Professional Documents
Culture Documents
YZ250FH
2017 OWNER’S SERVICE MANUAL
YZ250FH
PRINTED ON RECYCLED PAPER PRINTED IN JAPAN LIT-11626-30-23 1SM-28199-13
2016.04––1.2 × 1 !
(E)
Genuine Yamaha Parts – Genuine Yamaha replacement parts are the exact same parts as the ones
originally equipped on your vehicle, providing you with the performance and durability you have come to
expect. Why settle for aftermarket parts that may not provide full confidence and satisfaction?
Genuine Yamaha Accessories – Yamaha only offers accessories that meet our high standards for quality
and performance. Buy with confidence, knowing your Genuine Yamaha Accessories will fit right and
perform right – right out of the box.
Yamalube – Take care of your Yamaha with legendary Yamalube oils, lubricants, and care products.
They're formulated and approved by the toughest judges we know: the Yamaha engineering teams that
know your Yamaha from the inside out.
Genuine Yamaha Service Manuals – Get the same factory manual for your vehicle that the technicians
at your authorized Yamaha dealer use. Service manuals are available through your Yamaha dealer or you
can order them directly through yamahapubs.com.
Genuine Yamaha products are available only from your Yamaha dealer.
Q Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
YZ250FH
OWNER’S SERVICE MANUAL
©2016 by Yamaha Motor Corporation, U.S.A.
1st Edition, April 2016
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in Japan
P/N. LIT-11626-30-23
INTRODUCTION
EAS1SME003
Congratulations on your purchase of a Yamaha YZ series. This model is the culmination of Yamaha’s
vast experience in the production of pacesetting racing machines. It represents the highest grade of
craftsmanship and reliability that have made Yamaha a leader.
This manual explains operation, inspection, basic maintenance and tuning of your machine. If you
have any questions about this manual or your machine, please contact your Yamaha dealer.
TIP
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual
contains the most current product information available at the time of printing, there may be minor
discrepancies between your machine and this manual. If you have any questions concerning this
manual, please consult your Yamaha dealer.
EWA
WARNING
PLEASE READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS
MACHINE. DO NOT ATTEMPT TO OPERATE THIS MACHINE UNTIL YOU HAVE ATTAINED A
SATISFACTORY KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES AND UNTIL
YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPEC-
TIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE
THAT YOU SAFETY ENJOY THE CAPABILITIES AND THE RELIABILITY OF THIS MACHINE.
In this manual, descriptions of installation, removal, disassembly, assembly, check, and adjustment
procedures are laid out with the individual steps in sequential order.
• The manual is divided into chapters and each chapter is divided into sections. The current section
title “1” is shown at the top of each page.
• Sub-section titles “2” appear in smaller print than the section title.
• To help identify parts and clarify procedure steps, there are exploded diagrams “3” at the start of
each removal and disassembly section.
• Numbers “4” are given in the order of the jobs in the exploded diagram. A number indicates a re-
moval or a disassembly step.
• Symbols “5” indicate parts to be lubricated or replaced.
Refer to “SYMBOLS”.
• A job instruction chart “6” accompanies the exploded diagram, providing the order of jobs, the
names of parts, the notes in jobs, etc.
• Jobs “7” requiring more information (such as special tools and technical data) are described se-
quentially.
5 1
4
2
7
SYMBOLS
EAS1SME008
The following symbols are used in this manual for easier understanding.
TIP
The following symbols are not relevant to every vehicle.
DESCRIPTION..................................................................................................1-2 1
IDENTIFICATION..............................................................................................1-3
VEHICLE IDENTIFICATION NUMBER ......................................................1-3
ENGINE SERIAL NUMBER........................................................................1-3
INCLUDED PARTS...........................................................................................1-4
SIDESTAND ...............................................................................................1-4
SPARK PLUG WRENCH............................................................................1-4
NIPPLE WRENCH......................................................................................1-4
HANDLEBAR PROTECTOR ......................................................................1-4
FUEL HOSE JOINT COVER ......................................................................1-4
COUPLER FOR CONNECTING OPTIONAL PART...................................1-4
IMPORTANT INFORMATION...........................................................................1-6
PREPARATION FOR REMOVAL AND DISASSEMBLY............................1-6
REPLACEMENT PARTS............................................................................1-6
GASKETS, OIL SEALS AND O-RINGS .....................................................1-7
LOCK WASHERS/PLATES AND COTTER PINS ......................................1-7
BEARINGS AND OIL SEALS .....................................................................1-7
CIRCLIPS ...................................................................................................1-7
CONTROL FUNCTIONS.................................................................................1-16
ENGINE STOP SWITCH ..........................................................................1-16
CLUTCH LEVER ......................................................................................1-16
SHIFT PEDAL...........................................................................................1-16
KICKSTARTER LEVER............................................................................1-16
THROTTLE GRIP .....................................................................................1-16
FRONT BRAKE LEVER ...........................................................................1-16
REAR BRAKE PEDAL..............................................................................1-17
STARTER KNOB/IDLE SCREW ..............................................................1-17
FUEL TANK CAP......................................................................................1-17
STARTING AND BREAK-IN...........................................................................1-18
FUEL.........................................................................................................1-18
STARTING A COLD ENGINE ..................................................................1-18
STARTING A WARM ENGINE .................................................................1-19
BREAK-IN PROCEDURES ......................................................................1-19
TORQUE-CHECK POINTS.............................................................................1-21
Please read the following important labels carefully before operating this vehicle.
1 2 3,4
1-1
DESCRIPTION
DESCRIPTION
EAS1SME010
1 2
6 5 4 3
7 8 9 12
11 10 17 16 15 14 13
1. Clutch lever 10. Coolant drain bolt
2. Front brake lever 11. Rear brake pedal
3. Throttle grip 12. Air filter
4. Radiator cap 13. Drive chain
5. Fuel tank cap 14. Shift pedal
6. Engine stop switch 15. Oil level check window
7. Fuel tank 16. Starter knob/idle screw
8. Kickstarter lever 17. Front fork
9. Radiator
TIP
Designs and specifications of the vehicle are subject to change without notice. Therefore, please
note that the descriptions in this manual may be different from those for the vehicle you have pur-
chased.
1-2
IDENTIFICATION
IDENTIFICATION
EAS1SME011
1-3
INCLUDED PARTS
WARNING a
• Never apply additional force to the sides-
tand.
• Remove this sidestand before starting out.
1
A
1
SPARK PLUG WRENCH
EAS1SME016
PART
1 The coupler “1” is used for connecting the op-
tional Power Tuner and so on.
ECA
NIPPLE WRENCH
EAS1SME017
NOTICE
The nipple wrench “1” is used to tighten the When no optional parts, etc. are connected,
spoke. connect the connection terminal to the orig-
inal coupler.
Before disconnecting the coupler, thor-
oughly wipe off any mud or water stuck to it.
1-4
INCLUDED PARTS
1-5
IMPORTANT INFORMATION
IMPORTANT INFORMATION
EAS20180
ASSEMBLY
1. Before the jobs, completely remove mud,
dust, and the like in order to prevent the en-
try of them into the inside during the jobs.
WARNING
Drain hole on the cylinder head (right side)
Coolant is potentially harmful and should
Hole under the water pump housing
be handled with special care.
• If it enters your eyes, wash it away with wa-
ter enough and then get medical attention
• If it splashes on your skin or clothes,
quickly wash it away with water and then
with soapy water.
• If it is swallowed, immediately induce vom-
iting and get medical attention.
REPLACEMENT PARTS
EAS1SME022
1-6
IMPORTANT INFORMATION
1. Oil
2. Lip
3. Spring
CIRCLIPS
EAS1SME026
4. Grease
When assembling parts, always use new cir-
LOCK WASHERS/PLATES AND COTTER
EAS1SME024
NOTICE
Do not spin the bearing with compressed air
because this will damage the bearing sur-
faces.
1-7
BASIC SERVICE INFORMATION
a
ELECTRICAL SYSTEM
EAS1SME028
NOTICE
Handle electrical components with special
care, and do not subject them to strong
shocks.
ECA16640
NOTICE
For waterproof couplers, never insert the
tester probes directly into the coupler.
When performing any checks using a water-
proof coupler, use the specified test har-
ness or a suitable commercially available
test harness.
ECA16630
NOTICE
Electrical components are very sensitive to
and can be damaged by static electricity.
Therefore, never touch the terminals and be
sure to keep the contacts clean.
NOTICE
Checking the electrical system
ECA14371
• When disconnecting a coupler, release the
NOTICE coupler lock, hold both sections of the
Never insert the tester probes into the cou- coupler, and then disconnect the coupler.
pler terminal slots. Always insert the probes • There are many types of coupler locks;
from the opposite end “a” of the coupler, therefore, be sure to check the type of cou-
taking care not to loosen or damage the pler lock before disconnecting the cou-
leads. pler.
1-8
BASIC SERVICE INFORMATION
1
ECA16790
NOTICE
When disconnecting a connector, do not
pull the leads. Hold both sections of the
connector, and then disconnect the con-
nector.
4. Connect:
• Lead
• Coupler
• Connector
TIP
• When connecting a coupler or a connector,
2. Check:
make sure that both terminals are connected
• Lead
securely.
• Coupler
• Make sure all connections are tight.
• Connector
Moisture Dry with compressed air.
Rust/stains Connect and disconnect sev-
eral times.
3. Check:
• All connections
Loose connection Connect properly.
TIP
• If the pin “1” on the terminal is flattened, bend
it up.
• After disassembling or assembling a coupler,
pull on the leads to make sure that they are in-
stalled securely.
1-9
BASIC SERVICE INFORMATION
5. Check:
• No continuity
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
TIP
• If there is no continuity, clean the terminals.
• When checking the wire harness, perform
steps (1) to (4).
• As a quick remedy, use a contact revitalizer
available at most part stores.
1-10
SPECIAL TOOLS
SPECIAL TOOLS
EAS1SME029
The following special tools are required for accurate and complete adjustment and assembly. Using
the correct special tool will help prevent damage caused by the use of improper tools or improvised
techniques. The shape and tool number used for the special tool differ by country, so two types are
provided. Refer to the list provided to avoid errors when placing an order.
TIP
• For U.S.A. and Canada, use tool number starting with “YM-”, “YU-”, or “ACC-”.
• For others, use tool number starting with “90890-”.
1-11
SPECIAL TOOLS
1-12
SPECIAL TOOLS
YM-04019
1-13
SPECIAL TOOLS
YM-91044
1-14
SPECIAL TOOLS
1-15
CONTROL FUNCTIONS
chassis.
The engine stop switch “1” is located on the left To start the engine, pull out and push down the
handlebar. Continue pushing the engine stop kickstarter lever with your foot.
switch till the engine comes to a stop.
1
THROTTLE GRIP
EAS1SME035
CLUTCH LEVER
EAS1SME032
EAS1SME037
1-16
CONTROL FUNCTIONS
b
a
1
1-17
STARTING AND BREAK-IN
FUEL
EAS1SME041
NOTICE
kickstarter lever in a stroke.
Use only unleaded gasoline. The use of 5. Immediately release the kickstarter lever.
leaded gasoline will cause severe damage EWA
WARNING
Yamaha because it can cause damage to the
fuel system or vehicle performance problems. Since exhaust gas contains harmful ingre-
dients, do not start or warm it up at an ill-
STARTING A COLD ENGINE
EAS1SME042
1-18
STARTING AND BREAK-IN
When the engine is warm, give a kick with the lem is found, immediately stop the engine
throttle closed without using the starter knob/ and make a checkup.
idle screw.
TIP
If it fails to start, fully open the throttle grip and
give 10 to 20 slow kicks to clear the engine of
the rich air-fuel mixture retained in it.
BREAK-IN PROCEDURES
EAS1SME044
NOTICE
Before running, do maintenance on the air
filter element.
Refer to “CLEANING THE AIR FILTER ELE-
MENT” on page 3-12.
1. After warming up the engine, drive it for
about 20 minutes at a throttle opening of 1/2
or less.
2. Make a pit stop, and check mounted areas
for looseness, oil leaks, or other problems.
3. Then, drive it for about 40 minutes at a throt-
tle opening of 3/4 or less.
4. Make a pit stop again, and thoroughly check
mounted areas for looseness, oil leaks, or
other problems. Thorough checks and ad-
justments are required in particular for
stretch of cables, free play of the brake,
stretch of the drive chain, looseness of the
spoke, and so on.
ECA
1-19
MAINTENANCE AFTER BREAK-IN
NOTICE
rect.
After a break-in or before each race, always
• Engine oil change
check the points shown in “TORQUE-
Drain the oil, and check for dirt and foreign
CHECK POINTS” for tightening torques and
materials such as metal chips. (If any foreign
retighten them. (Refer to “TORQUE-CHECK
material is mixed, disassemble and check
POINTS” on page 1-21.)
the crankcase.)
Pour the specified amount of the recom- • Greasing and oiling
mended oil. Always grease or oil the specified points.
• AC magneto
Check for looseness in mounted areas of
the rotor and the stator.
Check that the connector is not being dis-
connected.
• Silencer
Check the main body and stay for cracks.
Check for leaks.
• Mounting bolts and nuts
Check for looseness in mounted areas of
parts, as well as engine mounting bolts and
engine brackets.
2. For the chassis
• Check welds and mounted areas of the
frame, the swingarm, the link, the bracket,
and so on, for looseness and cracks.
• Wheel (s)
Check the wheel for runout. Check the
spoke for looseness.
• Brake(s)
Check the brake disc mounting bolt for
looseness.
Check that the reservoir contains the speci-
fied amount of brake fluid. Check for leaks.
1-20
TORQUE-CHECK POINTS
TORQUE-CHECK POINTS
EAS1SME047
1-21
TORQUE-CHECK POINTS
1-22
CLEANING AND STORAGE
NOTICE
Do not use high-pressure washers or steam
cleaners. Otherwise, these may cause a fail-
ure because of the entry of water.
4. After hosing off the dirt, wash all surfaces
with a mild detergent and warm water. Use
a toothbrush to clean hard-to-reach places.
5. Rinse the detergent with clean water, and
dry the surfaces with a soft towel or a cloth.
6. Immediately after cleaning, remove any wa-
ter from the drive chain with a paper towel,
and lubricate it to prevent rust.
7. Clean the seat with a vinyl upholstery clean-
er to keep the cover pliable and glossy.
8. Automotive wax may be applied to all paint-
ed or chromed surfaces. Avoid using such
wax as contains abrasives, because it may
scratch surfaces.
9. After completing the above, start the engine
and allow it to warm up for several minutes.
STORAGE
EAS1SME050
1-23
CLEANING AND STORAGE
1-24
SPECIFICATIONS
GENERAL SPECIFICATIONS..........................................................................2-1
GENERAL SPECIFICATIONS
EAS1SME051
Model
Model 1SME (USA) (CAN)
1SMJ (EUR)
1SMK (JPN)
1SML (AUS) (NZL) (ZAF)
Dimensions
Overall length 2165 mm (85.2 in)
Overall width 825 mm (32.5 in)
Overall height 1280 mm (50.4 in)
Seat height 965 mm (38.0 in)
Wheelbase 1475 mm (58.1 in)
Ground clearance 325 mm (12.80 in)
Weight
Curb weight 105 kg (231 lb)
2-1
ENGINE SPECIFICATIONS
ENGINE SPECIFICATIONS
EAS1SME052
Engine
Engine type Liquid cooled 4-stroke, DOHC
Displacement 250 cm3
Cylinder arrangement Single cylinder
Bore stroke 77.0 53.6 mm (3.03 2.11 in)
Compression ratio 13.5:1
Starting system Kickstarter
Fuel
Recommended fuel Premium unleaded gasoline only
Fuel tank capacity 7.5 L (2.0 US gal, 1.7 Imp.gal)
Engine oil
Lubrication system Wet sump
Recommended brand YAMALUBE
Type SAE 10W-40, SAE 10W-50, SAE 15W-40,
SAE 20W-40 or SAE 20W-50
Recommended engine oil grade API service SG type or higher, JASO standard
MA
Engine oil quantity
Quantity (disassembled) 0.90 L (0.95 US qt, 0.79 Imp.qt)
With oil filter element replacement 0.73 L (0.77 US qt, 0.64 Imp.qt)
Without oil filter element replacement 0.71 L (0.75 US qt, 0.62 Imp.qt)
Oil filter
Oil filter type Paper
Oil pump
Oil pump type Trochoid
Inner-rotor-to-outer-rotor-tip clearance Less than 0.150 mm (0.0059 in)
Limit 0.23 mm (0.0091 in)
Outer-rotor-to-oil-pump-housing clearance 0.13–0.18 mm (0.0051–0.0071 in)
Limit 0.25 mm (0.0098 in)
Oil-pump-housing-to-inner-and-outer-rotor
clearance 0.06–0.11 mm (0.0024–0.0043 in)
Limit 0.18 mm (0.0071 in)
Cooling system
Radiator (including all routes) 1.00 L (1.06 US qt, 0.88 Imp.qt)
Radiator capacity 0.58 L (0.61 US qt, 0.51 Imp.qt)
Radiator cap valve opening pressure 107.9–137.3 kPa (1.08–1.37 kg/cm2,
15.6–19.9 psi)
Radiator core
Width 112.6 mm (4.43 in)
Height 235.0 mm (9.25 in)
Depth 28.0 mm (1.10 in)
Water pump
Water pump type Single suction centrifugal pump
Spark plug(s)
Manufacturer/model NGK/LMAR8G
Spark plug gap 0.7–0.8 mm (0.028–0.031 in)
2-2
ENGINE SPECIFICATIONS
Cylinder head
Combustion chamber volume 12.07–12.87 cm3 (0.74–0.79 cu.in)
Warpage limit 0.05 mm (0.0020 in)
Camshaft
Drive system Chain drive (left)
Camshaft cap inside diameter 22.000–22.021 mm (0.8661–0.8670 in)
Camshaft journal diameter 21.959–21.972 mm (0.8645–0.8650 in)
Camshaft-journal-to-camshaft-cap clearance 0.028–0.062 mm (0.0011–0.0024 in)
Camshaft lobe dimensions
Lobe height (Intake) 31.800–31.900 mm (1.2520–1.2559 in)
Limit 31.700 mm (1.2480 in)
Base circle diameter (Intake) 22.450–22.550 mm (0.8839–0.8878 in)
Limit 22.350 mm (0.8799 in)
Lobe height (Exhaust) 33.850–33.950 mm (1.3327–1.3366 in)
Limit 33.750 mm (1.3287 in)
Base circle diameter (Exhaust) 25.211–25.311 mm (0.9926–0.9965 in)
Limit 25.111 mm (0.9886 in)
Camshaft runout limit 0.030 mm (0.0012 in)
Timing chain
Tensioning system Automatic
Valve, valve seat, valve guide
Valve clearance (cold)
Intake 0.12–0.19 mm (0.0047–0.0075 in)
Exhaust 0.17–0.24 mm (0.0067–0.0094 in)
Valve dimensions
Valve head diameter (intake) 30.90–31.10 mm (1.2165–1.2244 in)
Valve head diameter (exhaust) 24.90–25.10 mm (0.9803–0.9882 in)
Valve face width (intake) 1.697 mm (0.0668 in)
Valve face width (exhaust) 1.909 mm (0.0752 in)
Valve seat contact width (intake) 0.90–1.10 mm (0.0354–0.0433 in)
Valve seat contact width (exhaust) 0.90–1.10 mm (0.0354–0.0433 in)
Valve margin thickness (intake) 1.20 mm (0.0472 in)
Valve margin thickness (exhaust) 0.85 mm (0.0335 in)
Valve stem diameter (intake) 4.975–4.990 mm (0.1959–0.1965 in)
Limit 4.945 mm (0.1947 in)
Valve stem diameter (exhaust) 4.460–4.475 mm (0.1756–0.1762 in)
Limit 4.430 mm (0.1744 in)
Valve guide inside diameter (intake) 5.000–5.012 mm (0.1969–0.1973 in)
Limit 5.050 mm (0.1988 in)
Valve guide inside diameter (exhaust) 4.500–4.512 mm (0.1772–0.1776 in)
Limit 4.550 mm (0.1791 in)
Valve-stem-to-valve-guide clearance (intake) 0.010–0.037 mm (0.0004–0.0015 in)
Limit 0.080 mm (0.0032 in)
Valve-stem-to-valve-guide clearance (exhaust) 0.025–0.052 mm (0.0010–0.0020 in)
Limit 0.100 mm (0.0039 in)
Valve stem runout 0.010 mm (0.0004 in)
2-3
ENGINE SPECIFICATIONS
Valve spring
Free length (intake) 39.03 mm (1.54 in)
Limit 37.07 mm (1.46 in)
Free length (exhaust) 35.59 mm (1.40 in)
Limit 33.81 mm (1.33 in)
Installed length (intake) 32.50 mm (1.28 in)
Installed length (exhaust) 29.60 mm (1.17 in)
Spring rate K1 (intake) 25.56 N/mm (2.61 kgf/mm, 145.95 lbf/in)
Spring rate K2 (intake) 37.83 N/mm (3.86 kgf/mm, 216.01 lbf/in)
Spring rate K1 (exhaust) 24.53 N/mm (2.50 kgf/mm, 140.07 lbf/in)
Spring rate K2 (exhaust) 31.99 N/mm (3.26 kgf/mm, 182.66 lbf/in)
Installed compression spring force (intake) 155.00–179.00 N (15.81–18.25 kgf,
34.84–40.24 lbf)
Installed compression spring force (exhaust) 137.00–157.00 N (13.97–16.01 kgf,
30.80–35.29 lbf)
Spring tilt (intake) 2.5 °/1.7 mm (2.5 °/0.07 in)
Spring tilt (exhaust) 2.5 °/1.7 mm (2.5 °/0.07 in)
Winding direction (intake) Clockwise
Winding direction (exhaust) Clockwise
Cylinder
Bore 77.000–77.010 mm (3.0315–3.0319 in)
Taper limit 0.050 mm (0.0020 in)
Out of round limit 0.050 mm (0.0020 in)
Piston
Piston-to-cylinder clearance 0.030–0.055 mm (0.0012–0.0022 in)
Limit 0.15 mm (0.006 in)
Diameter 76.955–76.970 mm (3.0297–3.0303 in)
Measuring point (from piston skirt bottom) 4.0 mm (0.16 in)
Offset 0.00 mm (0.0000 in)
Piston pin bore inside diameter 16.002–16.013 mm (0.6300–0.6304 in)
Limit 16.043 mm (0.6316 in)
Piston pin outside diameter 15.991–16.000 mm (0.6296–0.6299 in)
Limit 15.971 mm (0.6288 in)
Piston ring
Top ring
Ring type Barrel
Dimensions (B T) 0.90 2.70 mm (0.04 0.11 in)
End gap (installed) 0.15–0.25 mm (0.0059–0.0098 in)
Limit 0.50 mm (0.0197 in)
Ring side clearance 0.030–0.065 mm (0.0012–0.0026 in)
Limit 0.115 mm (0.0045 in)
Oil ring
Dimensions (B T) 1.50 2.25 mm (0.06 0.89 in)
End gap (installed) 0.10–0.35 mm (0.0039–0.0138 in)
Crankshaft
Crank assembly width 55.95–56.00 mm (2.203–2.205 in)
Runout limit 0.030 mm (0.0012 in)
Big end side clearance 0.110–0.690 mm (0.0043–0.0272 in)
2-4
ENGINE SPECIFICATIONS
Balancer
Balancer drive method Gear
Clutch
Clutch type Wet, multiple-disc
Clutch release method Inner push, cam push
Clutch lever free play 7.0–12.0 mm (0.28–0.47 in)
Friction plate 1 thickness 2.90–3.10 mm (0.114–0.122 in)
Wear limit 2.85 mm (0.112 in)
Plate quantity 8 pcs
Friction plate 2 thickness 2.92–3.08 mm (0.115–0.121 in)
Wear limit 2.85 mm (0.112 in)
Plate quantity 1 pc
Clutch plate thickness 1.10–1.30 mm (0.043–0.051 in)
Plate quantity 8 pcs
Warpage limit 0.10 mm (0.004 in)
Clutch spring free length 45.00 mm (1.77 in)
Limit 42.75 mm (1.68 in)
Spring quantity 5 pcs
Push rod bending limit 0.30 mm (0.012 in)
Transmission
Transmission type Constant mesh 5-speed
Primary reduction system Spur gear
Primary reduction ratio 3.353 (57/17)
Final drive Chain
Secondary reduction ratio 3.846 (50/13)
Operation Left foot operation
Gear ratio
1st 2.143 (30/14)
2nd 1.750 (28/16)
3rd 1.444 (26/18)
4th 1.222 (22/18)
5th 1.042 (25/24)
Main axle runout limit 0.08 mm (0.0032 in)
Drive axle runout limit 0.08 mm (0.0032 in)
Shifting mechanism
Shift mechanism type Shift drum and guide bar
Shift fork guide bar bending limit 0.050 mm (0.0020 in)
Shift fork thickness 4.85 mm (0.1909 in)
Decompression device
Device type Auto decomp
Air filter
Air filter element Wet element
Air filter oil grade Yamaha foam air filter oil or other
quality foam air filter oil
Fuel pump
Pump type Electrical
Fuel injector
Model/quantity 30NA-FZ31/1
Resistance 12
2-5
ENGINE SPECIFICATIONS
Throttle body
Type/quantity 30RA-A71S/1
ID mark 1SM5 10
Fuel line pressure at idling 300.0–390.0 kPa (3.00–3.90 kgf/cm2,
43.5–56.6 psi)
Throttle position sensor
Resistance 6.30 k
Output voltage (at idle) 0.48–0.52 V
Fuel injection sensor
Crankshaft position sensor resistance 228–342
Intake air pressure sensor output voltage 3.57–3.71 V at 101.3 kPa
Intake air temperature sensor resistance 290–390 at 80 °C (176 °F)
Coolant temperature sensor resistance 2.51–2.78 k at 20 °C (68 °F)
210–221 at 100 °C (212 °F)
Idling condition
Engine idling speed 1900–2100 r/min
Water temperature 70–80 °C (158–176 °F)
Oil temperature 55–65 °C (131–149 °F)
Throttle grip free play 3.0–5.0 mm (0.12–0.20 in)
2-6
CHASSIS SPECIFICATIONS
CHASSIS SPECIFICATIONS
EAS1SME053
Chassis
Frame type Semi double cradle
Caster angle 27.1 °
Trail 118 mm (4.6 in)
Front wheel
Wheel type Spoke wheel
Rim size 1.60 21
Rim material Aluminum
Wheel travel 310 mm (12.2 in)
Radial wheel runout limit 2.0 mm (0.08 in)
Lateral wheel runout limit 2.0 mm (0.08 in)
Wheel axle bending limit 0.50 mm (0.02 in)
Rear wheel
Wheel type Spoke wheel
Rim size 1.85 19
Rim material Aluminum
Wheel travel 315 mm (12.4 in)
Radial wheel runout limit 2.0 mm (0.08 in)
Lateral wheel runout limit 2.0 mm (0.08 in)
Wheel axle bending limit 0.50 mm (0.02 in)
Front tire
Type With tube
Size 80/100-21 51M
Manufacturer/model BRIDGESTONE/M403A (USA) (CAN) (AUS)
(NZL) (ZAF)
PIRELLI/MID SOFT 32 (EUR)
DUNLOP/MX52F (JPN)
Rear tire
Type With tube
Size 100/90-19 57M
Manufacturer/model BRIDGESTONE/M404 (USA) (CAN) (AUS)
(NZL) (ZAF)
PIRELLI/MID SOFT 32 (EUR)
DUNLOP/MX52 (JPN)
Tire air pressure (measured on cold tires)
Front 100 kPa (1.00 kgf/cm2, 15 psi)
Rear 100 kPa (1.00 kgf/cm2, 15 psi)
Front brake
Type Hydraulic single disc brake
Operation Right hand operation
2-7
CHASSIS SPECIFICATIONS
2-8
CHASSIS SPECIFICATIONS
2-9
ELECTRICAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
EAS1SME054
Voltage
System voltage 12 V
Ignition system
Ignition system TCI
Advancer type Digital
Ignition timing (B.T.D.C.) 10.0 ° at 2000 r/min
Engine control unit
Model/manufacturer 1SM9/YAMAHA (USA) (CAN)
1SMA/YAMAHA (EUR) (JPN) (AUS) (NZL)
(ZAF)
Ignition coil
Minimum ignition spark gap 6.0 mm (0.24 in)
Primary coil resistance 2.16–2.64
Secondary coil resistance 8.64–12.96 k
Spark plug cap
Resistance 7.50–12.50 k
AC magneto
Standard output 14.0 V, 95 W at 5000 r/min
Stator coil resistance 0.624–0.936
Rectifier/regulator
Regulator type Single-phase
Regulated voltage (DC) 14.1–14.9 V
Rectifier capacity (DC) 23.0 A
2-10
TIGHTENING TORQUES
TIGHTENING TORQUES
EAS20320
CATIONS
This chart specifies tightening torques for stan-
dard fasteners with a standard ISO thread
pitch. Tightening torque specifications for spe-
cial components or assemblies are provided for
each chapter of this manual. To avoid warpage,
tighten multi-fastener assemblies in a criss-
cross pattern and progressive stages until the
specified tightening torque is reached. Unless
otherwise specified, tightening torque specifi-
cations require clean, dry threads. Compo-
nents should be at room temperature.
General tightening
B torques
A (nut)
(bolt)
Nm m·kgf ft·lbf
10 mm 6 mm 6 0.6 4.3
12 mm 8 mm 15 1.5 11
14 mm 10 mm 30 3.0 22
17 mm 12 mm 55 5.5 40
19 mm 14 mm 85 8.5 61
22 mm 16 mm 130 13.0 94
2-11
TIGHTENING TORQUES
TIP
- marked portion shall be checked for torque tightening after break-in or before each race.
Thread
ITEM Q’ty TIGHTENING TORQUES Remarks
size
Camshaft cap bolt M6 8 10 Nm (1.0 m·kgf, 7.2 ft·lbf) E
2-12
TIGHTENING TORQUES
Thread
ITEM Q’ty TIGHTENING TORQUES Remarks
size
Throttle cable nut (pull) M10 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Throttle cable nut (return) M10 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Clutch cable adjuster and locknut M6 1 4.3 Nm (0.43 m·kgf, 3.1 ft·lbf)
Clutch cable locknut (engine side) M8 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Exhaust pipe nut M8 2 See TIP.
Exhaust pipe protector screw M6 4 10 Nm (1.0 m·kgf, 7.2 ft·lbf) LT
Use a
Drive sprocket nut M18 1 75 Nm ( 7.5 m·kgf, 54 ft·lbf) lock
washer.
Segment M8 1 30 Nm (3.0 m·kgf, 22 ft·lbf)
Shift guide bolt M6 2 10 Nm (1.0 m·kgf, 7.2 ft·lbf) LT
2-13
TIGHTENING TORQUES
Thread
ITEM Q’ty TIGHTENING TORQUES Remarks
size
Stopper lever bolt M6 1 10 Nm (1.0 m·kgf, 7.2 ft·lbf) LT
Intake air temperature sensor screw M5 1 1.5 Nm (0.15 m·kgf, 1.1 ft·lbf)
Rectifier/regulator bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
ECU bolt M5 2 3.8 Nm (0.38 m·kgf, 2.8 ft·lbf)
Ignition coil bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Throttle position sensor screw M5 2 3.4 Nm (0.34 m·kgf, 2.5 ft·lbf)
Intake air pressure sensor screw M6 1 5 Nm (0.5 m·kgf, 3.6 ft·lbf)
TIP
Exhaust pipe nut
First temporarily tighten all nuts to 13 Nm (1.3 m·kgf, 9.4 ft·lbf). Then retighten them to 20 Nm (2.0
m·kgf, 14 ft·lbf).
EAS1SME057
2-14
TIGHTENING TORQUES
Thread
ITEM Q’ty TIGHTENING TORQUES Remarks
size
Outer tube and upper bracket bolt M8 4 21 Nm (2.1 m·kgf, 15 ft·lbf)
Outer tube and lower bracket bolt M8 4 21 Nm (2.1 m·kgf, 15 ft·lbf)
Upper bracket and steering stem nut M24 1 145 Nm (14.5 m·kgf, 105 ft·lbf)
Upper handlebar holder bolt M8 4 28 Nm (2.8 m·kgf, 20 ft·lbf)
Lower handlebar holder nut M10 2 40 Nm (4.0 m·kgf, 29 ft·lbf)
Engine stop switch screw M3 1 0.5 Nm (0.05 m·kgf, 0.36 ft·lbf)
Lower ring nut M28 1 See TIP.
Outer tube and damper assembly M51 2 30 Nm (3.0 m·kgf, 22 ft·lbf)
Inner tube and adjuster M22 2 55 Nm (5.5 m·kgf, 40 ft·lbf) LT
2-15
TIGHTENING TORQUES
Thread
ITEM Q’ty TIGHTENING TORQUES Remarks
size
Rear brake disc bolt M6 6 14 Nm (1.4 m·kgf, 10 ft·lbf) LT
2-16
TIGHTENING TORQUES
Thread
ITEM Q’ty TIGHTENING TORQUES Remarks
size
Drive chain support nut M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Drive chain guide bolt M5 3 4.0 Nm (0.40 m·kgf, 2.9 ft·lbf)
Rear frame and left cover bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel tank bolt (front side) M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel tank bolt (rear side) M6 1 9 Nm (0.9 m·kgf, 6.5 ft·lbf)
Fuel tank bracket bolt (front side) M6 4 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel tank bracket bolt (rear side) M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel pump bolt M5 6 4.0 Nm (0.40 m·kgf, 2.9 ft·lbf)
Fuel inlet pipe screw M5 2 3.4 Nm (0.34 m·kgf, 2.5 ft·lbf)
Fuel tank cap cover bolt M6 2 4.0 Nm (0.40 m·kgf, 2.9 ft·lbf)
Seat set bracket and fuel tank screw M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Seat bolt M8 2 22 Nm (2.2 m·kgf, 16 ft·lbf)
Left side cover bolt M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Right side cover bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Frame and air scoop bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Fuel tank and air scoop bolt M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Radiator guard and air scoop bolt M6 4 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Front fender bolt M6 4 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Rear fender bolt (front side) M6 4 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Rear fender bolt (rear side) M6 2 16 Nm (1.6 m·kgf, 12 ft·lbf)
Mud flap screw — 2 1.3 Nm (0.13 m·kgf, 0.94 ft·lbf)
Number plate bolt M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
TIP
Lower ring nut
1. First, tighten the lower ring nut approximately 38 Nm (3.8 m·kgf, 27 ft·lbf) by using the steering nut
wrench, then loosen the lower ring nut one turn.
2. Retighten the lower ring nut 7 Nm (0.7 m·kgf, 5.1 ft·lbf).
2-17
LUBRICATION POINTS AND LUBRICANT TYPES
Bearing E
O-ring LS
Valve stems M
Crankshaft journal M
Kick shaft E
2-18
LUBRICATION POINTS AND LUBRICANT TYPES
Yamaha bond
No.1215
Cylinder head cover gasket
(Three bond
No.1215®)
Yamaha bond
No.1215
Crankcase mating surface
(Three bond
No.1215®)
Yamaha bond
No.1215
Stator assembly lead grommet
(Three bond
No.1215®)
CHASSIS
EAS1SME060
Rear shock absorber assembly collar outer surface and dust seal lip (upper M
side)
Rear shock absorber assembly bearing and dust seal lip (lower side) M
2-19
LUBRICATION POINTS AND LUBRICANT TYPES
Tube guide (throttle grip) inner surface and throttle cable end LS
2-20
LUBRICATION SYSTEM CHART AND DIAGRAMS
LUBRICATION DIAGRAMS
EAS1SME062
2-21
LUBRICATION SYSTEM CHART AND DIAGRAMS
1. Intake camshaft
2. Exhaust camshaft
3. Piston
4. Oil nozzle
5. Oil filter element
6. Oil pump
7. Oil strainer
8. Crankshaft
9. Drive axle
10. Main axle
2-22
LUBRICATION SYSTEM CHART AND DIAGRAMS
2-23
LUBRICATION SYSTEM CHART AND DIAGRAMS
1. Connecting rod
2. Crankshaft
3. Main axle
4. Oil strainer
5. Drive axle
2-24
LUBRICATION SYSTEM CHART AND DIAGRAMS
2-25
LUBRICATION SYSTEM CHART AND DIAGRAMS
1. Exhaust camshaft
2. Intake camshaft
3. Oil filter element
4. Oil pump
2-26
LUBRICATION SYSTEM CHART AND DIAGRAMS
2-27
LUBRICATION SYSTEM CHART AND DIAGRAMS
1. Camshaft
2. Oil pressure check bolt
3. Oil filter element
4. Oil pump
2-28
CABLE ROUTING DIAGRAM
2-29
CABLE ROUTING DIAGRAM
2-30
CABLE ROUTING DIAGRAM
2-31
CABLE ROUTING DIAGRAM
2-32
CABLE ROUTING DIAGRAM
2-33
CABLE ROUTING DIAGRAM
1. Throttle cable
2. Clutch cable
3. Engine stop switch lead
4. Cable guide
5. Head pipe
6. Front brake hose
7. Brake hose guide
8. Number plate
A. Number plate band
B. Pass the clutch cable to the rear of the number
plate band.
C. Clamp the engine stop switch lead to the handle-
bar by the plastic band. Do not cut the end of the
plastic band.
D. Pass the engine stop switch lead between the
head pipe and the cable guide.
E. Pass the front brake hose to the front of the num-
ber plate.
F. 40°±10°
G. Vertical direction
H. Pass the engine stop switch lead under the han-
dlebar.
I. Pass the clutch cable to the guide in the number
plate.
2-34
CABLE ROUTING DIAGRAM
2-35
CABLE ROUTING DIAGRAM
1. Main harness
2. Radiator
3. Throttle position sensor lead
4. Joint coupler
5. Intake air temperature sensor lead
6. Intake air pressure sensor lead
7. Frame
8. Fuel hose
9. High tension cord
10. Spark plug cap
11. Cylinder head cover
12. Sub-wire harness
13. Injector coupler
14. Injector lead
15. Throttle body
16. Air filter case
17. ECU
18. Sub-wire harness coupler
A. Fix the main harness by the clamp, and insert the
projection of the clamp into the hole in the sheet
metal of the radiator.
B. Insert the projection of the main harness into the
hole in the frame.
C. To the sub-wire harness
D. Pass the high tension cord above the fuel hose.
E. ±10°
F. Install the spark plug cap with this facing the right
of the vehicle.
G. Push the spark plug cap home, where there shall
be no gap between it and the cylinder head cover.
H. Pass the injector lead to the top of the vehicle be-
yond the fuel hose.
I. Insert the coupler of the sub-wire harness into the
rib of the air filter case.
J. Pass the sub-wire harness between the ECU and
the air filter case.
2-36
CABLE ROUTING DIAGRAM
2-37
CABLE ROUTING DIAGRAM
2-38
CABLE ROUTING DIAGRAM
2-39
PERIODIC CHECKS AND ADJUSTMENTS
ENGINE.............................................................................................................3-8
CHECKING THE COOLANT LEVEL ..........................................................3-8
CHECKING THE COOLING SYSTEM .......................................................3-8
CHANGING THE COOLANT......................................................................3-8
CHECKING THE RADIATOR CAP.............................................................3-9
CHECKING THE RADIATOR CAP VALVE OPENING PRESSURE..........3-9
CHECKING THE COOLANT CIRCULATORY SYSTEM FOR LEAKS ....3-10
3
ADJUSTING THE CLUTCH LEVER POSITION.......................................3-10
ADJUSTING THE CLUTCH LEVER FREE PLAY ....................................3-10
ADJUSTING THE THROTTLE GRIP FREE PLAY...................................3-11
LUBRICATING THE THROTTLE CABLE.................................................3-12
CLEANING THE AIR FILTER ELEMENT.................................................3-12
CHECKING THE THROTTLE BODY JOINT ............................................3-13
CHECKING THE BREATHER HOSES ....................................................3-13
CHECKING THE EXHAUST SYSTEM.....................................................3-13
CHECKING THE FUEL LINE ...................................................................3-14
CHECKING THE ENGINE OIL LEVEL.....................................................3-14
CHANGING THE ENGINE OIL.................................................................3-15
ADJUSTING THE ENGINE IDLING SPEED ............................................3-16
ADJUSTING THE VALVE CLEARANCE..................................................3-17
CHASSIS ........................................................................................................3-22
BLEEDING THE BRAKE SYSTEM ..........................................................3-22
CHECKING THE BRAKE HOSE ..............................................................3-23
ADJUSTING THE FRONT BRAKE...........................................................3-23
ADJUSTING THE REAR BRAKE .............................................................3-24
CHECKING THE FRONT BRAKE PADS .................................................3-24
CHECKING THE REAR BRAKE PADS....................................................3-26
CHECKING THE REAR BRAKE PAD INSULATOR ................................3-27
CHECKING THE BRAKE FLUID LEVEL..................................................3-27
ADJUSTING THE DRIVE CHAIN SLACK ................................................3-28
CHECKING THE FRONT FORK LEGS....................................................3-29
CHECKING THE FRONT FORK PROTECTOR GUIDE ..........................3-29
CLEANING THE FRONT FORK OIL SEAL AND DUST SEAL ................3-29
AIR BLEEDING FROM FRONT FORK.....................................................3-29
ADJUSTING THE FRONT FORK LEGS ..................................................3-30
CHECKING THE SWINGARM OPERATION ...........................................3-31
CHECKING THE REAR SUSPENSION ...................................................3-31
ADJUSTING THE REAR SHOCK ABSORBER ASSEMBLY ...................3-31
CHECKING THE TIRES ...........................................................................3-33
CHECKING AND TIGHTENING THE SPOKES .......................................3-33
CHECKING THE WHEELS ......................................................................3-34
CHECKING THE WHEEL BEARINGS .....................................................3-34
CHECKING AND ADJUSTING THE STEERING HEAD ..........................3-34
LUBRICATING THE LEVERS ..................................................................3-35
LUBRICATING THE PEDAL.....................................................................3-35
ELECTRICAL SYSTEM..................................................................................3-36
CHECKING THE SPARK PLUG...............................................................3-36
CHECKING THE IGNITION TIMING ........................................................3-36
MAINTENANCE INTERVALS
MAINTENANCE INTERVALS
EAS1SME064
MAINTENANCE INTERVALS
EAS1SME065
ECA@
NOTICE
• After a break-in or before each race, always check the points shown in “TORQUE-CHECK
POINTS” for tightening torques and retighten them. (“TORQUE-CHECK POINTS” on page 1-
21.)
• Periodic inspection is essential in making full use of the machine performance. The life of
parts varies significantly according to the environment in which the machine runs (e.g., rain,
dirt, etc.). Therefore, earlier inspection is required by reference to the list below.
Every Every Every
After race third fifth
As re-
ITEM break- (about (about (about Remarks
quired
in 2.5 7.5 12.5
hours) hours) hours)
VALVE
Check the valve The engine must be cold.
clearances
Inspect Check the valve seats and the
valve faces for wear.
Replace
VALVE SPRING
Inspect Check the free length and the
tilt.
Replace
VALVE LIFTER
Inspect Check for scratches and wear.
Replace
CAMSHAFT Inspect the camshaft surface.
Inspect Inspect the decompression
system.
Replace
CAMSHAFT
SPROCKET
Inspect Check for wear on the teeth
and for damage.
Replace
PISTON
Inspect Inspect crack.
Clean Inspect carbon deposits and
eliminate them.
Replace Replace the piston, piston pin,
piston pin clip, and piston ring
all as a set.
3-1
MAINTENANCE INTERVALS
3-2
MAINTENANCE INTERVALS
3-3
MAINTENANCE INTERVALS
3-4
MAINTENANCE INTERVALS
3-5
MAINTENANCE INTERVALS
3-6
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation, practice or a race, make sure the machine is in good operating
condition.
Before using this machine, check the following points.
GENERAL INSPECTION AND MAINTENANCE
EAS1SME067
TIP
Perform usual maintenance enough so that, in the race course, a confirmation of that and simple set-
ting adjustments may only be left, in order to get enough time to use effectively.
3-7
ENGINE
1. Remove:
CHECKING THE COOLANT LEVEL
EAS1SME069
• Seat
• Side cover (left/right)
EWA1DX1003
WARNING
• Air scoop (left/right)
If coolant seems hot, do not remove the ra-
Refer to “GENERAL CHASSIS” on page 4-
diator cap.
1.
1. Stand the vehicle upright on a level surface. • Air filter case cover
2. Remove: Refer to “THROTTLE BODY” on page 7-5.
• Radiator cap “1” 2. Check:
• Radiator
• Radiator hoses
Crack/damage Replace.
Refer to “RADIATOR” on page 6-1.
3. Install:
• Air filter case cover
Refer to “THROTTLE BODY” on page 7-5.
• Air scoop (left/right)
• Seat
• Side cover (left/right)
3. Check: Refer to “GENERAL CHASSIS” on page 4-
• Coolant level 1.
Maximum level “a” or below Add coolant
CHANGING THE COOLANT
EAS1SME071
WARNING
If coolant seems hot, do not remove the ra-
diator cap.
1. Place a container under the engine.
2. Remove:
• Coolant drain bolt “1”
1. Radiator
1
ECA1DX1004
NOTICE
• Adding water instead of coolant lowers the
antifreeze content. If, therefore, water is
used instead of coolant, check, and if nec-
essary, adjust the antifreeze concentra-
tion. 3. Remove:
• Use only distilled water. However, if dis- • Radiator cap
tilled water is not available, soft water may Slowly loosen the radiator cap to drain cool-
be used. ant.
TIP
4. Start the engine, warm this up for several
minutes, and then stop it. When the radiator cap is loosened, coolant will
5. Check: gush out transversely; therefore, bring the con-
• Coolant level tainer near to the outlet.
TIP 4. Thoroughly flush the cooling system with
Before checking the coolant level, wait a few clean tap water.
minutes until the coolant has settled.
3-8
ENGINE
6. Pour coolant.
Recommended coolant
High quality ethylene glycol
anti-freeze containing anti-cor-
rosion for aluminum engine
Radiator (including all routes)
1.00 L (1.06 US qt, 0.88 Imp.qt)
Coolant mixing ratio CHECKING THE RADIATOR CAP VALVE
EAS1SME073
NOTICE
• Adding water instead of coolant lowers the
Radiator cap valve opening pres-
antifreeze content of the coolant. If water
sure
is used instead of coolant check, and if 107.9–137.3 kPa (1.08–1.37 kg/
necessary, correct the antifreeze concen- cm2, 15.6–19.9 psi)
tration of the coolant.
• Use only distilled water. However, if dis- No stay Replace.
tilled water is not available, soft water may
be used. Radiator cap tester
90890-01325
• If coolant comes into contact with painted
Mityvac cooling system tester kit
surfaces, immediately wash them with wa- YU-24460-A
ter. Radiator cap tester adapter
• Do not mix different types of antifreeze. 90890-01352
7. Install: Pressure tester adapter
• Radiator cap YU-33984
8. Start the engine, warm this up for several
minutes, stop it, and then wait for it to cool
down.
9. Check:
• Coolant level
Refer to “CHECKING THE COOLANT LEV-
EL” on page 3-8.
CHECKING THE RADIATOR CAP
EAS1SME072
1. Check:
• Seal (radiator cap) “1”
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3-9
ENGINE
2. Tighten:
• Locknut
Locknut
4.8 Nm (0.48 m·kgf, 3.5 ft·lbf)
T.
R.
PLAY
1. Check:
3. Activate the tester to apply the test pressure. • Clutch lever free play “a”
Out of specification Regulate.
Test pressure value
196 kPa (1.96 kg/cm2, 27.9 psi) Clutch lever free play
7.0–12.0 mm (0.28–0.47 in)
ECA@
NOTICE
• Do not apply such a high pressure as ex-
ceeds the test pressure.
• Make sure that a checkup after the cylin-
der head gasket is replaced is made after 2
to 3 minutes of warm-up.
• Make sure that coolant is filled up to the
upper level beforehand.
4. Check:
• Pressure value
No stay for 5 to 10 seconds at the test pres- 2. Adjust:
sure value Correct. • Clutch lever free play
• Radiator ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
• Radiator hose connections Handlebar side
Coolant leaks Correct or replace. a. Turn the adjuster “1” in direction “a” or “b”
• Radiator hoses until the specified clutch lever free play is ob-
Bulges Replace tained.
EWA@
3-10
ENGINE
b PLAY
1
TIP
Prior to adjusting throttle grip free play, the en-
a gine idling speed should be adjusted.
1. Check:
• Throttle grip free play “a”
Out of specification Regulate.
Throttle grip free play
TIP 3.0–5.0 mm (0.12–0.20 in)
If the clutch lever free play cannot be obtained
on the handlebar side, use the adjuster on the
clutch cable side.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
Clutch cable side
a. Slide the clutch cable cover.
b. Loosen the locknut “1”.
c. Turn the adjuster “2” in direction “a” or “b”
until the specified clutch lever free play is ob-
tained. 2. Adjust:
Direction “a” • Throttle grip free play
Clutch lever free play is increased. ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
Direction “b” a. Loosen the locknut “1”.
Clutch lever free play is decreased. b. Turn the adjuster “2” until the specified free
play is obtained.
d. Tighten the locknut “1”.
Direction “a”
Locknut Throttle grip free play is increased.
4.3 Nm (0.43 m·kgf, 3.1 ft·lbf) Direction “b”
T.
R.
WARNING
1 a After adjusting the throttle grip free play,
turn the handlebar to the right and to the left
to ensure that this does not cause the en-
gine idling speed to change.
b
2 2 1
b
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
a
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3-11
ENGINE
TIP
1. Remove: Loosen the quick fastener screw “3” and re-
• Cover (throttle cable cap) “1” move the air filter case cover.
• Cover (grip cap) “2”
• Throttle grip cap “3” 3
2 3
1
3
2. Remove:
2. Lubricate: • Air filter mounting bolt “1”
• Throttle cable end “a” • Air filter element “2”
• Air filter guide “3” (from the air filter element)
Recommended lubricant
Lithium-soap-based grease 3 1
3. Wash:
• Air filter element
EWA
3. Install: WARNING
• Throttle grip cap Do not use gasoline or organic (acid/alka-
• Screw (throttle grip cap) line) volatile oil for washing.
Screw (throttle grip cap) TIP
3.8 Nm (0.38 m·kgf, 2.8 ft·lbf) After washing the element with air filter cleaner
T.
R.
1. Remove:
• Fuel tank cap cover “1”
Refer to “FUEL TANK CAP” on page 1-17.
• Air filter case cover “2”
3-12
ENGINE
NOTICE
wet but not dripping.
Make sure the cylinder head breather hose
6. Install: is routed correctly.
• Air filter guide “1” (to the air filter element)
• Air filter element “2”
• Air filter mounting bolt “3”
Air filter mounting bolt
2.0 Nm (0.20 m·kgf, 1.4 ft·lbf) 1
T.
R.
1 3
1. Remove:
2 • Exhaust pipe protector
2. Check:
• Exhaust pipe 1
7. Install: • Exhaust pipe 2
• Air filter case cover “1” • Silencer
TIP Crack/damage Replace.
Refer to “ENGINE REMOVAL” on page 5-1.
Align the air filter case cover groove “a” with the
• Exhaust gas
air filter case edge “b”.
Leaks Replace the gasket.
Refer to “ENGINE REMOVAL” on page 5-1.
3. Check:
1 a • Tightening torques
Exhaust pipe bolt 1 and nut “1”
b 20 Nm (2.0 m·kgf, 14 ft·lbf)
T.
2 bolt “2”
12 Nm (1.2 m·kgf, 8.7 ft·lbf)
Exhaust pipe 2 and silencer bolt
“3”
8. Install: 12 Nm (1.2 m·kgf, 8.7 ft·lbf)
• Fuel tank cap cover Silencer and silencer bracket bolt
“4”
30 Nm (3.0 m·kgf, 22 ft·lbf)
3-13
ENGINE
3. Install:
• Fuel tank
Refer to “FUEL TANK” on page 7-1.
• Air scoop (left/right)
2 • Seat
• Side cover (left/right)
1 Refer to “GENERAL CHASSIS” on page 4-
1.
CHECKING THE ENGINE OIL LEVEL
EAS1SME084
LOCTITE®
R.
1. Remove: b
• Seat
• Side cover (left/right) a
• Air scoop (left/right) ECA33DD018
NOTICE
Refer to “GENERAL CHASSIS” on page 4-
1. • Since engine oil also lubricates the clutch,
• Fuel tank the wrong oil types or additives could
Refer to “FUEL TANK” on page 7-1. cause clutch slippage. Therefore, do not
2. Check: add any chemical additives.
• Fuel hose “1” • Do not allow foreign material to enter the
Crack/damage Replace. crankcase.
Loose connection Connect properly.
Recommended brand
YAMALUBE
Type
SAE10W-40, SAE10W-50,
1 SAE15W-40, SAE20W-40 or
SAE20W-50
Recommended engine oil grade
API service SG type or higher,
JASO standard MA
3-14
ENGINE
1
3 New 2
c. Install the new oil filter element and the oil fil-
CHANGING THE ENGINE OIL
EAS1SME085
T.
R.
about 5 minutes.
2. Place an oil pan under the drain bolt. ▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3. Remove: 5. To check the oil strainer, perform the follow-
• Oil filler cap “1” ing procedure.
• Drain bolt (with gasket) “2” ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the oil strainer “1”.
b. Check the oil strainer.
Damage Replace.
Clogging due to dirt Wash with kerosene.
c. Replace the O-rings “2”.
2 New 2
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
4. If the oil filter element is also to be replaced,
6. Install:
perform the following procedure.
• Gasket New
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ • Drain bolt
a. Remove the oil filter element cover “1” and
oil filter element “2”. Drain bolt
b. Replace the O-rings “3”. 20 Nm (2.0 m·kgf, 14 ft·lbf)
T.
R.
3-15
ENGINE
T.
R.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
TIP
8. Install: • Because the air pressure is lower at high alti-
• Oil filler cap tudes, the air-fuel mixture will become richer.
9. Check: If the idling speed is low, turn the starter knob/
• Oil level idle screw a few clicks counterclockwise to in-
Refer to “CHECKING THE ENGINE OIL crease the speed before the adjustment.
LEVEL” on page 3-14. • Before adjusting the engine idling speed,
10.Check: make sure that the air filter element is not
• Engine oil pressure clogged, the engine compression is proper,
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ and the throttle grip free play is proper.
a. Slightly loosen the oil pressure check bolt • Adjust the engine idling speed with the starter
“1”. knob/idle screw pushed in completely.
EWA
1 1
3-16
ENGINE
b 1
a
1 2
Direction “a” Engine idling speed De-
creases. 4. Check:
Direction “b” Engine idling speed In- • Valve clearance
creases. Out of specification Regulate.
Valve clearance (cold)
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
Intake
0.12–0.19 mm (0.0047–0.0075 in)
Exhaust
0.17–0.24 mm (0.0067–0.0094 in)
3-17
ENGINE
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ 1
a. Turn the crankshaft counterclockwise with a
wrench.
b. Align the top dead center (TDC) mark “a” on
the rotor with the alignment mark “b” on the
crankcase cover.
a ▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
5. Adjust:
• Valve clearance
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the camshaft (intake and exhaust).
Refer to “CAMSHAFT” on page 5-11.
TIP b. Remove the valve lifter “2” and the adjusting
pad “3” with a valve lapper “1”.
Check that the alignment mark “c” on the cam-
shaft sprocket and the alignment mark “d” on TIP
the intake camshaft sprocket are aligned with • Place a cloth in the timing chain space to pre-
the edge of the cylinder head. vent adjusting pads from falling into the crank-
case.
• Identity each valve lifter and adjusting pad po-
d c sition very carefully so that they can be rein-
stalled in their original place.
Valve lapper
90890-04101
Valve lapping tool
YM-A8998
1
c. Measure the valve clearance “e” using a 2
thickness gauge “1”. 3
TIP
Record the measured reading if the clearance
is incorrect.
e e
3-18
ENGINE
5
4
Example:
Pad number = 148
Rounded value = 150
e. Install the new adjusting pads “4” and the
valve lifters “5”.
ECA@
NOTICE
Do not twist adjusting pads and valve lifters
forcibly during installation.
3-19
ENGINE
INTAKE
120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.00 0.01 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225
0.02 0.06 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230
0.07 0.11 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235
0.12 0.19
0.20 0.24 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.25 0.29 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.30 0.34 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.35 0.39 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.40 0.44 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.45 0.49 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.50 0.54 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.55 0.59 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.60 0.64 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.65 0.69 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.70 0.74 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.75 0.79 180 185 190 195 200 205 210 215 220 225 230 235 240
0.80 0.84 185 190 195 200 205 210 215 220 225 230 235 240
0.85 0.89 190 195 200 205 210 215 220 225 230 235 240
0.90 0.94 195 200 205 210 215 220 225 230 235 240
0.95 0.99 200 205 210 215 220 225 230 235 240
1.00 1.04 205 210 215 220 225 230 235 240
1.05 1.09 210 215 220 225 230 235 240
1.10 1.14 215 220 225 230 235 240
1.15 1.19 220 225 230 235 240
1.20 1.24 225 230 235 240
1.25 1.29 230 235 240
1.30 1.34 235 240
1.35 1.39 240
A. Measured clearance
B. Installed pad number
C. Standard clearance
Example:
Valve clearance (cold) 0.12–0.19 mm
(0.0047–0.0075 in)
Installed is 175
Measured clearance 0.27 mm (0.0106 in)
Replace 175 pad with 185 pad
Pad No.175 = 1.75 mm (0.0689 in)
Pad No.185 = 1.85 mm (0.0728 in)
3-20
ENGINE
EXHAUST
120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.00 0.01 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220
0.02 0.06 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225
0.07 0.11 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230
0.12 0.16 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235
0.17 0.24
0.25 0.29 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.30 0.34 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.35 0.39 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.40 0.44 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.45 0.49 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.50 0.54 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.55 0.59 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.60 0.64 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.65 0.69 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.70 0.74 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.75 0.79 175 180 185 190 195 200 205 210 215 220 225 230 235 240
0.80 0.84 180 185 190 195 200 205 210 215 220 225 230 235 240
0.85 0.89 185 190 195 200 205 210 215 220 225 230 235 240
0.90 0.94 190 195 200 205 210 215 220 225 230 235 240
0.95 0.99 195 200 205 210 215 220 225 230 235 240
1.00 1.04 200 205 210 215 220 225 230 235 240
1.05 1.09 205 210 215 220 225 230 235 240
1.10 1.14 210 215 220 225 230 235 240
1.15 1.19 215 220 225 230 235 240
1.20 1.24 220 225 230 235 240
1.25 1.29 225 230 235 240
1.30 1.34 230 235 240
1.35 1.39 235 240
1.40 1.44 240
A. Measured clearance
B. Installed pad number
C. Standard clearance
Example:
Valve clearance (cold) 0.17–0.24 mm
(0.0067–0.0094 in)
Installed is 175
Measured clearance 0.32 mm (0.0126 in)
Replace 175 pad with 185 pad
Pad No.175 = 1.75 mm (0.0689 in)
Pad No.185 = 1.85 mm (0.0728 in)
3-21
CHASSIS
CHASSIS
EAS1SME088
B
2
BLEEDING THE BRAKE SYSTEM
EAS1SME089
EWA
WARNING
Bleed the brake system whenever: 1
• The system is disassembled.
• A brake hose is loosened, disconnected,
or replaced.
• The brake fluid level is very low.
• Brake operation is faulty.
A. Front
1. Remove: B. Rear
• Brake master cylinder cap d. Slowly apply the brake several times.
• Reservoir diaphragm e. Fully pull the brake lever or fully press down
• Reservoir float (front brake) the brake pedal and hold it in position.
• Protector (rear brake) f. Loosen the bleed screw.
TIP TIP
• Be careful not to spill any brake fluid or allow Loosening the bleed screw will release the
the reservoir to overflow. pressure in the brake caliper and cause the
• Make sure that there is enough brake fluid be- brake lever to contact the throttle grip or the
fore applying the brake. Ignoring this precau- brake pedal to fully extend.
tion could allow air to enter the brake system,
considerably lengthening the bleeding proce- g. Tighten the bleed screw and then release
dure. the brake lever or brake pedal.
• If bleeding is difficult, it may be necessary to h. Repeat steps (d) to (g) until all of the air bub-
let the brake fluid settle for a few hours. Re- bles have disappeared from the brake fluid
peat the bleeding procedure when the tiny in the plastic hose.
bubbles in the hose have disappeared. TIP
2. Bleed the brake system. During the procedure, keep adding brake fluid
to the reservoir.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Fill the reservoir to the proper level with the
ECA
NOTICE
recommended brake fluid.
• Wipe off any brake fluid on the brake
b. Install the reservoir diaphragm.
discs, tires, wheels, etc.
c. Connect the plastic hose “1” to the bleed
• Brake fluid may erode painted surfaces or
screw “2” securely, and place a container
plastic parts. Always clean up spilled fluid
under the end of the plastic hose.
immediately.
A
i. Tighten the bleed screw.
2
Bleed screw
1 6 Nm (0.6 m·kgf, 4.3 ft·lbf)
T.
R.
WARNING
After bleeding the hydraulic brake system,
check the brake operation.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3-22
CHASSIS
1. Check:
• Brake hose “1”
Cracks/damage/wear Replace.
2. Remove:
• Brake lever cover
3. Adjust:
• Brake lever position
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Loosen the locknut “1”.
b. Turn the adjusting bolt “2” in direction “a” or
“b” until the specified brake lever position is
obtained.
Direction “a”
1 Brake lever position is increased.
Direction “b”
Brake lever position is decreased.
A. Front
B. Rear
2. Check: a
• Brake hose clamp
Loose Connection Tighten the clamp bolt.
3. Stand the vehicle upright and apply the front b
brake and the rear brake several times.
4. Check:
• Brake hoses
Brake fluid leaks Replace the damaged
brake hose. c. Tighten the locknut.
Refer to “FRONT BRAKE” on page 4-11. Locknut
Refer to “REAR BRAKE” on page 4-21. 5 Nm (0.5 m·kgf, 3.6 ft·lbf)
T.
R.
EWA13050
1. Check: WARNING
• Brake lever position “a” A soft or spongy feeling in the brake lever
can indicate the presence of air in the brake
Brake lever position
95 mm (3.74 in) system. Before the vehicle is operated, the
Extent of adjustment air must be removed by bleeding the brake
86–105 mm (3.39–4.13 in) system. Air in the brake system will consid-
erably reduce braking performance.
ECA13490
NOTICE
After adjusting the brake lever position,
make sure there is no brake drag.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
4. Install:
• Brake lever cover
3-23
CHASSIS
NOTICE
1. Check: After adjusting the brake pedal position,
• Brake pedal position “a” make sure that there is no brake drag.
(distance from the top of the rider footrest to
the top of the brake pedal) ▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
Out of specification Regulate. CHECKING THE FRONT BRAKE PADS
EAS1SME093
EWA
WARNING
A soft or spongy feeling in the brake pedal
can indicate the presence of air in the brake
system. Before running, bleed the brake
system. Air in the brake system will cause
braking performance to be reduced.
ECA
3-24
CHASSIS
T.
Pad pin
R.
4
17 Nm (1.7 m·kgf, 12 ft·lbf)
3-25
CHASSIS
4
1. Measure:
• Brake pad thickness “a” 3
Out of specification Replace as a set.
TIP
The pads worn up to the indicator “b” grooves
mean that the brake pad thickness limit is
reached. 5
a
a
2. Replace:
• Brake pads
9
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the protector “1” and the pad pin 8
plug “2”.
WARNING
Do not reuse the drained brake fluid.
1 g. Tighten the bleed screw.
Bleed screw
b. Loosen the pad pin “3”. 6 Nm (0.6 m·kgf, 4.3 ft·lbf)
T.
R.
3-26
CHASSIS
4. Check:
11 10 • Brake pedal operation
A softy or spongy feeling Bleed the brake
system.
Refer to “BLEEDING THE BRAKE SYS-
TEM” on page 3-22.
a
CHECKING THE REAR BRAKE PAD INSU-
EAS1SME095
b
LATOR
1. Remove:
• Brake pads
i. Install the brake caliper “12” and the rear
Refer to “REAR BRAKE” on page 4-21.
wheel “13”.
2. Check:
Refer to “REAR WHEEL” on page 4-7.
• Rear brake pad insulator “1”
j. Tighten the pad pin “14”.
Damage Replace.
Pad pin
17 Nm (1.7 m·kgf, 12 ft·lbf)
T.
R.
13
14
12
CHECKING THE BRAKE FLUID LEVEL
EAS1SME096
Bolt (protector)
R.
2. Check:
7 Nm (0.7 m·kgf, 5.1 ft·lbf) • Brake fluid level
The minimum level mark “a” or below
Add.
15 Specified brake fluid
DOT 4
16
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3. Check:
• Brake fluid level
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-27.
A. Front brake
B. Rear brake
EWA
3-27
CHASSIS
WARNING
• Use only the designated brake fluid. Other
brake fluids may cause the rubber seals to a
deteriorate, causing leakage and poor
brake performance.
• Refill with the same type of brake fluid that
is already in the system. Mixing brake flu-
ids may result in a harmful chemical reac-
tion, leading to poor brake performance.
• When refilling, be careful that water does
not enter the brake fluid reservoir. Water Drive chain slack
will significantly lower the boiling point of 50.0–60.0 mm (1.97–2.36 in)
the brake fluid and could cause vapor
lock. 5. Adjust:
ECA
• Drive chain slack
NOTICE
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
Brake fluid may damage painted surfaces a. Loosen the wheel axle nut “1”.
and plastic parts. Therefore, always clean b. Loosen both locknuts “2”.
up any spilt brake fluid immediately. c. Turn the adjusting bolt “3” in direction “a” or
“b” until the specified drive chain slack is ob-
ADJUSTING THE DRIVE CHAIN SLACK
EAS1SME097
ECA13550
tained.
NOTICE Direction “a”
A drive chain that is too tight will overload The drive chain slack decreases.
the engine and other vital parts, and one Direction “b”
that is too loose can skip and damage the The drive chain slack increases.
swingarm or cause an accident. Therefore,
keep the drive chain slack within the speci-
fied limits.
1. Use a suitable stand to raise the rear wheel a
off the ground.
EWA13120
WARNING b
Securely support the vehicle so that there is 1
no danger of it falling over. 2
2. Shift the transmission into the neutral posi- 3
tion.
3. Pull the drive chain up above the drive chain TIP
guide installation bolt with a force of about • To maintain the proper wheel alignment, ad-
50 N (5.0 kgf, 36 lbf). just both sides evenly.
4. Check: • Push the rear wheel forward to make sure that
• Drive chain slack “a” there is no clearance between the swingarm
Out of specification Regulate. end plates and the ends of the swingarm.
TIP d. Tighten the wheel axle nut.
Measure drive chain slack between the drive
Wheel axle nut
chain guide and the bottom of the chain as 135 Nm (13.5 m·kgf, 98 ft·lbf)
shown.
T.
R.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3-28
CHASSIS
CHECKING THE FRONT FORK LEGS CLEANING THE FRONT FORK OIL SEAL
EAS1SME098 EAS1SME100
WARNING
• Protector
Securely support the vehicle so that there is
• Dust seal “1”
no danger of it falling over. ECA
NOTICE
2. Check:
• Inner tube Be careful not to damage the dust seal and
Damage/scratches Replace. the inner tube by a driver.
• Front fork leg (s)
Oil leaks between inner tube and outer tube
Replace the oil seal.
3. Hold the vehicle upright and apply the front
brake.
4. Check:
• Front fork operation
Push down hard on the handlebar several
times and check if the front fork rebounds 1
smoothly.
Unsmooth operation Correct or replace. 2. Clean:
Refer to “FRONT FORK” on page 4-37. • Dust seal “a”
• Oil seal “b”
TIP
• Clean the dust seal and oil seal after every
run.
• Apply lithium-soap-based grease on the inner
tube.
WARNING
Securely support the vehicle so that there is
no danger of it falling over.
a
2. Remove the air bleed screw “1” and release
the internal pressure from the front fork.
3-29
CHASSIS
3. Tighten:
• Air bleed screw
Air bleed screw
1.3 Nm (0.13 m·kgf, 0.94 ft·lbf)
T.
R.
1
a b
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
Compression damping
ECA@
NOTICE
Do not turn the adjuster forcibly beyond its
ADJUSTING THE FRONT FORK LEGS
EAS1SME102
adjusting range.
1. Adjust:
EWA32D1006
WARNING
• Compression damping
• Always adjust the left and right front forks
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
evenly. If this is not done, the vehicle may
a. Turn the adjuster “1” in the direction of “a” or
have poor stability.
“b” to make an adjustment.
• Securely support the vehicle so that there
is no danger of it falling over. Direction “a”
Compression damping is increased
Rebound damping (suspension is harder).
ECA@ Direction “b”
NOTICE Compression damping is decreased
Do not turn the adjuster forcibly beyond its (suspension is softer).
adjusting range.
1. Adjust: Compression damping adjusting
positions
• Rebound damping
Maximum
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ Fully turned in
a. Turn the adjuster “1” in the direction of “a” or Standard
“b” to make an adjustment. 11 clicks out*
Minimum
Direction “a”
20 clicks out*
Rebound damping is increased (sus-
pension is harder). * With the adjuster fully turned in
Direction “b”
Rebound damping is decreased (sus-
pension is softer). b a
3-30
CHASSIS
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
1. Stand the vehicle upright on a level surface. a. Loosen the locknut “1”.
EWA
b. Loosen the adjuster “2” until there is some
WARNING clearance between the spring and the ad-
Securely support the vehicle so that there is juster.
no danger of it falling over. c. Measure the spring free length “a”.
2. Check:
• Rear shock absorber assembly
Gas leaks/oil leaks Replace the rear
shock absorber assembly.
Refer to “REAR SHOCK ABSORBER AS-
SEMBLY” on page 4-53.
3. Check:
• Rear shock absorber assembly smooth ac-
tion
• Rear suspension link smooth action
Sit astride the seat and shake your body up d. Turn the adjuster in the direction of “b” or “c”
to make an adjustment.
and down several times to check whether
the rear shock absorber assembly operates Direction “b”
smoothly. Spring preload is increased (suspen-
Unsmooth operation Correct or replace. sion is harder).
Refer to “REAR SHOCK ABSORBER AS- Direction “c”
SEMBLY” on page 4-53. Spring preload is decreased (suspen-
sion is softer).
WARNING
turned in 18 mm (0.71 in) from its
Securely support the vehicle so that there is free length.
no danger of it falling over.
TIP
Spring preload • Be sure to remove all dirt and mud from
around the locknut and adjusting ring before
ECA@
NOTICE
adjustment.
Do not turn the adjuster forcibly beyond its • The length of the spring (installed) changes
adjusting range. 1.5 mm (0.06 in) per turn of the adjusting ring.
3-31
CHASSIS
c
b
a
b
1
e. Tighten the locknut. ▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
Locknut
Compression damping (for fast compres-
30 Nm (3.0 m·kgf, 22 ft·lbf)
sion damping)
T.
R.
ECA@
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲ NOTICE
3. Install: Do not turn the adjuster forcibly beyond its
• Rear frame adjusting range.
Refer to “REAR SHOCK ABSORBER AS-
1. Adjust:
SEMBLY” on page 4-53.
• Compression damping (for fast compression
Rebound damping damping)
ECA@
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
NOTICE a. Turn the adjuster “1” in the direction of “a” or
Do not turn the adjuster forcibly beyond its “b” to make an adjustment.
adjusting range.
Direction “a”
1. Adjust: Compression damping is increased
• Rebound damping (suspension is harder).
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ Direction “b”
a. Turn the adjuster “1” in the direction of “a” or Compression damping is decreased
“b” to make an adjustment. (suspension is softer).
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3-32
CHASSIS
NOTICE
Out of specification Regulate.
Do not turn the adjuster forcibly beyond its
adjusting range. Tire air pressure (measured on cold
1. Adjust: tires)
• Compression damping (for slow compres- Front
100 kPa (1.00 kgf/cm2, 15 psi)
sion damping)
Rear
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ 100 kPa (1.00 kgf/cm2, 15 psi)
a. Turn the adjuster “1” in the direction of “a” or
“b” to make an adjustment. TIP
Direction “a” • Check the tire while it is cold.
Compression damping is increased • Loose bead stoppers allow the tire to slip off
(suspension is harder). its position on the rim when the tire pressure
Direction “b” is low.
Compression damping is decreased • If the tire valve stem is found tilted, the tire is
(suspension is softer). considered to be slipping off its position. Cor-
rect the tire position.
Compression damping setting
(for slow compression damping)
Maximum
Fully turned in
Standard
11 clicks out* (USA) (CAN) (JPN)
(AUS) (NZL) (ZAF)
15 clicks out* (EUR)
Minimum
20 clicks out*
* With the adjuster fully turned in
CHECKING AND TIGHTENING THE
EAS1SME107
SPOKES
1. Check:
• Spokes
b Bend/damage Replace.
1 a Loose Tighten.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
TIP
A tight spoke will emit a clear, ringing tone; a
loose spoke will sound flat.
3-33
CHASSIS
WARNING
1 Securely support the vehicle so that there is
no danger of it falling over.
2. Check:
• Steering head
Grasp the bottom of the front fork legs and
gently rock the front fork.
Blinding/looseness Adjust the steering
head.
3. Remove:
Spoke nipple wrench (6–7) • Handlebar
90890-01521
Refer to “HANDLEBAR” on page 4-31.
Spoke nipple wrench (6–7)
YM-01521 • Upper bracket
Refer to “STEERING HEAD” on page 4-49.
4. Adjust:
Spokes
• Steering head
2.5 Nm (0.25 m·kgf, 1.8 ft·lbf)
T.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
R.
1. Check:
b. After loosening the ring nut “2” with a steer-
• Wheel(s)
ing nut wrench “3”, tighten it to the specified
Damage/out-of-round Replace.
EWA
torque.
WARNING TIP
Never attempt to make any repairs to the • Set the torque wrench at a right angle to the
wheel. steering nut wrench.
TIP • Move the steering to the left and right a couple
of times to check that it moves smoothly.
After replacing a tire or a wheel, always bal-
ance the wheel.
3
1. Check:
• Wheel bearings
Refer to “CHECKING THE FRONT WHEEL”
on page 4-4 and “CHECKING THE REAR
WHEEL” on page 4-8.
2
3-34
CHASSIS
• Clutch lever
R.
WARNING
Do not overtighten the lower ring nut.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
5. Install:
• Upper bracket
Refer to “STEERING HEAD” on page 4-49.
• Handlebar
Refer to “HANDLEBAR” on page 4-31.
3-35
ELECTRICAL SYSTEM
• Spark plug
CHECKING THE SPARK PLUG (with a spark plug cleaner or a wire brush)
EAS1SME114
1. Remove: 6. Measure:
• Seat • Spark plug gap “a”
• Air scoop (left/right) Out of specification Adjust the spark plug
Refer to “GENERAL CHASSIS” on page 4- gap.
1.
• Fuel tank “1” Spark plug gap
Refer to “FUEL TANK” on page 7-1. 0.7–0.8 mm (0.028–0.031 in)
ECA
NOTICE
Do not use too much force to pull the hose.
TIP
Remove the fuel tank, turn this 180 ° clockwise,
and put it in the frame “2” as shown.
1
1
7. Install:
• Spark plug
Spark plug
13 Nm (1.3 m·kgf, 9.4 ft·lbf)
T.
R.
2
TIP
2. Remove:
Before installing the spark plug, clean the spark
• Spark plug cap
plug and gasket surface.
• Spark plug
Refer to “CAMSHAFT” on page 5-11. 8. Install:
ECA
4. Check:
• Electrode
Damage/wear Replace the spark plug.
• Insulator
Abnormal color Replace the spark plug.
Normal color is medium-to-light tan.
1
3-36
ELECTRICAL SYSTEM
2. Attach:
• Timing light “1”
• Digital tachometer “2”
To the high tension code “3”.
Timing light
90890-03141
Timing light
YU-03141
Digital tachometer
90890-06760
Digital tachometer
YU-39951-B
2 3
3. Adjust:
• Engine idling speed
Refer to “ADJUSTING THE ENGINE
IDLING SPEED” on page 3-16.
4. Check:
• Ignition timing
Check whether the alignment mark “a” on
the left crankcase cover is within the firing
range “b” on the rotor.
Incorrect firing range Check rotor and
Crankshaft position sensor.
b a
5. Install:
• Timing mark accessing screw
Timing mark accessing screw
6 Nm (0.6 m·kgf, 4.3 ft·lbf)
T.
R.
3-37
ELECTRICAL SYSTEM
3-38
CHASSIS
GENERAL CHASSIS........................................................................................4-1
REMOVING THE LEFT SIDE COVER .......................................................4-2
REMOVING THE SEAT..............................................................................4-2
REMOVING THE NUMBER PLATE ...........................................................4-2
FRONT FORK.................................................................................................4-37
REMOVING THE FRONT FORK LEGS ...................................................4-39
DISASSEMBLING THE FRONT FORK LEGS .........................................4-39
CHECKING THE FRONT FORK LEGS....................................................4-40
ASSEMBLING THE FRONT FORK LEGS ...............................................4-41
INSTALLING THE FRONT FORK LEGS..................................................4-47
STEERING HEAD...........................................................................................4-49
REMOVING THE LOWER BRACKET......................................................4-50
CHECKING THE STEERING HEAD ........................................................4-50
INSTALLING THE STEERING HEAD ......................................................4-50
SWINGARM ....................................................................................................4-60
REMOVING THE SWINGARM.................................................................4-61
REMOVING THE BEARING.....................................................................4-61
CHECKING THE SWINGARM .................................................................4-61
INSTALLING THE SWINGARM ...............................................................4-62
EAS1SME116
TIP
This section is intended for those who have basic knowledge and skill concerning the servicing of
Yamaha motorcycles (e.g., Yamaha dealers, service engineers, etc.). Those who have little knowl-
edge and skill concerning servicing are requested not to undertake inspection, adjustment, disas-
sembly, or reassembly only by reference to this manual. It may lead to servicing trouble and
mechanical damage.
GENERAL CHASSIS
EAS1SME117
T.R
.
16 Nm (1.6 m•kgf, 12 ft•Ibf)
T .R
.
5 7
1
3
T .R
.
(2)
4
6
22 Nm (2.2 m•kgf, 16 ft •Ibf)
T .R
.
T .R
.
7 Rear fender 1
For installation, reverse the removal proce-
dure.
4-1
GENERAL CHASSIS
1. Remove: 1. Remove:
• Bolt (side cover) • Bolt (number plate)
• Side cover “1” • Number plate “1”
TIP TIP
Draw the left side cover “1” backward to re- • The projection “a” is inserted into the band of
move it because its projection “a” is inserted in the number plate. Pull the band off the projec-
the rear frame. tion before removal.
• Remove the clutch cable “2” from the cable
1 guide “b” on the number plate.
• The projection “c” on the lower bracket is in-
serted into the number plate. Remove the
number plate by pulling it off the projection.
a
TIP
The fuel tank cap cover and the seat are cou-
pled with each other with a plastic band.
When removing the seat, always remove the
fuel tank cap cover beforehand.
1. Remove:
• Fuel tank cap cover “1”
Refer to “FUEL TANK CAP” on page 1-17.
2. Remove:
• Seat “1”
4-2
FRONT WHEEL
FRONT WHEEL
EAS1SME121
T .R
.
3
21 Nm (2.1 m•kgf, 15 ft •Ibf)
T .R
.
1
5 6 New 2
7 1
T.R
.
LS 8
LS
New
(6)
4 7
6 5
LT 12 Nm (1.2 m•kgf, 8.7 ft •Ibf)
T .R
.
4 Front wheel 1
5 Collars 2
6 Oil seals 2
7 Bearing 2
8 Brake disc 1
For installation, reverse the removal proce-
dure.
4-3
FRONT WHEEL
TIP
1. Use a suitable stand to raise the front wheel A tight spoke will emit a clear, ringing tone; a
off the ground. loose spoke will sound flat.
EWA
WARNING 4. Tighten:
Securely support the vehicle so that there is • Spokes
no danger of it falling over. Refer to “CHECKING AND TIGHTENING
2. Remove: THE SPOKES” on page 3-33.
• Front wheel Spokes
CHECKING THE FRONT WHEEL
EAS1SME123
2.5 Nm (0.25 m·kgf, 1.8 ft·lbf)
T.
R.
1. Check:
• Front wheel axle TIP
Roll the front wheel axle on a flat surface. After tightening the spokes, measure the wheel
Bends Replace. runout.
5. Measure:
• Wheel radial runout “a”
• Wheel lateral runout “b”
Out of specification Repair/replace.
b
a
EWA
WARNING
Do not attempt to straighten a bent wheel
axle.
2. Check:
• Tire(s) Radial wheel runout limit
• Front wheel 2.0 mm (0.08 in)
Damage/wear Replace. Lateral wheel runout limit
Refer to “CHECKING THE TIRES” on page 2.0 mm (0.08 in)
3-33 and “CHECKING THE WHEELS” on
6. Check:
page 3-34.
• Collars
3. Check:
Damage/wear Replace.
• Spokes
7. Check:
Bend/damage Replace.
• Bearing
Loose Tighten.
Front wheel turns roughly or is loose Re-
Tap the spokes with a screwdriver.
place the wheel bearings.
• Oil seals
Damage/wear Replace.
4-4
FRONT WHEEL
NOTICE
1. Remove: Install the bearing by pressing its outer race
• Oil seals parallel.
• Bearings
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Clean the outside of the front wheel hub.
b. Remove the oil seals “1” with a flat-head
screwdriver.
TIP 4 New
To prevent damaging the wheel, place a rag “2” 3
between the screwdriver and the wheel sur- 2
face.
1
4 New
1
c. Remove the bearings with a bearing puller.
TIP
Use a socket “1” that matches the diameter of
the bearing outer race and that of the oil seal.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
1. Install:
• Bearing (left side) “1”
• Spacer “2” 2. Install:
• Bearing (right side) “3” • Brake disc “1”
• Oil seals “4” New • Brake disc bolt “2”
TIP Brake disc bolt
• Apply the lithium-soap-based grease to the 12 Nm (1.2 m·kgf, 8.7 ft·lbf)
T.
LOCTITE®
R.
4-5
FRONT WHEEL
3. Install: 3. Tighten:
• Collar “1” • Front wheel axle nut “1”
TIP Front wheel axle nut
Apply the lithium-soap-based grease on the oil 115 Nm (11.5 m·kgf, 83 ft·lbf)
T.
seal lip.
R.
ECA
NOTICE
1 Before tightening the front wheel axle nut,
push down hard on the handlebar(s) several
times and check if the front fork rebounds
smoothly.
LS
1
1. Install:
• Front wheel
TIP
Install the brake disc “1” between the brake
4. Tighten:
pads “2” correctly.
• Front wheel axle pinch bolt “1”
Front wheel axle pinch bolt
21 Nm (2.1 m·kgf, 15 ft·lbf)
T.
R.
2. Install:
• Front wheel axle “1” 1 1
TIP
Apply the lithium-soap-based grease to the
front wheel axle.
4-6
REAR WHEEL
REAR WHEEL
EAS1SME127
T .R
.
135 Nm (13.5 m•kgf, 98 ft•lbf)
(6)
T.R
LT
.
10
5
7
8
21 Nm (2.1 m•kgf, 15 ft •Ibf) 9
T .R
.
LS
(6)
42 Nm (4.2 m•kgf, 30 ft•Ibf)
T .R
.
6
(6) LS
5
3
9
7
2
LS
4
4 Rear wheel 1
5 Collars 2
7 Oil seals 2
8 Circlip 1
9 Bearing 3
10 Brake disc 1
4-7
REAR WHEEL
1. Use a suitable stand to raise the rear wheel • Radial wheel runout
off the ground. • Lateral wheel runout
EWA
4. Tighten: 1. Remove:
• Adjusting bolt “3” • Oil seals
• Bearing
Refer to “DISASSEMBLING THE FRONT
WHEEL” on page 4-5.
2 CHECKING AND REPLACING THE REAR
EAS1SME131
WHEEL SPROCKET
1. Check:
• Rear wheel sprocket
3
More than 1/4 tooth wear “a” Replace the
1
rear wheel sprocket and the drive sprocket
5. Remove: as a set.
• Rear wheel axle Bent tooth Replace the rear wheel
• Rear wheel sprocket and the drive sprocket as a set.
TIP
• Push the rear wheel forward and remove the
drive chain from the rear wheel sprocket.
• Do not depress the brake pedal with the rear
wheel removed.
1. Check:
• Rear wheel axle
• Rear wheel
• Bearing b. Correct
• Oil seals 1. Drive chain roller
Refer to “CHECKING THE FRONT WHEEL” 2. Rear wheel sprocket
on page 4-4. 2. Replace:
2. Check: • Rear wheel sprocket
• Tire(s) ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
• Rear wheel a. Remove the self-locking nuts and the rear
Damage/wear Replace. wheel sprocket.
Refer to “CHECKING THE TIRES” on page b. Clean the rear wheel drive hub with a clean
3-33 and “CHECKING THE WHEELS” on cloth, especially the surfaces that contact
page 3-34. the sprocket.
3. Check: c. Install the new rear wheel sprocket.
• Spokes
Refer to “CHECKING THE FRONT WHEEL” Rear wheel sprocket self-locking
nut
on page 4-4.
T.
4-8
REAR WHEEL
TIP
Tighten the self-locking nuts in stages and in a
crisscross pattern. 1
2. Install:
• Brake disc “1”
• Brake disc bolt “2”
Brake disc bolt
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
14 Nm (1.4 m·kgf, 10 ft·lbf)
T.
LOCTITE®
R.
ASSEMBLING THE REAR WHEEL
EAS1SME132
1. Install:
• Bearing (right side) “1” TIP
• Circlip “2” New Tighten the bolts in stages and in a crisscross
• Spacer “3” pattern.
• Bearing (left side) “4”
• Oil seals “5” New
TIP
• Apply the lithium-soap-based grease to the
bearing and the oil seal lip when installing.
• Install the bearing with seal facing outward.
• Right side of bearing shall be installed first.
• Install the oil seal with its manufacture’s
marks or numbers facing outward.
ECA
NOTICE 3. Install:
Install the bearing by pressing its outer race • Collar “1”
parallel. TIP
Apply the lithium-soap-based grease on the oil
5 2
seal lip.
1
LS LS
3 5
4
LS
TIP
Use a socket “1” that matches the diameter of
the bearing outer race and that of the oil seal.
INSTALLING THE REAR WHEEL
EAS1SME133
1. Install:
• Rear wheel
4-9
REAR WHEEL
TIP TIP
Install the brake disc “1” between the brake Temporarily tighten the nut (rear wheel axle) at
pads “2” correctly. this point.
3 1
2. Install: 5. Adjust:
• Drive chain “1” • Drive chain slack “a”
TIP Drive chain slack
Push the rear wheel “2” forward and install the 50.0–60.0 mm (1.97–2.36 in)
drive chain.
Refer to “ADJUSTING THE DRIVE CHAIN
SLACK” on page 3-28.
3. Install:
• Left drive chain puller “1”
6. Tighten:
• Rear wheel axle “2”
• Rear wheel axle nut “1”
TIP
• Install the left drive chain puller, and insert the Wheel axle nut
rear wheel axle from the left side. 135 Nm (13.5 m·kgf, 98 ft·lbf)
T.
R.
2
1
1
2
LS
4. Install:
• Right drive chain puller “1”
• Washer “2”
• Rear wheel axle nut “3”
4-10
FRONT BRAKE
FRONT BRAKE
EAS1SME134
T .R
.
28 Nm (2.8 m kgf, 20 ft lbf)
T .R
.
6 Nm (0.6 m kgf, 4.3 ft lbf)
T .R
.
3
9
2
8
7
5 4
2 Copper washers 2
6 Brake pads 2
4-11
FRONT BRAKE
T.
R.
1 2 S 4
S
3
BF
S
4 Bleed screw 1
For assembly, reverse the disassemble pro-
cedure.
4-12
FRONT BRAKE
T.R
. 8
5
6
6 Nm (0.6 m kgf, 4.3 ft lbf)
T .R
.
7
6 Nm (0.6 m kgf, 4.3 ft lbf)
T .R
.
9
1
2
30 Nm (3.0 m kgf, 22 ft lbf)
T .R
.
2 Union bolt 1
3 Copper washers 2
4-13
FRONT BRAKE
1
S
2
3 New
4
5 New
BF
2 Dust boot 1
3 Circlip 1
4 Washer 1
4-14
FRONT BRAKE
INTRODUCTION
EAS1SME135
EWA
Brake disc thickness limit
WARNING 2.5 mm (0.10 in)
If you need to disassemble the disc brake
components, observe the following precau- 4. Install:
tions. • Front wheel
• Never disassemble the brake components Refer to “FRONT WHEEL” on page 4-3.
unless absolutely necessary.
REMOVING THE FRONT BRAKE CALIPER
EAS1SME137
plastic parts.
• Handle brake fluid with special care not to IPER
let it enter your eyes so that you may not 1. Remove:
lost your eyesight. • Brake caliper piston “1”
• FIRST AID FOR BRAKE FLUID ENTERING • Brake caliper piston dust seal “2”
THE EYES: • Brake caliper piston seals “3”
• Flush with water for 15 minutes and get
1
immediate medical attention. 3
CHECKING THE FRONT BRAKE DISC
EAS1SME136
1. Remove:
• Front wheel
Refer to “FRONT WHEEL” on page 4-3.
2. Check:
• Front brake disc 2
Damage/galling Replace.
3. Measure: ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
• Brake disc thickness a. Blow compressed air into the brake hose
Measure the brake disc thickness at a few joint opening to force out the piston from the
different locations. brake caliper.
Out of specification Replace.
EWA
WARNING
• Cover the brake caliper piston with a rag.
Be careful not to get injured when the pis-
ton is expelled from the brake caliper.
• Never try to pry out the brake caliper pis-
ton.
4-15
FRONT BRAKE
PER
EWA
WARNING
• Before installation, clean and lubricate the
internal parts. Use new brake fluid for
cleaning and lubricating.
• Never use solvents on internal brake com-
ponents as they will cause the piston seals
to swell and distort.
b. Remove the brake caliper piston dust seal • When the brake caliper is disassembled,
and the brake caliper piston seal. replace the brake caliper piston seal and
the brake caliper piston dust seal with new
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
ones.
CHECKING THE FRONT BRAKE CALIPER
EAS1SME139
caliper piston.
• Brake caliper cylinder “2” 1. Clean:
Scratches/wear Replace the brake cali- • Brake caliper
per assembly. • Brake caliper piston seal
• Brake caliper body “3” • Brake caliper piston dust seal
Cracks/damage Replace the brake cali- • Brake caliper piston
per assembly. Use brake fluid for cleaning.
• Brake fluid delivery passages 2. Install:
(brake caliper body) • Brake caliper piston seals “1” New
Obstruction Blow out with compressed • Brake caliper piston dust seal “2” New
air.
EWA
WARNING
Always use new brake caliper piston seal
2 3 and brake caliper piston dust seal.
TIP
• Apply the silicone grease on the brake caliper
piston seal and brake caliper piston dust seal.
• Fit the brake caliper piston seal and the brake
caliper piston dust seal into the grooves in the
brake caliper correctly.
1 1
1
EWA
WARNING
When the brake caliper is disassembled, re-
place the brake caliper piston seal and the 1
brake caliper piston dust seal with new
ones.
2. Check: 2
• Brake caliper bracket
Crack/damage Replace.
2
4-16
FRONT BRAKE
3. Install: 2. Install:
• Brake caliper piston “1” • Front brake caliper
TIP • Brake pad spring
Apply the brake fluid on the piston outer sur- • Brake pad
face. • Brake pad pin
ECA
• Brake hose holder
NOTICE Brake pad pin
• Install the piston with its side “a” facing 17 Nm (1.7 m·kgf, 12 ft·lbf)
T.
the brake caliper.
R.
• Never force to insert. Refer to “CHECKING THE FRONT BRAKE
PADS” on page 3-24.
1 3. Tighten:
• Brake hose holder mounting bolt “1”
Brake hose holder mounting bolt
9 Nm (0.9 m·kgf, 6.5 ft·lbf)
T.
R.
TIP
a 1 Make sure that the brake hose holder “2” is in-
stalled with its upper end “a” aligned with the
paint “b” on the brake hose.
INSTALLING THE FRONT BRAKE CALIPER
EAS1SME142
1. Install: 2
• Front brake caliper bracket
• Front brake caliper
(temporarily) b
• Copper washers New
• Brake hose
• Union bolt a
WARNING
• Use only the designated brake fluid. Other
ECA
NOTICE
brake fluids may cause the rubber seals to
Make sure that the pipe portion “a” of the
deteriorate, causing leakage and poor
brake hose touches the projection “b” on
brake performance.
the brake caliper.
• Refill with the same type of brake fluid that
is already in the system. Mixing brake flu-
ids may result in a harmful chemical reac-
tion, leading to poor brake performance.
• When refilling, be careful that water does
not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
a the brake fluid and could cause vapor
b lock.
ECA
4-17
FRONT BRAKE
NOTICE
Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean 1
up any spilt brake fluid immediately.
5. Bleed:
• Brake system
Refer to “BLEEDING THE BRAKE SYS-
TEM” on page 3-22.
2
6. Check:
• Brake fluid level 2. Check:
The minimum level mark or below Add. • Brake master cylinder kit
Refer to “CHECKING THE BRAKE FLUID Damage/scratches/wear Replace.
LEVEL” on page 3-27. 3. Check:
7. Check: • Brake master cylinder reservoir cap
• Brake lever free play 4. Check:
Refer to “ADJUSTING THE FRONT • Brake hoses
BRAKE” on page 3-23. Cracks/damage/wear Replace.
• Brake lever operation
ASSEMBLING THE FRONT BRAKE MAS-
EAS1SME145
WARNING
Apply brake fluid to the cylinder cups and
CHECKING THE FRONT BRAKE MASTER
EAS1SME144
4-18
FRONT BRAKE
CYLINDER
1 2 1. Install:
• Brake master cylinder “1”
Brake master cylinder holder bolt
9 Nm (0.9 m·kgf, 6.5 ft·lbf)
T.
R.
3 TIP
• Install the front brake master cylinder holder
3. Install: with the “UP” mark facing up.
• Spring “1” • First, tighten the upper bolt, then the lower
Install to the brake master cylinder piston bolt.
“2”.
TIP
Install the spring with a smaller inside diameter
to the brake master cylinder piston.
2. Install:
• Copper washers New
• Brake hose
• Union bolt
4. Install: Brake hose union bolt
• Brake master cylinder kit “1” New 30 Nm (3.0 m·kgf, 22 ft·lbf)
T.
R.
4-19
FRONT BRAKE
NOTICE
Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.
4. Bleed:
• Brake system
Refer to “BLEEDING THE BRAKE SYS-
TEM” on page 3-22.
5. Check:
• Brake fluid level
The minimum level mark “a” or below
Add.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-27.
4-20
REAR BRAKE
REAR BRAKE
EAS1SME147
T .R
.
T.R
.
17 Nm (1.7 m•kgf, 12 ft •Ibf)
T .R
.
30 Nm (3.0 m•kgf, 22 ft •Ibf)
T .R
.
10 9 S
2
New 3
11 4
4-21
REAR BRAKE
2
3
BF
4-22
REAR BRAKE
T.
R.
T.
R.
T.
R.
7
1
8
9 2
10
5
4
Order Part name Q’ty Remarks
Drain.
Brake fluid Refer to “BLEEDING THE BRAKE SYSTEM”
on page 3-22.
1 Union bolt 1
2 Copper washers 2
3 Brake hose 1
4 Split pin 1
5 Washer 1
6 Pin 1
7 Brake master cylinder reservoir cap 1
8 Brake master cylinder reservoir diaphragm plate 1
9 Brake master cylinder reservoir diaphragm 1
10 Rear brake master cylinder 1
For installation, reverse the removal proce-
dure.
4-23
REAR BRAKE
BF
4 New
S 3
2 New
4-24
REAR BRAKE
INTRODUCTION
EAS1SME148
EWA
WARNING
If you need to disassemble the disc brake
components, observe the following precau-
tions.
• Never disassemble the brake components
unless absolutely necessary.
• If there is any problem with connections
on the hydraulic brake system, perform
the following jobs.
Disassemble the brake system, drain the Brake disc runout limit (as mea-
brake fluid, and clean it. After that, add a sured on wheel)
suitable amount of brake fluid. Then, bleed 0.15 mm (0.0059 in)
it after reassembly.
5. Adjust:
• Use only brake fluid for washing internal
• Brake disc deflection
brake components.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
• Use new brake fluid for cleaning the brake
a. Remove the brake disc.
components.
b. Turn the mounted position of the brake disc
• Immediately wipe off the spilled brake fluid
by one bolt hole.
to avoid damage to painted surfaces or
c. Install the brake disc.
plastic parts.
• Handle brake fluid with special care not to TIP
let it enter your eyes so that you may not Tighten the brake disc bolts in stages and in a
lost your eyesight. crisscross pattern.
• FIRST AID FOR BRAKE FLUID ENTERING
THE EYES:
• Flush with water for 15 minutes and get
immediate medical attention.
1. Remove:
• Rear wheel
Refer to “REAR WHEEL” on page 4-7.
2. Check:
• Brake disc
Damage/galling Replace. Brake disc bolt
3. Measure: 14 Nm (1.4 m·kgf, 10 ft·lbf)
T.
4-25
REAR BRAKE
REMOVING THE REAR BRAKE CALIPER CHECKING THE REAR BRAKE CALIPER
EAS1SME150 EAS1SME152
TIP 1. Check:
Before disassembling the brake caliper, drain • Brake caliper piston “1”
the brake fluid from the entire brake system. Rust/scratches/wear Replace the brake
caliper piston.
1. Remove: • Brake caliper cylinder “2”
• Union bolt Scratches/wear Replace the brake cali-
• Copper washers per assembly.
• Brake hose • Brake caliper body “3”
TIP Cracks/damage Replace the brake cali-
Put the end of the brake hose into a container per assembly.
and pump out the brake fluid. • Brake fluid delivery passages
(brake caliper body)
DISASSEMBLING THE REAR BRAKE CALI-
EAS1SME151
1 3
2 3 EWA
WARNING
When the brake caliper is disassembled, re-
place the brake caliper piston seal and the
brake caliper piston dust seal with new
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ ones.
a. Blow compressed air into the brake hose
2. Check:
joint opening to force out the piston from the
brake caliper. • Brake caliper bracket
EWA Crack/damage Replace.
WARNING
ASSEMBLING THE REAR BRAKE CALIPER
EAS1SME153
4-26
REAR BRAKE
INSTALLING THE BRAKE CALIPER PISTON INSTALLING THE REAR BRAKE CALIPER
EAS1SME154 EAS1SME155
1. Clean: 1. Install:
• Brake caliper • Rear brake caliper
• Brake caliper piston seal • Rear brake caliper bracket
• Brake caliper piston dust seal 2. Install:
• Brake caliper piston • Rear wheel
Use brake fluid for cleaning. Refer to “REAR WHEEL” on page 4-7.
2. Install: • Copper washers New
• Brake caliper piston seals “1” New • Brake hose
• Brake caliper piston dust seal “2” New • Union bolt
EWA
T.
R.
and brake caliper piston dust seal. EWA
TIP WARNING
• Apply the silicone grease on the brake caliper Proper brake hose routing is essential to in-
piston seal and brake caliper piston dust seal. sure safe vehicle operation.
• Fit the brake caliper piston seals and brake
ECA
NOTICE
caliper piston dust seals onto the slot on
Make sure that a bend in its pipe portion “a”
brake caliper correctly.
is directed as shown and the brake hose
touches the projection “b” on the brake cal-
iper.
2
b
3. Install:
• Brake caliper piston “1” b a
TIP 3. Install:
Apply the brake fluid on the piston outer sur- • Brake pad springs
face. • Brake pads
ECA
• Brake pad pin
NOTICE • Brake pad pin plug
• Install the piston with its side “a” facing
the brake caliper. Brake pad pin
17 Nm (1.7 m·kgf, 12 ft·lbf)
• Never force to insert.
T.
4-27
REAR BRAKE
WARNING
• Use only the designated brake fluid. Other CYLINDER
brake fluids may cause the rubber seals to TIP
deteriorate, causing leakage and poor Before removing the rear brake master cylin-
brake performance. der, drain the brake fluid from the entire brake
• Refill with the same type of brake fluid that system.
is already in the system. Mixing brake flu-
1. Remove:
ids may result in a harmful chemical reac-
• Union bolt
tion, leading to poor brake performance.
• Copper washers
• When refilling, be careful that water does
• Brake hose
not enter the brake fluid reservoir. Water
will significantly lower the boiling point of TIP
the brake fluid and could cause vapor To drain any remaining brake fluid, place a con-
lock. tainer under the master cylinder and the end of
ECA the brake hose.
NOTICE
Brake fluid may damage painted surfaces CHECKING THE REAR BRAKE MASTER
EAS1SME157
1 2
2. Check:
• Brake master cylinder kit
Damage/wear Replace.
a 3. Check:
7. Check: • Master cylinder reservoir cap
• Brake pedal operation Crack/damage Replace.
A softy or spongy feeling Bleed the brake • Brake master cylinder reservoir diaphragm
system. holder
Refer to “BLEEDING THE BRAKE SYS- • Brake master cylinder reservoir diaphragm
TEM” on page 3-22. Crack/damage Replace.
4. Check:
• Brake hoses
Cracks/damage/wear Replace.
4-28
REAR BRAKE
CYLINDER
EWA
WARNING
• Before installation, all internal brake com-
ponents should be cleaned and lubricated 1 2
with clean or new brake fluid.
• Never use solvents on internal brake com-
ponents.
WARNING
• Use circlip pliers to install the circlip.
Apply brake fluid to the cylinder cups and
install them as shown. Wrong orientation in
installation causes poor braking perfor-
mance.
1 New 3 New
4
2
1
2
3
CYLINDER
1. Install:
• Copper washers New
2 • Brake hose
• Union bolt
1 Brake hose union bolt
30 Nm (3.0 m·kgf, 22 ft·lbf)
T.
R.
EWA
3 WARNING
Proper brake hose routing is essential to in-
sure safe vehicle operation.
3. Install: ECA
4-29
REAR BRAKE
a
2. Pour brake fluid to the brake fluid reservoir 5. Check:
up to the specified level. • Brake pedal operation
A softy or spongy feeling Bleed the brake
Specified brake fluid
system.
DOT 4
Refer to “BLEEDING THE BRAKE SYS-
EWA
TEM” on page 3-22.
WARNING
• Use only the designated brake fluid. Other
brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.
• Refill with the same type of brake fluid that
is already in the system. Mixing brake flu-
ids may result in a harmful chemical reac-
tion, leading to poor brake performance.
• When refilling, be careful that water does
not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
the brake fluid and could cause vapor
lock.
ECA
NOTICE
Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.
3. Bleed:
• Brake system
Refer to “BLEEDING THE BRAKE SYS-
TEM” on page 3-22.
4. Check:
• Brake fluid level
The minimum level mark “a” or below
Add.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-27.
4-30
HANDLEBAR
HANDLEBAR
EAS1SME160
9 Tube guide 1
10 Collars 1
11 Left grip 1
13 Handlebar 1
4-31
HANDLEBAR
15 Damper 4
For installation, reverse the removal proce-
dure.
4-32
HANDLEBAR
TIP
1. Stand the vehicle upright on a level surface. • Install the lower handlebar holders with them
EWA13120
NOTICE
• First, tighten the bolts on the front side of
the upper handlebar holder, and then on
the rear side.
• Turn the handlebar all the way to the left
CHECKING THE HANDLEBAR and right. If there is any contact with the
EAS1SME162
WARNING
Do not attempt to straighten a bent handle- 1
bar as this may dangerously weaken it.
1
1. Stand the vehicle upright on a level surface.
EWA13120
WARNING
Securely support the vehicle so that there is
no danger of it falling over. a
2. Install:
• Damper “1”
• Lower handlebar holders “2” (temporarily)
• Handlebar “3”
• Upper handlebar holders “4”
Upper handlebar holder bolt
28 Nm (2.8 m·kgf, 20 ft·lbf)
T.
R.
4-33
HANDLEBAR
4. Install:
• Handlebar grip “1”
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
3 a. Slightly coat the handlebar left end with a
rubber adhesive.
4 b. Install the handlebar grip on the handlebar
by pressing the grip from the left side.
c. Wipe off any excess adhesive with a clean
cloth.
EWA13120
WARNING
Securely support the vehicle so that there is
no danger of it falling over.
TIP
Install the handlebar grip to the handlebar so
that the line “a” between the two arrow marks
faces straight upward.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
5. Install:
• Engine stop switch “1”
• Clutch lever “2”
• Clutch lever holder “3”
• Clamp “4”
Engine stop switch screw
0.5 Nm (0.05 m·kgf, 0.36 ft·lbf)
T.
TIP
3. Tighten: • The engine stop switch, the clutch lever, and
• Lower handlebar holder nut the clutch lever holder should be installed ac-
Lower handlebar holder nut cording to the dimensions shown.
40 Nm (4.0 m·kgf, 29 ft·lbf) • Pass the engine stop switch lead through the
middle of the clutch lever holder.
T.
R.
4-34
HANDLEBAR
6. Install: 8. Install:
• Right grip “1” • Throttle cables “1”
• Collar “2” TIP
Apply adhesive to the tube guide “3”. Slightly coat the end of throttle cable and inside
TIP of throttle grip with lithium-soap-based grease.
• Before applying the adhesive, wipe off grease Then, mount the throttle grip onto the handle-
or oil on the tube guide surface “a” with a lac- bar.
quer thinner.
• Install the grip to the tube guide so that the
grip match mark “b” and tube guide slot “c”
form the angle as shown.
9. Install:
• Throttle cable housings “1”
• Screw (throttle cable housings) “2”
Screw (throttle cable housings)
3.8 Nm (0.38 m·kgf, 2.8 ft·lbf)
64
T.
R.
b EWA1DX5001
WARNING
After tightening the throttle cable housing
1
screws, check that the throttle grip “3”
moves smoothly. If it does not, retighten the
c screws for adjustment.
3
7. Install:
• Collar “1”
• Rubber cover “2”
• Throttle grip “3”
TIP
Apply the lithium soap base grease on the
throttle grip sliding surface.
4-35
HANDLEBAR
12.Install:
• Clutch cable “1”
TIP
Before installation, apply the lithium-soap-
based grease to the clutch cable end.
LS 1
10.Install:
• Rubber cover “1”
• Cover (throttle cable housings) “2”
13.Adjust:
• Clutch lever free play
Refer to “ADJUSTING THE CLUTCH LE-
VER FREE PLAY” on page 3-10.
Clutch lever free play
7.0–12.0 mm (0.28–0.47 in)
11.Install: 14.Adjust:
• Front brake master cylinder assembly “1” • Throttle grip free play
• Front brake master cylinder holder “2” Refer to “ADJUSTING THE THROTTLE
• Bolt (brake master cylinder holder) “3” GRIP FREE PLAY” on page 3-11.
Front brake master cylinder hold- Throttle grip free play
er bolt 3.0–5.0 mm (0.12–0.20 in)
T.
TIP
• Install the brake master cylinder holder with
the “UP” mark facing up.
• Install in order for the top of the front brake
master cylinder assembly to be level.
• First, tighten the upper bolt, then the lower
bolt.
4-36
FRONT FORK
FRONT FORK
EAS1SME164
T .R
.
4
T .R
.
1
4-37
FRONT FORK
T .R
.
29 Nm (2.9 m•kgf, 21 ft •Ibf)
T .R
.
New
7 13
New New
6
2
New 12
8
9
11 New
10
LT
4 New
1 New
28 Nm (2.8 m•kgf, 20 ft•Ibf)
T .R
LS
.
T.R
.
4-38
FRONT FORK
NOTICE
1. Use a suitable stand to raise the front wheel
Do not remove the locknut as the damper
off the ground. rod may go into the damper assembly and
not be taken out.
EWA
WARNING
Securely support the vehicle so that there is Cap bolt ring wrench
no danger of it falling over. 90890-01501
TIP Cap bolt ring wrench
YM-01501
Record the adjusting screw setting position be-
fore loosening the adjuster and the base valve.
2. Loosen:
• Upper bracket pinch bolts
• Damper assembly 1
• Lower bracket pinch bolts
EWA
WARNING
4
Before loosening the upper and lower 3
bracket pinch bolts, support the front fork 2
leg.
TIP
3. Remove:
• Dust seal “1”
Before removing the front fork leg from the ve- • Oil seal clip “2”
hicle, loosen the damper assembly “1” with the (with a flat-head screwdriver)
cap bolt ring wrench “2”.
ECA
NOTICE
Do not scratch the inner tube.
Cap bolt ring wrench
90890-01501
Cap bolt ring wrench 1
YM-01501
1 2
4. Remove:
• Inner tube “1”
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Push in slowly “a” the inner tube just before
3. Remove: it bottoms out and then pull it back quickly
• Front fork leg (s) “b”.
b. Repeat this step until the inner tube can be
DISASSEMBLING THE FRONT FORK LEGS pulled out from the outer tube.
EAS1SME166
1. Drain:
• Fork oil
2. Remove:
• Adjuster “1”
(from the inner tube)
TIP
• While compressing the inner tube “2”, set the
cap bolt ring wrench “4” between the inner
tube and locknut “3”.
• Hold the locknut and remove the adjuster.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
4-39
FRONT FORK
5. Remove:
• Base valve “1”
(from the damper assembly)
TIP
Hold the damper assembly with the cap bolt
ring wrench “2” and use the cap bolt wrench “3”
to remove the base valve.
1. Check:
• Inner tube surface “a”
Scratches Repair or replace.
Use #1000 grit wet sandpaper. 4. Check:
Damaged oil lock piece Replace. • Damper assembly “1”
• Inner tube bends Bend/damage Replace.
Out of specification Replace. • O-ring “2”
Use the dial gauge “1”. Wear/damage Replace.
ECA
4-40
FRONT FORK
1
1
2 2 New
5. Check:
ASSEMBLING THE FRONT FORK LEGS
EAS1SME168
NOTICE
• Be sure to use the recommended oil. Other
oils may have an adverse effect on front
fork performance.
• When disassembling and assembling the
front fork leg, take care not to allow any
foreign material to enter the front fork.
3. After filling, pump the damper assembly “1”
7. Check: slowly up and down (about 200 mm (7.9 in)
• Adjuster “1” stroke) several times to bleed the damper
• O-rings “2” New assembly of air.
Wear/damage Replace. TIP
Avoid excessive full stroke. A stroke of 200 mm
(7.9 in) or more will cause air to enter. In this
case, repeat the steps 1 to 3.
4-41
FRONT FORK
6. Loosen:
• Compression damping force adjuster “1”
TIP
• Before loosening the damping force adjuster,
record the setting position.
1 • Unless the damping force adjuster is fully
loosened, correct damping characteristic can-
not be obtained after installation.
4. Measure:
• Oil level (left and right) “a” 1
Out of specification Regulate.
Standard oil level
145–148 mm (5.71–5.83 in)
From top of fully stretched
damper assembly.
7. Install:
• Base valve “1”
a (to the damper assembly “2”)
TIP
First bring the damper rod pressure to a maxi-
mum. Then install the base valve while releas-
ing the damper rod pressure.
8. Check:
5. Tighten: • Damper assembly
• Locknut “1” Not fully stretched Repeat the steps 1 to
TIP 7.
Fully finger tighten the locknut onto the damper 9. Tighten:
assembly. • Base valve “1”
Base valve
28 Nm (2.8 m·kgf, 20 ft·lbf)
T.
R.
TIP
Hold the damper assembly with the cap bolt
ring wrench “2” and use the cap bolt wrench “3”
to tighten the base valve.
4-42
FRONT FORK
3
13.Check:
2 • Damper assembly smooth movement
1 Tightness/binding/rough spots Repeat
the steps 1 to 12.
14.Install:
• Dust seal “1” New
• Oil seal clip “2”
1 • Oil seals “3” New
• Washer “4”
• Outer tube bushing “5” New
(to the inner tube “6”)
ECA32D1010
NOTICE
11.While protecting the damper assembly “1”
with a cloth and compressing fully, allow ex- Make sure that the numbered side of the oil
cessive oil to overflow on the base valve seal faces bottom side.
side.
ECA32D1010 TIP
NOTICE • Apply the lithium-soap-based grease on the
Take care not to damage the damper assem- dust seal lip and oil seal lip.
bly. • Apply the fork oil on the inner tube.
• When installing the oil seal, use vinyl seat “a”
with fork oil applied to protect the oil seal lip.
4-43
FRONT FORK
15.Install:
• Inner tube bushing “1” New
TIP
Install the inner tube bushing onto the slot on
inner tube.
18.Install:
• Oil seals “1” New
TIP
Using a fork seal driver “2”, press the oil seal in
until the stopper ring groove fully appears.
16.Install:
Fork seal driver
• Outer tube “1”
90890-01502
(to the inner tube “2”) Fork seal driver (48)
YM-A0948
17.Install:
• Inner tube bushing “1”
• Washer “2” 19.Install:
(to the outer tube) • Oil seal clip “1”
TIP TIP
Press the inner tube bushing into the outer tube Fit the oil seal clip correctly in the groove in the
with fork seal driver “3”. outer tube.
4-44
FRONT FORK
2
1 a
20.Install: 23.Install:
• Dust seal “1” New • Collar “1”
TIP • Fork spring “2”
Apply lithium-soap-based grease on the inner (to the damper assembly “3”)
tube. TIP
Install the collar with its larger dia. end “a” fac-
ing the fork spring.
1 2
3 a
21.Check:
• Inner tube smooth movement
Tightness/binding/rough spots Repeat 24.Install:
the steps 14 to 20. • Damper assembly “1”
(to the inner tube “2”)
ECA32D1010
NOTICE
Allow the damper assembly to slide slowly
down the inner tube until it contacts the bot-
tom of the inner tube. Be careful not to dam-
age the inner tube.
22.Measure:
• Distance “a”
1
Out of specification Turn into the locknut.
Distance “a”
16 mm (0.63 in) or more
Between the damper assembly 2
“1” bottom and locknut “2” bot-
tom.
4-45
FRONT FORK
25.Loosen:
• Rebound damping force adjuster “1” Gap “a” between the adjuster and
TIP
the locknut
0.5–1.0 mm (0.02–0.04 in)
• Before loosening the damping force adjuster,
record the setting position. TIP
• Unless the damping force adjuster is fully If it is installed with a gap out of specification,
loosened, correct damping characteristic can- correct damping force cannot be obtained.
not be obtained after installation.
1
1
28.Tighten:
26.Install: • Adjuster (locknut) “1”
• Damper adjusting rod “1”
• Copper washer “2” New Adjuster (locknut)
• Adjuster “3”
T.
R. 29 Nm (2.9 m·kgf, 21 ft·lbf)
(to the damper assembly “4”)
TIP
TIP
Hold the locknut “2” and tighten the adjuster.
• While compressing the inner tube “5”, set the
cap bolt ring wrench “7” between the inner
tube and locknut “6”.
• Fully finger tighten the adjuster onto the
damper assembly.
29.Install:
• Adjuster “1”
(to the inner tube)
Adjuster
55 Nm (5.5 m·kgf, 40 ft·lbf)
T.
LOCTITE®
R.
27.Measure: 1
LT
• Gap “a” between the adjuster “1” and the
locknut “2”
Out of specification Retighten and read-
just the locknut.
4-46
FRONT FORK
30.Fill:
• Front fork leg
Recommended oil
Yamaha Suspension Oil S1
1
Standard oil amount
335 cm3 (11.33 US oz, 11.82
lmp.oz) (USA) (CAN) (JPN)
(AUS) (NZL) (ZAF)
340 cm3 (11.50 US oz, 12.00
lmp.oz) (EUR)
Extent of adjustment
300–365 cm3 (10.14–12.34 US INSTALLING THE FRONT FORK LEGS
EAS1SME169
NOTICE TIP
• Be sure to use the recommended oil. Other • Temporarily tighten the pinch bolts (lower
oils may have an adverse effect on front bracket).
fork performance. • Do not tighten the pinch bolts (upper bracket)
• When disassembling and assembling the yet.
front fork leg, do not allow any foreign ma-
terial to enter the front fork.
2. Tighten:
• Damper assembly “1”
31.Install: Damper assembly
• Damper assembly “1” 30 Nm (3.0 m·kgf, 22 ft·lbf)
(to the outer tube)
T.
R.
TIP TIP
Temporarily tighten the damper assembly. Use the cap bolt ring wrench “2” to tighten the
damper assembly.
32.Install:
• Protector guide “1”
2
4-47
FRONT FORK
3. Adjust:
• Front fork top end “a” 1
Front fork top end (standard) “a”
5 mm (0.20 in)
2
6. Adjust:
• Rebound damping force
TIP
Turn in the damping adjuster “1” finger-tight
and then turn out to the originally set position.
4. Tighten:
• Pinch bolt (upper bracket) “1”
Upper bracket pinch bolts
21 Nm (2.1 m·kgf, 15 ft·lbf)
1
T.
R.
EWA33DD044
WARNING
7. Adjust:
Tighten the lower bracket to specified • Compression damping force
torque. If torqued too much, it may cause
TIP
the front fork to malfunction.
Turn in the damping adjuster “1” finger-tight
and then turn out to the originally set position.
1
2 1
5. Install:
• Protector “1”
• Bolt (protector) “2”
Bolt (protector)
5 Nm (0.5 m·kgf, 3.6 ft·lbf)
T.
R.
4-48
STEERING HEAD
STEERING HEAD
EAS1SME170
T .R
.
145 Nm (14.5 m kgf, 105 ft lbf)
T .R
.
21 Nm (2.1 m kgf, 15 ft lbf) LS
T .R
2
.
3
LS 4
6
5
7
8
1
10
LS
4-49
STEERING HEAD
NOTICE
1. Use a suitable stand to raise the front wheel If the bearing race is not installed properly,
off the ground. the steering head pipe could be damaged.
EWA
WARNING TIP
Securely support the vehicle so that there is
Always replace the bearing and the bearing
no danger of it falling over.
race as a set.
2. Remove:
• Ring nut “1”
TIP
Remove the ring nut with the steering nut
wrench “2”.
WARNING
Securely support the lower bracket so that
there is no danger of it falling.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
4. Check:
• Upper bracket
• Lower bracket
(along with the steering stem)
CHECKING THE STEERING HEAD
EAS1SME172
Bends/cracks/damage Replace.
1. Wash with kerosene:
INSTALLING THE STEERING HEAD
EAS1SME173
• Bearing
• Bearing races 1. Install:
2. Check: • Lower bearing “1”
• Bearing TIP
• Bearing races Apply the lithium soap base grease on the dust
Damage/pitting Replace. seal lip and bearing inner circumference.
3. Replace:
• Bearing
• Bearing races
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the bearing race from the steering
head pipe with a long rod “1” and a hammer.
b. Remove the bearing race from the lower
bracket with a chisel “2” and a hammer.
c. Install a new bearing race.
ECA
4-50
STEERING HEAD
2. Install:
• Bearing races
• Upper bearing “1”
• Bearing race cover “2”
TIP
Apply the lithium soap base grease on the
bearing and bearing race cover lip.
3. Install:
• Lower bracket “1”
TIP
Apply the lithium soap base grease on the
bearing, the portion “a” and thread of the steer-
ing stem.
6. Install:
• Washer “1”
LS
a
LS
4. Install:
• Steering ring nut “1”
7. Install:
Steering ring nut • Front fork “1”
7 Nm (0.7 m·kgf, 5.1 ft·lbf) • Upper bracket “2”
T.
R.
TIP
TIP • Temporarily tighten the pinch bolts (lower
Install the steering nut with its stepped side “a” bracket).
facing downward. • Do not tighten the pinch bolts (upper bracket)
Tighten the steering ring nut with a steering yet.
nut wrench “2”.
Refer to “CHECKING AND ADJUSTING
THE STEERING HEAD” on page 3-34.
4-51
STEERING HEAD
11.Tighten:
• Pinch bolt (upper bracket) “1”
Upper bracket pinch bolts
21 Nm (2.1 m·kgf, 15 ft·lbf)
T.
R.
• Pinch bolt (lower bracket) “2”
Lower bracket pinch bolts
21 Nm (2.1 m·kgf, 15 ft·lbf)
T.
R.
EWA33DD049
8. Install: WARNING
• Steering stem nut “1” Tighten the lower bracket to specified
Steering stem nut torque. If torqued too much, it may cause
145 Nm (14.5 m·kgf, 105 ft·lbf) the front fork to malfunction.
T.
R.
TIP 1
Apply the lithium soap base grease to the con-
tact surface of the steering stem nut when in-
stalling.
2
4-52
REAR SHOCK ABSORBER ASSEMBLY
16 15 New
LS
14 13 New
M 12
LS
9 6
4 10
11
5 10
9
M 1
4-53
REAR SHOCK ABSORBER ASSEMBLY
16 15 New
LS
14 13 New
M 12
LS
9 6
4 10
11
5 10
9
M 1
4-54
REAR SHOCK ABSORBER ASSEMBLY
M
4
5
M
4 5
6
1
5 6 4
5
M
6
3
6 6
4 5
4 2 M
4 3
M
M
2 Connecting arm 1
3 Collars 3
4 Oil seals 6
5 Washers 8
6 Bearing 6
For assembly, reverse the disassemble pro-
cedure.
4-55
REAR SHOCK ABSORBER ASSEMBLY
WARNING
EWA
ER
Before disposing the rear shock absorber, be
sure to extract the nitrogen gas from valve “1”.
EWA
WARNING
• Wear protective glasses to prevent your 1
eyes from damage due to possible gas or
3. Remove:
metal chips scattered.
• Rear shock absorber assembly upper bolt
• To dispose of a damaged or a worn-out
• Rear shock absorber assembly
rear shock absorber, take the unit to your
Yamaha dealer for this disposal proce- REMOVING THE BEARING
EAS1SME178
dure. 1. Remove:
• Stopper ring (upper bearing) “1”
TIP
Press in the bearing while pressing its outer
race and remove the stopper ring.
ASSEMBLY
1. Use a suitable stand to raise the rear wheel
off the ground.
EWA
4-56
REAR SHOCK ABSORBER ASSEMBLY
3. Remove:
• Lower bearing “1” 1. Lubricate:
TIP • Oil seals
• Bearing
Remove the bearing by pressing its outer race.
• Spacers
• Washers
• Collars
Recommended lubricant
Molybdenum disulfide grease
2. Install:
• Bearing “1”
• Washer “2”
1 • Oil seals “3” New
(to relay arm “4”)
CHECKING THE REAR SHOCK ABSORBER
EAS1SME179
4-57
REAR SHOCK ABSORBER ASSEMBLY
TIP
2 3 Install the dust seals with their lips facing in-
1 ward.
a
Installed depth “a”
a 4.25 mm (0.17 in)
1
2
ER ASSEMBLY
1. Lubricate:
• Bearing (lower side)
• Dust seal
• Collars
• Bushing
5. Lubricate:
Recommended lubricant • Connecting arm and frame bolt
Molybdenum disulfide grease • Relay arm and connecting arm bolt
ECA1DX1012
• Relay arm and swingarm bolt
NOTICE (circumference and threaded portion)
Do not apply the grease to the bearing outer • Rear shock absorber assembly upper bolt
race because it will wear the rear shock ab- • Rear shock absorber assembly lower bolt
sorber surface on which the bearing is Recommended lubricant
press fitted. Molybdenum disulfide grease
2. Lubricate:
• O-ring 6. Install:
• Rear shock absorber assembly
Recommended lubricant TIP
Molybdenum disulfide grease
• When installing the rear shock absorber as-
3. Install: sembly, lift up the swingarm.
• Bearing • Install the rear shock absorber assembly up-
• Stopper ring New per bolt, and connecting arm bolt (frame side)
(to rear shock absorber assembly (upper from the right.
side)) • Install the rear shock absorber assembly low-
er bolts, connecting arm bolt (relay arm side),
TIP
and relay arm bolt (swingarm side) from the
• Install the bearing parallel until the stopper left.
ring groove appears by pressing its outer
race. 7. Tighten:
• After installing the stopper ring, push back the • Rear shock absorber assembly upper bolt
bearing unit it contacts the stopper ring. Rear shock absorber assembly
4. Install: upper bolt
T.
• Bearing “1”
• Bushing “2” • Connecting arm bolt (frame side)
• Collar “3”
• Dust seal “4” Connecting arm bolt (frame side)
(to rear shock absorber assembly (lower 80 Nm (8.0 m·kgf, 58 ft·lbf)
T.
R.
side))
4-58
REAR SHOCK ABSORBER ASSEMBLY
4-59
SWINGARM
SWINGARM
EAS1SME183
2
1 3
6
T.R
.
6 6
4 3
2
4
Drive chain
1 Collars 2
2 Oil seals 2
3 Thrust bearing 2
4 Bushing 2
5 Oil seals 2
6 Bearing 4
4-60
SWINGARM
WARNING
Securely support the vehicle so that there is
no danger of it falling over.
2. Measure:
• Swingarm side play
• Swingarm vertical movement
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
CHECKING THE SWINGARM
EAS1SME186
• Pivot shaft
b. Measure the swingarm side play “a” by mov- Roll the pivot shaft on a flat surface.
ing the swingarm from side to side. Bends Replace.
c. If the swingarm side play is out of specifica- EWA
4-61
SWINGARM
1. Lubricate:
• Bearing
• Collars
• Spacers
• Oil seal New
• Pivot shaft
Recommended lubricant
Molybdenum disulfide grease
2. Install:
• Bearing “1”
• Oil seals “2” New
(to the swingarm)
Installed depth “a”
0–0.5 mm (0–0.02 in)
Installed depth “b”
6.5 mm (0.26 in)
TIP
First install the outer and then the inner bear-
ings to a specified depth from inside.
a a a a
2 New 2 New 2 New
1 1
b b
3. Install:
• Swingarm
Pivot shaft nut
85 Nm (8.5 m·kgf, 61 ft·lbf)
T.
R.
TIP
Install the pivot shaft from the right.
4. Install:
• Rear wheel
Refer to “REAR WHEEL” on page 4-7.
5. Adjust:
• Drive chain slack
Refer to “ADJUSTING THE DRIVE CHAIN
SLACK” on page 3-28.
Drive chain slack
50.0–60.0 mm (1.97–2.36 in)
4-62
CHAIN DRIVE
CHAIN DRIVE
EAS1SME188
T .R
.
1 Drive chain 1
For installation, reverse the removal proce-
dure.
4-63
CHAIN DRIVE
WARNING
Securely support the vehicle so that there is
no danger of it falling over.
2. Remove:
• Joint clip
• Drive chain joint “1”
• Drive chain “2” TIP
• When measuring a 15-link section of the drive
chain, make sure that the drive chain is taut.
• Perform this procedure 2–3 times, at a differ-
ent location each time.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
2. Check:
• Drive chain
Stiffness Clean, lubricate, or replace.
1. Measure:
• 15-link section of the drive chain
Out of specification Replace the drive
chain.
15-link length limit
242.8 mm (9.56 in)
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ 3. Clean:
a. Measure the length “a” between the inner • Drive chain
sides of the pins and the length “b” between ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
the outer sides of the pins on a 15-link sec- a. Wipe the drive chain with a clean cloth.
tion of the drive chain as shown in the illus- b. Put the drive chain in kerosene and remove
tration. any remaining dirt.
c. Remove the drive chain from the kerosene
and completely dry it.
4-64
CHAIN DRIVE
WARNING
When installing the joint clip, always keep
the direction as shown in the figure.
5. Lubricate:
• Drive chain
CHECKING THE DRIVE SPROCKET
EAS1SME191
1. Check: 2. Lubricate:
• Drive sprocket • Drive chain
More than 1/4 tooth wear “a” Replace the 3. Install:
drive sprocket and the rear wheel sprocket • Drive sprocket
as a set. • Lock washer New
Bent tooth Replace the drive sprocket • Drive sprocket nut
and the rear wheel sprocket as a set. Refer to “ENGINE REMOVAL” on page 5-1.
Drive sprocket nut
75 Nm (7.5 m·kgf, 54 ft·lbf)
T.
R.
ECA1DX1014
NOTICE
Never install a new drive chain onto worn
drive sprockets; this will dramatically short-
en the drive chain’s life.
4. Adjust:
• Drive chain slack
b. Correct Refer to “ADJUSTING THE DRIVE CHAIN
1. Drive chain roller SLACK” on page 3-28.
2. Drive sprocket
Drive chain slack
CHECKING THE REAR WHEEL SPROCKET
EAS1SME192
NOTICE
A drive chain that is too tight will overload
EAS1SME193
4-65
CHAIN DRIVE
4-66
ENGINE
ENGINE REMOVAL..........................................................................................5-1
REMOVING THE SILENCER .....................................................................5-6
REMOVING THE EXHAUST PIPE 2..........................................................5-6
REMOVING THE DRIVE SPROCKET .......................................................5-6
REMOVING THE ENGINE .........................................................................5-7
CHECKING THE SILENCER AND EXHAUST PIPE..................................5-7
CHANGING THE SILENCER FIBER..........................................................5-7
INSTALLING THE ENGINE........................................................................5-8
INSTALLING THE BRAKE PEDAL.............................................................5-9
INSTALLING THE DRIVE SPROCKET......................................................5-9
INSTALLING THE EXHAUST PIPE AND MUFFLER ...............................5-10
CAMSHAFT ....................................................................................................5-11
REMOVING THE CAMSHAFT .................................................................5-13
CHECKING THE CAMSHAFT..................................................................5-14
CHECKING THE TIMING CHAIN AND CAMSHAFT SPROCKET...........5-15
CHECKING THE TIMING CHAIN TENSIONERS ....................................5-15
CHECKING THE DECOMPRESSION SYSTEM ......................................5-16
INSTALLING THE CAMSHAFTS .............................................................5-16
CYLINDER HEAD...........................................................................................5-18
REMOVING THE CYLINDER HEAD........................................................5-20
CHECKING THE TIMING CHAIN GUIDE (INTAKE SIDE).......................5-20
5
CHECKING THE CYLINDER HEAD ........................................................5-20
INSTALLING THE CYLINDER HEAD ......................................................5-21
KICKSTATER .................................................................................................5-44
REMOVING THE KICK SHAFT ASSEMBLY ...........................................5-45
CHECKING THE KICK SHAFT AND RATCHET WHEEL ........................5-45
CHECKING THE KICK GEAR, KICK IDLE GEAR AND RATCHET
WHEEL ....................................................................................................5-45
INSTALLING THE KICK SHAFT ASSEMBLY ..........................................5-45
INSTALLING THE KICK IDLE GEAR .......................................................5-46
CRANKCASE .................................................................................................5-61
DISASSEMBLING THE CRANKCASE.....................................................5-64
REMOVING THE CRANKCASE BEARING .............................................5-64
CHECKING THE TIMING CHAIN, TIMING CHAIN GUIDE,
OIL STRAINER ........................................................................................5-64
CHECKING THE CRANKCASE ...............................................................5-64
INSTALLING THE OIL SEAL....................................................................5-65
ASSEMBLING THE CRANKCASE...........................................................5-65
TRANSMISSION.............................................................................................5-69
REMOVING THE TRANSMISSION..........................................................5-70
CHECKING THE SHIFT FORKS..............................................................5-70
CHECKING THE SHIFT DRUM ASSEMBLY ...........................................5-71
CHECKING THE TRANSMISSION ..........................................................5-71
INSTALLING THE TRANSMISSION ........................................................5-71
ENGINE REMOVAL
EAS1SME194
TIP
This section is intended for those who have basic knowledge and skill concerning the servicing of
Yamaha motorcycles (e.g., Yamaha dealers, service engineers, etc.). Those who have little knowl-
edge and skill concerning servicing are requested not to undertake inspection, adjustment, disas-
sembly, or reassembly only by reference to this manual. It may lead to servicing trouble and
mechanical damage.
ENGINE REMOVAL
EAS1SME195
(8)
LT
9
LT 6 New
(6)
New 6
8 Nm (0.8 m kgf, 5.8 ft Ibf)
T .R
.
3
30 Nm (3.0 m kgf, 22 ft Ibf) 20 Nm (2.0 m kgf, 14 ft Ibf)
T .R
T .R
.
1
12 Nm (1.2 m kgf, 8.7 ft Ibf) New 6 12 Nm (1.2 m kgf, 8.7 ft Ibf)
T .R
.
T .R
.
LT 8
5-1
ENGINE REMOVAL
T .R
.
10 10 Nm (1.0 m kgf, 7.2 ft Ibf)
T .R
.
(8)
LT
9
LT 6 New
(6)
New 6
8 Nm (0.8 m kgf, 5.8 ft Ibf)
T .R
.
3
30 Nm (3.0 m kgf, 22 ft Ibf) 20 Nm (2.0 m kgf, 14 ft Ibf)
T .R
T .R
.
.
1
12 Nm (1.2 m kgf, 8.7 ft Ibf) New 6 12 Nm (1.2 m kgf, 8.7 ft Ibf)
T .R
.
T .R
.
LT 8
5-2
ENGINE REMOVAL
T .R
.
T.R
.
4
8
7
6
New
5
1
LS
LT
T.R
T .R
.
.
5-3
ENGINE REMOVAL
M
12
1 8
New
LS
3
New
9
2 8
10
11
7
New
55 Nm (5.5 m•kgf, 40 ft•Ibf) 6 5
T .R
.
13
4
11
5-4
ENGINE REMOVAL
M
12
1 8
New
LS
3
New
9
2 8
10
11
7
New
55 Nm (5.5 m•kgf, 40 ft•Ibf) 6 5
T .R
.
13
4
11
5-5
ENGINE REMOVAL
1. Remove:
• Rear shock absorber assembly lower bolt
“1”
• Connecting arm bolt (frame side) “2”
• Silencer “3”
TIP
Move the rear shock absorber to the left side of
the chassis, and remove the silencer.
3. Remove:
1 • Drive sprocket “1”
• Drive chain “2”
TIP
Remove the drive sprocket together with the
3
drive chain.
1. Remove:
• Exhaust pipe 2
TIP
Put the Exhaust pipe 2 into the state as shown
by moving this, and then remove it.
5-6
ENGINE REMOVAL
1. Remove:
• Pivot shaft “1”
TIP
1
If the pivot shaft is pulled all the way out, the
swingarm will come loose. If possible, insert a
shaft of similar diameter into the other side of
the swingarm to support it.
1
1. Remove:
• Bolt “1”
• Silencer body “2”
ECA
NOTICE
Do not hit the silencer stay “a” as it may do
damage to the silencer.
TIP
2. Remove: Remove the inner pipe while holding the silenc-
• Engine “1” er in place with a vise etc.
From the right side.
TIP a
• Make sure that the couplers, the hoses, and
the cables are disconnected.
1
• Lift up the engine, and remove this from its
lower part toward the right of the chassis.
2. Remove:
• Rivet “1”
• Silencer cap “2”
5-7
ENGINE REMOVAL
3. Replace: TIP
• Fiber “1” • Apply heat-resistant sealant to the areas “a”
shown, making sure that there are no gaps in
the beads of sealant.
• Take care not to allow the fiber out of place
when installing the silencer body “3”.
3 1 2 3
a
1
4. Install:
• Silencer body “1” 1
• Bolt “2”
Silencer body bolt
8 Nm (0.8 m·kgf, 5.8 ft·lbf)
INSTALLING THE ENGINE
EAS1SME202
T.
LOCTITE®
R.
1. Install:
TIP • Engine “1”
Install the engine from the right side.
Apply heat-resistant sealant to the areas “a”
• Pivot shaft “2”
shown, making sure that there are no gaps in
the beads of sealant. Pivot shaft
85 Nm (8.5 m·kgf, 61 ft·lbf)
T.
R.
2
a • Engine mounting bolt (lower side) “3”
LT
Engine mounting bolt (lower side)
53 Nm (5.3 m·kgf, 38 ft·lbf)
T.
R.
5. Replace:
R.
6. Install: TIP
• Silencer cap “1” Apply molybdenum disulfide grease to the pivot
• Rivet “2” shaft.
5-8
ENGINE REMOVAL
M
8
2
8
7
9
7 3 2. Install:
9 • Lock washer “1” New
5 • Nut (drive sprocket) “2”
4
Nut (drive sprocket)
75 Nm (7.5 m·kgf, 54 ft·lbf)
T.
R.
1 TIP
5 NOTICE
Make sure to tighten to specification; other-
INSTALLING THE BRAKE PEDAL
EAS1SME203
• Clip “5”
TIP
Apply the lithium-soap-based grease on the
bolt, O-rings and brake pedal bracket. 3. Bend the lock washer tab to lock the nut.
4. Install:
2 • Drive sprocket guide
1 5 • Drive sprocket cover “1”
• Bolt (drive sprocket cover) “2”
4 LS
1
2
1. Install:
• Drive sprocket “1”
• Drive chain “2”
TIP
Install the drive sprocket together with the drive
chain.
5-9
ENGINE REMOVAL
MUFFLER • Clamp
1. Install: • Silencer “1”
• Gasket New • Bolt (silencer) “2”
• Exhaust pipe 1 “1” Bolt (silencer)
• Nut (exhaust pipe 1) “2” 30 Nm (3.0 m·kgf, 22 ft·lbf)
T.
R.
Nut (exhaust pipe)
20 Nm (2.0 m·kgf, 14 ft·lbf) 2
T.
R.
TIP
First temporarily tighten all nuts to 13 Nm (1.3
m·kgf, 9.4 ft·lbf). Then retighten them to 20 Nm
(2.0 m·kgf, 14 ft·lbf).
1 2
2
1 TIP
2 Install and temporarily tighten the silencer so
that its joint is positioned as shown with respect
to the exhaust pipe 2.
2mm (0.08in)
2. Install:
• Clamp
• Exhaust pipe 2 “1”
• Bolt (exhaust pipe 2) “2”
1 4. Tighten:
2 • Bolt (exhaust pipe 2)
Bolt (exhaust pipe 2)
20 Nm (2.0 m·kgf, 14 ft·lbf)
T.
R.
• Clamp
TIP
Clamp
Install and temporarily tighten the exhaust pipe 12 Nm (1.2 m·kgf, 8.7 ft·lbf)
2 with its end positioned as shown with respect
T.
R.
5-10
CAMSHAFT
CAMSHAFT
EAS1SME206
T .R
.
3
7
3 6
1 Spark plug 1
5-11
CAMSHAFT
T .R
T .R
.
.
E
5
(4)
6 E
8
5
6 6 Nm (0.6 m kgf, 4.3 ft Ibf)
T .R
.
E M
New
7 4
New
M
3
T .R
.
6 Nm (0.6 m kgf, 4.3 ft Ibf)
T .R
.
1
2
New
10 Nm (1.0 m kgf, 7.2 ft Ibf)
T .R
.
5 Camshaft cap 2
6 Clip 2
7 Intake camshaft 1
8 Exhaust camshaft 1
For installation, reverse the removal proce-
dure.
5-12
CAMSHAFT
1. Remove:
• Timing mark accessing screw “1” 2
• Crankshaft end accessing screw “2”
4. Remove:
• Bolt (camshaft cap) “1”
• Camshaft cap “2”
1 2
• Clip “3”
2. Align: TIP
• Alignment mark • Remove the bolts (camshaft cap) in a criss-
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ cross pattern, working from the outside in.
a. Turn the crankshaft counterclockwise with a • In order to prevent the clip from falling into the
wrench. crankcase, remove the camshaft cap.
b. Align the top dead center (TDC) mark “a” on ECA33DD027
d c
5. Remove:
• Exhaust camshaft “1”
• Intake camshaft “2”
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲ TIP
3. Remove: Attach a wire “3” to the timing chain to prevent
• Timing chain tensioner cap bolt “1” it from falling into the crankcase.
• Timing chain tensioner “2”
• Gaskets
5-13
CAMSHAFT
2 1
3
3. Measure:
CHECKING THE CAMSHAFT
EAS1SME208
• Camshaft runout
1. Check: Out of specification Replace.
• Camshaft lobes
Blue discoloration/pitting/scratches Re- Camshaft runout limit
place the camshaft. 0.030 mm (0.0012 in)
2. Measure:
• Camshaft lobe dimensions “A” and “B”
Out of specification Replace the cam-
shaft.
Camshaft lobe dimensions
Lobe height (Intake)
31.800–31.900 mm (1.2520–
1.2559 in)
Limit
31.700 mm (1.2480 in)
Base circle diameter (Intake)
22.450–22.550 mm (0.8839– 4. Measure:
0.8878 in) • Camshaft-journal-to-camshaft-cap clear-
Limit ance
22.350 mm (0.8799 in) Out of specification Measure the cam-
Lobe height (Exhaust) shaft journal diameter.
33.850–33.950 mm (1.3327–
1.3366 in) Camshaft-journal-to-camshaft-
Limit cap clearance
33.750 mm (1.3287 in) 0.028–0.062 mm (0.0011–0.0024
Base circle diameter (Exhaust) in)
25.211–25.311 mm (0.9926–
0.9965 in) ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
Limit a. Install the camshaft into the cylinder head.
25.111 mm (0.9886 in) b. Position a strip of Plastigauge® “1” onto the
camshaft journal as shown.
5-14
CAMSHAFT
a. 1/4 tooth
b. Correct
1. Timing chain roller
2. Camshaft sprocket
1 CHECKING THE TIMING CHAIN TENSION-
EAS1SME210
ERS
1. Check:
• Timing chain tensioner
Crack/damage Replace.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
5. Measure:
a. While pressing the tensioner rod lightly with
• Camshaft journal diameter “a”
your fingers, use a thin screwdriver “1” to
Out of specification Replace the cam-
wind the tensioner rod up fully clockwise.
shaft.
b. When releasing the screwdriver by pressing
Within specification Replace the cylinder
lightly with your fingers, make sure that the
head and the camshaft caps as a set.
tensioner rod will come out smoothly.
Camshaft journal diameter c. If not, replace the tensioner assembly.
21.959–21.972 mm (0.8645–
0.8650 in)
SHAFT SPROCKET
1. Check:
• Timing chain
Damage/stiffness Replace the timing
chain and camshaft as a set.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
5-15
CAMSHAFT
TEM b
1. Check:
• Decompression system
a
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Check that the decompressor cam “1”
moves smoothly.
b. Check that the decompressor lever pin “2”
projects from the camshaft.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲ 3
d c
INSTALLING THE CAMSHAFTS
EAS1SME212
1. Install:
• Exhaust camshaft “1”
• Intake camshaft “2”
2 1
ECA33DD029
NOTICE
Do not turn the crankshaft during the cam-
shaft installation. Damage or improper
valve timing will result.
d. Install the clips, the camshaft caps and the
bolts (camshaft cap).
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Turn the crankshaft counterclockwise with a Bolt (camshaft cap)
wrench. 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
T.
R.
TIP
TIP
• Apply molybdenum disulfide oil to the cam-
shafts. • Before installing the clips, cover the cylinder
• Apply the engine oil on the decompression head with a clean cloth to prevent the clips
system. from coming off into the cylinder head cavity.
• Apply the engine oil to the threads and con-
b. Align the top dead center (TDC) mark “a” on tact surfaces.
the rotor with the alignment mark “b” on the • Tighten the bolts to the specified torque in two
crankcase cover. or three steps in the proper tightening se-
quence as shown.
ECA33DD030
NOTICE
The bolts (camshaft cap) must be tightened
evenly, or damage to the cylinder head,
camshaft caps, and camshaft will result.
5-16
CAMSHAFT
3 4 8 7
2 6
1 5
4
5
E
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲ ▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
2. Install: 3. Turn:
• Timing chain tensioner • Crankshaft
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ Counterclockwise several turns.
a. While pressing the tensioner rod lightly with 4. Check:
your fingers, use a thin screwdriver to wind • Top dead center (TDC) mark on the rotor
the tensioner rod up fully clockwise. Align with the crankcase alignment mark.
• Camshaft match marks
Align with the cylinder head surface.
Out of alignment Adjust.
5. Install:
• Timing chain guide (top side) “1”
• Cylinder head cover gasket “2”
• Cylinder head cover “3”
• Bolt (cylinder head cover) “4”
Bolt (cylinder head cover)
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
b. With the tensioner rod fully wound and the
T.
R.
90890-85505
R.
4
3
1
2
c. Release the screwdriver, check that the ten-
sioner rod comes out smoothly, and tighten
the gasket “4” and the cap bolt “5”. 6. Install:
• Cylinder head breather hose
Tensioner cap bolt • Spark plug
6 Nm (0.6 m·kgf, 4.3 ft·lbf)
T.
Spark plug
R.
5-17
CYLINDER HEAD
CYLINDER HEAD
EAS1SME213
T .R
.
10 Nm (1.0 m kgf, 7.2 ft Ibf)
T .R
.
3 Cylinder head 1
5-18
CYLINDER HEAD
T .R
.
10 Nm (1.0 m kgf, 7.2 ft Ibf)
T .R
.
T .R
.
5-19
CYLINDER HEAD
1. Remove:
• Intake camshaft
• Exhaust camshaft
Refer to “REMOVING THE CAMSHAFT” on
page 5-13.
2. Remove:
• Cylinder head nuts
• Cylinder head bolts
TIP
2. Check:
• Loosen the bolts in the proper sequence as
• Cylinder head
shown.
Damage/scratches Replace.
• Loosen each bolt 1/2 of a turn at a time. After
fully loosening all the bolts, remove them. TIP
When replacing the cylinder head, replace also
the valve.
Refer to “CHECKING THE VALVE SEATS” on
page 5-25.
• Cylinder head coolant passages
Mineral deposits/rust Eliminate.
3. Measure:
FWD • Cylinder head warpage
Out of specification Resurface the cylin-
x2 x4 der head.
Warpage limit
0.05 mm (0.0020 in)
6 4
1
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Place a straightedge and a thickness gauge
2 across the cylinder head.
3 5 b. Measure the warpage.
c. If the limit is exceeded, resurface the cylin-
der head as follows.
d. Place a 400–600 grit wet sandpaper on a
surface plate, and resurface the cylinder
CHECKING THE TIMING CHAIN GUIDE (IN-
EAS1SME215
1. Eliminate:
• Combustion chamber carbon deposits
TIP
Use a rounded scraper, not a sharp instrument,
in order not to damage or scratch the spark
plug bore threads.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
EAS1SME217
5-20
CYLINDER HEAD
a
FWD
2 4
3
x2 x4
1
1 3
5
2
6
2. Install: 2
4
• Washer “1”
• Cylinder head bolt “2”
• Cylinder head nut “3”
2 2
1
3
3. Tighten:
• Cylinder head bolt “1” – “4”
• Cylinder head nut “5”, “6”
Cylinder head bolt “1” – “4”
33 Nm (3.3 m·kgf, 24 ft·lbf)
T.
5-21
VALVES AND VALVE SPRINGS
1 Valve lifter 4
2 Adjusting pad 4
3 Valve cotter 8
5 Valve spring 4
8 Intake valve 2
9 Exhaust valve 2
For installation, reverse the removal proce-
dure.
5-22
VALVES AND VALVE SPRINGS
REMOVING THE VALVES b. Check that the valves are properly sealed.
EAS1SME219
TIP TIP
Before removing the internal parts of the cylin- Check that there are no kerosene leaks from
der head (e.g., valves, valve springs, valve the valve seat “1”.
seats), make sure that the valves are properly
sealed.
1. Remove:
• Valve lifter “1”
• Adjusting pad “2”
1
TIP a
• Place a cloth in the timing chain space to pre- a
vent adjusting pads from falling into the crank-
case.
• Make a note of the positions of valve lifters
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
and adjusting pads so that they can be rein-
stalled in their original places. 3. Remove:
• Valve cotter “1”
Valve lapper TIP
90890-04101 Remove the valve cotters by compressing the
Valve lapping tool valve spring with the valve spring compressor
YM-A8998 “2” and the valve spring compressor adapter
“3”.
2. Check:
• Valve sealing
4. Remove:
Leakage at the valve seat Check the
• Valve spring retainer “1”
valve face, the valve seat, and the valve seat
• Valve spring “2”
contact width.
• Valve “3”
Refer to “CHECKING THE VALVE SEATS”
• Valve stem seal “4”
on page 5-25.
• Valve spring seat “5”
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Pour a clean solvent “a” into the intake and
exhaust ports.
5-23
VALVES AND VALVE SPRINGS
TIP
Identify the position of each part very carefully
so that it can be reinstalled in its original place.
2 1
5
2. Replace:
• Valve guide
3
TIP
To ease valve guide removal and installation,
CHECKING THE VALVES AND VALVE and to maintain the correct fit, heat the cylinder
EAS1SME220
Valve-stem-to-valve-guide clear-
ance (intake)
0.010–0.037 mm (0.0004–0.0015 1
in)
Limit
0.080 mm (0.0032 in)
Valve-stem-to-valve-guide clear- b. Install the new valve guide with the valve
ance (exhaust) guide installer “2” and the valve guide re-
0.025–0.052 mm (0.0010–0.0020 mover “1”.
in)
Limit Valve guide installation height “a”
0.100 mm (0.0039 in) Intake
10.8–11.2 mm (0.43–0.44 in)
Exhaust
11.2–11.6 mm (0.44–0.46 in)
5-24
VALVES AND VALVE SPRINGS
5. Measure:
• Valve margin thickness “a”
Out of specification Replace the valve.
Valve margin thickness (intake)
1.20 mm (0.0472 in)
Valve margin thickness (exhaust)
0.85 mm (0.0335 in)
TIP
After replacing the valve guide, reface the valve
seat.
Intake
Valve guide remover (ø5)
90890-04097
Valve guide remover (5.0 mm)
YM-04097 6. Measure:
Valve guide installer (ø5) • Valve stem runout
90890-04098 Out of specification Replace the valve.
Valve guide installer (5.0 mm) TIP
YM-04098
Valve guide reamer (ø5) • When installing a new valve, always replace
90890-04099 the valve guide.
Valve guide reamer (5.0 mm) • If the valve is removed or replaced, always re-
YM-04099 place the valve stem seal.
Exhaust
Valve guide remover (ø4.5) Valve stem runout
90890-04116 0.010 mm (0.0004 in)
Valve guide remover (4.5 mm)
YM-04116
Valve guide installer (ø4.5)
90890-04117
Valve guide installer (4.5 mm)
YM-04117
Valve guide reamer (ø4.5)
90890-04118
Valve guide reamer (4.5 mm)
YM-04118
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3. Eliminate:
CHECKING THE VALVE SEATS
EAS1SME221
• Carbon deposits
(from the valve face and valve seat) 1. Eliminate:
4. Check: • Carbon deposits
• Valve face (from the valve face and valve seat)
Pitting/wear Grind the valve face. 2. Check:
• Valve stem end • Valve seat
Mushroom shape or diameter larger than Pitting/wear Replace the cylinder head.
the body of the valve stem Replace the 3. Measure:
valve. • Valve seat contact width “a”
Out of specification Replace the cylinder
head.
5-25
VALVES AND VALVE SPRINGS
4. Lap:
Valve seat contact width (intake) • Valve face
0.90–1.10 mm (0.0354–0.0433 in) • Valve seat
Valve seat contact width (ex- ECA
haust) NOTICE
0.90–1.10 mm (0.0354–0.0433 in) This model uses titanium intake and ex-
haust valves.
Do not use the valves used for lapping the
valve seat. Always replace the valves used
for lapping with new ones.
TIP
• When replacing the cylinder head, replace
also the valves with new ones without them.
• When replacing the valves or the valve
guides, use new valves to lap the valve seats,
and then replace them with new valves.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Apply Mechanic’s blueing dye (Dykem) “b”
a. Apply a coarse lapping compound “a” to the
onto the valve face.
valve face.
ECA
NOTICE
Do not let the lapping compound enter the
gap between the valve stem and the valve
guide.
5-26
VALVES AND VALVE SPRINGS
2. Measure:
• Compressed valve spring force “a”
Out of specification Replace the valve
spring.
5-27
VALVES AND VALVE SPRINGS
TIP
1. Check: • Make sure each valve is installed in its original
• Valve lifter place.
Damage/scratches Replace the valve lift- • Install the valve springs with the larger pitch
ers and cylinder head. “a” facing up.
b. Smaller pitch
1. Clean: 4. Install:
• Valve stem end • Valve cotter “1”
TIP
Install the valve cotters by compressing the
valve spring with the valve spring compressor
“2” and the valve spring compressor adapter
“3”.
5-28
VALVES AND VALVE SPRINGS
6. Lubricate:
• Adjusting pad “1”
• Valve lifter “2”
7. Install:
• Adjusting pad
• Valve lifter
TIP
• Check that the valve lifter turns smoothly
when rotated with your finger.
• Make sure that the valve lifter and the adjust-
ing pad are reinstalled in their original posi-
tions.
5-29
CYLINDER AND PISTON
T .R
.
New
E
7
New 4
6
3 5 E
E
4
New
T .R
.
10 Nm (1.0 m kgf, 7.2 ft Ibf)
LT
1 Cylinder body 1
2 Gaskets 1
3 Dowel pin 2
5 Piston pin 1
6 Piston 1
5-30
CYLINDER AND PISTON
1. Remove:
• Piston pin clip “1”
• Piston pin “2”
• Piston “3”
ECA
NOTICE
Do not use a hammer to drive the piston pin
out.
TIP
• Before removing the piston pin clip, cover the CHECKING THE CYLINDER AND PISTON
EAS1SME227
Bore
77.000–77.010 mm (3.0315–
3.0319 in)
Taper limit
0.050 mm (0.0020 in)
1 Out of round limit
0.050 mm (0.0020 in)
5-31
CYLINDER AND PISTON
1. Measure:
• Piston ring side clearance
Out of specification Replace the piston
and piston rings as a set.
TIP
Before measuring the piston ring side clear-
ance, eliminate any carbon deposits from the
piston ring grooves and piston rings.
b. If out of specification, rebore or replace the
Ring side clearance
cylinder, and replace the piston and the pis- 0.030–0.065 mm (0.0012–0.0026
ton rings as a set. in)
c. Measure the piston outside diameter “a” at Limit
the measuring point (from piston skirt bot- 0.115 mm (0.0045 in)
tom) “b” with the micrometer.
Diameter
76.955–76.970 mm (3.0297–
3.0303 in)
Measuring point (from piston
skirt bottom)
4.0 mm (0.16 in)
b 2. Install:
a • Piston rings
TIP
Level the piston ring into the cylinder with the
piston.
Piston-to-cylinder clearance
0.030–0.055 mm (0.0012–0.0022
in) a. 10 mm (0.39 in)
Limit 3. Measure:
0.15 mm (0.006 in) • Piston ring end gap
f. If out of specification, replace the cylinder, Out of specification Replace the piston
the piston, and the piston rings as a set. ring.
TIP
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
The oil ring expander’s end gap cannot be
measured. If the oil ring rail’s gap is excessive,
replace all three oil rings.
5-32
CYLINDER AND PISTON
Piston ring
Top ring
End gap (installed)
0.15–0.25 mm (0.0059–0.0098 in)
Limit
0.50 mm (0.0197 in)
Oil ring
End gap (installed)
0.10–0.35 mm (0.0039–0.0138 in) b
1. Check:
1. Install:
• Piston pin
• Oil ring expander “1”
Brown or silver discoloration/excessive
• Lower oil ring rail “2”
wear/pitting/scratches/grooves Replace
• Upper oil ring rail “3”
the piston pin and then check the lubrication
• Top ring “4”
system.
2. Measure: TIP
• Piston pin outside diameter “a” Be sure to install the piston ring so that the
Out of specification Replace the piston manufacturer’s marks or numbers face up.
pin.
Piston pin outside diameter
15.991–16.000 mm (0.6296– 4
0.6299 in)
Limit
15.971 mm (0.6288 in)
3. Measure:
• Piston pin bore inside diameter “b”
Out of specification Replace the piston.
Piston pin bore inside diameter 2. Install:
16.002–16.013 mm (0.6300– • Piston “1”
0.6304 in) • Piston pin “2”
Limit • Piston pin clip “3” New
16.043 mm (0.6316 in)
5-33
CYLINDER AND PISTON
TIP 5. Install:
• Apply the engine oil to the piston pin. • Cylinder gasket New
• Install the piston with the F mark “a” on it • Dowel pin
pointing to its intake (front) side. • Cylinder
• Before installing the piston pin clip, cover the Cylinder bolt
crankcase opening with a cloth to prevent the 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
T.
clip from falling into the crankcase.
R.
• Install the piston pin clips, so that the clip ends TIP
are 3 mm (0.12 in) “c” or more from the cutout • While compressing the piston rings with one
in the piston. hand, install the cylinder with the other hand.
• Pass the timing chain and timing chain guide
a 1 (exhaust side) through the timing chain cavity.
3. Lubricate:
• Piston
• Piston rings
• Cylinder
4. Offset:
• Piston ring end gap
a
15
15 15
d c b
a. Top ring
b. Upper oil ring rail
c. Oil ring expander
d. Lower oil ring rail
5-34
CLUTCH
CLUTCH
EAS1SME231
11
5
T .R
.
6 10
4 9
T .R
.
8
7
2
New
T .R
.
(5)
3 New 21
13
1
12
(6)
LT
14
17
16
15
New 20
19
18
3 Gasket 1
4 Clutch spring 5
5 Pressure plate 1
6 Push rod 1 1
7 Circlip 1
8 Washer 1
9 Bearing 1
10 Ball 1
11 Push rod 2 1
5-35
CLUTCH
11
5
T .R
.
6 10
4 9
T .R
.
8
7
2
New
T .R
.
(5)
3 New 21
13
1
12
(6)
LT
14
17
16
15
New 20
19
18
15 Clutch boss 1
16 Thrust washer 1
17 Primary driven gear 1
18 Spacer 1
19 Bearing 1
20 Washer 1
5-36
CLUTCH
T .R
.
4
6 New 7
LT
8
New
New
New
LS
7
New
LS
2 3
New
1
LS
New
LS
5-37
CLUTCH
1. Remove:
• Clutch boss nut “1”
• Lock washer “2”
• Clutch boss “3”
TIP
• Straighten the lock washer tab.
• While holding the clutch boss with the clutch
holder “4”, loosen the clutch boss nut.
90890-04086 1. Check:
Universal clutch holder • Clutch plate
YM-91042 Damage Replace the clutch plates as a
set.
2 1 2. Measure:
• Clutch plate warpage
(with a surface plate and thickness gauge
“1”)
Out of specification Replace the clutch
4 plates as a set.
Warpage limit
3 0.10 mm (0.004 in)
1. Check:
• Friction plate
Damage/wear Replace the friction plates
as a set.
2. Measure:
• Friction plate thickness
Out of specification Replace the friction
plates as a set.
TIP
CHECKING THE CLUTCH SPRINGS
EAS1SME235
5-38
CLUTCH
1. Check:
• Push lever shaft
Wear/damage Replace.
1. Check:
• Clutch housing dogs “a”
Damage/pitting/wear Deburr the clutch
housing dogs or replace the clutch housing. CHECKING THE CLUTCH PUSH RODS
EAS1SME240
TIP 1. Check:
Pitting on the clutch housing dogs will cause er- • Push rod 1 “1”
ratic clutch operation. • Bearing “2”
• Washer “3”
• Push rod 2 “4”
• Ball “5”
Cracks/damage/wear Replace.
1. Check:
• Clutch boss splines
Damage/pitting/wear Replace the clutch 2. Measure:
boss. • Push rod 2 bending limit
TIP Out of specification Replace.
Pitting on the clutch boss splines will cause er- Push rod bending limit
ratic clutch operation. 0.30 mm (0.012 in)
1. Check:
• Primary drive gear
Damage/wear Replace the primary drive
and primary driven gears as a set.
Excessive noise during operation Re-
place the primary drive and primary driven
gears as a set.
2. Check:
• Primary-drive-gear-to-primary-driven-gear
CHECKING THE PRESSURE PLATE
EAS1SME238
free play
1. Check: Free play exists Replace the primary
• Pressure plate drive and primary driven gears as a set.
Crack/damage Replace.
5-39
CLUTCH
T.
R.
place the primary drive and primary driven TIP
gears as a set. • Apply the engine oil on the impeller shaft end.
• Mesh the impeller shaft gear “3” with primary
INSTALLING THE OIL SEAL
EAS1SME243
LS
3
2
1 E
1
COVER
1. Install:
• Dowel pin “1”
• O-rings “2” New
• Collar “3”
• Gasket “4” New
2
TIP
Apply the lithium-soap-based grease on the O-
ring.
1
4 New LS
1 2 New
5-40
CLUTCH
1 1
2
4. Bend the lock washer “1” tab.
2. Install:
• Primary driven gear “1” 1
• Thrust washer “2”
• Clutch boss “3”
TIP
Apply the engine oil on the primary driven gear
inner circumference.
5. Install:
• Friction plate 2 “1”
• Friction plate 1 “2”
• Clutch plate “3”
TIP
• Install the clutch plates and friction plates al-
ternately on the clutch boss, starting with a
friction plate and ending with a friction plate.
• From the clutch boss side, install the friction
plates in order: friction plate 2 (pawl portion
3. Install: “a”: straight type) 1, and friction plate 1 (pawl
• Lock washer “1” New portion “a”: stepped type) 8.
• Clutch boss nut “2” • Apply the engine oil on the friction plates and
Clutch boss nut clutch plates.
100 Nm (10 m·kgf, 72 ft·lbf)
2 1
T.
R.
ECA1DX1020
a
NOTICE
Make sure to tighten to specification; other-
wise, it may damage the other part that is
fastened together.
TIP
• Apply the engine oil to the threads and con-
tact surface of the clutch boss nut. 3
• Use the clutch holding tool “3” to hold the
clutch boss.
5-41
CLUTCH
8. Install:
2
3 • Pressure plate “1”
3
1
2 2
6. Install:
• Bearing “1”
• Washer “2” 9. Install:
• Circlip “3” New • Clutch spring
To push rod 1 “4”. • Clutch spring bolt
TIP Clutch spring bolt
Apply the engine oil on the bearing and washer. 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
T.
R.
TIP
Tighten the bolts in stages and in a crisscross
pattern.
3
1
5
7. Install:
• Push rod 2 “1” 4
• Ball “2” 2
• Push rod 1 “3”
TIP 10.Install:
Apply the engine oil on the push rod 1, 2 and • Gasket “1” New
ball.
5-42
CLUTCH
11.Install:
• Clutch cover “1”
• Clutch cover bolt
Clutch cover bolt
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
T.
R.
TIP
Tighten the bolts in stages and in a crisscross
pattern.
1. Install:
• Kickstarter lever “1”
• Washers
• Bolt (kickstarter lever)
Bolt (kickstarter lever)
33 Nm (3.3 m·kgf, 24 ft·lbf)
T.
R.
TIP
Install so that there is a clearance “a” of 5 mm
(0.2 in) or more between the kickstarter lever
and the frame and that the kickstarter lever
does not contact the right crankcase cover
when it is pulled.
a
1
5-43
KICKSTATER
KICKSTATER
EAS1SME247
3 Spring guide 1
4 Torsion spring 1
5 Ratchet wheel 1
6 Kick gear 1
7 Kick shaft 1
For installation, reverse the removal proce-
dure.
5-44
KICKSTATER
1. Remove: a
• Kick shaft assembly “1”
TIP
Unhook the torsion spring “2” from the hole “a”
in the crankcase.
b
1 3 2
1. Install:
• Kick gear “1”
• Washer “2”
• Circlip “3” New
• Ratchet wheel “4”
• Spring “5”
CHECKING THE KICK SHAFT AND RATCH-
EAS1SME249
• Washer “6”
ET WHEEL • Circlip “7” New
1. Check: (to the kick shaft “8”)
• Ratchet wheel “1” smooth movement TIP
Unsmooth movement Replace. • Apply molybdenum disulfide oil to the inner
• Kick shaft “2” circumferences of the kick gear and ratchet
Wear/damage Replace the kick shaft as- wheel.
sembly. • Align the punch mark “a” on the ratchet wheel
• Spring “3” with the punch mark “b” on the kick shaft.
Broken Replace.
1
2
3
2. Install:
CHECKING THE KICK GEAR, KICK IDLE
EAS1SME250
5-45
KICKSTATER
5. Install:
b • Torsion spring “1”
TIP
Turn the torsion spring clockwise and hook into
a
the proper hole “a” in the crankcase.
2
3. Install:
• Spring guide “1”
TIP
Slide the spring guide into the kick shaft, make
sure the groove “a” in the spring guide fits on
the stopper of the torsion spring.
INSTALLING THE KICK IDLE GEAR
EAS1SME252
1. Install:
• Kick idle gear “1”
• Washer “2”
• Circlip “3” New
TIP
• Apply the engine oil on the kick idle gear inner
circumference.
• Install the kick idle gear with its depressed
side “a” toward you.
4. Install:
• Kick shaft assembly “1”
TIP
• Before installation, apply molybdenum disul-
fide grease to the contacting surfaces of the
kick shaft ratchet wheel guide “2” and the kick
shaft stopper “a”.
• Apply the engine oil on the kick shaft.
• Slide the kick shaft assembly into the crank-
case and make sure the kick shaft stopper “a”
fits into the kick shaft ratchet wheel guide.
5-46
SHIFT SHAFT
SHIFT SHAFT
EAS1SME253
T .R
.
14 3
13 LS
LT
4
5
2
12 Nm (1.2 m kgf, 8.7 ft Ibf)
T .R
.
LT
8
7
E
10 15
11
12
LT
10
6
10 Nm (1.0 m kgf, 7.2 ft Ibf)
T .R
.
1 Shift pedal 1
2 Shift shaft 1
3 Oil seals 1
4 Collars 1
6 Roller 1
7 Shift guide 1
8 Shift lever assembly 1
9 Shift lever 1
10 Pawl 2
11 Pawl pin 2
12 Spring 2
13 Stopper lever 1
5-47
SHIFT SHAFT
T .R
.
14 3
13 LS
LT
4
5
2
12 Nm (1.2 m kgf, 8.7 ft Ibf)
T .R
.
LT
8
7
E
10 15
11
12
LT
10
6
10 Nm (1.0 m kgf, 7.2 ft Ibf)
T .R
.
15 Segment 1
For installation, reverse the removal proce-
dure.
5-48
SHIFT SHAFT
REMOVING THE SHIFT GUIDE AND SHIFT CHECKING THE SHIFT SHAFT
EAS1SME254 EAS1SME256
LEVER ASSEMBLY
1. Check:
• Shift guide “1”
REMOVING THE SEGMENT
EAS1SME255
NOTICE
If the segment gets an impact, the stopper 2 3
lever may be damaged. Take care not to
give an impact to it when removing the bolt. 4
1. Check:
• Stopper lever “1”
Wear/damage Replace.
• Torsion spring “2”
Broken Replace.
1 2
EAS1SME259
5-49
SHIFT SHAFT
INSTALLING THE STOPPER LEVER INSTALLING THE SHIFT GUIDE AND SHIFT
EAS1SME261
LOCTITE®
R.
2
3
LT
4
2. Install:
1. Install: • Shift lever assembly “1”
• Segment “1” (to the shift guide “2”)
• Segment bolt
2
Segment bolt
30 Nm (3.0 m·kgf, 22 ft·lbf) 1
T.
R.
TIP
• Align the notch “a” on the segment with the
pin “b” on the shift cam.
• With the stopper lever pushed down, install
the segment.
3. Install:
ECA
NOTICE
• Shift lever assembly “1”
If the segment gets an impact, the stopper
• Shift guide “2”
lever may be damaged. Take care not to
give an impact to it when tightening the bolt. TIP
• The shift lever assembly is installed at the
same time as the shift guide.
• Apply the engine oil on the segment bolt shaft.
2
1
5-50
SHIFT SHAFT
LOCTITE®
R.
T.
R.
1
TIP
1 Align the punch mark “a” on the shift shaft with
the punch mark “b” in the shift pedal.
b
LT a
1. Install: 1 2
• Roller “1”
• Shift shaft spring “2” (to shift shaft)
• Collar “3” (to shift shaft)
• Shift shaft “4”
TIP
Apply the engine oil on the roller, collar and
shift shaft.
1
E
3
2
E
4
2. Install:
• Oil seal New
5-51
OIL PUMP AND BALANCER GEAR
T.R
.
2
1
LT 3
4
5
5 Nm (0.5 m•kgf, 3.6 ft •Ibf) 7
T .R
.
3 Outer rotor 1
4 Dowel pin 1
5 Inner rotor 1
5-52
OIL PUMP AND BALANCER GEAR
T .R
.
5
New
8
7 LT
12
6
LT
11
T .R
.
LT
13
5-53
OIL PUMP AND BALANCER GEAR
1. Loosen:
• Balancer nut “1”
• Primary drive gear nut “2”
• Balancer weight gear nut “3”
TIP
Place an aluminum plate “a” between the teeth
of the balancer drive gear “4” and balancer
weight gear “5”.
1 1. Check:
• Balancer
Crack/damage Replace.
2
CHECKING THE OIL PUMP
EAS1SME268
1. Check:
5 • Oil pump drive shaft
a
• Oil pump housing
• Oil pump cover
Cracks/damage/wear Replace the defec-
4 a 3 tive part(s).
2. Measure:
• Inner-rotor-to-outer-rotor-tip clearance “a”
• Outer-rotor-to-oil-pump-housing clearance
“b”
• Oil-pump-housing-to-inner-rotor-and-outer-
5 rotor clearance “c”
Out of specification Replace the oil pump.
5-54
OIL PUMP AND BALANCER GEAR
TIP
Inner-rotor-to-outer-rotor-tip
clearance • Apply the engine oil on the oil pump drive
Less than 0.150 mm (0.0059 in) shaft and inner rotor.
Limit • Fit the dowel pin into the groove in the inner
0.23 mm (0.0091 in) rotor.
Outer-rotor-to-oil-pump-housing
clearance
0.13–0.18 mm (0.0051–0.0071 in) 1
2
Limit
3
0.25 mm (0.0098 in)
Oil-pump-housing-to-inner-and-
outer-rotor
clearance
0.06–0.11 mm (0.0024–0.0043 in)
Limit
0.18 mm (0.0071 in)
2. Install:
• Outer rotor “1”
b
TIP
Apply the engine oil on the outer rotor.
1
a
2
E
3 3. Install:
c • Oil pump cover “1”
• Oil pump cover screw “2”
Oil pump cover screw
2.0 Nm (0.20 m·kgf, 1.4 ft·lbf)
T.
R.
1. Inner rotor
2. Outer rotor
2
1
3. Oil pump housing
3. Check:
• Oil pump operation
Rough movement Repeat steps (1) and
(2) or replace the defective part(s).
ASSEMBLING THE OIL PUMP
EAS1SME269
1. Install:
• Oil pump drive shaft “1”
• Inner rotor “2”
• Dowel pin “3”
5-55
OIL PUMP AND BALANCER GEAR
ER GEAR
1. Install: a
• Oil pump assembly “1” b
• Oil pump assembly bolt “2”
Oil pump assembly bolt
5 Nm (0.5 m·kgf, 3.6 ft·lbf)
T.
LOCTITE®
R.
LT
2
1
ECA
NOTICE
After tightening the bolts, make sure that
the oil pump turns smoothly.
1
2. Install:
• Collar “1”
• Balancer weight gear “2”
TIP
Install the balancer weight gear and balancer
shaft with their lower splines “a” aligning with
each other. 2
4. Install:
• Conical washer “1” New
• Balancer weight gear nut “2”
Balancer weight gear nut
1 50 Nm (5.0 m·kgf, 36 ft·lbf)
T.
R.
2
• Primary drive gear “3”
• Conical washer “4” New
• Primary drive gear nut “5”
• Collar “2”
• Balancer “6”
TIP • Conical washer “7” New
• Align the punched mark “a” on the balancer • Balancer nut “8”
drive gear with the punched mark “b” on the
balancer weight gear. Balancer nut
• Install the balancer drive gear and crankshaft 38 Nm (3.8 m·kgf, 27 ft·lbf)
T.
R.
5-56
OIL PUMP AND BALANCER GEAR
TIP
• Apply engine oil to the contact surface and
threaded portion of the primary drive gear nut.
• Place an aluminum plate “a” between the
teeth of the balancer drive gear “9” and bal-
ancer weight gear “10”.
• Install the conical washer with its convex sur-
face “b” outward.
• Align the balancer flat portion “c” with the flat
portion “d”.
• Apply the engine oil to the contact surface and
threaded portion of the balancer nut.
1 10
9 2
b 2
a
9 a
4 5 10
3 b 5
d c
8
7
6 6 b 8
5-57
AC MAGNETO
AC MAGNETO
EAS1SME271
1
10
2
8 Nm (0.8 m•kgf, 5.8 ft •Ibf)
T .R
.
12 Nm (1.2 m•kgf, 8.7 ft•Ibf)
T .R
.
6
T .R
.
LT
8
LT
6
5 New
7
LT
9
10 Nm (1.0 m•kgf, 7.2 ft •Ibf)
T .R
.
T .R
.
5-58
AC MAGNETO
1. Remove: 1. Check:
• Nut (rotor) “1” • Woodruff key “1”
Damage Replace.
• Washers
1
INSTALLING THE AC MAGNETO
EAS1SME275
2. Remove:
• Rotor “1” 1. Install:
Use the rotor puller “2” to remove the rotor. • Stator “1”
• Woodruff key • Screw (stator) “2”
Rotor puller Screw (stator)
90890-04151 8 Nm (0.8 m·kgf, 5.8ft·lbf)
T.
Rotor puller LOCTITE®
YM-04151 R.
LOCTITE®
R.
Holder
8 Nm (0.8 m·kgf, 5.8 ft·lbf)
LOCTITE®
TIP
CHECKING THE AC MAGNETO
EAS1SME273
6
LT 5
2 LT
a
a
1
4
4 3
5-59
AC MAGNETO
2. Install:
1 3
• Woodruff key “1”
• Rotor “2” 5
TIP
• Clean the contact surfaces of the tapered por-
tions of the crankshaft and rotor.
• When installing the woodruff key, make sure 4
that its flat surface “a” is in parallel with the 5
crankshaft center line “b”. 2 5
4
1 5 5
• When installing the rotor, align the keyway “c”
of the rotor with the woodruff key. 5. Connect:
• AC magneto lead
Refer to “CABLE ROUTING DIAGRAM” on
1 page 2-29.
b 1 a
2
3. Install:
• Washers
• Nut (rotor) “1”
Nut (rotor)
65 Nm (6.5 m·kgf, 47 ft·lbf)
T.
R.
1
4. Install:
• Dowel pin “1”
• Gasket (left crankcase cover) “2” New
• Left crankcase cover “3”
• Lead holder “4”
• Bolt (left crankcase cover) “5”
Bolt (left crankcase cover)
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
T.
R.
TIP
Tighten the bolts in stages and in a crisscross
pattern.
5-60
CRANKCASE
CRANKCASE
EAS1SME276
T .R
.
LT
5
12
6
7
4 4
4 10 9 11
3
1
9
6 8
4
12 Nm (1.2 m kgf, 8.7 ft Ibf)
T .R
LT
.
.
.
3 Timing chain 1
7 Right crankcase 1
5-61
CRANKCASE
T .R
.
LT
5
12
6
7
4 4
4 10 9 11
3
1
9
6 8
4
12 Nm (1.2 m kgf, 8.7 ft Ibf)
T .R
LT
.
.
.
9 Dowel pin 2
10 Crankshaft 1
12 Oil nozzle 1
For assembly, reverse the disassemble pro-
cedure.
5-62
CRANKCASE
T .R
.
1
2 New
3
New 2
LT 3
3
3
3
3
LT
3
3
LT
LT
12 Nm (1.2 m kgf, 8.7 ft Ibf)
T .R
.
1 Circlip 2
2 Oil seals 3
3 Bearing 11
For installation, reverse the removal proce-
dure.
5-63
CRANKCASE
1. Separate:
• Right crankcase
• Left crankcase
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the crankcase bolts.
a
1. Remove:
• Bearing “1”
TIP
TIP
• Remove the bearing from the crankcase by
Loosen each bolt 1/4 of a turn at a time and af- pressing its inner race.
ter all the bolts are loosened, remove them. • Do not use the removed bearing.
b. Remove the right crankcase “1”.
TIP
• Place the crankcase with its left side down-
ward and split it by inserting a screwdriver tip
into the splitting slit “a” in the crankcase.
• Lift the right crankcase horizontally while light-
ly patting the crankcase splitting slit and the
engine mounting boss using a soft hammer,
and leave the crankshaft and the transmission
with the left crankcase.
CHECKING THE TIMING CHAIN, TIMING
EAS1SME279
ECA
1. Wash:
• Crankcase
1 TIP
• Wash the crankcase in a mild solvent.
• Remove any remaining gasket from the
crankcase mating surface.
2. Check:
• Crankcase
Crack/damage Replace.
• Oil delivery passages
Obstruction Blow out with compressed
air.
5-64
CRANKCASE
T.
R.
4.5–5.0 mm (0.18–0.20 in)
TIP
• Apply the lithium-soap-based grease on the
1 O-ring.
• Fit the right crankcase onto the left crankcase.
Tap lightly on the case with soft hammer.
• When installing the crankcase, the connecting
rod should be positioned at top dead center
(TDC).
• Tighten the bolts in a crisscross pattern in two
(2) stages, with 1/4 turn each.
a
1. Install: LT 1
• Bearing cover plate screw
Bearing cover plate screw
12 Nm (1.2 m·kgf, 8.7 ft·lbf) 2
LOCTITE®
T.
R.
4 4 4
LOCTITE®
R.
5-65
CRANKSHAFT ASSEMBLY AND BALANCER SHAFT
1
M
1 Balancer shaft 1
2 Crankshaft assembly 1
For installation, reverse the removal proce-
dure.
5-66
CRANKSHAFT ASSEMBLY AND BALANCER SHAFT
1 3. Measure:
• Crank assembly width “a”
Out of specification Replace the crank-
shaft.
Crank assembly width
55.95–56.00 mm (2.203–2.205 in)
1. Measure:
• Crankshaft runout
Out of specification Replace the crank- 4. Check:
shaft, bearing or both. • Crankshaft sprocket “1”
TIP Damage Replace the crankshaft.
Turn the crankshaft slowly.
Runout limit
0.030 mm (0.0012 in)
1
5. Check:
• Crankshaft journal oil passage
Obstruction Blow out with compressed
air.
5-67
CRANKSHAFT ASSEMBLY AND BALANCER SHAFT
BLY
1. Install:
• Crankshaft assembly
TIP
Install the crankshaft assembly with the crank-
shaft installer pot “1”, crankshaft installer bolt
“2”, adapter (M12) “3” and spacer “4”.
90890-01278 NOTICE
Adapter #3 Do not apply the molybdenum grease to the
YU-90063 balancer shaft thread.
Spacer (crankshaft installer)
90890-04081
Pot spacer 1
M
YM-91044
ECA
NOTICE
a
• To avoid scratching the crankshaft and to
ease the installation procedure, lubricate
the oil seal lips with lithium-soap-based
grease.
• In order to prevent the crankshaft seizure,
apply molybdenum disulfide grease.
TIP
Hold the connecting rod at top dead center
(TDC) with one hand while turning the nut of the
crankshaft installer bolt with the other. Turn the
crankshaft installer bolt until the crankshaft as-
sembly bottoms against the bearing.
5-68
TRANSMISSION
TRANSMISSION
EAS1SME288
M
2
New
M
10
M
M 9
8
7
1 M
5
3 E
4
5 E 6
E E
2 Drive axle 1
5 Spring 4
6 Shift cam 1
5-69
TRANSMISSION
1. Remove: 1. Check:
• Long shift fork guide bar “1” • Shift fork cam follower “1”
• Short shift fork guide bar “2” • Shift fork pawl “2”
• Shift cam “3” Bends/damage/scoring/wear Replace the
• Shift fork 3 “4” shift fork.
• Shift fork 2 “5”
• Shift fork 1 “6”
• Main axle “7”
• Drive axle “8”
• Collar “9”
TIP
• Remove assembly with the collar “9” installed
to the crankcase.
• Make a note of the position of each part. Pay
particular attention to the location and direc-
tion of shift forks. 2. Check:
• Remove the main axle and the drive axle all • Shift fork guide bar
together by tapping the drive axle lightly with Roll the shift fork guide bar on a flat surface.
a soft hammer. Bends Replace.
EWA
WARNING
2 Do not attempt to straighten a bent shift fork
guide bar.
1
4 3
6
8 3. Check:
• Shift fork movement
(along the shift fork guide bar)
Rough movement Replace the shift forks
7 and shift fork guide bar as a set.
5-70
TRANSMISSION
1. Check:
• Shift drum groove
Damage/scratches/wear Replace the
shift drum assembly.
• Shift drum segment “1”
Damage/wear Replace the shift drum as-
sembly.
3. Check:
• Transmission gears
Blue discoloration/pitting/wear Replace
the defective gear (s).
• Transmission gear dogs
Cracks/damage/rounded edges Replace
the defective gear (s).
4. Check:
• Transmission gear movement
CHECKING THE TRANSMISSION
EAS1SME292
5
4
3
2. Measure: 2
1
• Drive axle runout
6
(with a centering device and dial gauge “1”)
Out of specification Replace the drive ax-
le.
Drive axle runout limit M
0.08 mm (0.0032 in)
5-71
TRANSMISSION
2. Install:
• 2nd wheel gear (28T) “1”
• 4th wheel gear (22T) “2” c c
• 3rd wheel gear (26T) “3”
• 5th wheel gear (25T) “4”
• Collar “5”
• 1st wheel gear (30T) “6”
• O-rings “7” New
(to the drive axle “8”)
TIP
• Before installation, apply molybdenum disul- 4. Install:
fide oil to the inner and end surface of the idler • Collar “1”
gear and the collar and to the inner surface of TIP
the sliding gear, then install. • Apply the lithium soap base grease on the oil
• Apply the lithium-soap-based grease on the seal lip.
O-ring. • When installing the collar into the crankcase,
pay careful attention to the crankcase oil seal
LS 7 lip.
8
1
2
4 3
65 New
M
M
3. Install:
• Washer “1”
• Circlip “2” New 5. Install:
TIP • Main axle “1”
• Be sure the circlip sharp-edged corner “a” is • Drive axle “2”
positioned opposite side to the washer and TIP
gear “b”. • Install to the left crankcase simultaneously.
• Install the circlip with its ends “c” settled even- • Apply engine oil to the main axle and the drive
ly on the spline crests. axle bearing.
1 b
1
2
2 2
a
5-72
TRANSMISSION
6. Install: 7. Install:
• Shift fork 1 (L) “1” • Long shift fork guide bar “1”
• Shift fork 2 (C) “2” • Short shift fork guide bar “2”
• Shift fork 3 (R) “3” • Spring “3”
• Shift cam “4” TIP
(to the main axle and the drive axle) • Screw the spring into the shift fork guide bar
TIP lightly beforehand.
• Apply engine oil to the shift fork grooves. • Apply the engine oil on the shift fork guide
• Apply engine oil to the shift cam groove and bars.
the bearing contact surface.
• Mesh the shift fork 1 (L) with the 4th wheel 3
gear “5” and 3 (R) with the 5th wheel gear “7”
on the drive axle. E
3 8. Check:
• Operation of shift cam and shift fork
• Transmission operation
2 Unsmooth operation Repair.
1
7
3
E
1
E
2
E 4
5-73
COOLING SYSTEM
RADIATOR .......................................................................................................6-1
HANDLING NOTE ......................................................................................6-3
CHECKING THE RADIATOR .....................................................................6-3
WATER PUMP..................................................................................................6-4
REMOVING THE OIL SEAL .......................................................................6-6
CHECKING THE WATER PUMP ...............................................................6-6
CHECKING THE BEARING .......................................................................6-6
INSTALLING THE OIL SEAL......................................................................6-6
ASSEMBLING THE WATER PUMP...........................................................6-6
6
RADIATOR
EAS1SME294
TIP
This section is intended for those who have basic knowledge and skill concerning the servicing of
Yamaha motorcycles (e.g., Yamaha dealers, service engineers, etc.). Those who have little knowl-
edge and skill concerning servicing are requested not to undertake inspection, adjustment, disas-
sembly, or reassembly only by reference to this manual. It may lead to servicing trouble and
mechanical damage.
RADIATOR
EAS1SME295
12
New
LS
New
11
LS New
6-1
RADIATOR
12
New
LS
New
11
LS New
4 Radiator hose 2 1
5 Radiator hose 3 1
6 Radiator hose 4 1
7 Radiator pipe 2 1
8 Radiator breather hose 1
9 Left radiator 1
10 Radiator hose 1 1
11 Radiator pipe 1 1
6-2
RADIATOR
HANDLING NOTE
EAS1SME296
EWA
WARNING
If coolant seems hot, do not remove the ra-
diator cap.
1. Check:
• Radiator fins “1”
Obstructions Clean.
Apply compressed air to the rear of the radi-
ator.
Damage Repair or replace.
TIP
Correct any flattened fins with a thin, flat-head
screwdriver.
2. Check:
• Radiator hoses
• Radiator pipes
Crack/damage Replace.
6-3
WATER PUMP
WATER PUMP
EAS1SME298
New
6 4
5
New
7
3 10 4
1
11
E
2
2 LS
8
9 New
LS
LS
New
2 Dowel pin 2
3 Gasket 1
4 Washer 2
5 Collar 1
6 Gear 1
7 Pin 1
6-4
WATER PUMP
New
6 4
5
New
7
3 10 4
1
11
E
2
2 LS
8
9 New
LS
LS
New
11 Oil seal 1
For installation, reverse the removal proce-
dure.
6-5
WATER PUMP
TIP 1 New
• Remove the oil seal when the coolant level
changes frequently more than usual, coolant
has discolored, or engine oil has become
milky.
• Do not use the removed oil seal. 1 New
LS
1. Remove:
• Oil seals “1” 2 LS
2. Install:
• Bearing “1”
1
TIP
Install the bearing by pressing its outer race
parallel.
1
1. Check:
• Water pump housing cover
• Impeller shaft
Cracks/damage/wear Replace.
CHECKING THE BEARING
EAS1SME301
1. Check: 1. Install:
• Bearing • Impeller shaft assembly “1”
Rotate the inner race with your finger. • Washer “2”
Rough spot/seizure Replace. • Pin “3”
• Gear “4”
• Collar “5”
• Circlip “6” New
TIP
• Take care so that the oil seal lip is not dam-
aged or the spring does not slip off its posi-
tion.
• When installing the impeller shaft, apply the
lithium-soap-based grease to the oil seal lip,
the bearing, and the impeller shaft.
INSTALLING THE OIL SEAL
EAS1SME302
1. Install: 4 5 2
6
• Oil seals “1” New 2 3
TIP
New
• Apply the lithium-soap-based grease on the
oil seal lip.
• Install the oil seal with its manufacture’s
1
marks or numbers facing the right crankcase
cover “2”. LS
6-6
WATER PUMP
2. Install:
• Dowel pin “1”
• Gasket “2” New
1 1
2 New
3. Install:
• Water pump housing “1”
• Water pump housing bolt “2”
Water pump housing bolt
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
T.
R.
1
2
2
4 3 New
6-7
FUEL SYSTEM
THROTTLE BODY............................................................................................7-5
CHECKING THE INJECTOR......................................................................7-8
CHECKING THE THROTTLE BODY .........................................................7-8
CHECKING THE THROTTLE BODY JOINT ..............................................7-8
ADJUSTING THE THROTTLE POSITION SENSOR .................................7-9
7
FUEL TANK
EAS1SME304
TIP
This section is intended for those who have basic knowledge and skill concerning the servicing of
Yamaha motorcycles (e.g., Yamaha dealers, service engineers, etc.). Those who have little knowl-
edge and skill concerning servicing are requested not to undertake inspection, adjustment, disas-
sembly, or reassembly only by reference to this manual. It may lead to servicing trouble and
mechanical damage.
FUEL TANK
EAS1SME305
3
5
(6)
4 2
(2)
(2) 1
7-1
FUEL TANK
WARNING
Cover the fuel hose connection with a cloth
when disconnecting it. This is because re-
sidual pressure in the fuel hose could cause
fuel to spurt out when the hose is removed. 3. Remove:
• Side cover (left/right)
ECA
NOTICE
• Seat
Make sure that the fuel hose is disconnect- • Air scoop (left/right)
ed by hand. Do not forcefully disconnect the • Fuel tank
hose with tools.
TIP
TIP Do not set the fuel tank down on the installation
• To disconnect the fuel hose from the fuel tank, surface of the fuel pump. Be sure to lean the
remove the fuel hose connector holder “a”, fuel tank against a wall or the like.
and then slide the fuel hose connector cover.
• To remove the fuel hose from the fuel rail, REMOVING THE FUEL PUMP
EAS1SME307
NOTICE
of the connector, and then remove the hose.
Do not drop the fuel pump or give it a strong
• Before removing the hose, place a few cloths
shock.
in the area under where it will be removed.
• To prevent sand, dust, and other foreign ma-
CHECKING THE FUEL PUMP BODY
EAS1SME308
1. Install:
• Fuel pump gasket New
• Fuel pump
a • Fuel pump bracket
Fuel pump bolts
4.0 Nm (0.40 m·kgf, 2.9 ft·lbf)
T.
R.
TIP
• Take care not to damage the installation sur-
2 faces of the fuel tank.
1
• Always use a new fuel pump gasket.
• Install the lip on the fuel pump gasket upward.
• Install the fuel pump as shown in the figure.
• Align the projection “a” on the fuel pump with
the slot “b” in the fuel pump bracket.
• Tighten the fuel pump bolts in the proper tight-
ening sequence as shown.
7-2
FUEL TANK
b a
3. Connect:
3 • Fuel pump coupler
5 4. Install:
1 • Air scoop (left/right)
• Seat
• Side cover (left/right)
Refer to “GENERAL CHASSIS” on page 4-
2 4 1.
CHECKING THE FUEL PRESSURE
EAS1SME311
6
1. Check:
INSTALLING THE FUEL TANK
EAS1SME310
• Fuel pressure
1. Install: ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
• Fuel tank a. Remove the side cover (left/right), the seat
2. Connect: and the air scoop (left/right).
• Fuel hose Refer to “GENERAL CHASSIS” on page 4-
ECA
1.
NOTICE b. Remove the fuel tank bolt and lift the fuel
• Connect the fuel hose securely, and check tank.
that the orientation of the installed fuel c. Disconnect the fuel hose from the fuel
hose holder is correct. pump.
• Take care not to kink or pinch the fuel Refer to “REMOVING THE FUEL TANK” on
hose. page 7-2.
EWA
TIP WARNING
• Insert the fuel hose into the fuel pipe securely Cover the fuel hose connection with a cloth
until you hear a “click”. when disconnecting it. This is because re-
• Slide the fuel hose connector cover “1” at the sidual pressure in the fuel hose could cause
hose end in the direction of the arrow. fuel to spurt out when the hose is removed.
• Install the fuel hose connector holder “a”.
ECA
NOTICE
• Check that the fuel hose and the fuel pump
Make sure that the fuel hose is disconnect-
lead are routed through the guide on the cov-
ed by hand. Do not forcibly disconnect the
er. hose with tools.
d. Connect the pressure gauge “1” and the fuel
pressure adapter “2” to the fuel hose.
1 Pressure gauge
90890-03153
Pressure gauge
YU-03153
Fuel pressure adapter
90890-03186
Fuel pressure adapter
YM-03186
7-3
FUEL TANK
1
TECTOR
1. Check:
• Protector “1”
Wear/damage Replace.
2 TIP
Affix the protector as shown.
A
1
e. Start the engine.
f. Measure the fuel pressure.
Out of specification Replace the fuel
pump.
Fuel line pressure at idling
300.0–390.0 kPa (3.00–3.90 kgf/ 0 mm
cm2, 43.5–56.6 psi) (0 in)
1
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲ B
1
CHECKING THE DAMPER
EAS1SME312
1. Check:
• Damper 1 “1”
• Damper 2 “2”
• Damper 3 “3”
Wear/damage Replace.
TIP 15 mm
1 (0.59 in)
• Affix dampers 1 and 3 with the arrow on each
damper pointing outward. A. Left
• Affix the damper 2 with its projection “a” facing B. Right
the rear of the vehicle.
1 84 mm 115 mm 3
(3.31 in) (4.53 in)
a
2
84 mm 115 mm
1 (3.31 in) (4.53 in) 3
7-4
THROTTLE BODY
THROTTLE BODY
EAS1SME314
5
3
7 1 9
10
6
8 11
7 Throttle cable 2
8 Fuel hose 1
7-5
THROTTLE BODY
5
3
7 1 9
10
6
8 11
10 Throttle body 1
7-6
THROTTLE BODY
T.R
.
(2)
T .R
. 5 Nm (0.5 m kgf, 3.6 ft lbf)
2
5
(2)
3
2 Injector 1
3 Gaskets 1
7-7
THROTTLE BODY
1. Check:
• Injectors
Obstruction Replace, and check the fuel
pump and the fuel injection system.
Refer to “FUEL INJECTION SYSTEM” on
page 8-10.
Deposits Replace.
Damage Replace.
2. Check: 3
• Injector resistance
Refer to “CHECKING THE FUEL INJEC- b
a
TOR” on page 8-49.
CHECKING THE THROTTLE BODY
EAS1SME316
1. Check:
• Throttle body
Cracks/damage Replace.
2. Check:
• Fuel passages
Obstructions Clean. 3. Check:
ECA
1
2
7-8
THROTTLE BODY
SENSOR
EWA
WARNING
• Handle the throttle position sensor with
special care.
• Never subject the throttle position sensor
to strong shocks. If the throttle position
sensor is dropped, replace it.
1. Check:
• Throttle position sensor
Refer to “CHECKING THE THROTTLE PO-
SITION SENSOR” on page 8-46.
2. Adjust:
• Throttle position sensor angle
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Connect the Yamaha diagnostic tool.
Refer to “YAMAHA DIAGNOSTIC TOOL” on
page 8-12.
Yamaha diagnostic tool
90890-03231
Yamaha diagnostic tool (US)
90890-03234
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
7-9
ELECTRICAL SYSTEM
IGNITION SYSTEM...........................................................................................8-2
CIRCUIT DIAGRAM ...................................................................................8-2
TROUBLESHOOTING................................................................................8-4
ELECTRICAL COMPONENTS.......................................................................8-38
CHECKING THE SWITCHES...................................................................8-40
CHECKING THE IGNITION SPARK GAP................................................8-43
CHECKING THE SPARK PLUG CAP ......................................................8-43
CHECKING THE IGNITION COIL ............................................................8-43
CHECKING THE CRANKSHAFT POSITION SENSOR...........................8-44
CHECKING THE ECU ..............................................................................8-45
CHECKING THE STATOR COIL..............................................................8-45
CHECKING THE RECTIFIER/REGULATOR ...........................................8-45
CHECKING THE COOLANT TEMPERATURE SENSOR ........................8-46
CHECKING THE THROTTLE POSITION SENSOR ................................8-46
CHECKING THE THROTTLE POSITION SENSOR INPUT
VOLTAGE ................................................................................................8-47
CHECKING THE INTAKE AIR PRESSURE SENSOR.............................8-48
CHECKING THE INTAKE AIR TEMPERATURE SENSOR .....................8-48
8
CHECKING THE NEUTRAL SWITCH......................................................8-48
CHECKING THE FUEL INJECTOR .........................................................8-49
EAS1SME319
TIP
This section is intended for those who have basic knowledge and skill concerning the servicing of
Yamaha motorcycles (e.g., Yamaha dealers, service engineers, etc.). Those who have little knowl-
edge and skill concerning servicing are requested not to undertake inspection, adjustment, disas-
sembly, or reassembly only by reference to this manual. It may lead to servicing trouble and
mechanical damage.
8-1
EAS1SME321
EAS1SME320
L L L R R R R R R R
B B B B B B/L B/L B/L B/L B/L B/L
O R
R O
B/L Gy B/L Gy
IGNITION SYSTEM
R R R
Gy B R B
Gy
O O O
B R B/W Lg R
W W R
R R
W W Lg Lg O
R R B
W W B/W
B R
W W W W
W W
B R R/B
R/B R/B R
B/W
B/Y
B/Y
B B B/R B/R R
B/Y B
ON
OFF
B/R R
8-2
B B
Br/W B/L
G/W B/L
L
L Y B/L
B/Y P P P
P Y Y
Sb Sb Sb
Y/W B/L
L/W Y/W Y/B
B/R
P/B
Y/B
Y/W P
Sb
B/L
L
P Y/B B/L
Sb P/B
B/L P/B L
8-3
IGNITION SYSTEM
TROUBLESHOOTING
EAS1SME322
8-4
IGNITION SYSTEM
8-5
EAS27200
L L L R R R R R R R EAS1SME323
B B B B B B/L B/L B/L B/L B/L B/L
O R
R O
B/L Gy B/L Gy
R R R
Gy B R B
Gy
O O O
CHARGING SYSTEM
B R B/W Lg R
W W R
R R
W W Lg Lg O
R R B
W W B/W
B R
W W W W
W W
B R R/B
R/B R/B R
B/W
B/Y
B/Y
B B B/R B/R R
B/Y B
ON
OFF
B/R R
8-6
B B
Br/W B/L
G/W B/L
L
L Y B/L
B/Y P P P
P Y Y
Sb Sb Sb
Y/W B/L
L/W Y/W Y/B
B/R
P/B
Y/B
Y/W P
Sb
B/L
L
P Y/B B/L
Sb P/B
B/L P/B L
2. AC magneto
3. Rectifier/regulator
4. Joint connector
5. Condenser
8-7
CHARGING SYSTEM
TROUBLESHOOTING
EAS1SME324
8-8
CHARGING SYSTEM
8-9
EAS1SME326
EAS1SME325
L L L R R R R R R R
B B B B B B/L B/L B/L B/L B/L B/L
O R
R O
B/L Gy B/L Gy
R R R
Gy B R B
Gy
O O O
B R B/W Lg R
W W R
R R
W W Lg Lg O
R R B
W W B/W
B R
W W W W
FUEL INJECTION SYSTEM
W W
B R R/B
R/B R/B R
B/W
B/Y
B/Y
B B B/R B/R R
B/Y B
ON
OFF
B/R R
8-10
B B
Br/W B/L
G/W B/L
L
L Y B/L
B/Y P P P
P Y Y
Sb Sb Sb
Y/W B/L
L/W Y/W Y/B
B/R
P/B
Y/B
Y/W P
Sb
B/L
L
P Y/B B/L
Sb P/B
B/L P/B L
8-11
FUEL INJECTION SYSTEM
8-12
FUEL INJECTION SYSTEM
6
2 3 4 5
2
1. Vehicle
2. Coupler for connecting optional part
3. FI diagnostic tool sub-lead
4. Sub-harness (included with the Yamaha di-
agnostic tool)
5. Vehicle communication cable (included with
the Yamaha diagnostic tool)
6. Yamaha diagnostic tool
7. Battery (12 V)
8-13
FUEL INJECTION SYSTEM
1. Recovered
The item list of the malfunction detected in the past (already recovered) are displayed.
2. Detected
The item list of the malfunction currently occurred are displayed.
3. Code
The following icons and the fault code numbers for the detected malfunctions are displayed.
A B
A. Detected malfunction
B. Recovered malfunction
8-14
FUEL INJECTION SYSTEM
4. ECU
The types of the control units are displayed.
5. Item
The item names of the detected malfunction are displayed.
6. Condition
The current conditions are displayed. (Detected/Recovered)
7. Symptom
The symptoms of the detected malfunction are displayed.
8. Diagnosis code
The diagnosis codes related to the detected malfunction are displayed.
9. FFD (only for models that can display freeze frame data)
The mark “ ” is displayed when the freeze frame data is available.
10.ECU conduction time (hour: minute: second)
The total ECU conduction time (total hours the vehicle’s start switch was ON) when the malfunc-
tion was detected is displayed.
11.Number of main switch operation after detection
The number of times the main switch was turned on between the malfunction detection and code
reading is displayed.
12.Number of occurrences
The number of malfunction occurrences between the malfunction detection and code reading is
displayed.
TROUBLESHOOTING DETAILS
EAS1SME328
This section describes the measures per fault code number displayed on the diagnostic tool. Check
and service the items or components that are the probable cause of the malfunction following the or-
der given.
After the check and service of the malfunctioning part have been completed, reset the diagnostic tool
display according to the reinstatement method.
Fault code No.:
Fault code number displayed on the diagnostic tool when the engine failed to work normally.
Diagnostic code No.:
Diagnostic code number to be used when the diagnostic mode is operated.
8-15
FUEL INJECTION SYSTEM
8-16
FUEL INJECTION SYSTEM
TIP
If fault code numbers 13 and 14 are both displayed, perform checkup and repair jobs for fault code
number 13 first.
8-17
FUEL INJECTION SYSTEM
TIP
If fault code numbers 13 and 14 are both displayed, perform checkup and repair jobs for fault code
number 13 first.
8-18
FUEL INJECTION SYSTEM
8-19
FUEL INJECTION SYSTEM
8-20
FUEL INJECTION SYSTEM
8-21
FUEL INJECTION SYSTEM
TIP
Make sure that the machine is completely cold before checking the coolant temperature sensor.
8-22
FUEL INJECTION SYSTEM
TIP
Make sure that the machine is completely cold before checking the intake air temperature sensor.
8-23
FUEL INJECTION SYSTEM
8-24
FUEL INJECTION SYSTEM
8-25
FUEL INJECTION SYSTEM
TIP
Disconnect the fuel pump coupler when this diagnostic tool is used.
8-26
FUEL INJECTION SYSTEM
8-27
FUEL INJECTION SYSTEM
8-28
FUEL INJECTION SYSTEM
8-29
FUEL INJECTION SYSTEM
8-30
FUEL INJECTION SYSTEM
8-31
FUEL INJECTION SYSTEM
8-32
FUEL INJECTION SYSTEM
8-33
EAS1SME330
EAS1SME329
L L L R R R R R R R
B B B B B B/L B/L B/L B/L B/L B/L
O R
R O
B/L Gy B/L Gy
R R R
Gy B R B
Gy
O O O
B R B/W Lg R
FUEL PUMP SYSTEM
W W R
R R
W W Lg Lg O
R R B
W W B/W
B R
W W W W
W W
B R R/B
R/B R/B R
B/W
B/Y
B/Y
B B B/R B/R R
B/Y B
ON
OFF
B/R R
8-34
B B
Br/W B/L
G/W B/L
L
L Y B/L
B/Y P P P
P Y Y
Sb Sb Sb
Y/W B/L
L/W Y/W Y/B
B/R
P/B
Y/B
Y/W P
Sb
B/L
L
P Y/B B/L
Sb P/B
B/L P/B L
2. AC magneto
3. Rectifier/regulator
4. Joint connector
5. Condenser
7. Engine stop switch
9. ECU (electronic control unit)
13.Fuel pump
8-35
FUEL PUMP SYSTEM
TROUBLESHOOTING
EAS1SME331
8-36
FUEL PUMP SYSTEM
EAS1SME332
8-37
ELECTRICAL COMPONENTS
ELECTRICAL COMPONENTS
EAS1SME333
4
7
10
8-38
ELECTRICAL COMPONENTS
1. Rectifier/regulator
2. Intake air pressure sensor
3. Throttle position sensor
4. Injector
5. Intake air temperature sensor
6. ECU (electronic control unit)
7. Ignition coil
8. Condenser
9. Neutral switch
10.Coolant temperature sensor
8-39
ELECTRICAL COMPONENTS
2
P Sb Y/W
Y/W P
Sb
8-40
ELECTRICAL COMPONENTS
8-41
ELECTRICAL COMPONENTS
Check each switch for continuity with the pocket tester. If the continuity reading is incorrect, check
the wiring connections and if necessary, replace the switch.
ECA14370
NOTICE
Never insert the tester probes into the coupler terminal slots “1”. Always insert the probes
from the opposite end of the coupler, taking care not to loosen or damage the leads.
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
TIP
• Before checking for continuity, set the pocket tester range to “ 1” to make a “0” adjustment.
• When checking for continuity, switch back and forth between the switch positions a few times.
Terminal connections of the switch are shown in the terminal connection diagram below.
The switch positions “a” are shown in the far left column and the switch lead colors are shown in the
top row in the switch illustration.
TIP
“ ” indicates continuity between switch terminals (i.e., a closed circuit at each switch posi-
tion).
The example illustration below shows that:
There is continuity between red and brown when the switch is “ON”.
8-42
ELECTRICAL COMPONENTS
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
1. Check: a. Connect the pocket tester ( 1k) to the
• Ignition spark gap spark plug cap.
Out of specification Perform the ignition
Pocket tester
system troubleshooting. 90890-03112
Refer to “TROUBLESHOOTING” on page 8- Analog pocket tester
4. YU-03112-C
Minimum ignition spark gap
6.0 mm (0.24 in)
TIP
If the ignition spark gap is within specification,
the ignition system circuit is operating normally.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the spark plug cap from the spark
plug.
b. Connect the ignition checker “1”.
b. Measure the spark plug cap resistance.
Ignition checker
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
90890-06754
Oppama pet-4000 spark checker CHECKING THE IGNITION COIL
EAS1SME337
YM-34487 1. Disconnect:
• Ignition coil terminal
c. Crank the engine, and measure the ignition
(from the sub wire harness)
spark gap “a”.
• Spark plug cap
(from the ignition coil)
2. Check:
• Primary coil resistance
Out of specification Replace.
Primary coil resistance
2.16–2.64
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Connect the pocket tester ( 1) to the igni-
2. Spark plug cap tion coil.
d. Crank the engine, and gradually increase Pocket tester
the spark gap until a misfire occurs. 90890-03112
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
Analog pocket tester
YU-03112-C
CHECKING THE SPARK PLUG CAP
EAS1SME336
8-43
ELECTRICAL COMPONENTS
SENSOR
1. Disconnect:
• Crankshaft position sensor coupler
(from the wire harness)
2. Check:
• Crankshaft position sensor resistance
Out of specification Replace.
Crankshaft position sensor resis-
tance
b. Measure the primary coil resistance.
228–342
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
3. Check: ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
• Secondary coil resistance a. Connect the pocket tester ( 100) to the
Out of specification Replace. crankshaft position sensor coupler.
Secondary coil resistance Pocket tester
8.64–12.96 k 90890-03112
Analog pocket tester
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ YU-03112-C
a. Connect the pocket tester ( 1k) to the ig-
nition coil. • Positive tester probe
Pocket tester Gray “1”
90890-03112 • Negative tester probe
Analog pocket tester Black “2”
YU-03112-C
8-44
ELECTRICAL COMPONENTS
1. Check: 1. Check:
• Mounted condition of ECU. • Rectifier/regulator output voltage
Improperly mounted Remount. Out of specification Replace.
TIP Regulated voltage (DC)
• The lean angle sensor is built into the ECU. 14.1–14.9 V
• The lean angle sensor stops the engine in
case of a turnover. ▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
• To ensure that the lean angle sensor operates a. Set the digital tachometer to the ignition coil.
correctly, do not change the installed condi-
Digital tachometer
tion of the ECU.
90890-06760
Digital tachometer
CHECKING THE STATOR COIL
EAS1SME340
YU-39951-B
1. Disconnect:
• Stator coil coupler b. Connect the pocket tester (20 VDC) to the
(from the wire harness) rectifier/regulator coupler.
2. Check:
• Stator coil resistance Pocket tester
90890-03112
Out of specification Replace.
Analog pocket tester
Stator coil resistance YU-03112-C
0.624–0.936
• Positive tester probe
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼ Red “1”
a. Connect the pocket tester ( 1) to the sta- • Negative tester probe
tor coil coupler. Black “2”
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
8-45
ELECTRICAL COMPONENTS
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Connect the pocket tester ( 1k/100) to
the coolant temperature sensor.
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C
WARNING
• Handle the throttle position sensor with
special care.
G/W B/L
• Never subject the throttle position sensor
to strong shocks. If the throttle position
1 2 sensor is dropped, replace it.
8-46
ELECTRICAL COMPONENTS
8-47
ELECTRICAL COMPONENTS
P/B
1 2
P/B
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
2 1
1. Remove:
b. Start the engine.
• Neutral switch
c. Measure the intake air pressure sensor out-
2. Check:
put voltage.
• Neutral switch
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
Out of specification Replace.
CHECKING THE INTAKE AIR TEMPERA-
EAS1SME346
Pocket tester
TURE SENSOR 90890-03112
1. Remove: Analog pocket tester
• Intake air temperature sensor YU-03112-C
(from the air filter case)
EWA
WARNING
• Handle the intake air temperature sensor
with special care.
• Never subject the intake air temperature
sensor to strong shocks. If the intake air
temperature sensor is dropped, replace it.
8-48
ELECTRICAL COMPONENTS
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
Continuity
Positive tester probe a. Disconnect the fuel injector coupler from the
Sky blue “1” fuel injector.
Negative tester probe b. Connect the pocket tester ( 10) to the
Sensor terminal “a” fuel injector coupler.
Continuity
Pocket tester
Positive tester probe
90890-03112
Pink “2”
Analog pocket tester
Negative tester probe
YU-03112-C
Sensor terminal “b”
Continuity
Positive tester probe • Positive tester probe
Pink “2” Injector terminal “1”
Negative tester probe • Negative tester probe
Sensor terminal “c” Injector terminal “2”
Continuity
Positive tester probe
Yellow/white “3”
Negative tester probe 1 2
Sensor terminal “d”
Continuity
Positive tester probe
Yellow/white “3”
Negative tester probe
Sensor terminal “e”
Continuity
Positive tester probe c. Measure the fuel injector resistance.
Yellow/white “3”
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
Negative tester probe
Sensor terminal “f”
f e 3 2
Y/W P
Sb
d
1
b a c
1. Remove:
• Fuel injector
Refer to “THROTTLE BODY” on page 7-5.
2. Check:
• Fuel injector resistance
Out of specification Replace.
Resistance
12
8-49
ELECTRICAL COMPONENTS
8-50
TROUBLESHOOTING
TROUBLESHOOTING......................................................................................9-1
GENERAL INFORMATION ........................................................................9-1
STARTING FAILURES ...............................................................................9-1
INCORRECT ENGINE IDLING SPEED .....................................................9-1
POOR MEDIUM-AND-HIGH-SPEED PERFORMANCE ............................9-2
SHIFTING IS DIFFICULT ...........................................................................9-2
SHIFT PEDAL DOES NOT MOVE .............................................................9-2
JUMPS OUT OF GEAR..............................................................................9-2
CLUTCH SLIPS ..........................................................................................9-2
CLUTCH DRAGS .......................................................................................9-2
OVERHEATING..........................................................................................9-2
OVERCOOLING .........................................................................................9-3
POOR BRAKING PERFORMANCE ...........................................................9-3
FRONT FORK OIL LEAKING .....................................................................9-3
FAULTY FRONT FORK LEGS ...................................................................9-3
UNSTABLE HANDLING .............................................................................9-3
9
TROUBLESHOOTING
1. Spark plug
GENERAL INFORMATION • Incorrect spark plug gap
EAS1SME350
• Faulty ECU
• Faulty crankshaft position sensor
Engine
• Broken generator rotor woodruff key
1. Cylinder and cylinder head
4. Switches and wiring
• Loose spark plug
• Faulty ECU
• Loose cylinder head or cylinder
• Faulty engine stop switch
• Damaged cylinder head gasket
• Broken or shorted wiring
• Damaged cylinder gasket
• Faulty neutral switch
• Worn or damaged cylinder
• Improperly grounded circuit
• Incorrect valve clearance
• Loose connections
• Improperly sealed valve
• Incorrect valve-to-valve-seat contact INCORRECT ENGINE IDLING SPEED
EAS1SME352
9-1
TROUBLESHOOTING
• Faulty ECU
• Faulty crankshaft position sensor Engine
• Broken generator rotor woodruff key 1. Clutch
• Improperly assembled clutch
POOR MEDIUM-AND-HIGH-SPEED PER-
EAS1SME353
1. Fuel pump
• Faulty fuel pump Engine
2. Throttle body 1. Clutch
• Defective throttle body • Unevenly tensioned clutch springs
3. ECU • Warped pressure plate
• Faulty ECU • Bent clutch plate
• Swollen friction plate
SHIFTING IS DIFFICULT
EAS1SME354
2. Engine oil
Engine • Incorrect oil level
1. Shift shaft • Incorrect oil viscosity (high)
• Bent shift shaft • Deteriorated oil
2. Shift drum and shift forks
OVERHEATING
EAS1SME359
9-2
TROUBLESHOOTING
1. Throttle body
• Damaged or loose throttle body joint Chassis
2. Air filter 1. Front fork
• Clogged air filter element • Bent or damaged inner tube
• Bent or damaged outer tube
Chassis • Broken fork spring
1. Brake(s) • Bent or damaged damper rod
• Dragging brake • Incorrect oil viscosity
• Incorrect oil level
Electrical system
UNSTABLE HANDLING
EAS1SME364
1. Spark plug
• Incorrect spark plug gap
• Incorrect spark plug heat range Chassis
2. Ignition system 1. Handlebar
• Faulty ECU • Bent or improperly installed handlebar
• Faulty coolant temperature sensor 2. Steering head components
• Improperly installed upper bracket
OVERCOOLING
EAS1SME360
9-3
LIST OF SELF-DIAGNOSTIC AND FAIL-SAFE ACTIONS
9-4
LIST OF SELF-DIAGNOSTIC AND FAIL-SAFE ACTIONS
9-5
LIST OF SELF-DIAGNOSTIC AND FAIL-SAFE ACTIONS
Diag-
nostic
Item Display Procedure
code
No.
64 Setting history display Displays the presence or ab- —
sence of the setting history by
Power Tuner.
• There is no history. • 00
• There is some history. • 01
• History is unknown (Histo- • 02
ry data is damaged).
65 Setting map erasure Displays the presence or ab- Erase all setting maps by
sence of the setting history by the operation start process-
Power Tuner. ing.
• There is no setting. • 00
• There is some setting. • 01
70 Program version number Displays a program version —
No.
*1: Symbols used in the explanations of the malfunction history
: Normal
: There is currently a malfunction or abnormal condition.
: A malfunction or abnormal condition occurred previously, but the affected system or component
is currently operating normally.
9-6
LIST OF SELF-DIAGNOSTIC AND FAIL-SAFE ACTIONS
9-7
TUNING
CHASSIS ........................................................................................................10-1
SELECTION OF THE SECONDARY REDUCTION RATIO
(SPROCKET)...........................................................................................10-1
DRIVE AND REAR WHEEL SPROCKETS SETTING PARTS.................10-1
TIRE PRESSURE.....................................................................................10-2
FRONT FORK SETTING..........................................................................10-2
CHANGE IN AMOUNT AND CHARACTERISTICS OF FORK OIL ..........10-2
SETTING OF SPRING AFTER REPLACEMENT.....................................10-3
FRONT FORK SETTING PARTS.............................................................10-3
REAR SUSPENSION SETTING...............................................................10-3
CHOOSING SET LENGTH.......................................................................10-3
SETTING OF SPRING AFTER REPLACEMENT.....................................10-4
REAR SHOCK ABSORBER SETTING PARTS .......................................10-5
SUSPENSION SETTING (FRONT FORK)...............................................10-6
SUSPENSION SETTING (REAR SHOCK ABSORBER) .........................10-7
10
CHASSIS
SETTING PARTS
SELECTION OF THE SECONDARY REDUC-
EAS1SME368
10-1
CHASSIS
TIRE PRESSURE
EAS1SME370 EWA1DX4001
WARNING
Tire pressure should be adjusted to suit the Adjust the oil amount in 5 cm3 (0.2 US oz,
road surface condition of the circuit. 0.2 Imp.oz) increments or decrements. Too
Standard tire pressure small oil amount causes the front fork to
100 kPa (1.00 kgf/cm2,15 psi) produce a noise at full rebound or the rider
to feel some pressure on his hands or body.
• Under a rainy, a muddy, a sandy, or a slippery Alternatively, too large oil amount will
condition, the tire pressure should be lower cause the air spring characteristics to have
for a larger area of contact with the road sur- a tendency to be stiffer with the consequent
face. deteriorated performance and characteris-
tics. Therefore, adjust the front fork within
Extent of adjustment
60–80 kPa (0.60–0.80 kgf/cm2, the specified range.
9–12 psi)
Standard oil amount
• Under a stony or a hard road condition, the 335 cm3 (11.33 US oz, 11.82
tire pressure should be higher to prevent a flat lmp.oz) (USA) (CAN) (JPN)
tire. (AUS) (NZL) (ZAF)
340 cm3 (11.50 US oz, 12.00
Extent of adjustment lmp.oz) (EUR)
100–120 kPa (1.00–1.20 kgf/cm2, Extent of adjustment
15–18 psi) 300–365 cm3 (10.14–12.34 US
oz, 10.58–12.87 Imp.oz)
FRONT FORK SETTING
EAS1SME371
10-2
CHASSIS
a
MENT
As the front fork setting can be easily affected
by the rear suspension, take care so that the
front and the rear are balanced (in position etc.)
when setting the front fork.
1. Use of soft spring
• Change the rebound damping force.
Turn out one or two clicks.
• Change the compression damping force.
Turn in one or two clicks.
TIP
Generally a soft spring gives a soft riding feel-
ing. Rebound damping tends to become stron-
ger and the front fork may sink deeply over a
series of gaps.
2. Use of stiff spring
• Change the rebound damping force. 1
Turn in one or two clicks.
• Change the compression damping force.
Turn out one or two clicks. REAR SUSPENSION SETTING
EAS1SME375
TIP
The I.D. mark (slits) “a” is proved on the end of
the spring.
10-3
CHASSIS
2. Remove the stand or block from the engine SETTING OF SPRING AFTER REPLACE-
EAS1SME377
10-4
CHASSIS
PARTS
• Rear shock spring “1”
Spring
I.D.
Type rate N/ Part number
Mark
mm
1SL-22212-40
(Blue)
SOFT 52 Yellow
1SL-22212-50
(Red)
1SL-22212-60
(Blue)
STD 54 Pink
1SL-22212-70
(Red)
1SL-22212-20
(Blue)
56 White
1SL-22212-30
(Red)
1SL-22212-00
(Blue) • Spring preload adjusting positions
STIFF 58 Silver
1SL-22212-10 Spring preload adjusting positions
(Red) Minimum
1SL-22212-80 Position in which the spring is
(Blue) turned in 1.5 mm (0.06 in) from
60 Brown its free length.
1SL-22212-90 Standard
(Red) Position in which the spring is
turned in 10.5 mm (0.41 in) from
TIP its free length. (USA) (CAN)
• The I.D. mark “a” is marked at the end of the (JPN) (AUS) (NZL) (ZAF)
spring. Position in which the spring is
• Spring specification varies according to the turned in 12 mm (0.47 in) from its
color of I.D. marks. free length. (EUR)
Maximum
Position in which the spring is
turned in 18 mm (0.71 in) from its
free length.
TIP
For the spring preload adjustment, refer to “AD-
JUSTING THE REAR SHOCK ABSORBER
ASSEMBLY” on page 3-31.
10-5
CHASSIS
TIP
• If any of the following symptoms is experienced with the standard position as the base, make reset-
ting by reference to the adjustment procedure given in the same chart.
• Before any change, set the rear shock absorber sunken length to the standard figure 90–100 mm
(3.5–3.9 in).
Section
Symptom Medi- Check Adjust
Large Small
Jump um
gap gap
gap
Compression Turn adjuster counterclock-
damping force wise (about 2 clicks) to de-
crease damping.
Stiff over entire
Oil amount Decrease oil amount by about
range
5–10 cm3 (0.2–0.3 US oz, 0.2–
0.4 Imp.oz).
Spring Replace with soft spring.
Outer tube Check for any bends, dents,
Inner tube other noticeable scars, etc. If
any, replace affected parts.
Slide metal Replace with a new one for ex-
Unsmooth tended use.
movement over
entire range Piston metal Replace with a new one for ex-
tended use.
Lower bracket Retighten to specified torque.
tightening
torque
Rebound Turn adjuster counterclock-
Poor initial damping force wise (about 2 clicks) to de-
movement crease damping.
Oil seals Apply grease in oil seal wall.
Compression Turn adjuster clockwise (about
damping force 2 clicks) to increase damping.
Soft over entire
Oil amount Increase oil amount by about
range, bottom-
5–10 cm3 (0.2–0.3 US oz, 0.2–
ing out
0.4 Imp.oz).
Spring Replace with stiff spring.
Stiff toward Decrease oil amount by about
Oil amount
stroke end 5 cm3 (0.2 US oz, 0.2 Imp.oz).
Soft toward Increase oil amount by about 5
stroke end, bot- Oil amount cm3 (0.2 US oz, 0.2 Imp.oz).
toming out
Stiff initial Turn adjuster counterclock-
Compression
movement wise (about 2 clicks) to de-
damping force
crease damping.
10-6
CHASSIS
Section
Symptom Medi- Check Adjust
Large Small
Jump um
gap gap
gap
Compression Turn adjuster clockwise (about
damping force 2 clicks) to increase damping.
Rebound Turn adjuster counterclock-
damping force wise (about 2 clicks) to de-
Low front, tend- crease damping.
ing to lower Balance with Set sunken length for 95–100
front posture rear end mm (3.7–3.9 in) when one
passenger is astride seat (low-
er rear posture).
Oil amount Increase oil amount by about 5
cm3 (0.2 US oz, 0.2 Imp.oz).
Compression Turn adjuster counterclock-
damping force wise (about 2 clicks) to de-
crease damping.
Balance with Set sunken length for 90–95
“Obtrusive” rear end mm (3.5–3.7 in) when one
front, tending to passenger is astride seat (up-
upper front pos- per rear posture).
ture
Spring Replace with soft spring.
Oil amount Decrease oil amount by about
5–10 cm3 (0.2–0.3 US oz, 0.2–
0.4 Imp.oz).
TIP
• If any of the following symptoms is experienced with the standard position as the base, make reset-
ting by reference to the adjustment procedure given in the same chart.
• Adjust the rebound damping in 2-click increments or decrements.
• Adjust the low compression damping in 1-click increments or decrements.
• Adjust the high compression damping in 1/6 turn increments or decrements.
Section
Symptom Medi- Check Adjust
Large Small
Jump um
gap gap
gap
Rebound Turn adjuster counterclock-
damping force wise (about 2 clicks) to de-
Stiff, tending to crease damping.
sink Spring set Set sunken length for 90–100
length mm (3.5–3.9 in) when one
passenger is astride seat.
Rebound Turn adjuster clockwise (about
damping force 2 clicks) to increase damping.
Spongy and un-
Low compres- Turn adjuster clockwise (about
stable
sion damping 1 click) to increase damping.
Spring Replace with stiff spring.
10-7
CHASSIS
Section
Symptom Medi- Check Adjust
Large Small
Jump um
gap gap
gap
Rebound Turn adjuster counterclock-
Heavy and damping force wise (about 2 clicks) to de-
dragging crease damping.
Spring Replace with soft spring.
Rebound Turn adjuster counterclock-
damping force wise (about 2 clicks) to de-
crease damping.
Low compres- Turn adjuster clockwise (about
sion damping 1 click) to increase damping.
Poor road grip-
High compres- Turn adjuster clockwise (about
ping
sion damping 1/6 turn) to increase damping.
Spring set Set sunken length for 90–100
length mm (3.5–3.9 in) when one
passenger is astride seat.
Spring Replace with soft spring.
High compres- Turn adjuster clockwise (about
sion damping 1/6 turn) to increase damping.
Spring set Set sunken length for 90–100
Bottoming out
length mm (3.5–3.9 in) when one
passenger is astride seat.
Spring Replace with stiff spring.
Rebound Turn adjuster clockwise (about
Bouncing damping force 2 clicks) to increase damping.
Spring Replace with soft spring.
Turn adjuster counterclock-
High compres-
wise (about 1/6 turn) to de-
sion damping
crease damping.
Stiff travel Spring set Set sunken length for 90–100
length mm (3.5–3.9 in) when one
passenger is astride seat.
Spring Replace with soft spring.
10-8
WIRING DIAGRAM
EAS1SME382
YZ250FH 2017
1. Crankshaft position sensor
2. AC magneto
3. Rectifier/regulator
4. Joint connector
5. Condenser
6. Coupler for connecting option-
al part
7. Engine stop switch
8. Neutral switch
9. ECU (electronic control unit)
10. Ignition coil
11. Spark plug
12. Fuel injector
13. Fuel pump
14. Intake air temperature sensor
15. Coolant temperature sensor
16. Throttle position sensor
17. Intake air pressure sensor
18. Ignition coil sub-lead
COLOR CODE
EAS1SME383
B Black
Gy Gray
L Blue
Lg Light green
O Orange
P Pink
R Red
Sb Sky blue
Y Yellow
B/L Black/Blue
B/R Black/Red
B/W Black/White
B/Y Black/Yellow
Br/W Brown/White
G/W Green/White
L/W Blue/White
P/B Pink/Black
R/B Red/Black
Y/B Yellow/Black
Y/W Yellow/White
postscript3-本文レイアウト準拠-.fm Page 1 Monday, May 23, 2011 1:39 PM
Genuine Yamaha Parts – Genuine Yamaha replacement parts are the exact same parts as the ones
originally equipped on your vehicle, providing you with the performance and durability you have come to
expect. Why settle for aftermarket parts that may not provide full confidence and satisfaction?
Genuine Yamaha Accessories – Yamaha only offers accessories that meet our high standards for quality
and performance. Buy with confidence, knowing your Genuine Yamaha Accessories will fit right and
perform right – right out of the box.
Yamalube – Take care of your Yamaha with legendary Yamalube oils, lubricants, and care products.
They're formulated and approved by the toughest judges we know: the Yamaha engineering teams that
know your Yamaha from the inside out.
Genuine Yamaha Service Manuals – Get the same factory manual for your vehicle that the technicians
at your authorized Yamaha dealer use. Service manuals are available through your Yamaha dealer or you
can order them directly through yamahapubs.com.
Genuine Yamaha products are available only from your Yamaha dealer.
Q Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
YZ250FH
2017 OWNER’S SERVICE MANUAL
YZ250FH
PRINTED ON RECYCLED PAPER PRINTED IN JAPAN LIT-11626-30-23 1SM-28199-13
2016.04––1.2 × 1 !
(E)
L L L R R R R R R R
B B B B B B/L B/L B/L B/L B/L B/L
O R
R O
B/L Gy B/L Gy
R R R
Gy B R B
Gy
O O O
B R B/W Lg R
W W R
R R
W W Lg
R Lg O
R B
W W B/W
B R
W W W W
W W
B R R/B
R/B R/B R
B/W
B/Y
B/Y
B B B/R B/R R
B/Y B
ON
OFF
B/R R
B B
Br/W B/L
G/W B/L
L
L Y B/L
B/Y P P P
P Y Y
Sb Sb Sb
Y/W B/L
L/W Y/W Y/B
B/R
P/B
Y/B
Y/W P
Sb
B/L
L
P Y/B B/L
Sb P/B
B/L P/B L
ON
OFF