Professional Documents
Culture Documents
Monolithic Linear IC
Features
• Total output (EIAJ power): 30W+30W (at VCC = 14.4V, RL = 4Ω, THD = 30%)
• High-fidelity design (fL < 10Hz, fH = 130kHz)
• Extremely low impulse noise levels
• An arbitrary amplifier startup time can be set up with external components
• built-in standby switch circuit
• Full complement of built-in protection circuits (includes circuits that protect against shorting to VCC, shorting to ground,
load shorting, over-voltages and excessive temperatures)
Specifications
Maximum Ratings at Ta = 25°C
Parameter Symbol Conditions Ratings Unit
Maximum supply voltage VCC max No signal 18 V
Surge supply voltage VCC surge t ≤ 0.2s, Giant pulse one-shot 50 V
Maximum output current IO peak Per channel 3.0 A
Allowable power dissipation Pd max With a infinite heat sink 32 W
Operating temperature Topr -35 to +85 °C
Storage temperature Tstg -40 to +150 °C
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer' s products or
equipment.
Package Dimensions
unit : mm (typ)
3113B Pd max -- Ta
35
Infinite heat sink AI heat sink Mounting
Allowable power dissipation, Pd max -- W
26.8
32.5 torque 39N • cm
HEAT SPREADER 30 Flat washer Silicone
(20.0) 4.0 grease applied
(R1.7) θf = 3°C/W
25
θf = 4°C/W
20.83 θjc = 2°C/W
(8.4)
20
(11.8)
14.5MAX
θf = 7°C/W
7.0
15
7.8
13.9
10.4
θf = 10°C/W
10
4.6
5.2
1 14 5 Νο Fin
3.1
(1.83) 1.78 0.5 0.8 0.4
0
-40 -20 0 20 40 60 80 100 120 140 160
1.6 2.2
Ambient temperature, Ta -- °C
SANYO : SIP14HZ
No.5715-2/8
LA4725
Block Diagram
C2
100µF/25V VCC
+
2200µF
+
C5
25V
2 14
-OUT1 ñ
PREDRIVER POWER 13
0.1µF
C6**
C1
2.2Ω 2.2Ω
+
1 +
LOAD SHORT POWER R2 RL
IN 12
2.2µF − PROTECTOR GND1 4Ω
25V R3
0.1µF
C7**
PREDRIVER POWER 11
+OUT1
+
-OUT2 ñ
PREDRIVER POWER 9
0.1µF
IN2 C8**
C4
2.2Ω 2.2Ω
+
6 + LOAD SHORT POWER R4 RL
2.2µF IN 10
− PROTECTOR GND2 R5 4Ω
25V
0.1µF
C9**
PREDRIVER POWER 8
+OUT2 +
OUTPUT PIN TO VCC
SHORT PROTECTOR
POP NOISE
PREVENTION
CIRCUIT
5 7
0.47µF
33µF
+ +
25V
25V
C3 C10
C3 C10
Sets the amplifier starting time Impulse noise reduction
(Approximately 0.6 seconds when 33µF) (Note : The device’s ability to withstand shorting
to VCC or shorting to ground when VCC is
around 16V may be reduced as the value of this
capacitor is increased. We recommend 0.47µF.)
No.5715-3/8
LA4725
Pin Voltages
VCC = 13.2V, with 5V applied to STBY through a 10kΩ resistor, RL = 4Ω, Rg = 0
Pin No. 1 2 3 4 5 6 7
Pin name IN1 DC PRE-GND STBY ON TIME IN2 POP
Pin voltage 1.53V 5.65V 0V 3.25V 2.32V 1.53V 2.14V
Pin No. 8 9 10 11 12 13 14
Pin name +OUT2 −OUT2 PWR-GN +OUT1 PWR-GN −OUT1 VCC
Pin voltage 5.70V 5.70V 0V 5.70V 0V 5.70V 13.2V
External Components
C1 and C4: Input capacitors. A value of 2.2µF is recommended. Determine the polarity based on the DC potential of
the circuit connected directly to the LA4725 front end. Note that the low band response can be adjusted by
varying fL with the capacitors C1 and C4.
C2 : Decoupling capacitor (ripple filter)
C3 : Sets the amplifier starting time, which will be approximately 0.6 seconds for a value of 33µF. The starting
time is proportional to the value of this capacitor, and can be set to any desired value.
C5 : Power-supply capacitor
C6, C7, C8, and C9 :
Oscillation prevention capacitors. Use polyester film capacitors (Mylar capacitors) with excellent
characteristics. (Note that the series resistors R2, R3, R4, and R5 are used in conjunction with these
capacitors to achieve stable amplifier operation.) A value of 0.1µF is recommended.
C10 : Impulse noise reduction capacitor. A value of 0.47µF is recommended. Caution is required when selecting
the value for this capacitor, since increasing its value influences the operation of the circuits that protect
against shorting the amplifier output pins to VCC or to ground when higher VCC voltages (approximately
16V or higher) are used.
R1 : Standby switch current limiting resistor. A value of 10kΩ is recommended when a voltage in the range 2.5 to
12V will be applied as the standby switching voltage. Note that this resistor is not optional: it must be included.
2. Muting function
• Pin 5 connects the capacitor that determines the starting time to prevent impulse noise. It can also be used to mute
the amplifier output by shorting pin 5 to ground. When this function is used, the recovery time depends on C3.
No.6631-4/8
LA4725
4. Protection circuits
• Due to the system structure of the protection circuit for shorts to VCC or ground, if there is a DC resistance
between the amplifier output pins and ground, the protection circuit may operate when power is first applied and
the amplifier may fail to turn on. The basic design approach we recommend is not to adopt any designs in which
there is a DC resistance between the amplifier outputs and ground.
• The LA4725 includes a built-in thermal protection circuit to prevent the IC from being damaged or destroyed if
abnormally high temperatures occur. This thermal protection circuit gradually reduces the output if the IC
junction temperature (Tj) reaches the range 170 to 180°C due to inadequate heat sinking or other problem. If the
temperature falls, the amplifier will restart automatically.
• The LA4725 also includes other protection circuits. Use of these circuits also requires care during end product
design and testing.
5. Other notes
• The LA4725 is a BTL power amplifier. When testing this device, the ground systems for the test equipment
connected to IC inputs, and that for the test equipment connected to IC outputs, must be isolated. Do not use a
common ground.
GND
C5 14 1 LA4625/LA4725
VCC +
C1
IN1
+
+
-OUT1 C2
R2 C6
GND STB
R1
C3
+
+OUT1 +
R3 C7 IN2
C4
+
C10
-OUT2
GND R4 C8
+OUT2
R5 C9
No.6631-5/8
LA4725
PO -- VCC PO -- VIN
40 100
f = 1kHz 7 VCC = 13.2V
5
Rg = 600Ω RL = 4Ω
35 3
RL = 4Ω 2 f = 1kHz
30 10
Output power, PO -- W
Output power, PO -- W
7
% 5
25 30 3
= 2
THD
20 1.0
0% 7
=1 5
D
15 TH 3
2
10 0.1
7
5
5 3
2
0 0.01
6 7 8 9 10 11 12 13 14 15 16 17 18 1.0 2 3 5 7 10 2 3 5 7 100 2 3 5 7 1k
Supply voltage, VCC -- V Input voltage, VIN -- mVrms
PO -- f f Response
24 2
VCC = 13.2V
RL = 4Ω
Rg = 600Ω 0
20
Output power, PO -- W
16 THD = 10% -2
THD = 3% Response -- dB
12 -4
THD = 1%
8 -6
VCC = 13.2V
4 -8 RL = 4Ω
Rg = 600Ω
VO = 0dBm (f = 1kHz)
0 -10
10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k 10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k
Frequency, f -- Hz Frequency, f -- Hz
THD -- PO THD -- f
10 10
7 VCC = 13.2V 7 VCC = 13.2V
5 RL = 4Ω 5 RL = 4Ω
Total harmonic distortion, THD -- %
Total harmonic distortion, THD -- %
Rg = 600Ω PO = 1W
3 3
DIN AUDIO Nonfilter
2 2
1.0 1.0
7 7
5 5
3 3
2 2
f = 1kHz
0.1 0.1
7 10kHz 7
5 100Hz 5
3 3
2 2
0.01 0.01
0.1 2 3 5 7 1.0 2 3 5 7 10 2 3 5 7 100 10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k
Output power, PO -- W Frequency, f -- Hz
CHsep -- f VNO --VCC
-20 120
VCC = 13.2V Rg = 0
RL = 4Ω RL = 4Ω
Output noise voltage, VNO -- mVrms
Rg = 10kΩ 110
Channel separation, CHsep -- dB
-30
VO = 0dBm
Nonfilter
-40 100
CH1→2
-50 90
CH2→1 80
-60
-70 70
-80 60
2 3 5 7100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k 8 10 12 14 16 18
10
Frequency, f -- Hz Supply voltage, VCC -- V
No.6631-6/8
LA4725
SVRR -- VCC SVRR -- VCCR
-20 0
RL = 4Ω VCC = 13.2V
Rg = 0 RL = 4Ω
fR = 100Hz Rg = 0
-30
VCCR = 0dBm -20 Nonfilter
DIN AUDIO
-40
-40
OUT1
OUT1 100Hz
-50
T2
-60 z OU
100H
-60 UT1
OUT2 3kHz O
T2
-80 3kHz OU
-70
SVRR = 20log VO
VCCR
-80 -100
6 8 10 12 14 16 18 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Supply voltage, VCC -- V Power supply ripple, VCCR -- Vrms
SVRR -- fR ICCO -- VCC
0 160
VCC = 13.2V RL = 4Ω
RL = 4Ω Rg = 0
Rg = 0
Ripple rejection ratio, SVRR -- dB
140
VCCR = 0dBm
OU 100
T1
-60 OUT
2 80
-80
60
-100 40
10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k 6 8 10 12 14 16 18 20 22 36 36 36 36
Ripple frequency, fR -- Hz Supply voltage, VCC -- V
VN -- VCC Pd -- PO
12 25
RL = 4Ω RL = 4Ω
Rg = 0 Rg = 600Ω
10 f = 1kHz
20
Power dissipation, Pd -- W
8 V
.4
15 14
=
VN -- V
C V
6 VC 3.2
=1
10
V CC
4
5
2
0 0
5 10 15 20 25 30 0.1 2 3 5 7 1.0 2 3 5 7 10 2 3 5 7 100
Supply voltage, VCC -- V Output power, PO -- W
Amp ON time
0.6
VCC = 13.2V
VST = 5V
0.5
Amp ON time -- s
0.4
0.3
0.2
0.1
0
1.0 2 3 5 7 10 2 3 5 7 100
C3 -- µF
No.6631-7/8
LA4725
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of April, 2009. Specifications and information herein are subject to change
without notice.
PS No.5715-8/8