Professional Documents
Culture Documents
Track-Bridge Interaction on
High-Speed Railways
Editors
All rights reserved. No part of this publication or the information contained herein may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, by
photocopying, recording or otherwise, without written prior permission from the publishers.
Although all care is taken to ensure integrity and the quality of this publication and the information
herein, no responsibility is assumed by the publishers nor the author for any damage to the property or
persons as a result of operation or use of this publication and/or the information contained herein.
Preface VII
List of Authors IX
1 New evolutions for high speed rail line bridge design criteria and corresponding
design procedures 1
D. Dutoit
2 Service limit states for railway bridges in new Design Codes IAPF and Eurocodes 7
J.M. Goicolea-Ruigómez
5 Track-structure interaction and seismic design of the bearings system for some
viaducts of Ankara-Istanbul HSRL project 37
F. Millanes Mato & M. Ortega Cornejo
6 Track structure interactions for the Taiwan High Speed Rail project 55
D. Fitzwilliam
V
VI Table of Contents
14 Dynamic aspects of the high-speed railway bridge across the Hollandsch Diep 165
J.T.F.M. Tünnissen
16 Track-bridge interaction in railway lines: Application to the study of the bridge over
the River Moros 201
R. Simões, R. Calçada & R. Delgado
The construction of high-speed railways comprises a set of demands, from safety aspects to
new types of equipment and construction solutions, involving the most recent and sophisticated
technologies.
Among these, emphasis is given to the railway behaviour where the structural elements are of
great relevance. One of the relevant aspects concerns the effects of the track-bridge interaction,
which establishes restricted limits to the vibration and deformability of the structure in order to
control the acceleration, the stresses and the track deformations, so that the circulation safety is
satisfied, while strongly conditioning the structural design solutions for bridges.
The ability to address the multiple issues relevant to this process requires expertise and know-
how, which have been recently developed in this field, with repercussions in terms of the European
regulations in this domain.
The themes included in this book are mainly based on the papers presented at the workshop
“TRACK-BRIDGE INTERACTION ON HIGH-SPEED RAILWAYS” organised by the Faculdade
de Engenharia da Universidade do Porto (FEUP) and the Escuela Tecnica Superior de Ingenieros de
Caminos Canales y Puertos de Madrid (ETSICCyP). This book is included in a set of three books:
one with a more general thematic “BRIDGES FOR HIGH-SPEED RAILWAYS” and other with
a more focused thematic, such as the present book, “DYNAMICS OF HIGH-SPEED RAILWAY
BRIDGES”.
The editors would like to thank all those who contributed to this book, in particular our distin-
guished guest chapters’ authors who heightened, with their knowledge and expertise, to the present
interest and quality of the book, the support of the sponsors for the events which originated the
materials for this book, and the institutional support of the Faculty of Engineering of the University
of Porto and the RAVE – Rede Ferroviária de Alta Velocidade, S.A.
We hope this book will be helpful not only to those professionals involved in the design, construc-
tion or maintenance of high speed railway systems, but also to researchers and students working in
this field.
VII
List of Authors
IX
CHAPTER 1
New evolutions for high speed rail line bridge design criteria and
corresponding design procedures
D. Dutoit
Systra, Paris, France
ABSTRACT: The high speed rail lines bridges have always had specific design criteria. Never-
theless, with the new development of the analysis of rail stresses due to rail structure interaction,
some of the initial criteria used in France can be replaced by limitation of the rail stresses, as
described for instance in the Eurocode. This can lead to significant savings, especially in highly
seismic zones.
1
2 Track-Bridge Interaction on High-Speed Railways
In order to address the concerns described above, specific design criteria had been developed by
several national codes.
These specific criteria involved:
• A limitation of maximum distance between bridge expansion joints when using a continuous
welded rail, in order to limit the additional stress in the rail due to the difference of displacement
between the structure and the rail.
• A maximum rotation at bridge ends in order to limit the additional stress in the rail due to bridge
end displacement and the corresponding force transmitted by the elasticity of the ballast or of the
rail supports in the case of slab track and to ensure the stability of the ballast. This may control
the deck rigidity.
• A maximum displacement of the bridge when the maximum braking and acceleration force is
applied: this may control the foundation, pier and bearing design.
In the new evolution, instead of controlling the additional stresses in the rail by the above
mentioned limitations, a complete analysis of the additional stresses in the rail due to the bridges
supporting the track is limited to the followings
• 72 N/mm2 compression (Risk of track buckling in compression)
Ballasted track
• 92 N/mm2 tension
3 MAIN CONSEQUENCES
These new design procedures can induce a significant saving in the substructures (foundation,
piers). These savings may be magnified in seismic areas. Since the loads applied by a given
earthquake increase with the substructure rigidity, the additional elasticity of the substructure due
to the new HSR service load criteria will also induce a significant saving in the seismic analysis
of the structure.
The following examples show that the simplified method (no track structure interaction modelled)
used to avoid computerised calculation (track structure interaction modelled) is generally too con-
servative and cannot identify the critical points on the line where very high bearing reactions can
occur.
In the following examples, we compare the simplified method and the computerised method on
a simple case:
• Train type UIC 71
• Ballasted track
• Straight track
• Double track
• Rail type UIC 60
• Succession of 30 m simply supported spans.
4.1 Comparison between the simplified method and the computerised method – optimisation of
the pier and foundation
(a) Simplified method:
In the case of a succession of simply supported spans, the braking and acceleration forces applied
on one span are fully transmitted to the bearings of the span.
In the case of a 30 m simple span, the longitudinal braking and acceleration forces are:
The bearing reaction under temperature effect is calculated using the formula 8 × L (L is the
length of the span). It can be estimated at 8 kN/m × 30 m = 240 kN.
The maximum allowable relative displacement under braking and acceleration forces between
two decks is δ = 5 mm. Therefore, the minimum stiffness of the pier and foundation is:
F
K= = 318000 kN/m (2)
δ
Each pier and foundation shall have a stiffness higher than 318000 kN/m.
4 Track-Bridge Interaction on High-Speed Railways
Figure 2. Stresses in the rails under Temperature, braking/acceleration and live loads.
The stresses in the rail is between −25 MPa and +30 MPa.
The maximum bearing reaction is 1019 kN. This represents only 64% of the value given by the
simplified method (1590 kN).
It can also be noticed that the bearing reaction under temperature effect is almost zero compared
to 240 kN calculated by the simplified method.
(c) Analysis of the results:
The table below shows the results of the computerised calculations.
Table 1.
Results Allowable limits Ratio
In addition, the bearing reaction under temperature, braking/acceleration and live loads is only
56% of the value given by the simplified method.
(d) Conclusion:
It is therefore possible to optimise the piers and foundation. Additional calculations show that even
if the pier stiffness is reduced by more than 2, the safety of the track is still ensured.
The bearing reactions calculated by the computerised method are also around half of the value
calculated by the simplified method.
4.2 Comparison between the simplified method and the computerised method – Identification
of the critical points on the line
Due to the link between adjacent girder created by the track, a force applied on one span is
transmitted to the adjacent spans.
6 Track-Bridge Interaction on High-Speed Railways
In some case, where there is a sudden variation of pier stiffness, a bearing reaction may be higher
than the one calculated using the simplified method (see 4.1.a). The simplified method is, in these
cases, too favourable.
The case studied here is the same than the previous one (pier stiffness equal to 318000 kN/m),
but one pier has a stiffness much higher than the other (due for example to a sudden variation of the
ground level). We study in detail the bearing reactions on this pier under braking and acceleration
forces.
25 span (30 m)
Conclusion
The maximum bearing reaction is 2036 kN, which is 128% of the value calculated using the
simplified method (1590 kN – see 4.1.a).
Additional calculations shows that, in case of slab track, it is even more unfavourable. The
maximum bearing reaction is then 155% of the value calculated using the simplified method.
The new computarised method allows therefore a better identification of the overstressed areas,
and allows to make the required changes necessary to have a safer track.
CHAPTER 2
J.M. Goicolea-Ruigómez
Escuela de Ingenieros de Caminos, Technical University of Madrid, Spain
ABSTRACT: The new and enhanced performance needs of bridges for high-speed railway lines
have prompted new requirements for design of structures. These have been studied at national and
international level within Europe (ERRI, UIC, Eurocode project teams) and have originated new
engineering codes for actions and design requirements. Between these we may cite the Eurocodes
EN1991-2 (2003) and EN1990-A1 (2005) and the new Spanish code IAPF (2007). An important
feature in these codes is the consideration of service limit states. These limit states are unique to
railway bridges and are often the critical features conditioning the design. Among these limits are
the maximum of displacements and stresses in the rail related to track-bridge interaction, and the
limit of accelerations at the track. It must be stressed that some of these service limit states are
indeed ultimate limit states related to safety of rail traffic, and hence of the utmost importance.
In this work we shall review these limitations, the methods proposed for calculation, and their
relevance for design.
New high speed railway lines are developing at a fast pace in some European countries. In particular,
in Spain the plan for transport infrastructure (PEIT 2005–2020) devotes 78000 Million a to high
speed railways out of a total investment of 241000 Million a.
Railway bridges for the new high speed lines introduce a number of design requirements which
cause significant differences not only with road bridges but also with other railway bridges in
conventional freight or passenger lines. A first and obvious requirement arises directly from the
higher speed of traffic actions. These not only produce a higher individual effect (measured through
the impact factor ), but more importantly for speeds above 200 km/h the risk of resonance appears.
As a result dynamic analyses must be carried out in general, and furthermore these considerations
must be taken into account in the design of structural characteristics. In particular, some structural
types such as short span isostatic bridges have been shown to originate high levels of vibration
exceeding the limits for comfort and safety.
Furthermore the stricter requirements for the high speed lines (e.g. maximum gradients, mini-
mum radii) and geometrical quality originate line layouts in which more and longer viaducts are
necessary. This is particularly important in regions with rugged terrain like the Iberian Peninsula.
For instance, the new lines in Spain include a number of viaducts longer than 1000 m, some even
reaching 3000 m.
The consideration of interaction between bridge and track introduces additional requirements to
be met by railway bridges. These stem from limitations of stresses in the rail as well as maximum
values of relative displacements in deck joints. The magnitude of the track-bridge interaction
effects increases with the continuous length (expansion length LT ) of the deck. As a result, in short
7
8 Track-Bridge Interaction on High-Speed Railways
bridges these requirements are not especially restrictive. However in long viaducts, of the lengths
commonly required by high speed line layouts, they prove to be an important restriction and must
be considered at early stages of design. One option which has been adopted in some lines is to
limit the continuous length of the decks, splitting long viaducts into individual simply supported
structures. This option may be overly restrictive. Moreover, it bears the disadvantage expressed
above that simply supported beam structures develop generally higher vibration response to traffic
loads. Furthermore, the optimization of construction procedures in some cases makes advantageous
the progressive launching or pushing of a long continuous deck.
The above considerations have led the administration and the infrastructure manager (ADIF)
in Spain to allow the construction of long continuous viaducts, exceeding in some cases 1000 m
length. The bases for calculation and associated limits are defined in IAPF (2007) and at a European
level in EN1991-2 (2003).
In the remaining of this paper, in section 2 we shall firstly review some design considerations for
high speed railway bridges, with special emphasis on those originating from dynamic behaviour.
Following, in section 3 we shall review the methods and requirements for track-bridge interaction in
the codes, focusing on the new IAPF (2007) compared to EN1991-2 (2003). Here the serviceability
limit state checks regarding deformations of the deck will be discussed critically. The paper finishes
with a summary of the main conclusions in section 4.
Dynamic response of railway bridges is a major factor for design and maintenance, especially in
new high speed railway lines. The main concern is the risk of resonance from periodic action of
moving train loads. In cases when such risk is relevant (e.g. for speeds above 200 km/h) a dynamic
analysis is mandatory.
The new engineering codes [EN1991-2 (2003), EN1990-A1 (2005), IAPF (2007), FS. (1997)]
take into account these issues and define the conditions under which dynamic analysis must be
performed. They provide guidelines for models, types of trains to be considered, and design criteria
or limits of acceptance [Goicolea, J.M. (2004)].
Resonance for a train of periodically spaced loads may occur when these are applied sequentially
to the fundamental mode of vibration of a bridge and they all occur with the same phase, thus
accumulating the vibration energy from the action of each axle. If the train speed is v, the spacing
of the loads D and the fundamental frequency f0 , defining the excitation wavelength as λ = v/f0 ,
the condition for critical resonant speeds may be expressed as [EN1991-2 (2003)]:
D
λ= , i = 1, . . . 4. (1)
i
Although the basic dynamic phenomena due to moving loads are known since long (e.g. see
the book by Fryba, L. (1972)) it has not been until recently that resonance phenomena in bridges
from high speed traffic have been well understood and practical methods of analysis developed
[ERRI D214. (2002), Domínguez J. (2001)]. From a technical point of view a number of methods
for dynamic analysis are available for engineering practice. Briefly, the available methods are: a)
dynamic analysis with time integration and moving loads; b) dynamic analysis with time integra-
tion and bridge-vehicle interaction; and c) dynamic envelopes based on train signature methods.
Rather than discussing these methods here, for which a complete description is given elsewhere
[Domínguez, J. (2001), Goicolea, J.M. (2004)] we shall focus on the relevance of dynamic effects
for structural designs.
In railway bridge design often the most restrictive conditions in practice are the Serviceability
Limit States (SLS) [EN1990-A1 (2005), Nasarre J. (2004)] (maximum acceleration, rotations and
deflections, etc.). Accelerations must be independently obtained in the dynamic analysis. In the
example shown in Figure 1, for a short span simply supported bridge, both maximum displacements
and accelerations are obtained independently and checked against their nominal (LM71) or limit
Service limit states for railway bridges in new Design Codes IAPF and Eurocodes 9
values respectively. It is clearly seen that for a resonant train speed the deflection limits are above
the LM71 nominal values, resulting in an impact factor greater than unity. A more severe effect is
the accelerations which surpass by far the limits, thus invalidating this (purely theoretical) design.
Further details may be seen in Goicolea, J.M. (2004). These results have been obtained both with
moving loads and with bridge-vehicle interaction, showing that the gain of considering this latter
and more advanced model, albeit significant in this case, still yields a non acceptable value.
In order to consider the resonant velocities for dynamic calculations, these must be performed
generally for all possible speeds. The results may be presented as envelopes of resulting magnitudes
in these velocity sweeps. Following we present a typical set of such calculations showing the fact
that generally resonance may be much larger for short span bridges. In this representative example,
Figure 2 shows the normalised displacement response envelopes obtained for ICE2 train in a
velocity sweep between 120 and 420 km/h at intervals of 5 km/h. Calculations are performed for
three different bridges, from short to moderate lengths (20 m, 30 m and 40 m). The maximum
response obtained for the short length bridge is many times larger that the other. The physical
reason is that for bridges longer than coach length at any given time several axles or bogies will
be on the bridge with different phases, thus cancelling effects and impeding a clear resonance. We
also remark that for lower speeds in all three cases the response is approximately 2.5 times lower
than that of the much heavier nominal train LM71. Resonance increases this response by a factor
of 5, thus surpassing by a factor of 2 the LM71 response.
A significant reduction of vibration is obtained in short span bridges under resonance by using
interaction models. This may be explained considering that part of the energy from the vibration
is transmitted from the bridge to the vehicles. However, only a modest reduction is obtained for
non-resonant speeds. Further, in longer spans or in continuous deck bridges the advantage gained
by employing interaction models will generally be very small. This is exemplified in Figure 2,
showing results of sweeps of dynamic calculations for the three said bridges of different spans. As
a consequence it is not generally considered necessary to perform dynamic analysis with interaction
for project or design purposes.
The above results are not merely theoretical considerations. It has been seen in practice that
they reflect accurately the vibrations taking effect in real high speed railway bridges. To show
this we comment some experimental results on an existing high speed bridge. Figure 3 shows the
measured resonant response in the bridge over the river Tajo in the Madrid-Sevilla HS line. The
bridge consists of a sequence of simply supported isostatic decks with spans of 38 m. The dynamic
amplification in this case is noticeable. In spite of this, design responses keep within required
limits. However, it is clear that the dynamic performance could be improved by a different structural
design.
Another well-known issue is the fact that dynamic effects in indeterminate structures, especially
continuous deck beams, are generally much lower than isostatic structures [Domínguez, J. (2001)].
The vibration of simply supported beams is dominated clearly by the first mode, and moreover
only the loads on the span under consideration excite the motion at a given instant. This makes
much more likely a resonant phenomenon, whenever condition (1) is met. On the contrary, the
vibration of continuous beams includes significant contributions of a number of modes, and loads
on other spans excite the motion of the span under consideration. As a result, the algebraic sum of
the effects tends to cancel to a large extent.
We show a practical example of this effect in a student project for the Arroyo del Salado viaduct
[Sanz, B. (2005)] on the Córdoba-Málaga High Speed Line, with a total length of 900 m and 30
spans of 30 m each. The section is a prestressed concrete box deck, and the proposed solution
was a continuous beam deck cast in-situ. The comparison of this solution with a corresponding
simply supported multiple span viaduct is shown in Figure 4, where it may be seen the much better
performance in terms of dynamic response of the continuous beam deck.
Finally, we discuss the consideration of different high speed train types. The existing trains in
Europe are defined in EN1991-2 (2003), IAPF (2007), and may be classified into conventional (ICE,
ETR-Y, VIRGIN), articulated (THALYS, AVE, EUROSTAR) and regular (TALGO). Variations of
these trains which satisfy interoperability criteria have been shown to covered by the dynamic
10 Track-Bridge Interaction on High-Speed Railways
Figure 1. Calculations for simply supported bridge from ERRI D214. (2002) catalogue (L = 15 m, f0 = 5 Hz,
ρ = 15000 kg/m, δLM71 = 11 mm), with TALGO AV2 train, for non-resonant (360 km/h, top) and resonant
(236.5 km/h, bottom) speeds, considering dynamic analysis with moving loads and with train-bridge interac-
tion. Note that the response at the higher speed (360 km/h) is considerably smaller than for the critical speed
of 236.5 km/h. The graphs at left show displacements, comparing with the quasi-static response of the real
train and the LM71 model, and those at right accelerations, compared with the limit of 3.5 m/s2 [EN1990-A1
(2005)].
Figure 2. Normalised envelope of dynamic effects (displacement) for ICE2 high-speed train between
120 and 420 km/h on simply supported bridges of different spans (L = 20 m, f0 = 4 Hz, ρ = 20000 kg/m,
δLM71 = 11.79 mm, L = 30 m, f0 = 3 Hz, ρ = 25000 kg/m, δLM71 = 15.07 mm and L = 40 m, f0 = 3 Hz,
ρ = 30000 kg/m, δLM71 = 11.81 mm). Dashed lines represent analysis with moving loads, solid lines with
symbols models with interaction. Damping is ζ = 2% in all cases.
Service limit states for railway bridges in new Design Codes IAPF and Eurocodes 11
Figure 3. Time history of displacements at centre of span in viaduct over Tajo river in HS line Madrid-Sevilla.
Simply supported deck with span 38 m, damping ratio ζ = 1.65%. Left graph shows measurements [MFOM
(1996)], right graph analytical calculations [Domínguez, J. (2001)]. Horizontal scale is time (s), vertical scale
displacements (mm).
Figure 4. Summary of dynamic analysis envelopes with universal HS trains HSLM showing maximum
accelerations in the deck. The graph on the left corresponds to the proposed design as continuous beam, which
satisfies the requirement for accelerations amax < 3.5 m/s2 . The right graph corresponds to a simple supported
bridge with the same deck section; in this case the requirement for maximum accelerations is not fulfilled for
high speeds.
effects of the High Speed Load Model (HSLM), a set of universal fictitious trains proposed by
ERRI D214. (2002). The use of this new load model is highly recommended for all new railway lines,
and incorporated into codes EN1991-2 (2003) and IAPF (2007). More importantly, consideration of
HSLM model is mandatory for interoperable lines following the European Technical Specifications
for Interoperability (TSI) in high speed lines [EC (2002)].
A useful way to compare the action of different trains and to evaluate the performance of HSLM
as an envelope is to employ the so-called dynamic train signature models. These develop the
response as a combination of harmonic series, and establish an upper bound of this sum, avoiding a
direct dynamic analysis by time integration. Their basic description may be found in [ERRI D214.
(2002)]. They furnish an analytical evaluation of an upper bound for the dynamic response of a
given bridge. The result is expressed as a function of the dynamic signature of the train G(λ). This
function depends only on the distribution of the train axle loads. Each train has its own dynamic
signature, which is independent of the characteristics of the bridge. The above expressions have
been applied in Figure 5 to represent the envelope of all real existing HS trains in Europe, together
with the envelope of HSLM.
12 Track-Bridge Interaction on High-Speed Railways
Figure 5. Envelope of dynamic signatures for European HS trains, together with the envelope of signatures
for High Speed Load Model HSLM-A, showing the adequacy of this load model for dynamic analysis.
– Forces transmitted to piers and abutments from combined actions of structure and track;
– Rail stresses due to variable actions, in particular thermal actions, braking and acceleration
longitudinal forces and vertical traffic loads;
– Relative movements and deformations at the ends of the deck due to the above variable actions.
Figure 6. Model to be considered for track-bridge interaction, in a simple case with one deck. The figure
shows a deck with one fixed point and two sliding supports, nonlinear “generalised springs” which model
the longitudinal interaction between track and deck, and an optional rail expansion device at one end (figure
translated from IAPF (2007)).
an intermediate point of the bridge; and c) multiple isostatic spans with fixed bearings ate the end
of each span.
The general type of model to be considered is depicted schematically in Figure 6, for case a)
above. This model considers the track and the deck (both considered deformable elastically), the
piers, and the abutments which may also be flexible. A key aspect in the model is the proper
consideration of the interaction forces between rail and deck, in the figure represented through
generalised springs, which as we shall see below are of nonlinear nature. Finally, in the fig-
ure a rail expansion device which would signify a longitudinal discontinuity for the rail is also
shown.
A characteristic value of these models is the so-called expansion length LT . In the example
shown it would be simply the length of the deck between the fixed support on one abutment and the
free-sliding joint on the other abutment. The greater the value of LT the greater interaction effects
will be introduced at the free sliding joint.
When expansion lengths are large the rail stresses may be reduced by the introduction of rail
expansion devices. In such case, the horizontal deck forces would be transferred integrally to the
fixed bearing, alleviating the effects on the rail. However, rail expansion devices are generally
undesirable from the point of view of track engineering and maintenance. Expansion lengths of
the order of 100 m may generally be accommodated without resorting to rail expansion devices.
Expansion lengths of the order of 300 m to 400 m will very probably necessitate at least one
rail expansion device. Expansion lengths greater that this may necessitate at least two expansion
devices, say with a fixed point at the center, or other structural solutions.
The above mentioned nonlinear generalised springs are defined with bilinear laws, of the type
shown in Figure 7. The first branch represents an elastic behaviour, whereas after a given dis-
placement u0 the sliding limit is attained and the constant resistance k is developed. The Eurocode
EN1991-2 (2003) leaves the values of (u0 , k) open, to be defined in national annex or other project
specifications. The code IAPF (2007) defines values for u0 between 0.5 and 2.0 mm, and for k
between 20 and 60 kN/m, depending on the type of track, vertical load etc.
The structural model described may be developed within a discretised computer model of the
structure with nonlinear material capabilities, such as finite element or other numerical programs.
This program must have the capability to solve the resulting set of nonlinear algebraic equations,
generally using an iterative procedure by Newton-type iterations until convergence is reached. An
essential characteristic of nonlinear models is that superposition of actions is not valid; hence for
each calculation the complete set of actions must be applied in the correct sequence to the model.
In particular for this case, for each scenario selected the thermal actions would be applied first and
then the vertical and longitudinal traffic actions.
14 Track-Bridge Interaction on High-Speed Railways
Figure 7. Force-displacement interaction law between track and deck. The parameter u0 defines the maximum
relative displacement at which sliding starts, with a plasticity or friction-type resistance defined as k. Particular
values of u0 and k are defined in IAPF (2007) for different types of tracks and situations. (figure translated
from IAPF (2007)).
For short expansion lengths LT both codes allow simplified procedures for calculation. In par-
ticular, for LT ≤ 40 m in EN1991-2 (2003) or LT ≤ 60 m (steel) – 90 m (concrete) in IAPF (2007)
it may be considered that rail expansion devices are not needed, without a full justification by
the nonlinear models above described. For somewhat longer expansion lengths, LT ≤ 110 m, the
code IAPF (2007) refers to the simplified procedures defined in UIC (1999) based on charts for
evaluating the interaction.
Furthermore, the Eurocode EN1991-2 (2003) allows the simplification, for evaluating forces
in rails and bearings, of combining linearly the effects of the different actions. As has been said
before, strictly speaking this linear combination is not valid; however for computation of forces
in general a conservative result will be obtained. This is not generally the case for calculation of
deformations, which may be underestimated using this simplification. In the Spanish code IAPF
(2007) this simplification is not considered.
Figure 8. Maximum longitudinal relative displacement from braking or acceleration actions (δ2 in IAPF
(2007) or δB in EN1991-2 (2003)) between two ends at a joint (figure from IAPF (2007)).
Figure 9. Maximum horizontal relative displacement from bending due to vertical or eccentric horizontal
actions (δ3 in IAPF (2007) or δH in EN1991-2 (2003)) between two ends at a joint (figure from IAPF (2007)).
In the Spanish code IAPF (2007) again this limit (called δ4 ) is more precisely defined not as
vertical but as normal to the rail within a vertical plane. Figure 10 shows a schematic repre-
sentation of this movement. As may be seen there could be a noticeable difference between the
normal movement which actually alters the track geometry in a track with gradient, and the
vertical movement which would be zero in this case. For a long viaduct this difference may be
critical.
Furthermore to the above requirements, the following limit is defined in IAPF (2007), but not
in the Eurocode EN1991-2 (2003):
– The relative movement between rail and deck (or between rail and abutment platform) must be
δ1 ≤ 4 mm under the actions for acceleration and braking. This requirement may also be found
in UIC (1999).
The above design requirements both for stresses in the rail as well as for movements at the ends
of the deck represent Serviceability Limit States (SLS) for the structure. However, in this case the
importance of these limit states is paramount, as they represent Ultimate Limit States (ULS) for the
railway traffic. It must be clearly understood by any structural engineer that these design criteria
16 Track-Bridge Interaction on High-Speed Railways
Figure 10. Maximum relative normal displacement in vertical plane from variable actions (δ4 in IAPF (2007)
or δV in EN1991-2 (2003)) between two ends at a joint (figure from IAPF (2007)).
are often the critical requirements for railway bridges, contrary to the case for road bridges. This
has been clearly set out in the paper by Nasarre J. (2004).
4 CONCLUSIONS
REFERENCES
Domínguez, J. (2001). Dinámica de puentes de ferrocarril para alta velocidad: métodos de cálculo y estudio
de la resonancia. Tesis Doctoral. Escuela Técnica Superior de Ingenieros de Caminos, Canales y Puertos
de Madrid (UPM), 2001. Publicada por la Asociación Nacional de Constructores Independientes (ANCI).
EC (2002). TSI-HS2002: Technical specification for Interoperability relating to the infrastructure subsystem
of the trans-European high-speed rail system. Commission decision 2002/732/EC 20 may 2002, 2002.
Official journal of the European Communities OJ L 12/9/2002.
EN1991-2 (2003). European Committee for Standardization. EN1991-2: EUROCODE 1 – Actions on
structures, Part 2: Traffic loads on bridges. European Union, 2003.
EN1990-A1 (2005). European Committee for Standardization. {EN1990-A1}: EUROCODE 0 – Basis of
Structural Design, Amendment A1: Annex {A2}, Application for bridges. European Union, 2005.
ERRI D214 (2002). Utilisation de convois universels pour le dimensionnement dynamique de ponts-rails.
Synthèse des résultats du D214.2 (Rapport final). European Rail Research Institute (ERRI).
ERRI D214 RP9 (1998). European Railway Research Institute subcommitee D214. Design of Railway Bridges
for Speed up to 350 km/h; Dynamic loading effects including resonance. Final report, November 1998.
FS (1997). Ferrovie dello Stato; Sovraccarichi per il calcolo dei ponti ferroviari.
Service limit states for railway bridges in new Design Codes IAPF and Eurocodes 17
Fryba, L. (1972). Vibration of solids and structures under moving loads. Academia, Noordhoff, 1972.
Goicolea, J.M. (2004). Dynamic loads in new engineering codes for railway bridges in Europe and Spain.
Workshop on Bridges for High Speed Railways, Porto 3–4 June 2004, Faculty of Engineering, University
of Porto.
IAPF (2007). Instrucción de acciones a considerar en el proyecto de puentes de ferrocarril. Ministerio de
Fomento de España, Dirección General de Ferrocarriles. Oct 2007.
MFOM (1996). Dirección general de ferrocarriles y transporte∼por carretera. Viaducto sobre el río tajo, línea
ave Madrid-Sevilla, ensayos dinámicos. Technical report, Ministerio de Fomento de España, 1996.
Nasarre, J. (2004). Estados límite de servicio en relación con los puentes de ferrocarril. In A. Campos R. Del-
gado, R. Calçada, editor, Bridges for High-Speed Railways, pages 237–250. Civil Engineering Dept.,
Faculty of Engineering of the University of Porto, 2004.
Sanz, B. (2005). Proyecto de viaducto para el ferrocarril de alta velocidad sobre el arroyo del salado. Master
thesis, Escuela de Ingenieros de Caminos, UPM, 2005.
UIC (1999). Code UIC 774-3R Interaction voie/ouvrages d’art, Recommandations pour les calculs. UIC,
Union Internationale des Chemins de Fer, Feb1999.
UIC (2006). Leaflet UIC 776-1R: Charges a prendre en consideration dans le calcul des ponts-rails. UIC,
Union Internationale des Chemins de Fer, 2006. 5 ed, Aug 2006.
CHAPTER 3
A.M. Cutillas
Technical University of Madrid & Carlos Fernández Casado S.L., Madrid, Spain
ABSTRACT: Track-bridge interaction problems have a main role in the design of bridges,
especially at conception stage of long viaducts with high or short piers in high speed railways
lines.
The presentation will focus on the main aspects of track bridge interaction aspects to be taken
into account in the design of these bridges:
• Bridge displacement limitations at track level
• Railway expansion joint needs
Some examples of recent bridges which have been designed in High speed railway lines in Spain
will be shown. A special attention will be paid to the Viaduct over the Guadalete river. It is a
3221.70 m long viaduct in which the aforementioned problems were determinant in the conception
and design of the bridge.
Railway bridges, in general and high speed railway bridges in particular have to resist important
horizontal loads.The horizontal loads are originated by the climate such as the wind. The wind acts
on the whole structure surface exposed, the piers and the deck as well as on the live load itself.
These loads produce bending moments of the deck’s vertical axis as well as twisting moments
which are added to the combined pier-deck effects produced by the live load.
The live loads produces two horizontal loads derived from the accelerations. On the one hand,
transverse radial accelerations in curved layouts, which bring about the centrifugal force. On the
other hand they bring about longitudinal accelerations produced by braking and traction forces.
The stresses due to the centrifugal forces produce the same effects as those derived from the
transverse wind. These forces can be very important for even though the radii are great so is the
speed (Fig. 1).
19
20 Track-Bridge Interaction on High-Speed Railways
The braking forces considered amount to 2 t/m according to EC-1, with a maximum application
length of 300 m. The traction forces, in their turn, equal 3,3 t/m with a maximum loaded length of
30 m. Consequently, for long viaducts (longer than 300 m) the maximum force transmitted to the
tracks will amount to 700 t. The force transmitted to the deck, bearings and piers will depend on
whether the expansion joints are arranged or not on the rail at one or both ends of the deck, as well
as on the total length (Fig. 2).
Within the whole made of the track (rail, sleepers, ballast), the deck, the bearings and the piers as
deformable elements with different mechanical properties there are force transferences produced
by external loads or deformations imposed, which bring about the well known phenomena of
track-deck interaction (Fig. 3).
When the rail is continuous and the track is supported on an element which is not very deformable
such as the ground, its sizing depends on the vertical and horizontal loads transmitted by the railway,
and the axial forces as a consequence of the deformations restrained by the temperature so the
strength reserve to failure is limited. When the tracks are placed over a structure, the imposed
deformations produced by the uniform temperature variations and by the creep and shrinkage
phenomena in the deck, produce relative displacements between the track and the deck that as a
consequence of friction forces with the ballast, produce horizontal loads over both the track and
the deck that may exhaust the resistant capacity of the rail. This is the reason why the arrangement
of the continuous rail is limited to concrete structures with a total expansion length not greater
than 90 m.
With the intention to optimise the design and viaducts construction conditions and track exploita-
tion in continuous viaducts it will be necessary, whenever it is possible, to arrange an expansion
joint in one of the abutments. In this way the phenomena of track-deck interaction disappear. Oth-
erwise, the viaducts would have to be sub-divided into smaller lengths with the resulting problems
of structural joints, duplication of the bearings and the placing of intermediate stiff and resistant
elements in order to resist the horizontal loads in each structure.
If all these factors are studied and properly balanced: the resistant problem for horizontal forces
and the track-deck interaction problems, different longitudinal configurations of the viaducts can
be obtained (Fig. 4):
• Long continuous viaducts fixed at one abutment with one big expansion joint on the rail at the
opposite one (Figs 2–3, 5).
• Long continuous viaducts with a stiff intermediate pier and two small expansion joints on the
rail at both abutments (Fig. 1).
• Continuous viaducts with a stiff intermediate pier with no expansion joints in the rails (Fig. 6).
Most of the continuous viaducts we present here are longitudinally fixed in one abutment and
have one expansion joint in the rail in the opposite. Since all these viaducts are incrementally
launched it is necessary to locate a segment casting yard on one of the abutments. These yards must
have the capacity, among other things, to resist the horizontal forces during the launching as well
as the loads produced by the wind and temperatures under rest conditions. These are, therefore,
elements able to be adapted to become anchorage elements of the deck under service conditions.
This is why most of the viaducts presented here, except the Viaduct 2 of the Sub-stretch VIII (Fig. 1)
and Martorell Viaduct (Fig. 6), are anchored in the abutment corresponding to the segment casting
yard. The abutment-yard whole is the structure in charge of transmitting to the ground the horizontal
forces produced by the braking and traction loads, the longitudinal wind and those produced by
friction forces of the elastomeric-teflon devices as a consequence of the deformations due to the
temperature, creep and shrinkage.
The total horizontal forces, under service conditions, are much greater than those corresponding
to the situation during construction for the following reasons:
During construction, the reactions in the supports produced by the horizontal forces correspond
to the total permanent load and not self weight.
The coefficient of friction of the teflon supports considered under service conditions amounts
to 5%, while during construction it amounts to 2.5%. Actually, the value of 2% is hardly reached
if special greases are used to reduce this coefficient.
Under service conditions we must take into account the braking and traction forces for viaducts
longer than 300 m reach a maximum value of 700 T.
In spite of the effectiveness of this structural disposition, we must bear in mind the fact that
the viaduct length imposes certain limits: on the one hand, the availability of expansion devices
able to admit great movements. At present, there are devices with the movement capacity of up
to 1200 mm, which establishes a length limit between 1200 and 1300 m for prestressed concrete
viaducts. On the other hand there is a limit, though higher than the previous one, which depends
on the capacity of the deck to admit the prestressing force that would counteract these horizontal
forces.
The concept of the Viaduct 2 of the sub-stretch VIII, mentioned before responds to the need to
reduce the movements in the expansion joint and to place the fixed point by a delta shaped pier on
a small hill in the valley. This disposition allows us to double the length of the viaducts by placing
two small expansion joints in the rail.
In MartorellViaduct and intermediateV shaped pier was designed. In order to resist the horizontal
forces and to reduce the longitudinal movements in this section, the pier is founded over slurry-walls
with a big longitudinal stiffness. (Fig. 6). The deck has a total length of 202 m, the expansion length
is 101 m (greater than 90 m). In order to avoid the expansion joints at the abutments a complete
track-deck interaction analysis was performed. The deck and rails were modelled connected with
Track-bridge interaction problems in bridge design 23
non linear springs corresponding to the mechanical behaviour of the ballast. The main conclusions
of the analysis were:
The stress increment in the rail due temperature actions was 42 MPa. (Fig. 8)
The maximum stress increment in the rail, in compression, due to temperature and braking-
traction forces was 77.6 MPa.
The longitudinal displacement in the deck due to braking-traction forces was 4.27 mm and
5.2 mm taking into account the foundation influence.
The braking force transferred to de deck is 80% of the total force applied at the rail level.
The length of the viaduct asks for a typological study taken into account track-deck inter-
action problems due to imposed deformations, horizontal loads and to the position of the rail
and deck expansion joints along the viaduct. In this study different structural, constructional and
environmental problems were considered (Fig. 11).
From the structural point of view, the strength to resist the horizontal forces due to braking and
seismic loads should be compatible with the flexibility to reduce as much as possible the stresses
due to thermal and long term deformations. It was decided to avoid any expansion joint on the rails
in order to improve as much as possible the exploitation of the railway. A maximum length of 200 m
between structural deck expansion joints was limited in order to avoid any overstressing on the rails
due to track-deck interaction problems. In order to fulfill all the environmental requirements, the
supports over the river beds were reduced as much as possible. A precast solution was designed to
allow industrialized construction procedures suited to a very long viaduct (Fig. 12).
The final solution adopted is a twin precast box girder 2.20 m deep and located below each
railway axis, 2.15 m apart. The total deck width is 13.0 m (Fig. 10). This deck allows to span the
length of 30 m as a simply supported structure along most of the length of the bridge and to span
49 m with the help of two additional precast arches. This concept allows with a very repetitive
structure to cross the longest spans due to the presence of Guadalete river beds and the road CA
Track-bridge interaction problems in bridge design 25
2011. With these criteria the viaduct is split in 7 stretches with the lengths and spans shown in
Table 1. (Fig. 13)
The use of continuous precast arches allows to balance the horizontal forces due to permanent
loads on the intermediate supports creating a well suited and new structure (Fig. 14).
1 823.50 27 30.50
2 207.00 2 30.00
3 49.00
3 810.00 27 30.00
4 207.00 2 30.00
3 49.00
5 547.20 18 30.40
6 207.00 2 30.00
3 49.00
7 420.00 14 30.00
Total 3221.70 101
rails. For the greater spans the continuous precast arches are able to resist properly the horizontal
loads with an expansion length to avoid any overstressing problems on the rails.
Preliminary analysis to control track-deck interaction problems were performed: the expansion
lengths limitation were fulfil so the maximum displacement due to braking loads should be limited
to 5 mm at deck level on the structural deck expansion joints. These displacements were obtained
taken into account the flexibility of the soil-foundation structure using the stiffness matrix of the
whole. It was assumed that all the braking loads are transmitted to the continuous deck which can
be considered as an upper limit of the total load because of the continuity of the rails (Fig. 15).
Track-bridge interaction problems in bridge design 27
Figure 17. Braking loads. Axial forces on the rail with soil structure-interaction model.
A detailed model for the track interaction problems was made in order to confirm the main
assumptions done in the preliminary analysis. The continuous precast arches were modelled with
plane bar elements. Four additional simply supported spans are added to avoid any perturbation
on the expansion joints results. The rails were included in the model as an additional structure.
The connection between the rail and the deck has been done with perfectly elastoplastic elements
which represent the track-deck behaviour, as it has been mentioned above. The maximum forces
and stiffnesses vary according the loaded or unloaded track situation (Fig. 16).
The different load cases were done in two different models:
1. Built-in model, in which the arches are completed built in the foundation
2. Model with soil-structure interaction: in which the soil-foundation stiffness matrix has been
included.
Three load cases have been considered on each model:
Figure 18. Braking loads. Axial forces on the rail built-in model.
Figure 19. Thermal action +20◦ C on the deck. Axial forces on the rail with soil structure-interaction model.
Figure 20. Thermal action +20◦ C on the deck. Axial forces on the rail in built in model.
REFERENCES
ENV 1991-3:1995. Eurocode 1. Basis of design and actions on structures. Part 3. Traffic loads on bridges.
Manterola, J., Astiz, M.A., Martínez, A. Puentes de ferrocarril de alta velocidad Revista de Obras Públicas
n◦ 3386 pp. 43–77 Abril (1999).
Manterola Armisén, J.; Martínez Cutillas, A. Prestressed concrete railways bridges Workshop Bridges for high
speed railways. Oporto (2004).
CHAPTER 4
S.G. Davis
Mott MacDonald, United Kingdom
ABSTRACT: In seismic regions, a major constraint affecting the design of high speed rail viaducts
is the track-structure interaction during the operation of the trains, and in particular when the train
must remain safe at high speeds under the service design earthquake. The paper describes studies
undertaken to establish design criteria and the analysis methods to be used for the design of high
speed rail viaducts. These studies comprised non-linear analysis of the track and viaduct structure
system under the actions of temperature variation, traction and braking, and multiple input non-
linear time history analysis for the response under earthquake loading. A series of parametric studies
were undertaken and the conclusions from this work used to form the basis of a design specification.
Track-structure interaction is the transfer of the traction and braking longitudinal loads between the
track and the viaduct deck through the ballast. Ballast behaviour under these actions is non-linear
and load and temperature dependent. Typically, viaducts for high speed railways are a succession
of simply supported spans such that no rail movement joints are needed. However it is essential
that the viaduct is designed to limit the relative displacements between decks to 5mm so that
the rails are not overstressed or the ballast destabilised under the traction and braking loads. The
fundamental principles of the analysis method to calculate the relative displacements are given in
the Eurocode (UIC Code 774-3R), but use of these requires a finite element analysis modelling the
elasto-plastic friction behaviour between the track and the bridge deck. As part of Mott MacDonald’s
role in the Taiwan High Speed Rail project, studies were carried out, aimed at providing simplified
methodology for use at the detailed design stage. Existing in-house software was adapted to analyse
models comprising elastic deck and track members connected by non-linear ballast members as
shown in Figure 1. The method and results were validated, and the process was automated to
Track 2 Member
1m 1m 1m 1m
29
30 Track-Bridge Interaction on High-Speed Railways
analyse as many structures as possible in the time available. A parametric study was then conducted
to determine the key factors affecting track-structure performance, and to develop the simplified
method of analysis.
Nearly 800 non-linear models, each with 25 viaduct spans, were created and analysed. Analysis
was carried out in two stages. In the first stage, seasonal temperature expansion or contraction was
applied to the viaduct with the train absent. Loads in the ballast members were extracted from this
model and used to provide the starting position for the second stage analysis with the vertical load
of the train and traction/braking loading. The ballast stiffnesses used, and examples of the viaduct
models analysed are shown in Figure 2. Models with pier heights from 8 m to 25 m were analysed.
All the piers had the same cross section and the same foundation stiffness, and by converting pier
heights to equivalent substructure stiffnesses, it was possible to express the geometric relationship
between the taller piers and the standard piers in a dimensionless form. By determining the stiffness
ratio of the taller piers to the standard piers at which the 5 mm limit on relative displacement between
decks was reached, a series of design charts were produced as shown in Figure 3.
(Loaded)
Ballast Stiffness
Rectangular valley
V-shaped valley
(Unloaded)
Displacement
0
n increasing →
1
Stiffness Ratio of Feature Stiffnesses, R/S
0.1
2
0.2
4
0.3
6
0.4
10
0.5
0.6
0.7
0.8
Rectangular Valley Design Lines
0.9
1
30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300
High speed rail systems in seismic zones are commonly designed against two levels of design
seismic event – the service earthquake and the ultimate (or no collapse) earthquake. The aim is to
ensure safe running during low return period events and the avoidance of collapse during events
with a suitably low chance of occurrence during the design life of the system. The Taiwan High
Speed Rail project, located in one of the most seismically active areas in the world, adopted this
approach. The viaducts are designed to resist without collapse seismic forces arising from design
peak ground accelerations up to 0.4 g, and to remain fully serviceable under a PGA of one third of
this. To ensure that trains on the viaduct can brake safely to a stop from full design speed during
service event earthquakes, track displacements must remain within the allowable values with the
structure subjected to dead load, temperature variation, train braking load, and seismic excitation.
In the main, track-structure interaction is concerned with relative longitudinal movements of
adjacent viaduct spans at the structure’s movement joints (usually over supports) and the requirement
is to prevent buckling, fracture or excessive displacement of the rails. Relative transverse movement
of adjacent spans is usually restrained by seismic shear keys or buffers on the piers that allow only
minimal movements at joints (of the order of 2–3 mm). However, examples exist where the designer
has chosen a form of construction comprising a series of contiguous portal frames, and this form
of articulation permits relative transverse movements that are several times larger than normal.
Clearly, the magnitude of these movements also needs to be controlled in order to ensure running
safety in an earthquake.
For long structures, spatial variations in seismic ground motions can be significant even for uni-
form site conditions due to complex mechanisms such as wave passage, scattering, and attenuation
effects. Hence non-linear time history analysis was adopted, and three orthogonal displacement
time histories were generated at each support location to match the seismic design spectra and
statistical spatial coherency functions.
Since the track displacement is a function of both vertical load and loading history, a series
of three-dimensional non-linear finite element analyses were performed simulating the loading
sequence. Dead load was applied to the structure first without the presence of rail or ballast
elements.
Rail and ballast elements were then “birthed” and temperature variation was applied to the gird-
ers. Following ballast property modifications to account for train vertical loading, train braking
loads were imposed on the structure and the structure was subjected to earthquake ground displace-
ments. Relative movements at the track centrelines and the forces in the rails were recovered for
assessment of track/structure performance, the key parameter being a limit on relative displacement
between decks of 25 mm.
The computer program ADINA was used. Figures 4 and 5 show the finite element modelling to
represent the viaduct. Beam elements represent the bridge deck, columns and rails; contact surfaces
with friction simulate ptfe sliding bearings at the free ends of the box girders at the connection
to the column; non-linear plastic truss elements simulate the ballast in the longitudinal direction;
and rigid links and stiff springs the interconnection of these components. The pile cap is modelled
as a rigid system between the base of each column and the soil, with the mass lumped at the pile
cap’s centre. The soil-structure interaction matrix forms the interface between the underside of the
pile cap and the ground such that the supporting soil nodes are the boundaries of the model and
represent the free-field ground in the vicinity of each foundation. The free-field ground motions
are applied to the boundaries of the model, across the soil structure interaction matrices, and these
displacements subject the structure to the seismic excitation. The free-field ground is assumed to
move with a displacement history that is unaffected by the presence of the structure.
Two viaduct models were analysed, each consisting of 25 identical spans, 30m long as shown
in Figure 6. The uniform model represents a typical viaduct crossing flat terrain with uniform pier
heights of 10 m and a pier cross section 2.7 m square, and the valley model a crossing over a gentle
valley with pier heights varying from 10 m to 18 m. For each configuration, the 25 spans represent
part of a viaduct that could be many kilometres in length. The 750 m length of the viaduct model is
32 Track-Bridge Interaction on High-Speed Railways
Rail
Deck girder
Pier
Pile
cap
Centroid of Deck
Deck Node
12x12 Pile
Stiffness Matrix
u(t) - Displacement
Mass of Time History Input
Pile Cap Ground Node
Rigid
Link
able to accommodate the 300 m long train with the train located sufficiently far from the boundaries
of the model, such that boundary effects are negligible.
The static and dynamic loads were imposed on the structure in the following sequence. First,
a non-linear static analysis was performed for dead load and temperature through an incremental
load step solution procedure using the full Newton method for equilibrium iterations.
The temperature rise was applied to the deck concrete box girders only. Next, longitudinal
and vertical loads were applied statically to one of the two tracks to simulate the train braking at
Controlling track-structure interaction in seismic conditions 33
Uniform Model
Valley Model
the onset of the seismic event. The vertical load is the weight of the train and the braking force
is a uniformly distributed longitudinal load over a 300 m long segment of the viaduct between
Piers 7 and 17. Finally, a multiple support input non-linear dynamic analysis was performed for
28 seconds of seismic load using a step-by-step direct time integration method. The Newmark
method, an implicit finite difference solution scheme, was employed to solve the problem in the
time domain with time increments of 0.01 second. For each time step, the full Newton method was
used for the equilibrium iterations.
The initial studies showed that with the proposed viaduct configuration and structural geometries,
except for sections of viaduct with tall relatively slender piers, track structure performance would
be within the 25 mm limit for relative displacement between decks. This relative displacement is
the aggregated effect at the track centreline of longitudinal movement due to braking and seismic
motions, beam end rotation under vertical load, and angular bending in plan due to transverse
seismic motions. However the information obtained was insufficient to develop usable criteria
for simplifying the design process. In subsequent studies, a series of simplified analyses were
conducted to examine the sensitivity of the structural response to various simplifying assumptions.
Simpler modelling of the coupling between decks through the track ballast system was seen as
particularly desirable, and hence a number of linear response spectrum and time history analyses
were undertaken. Results from single versus multiple support excitations, linear versus non-linear
ballast and bearing behaviour, and use of response spectrum versus time history analyses on the
response of both models were studied in detail. Comparisons of the responses of the valley model
using response spectrum, linear and non-linear time history analysis are presented in Figure 7.
Generally, the responses obtained from linear time history analysis (both multi- and single-
support excitation) and the response spectrum analysis (constraint nodes method) are equivalent,
whereas those from response spectrum analysis (absolute sum method) are almost always over-
predicted by a large margin. The maximum relative displacement from the nonlinear analysis is
about 20 mm, compared with 65–70 mm from the linear analyses. Thus it appears that there is
considerable benefit to be obtained from modelling the nonlinear behaviour of the ballast in a track
structure interaction analysis for earthquake loading.
The results from the parametric studies described above provided confidence that outline designs
prepared using simplified methods are feasible and could be developed to meet detailed contract
requirements. Designers should nevertheless be required to carry out full track-structure analyses
for the service level earthquake case for all sections of viaduct, during the detailed design phase.
It was clear from the studies that nonlinear time history analysis would be required in order to
obtain sufficient accuracy in the predictions of relative displacements of adjacent spans. However,
it was considered that there was a relatively small difference between applying a synchronous time
history excitation input to each pier and including wave passage effects by applying time delayed
displacements as inputs to each pier. Following another study, it was concluded that the additional
effect of spatial variation could be adequately represented by adding a relative displacement that is
a direct function of span length. This displacement modifies (increases) the value of displacement
obtained by applying synchronous time history input. The value is around 2.5 mm for 30 m spans.
34 Track-Bridge Interaction on High-Speed Railways
140
Relative Displacement (mm)
120
100
80
60
40
20
0
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Pier No.
The majority of the designers for the THSR Project carried out the track-structure interaction
analysis solely on the basis of the non-linear time history method, including the coupling effects of
the track. However, several of the designers also presented results of analyses using linear response
spectrum methods without track. In addition, the authors’ firm, as Independent Checking Engineer,
carried out a number of check analyses using a variety of methods. It has therefore been possible
to make some comparisons between the results.
Using the linear response spectrum method, disregarding the track, the relative longitudinal
displacements at joints under earthquake are generally in the range 15 to 40 mm, but in some
cases as high as 60 mm. Using the non-linear time history method, including the track, the relative
displacements under earthquake were always found to reduce to values comfortably within the
specification limit. Indeed, the maximum displacement calculated by any of the designers or by
the Independent Checking Engineer for the standard viaducts is around 12 mm (worst case with
highly non-uniform stiffnesses with adjacent piers). Typical values with reasonably consistent pier
top stiffnesses are around 5 mm. These results are in good agreement with the pre-project work
described in Sections 1 and 2 of this paper.
The THSR Design Specification limits rail stresses to 167 MPa in tension and 147 MPa in com-
pression, values that are considered to provide an acceptable margin of safety against either fracture
or buckling. The rail stress can only be reliably checked by means of a non-linear time history anal-
ysis, with the non-linear connections between the rails and the structure properly modelled. The
designers were provided with bilinear (elastic/plastic) stiffness relationships for the trackwork for
use in their models, as shown in Figure 2. The designers have generally reported rail stresses from
their analyses that are comfortably within the specification limits – commonly up to a maximum
of 100 MPa. The checks carried out by the Independent Checking Engineer have revealed similar
results.
Controlling track-structure interaction in seismic conditions 35
4 CONCLUSIONS
From pre-project studies, confirmed by reviews and checks of the actual designs for a major high
speed rail project, it is clear that unless the appropriate track-structure interaction analysis methods
are adopted the displacements at structure joints can be over-estimated, and that this could lead to
uneconomic design.
It is essential to perform a track-structure interaction analysis based on non-linear modelling
incorporating the coupling between the track and the viaduct decks, and using appropriate acceler-
ation time histories as ground motion input. The stiffness of the foundation must be included in the
model, although the response of the structure itself often dominates the displacements at deck level,
particularly for high piers. A key requirement is to model as accurately as possible the non-linear
interface between the track and the structure, in order to derive peak rail stresses in addition to the
relative displacements between viaduct spans at structure movement joints.
Using the above approach, it has been found that the relative longitudinal displacements between
viaduct spans remain comfortably within the limit specified. Similarly, peak rail stresses are gener-
ally well below the limits required to provide a margin of safety against either fracture or buckling.
Typically, for “service” level PGAs of up to 0.13 g, peak relative displacements are of the order of
12 mm and peak rail stresses in the range 80–100 MPa. Nevertheless, a minimum level of structure
stiffness is necessary to achieve compliance with the requirements and large variations in stiffness
between adjacent piers are to be avoided.
ACKNOWLEDGEMENTS
The permission of the Taiwan High Speed Rail Corporation (THSRC) to publish technical
information on this project is gratefully acknowledged.
The Independent Checking Engineer for the THSR Project was IREG (International Railway
Engineering Group), a Joint Venture of DE-Consult, Electrowatt Engineering, Mott MacDonald
and SYSTRA.
REFERENCES
“Track-Structure Interaction on the Taiwan High Speed Rail Viaducts”, Place, J.D., Davis, S.G. and Barron, M.
Paper presented at the IABSE Symposium ‘Structures for High Speed Railway Transportation’, Antwerp,
August 2003.
“Bridges for High Speed Railways – Special Considerations”, Davis, S.G. and Wilkins, A.G. Paper presented
at the Institution of Civil Engineers Conference ‘Current and Future Trends in Bridge Design, Construction
and Maintenance’, Kuala Lumpur, October 2005.
CHAPTER 5
F. Millanes Mato
Universidad Politécnica de Madrid & IDEAM S.A., Madrid, Spain
M. Ortega Cornejo
IDEAM S.A., Madrid, Spain
ABSTRACT: This paper describes the specific problems concerning the design and dimensioning
of the bearing systems for some viaducts of the Ankara-Istanbul HSRL. These structures, with
total lengths of up to 2232 m, consist of a series of simply supported 34-meter-long spans, whose
cross-section is constituted by a deck with multiple precast I-beams, transversely braced at their
ends.
Because of the area’s high seismic activity, with ground accelerations of up to 0,21·g, the
structure’s design turned out to be highly conditioned by the global seismic structural response. In
addition to the classical deck-piers-foundation interaction, it proved essential to take into account
the problems dealing with the rail-structure interaction as well as the bearings’ design, strength and
ductility. These considerations led to technically innovative dispositions for the aforesaid bearings.
1 INTRODUCTION
As part of the High Speed Railway Line Ankara-Istanbul Rehabilitation Project, IDEAM, S.A. has
collaborated with Eng. Manuel Alpañés OHL’s Technical Office Director, in the execution project
for the structures of Viaduct 1 and 4 with 1032,80 m and 2232,45 m length respectively, built by
the Contractors OHL/Alarko/G&O Joint Venture.
Dr. Eng. Juan Carlos Lancha of OHL’s Technical Office has also collaborated with IDEAM,
S.A. in the multimodal seismic analysis of the Viaducts.
The new High Speed Railway Line has been projected for a speed of 250 km/h.
According to the client, the deck of both Viaducts should consist of precast prestressed double-T
deck beams placed in contact with each other (to eliminate the need for slabs with permanent
shuttering) and cast in place concrete slab.
In order to fulfil precasting and transportation requirements, the maximum span should not be
greater than 35 m.
Viaduct 4 is the longest viaduct of the Ankara-Istanbul High Speed Railway Line with 2.232,45 m
long, and the deck consists of 66 simply-supported spans distributed as follows in the viaduct
(Figs 1 and 2):
– First span with 23,40 meters between the axis of bearings at abutment and axis of pier 1.
– 64 typical spans with 34,00 meters between centrelines of adjacent piers.
– Last span with 33,05 meters between the centreline of pier 65 and the axis of bearings at
abutment 2.
37
38 Track-Bridge Interaction on High-Speed Railways
Figure 1. View of Viaduct 4 during construction. Figure 2. Lateral View of Viaduct 4 concluded.
According to the client, the bridge-deck cross-section is made up of 12 precast prestressed beams
1,95 m deep and 0,93 m wide, abutting to each other (Fig. 3). Just 0,03 meters are kept free between
adjacent beams to allow for tolerances in the execution. Cast in place concrete compression slab is
laid over the beams, with thickness varying from 0,25 meters to 0,34 meters to obtain transversal
slope required. The width of the deck remains constant at 11,50 m.
Longitudinal displacements of the spans will be restrained in one end and allowed at the other
one. Appropriate design of the bearings system in the deck is carried out according to this condition
as described later. In these conditions expansion joints at the rails over any of the abutments will
not be required, in view of the supports layout and mentioned spans. The track-structure interaction
analysis confirms this assumption.
Lateral displacements are restrained at both ends of each span with lateral bearings between
the deck and the pier or abutment. A simple transverse bracing between the beams is designed to
achieve with transverse requirements.
All the abutments are of the closed type, which allows for an easy construction of transition
structures, as required in High Speed Railway systems.
Track-structure interaction and seismic design of the bearings system 39
Piers consist of transverse frames with two hollow prismatic shaped columns, 2,20 m wide and
3,40 m long, connected at the top with transverse cap supporting the beams. This upper element
also includes lateral restraints for the deck (Figs. 4 and 5). The high of the piers of Viaduct 4 varies
from 7,40 m to 18,03 m.
The foundations of the piers have been designed with 16 piles of 1,20 m of diameter.
Viaduct 1 is 1.032,80 m long, and the deck consists of 31 simply-supported spans distributed as
follows in the viaduct (Fig. 6):
– First span with 23,40 meters between the axis of bearings at abutment and axis of pier 1.
– 29 typical spans with 34,00 meters between centrelines of adjacent piers.
– Last span with 23,40 meters between the axis of pier 30 and the axis of bearings at abutment 2.
The main difference between Viaduct 1 and 4 is the geometry of the piers. The piers of Viaduct
1 consist of transverse frames with three cylindrical shaped columns (Fig. 7), 2,00 m diameter,
connected at the top with transverse cap supporting the beams. This upper element also includes
lateral restraints for the deck, the same way as it happened on Viaduct 4. The high of the piers of
Viaduct 1 are remarkable lower than Viaduct 4, and varies from 4,24 to 7,84 m high.
In the case of a bridge with statically determinate short spans, the thermal effects, shrinkage, creep
and bending do not introduce important displacements or stresses in the rails.
However, from the point of view of the track-structure interaction, “fixed points” in the deck
will be needed to ensure that braking loads are transferred correctly. The creation of such “fixed
40 Track-Bridge Interaction on High-Speed Railways
points” means that supports must be fixed in one direction and that the flexibility of piers and
foundation must be limited. For this reason the use of specific bearings is required, fixed in the
longitudinal direction at one end of the beams and free to slide at the other.
A specific analysis for this structure has been developed according to Eurocode 1, part 2 [1],
so as to guarantee that stiffness requirements for the substructure are fulfilled according to track
structure interaction, and no excessive displacements or stresses appear on the rails.
Track-structure interaction and seismic design of the bearings system 41
Due to the high level of seismic activity in the area, seismic criteria are especially relevant for
the design of the structure.
In general seismic design runs counter to provisions for track-structure interaction. In fact, fixed
points and rigid piers are required to assure suitable behaviour of the structure with regard to
braking/start loads. This increases the seismic loads on the piers and foundations.
Just for stability of bearings or uplift forces in the prestressed deck some checking could be
necessary according to Eurocodes, which have been the only incidence in the design from vertical
seismic action.
Seismic design forces for individual members of the bridge have been determined by dividing
the elastic forces obtained from the spectrum of Figure 8 by the appropriate “behaviour factor” q.
This factor has the same significance than the Response Modification Factor R in AASHTO.
According to the height of the piers in the longitudinal direction for the shorter pier of Viaduct
4 q = 2, 98 ≈ 3. As q = 2,98 is obtained for the shortest pier we used q = 3 for all the piers in
longitudinal direction for Viaduct 4.
This value is coincident with R = 3 established by AASHTO for single columns. So both
standards have been simultaneously fulfilled in longitudinal direction.
Meanwhile, in the transverse direction, in Viaduct 4, for piers with more than 12 m high q = 3,
and for piers with less than 12 m high (7,40 m minimum), q = 2,238.
As AASHTO establishes R = 5 for multiple column bent piers it is clear that ductile factors for
transverse direction according to Eurocodes are on the safety side from Response Modification
Factors from AASHTO.
Bearings and forces transmitted to foundations have been obtained by a plastic capacity analysis
including appropriate overstrength factors according to Eurocodes, as required by the client.
Equivalent linear analysis has been adopted for all elements, including ductile components
as piers.
For the estimation of element stiffness, stiffness values corresponding to uncracked cross-section,
or effective values after cracking, can be used.
As an overestimation of the stiffness leads to results which are on the safety side regarding the
seismic actions, uncracked stiffness have been used in the calculations of seismic forces.
This assumption is not true in the case of displacements, and calculations with effective stiffness
after cracking is made in the case of ductile components (piers) so as to obtain safety values for
displacements.
Rigid deck behaviour is considered, taking into account that the deformations of the deck are
negligible compared to the displacements of the substructure elements.
Piers and abutments are assumed to be fixed to the soil foundation when evaluating seismic
forces, and no soil-structure effects has been considered. However, flexibility of the foundation has
been considered according to geotechnical parameters of the ground included in the geotechnical
report to obtain seismic displacements.
Mean values of permanent masses (self-weight of deck, piers and abutments, and dead loads)
have been used. Null quasi-permanent values of the masses corresponding to variable actions have
been considered, in the event of normal traffic intensity on the line, according to Eurocodes (ENV
1998-2:1994 [3] and prEN1998-2. Draft April 2004 [4]).
The elastic forces and displacements shall be determined independently along two perpendicular
axes, longitudinal, and transversal.
As there are no interactions between decks in the longitudinal direction (due to the fixed-sliding
bearings system) (Fig. 9), a single degree of freedom model is appropriate for modelling the
behaviour of the structure in longitudinal direction.
A single mode spectral analysis has been used. The equivalent static seismic forces from deck on
abutments and piers in the longitudinal direction are derived from the inertia forces corresponding
to the fundamental natural period of the structure (abutment or pier and one span of the deck) in
that direction, using the relevant ordinate of the response spectrum.
Fi = MiSd(Ti) (1)
Where:
– Mi is the effective mass attributed to the abutment or the pier “i”, which corresponds to the mass
of one span.
– Ti is the fundamental period of the same element (abutment or pier).
From the safety side inertia forces from the own mass of piers have been considered with
the same seismic spectral acceleration. However, inertia forces from the own mass of the abut-
ments is expected not to be significantly amplified and seismic ground acceleration have been
considered.
As there are few interactions between decks in the transverse direction, a single degree of freedom
model could be appropriate enough for modelling the behaviour of the structure in that direction.
A single mode spectral analysis also has been used in the transverse direction. The same way,
the equivalent static seismic forces from deck on abutments and piers in the transverse direction
are derived from the inertia forces corresponding to the fundamental natural period of the structure
(abutment or pier and one span of the deck) in that direction, using the relevant ordinate of the
response spectrum.
As it was made for the longitudinal analysis, from the safety side, inertia forces from the own
mass of piers have been considered with the same seismic spectral acceleration. However, inertia
forces from the own mass of the abutments is expected not to be significantly amplified and seismic
ground acceleration have also been considered.
Conclusions from the transversal single degree of freedom model are confirmed by additional
multimodal analysis of the structure. Transverse seismic forces from multimodal analysis confirmed
the values obtained with the single degree of freedom model as described later.
Interaction between adjacent decks from out of phase transverse displacements of piers is also
obtained with multimodal analysis, which has been used for the design of bearings.
The design forces for piers have been calculated by dividing the elastic forces, obtained as
explained before, by the appropriate behaviour factor q.
It has been done a Plastic Capacity analysis according to Eurocodes to obtain the design forces
for bearings and foundations of piers, and the smaller of these results or the elastic forces have
been considered in the design.
Figure 10. Transversal reactions on piers obtained from the multimodal analysis.
Figure 11. Longitudinal forces in the 4 central bearings due to a vertical moment.
To evaluate with more accuracy the efforts in the 4 longitudinally fixed bearings (Fig. 12), we
took the vertical moment reaction obtained from the second model. This moment is equivalent to
a longitudinal distribution of forces with the following results (Fig. 11):
– in twenty nine piers and in the abutment AB2 the maximum force in one bearing reached a value
greater than 3000 kN.
46 Track-Bridge Interaction on High-Speed Railways
– in eighteen of these piers and in the abutment AB1 this value is greater than 4000 kN
– in eleven piers this value is greater than 5000 KN. The maximum value obtained is 13270 kN, in
pier number twenty three.
– In thirty six piers this force is less than 300 t.
Figure 14. Detail of cast in place concrete blocks between the inferior heads of the beams.
The serviceability conditions required from the bearings system are shown in the project’s plans,
and present some specific requirements in its response to the important horizontal loads acting on
the bridge, chiefly braking and seismic actions.
The project’s specifications can be met by means of a certain variety of solutions, each one of
them employing different technologies.
Figure 15. Frontal view of cast in place concrete blocks between the inferior heads of the beams.
The horizontal transverse forces are resisted by means of 4 lateral bearings placed at the corners
of the pier’s head. (Figs 18 and 19)
Figure 13 shows the cross section of the deck in the support line. In both ends, the inferior heads
of the beams are joined together at the same level of the lateral bearings with cast in place concrete
blocks (Figs. 14 and 15), for transmitting the horizontal reaction of the deck to the lateral bearings
of the piers.
The project allows for the design of the 24 bearings employing either neoprene or POT-type
devices.
If neoprene bearings are used, their disposition would be as follows (Fig. 12):
– 12 elastomeric sliding bearings at the end of each span (left side of the pier).
– 4 elastomeric unidirectional bearings, free in the transverse direction, located at the beginning
of the 4 central beams (right side of the piers) in order to withstand the longitudinal horizontal
forces.
– 8 elastomeric bearings placed at the beginning of the span (4 at each side of the deck).
In the case of using POT-type bearings, their arrangement would result in:
– 20 free Pot bearings (Fig. 21), 12 of them located at the end of each span (left side of the pier)
(Fig. 22), and 8 at the beginning of the span (4 at each side of the deck).
– 4 unidirectional POT bearings, free in the transverse direction, placed at the beginning of the
4 central beams. (Fig. 23)
However, both options are mutually exclusive. It is not possible to use elastomeric bearings and
POT-type devices simultaneously, neither in the same line of supports nor in different lines. The
difference in the stiffness of these devices renders them incompatible in the bridge, irrespective of
their location.
Track-structure interaction and seismic design of the bearings system 49
On the other hand, the lateral bearings must be elastomeric, standard type at the beginning of
the span (right side of the pier), and sliding type for those at the end (left side of the pier). (Figs 18,
19 and 20)
In addition to absorbing the vertical and horizontal forces as well as the design displacements,
there are two basic conditions to be observed in the bearing’s design.
a) Distribution of the horizontal longitudinal force among the 4 transversely oriented central
bearings.
The horizontal longitudinal forces must be withstood by the set of the 4 central transversely
oriented bearings. The force criterion is established according to the total force to be resisted by
the 4 bearings, instead of that resisted by each individual element. It is the provider’s responsibility
to appropriately distribute that total force among the 4 bearings according to the system’s own
characteristics.
Along these lines, it is necessary to observe EN 1337-1:2000 [5] in order to account for the
possible undesirable incidence on each support’s loading state caused by an adverse distribution of
the execution tolerances and gaps between the bearing device’s elements responsible for transmitting
the horizontal actions.
Track-structure interaction and seismic design of the bearings system 51
Figure 22. View of the free sliding POT-bearing. Figure 23. View of the four central unidirectional
POT-bearings.
In the case of using elements of high stiffness and little ductility in order to transmit the horizontal
forces, as it is usual in POT-type bearings and in the guiding slots of oriented neoprene bearings,
the gaps and execution tolerances, even within the range admitted by the legislation, may very
significantly alter the actions distribution in the central supports with respect to a hypothetic
uniform share. The system’s inability to offer a ductile enough response, and therefore to regularise
the loads on the supports, may lead to failure without previous warning.
For this reason, and since the acceptable actions distribution on the bearings depends basically
on the chosen system’s intrinsic characteristics, it proved advisable, in the project stage, to specify
in the plans the total force to be resisted by the system, leaving the proper forces distribution to the
provider’s know-how according to the eventually implemented system’s features.
b) Stiffness in service conditions and displacement capability under sustained load caused by
the seismic action.
The 4 central bearings which transmit the horizontal longitudinal forces must display a rigid
response under service conditions (braking and start forces), but it is necessary to allow for a
±10 mm displacement capability (with respect to the initial position) under the seismic action,
without exceeding the maximum seismic longitudinal force shown in the plans.
The bearing’s displacement limitation under maximum load is necessary to dissipate/release
the effects caused by an offset in the pier’s transverse displacement when subjected to transverse
seism. The vertical axis torsion thus induced on the deck, added to the torsional stiffness of the
frames that constitute the piers, would introduce great longitudinal forces in the oriented bearings
if they were rigid, as it is required under serviceability conditions. This is why it is necessary to
relax this rigid response under service loads when it comes to evaluating the seismic response,
letting the bearings absorb the rotation around the vertical axis by developing admissible stresses.
A longitudinal displacement of ±10 mm without exceeding the maximum longitudinal seismic
action (as specified in the project) is enough to eradicate the incidence of transverse piers offset
under transverse seismic action.
This displacement capability under seismic action leads to a very favorable consequence in the
design stage: the distribution of the longitudinal seismic forces can be assumed as uniform for the
4 bearings, since the system has the displacement capability to regularise the forces acting on each
of them. The aforesaid concern about the distribution of the horizontal longitudinal forces, and
the incidence of the bearing’s execution tolerances and gaps on that share, is therefore limited to
service loads and not to seismic actions (with slightly higher values).
– Those based on sacrifice shear locks which materialise the transition from a rigid response
(service) to the allowance for a ±10 mm displacement under seismic action.
– Those which attempt to materialise a hinge allowing the relative rotation of the deck with respect
to the piers, essential in order to release the effects caused by the pier’s transverse offset when
subjected to transverse seism.
– Those using dissipative antiseismic devices also implementing impact transmission functions,
which provide with the necessary stiffness under service conditions.
– Those implementing pre-compressed neoprene in order to achieve the described type of response.
(Fig. 24)
This bearings system ensures an adequate response to the two basic, previously described,
requirements.
On the one hand, the suggested system adequately displays a rigid response under service
conditions and, on the other, allows for a relative displacement of ±10 mm when subjected to the
maximum design seism.
This kind of bearings can be assumed to distribute longitudinal loads uniformly among the four
central members. Even assuming the existence of a non-favourable execution tolerances distribution
in those elements responsible for transmitting longitudinal actions – which would lead to an overload
in one bearing with respect to the others–, the system’s response is guaranteed. The load would
be directed towards the most penalised bearing –that with the worst tolerance condition – until
it reached the rubber precompression force. But after that, it would suffice with a displacement
within the POT guaranteed tolerance range – millimetric – to cause the adjacent bearings to be put
in load until balancing the applied load, without further complication in the system’s behaviour.
That is to say, the system’s flexibility necessary to regularise the incidence of execution tolerances
on the POT guides is guaranteed, neither hampering the system’s global response, nor causing a
risk of overloading which might lead to premature failure under service loads.
Overall, this bearings alternative provides an adequate response to the design requirements.
It also presents some additional convenient features, such as:
– Absence of fusible elements on which the stiffness change between the service and seism
situations depends.
– It does not contain fatigue-sensitive elements, which might either unleash premature failure or
require over dimensioning to avoid it.
– Easily inspection, maintenance, and replacement, even periodic or after an important seism.
The precompressed rubber solution allows us to satisfactorily meet the design requirements,
therefore being the eventually chosen alternative.
REFERENCES
Track structure interactions for the Taiwan High Speed Rail project
D. Fitzwilliam
TY Lin International, San Diego, CA, USA
ABSTRACT: This paper describes the analyses for one of the special structures of the Taiwan
High Speed Rail project. These analyses addressed the rail-structure interaction of a ballast track
portion of the alignment subjected to a train braking load and a seismic load. Results for a response
spectrum analysis and a nonlinear time history analysis are presented. Advantages and limitations
of the two methods are discussed.
1 INTRODUCTION
The Taiwan High Speed Rail project consists of over 26 kilometres of viaducts and bridges, crossing
Taiwan from north to south for nearly the entire length of the island. Structures on the project were
analyzed for two types of earthquakes: Type 1 (severe) and Type II (moderate). Repairable damage
in the inelastic range is expected for a Type I earthquake based on capacity design. The structure
is designed for safe operation at maximum speed with no yielding under a Type II earthquake.
Relative gap displacements across structure movement joints and rail stresses were computed for
the rail-structure interaction analysis, using dynamic time history analysis and response spectrum
analysis. For Type II earthquakes, the dynamic analysis included dead weight of the structure and
train, braking, temperature expansion or contraction, and ground motion applied at the foundations.
2 BACKGROUND
With the faster speeds and higher capabilities of computers, many civil engineering methods need
to be updated. Many methods that are being used today to analyze and design structures were
developed years ago. Computer technology has progressed much faster than the fields in which
they are used. It is the engineers’ responsibility to look at older methods of analysis and determine
if they were limited by the computer technology of the time. One method that may be improved by
using advanced computers is designing bridges for dynamic loadings.
Two methods are used for modelling structures subject to seismic excitations. The most common
method is response spectrum analysis. A more demanding analysis method is time history analysis.
Response spectrum analysis is useful for models with a linear elastic response to the loads being
applied to it. When nonlinear behaviour is expected, response spectrum analysis cannot provide
a direct solution without a careful iteration procedure. Time history analysis is able to directly
solve in either linear or nonlinear domains as long as the nonlinear properties of the structure
can be adequately modelled. Currently, many engineers separate structures into two main parts:
the superstructure, which is often linear; and a foundation, which is likely to be nonlinear. In the
case of this project, the nonlinear portion is the ballast connecting the rails to the deck. These two
portions are then modelled separately. The first step is to apply the earthquake or other dynamic
loading to the superstructure, which is modelled on fixed supports at the base of each pier. The
maximum reactions at the base are then found and applied to a separate model of the substructure.
55
56 Track-Bridge Interaction on High-Speed Railways
The displacements of the nonlinear substructures are found and used to compute an equivalent
stiffness to replace the fixed supports of the superstructure model. The dynamic loading is again
applied to the modified structure and new base reactions are found. The process is repeated until it
converges on reactions and displacements that correspond in both the superstructure model and the
substructure model. The internal forces in the two models are then used in the design and further
analysis of the bridge.
The procedure is similar whether the nonlinear portion is in the foundation or in any other element
of the structure. In the design of rail bridges, consideration must be given to the method in which
the rails are connected to the deck. If connection of the rails is done either with direct fixation
or by using ballast, forces applied by trains to the rails are transmitted to the structure through
elements, which are likely to respond with nonlinear behaviour. Similarly, forces transmitted from
the structure to the rails, such as those resulting from seismic movements, must also pass through
these nonlinear elements.
3 PROJECT DESCRIPTION
The Taiwan High Speed Rail project consists of over 26 kilometres of viaducts and bridges, crossing
the Erh Jen and Ah Kung Tien rivers and includes a 420-meter long, four-track structure through
Taiwan Station. Spans vary in length from 15 to 45 meters. The typical superstructure width for
the twin track box girder is 13 meters. Tracks centers are typically placed at a distance of 2.25
meters to either side of the center line of the box girder (Fig. 1). The box girder superstructure is
constructed on twin wall columns (Photo 1) in a high seismic region using a travelling false work
system that enables casting one complete span at a time.
This paper describes the structure on Contract 295, which consists of 27 km of elevated viaduct
and one station. The typical structure is composed of cast-in-place concrete post-tensioned box
girders built monolithic with twin pier walls. Continuous structures are used in track switching
areas, the longest being 150 m. On these structures, the end piers provide support through bearings
to reduce the demands on the pier walls and foundation. These piers also have shear keys and lock
up devices, which engage under earthquake and braking loads.
Figure 2. Analysis model showing three single span units and one three span continuous unit.
58 Track-Bridge Interaction on High-Speed Railways
Stiffness (kN/m/track)
Stiffness (kN/m/track)
80 curve Expected
Loaded curve 50 curve
60
40
Load state after
40 30 temperature
Unloaded curve Unloaded
20 20
curve
0 10
0 1 2 3 4 5 0
Load state after 0 1 2 3 4 5
disp (mm) train + braking disp (mm)
Figure 3. Nonlinear ballast spring behavior includ- Figure 4. Nonlinear ballast spring behavior includ-
ing temperature loads. ing braking loads.
3.2.3 Rails
Rails were included explicitly in the Type II time history analyses. A rail similar to the standard
AREA 57 kg/m was assumed with a cross-sectional area of 72.65 mm2 .
Figure 6. Forces in rails loaded with the weight of one train and braking force.
was included on the entire length of the structure, at one set of train nodes. Also, one train engine
was assumed centered.
3.2.5 Piers
The Piers are modeled with cracked section properties for the track-structure interaction analysis,
with section inertias reduced to 70 % of their gross values.
Figure 7. Maximum tension forces in rails during time history analysis of Earthquake Type II.
length of the model (i.e., the angle between the direction of travel of the wave front and the structure
centerline is zero.)For the Type II rail-structure time history analysis, the ballast truss elements must
be preloaded by the dead load of the train and structure with the unloaded properties. After that, the
loaded properties must be used for those tracks that carry trains during the analysis. The following
procedure was used to accomplish this. First, the dead load and the train load was applied using
the unloaded ballast properties. The loading condition of each ballast truss element was examined,
and a new nonlinear material was generated with the same condition at the end of the dead load as
at the first point (assuming the response was elastic). The loaded properties started from that point
(Fig. 5). The new nonlinear properties were input into the model, and the dynamic time history
analysis was started again with the dead load and train load included. Spring properties used in the
nonlinear models can be seen in Figures 3 and 4. A time step of 0.01 seconds is used, so frequencies
up to about 50 Hertz are accounted for in the analysis. Damping as specified to be 5 percent for
all vibration modes. In a time history analysis, Rayleigh damping is used whereby two particular
frequencies can be damped 5 percent exactly, but other modes will have different damping. An
assumption of 5 percent damping for periods of 0.1 and 2.0 seconds was deemed appropriate to
approximate a result of overall 5 percent damping. For horizontal modes, no significant modes are
below 0.1 seconds, so the model is slightly under damped. For the vertical direction, most of the
modes occur in the region of 0.1 and 0.2 seconds, so the damping is approximately 5 percent.
4 CONCLUSIONS
The forces shown in Figure 7 indicate that the rail reaches a maximum tension at an expansion joint.
The shape of the tension diagram indicates the spans on opposite sides of the expansion joint are
moving toward one another and the ballast spring elements are in the nonlinear range. The diagram
shows the force increasing from zero to 2200 kN, a length of just over 35 m. This corresponds to the
60 kN/m limit for the ballast springs shown in Figures 3 and 4. The diagrams also indicate that the
extent of the slipping in the ballast is confined to approximately one span at the time step shown. In
order to model the same behavior in a response spectrum analysis, the location, state and number
of nonlinear elements must be known before running the analysis. This is at best a guess in the
initial system and the effects of the initial guess can greatly influence the results of the analysis. In
Track structure interactions for the Taiwan High Speed Rail project 61
this way, the designer is tempted to produce the desired results by adjusting the initial guess until
the result is within the allowable range.
The response spectrum analysis was performed as a preliminary indicator to evaluate if the more
sophisticated and complex time history analyses were required. The results of the comparison show
that the nonlinear nature of the rail-structure interaction makes time history analysis indispensable
whenever there is concern about the stresses and deformations of the rail or box girders. With
computer capacities and processor speeds of today, the time history analysis should no longer be
avoided in favor of a response spectrum analysis when nonlinear behavior is expected.
REFERENCE
Taiwan High Speed Rail Corporation, Taiwan High Speed Rail Design Specifications, Vol. 9. 21 January, 1999.
CHAPTER 7
ABSTRACT: The communication deals with the SNCF experience of track-bridge interaction.
Following items will be successively treated:
– long welded rails: conception, design and current effects on platform
– bridges as singular points in the current platform
– behaviour of the attach from the track on the bridge deck
– dimensioning of structures including track-bridge interaction, preliminary approach and f.e.m.
calculation
– associated equipment (joints and dilatation devices)
– conception of structure in order to manage the phenomenon
– examples of good practices in terms of general design for structures submitted to track-bridge
interaction.
1.1 Generalities
In France, since 30 or 40 years old, all new tracks have been designed with long welded rails.
This evolution was necessary to:
– improve the comfort of the passengers
– increase the speed of the trains (>120 km/h).
Nevertheless, long welded rails have only been enabled by recent technical progresses, such as:
– the availability of very high strength steels (fe > 900 MPa) and the progress in welding techniques
– the development of modern and reliable track equipments: concrete sleepers, modern connection
between rails and sleepers, ballast, . . .
63
64 Track-Bridge Interaction on High-Speed Railways
< 150 m
< 150 m
E.A.␣.⌬Tr
Along the tracks, other special sections may appear where additional effects may have influence
on the track:
– Each interruption of the LWR (switches, . . .)
– bridges (= deformable platform . . .),
– end of tunnels (discontinuity of exposure . . .)
In some cases, where stresses may be too high, rails have to be cut and special Track Dilatation
Devices have to be implemented.
Track-bridge interaction – the SNCF experience 65
2.1 Generalities
When LWR cross bridges:
– loads that are applied to the track (train. . .) are (partially) transmitted to the deck.
– imposed deformations of the bridge induce additional stresses in rails.
That is the reason why engineers speak about interaction.
αF
To guaranty security, it must be controlled that the total longitudinal force in the track (self
behaviour + influence of the bridges), including second order effects will not lead to lateral buckling
of the rails, or excessive slipping in the ballast.
As a simplification, the global longitudinal resistance is assumed to be divided in two parts:
– one part is reserved to current track behaviour
– the other part is available for additional effects due to the bridge
This approach represents a simplification of the reality, in order to be able to study the bridge
effects apart from the current behaviour. It is a conservative approach.
F = Ku1 = f (x)dx = −F2 − F1 ; u2 − u1 = α LT (1)
As instance, for a simply supported span, the general shape of the longitudinal force in the rails is:
Frail
F1 F2
f(x)
⌬T
F
K
u1 u2
Frail
F1 Fb F2
f(x)
F
K
u u
As instance, for a simply supported span, the general shape of the the longitudinal force in the
rails is:
Frail
Fv
F1 F2
f(x)
θ h
To approach the track/bridge interaction a f.e.m. calculation may in many cases be performed.
Main characteristics of the model are following:
– bridge + pears + foundations are represented by beam/plates elements
– rails are introduced in the model by additional beams (with at least 100 m at each abutment)
– the connection between rail and deck is described by non linear elements (representing the
sleepers and the ballast)
Rail
platform bridge
Rail u(x)
f(x)
f f(x)
v(x)
Figure 10. Behaviour for the connexion between the track and the deck.
Nevertheless, to simplify the analysis, the function f (x) is usually assumed to be of bilinear type.
Two different domains can be identified: linear elastic domain and pure friction domain.
f f
loaded track loaded track
60 kN/m 60 kN/m
unloaded track
40 kN/m
unloaded track
20 kN/m
Rail
platformt K bridge
Step 1: application of a fraction α1 T on the elastic model, until “plastification” of the first
connexion element i1 .
The contact force in each (elastic) contact element is fi,1 : fi,1 = 20 kN/m (unloaded ballasted
track)
Boarder of the
elastic domain
elastic domain
Element i1
Boarder of the
elastic domain
Element i1
Element i2
3.3 Standards
Following standards are applicable:
(In case of succession of independent decks, δB and δH are the relative displacements between two
consecutive decks)
Additional stresses in rails σ < 72 MPa in compression; σ < 92 MPa in traction (for ballasted
track equipped with rails type UIC 60 . . .)
66 m
45 m
abscisses
des joints 77 143 209 275 341 407
abscisses
des appuis 77 132 198 264 330 396 451
30
30
25
20
10 15
0 10
0 66 132 198 264 330 396 462 528
5
-10
0
-20 0 66 132 198 264 330 396 462 528
-5
-30 -10
-40 -15
abscisse (m) abscisse (m)
Temperature ∆T = 35ºK Braking/acceleration on central spam
L L1 L2
Standards give all necessary indications to calculate the effect of track/bridge interaction, but it is
not enough to perform a valuable design of the bridges.
If the additional stresses in rails exceed codes limits, or if the total dilatable length is greater
than 90 m (concrete and composite bridges) or 60 m (steel bridges), LWR must be cut and Track
Dilatation Devices (TTD) must be installed.
Nevertheless, LWR must be as long as possible (for maintenance), and bridge engineers have to
take this recommendation into account.
– For TDD, the track can not be simultaneously curved in plan and in elevation.
– The maximum dilatable lengths consistent with the greatest track dilatation devices in France
are about 450 m.
In addition to Track Dilatation Devices it is necessary to put special expansion joints, that are
able to retain ballast.
fixed bearing
mobile bearing
retaining ballast expansion joint
This solution has been applied on several viaducts like “Haute Colme” and “Avignon”.
L < 90 m (usually 30 to 40 m)
L < 90 m
5 CONCLUSIONS
The experience of the SNCF in track-bridge interaction has begun with the construction of the
new high-speed lines (1975–1980). Nowadays this part of the design of bridges is well known. It
remains a field where solutions must be found in relation with track experts and people in charge
with the maintenance. The temptation is high to design systems that are complex and expensive in
terms of maintenance.
REFERENCES
ABSTRACT: Some experiences and studies on the subject of track-bridge interaction in Japan are
presented. As for the problems in ordinary conditions, studies on the influence of the temperature
change between CWR and bridge girders, experiences on the vibration isolation using a newly
developed track system, and experiences on the rail extension and contraction at edges of a long
span bridge are introduced. As for the problems in seismic conditions, studies and experiences on
the vehicle’s running safety on structures, and displacement limit criteria of track and structures
are introduced with some explanation on a vehicle/track/structure interaction analysis program.
1 INTRODUCTION
Various kinds of problems are related to the track-bridge interaction. In this paper, some experiences
related to them in Japan are briefly introduced.
In the daily circumstance, one of the most popular problems may be the longitudinal force
induced from continuously welded rail (CWR) to a bridge due to the temperature change. A brief
history on the theoretical studies conducted in Japan is introduced. Next popular problem may be
the rail expansion and contraction at the edges of a long span bridge due to its deflection. From
1970s, long span road-rail bridges had been constructed to connect Honshu (Main Island) with
Shikoku Island of Japan. The problem was studied to design adequate expansion joint devices
at that time. Outlines of the bridge, the expansion joint device and the running test which was
conducted after the completion of the bridge are introduced.
Many severe earthquakes attack Japan. Therefore, not only the seismic strength of railway
structure but also the running safety of railway vehicle on the structure during an earthquake motion
is our great concern. A vehicle/track/structure dynamic interaction analysis program to analyze the
running safety of vehicle on structure subjected to earthquake motion is briefly introduced. An idea
of structure to increase running safety is also introduced. A design standard, which was published
lately, to specify displacement limits of structure, is introduced lastly.
2 CWR ON BRIDGE
77
78 Track-Bridge Interaction on High-Speed Railways
Figure 1. A diagram to indicate CWR applicable span length (Fukazawa & Onishi (1962)).
Figure 2. Action of longitudinal resistance force and axial force distribution (Miyai (1976)).
In the study of a single span simply supported girder which exists in a confined section of CWR,
they set the maximum axial force in rail as shown in Equation 1, and some limit values for rail
fracture strength, track buckling strength and gap opening at rail fracture. As a result, they derived
a design diagram indicating the CWR applicable span length as shown in Figure 1 and concluded
that it would be practically possible to place CWR of 50 kg rail on 50 to 75 m span length girder
without expansion joints, depending on the magnitude of resistance force adjacent to the girder r0 .
PM = Pt + 0.5rl (1)
where Pt = axial force in a rail due to temperature change (Pt = E · A · β · t); E =Young’s modulus;
A = section area of a rail; t = temperature change; l = span length of a girder; r = resistance force
per unit length for a rail on girder; β = coefficient of expansion of rail.
As for the multiple span girders, Fukazawa & Onishi recommended to use the FF-MM type
support arrangement to relax the axial force distribution of rail in each span. Here, the FF-MM
means that fixed supports of two adjacent simply supported girders are placed on a same pier and
movable supports of next two adjacent girders are also placed on another same pier.
After the work of Fukazawa & Onishi, Miyai (1976) studied analytically the behavior of CWR on
multiple span girders using a computer program in order to expand the applicability of the FM-FM
type support arrangement, which is favorable for the seismic design of bridge piers.
He adopted the same assumption of which Fukazawa & Onishi used, and modeled the axial force
distribution of rail as shown in Figure 2. In his computation, the position to produce the same rail
and girder expansion is sought iteratively first to draw the axial force distribution diagram. Then,
Some experiences on track-bridge interaction in Japan 79
Figure 3. Maximum axial force of rail when expansion joints are placed at bridge ends (Miyai (1976)).
Figure 4. Maximum span length of girders when they exist in a confined section of CWR (Miyai (1976)).
the maximum axial force of rail, the displacement of rail at its end and the potential rail fracture
position to make the maximum gap opening are computed.
In the case of a bridge composed of multiple span simply supported girders, which have a
constant span length, the FM–FM type support arrangement and expansion joints at the bridge
ends, Miyai obtained some diagrams to show the characteristics of the maximum axial force of rail
(see Figure 3), the displacement of rail at its end and the maximum gap opening of rail. As the result,
he derived that the maximum axial force Pmax would not excess Pt + r · l/4 and concluded that the
practical maximum CWR length would be approximately 100 m on 10 girders when 60 kg rail was
used and some values were assumed as follows: r = 5 kN/m, Pmax = 1 MN, the rail displacement
limit y0 = 100 mm, and the rail gap opening limit D = 70 mm.
On the other hand, in the case that a bridge composed of multiple span girders exists in a confined
section of CWR, it had been thought that the axial force of rail was accumulated according to an
increase of the number of girders. However, he found that the axial force of rail would not be
accumulated in the middle region of the bridge because the position which produces the same rail
and girder expansion shifts toward the center of a girder in the region. He concluded that CWR
could be used on FM–FM supported multiple span girders as far as each span length is shorter than
50 m under the condition of r = r0 = 5 kN/m and Pmax = 1 MN.
Table 1. Arrangement of support and position of EJ for bridges exist in CWR section.
assuming the resistance force per unit length for a rail on girder r is less than 5 kN/m. The value
has been adopted in the Design Standard for Railway Structures (Steel and Composite Structures)
(1992). Then, the Design Standard for Railway Structures (Steel and Composite Structures) speci-
fies the characteristic value of longitudinal force due to CWR, when designing bridges, as 10 kN/m
for a track. And, the upper limit value of the axial load for a track is specified as 2 MN.
2.4 New non-ballasted track which mitigate axial force of CWR on bridge
The slab track as shown in Figure 6 is popularly used in Japan as a non-ballasted track. This type
of track, however, can not be installed striding over the ends of girders because the structure of the
slab track is reinforced concrete and the slab plate requires a homogeneous plane support using
Some experiences on track-bridge interaction in Japan 81
cement asphalt mortar. On the other hand, a new non-ballasted track, named “Floating ladder
track,” shown in Figure 7 which was developed by Wakui, Matsumoto & Inoue (1996), can stride
over the ends of girders because it is composed of prestressed concrete longitudinal beam and can
slide on the concrete bed. Then, it can mitigate the maximum axial force in a rail. Asanuma et al.
(2002) analyzed the characteristics of axial force of rail when the floating ladder track was used
striding over the ends of girders. Figure 8(a) shows an example of the analytical models with the
82 Track-Bridge Interaction on High-Speed Railways
FM-FM supported multiple span girders (5 girders of 50 m span length) and Figure 8(b) shows
the computed axial forces of rail by the temperature change of 40◦ C. They found that the floating
ladder track can reduce the maximum axial force by approximately 5 percents comparing with a
direct fastened track in this case.
The floating ladder track has already been used on some bridges of conventional revenue lines
(1067 mm-gauged lines) in Japan.
It is a very important item in designing a non-ballasted track structure whether it can reduce noise
and vibration of structure or not. In order to reduce the vibration of structure effectively, the
following measures can be thought: (1) increase of rigidity of rail, (2) smoothening of top surface
of rail, (3) lowering stiffness of rail fastener, (4) decrease of rigidity of intermediate mass of track,
(5) increase of intermediate mass of track, (6) improvement of supporting elasticity for intermediate
mass of track.
Some non-ballasted track structures as shown in Figure 9 have been used in Japan to reduce the
vibration of structure underneath.
The floating ladder track is also a very effective measure to reduce the vibration of structure
and then the structure borne noise. Okuda et al. (2003) measured the vibration acceleration of con-
crete viaduct. Figure 10(a) shows a comparison of the vertical acceleration vibration on concrete
Figure 10. Vibration reduction effect of floating ladder sleeper for structure.
Some experiences on track-bridge interaction in Japan 83
track-bed between the floating ladder track and the elastically supported embedded crosstie track,
when an identical passenger-car train of 16 ton axle load running at a speed of 80 km/h. Accord-
ing to the frequency analysis of the vibration, as shown in Figure 10(b), the floating ladder
track can reduce the vibration by approximately 20 dB over the elastically supported embed-
ded crosstie track. Therefore, the floating ladder track is a solution to the question of how
best to support the rail from the viewpoint of reducing structure borne noise. In other words,
the floating ladder track reduces the vibration by approximately 20dB in the audible range to
virtually eliminate the structure borne noise, which is the source of trouble with viaducts and
bridges.
change, ±200 mm due to train loading on double track and ±100 mm due to automobile loading.
Then, the type 1500 expansion joint device was developed through some tests conducted in the
Sanyo Shinkansen line (Hashimoto et al. (1975)) and installed on the suspension bridge.
After the completion of the construction of South Bisan-Seto Bridge, a running test using a train
composed of 10 locomotives (each weight: 100 t) and 3 freight wagons as shown in Figure 15 and
observed the performance of the transition girder and the expansion joint device. It was observed
that the maximum measured deflection and angular rotation of stiffening girders were almost equal
to those of computed values and the maximum breathing stroke of rail at the expansion joint device
as shown in Figure 16 was approximately 80 percent of the computed value (Iwata et al (1988)).
5.1 Background
Earthquakes occur frequently in Japan. Some are severe enough to damage tracks and structures.
According to the past experiences, track damages which affect the train operation are classified as
follows: (1) track deformation caused by the damage of roadbed, (2) track deformation caused by
destruction or large deformation of infrastructures, (3) angular rotation or gap between adjacent
structures, (4) settlement of abutment back soil, (5) buckling of track without damages of roadbed
or structures. Moreover, without any track damages or structure failures, the railway vehicle may
have a chance to derail when it is subjected to a severe transverse oscillation caused by earthquake.
86 Track-Bridge Interaction on High-Speed Railways
So, the running safety of vehicle during an earthquake is one of the most important problems in
design consideration.
Studies on the running safety of train on structures subjected to earthquake motions started in the
late 1960s in Japan when the practical construction investigation of the Honsyu Shikoku Connecting
Bridges was started. Nishioka (1969), Nishioka & Hashimoto (1980) studied the response behavior
of railway vehicles subjected to earthquake motions using 3D multi-body vehicle model. After their
studies, few studies had done until the Hyogo-ken Nanbu Earthquake (Kobe Earthquake) occurred
on January 1995 which caused catastrophic damages not only to building and highway structures
but also to railway structures. After the earthquake, extensive studies on the seismic design of
structures including strengthening methods were conducted. Consequently, the evaluation process
of structural safety and ductility of members subjected to severe earthquakes was reflected in the
Design Standard for Railway Structures (Seismic Design) published in 1999. As for the running
safety of train at earthquake, Matsuura (1998) studied using 3D multi-body vehicle model and
Matsumoto et al. (2003) studied using a vehicle/structure dynamic interaction model with 3D
multi-body vehicle model and 3D FEM. The outputs were reflected in the Design Standard for
Railway Structures (Deflection Limits) published in 2006.
Figure 18 shows the schematics of wheel/rail contact model. Although it is ideal to trace the
wheel/rail contact point using a 3D contact model, it is time consuming to use the model in every
iteration computation. In the DIASTARS, wheel/rail contact point is traced using a 2D contact model
assuming the following things: (1) the yaw and roll displacements are taken into consideration as
the motion of vehicle, but drift of contact point due to these displacements is ignored; (2) the creep
force is produced in the tangential direction at contact point; (3) the contact point and contact
angle α are obtained depending on the relative displacement between wheel and rail using some
pre-computed contact curves for wheel and rail surface profiles.
This interaction analysis model was verified using semi-vehicle model placed on a shaking table
as shown in Figure 19 which is consist of an actual track, an actual bogie and a half carbody model
(Miyamoto et al. (2004), Matsumoto et al. (2007)).
Figure 20 shows an example of experiment and analysis response results when the vehicle
model was oscillated transversely by 5 cycles of sinusoidal displacement of 0.5 Hz. Figure 21
shows threshold displacement curves to produce 3 mm uplift of wheel.
From these comparisons, it was found that the analysis model could predict the behavior of
railway vehicle subjected to earthquake motions.
Several analyses have been conducted on the running safety of train on structures subjected to
an earthquake motion. Figure 22 shows a schematic model to evaluate the influence of non-linear
response of structure. The hysteresis model of pier is a basic tri-linear type model (the Masing
model) as shown in Figure 23. Seismic waves are induced to bases of piers in the transverse
direction perpendicular to the traveling direction of train. The structure is excited with the seismic
motions of the same phase. The damping ratio of structure was set as 0.05. The train speed was set
as 300 km/h.
Figure 24 shows the influence of the non-linear response of structures that have different seismic
horizontal coefficient Kh (=(yield strength)/(self weight of structure)). It was found that the running
safety threshold ground acceleration would increase when the structure respond non-linearly.
Load (kN)
4 120
2 80
0 40
-2 0
0 2 4 6 8 10 12 14 16 0 2 4 6 8 10 12 14 16
Time (sec) Time (sec)
Experiment Experiment
6 160
Disp. (mm)
Load (kN)
4 120
2 80
0 40
-2 0
0 2 4 6 8 10 12 14 16 0 2 4 6 8 10 12 14 16
Time (sec) Time (sec)
Analysis A Analysis
(a) Vertical displacement of wheel (b) Wheel load
800
Non-linear structure Kh=0.3
700
400
300
200
Linear structure
100
Ground Acc. to make Kh=0.3 structure yield
0
0.0 0.5 1.0 1.5 2.0 2.5
Natural period of structure (sec)
Figure 24. Running safety threshold curves considering non-linear response of structure.
superstructure halve compared with conventional viaducts, and rigid-frame piers with braces and
damper as shown in Figure 25(a). This system can increase the lateral stiffness quite easily using a
small section of steel brace. The structure of damper is very simple. Details of damper and brace
are shown in Figure 25(b). The energy assumption caused by plastic shear deformation of web steel
plate is used as damping. In order to avoid total buckling and warping, flanges and stiffeners are
attached to the web plate.
A shaking table test was conducted with a 1/2.5 scaled model of rigid-frame RC pier with steel
damper and brace to confirm its seismic performance. The brace is anchored to the footing or
mid-columns. Relations between input accelerations and response displacements of specimens are
shown in Figure 26. In the figure, the results of RC frame without damper and brace are also shown.
It was confirmed that the displacements are well restrained compared with the case of RC frame
without damper and brace.
On the other hand, it can be suggested from Figure 23 that the seismic isolation structure
may increase the running safety during an earthquake because the threshold line of non-linear
response increases in the long period region. It is, however, necessary to take into consideration the
influence of angular rotation and alignment irregularity because they will have a large differential
displacement between adjacent structures that have long natural periods. Moreover, the influence
of the existence of track on the response of structures shall be studied.
Ikeda et al. (2005) conducted shaking table test as shown in Figure 27 and found that longitudinal
response of bridge on seismic isolation support would restricted approximately 20% because of
the existence of track.
90 Track-Bridge Interaction on High-Speed Railways
Figure 26. Relation between maximum input acceleration and maximum displacement of structures.
Oscillating direction
Rail
(longitudinal)
Rail
Rail fastener
Seismic isolated
bridge girder
Abutment
Figure 27. Shaking table test on seismic isolation structure with non-ballast track.
Table 4. Design limit values of girder deflection determined by riding comfort (for Shinkansen).
Tables 3 and 4 show the deflection limits determined by running safety and riding comfort,
respectively. Tables 5 and 6 show the angular rotation limits as well. Table 7 shows the limit values
determined by track damage criteria.
The fundamental idea of structural design for seismic conditions in the displacement limit stan-
dard is to reduce the possibility of derailment during an earthquake by adopting structures that have
higher running safety against an earthquake as much as possible. On the other hand, it has become
apparent from recent research that it is sometimes difficult to ensure running safety merely by
structural measures if earthquake motion exceeds a certain level and induced from the transverse
direction. Even in such cases, earthquake motion does not necessarily lead to injury of passengers.
However, considering the influence of high-speed running on damage, especially for Shinkansen
structures, appropriate and effective risk reducing measures must be devised from the viewpoint of
92 Track-Bridge Interaction on High-Speed Railways
Table 7. Design limit values for angular rotation and alignment irregularities determined by
track damage criteria in ordinary conditions.
both the hard and soft aspects of the entire railway system against severe earthquake motion (of an
intensity exceeding Level-1 earthquake motion). These include quick slowdown of the train by use
of an earthquake early detection system or limiting disasters after derailment by installing devices
for preventing large deviation of the train from the track.
The practical verification method for the transverse vibration displacement associated with
running safety was determined taking spectrum intensity SI as a verification index and Level-1
earthquake motion as a scale gauge for the sake of verification as shown in Figure 28. Limit
values were reviewed and determined taking into consideration: (1) the results of running safety
analysis using more than ten earthquake motions with different spectrum characteristics and (2)
the influence of angular rotation and alignment irregularities between structure ends.
It is also recommended in design to minimize the differential displacement of track surfaces in
a seismic condition as much as possible. The design limit values for the differential displacement
of track surfaces in a seismic condition are prescribed as shown in Tables 8 and 9.
6 CONCLUSIONS
Some experiences related to the track-bridge interaction in Japan were briefly introduced.
A brief history on the theoretical studies on CWR placed on bridge conducted in Japan was
introduced. A design guideline on the position of EJ depending on the arrangement of fixed and
moveable bridge supports and a new non-ballasted track which may mitigate the axial force of rail
were introduced.
A special expansion joint was used on long span bridges connecting Honshu (Main Island) and
Shikoku Island of Japan. Outlines of the bridge, the expansion joint device and the running test
which was conducted after the completion of the bridge are introduced.
Some experiences on track-bridge interaction in Japan 93
Figure 28. Limit value SI L of displacement associated with running safety in a seismic condition and response
values SI according to Level-1 earthquake motion.
Table 8. Design limit values for angular rotation and alignment irregularities
determined by running safety in a seismic condition.
Table 9. Design limit values for angular rotation and alignment irregularities determined
by track damage criteria in a seismic condition.
Angular rotation
(θ/1000)
Alignment irregularity
Folding/Parallel shift δ (mm)
A vehicle/structure dynamic interaction analysis program to analyze the running safety of vehicle
on structure subjected to earthquake motion is briefly introduced. An idea of structure to increase
running safety was also introduced. A design standard, which was published lately, to specify
displacement limits of structure, was introduced.
94 Track-Bridge Interaction on High-Speed Railways
REFERENCES
Asanuma, K., Matsumoto, N. & Wakui, H. 2002. Behavior of Newly Developed Floating LadderTrack Bridging
Structure Boundaries Subjected to Temperature Changes, Proceedings of Railway Mechanics, No.6, Japan
Society of Civil Engineers: 7–11 (in Japanese).
Fukazawa, Y. & Onishi, A. 1962. A Very Long Rail Laid on Bridge, Quarterly Report of RTRI, Vol.3, No.1:
26–31.
Hashimoto, K., Miyoshi, K. & Fujita, R. 1975. Running Vibration Test of Series 961 Shinkansen Test Vehicle,
Railway Technical Research Pre-Report, No.75–11, RTRI. (in Japanese).
Ikeda, M., Toyooka, A., Murata, K., Yanagawa, H., Kataoka, H. & Iemura, H. 2005. The Effects of the
Track Structures on the Seismic Behavior of Isolation System Bridges, RTRI Report, Vol.19, No.3: 23–28.
(in Japanese).
Ishiguro,Y. & Matsuura, A. 1988. Constructions of Honshu-Shikoku Bridges and Seto-Ohashi Bridge, Japanese
Railway Engineering, No.106: 19–24.
Itoh, F., Okuda, T., Hirata, G., Arai S. & Fujita R. 1972. Runnning Safety Test of Car against Derailment over
an Angular Bend, Quarterly Report of RTRI, Vol.13, No.2: 70–76.
Iwata, J., Miura, S. & Ando, K. 1988. Several Track Test Conducted at Opening of Seto Bridge Line, Journal
of Japan Railway Engineering Association, Vol.31, No.12: 18–21. (in Japanese).
Matsumoto, N., Wakui, H., Sogabe, M., Okano, M., Ohuchi, H. & Tanabe, M. 2003. Design Concept
and Practice Ensure Running Safety at Earthquake, IABSE Sympoium Report-Antwerp 2003, Struc-
tures for High Speed Railway Transportation, Vol.87, International Association for Bridge and Structural
Engineering: 46–47 on book and ANT129 on CD.
Matsumoto, N., Tanabe, M. Wakui, H. & Sogabe, M. 2007. A Dynamic Interaction Analysis Model for Railway
Vehicles and Structures Which Takes Into Account Non-linear Response, Journal of Structural Mechanics
and Earthquake Engineering, Vol.63, No.3, Japan Society of Civil Engineers: 533–551.
Matsuura, A. & Wakui, H. 1979. Allowable Bent-Angle of Long-Spanned Suspension Bridges Determined by
Running Property of Railway Cars, Quarterly Report of RTRI, Vol.20, No.3: 106–111.
Matsuura, A. 1998. Simulation for Analyzing Direct Derailment Limit of Running Vehicle on Oscillating
Tracks, Journal of Structural Mechanics and Earthquake Engineering, Vol.15, No.1, JSCE: 63–72.
Miyai, T. 1976. Theoretical Study of the Long Welded Rail Continuously Laid on Equally Spanned Bridges,
Railway Technical Research Report, No.991. (in Japanese).
Miyamoto T., Matsumoto, N., Sogabe, M., Shimomura, T., Nishiyama, Y. & Matsuo, M. 2004. Railway
Vehicle Dynamic Behavior against Large-Amplitude Track Vibration, Quarterly Report of RTRI, Vol.45,
No.3: 111–115.
Nishioka, T. 1969. A Theoretical Study on the Behavior of Railway Vehicles Considering Vibration of Track,
Journal of the Japan Society of Civil Engineer, No.172, Japan Society of Civil Engineers: 43–57. (in
Japanese).
Nishioka, T. & Hashimoto, S. 1980. Running Stability of Two-Axle Freight Car on Bridges at Lateral
Earthquake Shock, Journal of the Japan Society of Civil Engineers, No.296, Japan Society of Civil
Engineers: 61–72. (in Japanese).
Okuda, H., Asanuma, K., Matsumoto, N. & Wakui, H. 2003. Environmental Performance Improvement of
Railway Structural System, IABSE Sympoium Report-Antwerp 2003, Structures for High Speed Railway
Transportation, Vol.87, International Association for Bridge and Structural Engineering: 242–243.
Railway Technical Research Institute (ed.) 1992. Design Standard for Railway Structures and Commentary
(Steel and Composite Structures). Tokyo: Maruzen. (in Japanese).
Railway Technical Research Institute (ed.) 1999. Design Standard for Railway Structures and Commentary
(Seismic Design). Tokyo: Maruzen. (in Japanese).
Railway Technical Research Institute (ed.) 2006. Design Standard for Railway Structures and Commentary
(Deflection Limits). Tokyo: Maruzen. (in Japanese).
Terashima, M. & Hiraoka, S. 1997. Support Arrangement of Bridges to be Installed CWR, Structure Design
Documents, No.51, Japan Railway Civil Engineering Association: 2–6.
Wakui, H., Matsumoto, N. & Inoue, H. 1996. Ladder Sleeper and NewTrack Structures Development, Quarterly
Report of RTRI, Vol.37, No.3: 110–111.
CHAPTER 9
ABSTRACT: This paper analyzes the numerical methods used to assess the phenomenon of
longitudinal track-structure interaction in railway bridges, focusing on the key issue of combination
of actions.
The different computing methods are presented as examples of application for viaduct design.
1 INTRODUCTION
In railway bridges, the variations of temperature, the strains due to deck shrinkage and creep and the
action of railway loads can generate additional stress on continuous rails and thus induce relative
displacements between track and deck or subgrade.
The value of such additional stress, measured as the increment with respect to stress on the rail
at a point distant enough from the bridge, may exceed the maximum limit values according to
current standards, particularly where large expansion lengths can be expected (continuous decks
or long-span isostatic bridges).
On the other hand, the relative displacements between track and deck or subgrade can also
modify the conditions of track grid stability.
Therefore an analysis is needed of the interaction between rail and structure focusing on two
main aspects:
– Determination of the additional stress on rail and the eventual need of installing one or more
expansion devices;
– Determination of the absolute displacements of deck and relative displacements between track
and deck or subgrade, the latter shall be limited in order to avoid track grid general instability
due to ballast layer deconsolidation.
2 COMPUTING METHOD
95
96 Track-Bridge Interaction on High-Speed Railways
2.2.1 Rails
The rails are idealized by means of beam-type elements, with two nodes and three degrees of
freedom per node (longitudinal and vertical displacements and rotation in the vertical plane). As a
simplification, these elements are located in a horizontal line although not at their actual position
but at the upper height of the deck, which has no impact on the results (the diagram in Figure 1
shows different heights for the sake of clarity).
2.2.2 Subgrade
The subgrade is considered with infinite stiffness and idealized with connecting nodes located at
the same height of the rail where any node displacement is prevented.
2.2.3 Deck
The deck has been idealized using two types of elements, both beam-type elements with two nodes
and three degrees of freedom per node:
– horizontal elements, located at the height of the center of gravity of the deck section, having the
same parameters of bending and longitudinal stiffness as the said section;
– vertical elements, embedded onto horizontal elements, with a very large bending and longitudinal
stiffness; these elements connect the intermediate fiber of the deck with the bearings and with
nodes on the upper face of the deck, the latter being located at the same height of the nodes of
the rail.
Numerical methods for the analysis of longitudinal interaction 97
70
50
40 Loaded track
Unloaded track (good maintenance)
Unloaded track (fair maintenance)
30
20
10
0
0 2 4 6 8 10 12
Displacement (mm)
Figure 2. Resistance of track to relative displacements with respect to bearing per unit length (UIC 54 or
UIC 60 rails).
k = 12 kN per unit length of track, for unloaded track with fair maintenance level;
k = 20 kN per unit length of track, for unloaded track with good maintenance level;
k = 60 kN unit length of track, for loaded track;
uo = 2 mm in all cases
-10
-20
-30
-40
T (ºC)
Figure 3. Example of curve of temperature reduction equivalent to the strain due to shrinkage and creep.
braking/traction, bending, shrinkage and creep) is not correct as the model of rail–deck interaction
is itself non linear, due to the behavior of the union between track and deck or subgrade.
On the other hand, this law is also dependent on the track being loaded or unloaded, and therefore
it depends on the position of the train of loads, which further complicates a “step by step” non
linear calculation, which would be a more realistic approach.
On the other hand, considering expansion devices, the variations of temperature of the rail
and deck are both taken into account and thus the worst-case situations will be more than two as
previously described. Therefore it shall be necessary to find several combinations of variations of
deck temperature, including eventually the equivalent variations of temperature from the strain due
to shrinkage and creep, and variations of temperature of rail in order to fully assess all worst-case
assumptions.
Considering traffic actions, if train braking and/or traction are produced on the bridge proper,
once the horizontal forces are working the strain due to vertical bending has already occurred.
Therefore it seems that the proper method should consider two calculation steps. The first step shall
consider vertical loads (at their definitive position on the bridge) and then computing the bending
strain. The second step, where the model has already experienced strain due to vertical bending,
100 Track-Bridge Interaction on High-Speed Railways
F
N = 60 kN/m
60 kN/m
increasing N
FN
N =0
F0
2 mm u
Figure 4. Resistance of track against relative displacements with respect to bearing, as a function of vertical
load.
shall include the horizontal forces of braking/traction. This calculation is quite straightforward as
the characteristics of the non linear elements remain unchanged during the two calculation steps.
FN = F0 + µN
Table 1. Comparison of results with test cases according to UIC Leaflet 774-3 [12].
On the other hand, in the calculation of displacements, both absolute of deck and relative between
track and subgrade or deck, the linear superposition is not conservative. As in the previous case
the error is not significant, lower than 10% on average and never greater than 28% in the cases
analyzed, although great care must be taken in the analysis of the results as regards displacements
whenever carrying out this type of simplified calculations.
Figure 6 shows the results of displacements of rail and deck in the same case E1-3.
In most of the cases the simplified method should be sufficient. Nevertheless some bridges
can be labeled as “threshold” structures, for which after the analysis has been made using the
simplified method, the stresses in rail without expansion device are slightly over the permissible
levels. After a simplified analysis the actual worst-case situations will have been detected for the
rail, and a “step by step” calculation could then be executed for such situations. This will allow to
check how conservative was the first calculation as regards stresses, and then get more realistic
values of displacements. Chapter 4 describes an example of calculation for a viaduct with these
features.
102 Track-Bridge Interaction on High-Speed Railways
Figure 5. Comparison of stresses in rail with simplified and “step by step” methods. Case E1-3 UIC leaflet
774-3 [12].
3 VERIFICATION
3.2 Displacements
The relative displacements between track and deck are restricted in order to avoid ballast decon-
solidation. The limitation of deck displacements ensures compliance with limiting stresses in
the rail.
Numerical methods for the analysis of longitudinal interaction 103
Figure 6. Comparison of displacements of rail and deck with simplified and “step by step” methods. Case
E1-3 UIC leaflet 774-3 [12].
The verification on displacements stated by the standards [4] [12] are the following:
– Under loads of braking/traction, the relative displacement between track and deck or subgrade
shall be lower than 4 mm.
– Under loads of braking/traction, the horizontal displacement of deck in abutment or between adj-
acent decks shall be lower than 5 mm without expansion device or 30 mm with expansion device.
– Under traffic vertical loads of braking and/or traction and thermal gradient, the strain of the
deck due to bending shall not generate horizontal displacements of the upper side of the deck in
abutments or between adjacent decks greater than 8 mm.
– Under traffic vertical loads, with their corresponding dynamic factor, and temperature actions,
the strain of the deck due to bending shall not generate vertical displacements of the upper side
of the deck in abutments or between adjacent decks greater than 3 mm for tracks with a project
speed V lower than 160 km/h, or 2 mm when V can be greater than 160 km/h.
– With continuous rail, the horizontal displacements of the deck in abutment or between adjacent
decks due to daytime variation of temperature shall not be greater than a value in the range 10 mm
to 15 mm (to be defined by each administration; in the Spanish case: 13 mm for a maximum
daytime variation of temperature of 5◦ C [1]). Otherwise an expansion device shall be fitted.
In this case the displacements of the rail in the device due to a variation of temperature of
deck and rail (Tt ; Tc ) and due to shrinkage and creep shall be taken into account, while the
displacements due to braking/traction or bending can be disregarded.
4 EXAMPLE OF CALCULATION
An example of calculation is presented next, carried out with the simplified superposition method
described in 2.4.1 and the “step by step” calculation method described in 2.4.2.
110
20 35 35 20
Tt,ret,flu = −23◦ C.
4.3 Results
The first calculation has been carried out with the simplified method, where the deck undergoes
two variations of temperature (concomitant with a variation of temperature of the rail of 50◦ C) and
the vertical and braking forces.
In the case of traffic overloads four positions of the train have been considered. Figure 8 shows
the results of overall stresses in rail.
As can be seen there is a maximum of compression on the unrestricted abutment at 202.7 MPa.
Therefore the limit values of the standards are slightly exceeded (72 MPa added to 126 MPa of
confinement stress: 198 MPa).
For the simplified calculation the worst-case scenario has been identified as occurring for the
reduction of temperature of deck combined with the equivalent temperature of shrinkage and creep
and the train head located over abutment 2 in the instant of braking (Fig. 9).
For this situation a “step by step” calculation has been carried out. In the first step of calculation,
the variations of temperature of rail and deck are entered. In the following steps the vertical loads
are entered, advancing from the embankment adjacent to abutment 1 till the definitive position
shown in Figure 9. In this position the horizontal loads of braking are entered in the last step of
calculation.
Figure 10 shows the comparison of results for stresses in rail using both methods, for vertical
and horizontal forces and the sum of all actions.
As can be seen the “step by step” method implies a reduction of maximum compressions that
become lower than the limit values of the standards.
106 Track-Bridge Interaction on High-Speed Railways
Figure 8. Envelopes of stresses in rail due to variations of temperature, bending and braking, obtained with
the simplified method.
The verification of displacements are detailed next. Verifications 2 to 5 have been made for
the situation analyzed with the “step by step” method (the sign criteria for absolute displacements
adopted is [+] for direction from abutment 1 to abutment 2 and [−] for direction from abut-
ment 2 to abutment 1, the sign criteria for relative displacements is [+] for receding and [−] for
approaching):
1. Displacement of end of deck (absolute in abutment or relative between adjacent decks) due to
daytime variation of temperature (±5◦ C):
• In end of deck over E2: ±4.9 mm < 13.0 mm
2. Relative displacement between track and bearing (deck or subgrade) against braking/traction:
• Maximum (E-2): ±2.1 mm < 4.0 mm
3. Displacement of end of deck (absolute in abutment or relative between adjacent decks) against
braking/traction:
• Maximum (E-2): ±1.9 mm < 5.0 mm
4. Horizontal displacement of upper face of deck (absolute in abutment or relative between adjacent
decks) due to deck bending at deck end without expansion device:
• Maximum (E-1): 0.2 mm < 8.0 mm.
Numerical methods for the analysis of longitudinal interaction 107
5 BENDING
Stresses in rail (MPa) Step-by-step method
Simplified method
-5
20
BRAKING Step-by-step method
Stresses in rail (MPa) Simplified method
10
-10
-20
-60
-80
- 100
-120
-140
-160
-180
-200
-220
5. Vertical displacement of deck (absolute in abutment or relative between adjacent decks) against
deck bending (this value depends on the rotation of deck in bearing and the separation between
axis of bearing and end of deck):
• separation between axis of bearing in abutments and end of deck: 1.0 m
• maximum rotation in abutments (E1): 0.5 × 10−3 rad
• maximum vertical displacement in abutments: 0.5 mm < 2.0 mm
As can be seen, all limit values are easily complied with. Furthermore, the earlier comment on
stresses would not justify in this case the installation of an expansion device.
108 Track-Bridge Interaction on High-Speed Railways
5 CONCLUSIONS
The numerical methods of the analysis of longitudinal track-structure interaction have been
presented, where two different scenarios of combination of actions have been considered:
– simplified method of combination;
– “step by step” calculation method.
Both methods have been used with a set of test cases described in UIC Leaflet 774-3 [12].
The analysis of the results allows to characterize the simplified method as conservative for the
calculation of stresses in rail and reactions in bearings, but not conservative for displacements of
rail and deck.
In most of the cases the simplified method will be sufficient, although “threshold” cases can
occur where a thorough analysis of a specific situation could be needed using a “step by step”
calculation.
REFERENCES
[1] Comisión redactora IAPF. 2006. Borrador de Instrucción de acciones a considerar en el proyecto de
puentes de ferrocarril.
[2] Cuadrado, M. & González, P. 2000. Interacción entre carril continuo y tablero de puente. Calibrado del
modelo de cálculo según la Ficha UIC 774-3.
[3] Cuadrado, M. & González, P. 2004. Consideración de las deformaciones por retracción y fluencia en
el estudio del fenómeno de interacción vía -tablero en el proyecto de puentes ferroviarios. Revista de
Obras Públicas.
[4] Eurocódigo EN 1991-2. 2003. Acciones en estructuras. Parte 2: Cargas de tráfico en puentes.
[5] Fryba, L. 1985. Thermal interaction of long welded rails with railway bridges. Rail International. 3,
pp. 5–24.
[6] Fryba, L. 1997. Continuous welded rail on railway bridges. World Congress on Railway Research.
Firenze.
[7] González, P., Cuadrado, M., Nasarre, J. & Romo, E. 2002. Alta velocidad: fenómeno de interacción
vía-tablero en puentes. Revista de Obras Públicas.
[8] González, P., Cuadrado, M. & Romo, E. IABSE. 2002. Consideración del fenómeno de interacción vía-
tablero en el proyecto de puentes ferroviarios. Congreso puentes de ferrocarril: Proyecto construcción
y conservación. Madrid.
[9] González, P. & Cuadrado, M. 2000. Apoyo a la Dirección de los Proyectos de la Línea de alta veloci-
dad ente Córdoba y Málaga. Plataforma. Informe sobre trabajos específicos adicionales: Interacción
entre carriles continuos y tableros de viaductos ferroviarios o plataforma. Metodología y criterios de
dimensionamiento de aparatos de dilatación de vía.
[10] Ministerio de Fomento. 1999. EHE. Instrucción de Hormigón Estructural.
[11] Ramondenc, P. Track/Bridge interaction. 1997. World Congress on Railway Research. Firenze.
[12] Union Internationale des Chemins de fer. 1999. Fiche UIC 774-3R. Interaction voie-ouvrages d’art.
Recommendations pour les calculs.
CHAPTER 10
1 INTRODUCTION
In general, rails as major part of any railway construction rest on the subgrade. Thus the stresses
σ in continuously welded rails due to temperature change T are directly and totally related to
T with σ = αET . However, if the track is supported by a flexible structure like a bridge, the
homogeneous situation is disturbed and the track-bridge interaction has to be analyzed. In former
times track and the supporting structure had been treated and analysed separately. However, this
approach cannot be used if the rails are continuously welded and expansion devices have to be
considered. In this case the track-bridge interaction cannot be neglected in order to ensure stability,
safety and serviceability.
In this context, longitudinal loads are of special importance. These are caused by braking,
uniform temperature change of the supporting structure or bending of the bridge deck. In References
[Ruge et al., 2004, Ruge et al., 2005b, Ruge et al., 2005a] it has been demonstrated that each of
the loads can cause remarkable longitudinal rail stresses.
Apart from the above situations, an additional loading case is identified and treated in this
paper which is not mentioned in codes so fare. It is shown that additional longitudinal forces are
caused by the sudden change of the longitudinal coupling between track and bridge by a passing
train. A detailed discussion and mathematical description of this loading case is given in section 3,
numerical results are presented in section 5 in order to show the importance of this effect.
The investigation of longitudinal loads and their influence on the forces in continuously welded
rails on bridgedecks has been much discussed for the last 20 years. As a result the European
norm EN 1991–2 [EN9, 2003] provides information on loads on bridges, design methods and
approaches today. Together with national appendixes like DIN FB 101 in Germany a common
set of rules is available which will harmonize national norms throughout Europe. According to
Reference [DIN, 2003] different longitudinal loading cases are analysed separately considering a
nonlinear stiffness law of the ballast. Such separate treatments of the loading cases braking and
temperature change can be found in References [Ruge et al., 2004, Ruge et al., 2005b, Ruge
et al., 2005a]. A comprehensive treatment of longitudinal effects in general is presented in the
books [Fryba, 1996] chapter 14 and [Esveld, 2001] chapter 7. The maximum longitudinal stresses
109
110 Track-Bridge Interaction on High-Speed Railways
follow from a subsequent summation of the results corresponding to different loading cases. This
approximate approach completely neglects the influence of preceding events on the current load
process. In fact, a more realistic combination of loading cases is required to obtain correct results.
Then the sequence of events is of importance and the history of a load process has to be taken into
account. For this purpose, a truly nonlinear track-bridge interaction model resulting from a correct
combination of loading cases is developed in this paper. The nonlinear problem is solved by a
sequence of linear steps with incremental displacements; thus the overall system-stiffness depends
on the load-deformation history.
In statics, the stepwise linearized differential equations can be solved exactly and enables one to
establish a corresponding exact stiffness formulation. In dynamics, the exact dynamical stiffness
matrix is frequency-dependant and thus not available in the time-domain in a straightforward
manner. Therefore, in dynamics, the problem is solved by means of a variational formulation using
a quadratic interpolation for the rail-displacements in space and a linear one in time.
2 TRACK-BRIDGE INTERACTION
The above elastic coupling between bridge and rail can be visualized as a coupling shearelement
subject to a displacement difference uD as shown in Figure 1(b).
However, Equation 4 is valid for a virgin track-bridge system, which has not undergone any previous
deformation only. For a sequence of loading cases the situation is more complicated, as will be
explained in the following.
Figure 3. Deformation situation after a preceding loading case. (a) displacement difference (uR − uB ), (b)
deformation uD of the coupling element and (c) corresponding available capacity for a subsequent elastic
deformation.
Figure 4 for the case of a positive relative deformation 0 < uD < +ũ. Here, the terms kr and kl
denote the capacity for proceeding elastically corresponding to a possible positive and negative
additional deformation zD of the coupling element, respectively. The above available capacity can
be calculated using Equations (5) and (6).
kr = ũ − uD , (5)
kl = −ũ − uD . (6)
Longitudinal track-bridge interaction for load-sequences 113
At the same time, the sum of the absolute values of the positive and negative capacity is constant.
In Figure 3 it can be seen that the negative and positive available deformation capacity enclose a band
of width 2ũ. A subsequent loading case proceeds elastically if the additional relative deformation
zD of the coupling element,
zD = zR − zB , (9)
zR additional longitudinal displacement of the rail,
zB additional longitudinal displacement of the upper surface of the bridge, lies within this band.
Otherwise, the rail slips relative to the coupling element.
kl ≤ zD ≤ kr → elastic
(10)
zD < kl , zD ≤ kr → plastic
In case of a positive additional deformation of the coupling element, the positive capacity kr is
used to determine q, otherwise kl is relevant. Using Equations (5) and (6), formulations (11) and
(12) can be written as:
Equations (11)–(14) will be used for a derivation of stiffness formulations in the following
sections.
114 Track-Bridge Interaction on High-Speed Railways
Afterwards u12 due to the sequence f2 following f1 can be found by increments z added to u1 .
u12 = u1 + z →
C1 (u1 + z) + C3 (u1 + z)3 = f1 + f2
(C1 + 3C3 u12 ) z + 3C3 u1 z 2 + C3 z 3 = f2 + (f1 − C1 u1 − C3 u13 ) (16)
0
This equation is characterized by modified coefficients which depend on u1 and thus on the
load/deformation history. These considerations can be transferred to the nonlinear track-bridge
system. As explained in section 2.1, the response of the latter to a subsequent load strongly
depends on the loading history. Consequently, the total displacement uR,total of the rail is the sum
of the displacements due to preceding loading cases and the additional deformation zR due to the
current load.
uR,total = uR + zR ,
uB = uB + zB . (17)
Kz = r, (18)
for the additional displacements z a typical continuous track-bridge system as shown in Figure 1(a)
is analysed. Here, it is distinguished between an elastic coupling of rail and bridge and a plastic
situation where the rail slips relative to the structure.
The homogeneous solution zRh (x) can be normalized with respect to z0 = zRh (x = 0),
z1 = zRh (x = l) and zB .
So fare, the addition longitudinal forces L0h and L1h at the end points due to the homogeneous
solution are known from L = EAzR .
⎡ ⎤
−coth γl
⎢ ⎥
⎢ 1 ⎥
√ ⎢ ⎥
⎢ sinh γl ⎥
L0h = EAzRh (x = 0) = p cEA⎢
T
⎥, (21)
⎢ γl ⎥
⎢ tanh ⎥
⎣ 2 ⎦
0
⎡ ⎤
1
⎢ − sinh γl ⎥
⎢ ⎥
√ ⎢ coth γl ⎥
⎢ ⎥
L1h = EAzRh (x = l) = p cEA⎢
T
⎥, (22)
⎢ γl ⎥
⎢ −tanh ⎥
⎣ 2 ⎦
0
The last position p4 = 1 in p is provided with respect to the additional solution zRq due to
the right-hand side q with zRq (x = 0) = 0 and zRq (x = l) = 0 in order to keep the normalization
undisturbed.
The analysis is significantly simplified and applicable for all 4 loading cases if the right hand
side is interpolated in a linear manner.
x x
q(x) = q0 1 − + q1 . (23)
l l
−1
h4 (x) = [q0 sinh γ(l − x)] + q1 sinh γx] (24)
c sinh γl
zR = zRh + zRq ,
⎡ ⎤
0
√
cEA ⎢ ⎥
0
⎢0 ⎥
L0 = L0h + pT ⎢ ⎥, (25)
c ⎣ 1 1 1 ⎦
q0 coth γl − − q1 −
γl sinh γl γl
116 Track-Bridge Interaction on High-Speed Railways
⎡ ⎤
0
√
cEA ⎢ ⎥
0
⎢0 ⎥
L1 = L1h + pT ⎢ ⎥. (26)
c ⎣ 1 1 1 ⎦
q0 − − q1 coth γl −
sinh γl γl γl
Evaluating the equilibrium of forces at the points 0, 1, A and for the whole system, Figure 1,
x=0: L0 = k0 z0
x = L : −L1 = k1 z1
(27)
A: LA = kA zA
overall : LA = L1 − L0
(Ksc + Kk )z = r, (28)
⎡ ⎤
−1 γl
⎢ coth γl − tanh
⎢ sinh γl 2⎥⎥
√ ⎢ γl ⎥
Ksc = cEA⎢
⎢ ∗ coth γl − tanh ⎥ = Ksc
T
, (29)
⎢ 2⎥⎥
⎣ γl ⎦
∗ ∗ 2 tanh
2
⎡ ⎤
1 1 1
⎢ coth γl − γl γl − sinh γl ⎥
⎢ ⎥
1⎢⎢ 1 1 1 ⎥
⎥ q0 , γ 2 = c .
r = ⎢ − coth γl −
γ ⎢ γl sinh γl γl ⎥
⎥ q1 EA
⎣ γl γl ⎦
− tanh − tanh
2 2
⎡ x ⎤
1−
⎡ ⎤ ⎢ l ⎥
z0 ⎢ ⎥
⎢ x ⎥
p = ⎣ z1 ⎦, h = ⎢
⎢ l
⎥,
⎥
1 ⎢ 3 ⎥
⎣ q0 x q 1 x 3 ⎦
− 3x2 + 2lx + lx −
6EA l 6EA l
q0 = qR0 + p0 ,
(33)
q1 = qR1 + p1 .
The longitudinal forces L0 , L1 (L > 0: tension)
L0 EA 1 −1 z0 q0 l 2 q1 l 1
=− + + (34)
−L1 l −1 1 z1 6 1 6 2
are taken to establish the element stiffness matrix K and the corresponding right-hand side:
The element stiffness is completed by the external stiffnesses k0 , k1 and kA , shown in Figure 1.
⎡ ⎤
k0 0 0
K = KElement +⎣ 0 k1 0 ⎦. (38)
0 0 kA
More details concerning the static analysis are given in German written papers [Ruge et al.,
2004, Ruge et al., 2005b, Ruge et al., 2005a] and a summarizing report [Ruge and Birk, 2006].
The new aspect, treated in this paper, is devoted to the question, if the change in the coupling-
stiffness causes significant dynamical forces. Then the differential equation for the rail has to be
complemented by mass-accelerations with the mass density ρ [kg/m] of the track.
Here the exact solutions zR (x, t), zB (t) can be formulated but in the frequency-domain
zR (x, t) = ẑR (x)eiωt , zB (t) = ẑB eiωt ; however the excitation from coupling-change is highly transient.
Therefore we decided to establish a fully discretized formulation: quadratic in the space domain
(x), linear (Newmark) in the time domain (t).
118 Track-Bridge Interaction on High-Speed Railways
The discretization in the space domain results in a system of differential equations in the time
domain. The dynamic analysis caused by change of coupling-stiffness follows statical loadings;
thus additional displacements have to be considered which are denoted by z,
where mass matrix M, damping matrix D, stiffness matrix K and load vector Q are generated by
evaluating Hamilton’s principle.
t1 t1
δH = δ L(z, ż, t)dt + δzT Q∗ dt = 0. (41)
t0 t0
∗
Here Q represents nonpotential forces and L = T − V − W is Lagrange’s function with kinetic
energy, potential energy and work of external force, respectively.
d ∂T ∂V ∂W
− Q∗ + = . (42)
dt ∂ż ∂z ∂z
The kinetic energy of rails and bridge girder,
1 1
TRB = mR (x, t)[żR (x, t)]2 dx + mB żB (t)2 , (43)
2 2
T T
d ∂TRB x mR h hdx 0 z̈R (t)
= MRB (t)z̈(t) = , (44)
dt ∂ż 0 mB z̈B (t)
Here z̈R is the acceleration vector of the rail, z̈B the acceleration of the bridge, h is the column
of shape functions and mR = ρA [kg/m] is the mass density of the rail with cross section A.
The additional displacements zR of the rail are approximated by quadratic shape functions with
corresponding displacements p in the nodes as shown in Figure 5.
zR (x) = pT h, ⎡ ⎤
1 z0
(46)
hT = 2 [(l 2 − 3lx + 2x2 )(4lx − 4x2 )(−lx + 2x2 )], p = ⎣ z1 ⎦
l z2
l/2 l/2
z1 z2
z0
x
Damping of the system is assumed to be proportional to the mass and stiffness with corresponding
factors cK and cM .
D = ck K + cM M. (53)
The values cK and cM depend on the first 2 angular eigenfrequencies of the undamped system:
cK = 2D(w1 + w2 ), cM = cK w1 w2 .
The load vector depends on the displacements uB and uR from the previous loads as described
in Equation (2) and in Figure 3(b).
The quadratic interpolation uR = hT uR for the previous displacements describes any history;
either elastic
∂W x c(x, t)h(x)hT (x)dx − x c(x, t)h(x)dx uR (t)
= r(t) = − , (55)
∂z − x c(x, t)hT (x)dx x c(x, t)dx
uB (t)
⎡ ⎤⎡ ⎤
4 2 −1 −5 u0
c(x, t)l ⎢ 2 16 2 −20⎥⎢ u1 ⎥
r =− ⎣−1 −5⎦⎣ u2 ⎦
, (56)
30 2 4
−5 −20 −5 30 uB
The dynamical treatment of this load can be realized by means of a sudden change of the coupling-
forces like an impulse which acts in a time instant. However, the train needs some time to affect
the whole bridge to be in the loaded condition and thus a continuous change of the ballast stiffness
in the time domain is more realistic. In order to facilitate the analysis, the change of the coupling
stiffness is assumed to be constant along the bridge. It is represented by means of a continuous
function in time during a certain interval. The loaded situation starts from the unloaded value (cu )
and increases until cl within T seconds as formulated in Equation (58) and shown in Figure 6.
⎧
⎨ t t
cu 1 − + cl , t ≤ T;
ca (t) = T T (58)
⎩
cl, t > T.
The time t = 0 starts when the first wheel of the train enters the bridge and ends with t = T when
the last wheel leaves it. In every single time-step corresponding to the actual time-instant tj the
actual loaded coupling stiffness ca is treated as a constant value with the final maximum value cl :
Here c(x, tj ) is the actual coupling stiffness and ũ denotes the critical displacement of the coupling
element which is a constant value independent with respect to c(x, tj ).
The interface-force due to actual slipping follows from applying Equation (55):
c(x, t)h(x)hT (x)dx − c(x, t)h(x)dx uR (t) c(x, t)ũh(x)dx
r(t) = x x − x . (61)
− x c(x, t)hT (x)dx x c(x, t)dx
uB (t) − x c(x, t)ũdx
The numerical form follows from the quadratic interpolation of the previous displacements; the
right-hand side for an elastic history,
⎡ ⎤⎡ ⎤ ⎡ ⎤
4 2 −1 −5 u0 1
ca l ⎢
⎢ 2 16 2 −20⎥ ⎢ u1 ⎥ ca l
⎥⎢ ⎥ −
⎢ 4⎥
r= ⎣ · sign(zD )ũ⎢ ⎥
⎣ 1⎦, (62)
30 −1 2 4 −5⎦⎣ u2 ⎦ 6
−5 −20 −5 30 uB −6
The minimum r = 0 of this force in Equation (63) occurs if uD and zD are equally oriented. The
maximum occurs when they are opposite to each other.
5 EXAMPLES
Table 1. Geometry, material properties and loading data for simply supported bridge system.
Figure 7. Elastic and plastic regions due to warming up T = +30K, bending ŵ/L = 1/2500 and braking
p = +20000 N /m.
(a) Each loading case are analyzed separately and (b) Loading case is analyzed sequentially with
added linearly. correct combination.
Figure 8. Longitudinal rail stresses due to warming up T = +30K, bending and braking p = +20000 N/m.
loads with the sequential analysis of loading cases as shown in Figure 8(b), the latter gives smaller
values for both; maximum compression and tension. Table 2 and Table 3 show the numerical values
for both situations. The sequential loading analysis gives 27% less maximum compression than the
linear combination.
As the maximum value of each loading case does not appear at the same point, the maximum
value of the summation is not equal to the summation of maximum stresses of each loading case.
Longitudinal track-bridge interaction for load-sequences 123
Table 2. Maximum longitudinal rail stresses due to temperature change, bending and
braking obtained separately and added linearly.
Finally, the system’s answer to a change of the coupling stiffness is studied by comparing 3
different situations.
• Pure static analysis
• Sudden, impact-like change with dynamics
• Continuous change within a time-period T with dynamics
As previous load before stiffness-change warming up is taken because typically this load causes
plastic intervals in the coupling interface.
Figure 9 shows the resulting longitudinal stresses at the movable support for all of these situations.
The time-interval is taken to T = 1 sec. Obviously all curves tend to the static level. The sudden
change results in oscillating stresses with initial peaks whereas the continuous smooth change
generates a monotonic decreasing curve. It should be noted that the minimum stresses occur at the
moveable support.
124 Track-Bridge Interaction on High-Speed Railways
Figure 10. System plot for double-track bridge system of Altmühltal bridge.
Table 5. Geometry, material properties and loading data for Altmühltal track-bridge system.
Table 4 shows the maximum values of compression and tension in the rail. The notation T
indicates the loading case ‘warming up’. The subscript l for T denotes that the results where
calculated for a loaded track. The unloaded situation is indicated by Tu and only this situation is
followed by the load-case ’change of coupling stiffness’ with c.
Table 6. Maximum longitudinal stress of double track bridge due to change of coupling stiffness after
temperature case.
(1) Tu −21.974 29.077 −33.981 41.685 −21.974 29.077 −33.982 41.685
(2) Tu → Cstatic −31.448 45.125 −34.061 41.666 −22.011 29.064 −36.350 48.292
(3) Tu → Cdyn,sud −50.378 58.918 −34.085 41.707 −22.051 29.077 −40.408 52.693
(4) Tu → Cdyn,cont −31.473 45.139 −34.023 41.683 −22.013 29.077 −36.355 48.295
The first row dedicated to Tu shows the stresses due to ‘warming up’ without any load from
passing trains. Therefore the stresses appear twice. The maximum compression occurs at the right
moveable support whereas the maximum tension is located about 33 up to 38 m from the left-end
of the bridge.
Figures 11(a) and 11(b) show the longitudinal stresses in both tracks due to a train passing along
the ballasted track. Thus change of coupling stiffness happens only there. The compression stress
in the loaded track increases continuously (Fig. 11(a)) or oscillates (Fig. 11(b)). But finally, both
curves tend to the same final stress-level which is more or less the same as for the pure statical
analysis without including mass-accelerations. The coupling-effect onto the neighboring rigid track
is neglectable as can be seen from 11(a) and 11(b). Similar results occur when the train passes the
bridge along the rigid track as is shown in 11(c) and 11(d).
6 CONCLUSION
Modern railway tracks are characterized by continuously welded rails and by avoiding expansion
devices at the ends of railway-bridges.
Thus a careful treatment of the track-bridge interaction is of significant importance as is con-
firmed by European codes. There a nonlinear coupling stiffness in the track-bridge interface is
recommended; however without regard to load-sequences or any deformation history.
126 Track-Bridge Interaction on High-Speed Railways
Figure 11. Longitudinal stress of rail at the right-end of the bridge due change of coupling stiffness after
temperature case with dynamic analysis.
Figure 12. Stress of rail at the right-end of the bridge due to repetitive train-passings on rigid track.
In this paper it has been shown that regard to the history can reduce the maximum rail-stresses
such, that expansion devices can be avoided.
The importance of the loading case ‘change of coupling stiffness’ due to train-passing has been
clarified by treating three different scenarios; two characterized by dynamics and the third one by
statics. Results, achieved so fare, indicate similar rail-stresses: either found statically or dynamically
with a continuous change-over of the coupling stiffness from unloaded-to-loaded situation or vice
versa.
Longitudinal track-bridge interaction for load-sequences 127
These rail-stresses due to ‘change of coupling stiffness’ should not be neglected as is shown by
means of one example in the paper. On the other hand it has been found, that multiple loadcycles
from train-passing after temperature-increase in summer has happened typically proceed elastically
in interface-regions where temperature caused a plastic behaviour.
ACKNOWLEDGEMENTS
The cooperation on track-bridge interaction with Deutsche Bahn AG, represented by Dr. Lamine
Bagayoko and Dipl.-Ing Gerd Schmälzlin is highly appreciated.
REFERENCES
EN9 (2003). Eurocode 1, Part 2 (EN 1991–2). Actions on Structures; Traffic loads on bridges. European
Committee for Standardization (CEN), Brussels.
DIN (2003). DIN-Fachbericht 101. Einwirkungen auf Brücken. Berlin.
Esveld, C. (2001). Modern Railway Track. Zaltbommel: MRT Production.
Fryba, L. (1996). Dynamics of railway bridges. London: Thomas Telford.
Ruge, P. and Birk, C. (2006). Longitudinal forces in continuously welded rails on bridgedecks due to nonlinear
track-bridge interaction. Computer & Structures, 85:458–475.
Ruge, P., Birk, C., Muncke, M., and Schmälzlin, G. (2005a). Schienenlängskräfte auf Brücken bei nichtlinearer
überlagerung der Lastfälle Temperatur, Tragwerksbiegung, Bremsen. Bautechnik, 82:818–825.
Ruge, P., Schmälzlin, G., and Trinks, C. (2005b). Schienenlängskräfte auf Brücken infolge Biegung.
Bautechnik, 82:69–80.
Ruge, P., Trinks, C., Muncke, M., and Schmälzlin, G. (2004). Längskraftbeanspruchung von durchgehend
geschweißten Schienen auf Brücken für Lastkombinationen. Bautechnik, 81:537–548.
CHAPTER 11
Juan A. Sobrino
Pedelta & University of Catalonia, Barcelona, Spain
Juan Murcia
University of Catalonia, Barcelona, Spain
ABSTRACT: This paper describes the track-bridge interaction phenomenon in bridges for high
speed railways, proposing a methodology for the structural analysis of the substructure taking
into account the following aspects: horizontal loads and imposed displacements due to the long-
term behaviour of concrete and temperature using a step by step analysis and, if required, the
construction process, behaviour of ballast using a non-linear links between the track and the super-
structure and behaviour of POT bearings, interaction between foundation and ground conditions.
The methodology fulfils the specifications of Eurocode 1 and consist of modelling the whole struc-
ture (track-bridge) with a 2D or 3D model using linear bar elements and non-linear springs and the
analysis of the different short-time and long-time scenarios. To illustrate the methodology, three
case studies of concrete viaducts of the HSR line Madrid-Barcelona-French Border are presented.
The results are compared with those obtained from the simplified design methods.
1 INTRODUCTION
After the conclusion of the first Spanish High Speed Railway Line in 1992, connecting Madrid
and Seville, the strategic railway infrastructure plan developed by the Spanish Ministry of Public
Works as a part of the objective of the European Union (EU) of developing a Trans-European
High-Speed Rail System, includes the construction of more than 4000 km of HSR in a period of
fifteen years [1]. The directives for the rail system interoperability constitute an impelling element
for the railway sector, as new lines, trains and equipment within the EU countries should be either
built or renovated.
As a result of the complexity of the Spanish geography, approximately a 10% of the railway
system consists of bridges and tunnels. Construction of railway bridges for high speed lines repre-
sents a significant cost of the network. Due to the important magnitude of vertical and horizontal
loads, the design of these bridges requires a judicious selection of the structural configurations and
erection procedure.
129
130 Track-Bridge Interaction on High-Speed Railways
• Design of structural elements should be carried out according to the Spanish Codes for concrete
structures or the recommendations for the design of composite and steel road bridges.
3 TRACK-DECK INTERACTION
The design basis of the track-bridge interaction phenomenon is established in the Eurocode 1
[4] [5] and in the UIC 774-3 leaflet [6]. The interaction is taken into account in the numerical
model by means of non linear springs that reproduce the horizontal interaction of the system
rail + fastenings + sleepers and the deck (Fig. 1). Non linearity is modelled by a bilinear horizontal
force per unit rail length – relative displacement law, as shown in Figure 2. In the structural analysis,
the existence of rail expansion devices, the type and the loading and maintenance state of track
(affecting the value of the k parameter of bilinear law) and the substructure stiffness have also to
be considered. It is necessary to include the substructure in the track-bridge interaction model as
long as it can affect significantly the global behaviour of the bridge [7].
The situations in which the interaction appears are those where a relative horizontal displacement
between the track and the deck occurs. The UIC 774-3 leaflet specifies the main actions to be taken
into account: the changes in temperature in the rail and in the deck, the horizontal forces due to
braking and acceleration and the bending of the deck caused by vertical traffic loads (bending
generates horizontal movements at the end of the deck due to its rotation). The values of the above
mentioned actions are defined in the EC-1 [4] [5] and in the UIC 774-3. The linear combination of the
results obtained from the independent calculation of each action (temperature, braking/acceleration,
bending) is not valid since the problem is not linear. A rigorous study demands to carry out a step-
by-step non linear analysis (called complete calculation in the UIC 774-3), including all the actions
Structural analysis of high speed rail bridge substructures 131
F (KN/ml)
k=0 Loaded track
60
k=60 KN/m2
40
0
0 0,002 u (m)
and the loading conditions of the track (affecting the non-linear springs representing the effect of
the track-deck interaction). However, the UIC 774-3 admits the linear combination of the results to
check the additional stresses in the rail. For some specific cases, a simplified methodology using
diagrams and tables is provided to obtain the stresses in the rail and the reactions at the supports.
On the other hand, the deformation of the concrete deck due to creep and shrinkage can be as
important as for the temperature changes and should also be considered [8]. In [9] a method to
combine this action with the rest of actions is proposed in order to obtain the stress envelope for
the rail. The temperature changes and the creep and shrinkage are considered together in the same
load case, as an equivalent temperature change of the deck. The worst situation for the rail would
happen in one of these cases: a) maximum increase of temperature in the early ages (without creep
and shrinkage deformation), and b) maximum concomitant decrease of temperature and maximum
creep and shrinkage deformation. The braking/acceleration and bending results would be added
afterwards.
bed and bearings). The rails and the deck are modelled with beam elements in their centre of
gravity. The supports are modelled in the same way, taking also into account the loss of stiffness
due to the long-term shrinkage. Geometric and material non linearities have not been considered;
which would turn out to be suitable for very high supports. The foundations are represented as
equivalent stiffness for horizontal movement and rotation in the support base. The track system
(rail + fastenings + sleppers + ballast) and deck interaction is represented by non-linear springs
with a bilinear law according to Figure 2.
POT bearings, fixed, guided or sliding, are the most commonly used type of bearings in the Span-
ish high-speed railway bridges. They have two different friction coefficients (static and dynamic)
should be considered. This friction coefficient µ varies from 0.5% to 5%. The behaviour of the
POT for horizontal movements can be represented by a spring with a Coulomb’s friction law as
shown in Figure 3.
The model of the whole set in 2 dimensions is shown in Figure 4. In case there is no rail expansion
device in the end of the viaduct, it is necessary to include the adjacent platform (300 m behind the
abutment according to the UIC 774-3 leaflet [6]).
5 CASE STUDIES
The proposed methodology has been applied in three viaducts of the HSR Madrid-Barcelona, with
commonly used static arrangements.
As a first estimation, longitudinal forces can be evaluated to be equal to the friction force
generated when the bearing slides under vertical permanent loads: µND1 +D2 . On the other hand, at
the fixed point (in general placed in one of the abutments) the longitudinal force is evaluated as the
sum of the external horizontal forces due to braking, acceleration,
etc. (Fext ) and the compensation
of the forces of friction generated in the rest of the supports ( µND1 +D2 ). Therefore the bearing are
134 Track-Bridge Interaction on High-Speed Railways
usually expected to slide independently from the support stiffness. It is also assumed that moving
supports are unable to generate additional friction under vertical traffic load. These assumptions
omit the real effect of track-bridge interaction and substructure stiffness. In the following lines,
the results obtained with the methodology proposed in this paper are compared to these reference
values.
substructure. For high pier stiffness and/or low sliding friction coefficient, sliding is needed to make
movements compatible (case µ = 0.01). For very slender piers or high sliding friction coefficient
(case µ = 0.05) , the compatibility can be achieved by column deformation without bearing sliding.
Therefore the value is below µND1 +D2 +q as happens for the second scenario.
The force at the fixed point is lower than expected (Table 2) because piers take braking and
acceleration forces and also a part of these external forces are transferred to the embankments
through the rails by means of the track-bridge interaction. On the other hand, the continuity of the
rails can introduce over-stresses in the bridge system as bridge deformations are constrained.
Table 2. Longitudinal force in top of fixed abutment in Selles River and Averno viaducts.
% FH UIC
Viaduct µ %Fext + µND1 +D2 %Fext + µND1 +D2 +q simplified
Selles bridge, they are not slender enough to prevent sliding of the bearings for low sliding friction
coefficient. The force in the abutment is lower than the maximum friction admissible load due to
the capacity of the rest of the supports to take some horizontal load.
6 CONCLUSIONS
Track-bridge interaction has a main role in the global behaviour of the HSR bridges in the distribu-
tion of the longitudinal forces and therefore has to be taken into account in the structural analysis
of the substructure. A methodology to obtain longitudinal forces in supports has been presented in
this paper. It has been applied to three Spanish HSR viaducts and compared with the commonly
Structural analysis of high speed rail bridge substructures 137
µ %FH simplified
0,05 44%
0,01 50%
µ % FH , simplified UIC
0,05 71%
0,01 58%
simplified calculation procedures. Differences are shown between both methods. From the com-
parison it is shown the relevance of considering track-bridge interaction, sliding support behaviour
and support stiffness in the structural analysis. Further developments should include geometric
nonlinearity of high supports and variable ballast stiffness and sliding friction coefficient.
REFERENCES
[1] “Strategic infrastructures and transport plan”, Ministry of public works, 2005.
[2] “Code IAP – Actions on railway bridges”, Ministry of public works, 1972 (in Spanish).
[3] “Code RPX – Composite bridge Code”, Ministry of public works, 1995 (in Spanish).
[4] EN 1991-2 “Eurocode 1: Actions on structures. Part 2 Traffic loads on bridges”.
[5] EN 1990 PrAnnex A2 “Eurocode: Basis of design. Annex 2: Application for bridges”, 2002.
[6] UIC, Leaflet-774-3 Track/bridge interaction Reccomendations for calculations, 2nd edition. 2003.
[7] Manterola, J.; Astiz, M.A.; Martínez, A. Puentes de Ferrocarril de Alta Velocidad, Revista de Obras
Públicas No 3386, abril 2000 (in Spanish).
[8] González Requejo, P; et al. Alta velocidad: El fenómeno de interacción vía- tablero en puentes. Revista
de Obras Públicas No 3418., Febrero 2002 (in Spanish).
[9] Cuadrado Sanguino, M.; González Requejo, P. Consideración de las deformaciones por retracción y
fluencia en el estudio del fenómeno de interacción vía-tablero en el proyecto de puentes ferroviarios.
Revista de Obras Públicas, No 3446, Julio-Agosto 2004 (in Spanish).
CHAPTER 12
M.P. Petrangeli
University “La Sapienza”, Department of Civil Engineering, Rome, Italy
ABSTRACT: The construction of the first Italian HS Railways, linking Rome to Florence, was
completed at the end of the eighty when the bridge crossing the Arno river was opened to the trains
running at 250 km/h. This p.c. bridge has a 230 m continuous deck rigidly connected to the piers,
an expansion length of 115 m so resulting for the thermal effects.
In spite of the absence of joints in the ballasted track, its behaviour in about 20 years of service
has been excellent.
The cable stayed bridge over the PO river is the second example illustrated in the paper. It has
been completed in 2006 and will be operated at the speed of 300 km/h. The 192 m main span and
the two 104 m side spans made Rail Expansion Devices necessary at both the ends of the bridge:
it will be only exception on the whole Italian HS Railway network.
1 INTRODUCTION
The construction of the Italian HS Railway network begun with the 236 km line linking Rome to
Florence at a maximum speed of 250 km/h, first in Europe at the time.
Its construction started in 1970 and 193 km were put in service since 1977 but it was completed
only on 1989 because of the limited budget.
After a stop lasted more than ten years, new lines have been built and the final situation is
illustrated in Figure 1.
All the 1400 km Italian HS Railway network, once completed, will have the Continuous Welded
Rails (CWR) with the only exception of the cable stayed bridge over the PO river; for this reason
simply supported spans are utilized in almost all the viaducts of the new lines.
Some trough arches and continuous girders are the few exceptions, all respecting the expansion
lengths suggested in the annexe G of Eurocode 1 (EN 1991-2), i.e. 90 m for concrete and composite
decks and 60 m for steel structures.
The only bridge not respecting these limits is the one crossing the Arno river, designed before
the mentioned EC was issued, and therefore strictly monitored during its life.
139
140 Track-Bridge Interaction on High-Speed Railways
The Italian Railway (FS) asked to have the major spans deck composed by two separate box
girders, one for each track. This choice was justified by security reasons and by the will of an easy
maintenance.
The three central piers are rigidly connected to both the girders that are, on the contrary, simply
supported over the two piers of transition to the approach viaducts (Fig. 3).
The three central piers reach the bedrock through very large caissons (22 m diameter) so they
can reasonably be considered fixed at the base.
The bridge is located in a seismic area with a PGA of 0,25 g and has been designed, on request
by FS, to stand up also if a span should collapse because of an extreme event.
The Italian experience: two case studies 141
and the horizontal displacement of the upper deck edge due to end rotation is less than 1 mm.
According to Eurocode 1 and assuming
the maximum permissible expansion Length should be, in the case of a single bridge deck:
In spite of this discrepancy no disorder has been surveyed in the ballasted track in about 20 years
of service.
The interaction between track and structure was analyzed in the case of seismic actions too.
Non linear dynamic analysis were carried out both ignoring the presence of the rails (the ballasted
track is taken into account only as dead load) or considering the combined track/structure system.
The EL CENTRO NS accelerogram scaled to 0,25 g was assumed as input for the calculation.
The working presence of the track leads to a significant reduction of the bending moments in
the piers, up to 40%, as well as in the movement of the deck joint: +/−10 cm instead of +/−15 cm
(Figs 4a, 4b).
Of course large stresses in the rails due to this action arise. In this example they reach a maximum
value of 150 N/mm2 and therefore the capability of the rails to absorb them depends on the stress
level due to the temperature effects at the moment of the earthquake.
Figure 4a. Bending moment diagrams under seismic actions measured at central pier footing. Left diagram:
bridge + tracks; right diagram: bridge only.
Figure 4b. Bending moment diagrams under seismic actions measured at central pier top. Left diagram:
bridge + tracks; right diagram: bridge only.
and the river (Petrangeli 2006). Two approach viaducts, respectively 6 and 4 km long, complete
this work, the most important of the whole line.
Three types of structure are present in the crossing in addition to the standard approach viaducts
already mentioned: (i) the cable stayed bridge, (ii) 12 simply supported decks on the right bank
and (iii) two continuous p.c. box girders necessary to overpass the main embankments (Fig. 5).
The decks are subdivided in such a way that Rail Expansion Devices (RED) are necessary to
keep the expansion length within the allowable limits. This will be the only exception along the HS
Railway Italian network, all equipped with CWR.
The relevant part of the crossing has a 192 m central span and two 104 m long side spans.
The deck is a p.c. continuous box girder with the fixed point at one tower, sliding bearings at
the second tower and at the transition piers. Expansion lengths of 296 and 104 m derived from this
arrangement of the bearings, joints in the rails so being required. The height of the cross section
is constant and equal to 4,5 m (L/42,7) along the central span; it varies and decreases to 3,70 m in
the side spans, in order to fit the height of the other decks.
The towers are 60 m high from the footing, 51 m from the deck. The top of the towers, where the
stays are anchored, is a steel-concrete composite structure.
The stays are made of 55 to 91 zinc-coated, singularly greased and sheathed 0,6 super strands
(Della Vedova et al. 2006).
The foundation of each tower has the footing (shaped to reduce the drag force) supported by 28
piles, 2 m diameter and 65 m long.
Dynamic analysis: three different trains (ETR 500, TGV, ICE) have been considered for the
dynamic analysis considering the dynamic behavior of the vehicle as well as the irregularities of
the track.
The Italian experience: two case studies 143
Seismic analysis have been carried out in the elastic range according to the Italian Railway
Specifications and the European Code 8. Because of the low seismicity, these actions did not
design the bridge but few sections in the upper part of the towers, while they were relevant for the
bearings and the joints.
144 Track-Bridge Interaction on High-Speed Railways
All the decks have been built by cantilever method (Fig. 6) with cast in situ segments, with the
exception of the 13 simply supported spans made by precast beams.
A number of physical tests have been executed to assess the theoretical assumption, the most
outstanding being: (i) test on a half scale model reproducing a segment of the deck with a stay
anchorage, carried on in the yard; (ii) fatigue test on a full scale model of the steel box embedded
in the upper part of the tower to anchor the stays and (iii) fatigue tests on three stays (composed by
55, 73 and 91 0,6” strands) complete of anchorage. Both fatigue tests were carried out in the EC
Joint Research Centre of ISPRA (Petrangeli & Polastri 2004, Petrangeli 2006).
Due to the importance of the bridge, a large number of sensors have been permanently placed on
it. The monitored quantities are: loads on the piles, stress and temperature in the most representative
sections of the deck and the towers as well, forces transmitted by a number of stays and bearings,
geometrical data like the angular rotation of towers and the deflection of the decks and, finally, the
scour near the piers in the riverbed. All the data will be collected inside the cable-stayed deck and
from there automatically transmitted to a remote office located in Bologna that will manage all the
bridges of the line.
Loads Model 71 and SW2 multiplied by α = 1,1 as requested by the Italian National Code
(Ferrovie dello Stato 1995) have been considered while breaking and traction forces have been
assumed as per EC 1-2.
The Italian experience: two case studies 145
The LM 71 has been supposed to run both from Milan to Bologna and vice-versa (SW2 running
in the opposite direction) because of the lack of symmetry of the bridge. Also the relative position
of the two trains has been chosen as to maximize the studied effect.
The plastic shear resistances of the track for the unloaded/loaded conditions have been assumed
respectively 20/60 KN/m.
The pile foundations have been considered as elastic springs with two limit deformability:
– zero, in calculating the maximum force transmitted to the fixed bearing;
– corresponding to the maximum scour allowed in service (the piles have been supposed to be
free for 8 m depth) and to the lower bound of the soil characteristic, in calculating the maximum
displacements.
The detail of the mesh at the junction between the deck and the towers is shown in Figure 7.
The 1D elements representing the rail were made 4,5 m long, instead of the maximum value of
2,0 m imposed by FS, to fit the length of the deck segments (the bridge was built by cantilever
method). A sensitivity analysis showed the variations were negligible.
Figure 8 shows the most meaningful results. Both the maximum track-structure relative dis-
placements (3,5 mm < 5 mm) and the maximum stress in the rail (109 N/mm2 in compression and
104 N/mm2 in tension) satisfy the imposed limits.
Figure 8. Sap2000 model and results of structure analysis 1) Longitudinal force on fixed bearing; 2)
compression tension on track; 3) traction tension on track; 4) track-structure relative displacement.
4 CONCLUSIONS
Some considerations can be derived from the two case studies illustrated.
The 20 years oldArno bridge, also if operated at a speed now considered not very high (250 km/h),
has the CWR with 115 m expansion length and no problems have been registered in these years.
It means that with very stiff foundations and a framed structures probably the usual limits can
be slightly exceeded.
The Italian experience: two case studies 147
The cable stayed PO bridge put in evidence a different problem to solve in seismic regions, that
is the performance requested to the RED during a strong earthquake.
No damages were accepted in this case for the PO bridge, very expensive devices so being
necessary. This request should be deeply discussed since the seismic actions, in other bridges of the
same line equipped with the CWR, if unfavourably combined with the thermal actions, can bring
the rail to collapse.
REFERENCES
Della Vedova M., Evangelista L., Petrangeli M.P., Prevedini C. 2006. “The Stays of the Cable-stayed Bridge
over Po River: Design, Testing and Technological Choices”. ID 14-24 (Vol. 2 – pagg 434–435) – Session
14 Reinforcing and prestressing materials and systems – 2◦ FIB Congress – Naples, 5–8 June 2006
EN1991-2: Actions on structures- Part 2: Traffic loads on bridges EN 1991-2
Ferrovie dello Stato 1995. Sovraccarichi per il calcolo dei ponti ferroviari – Istruzioni per la progettazione,
esecuzione e il collaudo Istruzione n.1/SC/PS-OM/2298 del 2.06.95 agg.13.01.97
Ferrovie dello Stato 1996. Istruzioni tecniche per manufatti sotto binario da costruire in zona sismica. Istruzione
44B del 14.11.96
Petrangeli, M.P. 1991. A railway bridge over the Arno river near Arezzo for the Rome-Florence high speed
line, Industria Italiana del Cemento N. 657 Luglio-Agosto 1991
Petrangeli, M.P. & Polastri, A. 2004 Prove a fatica su un concio di torre del nuovo ponte strallato sul Po
Costruzioni Metalliche N. 4 Luglio-Agosto 2004
Petrangeli, M.P. 2006. Cable Stayed Bridge over river Po. Special issue on Italian concrete structures for the
Second fib Congress – Naples, June 5–8 2006 of Industria Italiana del Cemento 820
CHAPTER 13
J. Hess
BWG GmbH & Co.KG, Germany
ABSTRACT: Rail Expansion Joints REJ are some time underestimated during the planning and
design phase of bridge projects. For operators and maintainers they are than later on the root cause
of operating and maintenance troubles. As track work components do, they have to carry and guide
wheels. In addition, REJ compensate the length variations of rails and have to allow compensation
of longitudinal movements of rails caused by movements of engineering structures such as bridges
and viaducts. However in reality this means in details the compensation of the length variations
of rails, bridging of the gap of the structures, accommodation of vertical and horizontal rotations
of ends of structures and adjustment of the different track resilience at both sides of the RMJ. In
some case studies and outlooks it will be shown how REJ have been incorporated into engineering
structures built in the past or in the planning stage.
1 GENERAL
The volume of substances changes according to the ambient temperature. In physics, this behavior
is characterized by the coefficient of linear expansion. The coefficient of linear expansion is differ-
ent for every substance. One way of dealing with this phenomenon is demonstrated in the formerly
practiced track installation with rail joint gaps. These gaps between the rails provided them with
sufficient space to expand or contract, respectively, depending on the temperature. In modern types
of permanent way, rails are continuously welded. The longitudinal changes associated with temper-
ature variation have to be adjusted by the rail itself as well as the rail fastenings, including sleepers
and ballast, via means of tensile and compressive strength. This can only be achieved successfully
if the permanent way and the foundation show approximately the same expansion behavior.
However, there are areas such as bridge constructions where the different lengthwise movements
between bridge construction and permanent way would result in the bridge being damaged by the
permanent way. In this case, the lengthwise movement of the permanent way has to be separated
from the bridge construction by the respective devices. This is the field of application of the rail
expansion joint.
Rail expansion joints (REJ) are devices which permits longitudinal relative movement of two
adjacent rails, while maintaining correct guidance and support.
These longitudinal movements may be required in interrupted CWR (continuously welded rails),
bridge movement or a combination of both.
The maximum admitted movement of two tracks against each other is called “Expansion capacity
C”. It is evaluated in dependence of the geometrical frame conditions, as can be seen in Figure 1
with:
C = Dmax − Dmin (1)
The mean position is the position where the expansion capacity and the relative displacement of
rails are half way, and the bearers are in nominal position. The actual position shall be checked by
reference points.
149
150 Track-Bridge Interaction on High-Speed Railways
Figure 1. Minimum, maximum and mean position of rail expansion joints (REJ).
The mean position is used for design and acceptance. The reference points are also used for
installation.
This longitudinal movements influenced by
– Temperature
– Creeping and shrinking of the concrete
– Braking and acceleration
are calculated during planning of the bearing structure. Dependent on the guidelines for the maxi-
mum construction gap, the requirements of the bridge mounts and the maximum admitted distances
between the interpolation points the kind of REJ for each construction and its position in the
construction has to be fixed.
From the various possible constructions of REJ, for high-speed traffic only constructions without
interruption of the running edge are used, as for example on high-speed tracks in Europe (Germany,
Spain, Netherlands) or Asia (Taiwan).
Basically, two modes of action can be differentiated:
• REJ with fixed stock rails and movable switch rails (Fig. 2)
• REJ with fixed switch rails and movable stock rails (Fig. 3)
In rail expansion joints with movable switch rails there is an inevitable excess width of the track
gauge in the area of the wheel transition zone due to the relative movement of the switch rail. This
wide to gauge is a point of unsteadiness and leads especially in high-speed traffic to a discontinuous
run of the vehicles and thus to a reduced comfort and an enhanced abrasion.
In rail expansion joints with fixed switch rails and longitudinal moving stock rails there is no
widening of the gauge.
Rail expansion joints – The underestimated track work material? 151
Figure 2. REJ with fixed stock rails and movable switch rails.
Figure 3. REJ with fixed switch rails and movable stock rails.
The design of rail expansion joints resembles those of switches. Therefore, their large components
also consist of switch and stock rails. Two different construction principles are employed in order
to compensate for linear expansion. In case of the conventional construction principle the stock rail
is mounted firmly in longitudinal direction while the switch rail in closed position to the stock
rail is longitudinally movable. Since the stock rail features a circular geometry behind the switch
rail, the track gauge at the point of the switch rail changes with every displacement of the mobile
switch. Thus, the lengthwise movement of the switch rail along the stock rail changes the track
gauge. This causes railways to be uncomfortable and leads to increased wear.
In order to solve this problem, BWG (member of the VAE Group) developed a new generation
of rail expansion joints using a new design principle that transfers the lengthwise movement of the
152 Track-Bridge Interaction on High-Speed Railways
switch rail to the stock rail. In this case, the horizontal geometry of the stock rail corresponds to
an elastic bending line that ensures a constant track gauge in any expansion position and results in
reduced wear and higher traveling comfort. In order to provide the longitudinally fixed switch with
some freedom of movement (approx. ±30 mm), the switch and stock rails are aligned vertically
in a defined system via a special rail tie. In this connection, the stock rail is subject to a lower
restraining force than the switch rail.
Additionally, the restrain force generated at the switch rail and the stock rails differ due to
different friction coefficients of the synthetic rail pads.
The rail head of the switch rail shows geometry like the arching of a stock rail under its permanent
weight. The horizontal (elastical) bent stock rail produces a homogenous knife edge load on the
back of the switch rail, which prevents a diverge between switch rail and stock rail. To achieve the
required fixpoint switch rail and stock rail are fixed vertically by the rail fastening system, whereas
the stock rail is fixed with less power. Additionally, different restrain of the switch rail and stock
rails are created by inserting synthetic pads with different friction coefficients.
To bypass the gap different constructions are used in dependence of the length of the expansion
joint, which are adapted to the moment of inertia, the admitted bending and the railbase stress of
the rail track in a way, that the admitted values and the admitted distance of the bases of max.
0.65 m can be maintained:
• up to 300 mm (±150 mm): Standard rails or filled section rails at bridge joint.
• up to 600 mm (±300 mm): Use of a steel sleeper, which is fixed on the side carrier
enabling a longitudinal movement. It is fixed with a
crossbar control system in the movement groove.
• up to 1200 mm (±600 mm): Use of two steel sleepers fixed on the side carriers
enabling a longitudinal movement. A crossbar control
mechanism keeps the steel sleepers in a homogenous
distance in the movement groove.
The single components of the expansion joints are shown in the lay-outs and the sectional
drawings. This construction makes a homogenous bedding and elasticity of the track system possible
to a large extent.
The area of the bridge expansion joint differs in dependence of the expansion length. The
movement of the bridge produces a differing sleeper distance at the sleepers of the bridge expansion
joints. It has to be made sure, that the maximum railbase stress and arching is still not exceeded.
For a expansion length up to ±150 mm (SAV 300), the expansion joint will be bridged with
a larger moment of inertia, dependent on the profile of the standard rail profile (Vignol) or the
profile of the filled section rails.
If the expansion joints are larger, e.g. ±300 mm (SAV 600) or ±600 mm (SAV 1200), supporting
carriers are used above the joint. They consist of two steel profiles, which are located laterally of
the driving rail on the sleepers. The carriers are fixed immovably with the sleepers on the fixed
side of the joint and can balance the longitudinal movements of the bridge on the movable side
of the joint. Lengthwise movable steel sleepers are on the carriers as support of the driving rail,
depending on the maximum width of the bridge joint. They are centered in the bridge joint with an
arm- or crossbar control mechanism installed ahead.
Elastic ribbed base plates enable especially in case of larger bridge joints a more homogenous
arching line over the entire construction length of the rail expansion joints. Due to the special
characteristic of the elastic system of the bedding of ribbed base plates with its flat load deflection
curve dynamic parts of the wheel load on the sleeper are reduced significantly. The sleepers are
decoupled dynamically from the track and stay more evenly in the ballast due to the reduced
alternation of loads and reduced dynamic load parts as with inflexible bedding of the plates.
Additionally the elastic ribbed plates cushion the trackway with a base stiffness of 17.5 kN/mm
and reduced the impact sound. To increase the reduction of the longitudinal forces over the
sleeper into the ballast, the sleepers are connected on both sides at the head with connecting
irons. This connection is only disrupted at the bridge joint. In the slab track system an elas-
tic bedding is obligatory, this is done with the same rail bases, probably with an amended base
stiffness.
With the uniformity of the track gauge, the favorable conductance of longitudinal forces and the
homogenous track subsidence due to the elastically bedded track rail, the intervals of maintenance
of the rail expansion joints in this delicate area are influenced positively.
Rail expansion joints for bridges with a wide span can additionally provided with extra base
plates. These contain an elastic element, which adjusts the vertical arching line (rotation angle) of
the bridge. The expansion joints can be installed on fixed as well as elastic bases (ERL).
154 Track-Bridge Interaction on High-Speed Railways
Figure 5. Rail expansion joint SAV-B 300 (without crossbar control mechanism).
Figure 6. Rail expansion joint SAV-B 600 (with single crossbar control mechanism).
The drawings (Figs. 5–7) show the bridging of the bridge joint with the admitted rail expan-
sion joint device with and without crossbar control system and with up to two steel sleepers. In
dependency on the specific frame conditions of the construction and possible special construc-
tions of the construction joint (e.g. installation of transition slab or bridging constructions) also in
larger expansion lengths models without the shown crossbar control mechanism or steel sleeper
constructions are possible.
2.2 Rails
The stock rails are manufactured from profile UIC 60 E1 according to UIC-Code 861-2 with a
quality of 900 A according to UIC-Code 860 HT 350.
The switch rails are made of the asymmetric profile UIC 60 E1 A1 with a quality of 900 A
according to UIC-Code 860 HT 350.
2.3 Gauge
The gauge of the rail expansion joint amounts to 1435–1437 mm.
Rail expansion joints – The underestimated track work material? 155
Figure 7. Rail expansion joint SAV-B 1200 (with double crossbar control mechanism).
2.4 Components
2.4.1 Bridging girder
A steel profile with cross sections and specifications indicated in Fig. 9 is installed as bridging
girder. It is fixed at the side of the rigid bearing; for the steel sleepers and at the movable side,
longitudinal displacement is realized by respective fastenings with low creep resistance.
2.4.4 Sleepers
In the area of the rail expansion joint, turnout sleepers (e.g., turnout sleepers of BWG for ballast
and slab track or according to the type of slab track, e.g., sleepers PVT-M of Pfleiderer AG/Rail.
One for slab track type RHEDA 2000) are applied. The standard sleeper spacing in the area of the
rail expansion joint amounts to 0.60 m.
156 Track-Bridge Interaction on High-Speed Railways
3.1 Development
On transition areas such as abutment – bridge deck and bridge deck – bridge deck on piers, the
deformation of the civil structure (expansion, contraction, deflection) will excite lifting forces in
the rail support points directly adjacent to the bridge gap. These forces arise from the rotation angle
and offsets resulting from the deformation of the bridge deck as shown in Figure 8.
The lifting forces are to be calculated in accordance with the applicable regulations for railway
bridges. On bridges with very different length and overhangs or very large overhangs, the forces
of the rail fastener can exceed the limit of the standard rail fastening systems.
In cooperation with DB AG, BWG enhanced and modified the common turnout support point
“Elastic Ribbed Plate Support – (ERL)” in such a way as to allow to accept uplift forces up to
approx. 27 kN (standard rail support point loarv-300-1: 12 kN) while ensuring the same upwards
and downwards rail fastening elasticity. Authorizations for trial operations in network of the German
railway DB AG exists for these designs. Such support points have been installed on various bridges
in the high-speed lines Hanover–Berlin, Cologne–Rhine/Main and Nuremberg–Ingolstadt as well
as bridges in the region of Berlin and the High speed line in Taiwan.
Figure 9. Special support point ERL (mod.) for transition area of bridges.
Figure 10. Characteristic lines for the special elastic fastening support point.
158 Track-Bridge Interaction on High-Speed Railways
This design ensures a virtually even bearing and elasticity of the permanent way (track stiffness).
3.3 Components
3.3.1 Rail fastenings
Rail fastening is realized in accordance with the drawings of the special support points with tension
clamps Skl B 12. Other clamps or clamping plates may be used. With regard to ensuring the required
creep resistance, elastic inserts are used which are provided with the corresponding characteristics
(elasticity, coefficient of friction).
The fastening of the ribbed plate (bolted connection of the cap and the bushing/adjustment cone)
is identical to the one of the standard support point ERL. The horizontal support point stiffness is
not affected by the modifications of the upper elastomer spring and remains therefore unchanged.
3.3.2 Sleepers
Special support points in the area of the bridge joint may be installed on sleepers (e.g. sleepers
PVT-M from Pfleiderer AG/Rail. One for slab track type Rheda 2000, turnout sleepers of BWG) or
on blocks, arranged on the ends of civil structures. The maximum sleeper or support point spacing
in the area of the bridge joint is 650 mm. Al larger expansion paths, the special support points will
be installed in combination with rail expansion joints of BWG type or, if required, in combination
with customized solutions (e.g. adjustment plates as track transition constructions).
Figure 11. Evidences at superstructure ends for superstructures with slab track.
– The vertical offset is translated into a longitudinal inclination over the length of the adjusting
plate. The plates thus reduce the effect of the vertical offset at the bridge gap and the connected
lifting forces at the rail fastenings (Fig. 12).
– If the adjusting plate is applied at the joint between two bridge superstructures, the end tangent
rotation angle occurring between the two superstructure ends is divided in smaller angles so
160 Track-Bridge Interaction on High-Speed Railways
that the rail base plate forces from the end twist of the superstructures are reduced considerably
(Fig. 13).
– Great movements of the joint are divided to smaller joint displacements between the adjusting
plates so that the admissible rail base plate distances are adhered to (Fig. 14).
The application of the adjusting plates generally provides evidence for the lifting forces, if need
be, in combination with the aforementioned special base plates.
Transition slab A is situated above the bridge gap, its length depends on the position of the
bridge supports. Transition slab are installed next to transition slab A if the overall dilatation at
the movable bridge gap is that big that by a distribution over two gaps the admissible base plate
distance cannot be adhered to.
At the gaps of the transition slabs, locking constructions ensure that the gaps do not open beyond
the maximum value of the rail base plate distance.
Figure 14. Transition slabs for the compensation of great longitudinal movements.
Rail expansion joints – The underestimated track work material? 161
5 EXAMPLES OF REALIZATION:
Figure 15. Top view of slab track, rail expansion joint and transition slab.
– Bridging girder of Co. STOG with 4 base plate lines (direct fastening at the steel plate) and
lengthwise movable and rotary bearing above the expansion joint Bridge – Ramp,
– 2 short transition plates for lateral guidance of the bridging girder.
Lifting forces still exceeding the capacity of standard rail fastenings despite this special design
can be accommodated by special base plates also designed by BWG and called Elastic Bridge
Support Point – mod. ERL.
In relation to the problems that occurred and to the alternatives (fundamental changes to the bear-
ing structures to reduce deflections and foundation measures for a further reduction/prevention of
settlements), the depicted and realized design (4 rail expansion joints were installed) represents
an economic and sustainable solution. As shown beyond mere static/dynamic aspects safety-
relevant issues have been covered as well, as for example with additional equipment/check rails
for derailment protection. Similar to the bridging designs already realized in 1995 at the Havel
and Havel-Waterway-Bridge, it can be considered as a standard solution for great longitudinal
movements, deflections and if needed in combination with the special base plates for high lifting
forces.
5.2 Hongkong, Airport Express, Tsing Ma Bridge, Ma Wan Viaducts, Kap Shui Mun Bridge
The Lantau Fixed Crossing is formed by the world’s longest suspension bridge, the Tsing Ma Bridge
(TMB), the Ma Wan Viaducts and the Kap Shui Mun cable-stayed bridge. Parameters to be taken
into consideration included a 2.2 m gap, a speed of 140 km/h, and about 198 trains per day on an
average.
The main problems to solve were the compensation of the length variations of rails, the bridging
of the gap, the compensation of the rotations of bridge around the vertical or horizontal axis and the
adjustment of the different track resilience at both sides of the RMJ. VAE has developed a solution
with a continuous running table and a continuous running edge to ensure a smooth ride. Over the
whole length of the RMJ there are no gaps which leave the wheels unguided. The possible 2,2 m
gap between the abutment and the bridge is divided into 4 small gaps by means of sledges. The
supporting structure for the REJ is designed as a flexible connection between the primary structure
and the abutment.
The main goal concerning the design of the REJ’s was to introduce a modern technical solution
with an optimum of
Riding comfort
↓
less wear and noise
↓
longer life cycle and less maintenance
Another goal during the design period was to find and implement as many approved trackwork
solutions as possible. The design of the supporting structure had to meet the demands imposed
upon the track with respect to vertical and horizontal acceleration and riding comfort as well as the
requirements mentioned above.
VAE has developed a cast tank-shaped expansion sleeve made of high manganese steel in order
to accommodate a UIC 60 thick-web stock rail. In principle the design follows the switch design
principles for a chamfered switch with straight machining for the foot of the stock rail. The transition
from the stock rail to the expansion sleeve or vice versa remains constant over the whole range of
movements.
For bridging the gaps widths of 1410 mm respectively 1670 mm, VAE finally decided on a
solution with 3 sledges. These sledges divide the wide gap into 4 small gaps enabling the adherence
to the required maximum base plate distances.
Rail expansion joints – The underestimated track work material? 163
An equal size of all four spacings is guaranteed by means of a lever connection mounted below
the sledges.
The connection between the abutment at Tsing Yi and the primary bridge structure is made by a
flexible “spline girder” and an “end girder”. The spline girder transforms all rotations around the
vertical or horizontal axis into longitudinal movements by forming a smooth sag (concave) or crest
curve (convex).
The longitudinal movements of each track on the Tsing Ma Bridge (TMB) are also transmitted
to the end girders via the spline girders. The end girders are mounted on 4 vertical bearings and are
guided by 4 horizontal bearings. These bearings can be adjusted hydraulically during installation
and slide upon polished stainless steel bearing plates.
6 CONCLUSION
Rail expansion joints of BWG and VAE are applied in the area of bridge constructions and in
normal conditions as well as in geologically instable areas. They are equally suited for ballast and
slab track. For Vignol rails, the standard expansion lengths 300 mm, 600 mm and 1200 mm are
available. Customized expansion lengths and special designs can be realized upon consultation and
in cooperation with the builder. Standard rail expansion joints are designed to be easily integrated
in the general planning of the permanent way on bridges and adjoining thrust bearings and soil
constructions. They do not require any particular changes to the building design. In case of special
designs, as they may be required for great end tangent rotation angle and/or great expansion lengths,
an early coordination between bridge planner, planner of the permanent way and producer of the
rail expansion joints is absolutely necessary to develop an economic and low-maintenance solution
that meets all requirements.
164 Track-Bridge Interaction on High-Speed Railways
REFERENCES
Bringfried Belter, Peter Ablinger, Josef Hess, Gilbert Waldmann Railway Track at the High Speed Line
Cologne – Rhine (Main – Slab Track) Eisenbahn-Ingenieurkalender – EIK – 2002
Systematical Decision Ballasted Track or Slab Track Report to results of the analysis and examination
within the scope of the project “Fahrbahnstrategie SMP-T”, published by ifv Bahntechnik (Project team
Fahrbahnstrategie, DBSystemtechnik, Strategy Consultancy Fontin & Company, ibt Dr. Ablinger)
Special constructions of Rail Expansion Joints Report about development and adaption of Rail Expansion
Joint SAV60 – 1200 and Elastic Ribbed Base Plates for the Bridge Hollandsch Deep in the course of High
Speed Line HSL Zuid, The Netherlands EI – Eisenbahningenieur (57) 4/2006
Johannes Rohlmann, Josef Hess New standard for turnouts and rail expansion joints for high-speed
traffic – installation in a high-speed track in Taiwan Track System Development, Engineering –
Construction – Experiences RTR Special - SLAB TRACK, 09/2006
Johannes Rohlmann, Josef Hess New standard for turnouts and rail expansion joints for high speed traffic
with large scale operation in Taiwan Eisenbahntechnische Rundschau – ETR, 07+08/2007
Stephan Gerke, Jürgen Haase, Josef Hess Development and construction of turnouts VDV Schriftenreihe
Band 26 Gleisbau: Planung – Bau – Vermessung
Jürgen Haase, Josef Hess, René Brehm Turnouts in High Speed Applications RTR Special – The German
High Speed Rail System, Evolution • Quality • Track construction, 03/2008
CHAPTER 14
J.T.F.M. Tünnissen
Joep Tünnissen Dynamic Engineering Consultancy, Veghel, The Netherlands
ABSTRACT: The structures and track system which are part of the Dutch High-Speed Railway
connection between Amsterdam and Paris, have all been analyzed for their dynamic behavior with
regard to structural integrity and passenger comfort. This paper describes the general approach of
these dynamic analyses as performed in the High-Speed Line-Zuid project, and goes into more
detail with regard to bridge-track interactions at the bridge across the Hollandsch Diep, one of the
most eye-catching and largest structures in this project. Relevant issues are the optimization of the
level of passenger comfort by introduction of a pre-camber in the alignment of the track system and
the dynamic behavior of the steel transition slabs, which as a special structure in the track system
allow for the horizontal expansion and contraction of the bridge.
1 INTRODUCTION
October 2007, the Dutch part of the High-Speed Railway connection between Amsterdam and Paris
nears its completion and thereby its goal to reduce the travelling time between both cities to just
3 hours. In the 125 kilometers from Amsterdam, via Rotterdam to the Belgium border, of which
85 kilometers have been destined for high-speed railway, trains will pass 170 different structures,
designed to cope with train velocities up to 300 km/h.
In the 2nd half of the 90s the HSL-Zuid Project-organization, representing the Dutch State
Department of Transportation, developed the visualization and engineering tools for the archi-
tectural and structural elements in the High-Speed Line-Zuid project. Due to its magnitude and
complexity it was decided to divide the contract into 7 subcontracts. 6 of these subcontracts dealt
with the design and construction of the railway structures, each covering a separate part of the
track. They were granted to different joint ventures between contractors in the year 2000. The 7th
subcontract covered the design and construction of the track system as well as the future mainte-
nance of the entire railway system and was granted to Infraspeed in 2002. The author has been a
member of the design team in 4 out of these 7 subcontracts, as an advisor on dynamic aspects and
as the responsible party for the dynamic analyses performed on the primary (main structures and
track system) and secondary (architectural elements and noise barriers) structures.
The Dutch terrain has required many adaptations to the high-speed railway structures and track
system as the track encounters highways, rivers, canals, ditches and environmentally important
areas on its way. Together with the necessity for piled foundations, due to the soft clay type of soil
in the western part of the Netherlands, the track has become a chain of different structures with
dilatations generally every 20 to 30 m. Dealing with the design criteria concerning the dynamic
behavior of these structures and the implementation of a ballastless track system, has made the
HSL-Zuid project a challenging engineering experience.
165
166 Track-Bridge Interaction on High-Speed Railways
The natural and man-made obstacles in the path of the track, the need for pile foundations and
the ever developing engineering and architectural insight during the design phase, have led to a
variety of structures. Some of these structures are highly visible, such as the elevated long-viaducts
near Hoofddorp and Bleiswijk (see Fig. 1), and the bridge crossing the Hollandsch Diep, which
with a total span of 1192 meters is the longest HSR-bridge between Amsterdam and Paris (see
Fig. 2). Others are hardly noticeable, such as the settlement-free slabs, which cover about 33 km of
the track and with their typical length of 30 m per slab often provide the link with other types of
structures. Except for the train passengers, some major achievements are not visible at all, such as
the Ringvaart aqueduct and the tunnels underneath the Green Heart, with a diameter of almost 15
meters, one of the largest drilled tunnel in the world, and the rivers Oude Maas and Dordtsche Kil.
Due to the soft clay type of soil in the western part of the Netherlands most of these structures are
supported by pile foundations, reaching into the Pleistocene sand bed. Only in the last 3.5 kilometers
towards the Belgium border the sand bed reaches the surface and provides a solid foundation. At
this location the transition into a ballast track is established in order to connect to the Belgium part
of the high-speed railway track.
The prize-winning design for the bridge across the Hollandsch Diep by architects Benthem &
Crouwel, is a result of a competition held by the HSL-Zuid Project-organization. The optimization
of the design and the final construction of the bridge was in the hands of HSL Drechtse Steden,
a joint venture of contractors responsible for the track between the city of Barendrecht and the
southern end of the bridge. Consisting of steel box-girders and U-shaped sections topped by a
concrete deck, the 10 main spans measure 105 m each to coincide with the spans of the old railway
bridge located next to it. The V-shaped hammer-pieces with a length of 45 m and a maximum height
of 11.40 m are interconnected by 60 m long field members. In the engineering phase minor changes
to the columns were introduced in order to obtain a maximum spread of the rubber bearings. The
increase of restraint at these locations resulted in an increase of the natural frequency of the bridge
which was beneficial to the level of passenger comfort.
The choice of a ballastless track system is based on economics, ease of maintenance and favorable
experiences with this system abroad. However, due to the soft soil conditions and the variety of
supporting structures with their inherent need for dilatations, the classical solution of a continuous
ballastless track could not be implemented in the HSL-Zuid project without some major adjust-
ments. The task of coming up with a solution was given to Rheda 2000 vof, which led to the
introduction of 2 different types of track. One, a continuous slab poured directly onto the structure
in areas which are relatively insensitive to settlement such as tunnels and slabs on embankment
and two, a jointed slab which is poured on an intermediate layer, consisting of a 4 mm thick poly-
propylene geo-textile op top of the structures in settlement sensitive areas. The jointed slab is
anchored to the structure in pre-designated free-drilling zones by means of HILTI high quality
stainless steel dowels with a diameter of 40 mm. This is the most commonly type used throughout
the track (67%) for structures such as the settlement-free slabs, viaducts and bridges with dilatations
approximately every 15 to 30 meters, but also on the bridge across the Hollandsch Diep which is
categorized as being sensitive to settlement/vertical deflection.
In the 163 km of Rheda 2000® slab track system, the rails are the only continuous elements
connecting adjacent structures. They are held in place by a Vossloh type IOARV 300 rail-fastening
system which is provided with a highly elastic intermediate layer. These layers are responsible for
the transfer of horizontal and vertical forces into the Pfleiderer type B355 W60M concrete bi-block
sleepers. The Rheda 2000® slab track system is completed by casting the prefab concrete sleepers
into a reinforced concrete slab on site. The reinforcement consists of lattice trusses which provide
stable dimensions and assures the required gauge of the track. The concrete slab grade B35, as
used in the HSL-Zuid project, has a standard height, without cant, of 240 mm and a width of 2600
or 2800 mm, depending on the location. The slab is reinforced throughout its entire length for
systematic prevention of cracks. See Figure 3.
Fastening IOARV 300
Sleeper B355 (c.t.c. 650 mm typical)
3000
2600
Dowel
232
240
Settlement-Free Plate
Figure 6. Rough positioning of Rheda 2000 with Fassetta. (Photo: Courtesy of Mr. P. Meijvis, DMC bv, The
Netherlands)
The interconnecting components of the Rheda 2000®track system, being the stainless steel
dowels and the intermediate layer have undergone several tests in order to determine their capacity
to withstand fatigue loadings (dowels) and to establish the stiffness characteristics and frictional
behavior under static and dynamic loadings (intermediate layer). Dynamic analyses have been
performed on the interaction between structures and track system near transitions, especially with
regard to the dynamic forces in the rail-fastening system.
Dynamic aspects of the high-speed railway bridge across the Hollandsch Diep 169
Due to the fact that the engineering phase for the structures started 2 years prior to that of
the track system, assumptions were made with regard to the system’s mass ranging from 650 to
3750 kg/m per track. Without cant, the mass of the Rheda 2000® slab track with one pair of UIC60
type rails eventually comes down to approximately 1800 kg/m per track.
4 DYNAMIC ANALYSES
T 1/3
LIh = 43.1 |av (t)|3 dt ≤ 45 (1)
0
100
90 100% Satisfied
Passenger (in-) comfort [%]
100% Unsatisfied
80
the in-betweens
70 LIh limit value (45)
60
50
40
30
20
10
0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200
LIh value
Figure 7. Empirical data, source for the LI h comfort criterion as per ERRI D190.
of accelerations at floor and seat level. A typical measurement period is 5 minutes in which data is
collected every 5 seconds, resulting in a total of 60 measurements per period. Measurements are
to be taken at the maximum operation velocity, 300 km/h in this project, and in all three (x:y:z)
axis, resulting in one measurement every 417 m. Data is processed, filtered and weighted into 50%
and 95% probability ranges. The required comfort level of maximum 2 is applicable to both seated
[NVA ] and standing [NVD ] positions, as per following formulas:
NVA = 4(aW
ZP95 ) + 2 (aYA95 ) + (aZA95 ) + 4(aXD95 ) ≤ 2
b Wd 2 Wb 2 Wc
(2)
NVD = 3 16(aW
XP50 ) + 4(aYP50 ) + (aZP50 ) + 5(aYP95 ) ≤ 2
d 2 Wd 2 Wd 2 Wd
(3)
In order to predict the field measurements dynamic analyses have been performed before the
actual installation of the Rheda 2000® slab track system, and with the train types specified in
paragraph 4.2. Assumptions have been made for the accelerations in the horizontal, lateral and
transverse direction based on the ratio (1:2:3) ( source: prof. C. Esveld, TU Delft). By collecting
data every 417 m the chance that relevant data on smaller structures are included tends to be small.
During the passage of the 1192 m long bridge across the Hollandsch Diep, the governing structure
with regard to level of passenger comfort, only 3 field measurements are collected out of the 60
in 1 period. By assuming that structures in front of and following the bridge will show an equal or
better comfort performance, a ratio of the weighted 50% and 95% train accelerations (aW W
Z50 /aZ95 )
2
of 1.0 is derived. This leads to a maximum allowable weighted RMS-value of 0.210 m/s . Applying
a weighting factor of 0.40 this results in a non-weighted RMS-value of 0.525 m/s2 . Due to the fact
that structures before and after the bridge will most probably show better comfort performances,
this approach is considered to be on the conservative side.
1 of this guideline and are shown in Figure 8. For the THALYS and IC3M trains, single and
double configurations are considered, identified by index 1 and 2. The THALYS2 characteristic
is equivalent to train type B in Annex F of the European standard EN 1991-2:2003. Hence, the
dynamic analyses have been performed with 5 real train types.
To obtain the vertical body accelerations from these train types, they have been modeled as
SDOF spring-mass systems with a mass equal to the axle-forces divided by the g-force. The spring
frequencies range from 0.80 to 1.20 Hz, while the damping ratio is set to be 0.10, both as per
guideline. Hence: Mass M = Axle Loading/g-force and Spring Constant K = M (2πf)2 .
In general, the structures and track system have been analyzed for the passage of the THALYS
and ICE3M trains at velocities ranging from 160 to 360 km/h being 1.2 times the maximum design
velocity or line speed of 300 km/h, and from 160 to 264 km/h for the ICMAT train as its maximum
permitted vehicle speed lies at 220 km/h. An exception for the upper bound velocity is made for
the bridge across the Hollandsch Diep by reducing the factor of 1.2 to 1.1, resulting in a maximum
velocity of 330 km/h.
In the early stages of engineering the track system characteristics were not yet included in
the dynamic analyses. To study the favorable effects of the rails distributing the axle loadings in
longitudinal direction, a bell-shaped distribution was taken into account with a maximum spread
of 2.50 m. Structures with spans up to 20 m and structures with large cantilevered ends, of which
there are several in the HSL-Zuid project, show a reduction in the dynamic response. For structures
with spans larger than 20 m the effect of load distribution is found to be negligible.
The heart of the program is based on a Householder and QR-algorithm eigenvalue solution and
direct numerical integration using the Newmark β – Hilber α method. Depending on the structure’s
geometry there is a choice to construct 2-dimensional beam or 3-dimensional grid models, using
1-dimensional elements. The program contains a graphical interface and is able to directly transfer
data to MS-Excel for further processing. Special modules are included, dealing with shear deforma-
tion, rail level geometry and signal filtering by means of the Fast Fourier Transform method, which
is relevant for the criterion with regard to the maximum allowable, filtered structural accelerations.
where δini = + 1.5 mm and Li = 70.0 m for the end-spans and = 105.0 m between piers and a = the
distance along the bridge deck/track.
Dynamic aspects of the high-speed railway bridge across the Hollandsch Diep 173
105
V = 330 km/h
90 V = 300 km/h
V = 270 km/h
75 LIh limit value (45)
LIh value
60
45
30
15
0
-10.0 -7.5 -5.0 -2.5 0.0 2.5 5.0 7.5 10.0 12.5 15.0
Figure 10. The effect of systematic deformation of the rails on passenger comfort.
A second round of analyses was performed 2 years later in 2003, as part of the scope of Infraspeed,
to analyze the possible effects of the Rheda 2000® slab track system on the bridge structure and to
establish the final requirements with regard to the vertical rail level geometry.
The effect of rail roughness has been incorporated in more detail by combining actual field
data for short wavelengths, ranging from 3 to 25 m, with theoretical data for long wavelengths in
excess of 25 m (source: prof. C. Esveld, TU Delft). By use of a scaling factor it is possible to alter
the contribution of the long wavelengths to get in compliance with the required comfort level (see
paragraph 4.1). However, deviations from the starting value of 1.00 will have an impact on the level
174 Track-Bridge Interaction on High-Speed Railways
- 3 mm
Systematic Deformation
- 2 mm
Corrective Deflection/Pre-camber
of accuracy required during the final preparation of the vertical rail level and possibly requires a
closer monitoring of this level while the track is in operation.
Note that during the first dynamic analyses of the bridge, rail roughness effects were assumed
to be negligible due to the longs spans of the bridge, which resulted in a roughness factor equal to
1.00 according to formulae:
−L2 /100
froughness = 1 + 0.28e φ
where Lφ = the span of the bridge with a minimum of 42.5 m (at both ends).
In order to comply, the scaling factor for the bridge across the Hollandsch Diep had to be reduced
to 0.55 (see Fig. 12). For all other HSL-structures, analyzed for their interaction with the Rheda
2000® track system, scaling factors were found to be within a range of 0.92 to 1.12. This meant that
the preparation of the vertical rail level on the bridge would require more attention and accuracy
than at other structures, which was to be expected as this bridge structure was and still is the most
comfort sensitive structure in the entire HSL-Zuid project.
10.0
9.0
8.0
5.0
Vertical Rail Level [mm]
4.0
3.0
2.0
1.0
0.0
0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 160.0 180.0 200.0 220.0 240.0
-1.0
-2.0
-3.0
-4.0
-5.0
-6.0
-7.0
Location [m]
Figure 12. Vertical rail level geometry as applicable for the first 245 m on the bridge.
Figure 13. Graphical display of the bridge and train vertical displacements by program DRS.
176 Track-Bridge Interaction on High-Speed Railways
0.450
0.400
0.250
0.200
0.150
Bridge deck accelerations [m/s2]
0.100
0.050
0.000
0.0 100.0 200.0 300.0 400.0 500.0 600.0 700.0 800.0 900.0 1000.0 1100.0
-0.050
-0.100
-0.150
-0.200
-0.250
-0.300
-0.350
-0.400
-0.450
Location [m]
presence on the bridge the structure shows a response of maximum 0.04 times its dead load which
results to 11.0 kN/m (= 0.04 × 275 kN/m). Train load and structural response combined amounts
to 32.9 kN/m, which is considerably less than the uniform distribution load of 80.0 kN/m belonging
to Load Model 71 which is used in the static analyses. In general terms, the dynamic coefficient φr
results to 0.41 (= 32.9/80.0), thus less than 1.00. This approach however is only valid for structures
with large spans and a high ratio of dead load versus live load. For smaller structures, such as
viaducts the dynamic analyses showed higher φr -values, however hardly ever exceeding 1.67, the
upper bound value for coefficient φ2 .
Comparing both criteria with regard to the level of passenger comfort, the results show a strong
similarity between the LIh - and RMS-values, which is obvious as they are based on the same
principles. In the case of the bridge across the Hollandsch Diep the ratio LIh over corresponding
RMS-value results to 111, i.e. for a RMS-value of 0.525 m/s2 the corresponding LIh -value = 58.3.
See also Figure 15.
In the worst case scenario, combining systematic deformation and corrective deflection or pre-
camber [SDCD] a maximum LIh -value of 52 is derived. According to Figure 7, the number of
100% satisfied passengers would reduce from 84% to 78%, while the number of 100% unsatisfied
passengers almost remains steady at 10%. Due to the fact that the conditions for which the maxi-
mum calculated systematic deformations occur are rare, the level of passenger comfort is only
compromised for short periods of time and then only in certain areas of the train as can be seen
in Figure 16. Most of these areas coincide with the axle positions of the locomotive sections. As a
consequence of these arguments, the increase of the LIh -value from 45 to 52 has been acknowledged
by the HSL-Zuid Project-organization.
When both approaches for the level of passenger comfort are being compared, it could be
concluded that the criteria for the structure are more strict than those applicable to the track system.
However, the effects of vertical rail imperfections or rail roughness (short and long wavelengths)
have not been taken into account during the first dynamic analyses concerning the structure as
Dynamic aspects of the high-speed railway bridge across the Hollandsch Diep 177
0.700
75.0
0.650 [PA] [RMS] [CD] [RMS]
70.0
[SDCD] [RMS] [CDRGF055] [RMS]
0.600
65.0
[SDCDRGF055] [RMS] Upper Limit RMS-value
0.550
[PA] [LIh] [CD] [LIh] 60.0
Maximum RMS trainaccelerations [m/s ]
2
45.0
LIh values
0.400
40.0
0.350
35.0
0.300
30.0
0.250
25.0
0.200
20.0
0.150
15.0
0.100
10.0
0.050 5.0
0.000 0.0
160.0 170.0 180.0 190.0 200.0 210.0 220.0 230.0 240.0 250.0 260.0 270.0 280.0 290.0 300.0 310.0 320.0 330.0
Figure 15. Maximum RMS train accelerations and LIh -values for governing train type ICE3M2.
0.700
75.0
0.650
70.0
0.600 ICE3M2 [CD] ICE3M2 [SDCD] ICE3M2 [SDRCD]
65.0
0.550 THALYS2 [CD] THALYS2 [SDCD] THALYS2 [SDRCD] 60.0
RMS train acceleration [m/s2]
0.500 55.0
0.450 50.0
0.400 45.0
LIh value
40.0
0.350
35.0
0.300
30.0
0.250
25.0
0.200
20.0
0.150
15.0
0.100 10.0
0.050 5.0
0.000 0.0
0.0 50.0 100.0 150.0 200.0 250.0 300.0 350.0 400.0
Figure 16. Maximum train acceleration for each axle-position types THALYS2 and ICE3M2.
178 Track-Bridge Interaction on High-Speed Railways
they were nullified by the definition of the roughness factor. The RMS-range from 0.470 m/s2 ,
corresponding with a LIh -value of 52, to 0.525 m/s2 is used to allow for a, however reduced (scaling
factor = 0.55), realistic vertical rail level geometry in the Rheda 2000® track system analyses.
As a result of the first dynamic analyses performed on the bridge across the Hollandsch Diep an
alternative for the LIh -criterion was introduced in the way of a maximum allowable vertical train
acceleration of 0.70 m/s2 valid for structures with 3 or more repetitive spans in a row. The value of
0.70 m/s2 coincides with a LIh -value of 45 ms−5/3 and takes out the dependency on the duration of
passage in the LIh approach.
Another important issue is the impact of the vertical rail level geometry on the axial forces in
the rail-fastenings and the bending moments in the rails. In general, the forces in the rail-fastenings
are of a higher importance as the fastenings are the weaker link in the system. During a quasi-static
passage of train ICE3M the benchmark values are established at 3.0 kN for the tensile (upward)
forces and −36.3 kN for the compression (downward) forces in the fastenings. See Figure 17. The
THALYS and ICMAT trains show similar results, all in proportion to the maximum axle loading of
170 kN for ICE3M and THALYS and 225 kN for ICMAT (see Fig. 8), and in combination with a
center-to-center sleeper distance of 600 mm to 650 mm. Hence, a pair of rail-fastenings or a sleeper
location is subjected to approximately 45% of the axle loading. This is a recurring result for all
HSL-structures analyzed and shows that the distribution of a single axle loading covers at least 3
but most probably 5 sleeper locations.
The systematic deformation [SD] of the vertical rail level has a minor effect which is only
noticeable for the compression forces in the rail-fastenings (see Figure 17). More relevant is the
rail roughness effect [RGF055] which results in an amplification of both tensile and compression
forces. However, the component of the long wavelengths in this signal, has a minor to negligible
impact on the results, which seem to be solely dictated by the short wavelengths. A plausible reason
for this fact is that the frequency range of these short waves, especially at high train velocities, lies
much closer to the natural frequencies of the track system.
40.0
30.0
20.0
10.0
0.0
0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 160.0 180.0 200.0 220.0 240.0
-10.0
Axial Forces in (2) Fastenings [kN]
-60.0
-70.0
-80.0
-90.0
-100.0
-110.0
-120.0
Location [m]
Figure 17. Rail fasting forces in first 240 m of BHD during the passage of train ICE3M(2).
Dynamic aspects of the high-speed railway bridge across the Hollandsch Diep 179
In the design of the rail-fastening system, limitations to the allowable tensile forces have been
formulated and a minimum dynamic coefficient φ2 of 1.67 has been incorporated. In the worst case
scenario, combining rail level situations [SD] and [RFG055], the dynamic coefficient φr for the
rail fastenings in compression amounts to 1.62. However, due to the application of a pre-camber in
the rail level this value is reduced to 1.50. In those areas where the tensile forces in the fastening
systems may exceed the allowable values, special fastenings with a higher capacity for tensile
forces have been applied. This is especially valid at the dilatations between the smaller structures
in the HSL-track, where differential vertical displacements and rotations are likely to occur. At
the bridge across the Hollandsch Diep, these effects have been reduced by the implementation
of steel transition slabs to keep the dynamic amplification of the forces and bending moments in
rail-fastenings and rails within the required limits.
635 2380
200
232
500
40
2700
Expansion/Contraction Area
100
Figure 18. Steel transition slab connecting bridge with approach ramps.
180 Track-Bridge Interaction on High-Speed Railways
rail(s)
rail-fastening
spring and damping characteristics
transition slab
mass, flexural and damping characteristics
transition slab supports
1500 mm
stiffness and damping characteristics
CL track
Figure 20. 1st and 2nd mode shape of transition slab at 37 and 59 Hz respectively.
Special provisions are taken with regard to the horizontal fixation of the slab, perpendicular to
the track and the proper guidance of the slab in longitudinal direction. A steel U-shaped section is
bolted down to the slab in the center of track, in line with the concrete derailment provision on the
bridge and approach ramps.
40.0
27.5
K =1000 MN/m, Dratio = 0.005
25.0
K =1000 MN/m, Dratio = 0.020
22.5 K =1000 MN/m, Dratio = 0.050
20.0
17.5
15.0
12.5
10.0
7.5
5.0
2.5
0.0
160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330
Train velocity [km/h]
Figure 21. Maximum uplift support forces versus train velocity, during passage of ICE3M(2) train.
such that the filtered, structural accelerations would not comply with the design criteria, while in
upward motion the dynamic forces at the supports would overcome the static forces due to dead
load, resulting in loss of contact. This is an undesirable effect with regard to the support’s capacity to
withstand fatigue. By introducing a design with a higher stiffness-mass ratio the natural frequency
of the combined system (rails, fastenings, transition slab and supports) has been increased. In
general, the filtered vertical structural accelerations will decrease with an increase of the system’s
natural frequency. At the same time, the increase of mass works out positively as a measurement
to reduce uplift.
From test results the vertical (secant) stiffness of the supports was established which ranged
between 380 and 1125 MN/m, depending on the frequency of the applied load and the number of
load cycles. The natural frequency of the system largely depends on the support stiffness and ranges
from 37 to 54 Hz (1st mode shape, see Fig. 20) within the established range of support stiffness.
These results have been obtained for the situation where the supports are located in the outer position
(see also Fig. 18), hence when the bridge-structures is fully contracted. This is considered to be
the governing situation, creating the largest span and consequently the lowest natural frequency
possible.
Due to the increase of natural frequency, the filtered vertical accelerations have been reduced to a
maximum value of 0.24 g. The unfiltered results however, show values exceeding 1.00 g. Although
these values occur at the center of the track and show a decrease towards the supports, the possibility
of a temporary uplift, has been thoroughly investigated.
In Figure 21, the impact of the support stiffness (selected values: 250, 500 and 1000 MN/m)
and damping ratio (selected values: 0.005, 0.020 and 0.050) is shown for the uplift support forces
during the passage of the governing train type ICE3M(2). With the increase of the support stiff-
ness, the position of the peak values for the uplift forces shift to higher train velocities, without
showing a severe reduction nor increase in value. As to be expected, the support damping provides
a considerable reduction of these peak values. Within the stiffness range of 250 to 1000 MN/m, a
damping ratio of 0.050 (5% of the critical damping) reduces the uplifting support forces to 50–60%
182 Track-Bridge Interaction on High-Speed Railways
30.0
20.0
10.0
Support Forces [kN]
0.0
0.000 0.500 1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500 5.000 5.500
-10.0
-20.0
-30.0
-40.0
-50.0
-60.0
-70.0
Time [s]
Figure 22. Time-history of support forces during passage of ICE3M(2) at 290 km/h.
of the support forces due to the dead load of the system, which is 30 kN per support. This results
in a minimum safety factor against uplift of 1.67.
Having adapted the design of the transition slab with the restriction of uplifting forces at the sup-
ports in mind has also been beneficial to the requirements with regard to the dynamic coefficients,
the level of passenger comfort and the forces in the rail-fastenings as they do not reveal anything
out of the ordinary. The dynamic bending moments in the transition slab remain below the static
bending moments derived during the passage of static load models LM71 and SW2. This results
in a dynamic coefficient φr below unity. Due to its short determinant length [Lφ ] coefficient φ2 is
governing with a value of 1.67. The upward dynamic response of the steel plate is compensated by
its dead weight. In a conservative approach of the passenger comfort, the governing RMS-value of
the vertical train accelerations is established at 0.290 m/s2 , hence below the maximum allowable
value of 0.525 m/s2 . The dynamic amplification factor of the forces in the rail fastenings does not
exceed 1.40.
In Figure 22, the time-history results for the support forces are shown during the passage of train
type ICE3M2 at a velocity of 290 km/h, with a support stiffness of 500 MN/m and a damping ratio
of 0.050. The characteristics of the train, axle positions and loading effects (2 times 8 wagons with
4 axles each) are clearly recognizable.
Out of the ordinary structures, especially small sized structures such as these transition slabs,
combining a lot of different functions on a concentrated area, often require more attention than
usual and may create more questions than answers.
The basic design principle of these transition slabs had already been applied and proven itself
before in HSR tracks abroad. New, however were the operational train velocity, the train charac-
teristics and the depth of the dynamic analyses. Coming up with a workable solution proved to be
an interesting engineering challenge.
7 CONCLUSION
The structures in the HSL-Zuid project generally show natural frequencies in the range of 3 to
10 Hz. Usually, the governing dynamic criteria for this type of structures are the (filtered) structural
accelerations, which depend on span length, type and velocity of passing train and the presence
of cantilevered ends. The THALYS train for instance shows governing results for spans between
16 and 20 m, while the ICE3M train shows governing results for spans just over 20 m. Passenger
comfort becomes an issue for structures with considerably larger spans, certainly in situations
where there are 3 or more similar spans in a row.
Dynamic aspects of the high-speed railway bridge across the Hollandsch Diep 183
Figure 23. Transition slab just hoisted into position. (Photo, courtesy of Mr. P. Meijvis, DMC bv, The
Netherlands).
Figure 24. Rheda 2000 slab track system on bridge across the Hollandsch Diep. (Photo, courtesy of
Mr. P. Meijvis, DMC bv, The Netherlands)
184 Track-Bridge Interaction on High-Speed Railways
One of the largest structures in the HSL-Zuid project, the bridge across the Hollandsch Diep
and one of the smallest structures, the transition slab covering the expansion areas of this bridge,
have in common that their dynamic behavior has played a considerable factor in their final design.
Considering the many dynamic analyses performed on other HSL- structures, these structures have
shown features which were out of the ordinary.
The low natural frequency of the bridge across the Hollandsch Diep of 1.10 Hz makes this
structure relative insensitive to the dynamic impact of real train loads, resulting in low structural
accelerations. However, trains with natural body frequencies ranging between 0.8 to 1.6 Hz are
easily exited, herewith compromising the required level of passenger comfort. Several measures
were taken to keep the passenger comfort within and acceptable level, of which one has been the
application of a pre-camber in the vertical rail level during the installation of the Rheda 2000 slab
track system. The bridge-structure and the track system are subject to different comfort criteria.
The more severe criterion for the bridge structure allows for a better approach of the rail roughness
impact in the design of the track system. However, for the sake of clarity both criteria should merge
into one.
The transition slab is a structural element with a relative high natural frequency. Sliding over the
4 supports but not vertically fixated the main problem here lies in the possible loss of contact which
is not beneficial to the fatigue strength of the supports. By increasing the stiffness over mass ratio
and establishing the damping properties of the sliding PE-elements in the supports, the (filtered)
structural accelerations of the transition slab and the uplift forces in the supports are kept within
acceptable limits.
REFERENCES
High Speed Line – South project guidelines HSL600E “Loads and Deformations on HS-structures”, 1999.
EN 1991-2: Eurocode 1, “Actions on structures – Part 2: Traffic loads on bridges”, 2003.
“Dynamics of Railway Bridges”, Ladislav Fryba (ISBN: 0-7277-2044-9), 1996.
“Structural Dynamics by Finite Elements”, William Weaver Jr., Paul R. Johnston (ISBN: 0-13-853508-6),
1987.
“Finite Element Procedures”, Klaus-Jürgen Bathe (ISBN: 0-13-301458-4), 1996.
CHAPTER 15
A.J. Reis
Technical University of Lisbon & GRID SA, Lisbon, Portugal
ABSTRACT: The concept design for long railway bridges shall take into consideration the need to
balance imposed deformations of the deck, due to thermal effects, shrinkage and creep in concrete
and composite structures and induced stress effects in the rails. The need to reduce the number of rail
expansion devices requires moderate lengths of continuous superstructures and so the introduction
of expansion joints in the deck. In seismic zones, the concept design of the bridge shall balance the
advantage of short continuous lengths of the superstructure, to reduce track-structure interaction
effects, with the inconvenient of transferring the seismic forces to a limited number of piers. The
bridge design shall take into consideration a variety of other variable actions inducing stresses in the
rails due to longitudinal displacements, namely associated to braking forces and vertical actions.
Due to the continuity of the rails on the structural expansion joints, the deformations of the deck
induce stresses in the rails that need to be checked. The main design criteria are now specified in
Eurocode 1-Part 2. The concept design for two long railway bridges, located in seismic zones, is
discussed in the present paper. Prestressed concrete and steel-concrete composite superstructures
are considered. To check track-structure interaction, a numerical model based on EC1-Part 2 and
UIC 774-3 was developed and results are presented for one of these viaducts.
1 INTRODUCTION
In concept design of long railway bridges (above 400 m) one of the main constraints is the track-
structure interaction, i.e. the concept design of the track itself.
The ballasted continuous track is very popular among the track owners, since they can avoid
introduction of rail expansion devices, and so, reduce track maintenance costs. On the other
hand, the maintenance of ballasted tracks is a very well known problem and track owners have
large experience on dealing with it. Although, this concept applied to long viaducts raises several
problems regarding the track-structure interaction, namely the effect of structural deformations on
rail stresses.
This is not a specific problem of the High Speed Railway bridges, so from this point of view,
there is no difference between HSR bridges and conventional railway bridges.
Generally, regular bridges without special constraints, can be conceived for continuous ballasted
track, adopting short spans and as many structural expansion joints as needed, but when other
important structural constraints are imposed, such as topographical, geotechnical and seismic
constraints, the structural design may prevail.
This paper focus particularly on the design of two solutions for long railway bridges in similar
environment, but with two different solutions to solve the track-structure interaction problem.
The bridges are inserted in the same track stretch of the Portuguese south railway line, linking
Lisbon to Algarve, but have slightly different ground conditions, and both are implanted in a seismic
area. In this stretch, the design speed is 220 km/h.
185
186 Track-Bridge Interaction on High-Speed Railways
Access Viaducts
São Martinho
North South Viaduct
One of the design solutions was adopted in both approach viaducts – North and South – to the
new bridge over river Sado, at Alcácer do Sal. The other solution refers to the São Martinho viaduct,
a few kilometres towards north from the Sado crossing (Table 1).
2 BASES OF DESIGN
A significant part of the total length of the viaduct was implanted over very thick alluvial deposits,
imposing deep pile foundations (20–30 m).
Despite the high deformability of the foundations, it was possible to maintain the continuity of
the rail track without any expansion device, mobilizing a total of 4 stiff piers in each viaduct seg-
ment, that are responsible to control structural deformations and ensure track safety requirements
(Figure 3).
3 SEISMIC DESIGN
4 TRACK-BRIDGE INTERACTION
4.1 Introduction
Continuous tracks when crossing support discontinuities, such as embankment-bridge transitions,
or structural expansion joints, transmit horizontal forces directly applied to the support, which have
a stiffness discontinuity, producing stresses concentration in the rails.
Figure 5. Approach viaducts to the new Bridge over Sado River (South). Composite steel-concrete deck, approx. 1100 m total length. Double plated steel girders section,
with tubular diaphragms. Total width varying between 13 m and 15.7 m. Double track.
Track-structure interaction in long railway bridges 191
Figure 6. Particular Solution for south part of São Martinho Viaduct. Connections with dampers.
In the same way, where continuous rails restrain the free movement of the bridge deck, deform-
ations of the bridge deck (e.g. due to thermal variations, vertical loading, creep and shrinkage)
produce longitudinal forces in the rails and in the fixed bridge bearings.
The effects resulting from the combined response of the structure and the track to variable
actions shall be taken into account for the design of the bridge superstructure, fixed bearings, the
substructure and for checking load effects in the rails.
The next specifications, based on section 6.5.4 of EN 1991-2:2003 are valid for conventional
ballasted tracks, which is the design case to be discussed.
When determining the combined response of track and structure to traction and braking forces,
the traction and braking forces should not be applied on the adjacent embankment unless a complete
analysis is carried out considering the approach, passage over and departure from the bridge of rail
traffic on the adjacent embankments to evaluate the most adverse load effects.
– Compression: 72 N/mm2 ;
– Tension: 92 N/mm2 .
The above given limiting values are valid for tracks complying with:
In the viaducts to be discussed, all the above criteria are satisfied. When any of the criteria is
not satisfied special studies should be carried out or additional measures provided.
– 5 mm for continuous welded rails without rail expansion devices or with a rail expansion device
at one end of the deck,
– 30 mm for rail expansion devices at both ends of the deck where the ballast is continuous at the
ends of the deck,
– movements exceeding 30 mm shall only be permitted where the ballast is provided with a
movement gap and rail expansion devices provided.
Where δB is:
– the relative longitudinal displacement between the end of a deck and the adjacent abutment or,
– the relative longitudinal displacement between two consecutive decks.
Due to vertical traffic actions up to two tracks loaded with load model LM 71 (and where required
SW/0) δB shall not exceed the following values:
– 8 mm when the combined behaviour of structure and track is taken into account (valid where
there is only one or no expansion devices per deck),
– 10 mm when the combined behaviour of the structure and track is neglected.
– the longitudinal displacement of the upper surface of the deck at the end of a deck due to
deformation of the deck.
194 Track-Bridge Interaction on High-Speed Railways
5.1 Principles
For the determination of load effects in the combined track/structure system a model based upon
Figure 8 (from EC1, part 2: EN 1991-2:2003) was used.
The longitudinal load/displacement behavior of the track or rail supports may be represented by
the relationship shown in Figure 9 (from EC1, part 2: EN 1991-2:2003) with an initial elastic shear
resistance [kN/mm of displacement per m of track] and then a plastic shear resistance k [kN/m of
track].
The diagrams (4) and (6) were adopted, with the following values (from UIC 774-3):
Loaded track (4): k = 60 kN/m, u0 = 2 mm
Unloaded track (6): k = 20 kN/m, u0 = 2 mm
For the design case to be discussed there will be a change in the future from one way/track to
two way/track use. Hence all cases are taken in account.
For the calculation of the total longitudinal support reaction FL and in order to compare the
global equivalent rail stress with permissible values, the global effect is calculated as follows:
FL = ψ0i Fli (1)
with:
Fli The individual longitudinal support reaction corresponding to the action i;
ψ0i For the calculation of load effects in the superstructure, bearings and substructures the
combination factors defined in EN 1990 A2 shall be used;
ψ0i For the calculation of rail stresses, ψ0i shall be taken as 1.0.
When determining the effect of each action, the non-linear behaviour of the track stiffness shown
in Figure 9 should be taken into account. The “k” value depends if the track is loaded or unloaded.
This means that for each loading, a different computer model has to be calibrated, according to the
loaded and unloaded positions of the track.
The longitudinal forces in the rails and bearings resulting from each action may be combined
using linear superimposition.
– deck,
– piers,
– piles,
– track.
The computer model simulates the entire viaduct and also an additional of 300 m (from each
side of the viaduct) of track in the ground, above the backfill.
All the 7 independent frames were included in the computer model (7 × 4 × 28.4 +
1 × 2 × 28.4 = 852 m), according to the general principles of modelation and the global structural
model.
The connection between the track and the structure was modelated by elements with nonlinear
response (as defined above), and each frame element has 1 m length, in general.
Figure 9. Variation of longitudinal shear force with longitudinal track displacement for one track.
196 Track-Bridge Interaction on High-Speed Railways
Figure 10. Track-structure analysis model, including the backfill of the north abutment and the first 5 spans.
– u0 = 2 mm,
– Track-structure plastification force:
Loaded track (4): k = 60 kN/m,
Unloaded track (6): k = 20 kN/m,
The track and the nonlinear modelation were extended to both sides of the structure of the
viaduct, to take into account the track on the ground, admitting the soil rigid, as defined in EC1.
On Figure 10, one show the analysis model, between the piers P1 and P5, where are modelated:
– the foundations,
– the track over the deck,
– the track over de terrain.
In this section, there are already discontinuities between the deck and the abutment (where the
structure begins) and over the pier P4 (with doubling of nodes on top), being the track, and his
connections, continuous.
Four braking positions and six traction positions were modelated, with the purpose of investi-
gating the most unfavorable position for these actions. It was concluded that the most unfavorable
effect for the tracks occur where discontinuities in the structure exist, due to differential displace-
ments. There are differential displacements imposed to the structure that the track has to follow,
and the load positions try to maximize this effect.
The actions in the modelations were (following EC1-part2):
In Figure 11 are shown the traction and braking position forces adopted.
In Table 2 one list the most unfavorable stresses obtained for two critical sections of the track:
near the abutment (at the expansion joint) and at the expansion joint between two different frame
decks (at the intermediate piers). The safety check of the track is made according to EC1-2 for the
maximum additional compression stress in the track, due to this action (Table 3).
For the deformation check of the structure, due to traction and braking actions, this type of
analysis, based in a track-structure interaction, allows to check the limit defined in EC1-2 of 5 mm.
On Table 4 one presents the results for each loading case and also the combined value of the
displacement.
Figure 11. Track-structure interaction model: localization scheme: traction actions (Axx) and breaking actions (Fxx).
198 Track-Bridge Interaction on High-Speed Railways
Table 3. Track verification. Security Check (4 rails > 550 × 4 = 2200 kN).
Zone mm
Abut. N 2.1 0.0 0.1 0.0 0.8 0.0 0.0 0.0 0.0 0.1 2.1 0.8 2.9
P04 – N 2.2 0.0 0.1 0.1 0.6 0.0 0.0 0.0 0.0 0.1 2.2 0.6 2.8
P04 – S 2.5 0.0 0.3 0.5 0.2 0.2 0.0 0.0 0.0 0.3 2.5 0.3 2.7
P08 – N 2.4 0.0 0.4 0.6 0.1 0.2 0.0 0.0 0.0 0.3 2.4 0.3 2.7
P08 – S 1.8 0.0 1.6 2.2 0.0 0.8 0.0 0.0 0.0 0.8 2.2 0.8 3.0
P12 – N 1.6 0.0 1.7 2.2 0.0 0.8 0.0 0.0 0.0 0.7 2.2 0.8 3.0
P12 – S 0.4 0.2 2.6 2.6 0.0 0.2 0.0 0.1 0.2 0.2 2.6 0.2 2.8
P16 – N 0.3 0.2 2.6 2.5 0.0 0.1 0.0 0.1 0.2 0.1 2.6 0.2 2.7
P16 – S 0.1 0.9 2.7 2.1 0.0 0.0 0.0 0.4 0.8 0.0 2.7 0.8 3.6
P20 – N 0.1 1.0 2.7 2.0 0.0 0.0 0.0 0.5 0.9 0.0 2.7 0.9 3.6
P20 – S 0.0 2.4 0.7 0.4 0.0 0.0 0.0 0.8 0.4 0.0 2.4 0.8 3.2
P24 – N 0.0 2.4 0.6 0.4 0.0 0.0 0.0 0.7 0.3 0.0 2.4 0.7 3.1
P24 – S 0.0 2.4 0.1 0.1 0.0 0.0 0.1 0.2 0.1 0.0 2.4 0.2 2.6
P28 – N 0.0 2.3 0.1 0.1 0.0 0.0 0.1 0.1 0.1 0.0 2.3 0.1 2.4
P28 – S 0.0 0.3 0.0 0.0 0.0 0.0 0.1 0.0 0.0 0.0 0.3 0.1 0.5
Abut. S 0.0 0.2 0.0 0.0 0.0 0.0 0.1 0.0 0.0 0.0 0.2 0.1 0.2
7 CONCLUSIONS
A discussion on track-structure interaction for long railway bridges was presented. The problem
of imposed deformations and seismic actions were discussed taking into consideration the need
to “balance” the continuity of the structure with the requirements for minimum track expansive
joints.
A design case was presented according to the Eurocodes, namely in terms of actions and in terms
of structural safety verification.
The stress analysis allows concluding that the limit stress on the rail is almost reach out, for
compression, being, in general, the piers joints the most unfavorable. Although, the braking force
produces higher stresses near the abutment joint, due to absorption of this force in the backfill of
the abutments.
Track-structure interaction in long railway bridges 199
Figure 12. Track axial force diagram due to temperature (structure heating).
Figure 13. Track axial force diagram due to braking (maximum stress near the abutments).
Figure 14. Track axial force diagram due to braking (maximum stress near intermediate pier).
Besides, for compatibility of displacements, the temperature generates higher stresses on the
track near the piers joint (there is a higher displacement amplitude).
The vertical forces, in this model, were not critical, and induce very low stress amplitude.
The displacement limit of 5 mm, was also verified with some clearance.
In conclusion, the track interaction analysis allowed to check the track safety, in terms of
Eurocodes criteria, for a joint distance larger than 90 m, although in this situation, the length
of 4 × 28.4 = 113.6 m is almost at the allowable limit for stress verification.
200 Track-Bridge Interaction on High-Speed Railways
ACKNOWLEDGEMENTS
Thanks are due to REFER for allowing the publication of some results of specific studies developed
for the design of the new stretch of the Portuguese south railway line, near Alcácer do Sal, that
includes the New Sado River railway crossing.
REFERENCES
EN1991-2, Actions on structures – Part 2: General actions – Traffic Loads on Bridges, European Committee
for standardization, CEN (2003).
UIC Code 774-3-R, “Track/bridge interaction – Recommendations for calculations”, 2nd edition, October
2001, Union International des Chemins de Fer, UIC, 2001.
CHAPTER 16
ABSTRACT: The present work deals with the phenomenon of track-deck interaction in rail-
way bridges. Following a brief description of the methodology of analysis and the safety checks
established in the most recent European regulations on this matter (EN1991-2), an application is
presented regarding the study of the bridge over the river Moros, a 476,0 m long continuous deck
bridge with a box type of cross section, designed to operate in the Segóvia – Valladolid high-speed
railway line.
1 INTRODUCTION
One of the fundamental aspects to take into account in the conception and design of railway bridges
refers to the effects resulting from the track-deck interaction.
The demands currently faced by modern railway lines have led to the adoption of continuous
welded rail (CWR), towards a reduction in maintenance efforts and an increase in the level of
comfort of the passengers.
When a rail is placed continuously over a bridge or viaduct, both structures have to resist to the
loads resulting from temperature variations, from the traction and/or braking of the trains, from
creep and shrinkage of the deck, which produce efforts in the rails and forces in the supports of
the deck.
The effects resulting from the combined response of the bridge and the track to these loads
should be taken into account not only in the design of the structural elements, but also in the check
of the stress state in the rails and of the deformations of the structure, in order to ensure the stability
of the track and thus guarantee the safety of circulation [1, 2, 3, 4].
The procedures related with the determination of these effects were included in the latest version
of EN1991-2 [5] which reflects the most recent research carried out in this field.
In the present work, after a brief description of the methodology of analysis and the safety checks
established in the referred regulation, its application is presented to the study of the bridge over the
river Moros, a 476,0 m long continuous deck bridge with a box type of cross section, designed to
operate in the Segóvia – Valladolid high-speed railway line. This study involves a sensitivity analy-
sis in relation to the parameters that influence the combined response of the track and the structure,
namely the length of the zone of track in embankment and the stiffness of the abutment/foundation
group.
2 ANALYSIS METHODOLOGY
2.1 Introduction
In 2001, sheet UIC 774-3R [6] was published, reflecting the works of the expert committee D213
of ERRI on the effects of the track-deck interaction in railway bridges. The recommendations
201
202 Track-Bridge Interaction on High-Speed Railways
on this sheet were mostly entirely transferred to the EN1991 2 standard, under a section entitled
“Combined response of structure and track”. In this section, the loads and respective combinations
to consider are specified, as well as the methods of structural models of the track-bridge system
and the safety criteria to be adopted.
2.2 Loads
According to EN1991-2, for the assessment of the effects of the track-bridge interaction the follow-
ing loads should be taken into account: (i) vertical train loads; (ii) longitudinal forces resulting from
starting or braking of the trains; (iii) uniform or differential temperature changes; (iv) shrinkage
and creep of the concrete.
The vertical permanent or transient loads to be applied are translated by the LM71 (and SW/0
or SW/2) load model. The longitudinal forces resulting from starting or braking are provided by
the following expressions:
i) starting forces:
QLak = 33 [kN/m] × La,b [m] ≤ 1000 [kN], for load models LM71, SW/0 and SW/2;
ii) braking forces:
QLbk = 20 [kN/m] × La,b [m] ≤ 6000 [kN], for load models LM71and SW/0;
QLbk = 35 [kN/m] × La,b [m], for load model SW/2.
The characteristic values of the uniform temperature variation in the track and the deck, according
to sheet UIC774-3R and EN1991-2, can be taken equal to ±50◦ C and ±35◦ C, respectively. The
characteristic values and the distribution of the differential change in temperature in the cross-
section are defined in the pre-standard prEN1991-1-5 [7] as a function of the deck typology and
of the upper coating. In what concerns the retraction or creep of the concrete, the effects to be
considered will depend on the time lag between the construction of the deck and the installation of
the track.
1 2 3
5 5
4 6
Figure 1. Simplified structural model for the analysis of the effects of the track-deck interaction (adapted
from [6]).
Track-bridge interaction in railway lines 203
The longitudinal behaviour of the track-deck connection can be modelled as a spring which
behaviour is translated by a load/displacement relation similar to that illustrated in Figure 3, that
is, a bi-linear relation consisting of an initial elastic section up to a relative displacement u0 and a
section corresponding to the plastification of the connection for a load of value k, given in kN/m
per metre of track length.
For the case of a ballasted track, u0 is equal to 2 mm and k takes the values of 20 or 60 kN/m
per metre of track development, whether the track is unloaded or loaded, respectively.
Hence, the effects of the track-deck interaction have to be derived by means of a non-linear
analysis of the system. In accordance with EN1991-2, the total effects may be determined by linear
superposition of the effects obtained for each of the loads acting individually. The total normal
stress in the rails, or the total longitudinal reaction in the supports, can then be obtained by means
of the expression:
FL = (ψ0i · FLi ) (1)
where FLi is the effect of load i and 0i is the combination coefficient relative to load i, which
values are defined in EN 1990-A2 [8].
For the calculation of the normal stress in the rails, the combination coefficients should be
considered equal to 1.0.
rail axis
Longitudinal non-linear spring Und Longitudinal non-linear spring
efo
rma
ble
bar
Un
Z Z
for
ma
ble
ba
r
Fixed support
X Y
Figure 2. Location in height of the elements corresponding to the rails, the deck and the supports (adapted
from [6]).
k [kN/m/m of track]
Longitudinal shear force in track per unit length,
1500 m, fixed to concrete sleeper with a spacing of 0.65 m or less, over a consolidated ballast layer
with a minimum thickness of 0.30 m, have demonstrated that the normal stress in these elements,
for the combined action of diverse loads, should not exceed the following values:
a) 72 N/mm2 , in compression;
b) 92 N/mm2 , in tension.
In terms of the structure displacements, the following limits should not be exceeded:
i) due to starting and braking, the relative longitudinal displacement between the end of the deck
and the abutment, or the relative longitudinal displacement between two consecutive spans
of the deck, δB, should not go above 5 mm, for the case of a continuous welded rail (CWR)
without dilation devices or with one dilation device in one of the ends of the deck, and 30 mm,
for the case of a deck with dilation joints in the rails at both ends and a continuous ballast layer
over those ends;
ii) due to vertical loads, the longitudinal displacement of the upper surface of the deck in its end,
δH, should not exceed 8 mm when the composite behaviour of the track and the structure is
taken into account, and 10 mm when that composite behaviour is ignored;
iii) furthermore, the vertical displacement of the upper surface of the deck in relation to the adjacent
structural element (abutment or span of the deck), δV, should not exceed 3 mm, for maximum
speeds on site of 160 km/h, and 2 mm, for maximum speeds greater than 160 km/h.
3.1 Description
The bridge over the river Moros, designed to operate in the Segóvia – Valladolid high-speed railway
line, is composed by a continuous deck with total length of 476.0 m, consisting of seven intermediate
spans of 56.0 m and two end spans of 42.0 m (Fig. 4). Longitudinally, the deck has a fixed support
(AF) located over the abutment E1, while the remaining supports are mobile (AM). The track
exhibits one dilation device (AD) at the end of the deck adjacent to abutment E2.
The deck, of pre-stressed reinforced concrete, presents a box type of cross-section and its
geometry is represented in Figure 5, serving as support to two railway tracks (V1 e V2).
The track is composed of UIC60 rails placed over concrete sleepers, spaced between them by
0.60 m, positioned on top of a ballast layer with a minimum thickness of 0.35 m under the sleep-
ers. The outline at the bridge site presents a longitudinal gradient of 0.21%, with a plan radius of
11 444 m.
3.2 Modelling
In Figure 6 is illustrated the finite element model developed for the analysis of the track-deck
interaction. The deck has been discreetized by means of beam elements with the following
characteristics: elasticity modulus E = 35 GPa; section A = 11.19 m2 ; moment of inertia
I = 28.82 m4 and thermal dilation linear coefficient αC = 1.0 × 10−5 /◦ C.
Each of the tracks was modelled by means of beam elements placed in the alignment of the
respective axles. An extension of the track has been modelled corresponding to the length of the
z[m]
REJ
Track
892m
890
880 FR FR FR FR FR FR FR FR FR FF
Moros River x[m]
870 862m
860
850
deck and 300.0 m to the side of the abutment E1 in order to simulate the track over the adjacent
embankment (Fig. 6a)). The characteristics of these elements correspond to two UIC 60 rails, that
is: elasticity modulus E = 210 GPa; section A = 0.0153 m2 ; moment of inertia I = 6.11 × 10−5 m4 ;
thermal linear dilation coefficient α = 1.2 × 10−5 /◦ C.
The connection between the elements of the track and of the deck, and between the elements
of the deck and the supports was simulated by means by rigid bars (Fig. 6b)). The elements that
model the track-deck connection, with non-linear behaviour translated by the relation presented in
Figure 3, were placed at a height corresponding to the base of the sleepers.
As previously mentioned, the deck is supported by the E1 abutment by means of a fixed support.
The stiffness of the elastic support corresponding to the abutment/foundation group was determined
based on a model using volume finite elements (Fig. 7) where the elasticity moduli for the foundation
soil and the abutment were considered to be Es = 190 MPa and Ec = 25 GPa, respectively, from
which k = 660 × 103 kN/m was obtained. In order to assess the influence of the group stiffness,
other situations were also analysed corresponding to stiffness values equal to 330 × 103 kN/m
(0.5 k), 3300 × 103 kN/m (5 k) and infinite stiffness, that is, deck fixed to the support.
The influence of the track length in the embankment zone beyond the E1 abutment was also
analysed for the k = 660 × 103 kN/m scenario, and lengths of 100 and 200 m were considered,
besides the 300 m.
0.30
N.A.
0.30
z [ m]
a)
0.73
3.00 3.00
2.75 1.64
5.23
N.A.
4.50
0.73
3.00 3.00
0.10
1.76 1.76
1.64
N.A.
2.75
E1
b) c) d)
Figure 6. Structural model of the track-deck system: (a) front view; (b) cross section of the support; (c) cross
section of the span and (d) detail of the model at the zone of the fixed support.
206 Track-Bridge Interaction on High-Speed Railways
i) the stiffness of the abutment/foundation group has great influence in the values of the normal
stress on the rails and of the support reactions;
ii) for the LM71 load model, the maximum tensions on the rails occur over the fixed support E1;
iii) for an uniform temperature variation loading, the compressions on the rails at the abutment
E1 vary according to the stiffness of the abutment/foundation group;
iv) for a loading considering the LM71 load model and an uniform temperature variation, the
increase of the stiffness of the abutment/foundation group results in an increase of the normal
stresses in the rails and of the support reactions;
v) for starting and braking loading, the maximum stresses (compression or tension according to
the sign of these forces) occur over the fixed support E1;
Track-bridge interaction in railway lines 207
Track T2
20
-40
-60 -51,74
-66,28
-80 -76,64
Fixed support -86,33
k=3300x10³ kN/m -90,83
-100
k=660x10³ kN/m
-120
k=330x10³ kN/m
-126.11
-140
a) 0 100 200 300 400 500 600
x [m]
Track T2
20
Fixed support 15,30
15 k=3300x10³ kN/m 14,28
Additional rail stresses [MPa]
-5
-10
-15
-20
b) 0 100 200 300 400 500 600
x [m]
Track T2
20
10
Additional rail stresses [MPa]
0
-10
-16,27
-20
-30 -29,89
-40
-50 Fixed support
k=3300x10³ kN/m -57,23
-60
k=660x10³ kN/m
-70
k=330x10³ kN/m -77,07
-80
c) 0 100 200 300 400 500 600
x [m]
Figure 8. Normal stress in the rails of track V2 as a function of the stiffness of the abutment/foundation
group for the loads: (a) of an uniform temperature variation; (b) of the LM71 load model and (c) of starting
and braking.
208 Track-Bridge Interaction on High-Speed Railways
Table 1. Support reactions and longitudinal and vertical displacements of the deck for various loads as a
function of the stiffness of the abutment/foundation group.
Displacement [mm]
Stiffness of the E2
abutment/foundation Support
group [kN/m] Loads reaction [kN] δl δv
Track T2
20
0
Additional rail stresses [MPa]
-20
-40
-60 -51,74
-80
-91,77
-100 300,0m
200,0m
-120
100,0m -123,29
-126.11
-140
0 100 200 300 400 500 600 700
x [m]
Figure 9. Normal stress in the rails due to a loading of uniform temperature variation in the track and deck,
for track lengths in the embankment zone of 100, 200 and 300 m.
vi) for this loading scheme, the normal stresses in the rails increase with the decrease of the
stiffness of the abutment/foundation group;
vii) the relative longitudinal displacements in the moving bearing E2 due to traction and braking
loads are strongly influenced by the stiffness of the abutment/foundation group, taken values
of 3.04 mm, for k = ∞, and of 16.80 mm, for k = 330 × 103 kN/m;
viii) the maximum values of the longitudinal support reactions have occurred for the case
corresponding to infinite stiffness of the abutment/foundation group.
In Figure 9 are presented the normal stress results relative to track V2, for an uniform temperature
variation loading, for track lengths in the embankment zone beyond abutment E1 equal to 100, 200
and 300 m.
By looking at the figure it is possible to conclude that, in this case, the minimum length to
consider is of about 200 m, from which results an error of approximately 2.2%, taking as reference
the compression stress obtained from length 300 m.
Track-bridge interaction in railway lines 209
-200 -200
-240 -240
0 100 200 300 400 500 600 700
0 100 200 300 400 500 600 700
x [m] x [m]
160
Figure 10. Maximum and minimum normal stresses in the rails of the V2 track, for the different values of
the stiffness of the abutment/foundation group.
Stiffness of the
abutment/foundation
group [kN/m] δB [mm] δH [mm] δV [mm]
From the inspection of the above table it is possible to conclude that it is only for those cases where
the abutment/foundation group is stiffer (k = ∞ e k = 3300 × 103 kN/m) that the displacement δB
is inferior to the limit established in EN1991-2. The remaining displacements, δH e δV , stay within
the limits for all analysed cases.
4 CONCLUSIONS
In the present paper, the effects resulting from the track-structure interaction have been assessed
for the case of the bridge over the river Moros, a continuous deck bridge with a box type of cross
section designed for the high-speed railway line between Segóvia and Valladolid.
In terms of connections, the deck features a fixed support at one of the ends and moving supports
in the other abutment and columns. The track contains a dilation device, next to the abutment with
moveable bearings.
Analyses were carried out for different values of track length in the embankment zone and of the
stiffness of the abutment/foundation group. The obtained results enable to conclude that it will be
necessary to model a minimum length of 200 m beyond the embankment zone, and that the results
in terms of normal stresses in the rails, of longitudinal support reactions and deck displacements
are highly inflenced by the stiffness of the abutment/foundation group.
In terms of track safety, it has only been possible to control the relative longitudinal displace-
ment between the end of the deck and the abutment, calculated for the starting and braking
loads, for the highest values of the stiffness of the abutment/foundation group, that is, k = ∞
and k = 3300 × 103 kN/m. All other limits have been respected from all the cases considered for
the stiffness of the abutment/foundation group.
ACKNOWLEDGEMENTS
The authors wish to acknowledge RAVE for the support provided and to Prof. José Maria Goicolea of
ETSICCyP in Madrid for the design elements of the bridge over river Moros and for all information
on this issue kindly made available.
REFERENCES
[1] UIC Code 774-3-R, “Track/bridge interaction – Recommendations for calculations”, 2nd edition, Union
Internationale des Chemins de Fer, UIC, 2001.
[2] Parra, F., “Proyecto de una puente de alta velocidad”, E.T.S. Ingenieros de Caminos, Canales y Puertos,
Universidad Politécnica de Madrid, 2005.
[3] Simões, R., “Interacção via-estrutura em pontes ferroviárias em linhas de alta velocidade”, Tese de
Mestrado, FEUP, Porto, Portugal, 2006 (to be submitted).
[4] EN1991-2, Actions on structures – Part 2: General actions – Traffic Loads on Bridges, European
Committee for standardization, CEN, 2003.
[5] EN1991-1-5, Actions on structures – Part 1-5: General actions – Thermal actions, European Committee
for standardization, CEN (2003).
[6] EN1990-A2, Basis of Structural Design – Annex A2: Application for bridges (normative), Final PT Draft,
European Committee for standardization, CEN (2005).
Author index
211
Subject index
Acceleration Creep 98
Car body 169
Filtered 181 Damping 60, 119
Peak ground 31 Ratio 172, 180, 181
Structural 169, 174, 176, 181 Deck
Analysis End rotation 1
Dynamic 11, 118, 142, 168, 169–172, Displacement
174, 180 Longitudinal 38, 44–46, 193, 204
Elastic 41, 68 Relative 4, 5, 15, 29, 33, 34, 95, 97, 98,
Life safety 2 100, 102
Linear 42, 68 Vertical 88, 107, 194
Multimodal 43, 44, 45 Derailment 91, 162, 180
Non-linear 32, 33, 130, 141 Design
Plastic 42, 44 Criteria 14–16, 39–46, 129–141, 169–170
Response Spectrum 33, 41, 61 Life 31
Risk 2 Dynamic
Sequential 122 Analysis 168, 169–172, 174–179, 180–182
Single modal 43 Behaviour 8, 165, 169, 171, 184
Spectral 43, 44 Response 1, 8, 169, 171
Time history 33, 58, 60 Signature 11, 12
Ballast Earthquake
Behaviour 29, 33, 63 Moderate 55, 58, 60
Stability 2, 63 Motion 77, 86, 87, 91, 92
Stiffness 30, 119 Non-collapse 31
Bearing Service 2, 31–33
Elasticity 44, 90 Severe 77, 86
Elastomeric 48, 50 Ultimate 31, 41
Fixed 12–13, 45, 73, 146 Eurocode
Lateral 38, 48, 49, 50 EN 1991-2 12, 14, 139
Neoprene 48, 52 Excitation
Pot 48, 50, 51, 132 Multi support 33
Sliding 43, 48, 104, 110 Single support 33
System 37, 43, 47, 51
Behaviour Fatigue
Elastic 13, 116 Damage 85
Factor 42 Crack 46
Friction 29, 168 Fixed
Long term 65 Point 39, 41
Plastic 127 Foundation 3, 5, 42, 44, 132, 166, 206
Braking 3, 4, 19, 20, 23, 27, 28, 66, 105, Friction
199, 202 Coefficient 22, 132, 135, 152, 153
Bridge
Cable stayed 141–146 High-speed
Suspension 84, 162 Line 7, 8, 124, 129, 156
Load Model 11, 12
Comfort 91, 92, 169, 170, 172 Operation 2
Contact Train 1, 9, 170
Force 69, 86
Model 87 Interaction
Wheel/rail 87 Rail-structure 55–61
213
214 Subject index
Resilience 149, 162 Train 1, 8, 9, 11, 12, 30, 31, 32, 33, 55, 56, 57,
Safety 1, 188, 199. 203–204, 209–210 58, 59, 60, 66, 67, 83, 84–85, 86, 87, 88, 90,
Slab 2, 6, 80, 81, 153, 155, 158, 159, 161, 92, 98, 99, 100, 109, 120, 125, 165, 166,
163, 169, 170, 173, 184 169, 170–171, 174, 176, 178, 182, 184
Stability 1, 63 Transition
Straight 193 Area 156–158
Unloaded 58, 97, 110, 111, 194, 196 Slab 160, 161, 163, 168, 179–182, 183, 184
Traction 19, 20, 22, 23, 25, 29, 30, 98, 99, 100,
102, 103, 104, 105, 106, 130, 144, 191, 193, UIC
196, 197, 198, 208, 209 Code 774-3R 29
Traffic 2, 7, 8, 12, 14, 15, 43, 99, 100, 103, 105,
130, 134, 135, 150, 191, 193 Vehicle 1, 9, 84, 85, 86, 87, 93