Professional Documents
Culture Documents
JDM Al
Specification for Hot-Rolled Steel
Bars, Plates & Shapes
1. SCOPE
JDM Al specifies general requirements of hot-rolled carbon, high-strength low-alloy and alloy steel bars, plates
and shapes of the descriptions and sizes shown in Table 1.
JDM Al does not apply to the following products which are covered by other JDM specifications
2. DESIGNATION
The mechanical and/or chemical requirements may be specified in one of three ways
To chemical composition conforming to requirements of JDM AO and designated by JDM composition number.
Example: JDM 1020.
To composition and mechanical properties conforming to JDM Al 3 and designated JDM Al 3 with appropriate
suffix. Example: JDM Al 3C.
To composition and mechanical properties conforming to ASTM A36/A36M and designated JDM A20.
3. REQUIREMENTS
Unless otherwise specified, the standard provisions of the latest relevant ASTM specification shall apply for all
points not taken up in this JDM specification. Supplementary or special requirements, if any, shall be specified
by the purchaser.
3.1 COMPOSITION AND PROPERTIES. Chemical composition, mechanical or other properties, and quality level
shall conform to the requirements specified by JDM AO, JDM Al 3, or JDM A20 as applicable, for the designated
JDM number.
3.2 DIMENSIONAL TOLERANCES AND OTHER GENERAL REQUIREMENTS. Unless otherwise specified by
the purchaser, hot-rolled steel products covered by this specification shall be furnished conforming to the
permissible variations for dimensions and other general requirements published in the latest issue of the applicable
reference specifications shown in Table 1. Dimensional tolerances for special shapes or sizes or sizes not shown
in Table 1 shall be specified by the purchaser.
w
TABLE 1. GENERAL REQUIREM NTS SPECIFICATIONS -
(Including Dimensional Tolerances)
PRODUCT DESCRIPTION SIZE RANGE REFERENCE SPECIFICATION
mm in JDM AO GRADES JDM A13
THICKNESS THICKNESS &
WIDTH OR WIDTH OR CARBON ALLOY JDM A20 .
HOT-ROLLED STEEL: DIAMETER DIAMETER GRADES
~ 5.5 > .219 ASTM
Iound
~ound
3ar for Springs
Square
4exagon
3ctagon
3ar Size 8hapes
Vtgle, Channel, Tee < 75(c) I 1< 3.00(C) I I A29/A29M(d)
I
> 75(c) > 3.00(C) ASTM
Structural Shapes
A6/A6M(d) ASTM
A6/A6M(d)
>6 >5 2 .25 2 .2031
‘la!(a)
(a) Flats shall be rolled on four sidea square edge flats unless otherwise apacified by the purchaser.
(b) Does not include Commercial Quality Hea~ Thickness Sheet & Strip Coils (formerly “Plate Coils”). See JDM A4.
(c) Largest dimension Of the cross section.
(d) The ASTM “M” designation shall apply for products ordered by dimensions in mm.
(e) Dimensional tolerances of plates ordered by dimensions in millimeters shall be as spacifiad either by ISO 7452 for Class B or by ASTM A6M
2
[AppROVEO Fm 1
JDM Al
4. ORDERING INFORMATION SUPPLIER DIST, 1
Orders for material under this specification shall include the following information as needed to describe the
requirements:
● Quantity
● Size, shape, and length
. JDM designation (steel grade)
● Quality level (see JDM AO)
5. REFERENCES
ASTM A6/A6M Specification for General Requirements for Rolled Steel Plates, Shapes, Sheet Piling, and Bars
or Structural Use
ASTM A29/A29M Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought and Cold
Finished
ASTM A679 Specification for Carbon and Alloy Steel Bars for Springs
ISO 7452 Hot-Rolled Structural Steel Plates - Tolerances on Dimensions and Shape
SAE J510 Leaf Springs for Motor Vehicle Suspension - Made to Customary U.S. Units
SAE J1123 Leaf Springs for Motor Vehicle Suspension - Made to Metric Units
I
1