Professional Documents
Culture Documents
U Wert Berechnung
U Wert Berechnung
outside
60 9
5 8
50 7
3 6
290
110
www.ubakus.de
5
27 4
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
3
10
12,5 1 2
inside
60 600
1 Rigips 1-Mann-Feuchtraumplatte "Die Grüne" (12,5 mm) 6 HASIT DIEPLAST 865 MINERAL Klebe- und Armierungsmörtel (3 mm)
2 Stationary air (10 mm) 7 weber.therm EPS 040 Fassade (50 mm)
3 Rigips 1-Mann-Feuchtraumplatte "Die Grüne" (12,5 mm) 8 HASIT DIEPLAST 865 MINERAL Klebe- und Armierungsmörtel (5 mm)
4 Stationary air (27 mm) 9 Knauf Insulation Fassaden-Dämmplatte FPL-040 (60 mm)
5 solid bricks, 1000 kg/m3, 1952 (110 mm)
*Vergleich mit dem Höchstwert gemäß GEG 2020 für erstmaligen Einbau, Ersatz oder Erneuerung von Außenwänden (Anlage 7, Zeile 1a,1b). Page 1
All statements without guarantee
Temperature profile
Temperature profile
Temperature
20
1 Dew point
15 2
10 3 4 5 6 7 8 9
Temperature [°C]
5
0 outside
-5
-10
-15
-20 www.ubakus.de
-25
0 50 100 150
200 250 300 inside
Inside 0°C [mm]
www.ubakus.de
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
Outside 60 600
1 Rigips 1-Mann-Feuchtraumplatte "... 4 Stationary air (27 mm) 7 weber.therm EPS 040 Fassade (50 mm)
2 Stationary air (10 mm) 5 solid bricks, 1000 kg/m3, 1952 (110 mm)
8 HASIT DIEPLAST 865 MINERAL Kl...
3 Rigips 1-Mann-Feuchtraumplatte "... 6 HASIT DIEPLAST 865 MINERAL Kl... 9 Knauf Insulation Fassaden-Dämmp...
Left:Temperature and dew-point temperature at the place marked in the right figure. The dew-point indicates the
temperature, at which water vapour condensates. As long as the temperature of the component is everywhere above the dew
point, no condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Right: The component, drawn to scale.
Page 2
All statements without guarantee
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 23°C und 50% Humidity; outside: -20°C und 65% Humidity (Climate according to user input).
This component is free of condensate under the given climate conditions.
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
Armierungsmörtel
7 5 cm weber.therm EPS 040 Fassade 2,50 - 0,8
8 0,5 cm HASIT DIEPLAST 865 MINERAL Klebe- und 0,10 - 5,8
Armierungsmörtel
9 6 cm Knauf Insulation Fassaden-Dämmplatte 0,06 - 2,4
FPL-040
29 cm Whole component 4,33 140,3
Humidity
The temperature of the inside surface is 19,9 °C leading to a relative humidity on the surface of 60%.Mould formation is not
expected under these conditions.
The following figure shows the relative humidity inside the component.
3 4 5 6 7 8 9
70
60
outside
50
40
30
20
10
www.ubakus.de
0
0 50 100 150 200 250 300 inside
Inside 0°C [mm]
www.ubakus.de Outside 60 600
1 Rigips 1-Mann-Feuchtraumplatte "... 4 Stationary air (27 mm) 7 weber.therm EPS 040 Fassade (50 mm)
2 Stationary air (10 mm) 5 solid bricks, 1000 kg/m3, 1952 (110 mm)
8 HASIT DIEPLAST 865 MINERAL Kl...
3 Rigips 1-Mann-Feuchtraumplatte "... 6 HASIT DIEPLAST 865 MINERAL Kl... 9 Knauf Insulation Fassaden-Dämmp...
Notes: Calculation using the Ubakus 2D-FE method. Convection and the capillarity of the building materials
were not considered. The drying time may take longer under unfavorable conditions (shading, damp / cool
summers) than calculated here.
Page 3
All statements without guarantee
Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:
Temperature profile
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of
32 2
3 1 Rigips 1-Mann-Feuchtraumplatte "Die Grüne" (12,5 mm)
30
Temperature [°C]
4 5 6
28 2 Stationary air (10 mm)
7 8 9
26 3 Rigips 1-Mann-Feuchtraumplatte "Die Grüne" (12,5 mm)
24 4 Stationary air (27 mm)
5 solid bricks, 1000 kg/m3, 1952 (110 mm)
22
6 HASIT DIEPLAST 865 MINERAL Klebe- und Armierungsmörtel (3 mm)
20
7 weber.therm EPS 040 Fassade (50 mm)
18
8 HASIT DIEPLAST 865 MINERAL Klebe- und Armierungsmörtel (5 mm)
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
16
9 Knauf Insulation Fassaden-Dämmplatte FPL-040 (60 mm)
14
0 50 100 150 200 250 300
Inside [mm]
www.ubakus.de Outside
Phase shift* 10,2 h Heat storage capacity (whole component): 139 kJ/m²K
Amplitude attenuation ** 31,2 Thermal capacity of inner layers: 108 kJ/m²K
TAV *** 0,032
* The phase shift is the time in hours after which the temperature peak of the afternoon reaches the component interior.
** The amplitude attenuation describes the attenuation of the temperature wave when passing through the component. A value of 10
means that the temperature on the outside varies 10x stronger than on the inside, e.g. outside 15-35 °C, inside 24-26 °C.
*** The temperature amplitude ratio TAV is the reciprocal of the attenuation: TAV = 1 / amplitude attenuation
Note: The heat protection of a room is influenced by several factors, but essentially by the direct solar radiation through windows and the
total amount of heat storage capacity (including floor, interior walls and furniture). A single component usually has only a very small
influence on the heat protection of the room.
The calculations presented above have been created for a 1-dimensional cross-section of the component.
Page 4