Professional Documents
Culture Documents
LN1134
LN1134
ON/OFF
CIN CE NC COUT
GND
GND GND
Caution: 1. The above connection diagram and constant will not guarantee successful operation. Perform thorough
evaluation using the actual application to set the constant.
2. Input capacitor (CIN): 1.0µF or more, Output capacitor (COUT): 1.0µF or more
3. A general series regulator may oscillate, depending on the external components selected. Check that no
oscillation occurs with the application using the above capacitor.
■ Pin Configuration
5 4 4 3 IN CE
4 3
VOUT NC VIN VOUT
■ Pin Assignment
Pin Number
Pin Name Function
SOT23-5L /SOT353 DFN1010-4L SOT343
1 4 4 VIN Supply power
2 2 2 GND Ground
3 3 1 CE Enable pin
4 - - NC NC
5 1 3 VOUT Voltage output
■ Marking Rule
SOT23-5L, SOT353, SOT343
①②③④ ①②③④
SOT23-5L/SOT353 SOT343
(TOP VIEW) (TOP VIEW)
①②
VIN
ON/OFF each
CE
Control
Current
Limiter
VOUT
R2
R1
Voltage
Reference GND
VOUT(S) VOUT(S)
Output Voltage VOUT(E) VIN =VOUT(S)+1.0 V, IOUT=30 mA VOUT(S) V
×0.98 ×1.02
CE “High”Current (no
ICEH VIN=VCE=VOUT(T)+1.0V -0.1 - 0.1 uA
resistor built in)
CE “Low” Current (no
ICEL VIN= VOUT(T)+1.0V, VCE=VSS -0.1 - 0.1 uA
resistor built in)
VIN= VOUT(T)+1V, CL=47uF,
Inrush Current IRUSH VCE=0→VOUT(T)+1V(Only when - - 800 mA
rising and within 1ms)
80 3.6
TJ=25℃, VOUT=3.3V TJ=25℃, IL=30mA
Quiescent Current (uA)
70
3.5
3.4
50
40 3.3
30
3.2
20
3.1
10
0 3.0
0 1 2 3 4 5 6 7 3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0 6.3 6.6 6.9
3. Output Current Limit VS Input Voltage 4. GND Pin Current VS Input Voltage
800 200
TJ=25℃ TJ=25℃, IL=1mA
Output Current Limit (mA)
180
700 GND Pin Current (uA) TJ=25℃, IL=50mA
160 TJ=25℃, IL=100mA
600
140
500 120
400 100
80
300
60
200
40
100 20
0 0
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
200 160
TJ=25℃, VIN=CE=4.3V VIN=CE=4.3V
Quiescent Current (uA)
180 140
GND Pin Current (uA)
160
120
140
100
120
80
100
60
80
40
60
40 20
20 0
0 100 200 300 400 500 -40 -20 0 20 40 60 80 100 120
1000 3.9
Output Current Limit (mA)
700 3.6
600 3.5
500 3.4
400 3.3
300 3.2
200 3.1
100 3.0
0 2.9
-40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120
200 1.30
IL=10mA VIN=4.3V
180 IL=50mA 1.25
Dropout Voltage (mV)
140 1.15
120 1.10
100 1.05
80 1.00
60 0.95
40 0.90
20 0.85
0 0.80
-40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120
1.2 60
VIN=4.3V VIN=4.3V, IL=1-30mA
1.1 VIN=4.3V, IL=1-100mA
50
CE "Low" Voltage (V)
1.0
40
0.9
30
0.8
0.7 20
0.6
10
0.5
0
0.4
-10
0.3
0.2 -20
-40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120
15. Load transient response (IL=10-350-10mA) 16. Ripple-Rejection (IL=50mA, Vpp=1V, F=1KHZ)
ON/OFF
CIN CE NC COUT
GND
GND GND
Input capacitors(CIN)and output capacitors(COUT) are recommended to use more than 1uF, which can ensure the
stability of the system
PCB Layout
In order to get better use effect, the main points for attention of PCB layout are as follows:
The input and output capacitors are as close as possible to the chip pins.
The wiring of VIN and VOUT should be as thick as possible to reduce the wiring resistance and improve the load
performance.
The route from GND(pin) to GND uses a dedicated channel to prevent parasitic resistance from introducing into the
change path, which results in incorrect feedback ratio and output error.
D θ
b 0.2
L
E1
E
e
c
e1
A1
A2
D
E2
D2 b
K 3 4
E C0.12
2 1 L
e
TOP VIEW BOTTOM VIEW
SIDE VIEW
Dimensions In Millimeters Dimensions In Inches
Symbol
Min Max Min Max
K 0.15 - 0.006 -
θ
D
e1
e
E
E1
L1
0.20
b c
A1
A2
D
e1
e
E
E1
L1
0.20
b c
A1
A2