Professional Documents
Culture Documents
Page 1 of 13
Contents Page
General Information 4
Contraindications 4
Safety Instructions 5
Electrical Safety 6
Installation 7
Warranty 13
Page 2 of 13
Introduction and Intended Use
Congratulations on the purchase of your new BIXEPS device. These high-quality products are
manufactured with the greatest care and meet our high-quality standards, as well as the
international safety and production standards. Designed to be simple and easy to use, we
hope you will enjoy the benefits of BIXEPS.
Please ensure that you have completely read and understood this instruction manual before
installing or using BIXEPS. It contains important information for proper usage and operation
of the device. Non-observance with these instructions may lead to user injury or damage to
the unit.
Display Screen
Field Chamber
(with adjustable
height)
Footrest (for
users to step up)
Roller wheels
with lock
BIXEPS is a safe and easy to operate wellness device. It uses proprietary low-energy, low
frequency magnetic fields to activate muscle safely and non-invasively without contraction,
without stress or strain. It is intended to improve the strength and function of users, promoting
overall fitness and well-being. Over time the positive benefits of muscle activation build, and
users may experience improvements in their strength, endurance and overall function.
Page 3 of 13
General Information
BIXEPS sessions have been designed to take only ten (10) minutes. During which our unique
magnetic fields have been shown to activate the mitochondria (or the “powerhouse”) found
within muscle. This similar process of muscle-mitochondria activation occurs in muscles
during exercise and results in muscle adapting and improving its endurance and performance.
Activated muscles have also been shown to release myokines signals to moderate other
physiological functions in the rest of the body (e.g. inflammation, metabolism and recovery).
Most users have seen results with just one BIXEPS session each week. We recommend that
BIXEPS is not used more than twice each week, with consecutive sessions spaced 48
hours apart. BIXEPS is preferably applied to the lower limbs of users where possible, so as
to activate the larger volumes of muscles. We recommend alternating the limbs where BIXEPS
is applied each (e.g. first session should be applied to the left thigh with the next session
applied to the right) so as to spread the effects of BIXEPS throughout the body.
Disclaimer: BIXEPS is not a medical device and is not intended to treat, diagnose, cure
or prevent any disease or illness. The information in this manual does not intend to
recommend our device as a treatment or as a diagnosis for any illness or disease
condition.
Page 4 of 13
Exclusions
While BIXEPS uses low strength magnetic signals, there are still adherent risks for persons
sensitive to magnetic fields. You should not use BIXEPS if you fit the following criteria:
Safety Instructions
BIXEPS devices are designed to be safe for use and easy to operate. Nevertheless, hazards
may result from the inappropriate use of this product which does not comply with the
manufacturer’s instructions. Should you have any questions about how to operate the device,
please do not hesitate to contact us at enquiry@quantumtx.com.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Ensure that the power cable and power plug is in an undamaged condition.
• Ensure that the area around BIXEPS device is clear from obstacles.
• Ensure that BIXEPS devices is used on a stable, non-sloping surface (i.e. floor).
• BIXEPS is meant to be used when seated. Please ensure that you have a comfortable
sitting position (e.g. chair) when using the device, and use a non-wheeled chair with
proper backrest
• Ensure that BIXEPS is in a clean and dry state before use.
• Check for any damages to the device and contact the manufacturer regarding any
defects or damaged parts.
• DO NOT place any beverages or liquids on the device.
• DO NOT wash the device with splashing or running liquids, soap and / or water.
• BIXEPS devices are not toys. Keep products out of reach of children and pets.
• DO NOT misuse BIXEPS devices. The products may not be used for any purposes
other than those mentioned here.
• DO NOT tamper with or modify the BIXEPS device without authorization from the
manufacturer.
Page 5 of 13
Electrical Safety
BIXEPS signals are low-frequency and operate within the non-ionizing realm of radio waves
(0-10kHz). The signals have low magnetic flux densities (1-2 MilliTesla) which is about 20-40
times the earths’ natural magnetic field (25-70 MicroTesla) and a thousand times lower than
a hospital Magnetic Resonance Imaging machines (1-3 Tesla). Our highest magnetic field
densities fall safely within human exposure restrictions defined by IEC 62311: Assessment of
electronic and electrical equipment related to human exposure restrictions for electromagnetic
fields (0 Hz to 300 GHz), which defines limits on exposure of people related to electric,
magnetic and electromagnetic fields.
• IEC 60335: 2010, Household and similar electrical appliances - Safety - Part 1: General
requirements
Page 6 of 13
Installation
• After unboxing, place device on a flat, even surface before operating it.
• Find a suitable, stable chair (preferably with a backrest) that can be used during
BIXEPS 10-minute sessions.
• Open the service port as seen in the schematic diagram below to adjust the height of
the field chamber.
• Aligning the bottom of the field chamber to the height of the chair by adjusting the
Height Adjustment Knob (as seen in the schematic below). Note: This should be a one-
time adjustment, but you may choose to make minor fine-tuned adjustments, if needed.
• Unwind the cable that can be found in the service port. Plug the power cord into the
Power Cord Receptacle and connect the other end to the wall socket with appropriate
voltage.
• Switch on the Main Switch of the device found in the service port. You should see the
BIXEPS splash screen as seen below on your screen once the device is powered up:
• If you have any difficulties with the set-up, please contact QuantumTX at
support@quantumtx.com.
Page 7 of 13
Using BIXEPS Personal Use Devices
Step 2. Press the “Start” button to exit standby mode. You should see the “Ready”
screen (Figure A).
Step 3. Follow the instructions on screen (Figure A) by ensuring you are seated
comfortably on a chair, before pulling the device towards you while placing your
leg into the machine.
Step 4. Press the “Start” button when ready to begin your session.
Step 5. Remove your leg from the device after the screen indicates that the 10 minutes
is up (Figure B).
Step 6. Wipe down the machine after use; turn off the power supply if the machine will
not be used for a long time (e.g. overnight).
Page 8 of 13
Using BIXEPS Community Use Devices
Step 2. Tap the card on the RFID Card Reader to enter the Ready Mode. You should
see the “Ready” screen (Figure A).
Alternatively, you might see a “Recently Used Screen” may appear (see Figure
C). This screen indicates that the user has used BIXEPS within the last 48
hours. The programme will not proceed to allow the fields to turn on at this point.
If you want to override this system, use the operator’s card to override the
system and allow for the fields to turn on.
Step 3. Follow the instructions on screen (Figure A) by ensuring you are seated
comfortably on a chair, before pulling the device towards you while placing your
leg into the machine.
Step 4. Press the “Start” button when ready to begin the session.
Step 5. Remove your leg from the device after the screen indicates that your 10-minute
session is finished (Figure B).
Page 9 of 13
Figure B - BIXEPS session ended screen
Step 6. Wipe down the machine after use; leave the machine idle for the next user, or
turn off the power supply if the machine will not be used for a long time (e.g.
overnight).
Note:
1. In both operating mode and when the fields are active, the “Stop” button can be used
(hold for 1 sec) to interrupt/terminate the session if the user wishes to do so.
Page 10 of 13
Cleaning and Storage
Device Disposal
BIXEPS devices should be serviced regularly by a trained professional. They will perform
routine calibration, servicing, maintenance, and software updates to ensure that your device
is working at its optimum.
During the usage of device, if the device display prompts that a fault is detected (e.g. current
over-flow, power malfunction), stop using the device immediately and turn off device power.
Contact QuantumTX team for technical assistance.
• Is the power supply connected to the outlet correctly? If not, connect the power supply
to the outlet.
• Is the power supply connected to the BIXEPS device correctly? If not, connect the
power supply to the BIXEPS device.
• Are all relevant cables and plugs undamaged?
• DO NOT attempt to disassemble the device. Any tampering with the device will void
all existing warranties.
For all other device malfunctions or troubleshooting please contact the manufacturer or the
corresponding agent. When in doubt, you can obtain additional information at
http://www.quantumtx.com.
Page 11 of 13
Functional Specifications
Technical Specifications
Page 12 of 13
Warranty
The manufacturer warranty covers equipment fault under normal operating use and
maintenance conditions.
This warranty does not extend to cover regular recalibration and / or maintenance of any kind.
The warranty applies only to the first acquiring purchaser and does not extend to products or
components thereof, which were not properly used, or to products where changes have been
made. Any warranty is rendered null and void by non-intended use of the BIXEPS devices.
The warranty obligation is limited to repairs of the device or its components, sent to the
manufacturer during the warranty period. A pre-requisite is that the manufacturer
acknowledges that the product is defective, and the defect is not attributable to improper
handling or changes to the product, or due to any abnormal operating conditions.
Any warranty obligation will expire if repairs on BIXEPS devices are carried out by persons
not authorized by the manufacturer.
The terms of this warranty apply exclusively and in place of all other contractual or statutory
obligations, including, but not limited to, the legal warranty regulations of the marketability, the
suitability and the expediency for the specific application.
The manufacturer assumes no responsibility for direct and indirect, incidental or consequential
damage, regardless of whether it is the result of lawful, unlawful or any other action.
Warranty and liability claim in relation to damage to persons or property are excluded if they
can be traced to one or more of the following causes:
• Unintentional or negligent use of BIXEPS devices.
• Improper use, operation and maintenance of BIXEPS devices.
• Noncompliance with the guidelines/warnings found in the operating instructions.
• Unauthorized, structural changes to BIXEPS devices.
• Noncompliance with the operating instructions.
• Parts that are to be regularly checked, exchanged or are subject to wear, for example
the battery.
• Improperly handled repairs and the use of parts, replacement parts or accessories not
recommended by the manufacturer.
• Disaster and force majeure.
Please register the device with your dealer. You can find detailed and country-specific
information about this on our www.quantumtx.com
Page 13 of 13