <= 3,800
Shaft box, back cover 350
W <= 3,000 and H > 3,800 HSD 1500/350
L = 3,250 mm
Shaft box, back cover 350 3,000 < W <= 3,500 and
HSD 1501/350
22 L = 3,750 mm H > 3,800 1 L = W + 250
Shaft box, back cover 350 3,500<W <= 4,000 and
HSD 1502/350
L = 4,250 mm H > 3,800
4,000 < W <= 4,500
Shaft box, back cover 350
and H > 3,800; HSD 1503/350
L = 5,250 mm
4,500 < W <= 5,000
Shaft box, back cover 350
5,000 < W <= 6,000 HSD 1504/350
L = 6,250 mm
Shaft box, back cover 350
6,000 < W HSD 1505/350
L = 7,250 mm
23 External lock ring 25 DHM0320 4 for transmission shaft
24 Front cover 250 for Joytech drive HSD 250TLCF-J 1 front drive
End plate 250 W <= 4,500 and H <= 3,800 HSD 1405 front drive
25 W <= 4,500 and H > 3,800 1
End plate 350 HSD 1406
or W > 4,500
End plate 250 for Joytech drive
W <= 4,000 and H <= 3,800 HSD 1837FR-J
(right)
End plate 250 for Joytech drive
W <= 4,000 and H <= 3,800 HSD 1837FL-J
(left)
26 1 front drive
End plate 350 for Joytech drive W <= 4,000 and H > 3,800
HSD 1838FR-J
(right) or W > 4,000
End plate 350 for Joytech drive W <= 4,000 and H > 3,800
HSD 1838FL-J
(left) or W > 4,000
35
Table 1. Parts list (continued)
APPENDICES
36
44 Black PVC-fabric, width — 730 mm SHVH004 730*(W-100)
cutting: W - 100 × 100
Table 1. Parts list (continued)
APPENDICES
# Name Condition Part number Qty Note
sand pocket
Black PVC-fabric, width — 730 mm SHVH004 730*(W-100)
(W - 100) × 230
45 safety edge, optional;
Black PVC-fabric, width — 730 mm SHVH004 730*(W-300) sand pocket
(W - 300) × 260
46 Black PVC-fabric, width — 730 mm SHVH004 730*(W-100)
47 Quarry sand RMC241 0,002*W
48 Transmitter of safety edge signal TR_BAND 1 safety edge, optional
49 Receiver of safety edge signal REC_BAND 1 safety edge, optional
50 Rubber safety edge BAND1 L = (W - 100) safety edge, optional
Awning fabric RAL9010 pure white TT9010
Awning fabric, RAL1003 signal
HSD 1908
yellow
Awning fabric, RAL6026 opal green HSD 1904
Awning fabric, RAL3002 carmine
HSD 1906
51 red 1 W - 20; Н + 820
Awning fabric, RAL2004 pure
HSD 1907
orange
Awning fabric, RAL9006 white
TT9006
aluminium
Awning fabric, RAL5002
TT5002
ultramarine blue
Vertical track, 2 pcs
every
H <= 4,000
250 mm
52 Bolt (М6 × 80) DHM0183
every
H > 4,000
250 mm
for perforated angles
53 Round head bolt (М8 × 16) 14016 6
fastening
every
H <= 4,000
M6 self-locking nut (with nylon 250 mm
54 DHM0230
insert) every
H <= 4,000
250 mm
for perforated angles
55 Flange nut (М8) 14015 6
fastening
1
56 Plastic guide holder L = 4,500 mm 2,050 < H <= 4,300 HSD 1750 2
H > 4,300 3
cable from drive to
57 5-core cable HSD 5005 L = (H + 3,000)
control unit
Track casing L = 3,200 mm H <= 3,005 HSD 1300
Track casing L = 3,700 mm 3,005 < H <= 3,505 HSD 1301
Track casing L = 4,000 mm 3,005 < H <= 3,805 HSD 1375
58 2 L = H + 195; n = 2 pcs
Track casing L = 4,200 mm 3,805 < H <= 4,005 HSD 1302
Track casing L = 5,200 mm 4,005 < H <= 5,005 HSD 1303
Track casing L = 6,200 mm 5,005 < H HSD 1304
59 Rubber o-ring МПО 283 for photocells
60 Perforated bracket HSD 2112
61 ATTENTION sticker МПРП 026
37
Table 1. Parts list (continued)
APPENDICES
38
Fig. 1. Exploded view
4
8
À
3 À(1:2)
11 14 15
4
7
8
5
10 18
17
7
Á(1:2)
APPENDIX 5. DOOR UPPER PART (GFA DRIVE)
9 12 13
Á 15
7 2
14 2
3
2
1
7
6
16
APPENDICES
39
Table 1. Parts list
APPENDICES
40
Table 1. Parts list (continued)
APPENDICES
# Name Condition Part number Qty Note
Shaft box, back cover 250,
W ≤ 3,000 and H ≤ 3,800 HSD 1500/250
L = 3,250 mm
Shaft box, back cover 250, 3,000 < W ≤ 3,500 and
HSD 1501/250
L = 3,750 mm H ≤ 3,800
Shaft box, back cover 250, 3,500 < W ≤ 4,000 and
HSD 1502/250
L = 4,250 mm H ≤ 3,800
Shaft box, back cover 350,
W ≤ 3,000 and H > 3,800 HSD 1500/350
L = 3,250 mm
Shaft box, back cover 350, 3,000 < W ≤ 3,500 and
HSD 1501/350
11 L = 3,750 mm H > 3,800 1 L = W + 250
Shaft box, back cover 350, 3,500 < W ≤ 4,000 and
HSD 1502/350
L = 4,250 mm H > 3,800
4,000 < W ≤ 4,500
Shaft box, back cover 350,
and H > 3,800; HSD 1503/350
L = 5,250 mm
4,500 < W ≤ 5,000
Shaft box, back cover 350,
5,000 < W ≤ 6,000 HSD 1504/350
L = 6,250 mm
Shaft box, back cover 350,
6,000 < W HSD 1505/350
L = 7,250 mm
12 Drive bracket HSD 1802
Drive bracket SI 5.250 W·H ≤ 9,000,000 HSD 9102
13 1
Drive bracket SI 8.300 W·H > 9,000,000 HSD11101
End plate 250 (for shaft with
W ≤ 4,000 and H ≤ 3,800 HSD 9101
D = 30 mm)
14 2
End plate 350 (for shaft with W ≤ 4,000 and H > 3,800 or
HSD 9103
D = 30 mm) W > 4,000
15 UCF 206 bearing support assembly HSD9100 2
ELEKTROMAT drive «Safedrive»
SI5.250-30
SI5.250-30
16 W·H > 9,000,000 1
ELEKTROMAT drive «Safedrive»
SI8.300-30
SI8.300-30
Self-tapping screw for metal
17 14019 7 for front box
6,3 × 25 mm for door panels
18 Key 7 × 8 × 80 HSD 2120 HSD 2120 1
41
APPENDICES
42
Fig. 1. Exploded view
 5 Å(1:4) 11
56 15
 43 53 À(1:4) À
52 48
4 47 10 18
11
58 21 22 15
42 14 17
62 24 Á
à 60
46 51
à 12
29 25
62 57 57
32 41
Ä 60
32 29
Â-Â(1:1) Ã-Ã(1:1) 32
58
60 62 58
53
Ä 42 42
46 60 62
60 Å
2 1 46 56
56 48
43 48
51 51
57
47 57 44
45
61 31
APPENDIX 6. SPEEDROLL HIGH-SPEED DOOR (GFA DRIVE)
3 14 Á(1:4)
10 16 19 20
Ä-Ä(1:1) 44
22 26 45
14 9 28 61
33
14 41 34
21 9 35
36
13 9 8 37
23 38
35 40
34 37
36
33 28
40
Table 1. Parts list
APPENDICES
# Name Condition Part number Qty Note
1 Door upper part 1
2 Left track assembly 1
3 Right track assembly 1
for tracks fastening to
4 Round head bolt (М8 × 16) 14016 6
door upper part
for tracks fastening to
5 Flange nut (М8) 14015 6
door upper part
Installation and operation manual
6 IN055 1
for high-speed door
7 Technical data for high-speed door PSP25 1
Door upper part
Hex bolt: D = М8, L = 16 mm, for drive bracket
8 DHM0112 4
galvanized fastening
Hex bolt: D = М10, L = 20 mm, for drive fastening to
9 DHM0122 4
non-galvanized bracket and side cap
Hex bolt: D = М10, L = 30 mm,
10 DHM0177 8 for bearing support
non-galvanized
fastening of shaft box
11 Round head bolt (М8 х 16) 14016 6
back cover
Shaft assembly D = 90 mm (GFA
W <= 4,000 H <= 3,800 HSD 911/M 1 130 + W + 295
drive)
12 4,000 < W <= 5,000 and
Shaft assembly D = 127 mm (GFA
H <= 3,800 or W <= 5,000 HSD 915/M 1 130 + W+ 296
drive)
and H > 3,800
Set screw: D = 4,0 mm, L = 10 mm,
for encoder axis
13 with a hex socket head and cone 163-825 1
locking
point, galvanized
4 pcs for drive
Nut: D = M10, self-locking, fastening to bracket
14 153-17 12
galvanized and side cap; 8 pcs for
bearing support
fastening of shaft box
15 Flange nut (М8) 14015 6
back cover
for drive bracket
16 Flange nut (М8) 14016 4
fastening
Shaft box 250 L = 3,250 mm W <= 3,000 and H <= 3,800 HSD 1400/250
3,000 < W <= 3,500 and
Shaft box 250 L = 3,750 mm HSD 1401/250
H <= 3,800
3,500<W <= 4,000 and
Shaft box 250 L = 4,250 mm HSD 1402/250
H <= 3,800
Shaft box 350 L = 3,250 mm W <= 3,000 and H > 3,800 HSD 1400/350
3,000 < W <= 3,500 and
Shaft box 350 L = 3,750 mm HSD 1401/350
17 H > 3,800 1 L = W + 250
3,500 < W <= 4,000 and
Shaft box 350 L = 4,250 mm HSD 1402/350
H > 3,800
4,000 < W <= 4,500
Shaft box 350 L = 5,250 mm and H > 3,800 or HSD 1403/350
4,500 < W <= 5,000
Shaft box 350 L = 6,250 mm 5,000 < W <= 6,000 HSD 1404/350
Shaft box 350 L = 7,250 mm 6,000 < W HSD 1404-1/350
43
Table 1. Parts list (continued)
APPENDICES
44
Table 1. Parts list (continued)
APPENDICES
# Name Condition Part number Qty Note
PVC reinforcement (band), double,
HSD 1902/9010N
RAL9010 pure white
W <= 2,100 2
PVC reinforcement (band),
HSD 1902/ 1003
RAL1003 signal yellow
PVC reinforcement (band),
HSD 1902/6026
RAL6026 opal green
2,100 < W <= 4,250 3
PVC reinforcement (band),
HSD 1902/3002 L = H + 700
RAL3002 carmine red
32 PVC reinforcement (band),
HSD 1902/2004
RAL2004 pure orange
PVC reinforcement (band)
4,250 < W < 6,000 HSD 1902/9006 4
RAL9006 white aluminium
PVC reinforcement (band),
HSD 1902/5002
RAL5002 ultramarine blue
PVC reinforcement (band), double, 2,100 < W <= 4,250 1
HSD 1902N optional for freezers
transparent 4,250 < W < 6,000 2
curtain bottom part,
33 Black PVC-fabric, width — 730 mm SHVH004 730*(W-20)
cutting: (W - 20) × 400
ELEKTROMAT drive "Safedrive" sand pocket holder
34 SHVH004 730*(W-100)
SI8.300-30 (W - 100) × 100
sand pocket
Black PVC-fabric, width — 730 mm SHVH004 730*(W-100)
(W - 100) × 230
35 safety edge, optional;
Black PVC-fabric, width — 730 mm SHVH004 730*(W-300) sand pocket
(W - 300) × 260
safety edge, optional,
36 Black PVC-fabric, width — 730 mm SHVH004 730*(W-100) safety edge pocket
(W - 100) × 150
37 Quarry sand RMC241 0.002*W
38 Transmitter of safety edge signal TR_BAND 1 safety edge, optional
39 Receiver of safety edge signal REC_BAND 1 safety edge, optional
40 Rubber safety edge BAND1 L = (W - 100) safety edge, optional
Awning fabric RAL9010 pure white TT9010
Awning fabric, RAL1003 signal
HSD 1908
yellow
Awning fabric, RAL6026 opal green HSD 1904
Awning fabric, RAL3002 carmine
HSD 1906
41 red 1 W - 20; Н + 820
Awning fabric, RAL2004 pure
HSD 1907
orange
Awning fabric, RAL9006 white
TT9006
aluminium
Awning fabric, RAL5002
TT5002
ultramarine blue
Vertical track, 2 pcs
every
H <= 4,000 mm
250 mm
42 Bolt (М6 × 80) DHM0183
every
H > 4,000 mm
250 mm
for perforated angles
43 Round head bolt (М8 × 16) 14016 6
fastening
for photocell fastening
44 Screw (М4 × 10) SH 86 4
to vertical track
45
Table 1. Parts list (continued)
APPENDICES
46
NOTES
47
We thank you for purchasing the DoorHan prod-
uct. We hope that you will be satisfied with its
quality.