Professional Documents
Culture Documents
Manual Gaoke - Komax
Manual Gaoke - Komax
enable#: telmex
#hostname KOMAX_SEDE_XXXX
IAD(2)#set ip
WAN
->**Data port IP Address[138.0.60.1]:
->**Net Mask[255.255.0.0]:
->**voice port IP Address[138.1.60.1]: 10.116.248.66
->**Net Mask[255.255.0.0]: 255.255.255.252
LAN
->**IP Address[192.168.1.1]:
->**Net Mask[255.255.255.0]:
Public Network ipaddress in LAN
->Enable Public Netwok IPAddress in LAN? 'yes' or 'no'[no]: no
Second Public Network ipaddress in LAN
->Do you want to use The Second Public Netwok LAN? 'yes' or 'no'[no]: no
->**Whether Use the Default Gateway, 'yes' or 'no'[no]: yes
->**Default Gateway Address[0.0.0.0]: 10.116.248.65
IAD(2)#set vlan
Enable voice VLAN 'yes' or 'no'[yes]:no
Enable data VLAN 'yes' or 'no'[yes]:no
Port 1 Configuration:
Mode (0-route, 1-bridge)[0]:
Port 2 Configuration:
Mode (0-route, 1-bridge)[0]:
Port 3 Configuration:
Mode (0-route, 1-bridge)[0]:
Port 4 Configuration:
Mode (0-route, 1-bridge)[0]:
IAD(2)#save
Are you sure save current configuration? 'yes' or 'no'[no]: yes
erased 21 kbytes ... 100% complete.
Operate Successfully!
IAD(2)#sh allconfig
IAD(2)#reset
Are you sure reset device? 'yes' or 'no'[no]: yes
IAD(2)#ping 10.116.248.66
Sending 5, 100-bytes ICMP Echoes to 10.116.248.66 , timeout is 2 seconds...
!!!!!
Success rate is 100 percent(5/5),round-trip(ms) min/avg/max = 0.0/2.0/10.0
IAD(2)#ping 10.116.248.65
Sending 5, 100-bytes ICMP Echoes to 10.116.248.65 , timeout is 2 seconds...
!!!!!
Success rate is 100 percent(5/5),round-trip(ms) min/avg/max = 0.0/2.0/10.0
IAD(2)#set mgcp
->**Gateway Name[138.0.60.1]: LIMGA02mg25977177
->**Gateway Port(Default port is 2427, and not within RTP port range)[2427]:
->**RTP Port From(Default:3000, must more than 1024 and be even)[3000]:
->**Calling Agent Address:[10.136.2.76]: 10.95.190.133
->**Calling Agent Port(Default port is 2727)[2727]:
->**Use Backup calling agent?'yes' or 'no'[yes]: yes
->**Backup Calling Agent Address[10.136.2.96]: 10.136.2.44
->**Backup Calling Agent Port(Default Port is 2727)[2727]:
->**Mode of Port Register(0-Single Match, 1-All Match)[1]: 1
->**Transaction handle mode(0-step, 1-loop)[1]: 1
->Mode of Number Transmit(0-single digital, 1-String)[1]: 1
->**Type of SoftSwitch(0-HUAWEI,1-NORTEL,2-ZTE,3-other)[1]: 0
->Enable Inverpolar signal for accounting?'yes' or 'no'[yes]: yes
->**Enable active heartbeat?'yes' or 'no'[no]:no
->**Enable passive heartbeat?'yes' or 'no'[no]:no
->Sending Event with package name?'yes' or 'no'[yes]: yes
->Appoint the IP address in SDP?'yes' or 'no'[no]:no
IAD(2)#save
Are you sure save current configuration? 'yes' or 'no'[no]: yes
erased 21 kbytes ... 100% complete.
Operate Successfully!
IAD(2)#reset
Are you sure reset device? 'yes' or 'no'[no]: yes
IAD(2)#set tos
->**Please enter the MGCP packet's TOS value(0~255)[160]:160
->Please enter the voice packet's TOS value(0~255)[160]:160
Are you sure change configuration? 'yes' or 'no'[yes]: yes
IAD(2)#set codec
-> Batch All Endpoint Codec'yes' or 'no'[yes]:
IAD(2)#save
Are you sure save current configuration? 'yes' or 'no'[no]: yes
erased 21 kbytes ... 100% complete.
Operate Successfully!
IAD(2)#reset
Are you sure reset device? 'yes' or 'no'[no]: yes
IAD(2)#sh allconfig
Password:
Login success!
IAD(2)>ena
Password:
Komac_Malecon5#sh allconfig
Configuration of ip packets
==============================
MGCP packets TOS value : 160
IP voice packets TOS value : 160
Komac_Malecon5#
Komac_Malecon5#