Professional Documents
Culture Documents
081 Principles of Flight (JAA ATPL Theory) - (PDFDrive)
081 Principles of Flight (JAA ATPL Theory) - (PDFDrive)
This is the second edition of this manual, and incorporates all amendments to previous editions, in
whatever form they were issued, prior to July 1999.
The information contained in this publication is for instructional use only. Every effort has been made to ensure
the validity and accuracy of the material contained herein, however no responsibility is accepted for errors or
discrepancies. The texts are subject to frequent changes which are beyond our control.
Help
TO NAVIGATE THROUGH THIS MANUAL
When navigating through the manual the default style of cursor will be the hand symbol.
This version of the CD-Online manual also supports a mouse incorporating a wheel/
navigation feature. When the hand tool is moved over a link on the screen it changes to a
hand with a pointing finger. Clicking on this link will perform a pre-defined action such as
jumping to a different position within the file or to a different document.
Navigation through a manual can be done in the following ways:
Help
The INDEX The EMAIL button The PAGE The SEARCH button allows
button takes you to enables you to send button takes you you to search for specific
the Index of the us your comments to the previous words within the manual
manual you are in, regarding this and next pages (More information can be
if it is available. product, provided in the book. found in the ‘Searching’
you have an internet section). The arrows are used
connection. to display the previous and
next words whilst using the
search tool.
The CONTENTS The WEB The BACK button The HELP The EXIT
button takes you to button takes returns you to your button button exits
the first page of the you to the previous position in takes you from the
main Table Of Click2PPSC the document. to the help application.
Contents. web site. pages.
Aerodynamic Principles
Units
Systems of Units
Newton's Laws of Motion
The Equation of Impulse
Basic Gas Laws
Airspeed Measurement
Shape of an Aerofoil
The Equation of Continuity
Bernoulli’s Theorem
1 Aerodynamic Principles
Units
1. In order to define the magnitude of a particular body in terms of mass, length, time,
acceleration etc., it is necessary to measure it against a system of arbitrary units. For example, one
pound (lb) is a unit of mass, so the mass of a particular body may be described as being a multiple
(say 10 lb), or sub-multiple (say ½ lb) of this unit. Alternatively the mass of the body could have
been measured in kilograms, since the kilogram (kg) is another arbitrary unit of mass.
Systems of Units
2. There are a number of systems of units in existence and it is essential when making
calculations to maintain consistency by using only one system. Three well-known consistent systems
of units are the British, the c.g.s. and the S.I. (Systeme Internationale). These are illustrated in
Figure 1-1 below:
FIGURE 1-1
Units of BRITISH C.G.S. S. I.
Measurement
SYSTEM
LENGTH Foot Centimetre Metre (m)
3. The S.I. system of units is the one most commonly used. In this system, one Newton is the
force that produces an acceleration of 1 M/s² when acting upon a mass of 1 kg.
5. Force is that which changes a body's state of rest or of uniform motion in a straight line. The
most familiar forces are those which push or pull. These may or may not produce a change of
motion, depending upon what other forces are present. Pressure acting upon the surface area of a
piston exerts a force that causes the piston to move along its cylinder. If we push against the wall of
a building a force is exerted but the wall does not move, this is because an equal and opposite force is
exerted by the wall. Similarly, if a weight of 1 kilogram is resting upon a table there is a force
(gravitational pull) acting upon the weight but, because an equal and opposite force is exerted by the
table, there is no resultant motion.
F= ma
Where: F = Force m = mass and a = acceleration
7. Inertia is the tendency of a body to remain at rest or, if moving, to continue its motion in a
straight line. Newton's first law of motion, often referred to as the law of inertia, states that every
body remains in a state of rest or uniform motion in a straight line unless it is compelled to change
that state by an applied force.
Momentum
8. The product of mass and velocity is called momentum. Momentum is a vector quantity, in
other words it involves motion, with direction being that of the velocity. The unit of momentum has
no name, it is given in kilogram metres per second (kg m/s). Newton's second law of motion states
that the rate of change of momentum of a body is proportional to the applied force and takes place in
the direction in which the force acts.
9. Newton's third law of motion states that to every action there is an equal and opposite
reaction. This describes the situation when a weight is resting upon a table. For a freely falling body
the force of gravity (gravitational pull), measured in Newtons , acting upon it is governed by:
F = mg
where g is acceleration due to gravity 9.81M/s², and m is the
mass of the body in kilograms.
10. If the same body is at rest upon a table it follows that, since there is no motion, there must be
an equal and opposite force exerted by the table.
v = u + a.t
12. If it is required to calculate the distance travelled (s) during a period of motion with constant
acceleration, this can be done using the equation:
1
s = --- ( u + v )t
2
13. By substitution, using the above two equations, it is possible to develop two more equations:
1
s = ut + --- at 2
2
And:
v 2 = u 2 + 2as
F = ma
And therefore
F
a = ----
m
15. If the force acts in the direction of motion of the body for a period of time (t), the resultant
acceleration will cause a velocity increase from (u) to (v). This must also cause an increase in
momentum from (mu) to (mv). Combining the equations F = ma and v = u+at gives:
v = u + t ----
F
m
Ft = mv – mu
16. The change in momentum (final momentum minus initial momentum) due to a force acting
on a body is the product of that force and the time for which it acts. This change in momentum
called the impulse of the force and is usually identified by the symbol J. Hence:
J = Ft
Or:
J = mv – mu
17. This is the equation of impulse. The S.I. unit of impulse, being the product of force and time,
is the Newton second (Ns). NOT, it should be noted, Newton per second (N/s).
(a) The relation between volume (V) and pressure (P) at constant temperature (Boyle's
Law).
(b) The relation between volume (V) and temperature (T) at constant pressure (Charles'
Law).
(c) The relation between pressure (P) and temperature (T) at constant volume (Pressure
Law)
Boyle's Law
19. Boyle's Law states that the volume of a fixed mass of gas is inversely proportional to the
pressure, provided that the temperature remains constant. In other words, if the volume of a given
mass of gas is halved its pressure will be doubled or, if its pressure is halved its volume will be
doubled, providing its temperature does not change.
P1 V1 = P2 V2 or PV = cons tan t
Charles' Law
21. Charles Law states that the volume of a fixed mass of gas at constant pressure expands by 1/
273 of its volume at 0°C for every 1°C rise in temperature. In other words, the volume of a given
mass of gas is directly proportional to its (absolute) temperature, providing its pressure does not
change.
V1 V2 V
------ = ------ or ---- = cons tan t
T1 T2 T
Pressure Law
23. The pressure law is the result of experimentation during the nineteenth century by a professor
called Jolly and states that the pressure of a fixed mass of gas at constant volume increases by 1/273
of its pressure at 0°C for every 1°C rise in temperature. In other words, the pressure of a given mass
of gas is directly proportional to its temperature, providing its volume does not change.
P1 V1 P2 V2 PV
------------- = ------------- or -------- = cons tan t
T1 T2 T
Static Pressure
26. The static pressure of the atmosphere at any given altitude is the pressure resulting from the
mass of an imaginary column of air above that altitude. In the International Standard Atmosphere
(ISA) at mean sea level the static pressure of the atmospheric air is 1013.25 millibars (mb), which
equates to 14.7 pounds per square inch (psi) or 29.92 inches of mercury (in. Hg). ISA mean sea level
conditions also assume an air density of 1.225 kilograms per cubic metre (kg/m³) and a temperature
of +15°C (288°A). The standard notation for static pressure at any altitude is (P).
Dynamic Pressure
27. Air has density (mass per unit volume) and consequently air in motion has energy and must
exert pressure upon a body in its path. Similarly, a body moving in air will have a pressure exerted
upon it that is proportional to its rate of movement, or velocity (V). This pressure due to motion is
known as dynamic pressure and is given the notation (q).
28. Energy due to motion is kinetic energy (K.E.) and in the S.I. system of units is measured in
joules (j). From Bernoulli’s equation for incompressible flow the kinetic energy due to air movement
may be calculated using the formula:
1
KE = --- ρV 2
2
29. To calculate kinetic energy in joules, density (ρ) must be in kilograms per cubic metre (kg/m³)
and velocity (V) in metres per second (m/s). One joule is the work done when a force of 1 newton
moves the point of application of the force 1 metre in the direction of the force.
30. If a volume of moving air is brought to rest, as in an open-ended tube facing into the
airstream, the kinetic energy is converted into pressure energy with negligible losses. Hence, dynamic
pressure:
1
q = --- ρV 2
2
31. It should be noted that dynamic pressure cannot be measured in isolation, since ambient
atmospheric pressure (static pressure) is always present also. The sum of the two, (q+P), is known
variously as total pressure, stagnation pressure or pitot pressure and is given the notation (H or Ps).
Therefore, dynamic pressure:
q = (q + P ) – P
Viscosity
32. Viscosity is a measure of the internal friction of a liquid or gas and determines its fluidity, or
ability to flow. The more viscous a fluid, the less readily it will flow. Unlike liquids, which become
less viscous with increasing temperature, air becomes more viscous as its temperature is increased.
The viscosity of air is of significance when considering scale effects in wind tunnel experiments and
in terms of friction effects as it flows over a surface. Changes of density do not affect the air
viscosity.
Density
33. Density (ρ) is defined as mass per unit volume. The density of air varies inversely with
temperature and directly with pressure. When air is compressed, a greater mass can occupy a given
volume or the same mass can be contained in a smaller volume. Its mass per unit volume has
increased so, by definition, its density has increased.
34. When the temperature of a given mass of air is increased it will expand, thus occupying a
greater volume. Assuming that the pressure remains constant the density will decrease because the
mass per unit volume has decreased.
35. Both the above statements assume that the air is perfectly dry. When air is humid, that is it
contains a proportion of water vapour, it becomes less dense. This is because water vapour weighs
less than air and so a given volume of air weighs less if it contains water vapour than if it were dry.
Its mass per unit volume is less.
Airspeed Measurement
Indicated Airspeed (IAS)
36. The speed displayed on the airspeed indicator (ASI) is known as indicated airspeed. It does
not include corrections for instrument errors and static pressure measurement errors (pressure error),
both of which are very small. The indicated airspeed will differ progressively from actual flight speed
as altitude increases and, consequently, density (ρ) decreases (q = ½ρV²). The notation for IAS is
(VI).
EAS
TAS = ------------
σ
where
ρ
σ = relative air density = -----
ρ0
40. TAS is given the notation (V). At 40,000 ft, where standard density is one-quarter sea level
density, TAS will be twice EAS (√0.25 = 0.5). British ASI’s, in common with most others, are
calibrated for ISA mean sea level density (ρ0), where EAS = TAS. At all greater altitudes TAS will be
greater than EAS by a proportional amount.
Shape of an Aerofoil
41. The terminology for the dimensions that determine the shape of an aerofoil section is shown
in Figure 1-2 below.
FIGURE 1-2
Aerofoil Section
Chord Line
42. A straight line joining the leading edge to the trailing edge of the aerofoil.
Chord (c)
43. The distance between leading and trailing edge measured along the chord line.
Thickness/Chord Ratio
44. The maximum thickness of the aerofoil section, expressed as a percentage of chord length. A
typical figure is about 12 per cent. The distance of the point of maximum thickness from the leading
edge, on the chord line, may also be given as a percentage of chord length. Typically it is about 30
percent.
Camber
46. The displacement of the mean camber line from the chord line. The point of maximum
camber is expressed as a percentage and is the ratio of the maximum distance between mean camber
line and chord line to chord length. The amount of camber and its distribution along the chord
depends largely upon the operating requirements of the aircraft. Generally speaking, the higher the
operating speed of the aircraft the less the camber (i.e. the thinner the wing).
Nose Radius
47. The nose or leading edge radius is the radius of a circle joining the upper and lower surface
curvatures and centred on a line tangential to the curve of the leading edge.
Angle of Incidence
49. The angle between the aircraft wing chord line and the longitudinal centreline of the aircraft
fuselage.
Wing Span
51. The straight-line distance measured from tip to tip. See Figure 1-3.
FIGURE 1-3
Wing Span
Wing Area
52. The plan surface area of the wing. In a wing of rectangular planform it is the product of span
x chord.
Aspect Ratio
2
53. The ratio of wing span to mean chord or span to wing area.
Wind Loading
54. The weight per unit wing area.
Root Chord
55. The chord length at the centreline of the wing (the mid-point along the span).
Tip Chord
56. The chord length at the wing tip.
Tapered Wing
57. A wing in which the root chord is greater than the tip chord.
Taper Ratio
58. The ratio of tip chord to root chord usually expressed as a percentage.
Swept Wing
60. A wing in which the quarter chord line is not parallel with the lateral axis of the aircraft. See
Figure 1-4.
Sweep Angle
61. The angle between the quarter chord line and the lateral axis of the aircraft. See Figure 1-4.
FIGURE 1-4
Sweep Angle
FIGURE 1-5
Mean
Aerodynamic
Chord
Dihedral
63. The upward inclination of the wing to the plane through the lateral axis. See Figure 1-6.
FIGURE 1-6
Dihedral
Anhedral
64. The downward inclination of the wing to the plane through the lateral axis. See Figure 1-7.
FIGURE 1-7
Anhedral
66. Figure 1-8 illustrates the streamline flow of air through a cylinder of uniform diameter. The
air mass flow is the product of the density of the air (ρ), the cross-sectional area of the cylinder (A)
and the flow velocity (V). At any point along the cylinder:
FIGURE 1-8
Streamline Flow
67. Mass flow = ρAV = constant is the general equation of continuity, which applies to both
compressible and incompressible fluids. In compressible flow theory it is convenient to assume that
changes in density can be ignored at speeds below about 0.4 Mach and a simplified equation of
continuity:
AV = cons tan t
68. Consider now the streamline airflow through a venturi tube as illustrated at Figure 1-9.
Given that mass flow is constant at any point and is the product of AV then at point Y, since the
cross-sectional area (A) is reduced, velocity (V) must increase in order to maintain the equation of
continuity.
FIGURE 1-9
69. In other words, a reduction in cross-sectional area (as in a venturi tube) produces an increase
in velocity and vice-versa.
Bernoulli’s Theorem
70. A gas in motion possesses four types of energy. Potential energy (due to height), heat energy,
pressure energy and kinetic energy (due to motion). Bernoulli demonstrated that in an ideal gas in
steady streamline flow the sum of the energies remains constant. At low subsonic (less than 0.4
mach) flow air can be conveniently regarded as an ideal gas (incompressible and inviscid). In these
circumstances Bernoulli's Theorem can be further simplified by assuming there is no transfer of heat
or work in or out of the gas and by ignoring the insignificant changes in potential energy and heat
energy.
71. For practical purposes then, in streamline flow of air around an aircraft wing at low subsonic
speed:
1
P + --- ρV 2 = cons tan t
2
73. Where P = static pressure. In other words, static pressure + dynamic pressur = constant.
74. From this simplified Bernoulli's Theorem it is evident that an increase in velocity of gas flow
results in a decrease in static pressure, and vice versa. Hence at point Y in Figure 1-9 the increase in
velocity of airflow will produce a decrease in pressure.
Lift
2 Lift
Airflow Round an Aerofoil
1. As stated in the previous chapter the relationship between pressure and velocity in the airflow
patterns around an object is that defined by Bernoulli. The airflow impacting on the object at a point
near its leading edge will be brought to rest, or stagnate. At the stagnation point the velocity is zero
and the pressure equal to the total pressure of the air stream, that is to say ambient atmospheric
pressure plus dynamic pressure. As the airflow divides and passes around the object the increases of
local velocity, characterised by closely spaced streamlines, produce decreases of local static pressure.
Pressures in excess of ambient atmospheric pressure are conventionally referred to as positive (+) and
pressures below ambient atmospheric pressure as negative (-). The type of airflow around the body
will be either Steady Streamline Flow or Unsteady Flow.
(a) Classical Linear Flow. In this flow pattern the streamlines basically follow the
contours of the body, with no separation of the airflow from the surface. Figure 2-1
illustrates classical linear flow around an aerofoil.
FIGURE 2-1
(b) Controlled Separated Flow or Leading Edge Vortex Flow. It is possible to design an
aerofoil such that the airflow close to the surface separates at the leading edge and
forms a controlled vortex. The main streamline flow is then around this vortex. This
has advantages with swept-wing and delta wing planforms, as will be shown in later
chapters. This is shown at Figure 2-2.
FIGURE 2-2
Leading Edge
Vortex Flow
Unsteady Flow
3. Unsteady Flow occurs when the airflow separates from the surface of the body and the flow
parameters (eg. speed, direction, pressure), at any point, vary with time. The flow thus cannot be
represented by streamlines.
Two-dimensional Flow
4. An aerofoil section has only two dimensions, from leading edge to trailing edge and from
upper surface to lower surface, known as chord and its thickness. Hence, when considering airflow
around it, the consideration is limited to flow in two dimensions only.
FIGURE 2-3
Airflow Around an
Aerofoil
6. The angle at which the aerofoil is inclined to the airflow is called the angle of attack (α). The
greater the angle of attack, the greater the pressure difference and therefore the greater the upward
force produced. This is true up to the point at which the airflow separates from the upper surface,
known as the point of stall. As the airflow approaches the leading edge of the aerofoil it is turned
towards the lower pressure on the upper surface. This effect is known as upwash. As it leaves the
trailing edge it returns to its original, free stream location and this is termed downwash. The upward
force produced as air flows over the aerofoil is the source of lift.
7. Figure 2-4 illustrates the aerodynamic forces acting upon an aerofoil inclined at an angle of
attack (α) to the relative airflow.
FIGURE 2-4
Aerodynamic
Forces Acting on
an Aerofoil
8. The resultant of all the aerodynamic forces acting on the wing is also referred to as the Total
Reaction. The lift force is the component of the resultant force acting perpendicular to the relative
air flow. The component of the resultant force acting parallel to the relative airflow is known as
drag.
FIGURE 2-5
Symmetrical
Aerofoil at Zero
Lift Angle of
Attack
(a) Streamline
Flow
(b) Pressure
Distribution
10. Notice from Figure 2-5(b) how the pressure distribution around the aerofoil can be
conveniently represented in vector form. The pressure at any point on the upper and lower surfaces
of the aerofoil is represented by a vector at right angles to the surface and whose length is
proportional to the difference between absolute pressure at that point and free stream static pressure.
Conventionally, pressures higher than ambient, ie. positive, are represented by a vector plotted
towards the surface and for negative values, the vector is plotted away from the surface.
11. At the leading edge of the aerofoil, where the streamlines diverge, positive pressure exists.
Where the airflow is forced to divide and flow around the aerofoil the streamlines are close together
and high local velocities and negative static pressure exists. The negative pressures are the same
above and below the aerofoil, so with no pressure difference between upper and lower surfaces no
lift is generated. The angle of attack at which this occurs is referred to as the zero lift angle of attack,
for that particular aerofoil. It should be noted that a stagnation point also occurs at the trailing edge,
where the flow velocity decreases to free stream velocity.
12. Consider now the symmetrical aerofoil at a positive angle of attack as shown in Figure 2-6.
The greatest local velocities occur where the streamlines are forced into the greatest curvature as
shown at Figure 2-6a. Consequently the highest velocities occur over the forward part of the upper
surface. Upwash is generated ahead of the aerofoil, moving the forward stagnation point under the
leading edge and creating an area of decreased local velocity below the forward part of the lower
surface. Behind the aerofoil downwash is generated.
FIGURE 2-6
Symmetrical
Aerofoil at Positive
Angle of Attack (a)
Streamline Flow
(b) Pressure
Distribution
13. Figure 2-6(b) illustrates the pressure distribution from which it can be seen that there is a
marked pressure differential between upper and lower surfaces, creating positive lift.
14. A practical aircraft wing would not normally be of symmetrical aerofoil section, but would
have some positive camber since such a section is capable of producing lift even at very low angles of
attack.
15. Figure 2-7 illustrates the pressure distribution around a conventional cambered aerofoil
inclined at a small positive angle of attack.
FIGURE 2-7
Pressure
Distribution
Around a
Cambered
Aerofoil at a Small
Positive Angle of
Attack
16. At point A at Figure 2-7, total pressure (pitot pressure, stagnation pressure) prevails and this
is the forward stagnation point. As the air passes over the upper surface towards point B, it is
moving into an area of reducing pressure and point B is where minimum pressure exists on the upper
surface Beyond B, pressure is increasing until total pressure is recovered at the rear stagnation point
C and thus the air travelling from B to C is moving against an adverse pressure gradient. This is
most significant as the only way the air can travel against this adverse pressure gradient is by virtue
of its kinetic energy and should this be insufficient the air flow will break away or separate from the
wing. This concept is fully covered in Chapter 4 under Stalling.
17. Furthermore, if points A and C are stagnation points and there is negative pressure on both
upper and lower surfaces, then points X on the upper surface and Y on the lower surfaces are points
of static pressure. To reduce the effect of the pressure reduction on the lower surface the curvature of
the lower wing surface is kept to a minimum.
19. As the angle of attack is progressively increased, the negative pressure above the upper surface
steadily increases, whilst that below the lower surface decreases. Beyond about +8°the pressure
below the lower surface becomes positive. Thus, it can be seen that with increasing angle of attack,
the pressure differential between upper and lower aerofoil surface increases. However, at the lower
angles of attack, it is the pressure reduction on the upper surface which is largely responsible for the
lift generated whereas at the higher incidence, it is both the reduced pressure on the upper surface
and the increased pressure on the lower surface which contribute to lift generation.
FIGURE 2-8
Pressure
Distribution
Around an
Aerofoil
FIGURE 2-9
Flat Plate Effect
Centre of Pressure
21. The pressure differential between the upper and lower surfaces can be conveniently
represented by a single aerodynamic force acting at a particular point on the chord line. This point is
known as the centre of pressure (CP). Both the resultant aerodynamic force and hence lift, and the
point through which it acts (CP) vary with angle of attack.
22. From Figure 2-8 it can be seen that as the angle of attack increases, the magnitude of the force
increases and the centre of pressure gradually moves forwards towards the leading edge until the
point of stall when, with the aerofoil past its stalling angle of attack (or critical angle), the force
reduces and the CP moves rapidly rearwards. With a cambered aerofoil, the centre of pressure
movement over the normal operating range of angles of attack is no further forward than
approximately 25 - 30% chord, measured from the leading edge. With a symmetrical aerofoil
section there is virtually no movement of the CP over the working range of angles of attack, in
subsonic flight.
23. The movement of the CP with angle of attack is shown for a cambered aerofoil at
Figure 2-10.
FIGURE 2-10
Centre of
Pressure
Movement
Moment
25. The moment of a force about any point is the product of the force and the perpendicular
distance from the line of action of the force to that point. See Figure 2-11.
FIGURE 2-11
Moment of a
Force
Couple
26. Two equal forces acting parallel but in opposite directions are called a couple. The moment
of a couple is the product of one of the forces and the perpendicular distance between them. See
Figure 2-12.
FIGURE 2-12
Moment of a
Couple
Coefficients
27. When considering lift, drag and pitching moments, it is much more convenient to use their
respective co-efficients, CL,CD,CM. These co-efficients are non-dimensional and independent of
density, scale of the aerofoil and velocity prevailing at the time such studies are carried out. They
depend on the shape of the aerofoil and vary with angle of attack.
Aerodynamic Centre
28. An aircraft pitches about the lateral axis which passes through the centre of gravity. The
wing pitching moment is therefore the product of lift and the distance between CG and CP of the
wing. But, as we know, the position of the CP is not fixed and moves with changes in angle of attack
and therefore, calculation of the pitching moment is quite involved and complicated.
29. The pitching moment and hence its coefficient (CM) depends not only on the lift force and the
position of the CP, both of which change with change in angle of attack, but also the point about
which the moment is considered.
30. For example, if we take a point of reference arbitrarily towards the leading edge then the nose
down pitching moment about this point (B), increases with increasing angle of attack because,
although the centre of pressure movement is forward, its effect is less than that of the increasing lift
force, as shown in Figure 2-13.
FIGURE 2-13
31. Now, about a point towards the trailing edge (A) the nose up pitching moment increases
progressively with increasing incidence as shown at Figure 2-14.
FIGURE 2-14
Pitching Moment
Change About
Point A
32. It follows, therefore, that if about the leading edge, the nose-down pitching moment
progressively increases and about the trailing edge, the nose-up pitching moment progressively
increases, then there must be a point somewhere on the chord line between points A and B about
which there is no change in pitching moment with changes in angles of attack. This point is the
wing aerodynamic centre, shown at Figure 2-15 and is, at subsonic speeds, approximately at quarter
chord (ie. 25% chord from the leading edge).
FIGURE 2-15
Pitching Moment
About Wing
Aerodynamic
Centre
33. This can be represented graphically at Figure 2-16 which shows curves of CM plotted against
CL where, conventionally, nose-up pitching moments are referred to as positive, and nose-down,
negative.
FIGURE 2-16
Cm against C L
34. It can be seen from Figure 2-16 that at zero lift there is a residual pitching moment present.
It is negative, and, by definition, remains constant about the aerodynamic centre up to the stall (ie
CLmax). By reference to Figure 2-17 which shows the pressure distribution around our cambered
aerofoil section at its zero lift angle of attack, it can be seen that the resultant forces due to the
pressure reduction torwards the trailing edge on the upper surface and towards the leading edge on
the lower surface produce a nose-down (negative) pitching moment.
35. The pitching moment coefficient CM at the zero lift angle of attack is referred to as CMo as
shown in Figure 2-16.
FIGURE 2-17
Pressure
Distribution at
Zero Lift Angle of
Attack
Spanwise Flow
37. When an aircraft wing is producing lift the local static pressure on the upper surface is lower
than that on the lower surface. Air will flow from an area of higher pressure to one of lower
pressure. Since a wing is of finite length, this means that air will flow from the under surface, around
the wingtip, to the upper surface. Consequently, a spanwise flow of air occurs from the root
outwards towards the tip on the under surface, around the tip, and from the tip inwards towards the
root on the upper surface. The effect is illustrated at Figure 2-18.
FIGURE 2-18
Spanwise Flow
38. The flow at any point on the trailing edge leaving the upper surface will, therefore, be moving
in a different direction from that leaving the lower surface as shown at Figure 2-19.
FIGURE 2-19
Upper and Lower
Surface Flow
39. Thus the flow at the trailing edge of the wing where the upper and lower surface flows meet is
of a vortex nature and these vortices are continuously shed all along the trailing edge, shown at
Figure 2-20 in which the trailing edge is viewed from behind.
FIGURE 2-20
Trailing Edge
Vortices
FIGURE 2-21
Wing Tip Vortices
Induced Downwash
41. The effect of these trailing vortices is to produce a downward airflow, or downwash which
influences the whole flow over the wing with two important consequences:
(a) The effective angle of attack is reduced by the modified relative airflow and thus the
lift generated is also reduced. This is shown at Figure 2-22. Furthermore, the drag
characteristics of the wing are adversely affected and this induced or vortex drag will
be covered in detail in Chapter 3.
(b) The flow over the tailplane in a conventional aircraft design will be affected by the
downwash such that its effective incidence is also reduced with important
consequences in respect of longitudinal stability, which is covered fully in Chapter 8.
FIGURE 2-22
Downwash Effect
on Angle of Attack
42. The magnitude of the downwash is determined by the vortex formation which in turn is a
consequence of spanwise flow. Spanwise flow results from wing tip spillage, the magnitude of which
is determined by the pressure differential between upper and lower surfaces. In other words, any
parameter which increases the pressure differential will also increase downwash and its effects.
44. Theoretically a constant downwash condition along the span can be achieved if the lift
increases from zero at the tip to a maximum at the root in an elliptical fashion as shown in
Figure 2-23. Such a condition is highly desirable for the reduction of induced drag, (explained fully
in Chapter 3), and one way of achieving it is with a planform in which the chord increases elliptically
from tip to root. There are, however, manufacturing and structural difficulties with such a planform
and it has been found that a close approximation to elliptical spanwise lift distribution is possible
using a tapered wing with varying aerofoil section.
FIGURE 2-23
Elliptical Lift
Distribution
45. A convenient way to consider lift distribution is to use the ratio of the lift coefficient at any
given point on the wing span (the local lift coefficient) (Cl), to the overall wing lift coefficient (CL),
and plot this against the semi-span distance. When this is done for an elliptical planform wing a
constant value is obtained from root to tip since:
Cl
------ = 1.0
CL
46. Figure 2-24 shows spanwise lift distribution in this format for a number of wing planforms.
The elliptical planform (A) has only been used in a few cases, most notable being the Spitfire. The
rectangular planform (B) is often used for light private aircraft and trainers, because of its favourable
stall characteristics. Larger aircraft invariably use tapered wings, in order to limit structural weight
and maintain stiffness, with a taper ratio of between 20% and 45% (C) and (D).
FIGURE 2-24
Spanwise Lift
Distribution
Wake Turbulence
47. The trailing vortices produced by a wing when it is creating lift extend for a considerable
distance behind the aircraft. The greater the lift being produced, the stronger these vortices will be.
With a large aircraft these vortices create significant turbulence in the wake of the aircraft and take
several minutes to dissipate. This wake turbulence is sufficient to seriously affect the controllability
of other aircraft entering it and pilots are strongly advised to maintain a specified separation when
following a large aircraft, especially in close proximity to the ground (i.e. during the take-off and
landing phase). The separation required will depend upon the relative sizes of the aircraft and may
be several miles if the following aircraft is much smaller than the leading one.
48. In addition, the strength of the vortices is universally proportional to aircraft speed and
aspect ratio. The increased angle of attack, for a given weight, associated with low speed and
stronger vortices from a low aspect ratio wing will result in increased wake turbulence.
Furtheremore, when trailing edge flaps are extended, extra vortices are shed from the flap tips which
tend to weaken the tip vortices and hasten vortex breakdown.
49. The vortex strength will, therefore, be greatest with increased aircraft weight, reduced speed
and clean configuration ie. shortly after take-off.
50. This wake turbulence is influenced by proximity of the aircraft to the ground and also wind
conditions. The vortices slowly descend under downwash influence to approximately 1000ft below
the aircraft until when, in ground effect, they drift outwards from the generating aircraft’s track.
Any prevailing cross-wind, between 5-10kts, will retain the upwind vortex on the generating
aircraft’s track ie. on the runway after take-off.
Lift
51. Lift is defined as that component of the total aerodynamic force which is acting perpendicular
to the direction of flight. The magnitude of the total aerodynamic force, and therefore the lift
generated, is dependent upon a number of variables of which the following are the most important:
52. The last two variables, viscosity and compressibility of the air, and their effect on lift will be
discussed in subsequent chapters.
53. However, the major factors are dynamic pressure (½ρV²), wing surface area (S) and the
relative pressure distribution existing on the surface, ie. the coefficient of lift (CL).
L = CL ½ ρ V² S
CL for a given aerofoil section and planform allows for varying angle of attack and other variables
not included in the equation. By transposition of formula it can be seen that:
lift
C L = ----------------
1 2
--- ρV S
2
55. The coefficient of lift is the ratio of lift pressure to dynamic pressure.
57. Figure 2-25 shows a graph of CL against angle of attack (α) for a moderately cambered
aerofoil section. It will be seen that the curve is linear for the greater part, with the coefficient of lift
beginning to fall off at about +14°. The lift coefficient reaches a maximum value at about +15° (CL
max) as the section reaches stalling angle (αstall), otherwise known as the critical angle (αcrit).
Therefore any further increase in angle of attack results in marked reduction in CL.
FIGURE 2-25
Lift Curve
Effect of Camber
58. The slope of the CL/α curve is constant regardless of the camber of the aerofoil, but values of
CL are greater for any given angle of attack in sections of increased camber. This is illustrated at
Figure 2-26.
FIGURE 2-26
Effect of Camber
on the Lift Curve
59. Note that the curve passing through the origin at Figure 2-26 is representative of a
symmetrical wing section. At zero angle of attack such a section produces no lift since the pressure
distribution on the upper and lower surfaces is identical and there is thus no pressure differential. As
we know from our pressure distribution studies earlier in this chapter, the angle of attack at which
the CL is zero is known as the zero-lift angle of attack. For a symmetrical aerofoil it is 0° and for a
cambered section, typically between -2° and -4°.
FIGURE 2-27
Effect of Leading
Edge Radius on
the Lift Curve
FIGURE 2-28
Effect of Aspect
Ratio on the Lift
Curve
Effect of Sweepback
62. If an aircrafts wings are swept back and the wing area remains the same, the aspect ratio
2
( span /area) must be less than its equivalent straight wing. Therefore, the effect on the CL curve for
a swept wing compared to a straight wing is similar to that for a low aspect ratio wing when
compared to a high aspect ratio wing . This effect is shown at Figure 2-29.
FIGURE 2-29
Effect of
Sweepback on the
Lift Curve
63. Nevertheless, this does not account for the distinct reduction in CLMAX for highly swept
wings, however this is fully explained in Chapter 4, ‘Stalling’.
FIGURE 2-30
Effect of Leading
Edge Roughness
on the Lift Curve
FIGURE 2-31
Effect of Ice on
Leading Edge
67. This will almost certainly induce severe local pressure gradients, reducing boundary layer
velocity locally and possibly causing leading edge separation, with consequent loss of lift. Secondly,
some forms of ice have great surface roughness that significantly increases surface friction. This
reduces the boundary layer energy and increases drag. The overall effect is a decrease in the
maximum lift coefficient and an increase in drag.
68. The effects in practical terms are that the aircraft will require more power to maintain a given
airspeed, the stalling speed will be higher and the stalling angle of attack will be lower.
69. Leading edge icing is most likely to occur during flight in icing conditions and should be
prevented at the onset by the correct use of anti-icing procedures. Its effect will be most noticeable at
the low flight speeds associated with approach and landing, where the higher stalling speed will
require a higher landing speed.
71. The loss of boundary layer energy will lead to separation and a reduction in the stalling angle
of attack. The maximum lift coefficient will be reduced and stalling speed will be increased.
72. Surface coatings of frost can occur in flight, but are more commonly associated with ground
formation. Application of adequate ground de-icing and anti-icing procedures in conditions where
ice or frost may form on the upper surfaces of a parked aircraft are essential prior to flight. The loss
of lift and increased drag due to such coatings will seriously reduce take-off performance, to the
extent that the aircraft may have difficulty in becoming airborne. Even if it does, its climb
performance may be degraded to the point where obstacles cannot be cleared.
73. In addition to the foregoing, there is always a weight penalty associated with ice accretions on
the aircraft. The added weight means that airspeed must be higher or the angle of attack must be
increased to produce the extra lift required. The latter choice is a dangerous one, bearing in mind
that the ice will almost certainly have reduced the stalling angle of attack. It should also be borne in
mind that leading edge icing will probably have rendered the angle of attack indicator inoperative
and that the stall warning system does not compensate for the reduced critical angle.
74. Figure 2-32 shows the effects of ice and frost formation on the wing on the CL - α curve.
FIGURE 2-32
Effect of Ice and
Frost on C L
1
Lift = C L --- ρV 2 S
2
76. Wing area (S) does not change and. at constant altitude, density (ρ) remains essentially
constant. In order to maintain constant lift both the lift coefficient (CL) and speed (V) must be kept
constant or, if one increases the other must decrease proportionately. Since varying angle of attack
varies (CL), and the optimum angle of attack has been shown to be about +4°, maintaining constant
lift is best achieved by adjusting airspeed. The relation between the lift coefficient and speed, for
constant lift, is shown in the graph at Figure 2-33.
FIGURE 2-33
Lift Coefficient and
Airspeed
Relationship for
Constant Lift
77. During flight the weight will progressively decrease as fuel is used and the lift must decrease
accordingly, or the aircraft will climb. The ideal aerodynamic solution to this is to reduce airspeed
progressively, but in commercial operations, for ease of flight planning and other reasons, it is
normal to fly at constant speed and trim the aircraft to reduce angle of attack (incidence)
progressively.
QUESTIONS:
QUESTION 1.
QUESTION 2.
What is momentum?
QUESTION 3.
QUESTION 4.
QUESTION 5.
QUESTION 6.
What is the name of the line on an aerofoil which is equidistant from the upper and lower surfaces?
QUESTION 7.
QUESTION 8.
QUESTION 9.
QUESTION 10.
QUESTION 11.
If a wing chord measures 2m and the maximum thickness is 25cm, what is the thickness/chord ratio
as a percentage?
QUESTION 12.
What can you say about an aerofoil where the chordline and mean camber line are coincident?
QUESTION 13.
What is the name given to the angle between a wing chordline and the longitudinal centreline datum
of an aeroplane?
QUESTION 14.
For a cambered aerofoil, a typical angle of attack which will give zero lift is approximately what
angle?
QUESTION 15.
QUESTION 16.
What happens to the centre of pressure as the angle of attack of a cambered aerofoil increases?
QUESTION 17.
QUESTION 18.
For a cambered aerofoil, what pitching moment is produced at the zero lift angle of attack?
QUESTION 19.
In which directions does air tend to flow over the lower and upper wing surfaces?
QUESTION 20.
In general terms, what will be the stalling angle of attack of a low aspect ratio wing compared with a
high aspect ratio one of similar section?
ANSWERS:
ANSWER 1.
Chap 1 page 1
ANSWER 2.
Chap 1 page 2
ANSWER 3.
Chap 1 page 2
ANSWER 4.
Chap 1 page 2
ANSWER 5.
Chap 1 page 6
ANSWER 6.
Chap 1 page 8
ANSWER 7.
Chap 1 page 10
ANSWER 8.
Chap 1 page 12
ANSWER 9.
Chap 1 page 14
ANSWER 10.
Chap 2 page 6
ANSWER 11.
ANSWER 12.
ANSWER 13.
Chap 1 page 9
ANSWER 14.
Chap 2 page 6
ANSWER 15.
Chap 2 page 8
ANSWER 16.
Chap 2 page 9
ANSWER 17.
Chap 2 page 12
ANSWER 18.
ANSWER 19.
Chap 2 page 14
ANSWER 20.
Chap 2 page 22
Drag
3 Drag
1. The total drag force acting upon an aircraft in flight is the sum of all the components of the
total aerodynamic force that are acting parallel and opposite to the direction of flight. Total drag is
made up of those factors arising from the generation of lift (Lift Dependent Drag) and those which
are present when no lift is being generated (Zero Lift Drag).
Profile Drag
3. Otherwise known as boundary layer drag, profile drag is the term used to describe the
combined effects of boundary layer normal pressure drag (form drag) and surface friction drag.
Form Drag
4. We have already seen that when moving air is either totally or partially brought to rest on the
surface of an object, a pressure greater than static pressure, that is to say total, or stagnation
pressure, is acting on the surface of the body. The velocity differences between leading and trailing
edge mean that there are also pressure differences, pressure at the low velocity trailing edge being
greater than at the relative high velocity leading edge. This adverse pressure gradient opposes the
airflow across the surface, creating pressure drag. Form drag is otherwise known as boundary layer
normal pressure drag and can form a significant portion of the total drag force acting on the aircraft.
5. Consider a circular flat plate, which is placed in a wind tunnel so that the flat surface of the
plate is at right angles to the flow of air. If, over the entire surface area, the air was brought
completely to rest, a pressure equal to the dynamic pressure would be felt at all points. The force
thus created would be equal to the dynamic pressure multiplied by the surface area of the plate, or
½ρV²S, where S is the surface area.
6. The situation is complicated somewhat since the air is not brought totally to rest over the
whole surface. Some of the air flows around the edges, resulting in the formation of a low pressure
area behind the back of the plate. This effectively creates a suction, which tends to retard the airflow
passing the plate (or the passage of the plate through the air).
7. A turbulent wake will form behind the plate, in the case of a flat plate the amount of
turbulence will be considerable and the drag factor therefore will be extremely high. With a
streamlined wing the amount of turbulence will be much lower and therefore the drag factor will be
considerably reduced. We can therefore see that the shape as well as the frontal area will affect the
amount of drag produced. It is the shape, which gives us the co-efficient of drag (CD), and the total
form drag formula now reads:
1 2
Form Drag = C D --- ρV S
2
8. It is clear that a flat plate is a most inefficient shape to try and move through the air. If we
now consider a sphere of the same diameter as a flat plate placed in the airflow, it is not hard to
visualise that this shape will produce considerably less drag than the flat plate. The nature of the
airflow around these two objects is illustrated at Figure 3-1.
FIGURE 3-1
Airflow Around a
Flat Plate and
Sphere
9. It is seen at Figure 3-1 that the very large turbulent wake created by the flat plate has now
been replaced by a much smaller one as the air flows more smoothly around the surface of the sphere
and the suction drag created behind the sphere is thus reduced. The total amount of form drag
1 2
created by the sphere is calculated in exactly the same way ( C D --- ρV S ) , however the co-efficient of
2
drag for the sphere is very much smaller than that for the flat plate.
10. Now consider a streamlined aerofoil (ignoring any lift which it may generate), as illustrated at
Figure 3-2. This shape has a very low co-efficient of drag, since the air can follow the surface of the
shape almost to the trailing edge before it separates from the surface of the aerofoil and becomes
turbulent. The turbulent wake produced by a streamlined shape is therefore very small. It is not
possible to entirely eliminate the turbulent wake, but within limits the streamlined body can be
extended with a consequent reduction in the co-efficient of drag value.
FIGURE 3-2
Airflow Around a
Streamlined
Aerofoil
11. Clearly it would be impractical to extend the length of the aerofoil beyond certain sensible
limits since the increased weight would outweigh the improvement in the co-efficient of drag. In any
event, beyond a certain length, the effect of friction between the air and the aerofoil surface prevents
any further reduction in the drag factor. The amount of streamlining of a body is expressed as a
fineness ratio, which is its length divided by its maximum thickness, as shown at Figure 3-3.
FIGURE 3-3
Fineness Ratio
13. The coefficient of drag is the ratio of drag pressure to dynamic pressure.
14. Figure 3-4 shows a graph of CD against angle of attack (α). From this it can be seen that at
low angles of attack the drag coefficient is low and it changes only slightly with small changes of
angle of attack. As angle of attack increases however, drag increases and at the upper end of the α
range even small changes in angle of attack produce a significant increase in drag. At the stall a large
increase in drag occurs.
FIGURE 3-4
Drag Curve
FIGURE 3-5
Lift Curve
16. By combining Figure 3-4 and Figure 3-5 values of CL and CD for each angle of attack can be
obtained and the ratio CL/CD calculated for each angle. A graph of CL/CD ratio against angle of
attack can then be plotted, from which the best lift/drag ratio angle of attack is evident. Such a
graph is illustrated at Figure 3-6, from which it can be seen that the best lift/drag ratio occurs
typically at about +4°. At this angle the ratio of lift to drag is likely to be between 12:1 and 25:1,
depending upon the aerofoil section used and is referred to as the optimum angle of attack.
FIGURE 3-6
Lift/Drag Curve
17. At the zero lift angle of attack the lift/drag ratio is zero, but increases significantly for small
increases in angle up to the optimum angle of attack of about +4°. Beyond this the lift/drag ratio
decreases steadily since, although lift is increasing, drag is increasing at a greater rate. At the stall the
lift/drag ratio falls off markedly.
FIGURE 3-7
Boundary Layer
19. Within the boundary layer, and certainly within the free-stream air, it is hoped that the
airflow will be laminar from the leading edge almost to the trailing edge. At a point known as the
transition point, the smooth flow breaks down into a turbulent flow, which creates a much thicker
boundary layer, see Figure 3-8.
FIGURE 3-8
Transition Point
20. The effect of surface friction is, not surprisingly, far more marked in the turbulent part of the
boundary layer than in the laminar part. It is therefore desirable to hang on to the laminar flow for
a long as possible.
21. One of the main factors affecting the position of the transition point is the pressure
distribution of the upper surface of the wing. Transition tends to occur at the minimum pressure
point on the top surface, and this tends to occur at the point of maximum thickness of the wing itself.
Therefore, by designing a wing where the maximum thickness occurs well back from the leading edge
the laminar flow is increased, and the surface friction consequently reduced. A conventional wing
and a laminar flow wing are shown at Figure 3-9.
FIGURE 3-9
Aerofoil Sections
Interference Drag
22. Where two boundary layers meet, as at the junction between wing and fuselage, turbulent
flow will ensue, leading to an increased pressure difference between leading and trailing surface areas
and resulting pressure drag. The effect can be largely reduced in subsonic flight by adequate fairing
at the junctions.
FIGURE 3-10
Profile Drag -
Speed Curve
Induced Drag
25. As has been stated, the tip and trailing edge vortices create a downwash that angles the
relative airflow to the direction of flight. The effect of the vortices is to direct the airflow downwards
from the trailing edge. The angle between the airflow as it would be without induced drag, and the
actual airflow, is termed the downwash angle. See Figure 3-11.
FIGURE 3-11
Downwashed
Airflow
26. This induced downwash flow aft of the trailing edge influences the flow over the whole wing,
(see Chapter 2-41), such that the effective angle of attack is reduced. As a result, the lift generated is
also reduced and can only be restored by increasing the angle of attack. This increase in angle of
attack will tilt rearwards the total reaction vector and thus the component parallel to the direction of
flight is increased. This increase in drag, due to the wing vortices is induced (vortex) drag and is
shown in Figure 3-12.
FIGURE 3-12
Induced (Vortex)
Drag
27. Figure 3-12(a) represents a section of a two dimensional wing, ie. one of infinite span which is
producing lift, but has no trailing edge vortices.
28. Figure 3-12(b) represents the same section but whose wing is of a finite span and thus having
trailing edge vortices and hence induced downwash flow. The reduced effective angle of attack
results in a reduction in the lift generated as shown.
29. In order to restore the lift to its two dimensional value (ie. value without downwash as at
Figure 3-12(a), the angle of attack must be increased and the subsequent inclination of the total
reaction vector causes an increase in the component parallel to the direction flight (ie. induced drag).
Effect of Airspeed
30. The lift generated by a wing can be increased by increasing the angle of attack for a given
airspeed or by increasing the airspeed for a given angle of attack. The faster you fly, the lower the
angle of attack necessary for the lift required and, the lower the angle of attack the less the
downwash, thus reducing the induced drag, see Figure 3-13.
FIGURE 3-13
Effect of Speed on
Induced Drag
31. Suppose, whilst maintaining level flight, the airspeed were to be doubled. The dynamic
pressure producing lift (½ρV²) would be quadrupled. In order to maintain level flight the angle of
attack would have to be reduced, thereby inclining the lift vector forward and reducing induced drag.
Hence, induced drag decreases with increased airspeed being inversely proportional to the square of
the speed, as shown in the graph at Figure 3-14.
FIGURE 3-14
Induced Drag -
Speed Curve
FIGURE 3-15
Effect of Aspect
Ratio on Induced
Drag
33. The greater the aspect ratio, then, the lower the induced drag of the wing. Taken to its
ultimate conclusion, a wing of infinite span would have no induced drag at all. Clearly this is not
feasible in the practical sense, although it can be proved in a wind tunnel experiment with a wing
extending the full width of the tunnel. For aircraft in which low drag at moderate airspeed is a
fundamental requirement, high aspect ratio wings are essential. Examples are sailplanes, long range
patrol aircraft and medium speed transports.
Effect of Planform
34. Since induced drag decreases with increasing airspeed the need for high aspect ratio wings is
less important for aircraft designed to operate at high subsonic or supersonic speeds. Indeed, for
these a low aspect ratio is important because thin aerofoil sections are necessary, demanding a short
wingspan for structural reasons. Concorde, for example, has an aspect ratio of less than 1:1,
whereas a high performance sailplane may have an aspect ratio of 45:1 or greater. Clearly, with
aircraft in which normal operations demand a low aspect ratio, high induced drag at the low speeds
of take-off and landing has to be accepted. Similarly, training aircraft that benefit from the
favourable stall characteristics of a rectangular planform wing suffer from greater induced drag than
would be the case with a tapered wing. An elliptical planform gives the least induced drag for any
given aspect ratio. Sweep back has a similar effect on lift distribution to decreasing taper ratio. A
large sweep back angle tends to increase induced drag.
2
( CL )
C Di = -----------
πA
37. For any other planform a correction factor k is necessary, although a straight tapered wing
with a taper ratio of 2:1 approximates very closely to an elliptical wing. For planforms whose lift
loading is not elliptical k > 1. For conventional low speed wings the value of k is usually about 1.1 to
1.3.
38. The above equation for induced drag coefficient shows that:
(a) There is no induced drag on a wing of infinite span (two-dimensional flow only).
(b) The greater the aspect ratio, the less the induced drag.
39. Total drag is the sum of profile drag and induced drag and if the coefficients of total, profile
and induced drag can be represented as CD, CDP=and CDi=respectively, then
CD = CDP=+=CDi
from Paragraph 3-23 above , for a wing with elliptical loading
2
CL
C Di = ---------
πA
However, for any other load distribution
k CL 2
C Di = ----------- where k is the induced drag factor.
πA
k CL 2
Therefore C D = C Dp + -----------
πA
and now ------- can, for a given wing, be replaced by a constant K, so that,
k
πA
CD = CDp=+=K CL²
40. Assuming that CDp=is constant, which is valid over the normal operating range of angles of
attack, a graph of CD against CL² as at Figure 3-16, enables the factor K to be found and hence, for
a given wing, the induced drag factor k can be determined.
FIGURE 3-16
CD - CL² Curve
CL
α i = 18.24 -------
A
42. From the foregoing, if the influence of induced drag upon the graph of lift coefficient (CL)
against angle of attack (α) is considered, it will be seen from Figure 3-17 that the greater the induced
drag the shallower the CL - α curve. Curve A in Figure 3-17 represents a wing of infinite span, in
which there is no downwash (no induced drag) and therefore no reduction of the effective angle of
attack. Curve B represents a wing of finite span in which there is downwash (induced drag) and a
consequent reduction of the effective angle of attack. Curve C also represents a finite wing having
greater induced drag than wing B. As angle of attack increases, downwash increases and the effective
angle of attack progressively decreases. Hence the lift generated is less, at a given actual angle of
attack, the greater the induced drag of the wing.
43. The implication of this is that a wing of low aspect ratio, and therefore higher induced drag,
will have a higher stalling angle of attack than one of high aspect ratio and low induced drag. The
theoretical effect illustrated at Figure 3-17 is not as pronounced in practice.
FIGURE 3-17
Effect of Aspect
Ratio on Stalling
Angle of Attack
44. When considering the influence of induced drag upon the relationship between lift and drag
coefficients, the lift/drag ratio, it is seen from the graph of CL against CD at Figure 3-18 that as
induced drag increases, the slope of the CL – CD curve decreases, indicating reduced lift/drag ratio.
FIGURE 3-18
Effect of Aspect
Ratio on CL - CD
(Aeroplane Polar)
Ground Effect
45. During flight in close proximity to the ground the three-dimensional airflow pattern is
changed, since the vertical component of airflow is restricted, or eliminated altogether. This modifies
the upwash, downwash and tip vortices and therefore has a significant effect upon lift and drag.
46. Assuming the same lift coefficient is maintained, as a wing enters ground effect the upwash,
downwash and tip vortices are all reduced, as shown in Figure 3-19. The wing is now behaving as
though its aspect ratio had been increased and, as a consequence, its induced drag coefficient (CDi)
and induced angle of attack (αI) are both less for the same lift coefficient (CL).
FIGURE 3-19
Ground Effect
47. For ground effect to be significant the wing must be at a height considerably less than the
span of the wing. When height is equal to half-span the reduction in induced drag coefficient is less
than 10%, but at a height equal to quarter-span this value rises to almost 25%. This is illustrated at
Figure 3-20.
FIGURE 3-20
Effect of Height on
Induced Drag
Coefficient
48. Because the tip, or trailing vortices are reduced when a wing is in ground effect the spanwise
distribution of lift is altered and the induced angle of attack (αI) is reduced. Consequently a lower
angle of attack (incidence) is necessary to produce the same lift coefficient. In the graph of CL
against α at Figure 3-21 it will be seen that the slope of the curve is increased when the wing is in
ground effect. A lower angle of attack is needed for a given lift coefficient, or greater lift is generated
for a given angle of attack. It should be noted that, when in ground effect, the stalling angle of attack
is reduced.
FIGURE 3-21
Influence of
Ground Effect on
the Lift Curve
49. It will be appreciated that, for normal flight operations, ground effect is only of significance
during landing and take-off. The general effects are an increase in lift if a constant pitch attitude is
maintained and an increase in speed if the same power is maintained.
50. Furthermore, the reduced downwash affecting the tailplane will result in a greater
contribution to longitudinal stability and, as the download of the tailplane reduces, there will be a
nose down pitching moment change. However, if the aircraft is of a high tail design, then any
changes in downwash will not affect the tailplane and hence have no effect on longitudinal stability
or trim.
51. Pressure changes at the pressure source associated with changes in upwash and downwash
due to ground effect, will usually cause an increase in static pressure sensed and therefore a reduction
in indicated airspeed and altitude.
Effect on Landing
52. During the final stages of the landing approach there will be a tendency for the aircraft to
float beyond the intended touchdown point if it is brought into ground effect at a constant angle of
attack. The float distance may be considerable if speed is at all excessive.
Effect on Take-Off
53. The main danger from ground effect during take-off arises from the fact that, if constant
angle of attack is maintained, a loss of lift may be experienced as the aircraft leaves ground effect. It
is essential to delay rotation until the recommended airspeed is attained. Otherwise, in marginal
conditions such as high all-up weight, high ambient air temperature and/or low ambient density, it
may prove impossible to climb out of ground effect.
FIGURE 3-22
Effect of Wing Tip
Design
Winglets
56. At the wing tip there is a significant sidewash in the form of outwash below the lower surface
and inwash over the upper surface. By mounting a winglet vertically at the wing tip, advantage can
be taken of this sidewash in that the winglet will generate a lifting force, a component of which acts
in the direction of flight, opposing drag. The main tip vortex now forms at the tip of the winglet,
above the main wing, so that downwash from the main wing is reduced. Thus, induced drag is
reduced due to the reduction of the trailing vortices. The effect is illustrated at Figure 3-23. Winglets
can be mounted either above or below the wing tip, or both. However, winglets below the tip are
unusual because by mounting them upwards takes full advantage of upwash.
FIGURE 3-23
Effect of Winglets
FIGURE 3-24
Effective Angle of
Attack Spanwise
Wash-Out
58. The wing is attached to the fuselage of the aeroplane at a particular angle of incidence. If the
angle is maintained throughout the span of a tapered wing, the situation described in the preceding
paragraph will exist. If, however, the angle of incidence is progressively decreased toward the tip a
constant effective angle of attack can be maintained. Decreasing the angle of incidence from root to
tip is known as wash-out. The reverse is known as wash-in.
Change of Camber
59. The same effect as that produced by wash-out can be achieved by a progressive reduction of
camber from root to tip.
Total Drag
60. Of the two types of drag to which an aircraft is subjected, profile drag increases with
increasing airspeed, whilst induced drag decreases with increasing airspeed. By plotting both on a
graph, it is possible to establish a speed at which the sum of the two is a minimum. This is the speed
for minimum drag V MD .See Figure 3-25.
FIGURE 3-25
Effect of Speed on
Drag
FIGURE 3-26
Effect of Altitude
on Drag - EAS
Curve
1
62. However, for a given EAS, the TAS with increasing altitude increases by the factor ------- , where
σ
σ is the relative density, and therefore, if drag is now plotted against TAS, the curve is mirrored
progessively to the right with increasing altitude. See Figure 3-27.
FIGURE 3-27
Effet of Altitude
on Drag - TAS
Curve
Speed Stability
63. Stability, which is fully explained in Chapter 8, is the study of the aircrafts response following
a disturbance and its tendency thereafter to return, or otherwise, to its pre-disturbed condition.
When considering speed stability, refer.ence is made to the drag curve shown at Figure 3-27.
Effect of Speed
Changes on Drag
64. Consider an aircraft flying at speed A. In straight and level flight thrust equals drag and so
the thrust required can be indicated by the horizontal line T1. If now there was an un-demanded
speed increase from A to B, with the thrust remaining as it was, the drag exceeds the thrust and so
the speed will reduce to A. Conversely, if the speed reduces to C, with the thrust remaining constant,
the thrust exceeds the drag and so the speed will increase.
65. This then is a speed stable situation, which will always exist on the front side of the drag
curve, ie. at speeds in excess of VMD.
66. Now consider the same situation on the back side of the drag curve, in other words where the
aircraft is flying at a speed which is lower than VMD. Initially the speed is D and the thrust T2.
67. If the speed increases to E the drag decreases, the thrust exceeds the drag and so the speed
increases further. This is bad enough, but now consider a drop in speed from D to F. The drag has
increased, the thrust is constant and so the speed decreases further; the drag is increased, the thrust is
insufficient and so on. This then is definitely a speed unstable situation.
68. The effect of increasing profile drag, such as the use of undercarriage or speed brake, will not
alter the induced drag curve, but will steepen the profile drag curve. Thus the point of intersection,
and hence VMD, reduces (although the total drag increases). Thus the speed range where the aircraft
is speed stable will be greater.
69. The speed-instability situation below VMD is particularly important with modern jet
transport aircraft. This is because of the high weights involved, the high angles of attack at the low
airspeeds involved in the approach phase and the slow reaction times of jet engines, when compared
with piston engines.
70. When dealing with induced drag it was seen that an increase in weight resulted in an increase
in induced drag. Since the intersection of the profile and induced drag lines gives VMD we can
therefore see, at Figure 3-28, that VMD increases as the weight increases and speed stability
correspondingly reduces.
FIGURE 3-28
Effect of Weight
on Speed Stability
71. Using the same sort of logic it can be seen that the higher the aspect ratio the lower the VMD
and speed stability therefore increases.
Stalling
Stalling Speed
Initial Stall in the Spanwise Direction
Stall Warning
4 Stalling
1. The stalling characteristics for large transport aeroplanes are laid down in JAR 25. The
following are the relevant extracts:
During the approach to the stall the longitudinal control pull force should increase continuously as
speed is reduced from the trimmed speed to approximately 1.1Vs. At speeds below 1.1Vs some
reduction in longitudinal control pull force will be acceptable provided that it is not sudden or
excessive.
In level wing stalls the bank angle may exceed twenty degrees occasionally, provided that lateral
control is effective during recovery.
For stalls from a thirty degree banked turn with an entry of one knot per second, the maximum
bank angle which occurs during recovery should not exceed approximately sixty degrees in the
original direction of the turn, or thirty degrees in the opposite direction.
For dynamic stalls (that is those with a faster entry) the maximum bank angle which occurs during
the recovery should not exceed approximately ninety degrees in the original direction of the turn,
or sixty degrees in the opposite direction.
Deep Stall Penetration. Where the results of wind tunnel tests reveal a risk of a catastrophic
phenomenon (eg. superstall, a condition at angles beyond the stalling incidence from which it
proves difficult or impossible to recovery the aeroplane), studies should be made to show that
adequate recovery control is available at and sufficiently beyond the stalling incidence to avoid
such as phenomenon.
It must be possible to produce and to correct roll and yaw by unreversed use of aileron and rudder
controls up to the time the aeroplane is stalled. No abnormal nose-up pitching may occur. The
longitudinal control force must be positive up to and throughout the stall. In addition it must be
possible to promptly prevent stalling and to recover from a stall by normal use of the controls.
For level wing stalls, the roll occurring between the stall and the completion of recovery may not
exceed approximately twenty degrees.
For turning flight stalls, the action of the aeroplane after the stall may not be so violent or extreme
as to make it difficult, with normal piloting skills, to effect a prompt recovery and to regain control
of the aeroplane.
2. When considering surface friction drag in the previous chapter the boundary layer was
discussed and illustrated. It was seen that the boundary layer airflow is normally laminar over most
of the wing surface, becoming turbulent at a point known as the transition point.
4. The point on the surface where airflow ceases is known as the separation point. Beyond this
point the adverse pressure gradient will cause the airflow adjacent to the surface to reverse in
direction, becoming eddying and turbulent with the mean velocity of the airflow in the opposite
direction to the free stream airflow. Aft of the separation point little or no lift is generated.
FIGURE 4-1
Boundary Layer
6. As the angle of attack is increased the adverse pressure gradient on the upper surface increases
and boundary layer separation begins to occur near the trailing edge. Further increase in the angle of
attack will cause the separation point to move forward towards the leading edge, reducing the
amount of lift generated. Eventually an angle of attack will be reached at which flow over the upper
surface of the wing breaks down completely. The lift coefficient ceases to rise and starts to fall if
angle of attack is increased further. This is known as the critical, or stalling, angle of attack and is
illustrated in the lift curve at Figure 4-2. The drag coefficient increases with increasing angle of
attack, rising steeply at the stalling angle, as illustrated at Figure 4-3. The lift/drag ratio falls steeply
at the stalling angle of attack.
FIGURE 4-2
Lift Curve
FIGURE 4-3
Drag Curve
FIGURE 4-4
Leading Edge
Separation
Pitching Moments
9. The effect of the centre of pressure movement on the wing is to produce an increasing pitch-
up moment up to the stall, followed by a marked pitch down moment as the CP moves rapidly aft at
the stall. The pitching moments on the aeroplane as a whole will depend upon the configuration of
the wing and tail surfaces. It is clearly desirable that there should be a nose-down pitching moment
at the stall, since this will automatically reduce the angle of attack and assist in recovery from the
stall. Loss of downwash over the tailplane (horizontal stabiliser) at the stall may achieve this in
aeroplanes where the nose-down pitching moment of the wing section is negated by other factors.
Pre-Stall Buffet
10. As the disturbed wake, arising from the separated flow behind the wing, strikes the tail
surfaces it causes aerodynamic buffeting on the control surfaces (elevator and rudder) which can
usually be felt at the control column and rudder pedals, giving warning of the incipient stall. The
effectiveness of this as a warning will depend to a large extent upon the location of the tail surfaces
with respect to the turbulent wake. The effectiveness of the controls may well decrease as separation
occurs. This is often particularly true of the ailerons, situated as they are at the trailing edge of the
wing.
Stalling Speed
11. In straight and level flight the weight of the aircraft is balanced by the lift generated and Lift =
1 2
C L --- ρV S . Given constant density and wing area the variables are, as we have seen, C L and V.
2
If airspeed (V) is reduced, by throttling back the engine, C L will have to be increased by increasing
the angle of attack, if level flight is to be maintained at the reduced speed. This practice has its limits
since, if pursued, an IAS will be reached where increasing the angle of attack will mean that the
stalling angle is reached. The speed at which this occurs is the stalling speed.
12. The speed corresponding to a given angle of attack, or rather lift coefficient, can be derived
from the lift formula:
1
Lift = CL --- ρV 2 S
2
13. Therefore:
Lift
V 2 = ------------------
1
C L --- ρS
2
14. Therefore:
Lift
V = ------------------
1
C L --- ρS
2
15. Since the stall occurs when the coefficient of lift is at its maximum value (CLmax), the formula
for the stalling speed (Vs) is:
Lift
Vs = ---------------------------
1
C Lmax --- ρS
2
16. The only variables in this formula are speed and lift, so stalling speed is proportional to the
square root of lift:
V s ∝ Lift
18. In straight and level flight lift = weight, so by substitution the formula for the basic stalling
speed (VB) will be:
Weight
VB = ---------------------------
1
C Lmax --- ρS
2
19. The actual stalling speed will differ from the basic stalling speed if the conditions by which it
is defined are not met. The factors which will cause variation from VB are:
(c) power
21. The formula for calculating the increased stalling speed for a given increase in weight is
derived from the basic stalling speed formula as follows:
W
VB = ---------------------------
1
C Lmax --- ρS
2
22. Let us assume that the basic stalling speed at an aircraft weight of W is V and for an
1 S1
increased weight W is VS . The ratio of the two stalling speeds at the two different weights is:-
2 2
W2
---------------------------
1
V S2 C Lmax --- ρS
2
--------- = -------------------------------
V S1 W1
---------------------------
1
C Lmax --- ρS
2
23. Since the two denominators on the right hand side of the equation are the same:
V S2 W2
--------- = --------
V S1 W1
24. Therefore:
W2
V S2 = V S1 --------
W1
Example
25. Given a stalling speed of 120 kt for an aircraft at 150,000 kg, the approximate stalling speed
at 180,000 kg is:
L
-----
W
L
---------------------------
1
VM C Lmax --- ρS
2
-------- = -------------------------------
VB W
---------------------------
1
C Lmax --- ρS
2
29. Again, the denominators on the right hand side of the equation are equal so:
VM L
-------- = -----
VB W
VM
-------- = n
VB
31. Or
V M = VB n
FIGURE 4-5
Forces in a Steady
Co-ordinatd Turn
32. Figure 4-5 illustrates the forces acting upon an aircraft in a banked turn, at bank angle θ .
From this it can be seen that:
W1 W
cos θ = -------- = -----
L L
33. Therefore:
1 L
------------ = ----- = n
cos θ W
1
VM = V B ------------
cos θ
Example
35. In a 60° banked turn the increase in stalling speed (VM) over the basic stalling speed (VB) will
be:
1
V M = V B -------
0.5
V M = VB 2
36. Therefore:
V M = V B × 1.4
37. The manoeuvre stalling speed in a 60° banked level turn is 1.4 times the basic stalling speed.
39. The decrease in stalling speed with power on is due to the vertical component of thrust, which
is significant at the high angles of attack involved, and which obviously applies to either pure jet or
propeller driven aircraft. With propeller driven aircraft the effect of the propeller slipstream over the
wing will also delay the stall. The slipstream may, however, prevent the wing behind the power units
from stalling (the inboard sections), thereby leaving the tips to stall first despite the best efforts of the
aeroplane designer.
40. It should be noted that recovery from a power-on stall is likely to involve less height loss since
power unit response will be faster.
42. With the centre of gravity well forward of the centre of pressure, a considerable download is
required at the tailplane to maintain level flight. The lift produced by the wing is therefore required
to support not only the aircraft weight but also the download produced by the tail. For a given
weight, the further forward the centre of gravity the greater the angle of attack required at any given
airspeed, and therefore the higher the speed at which the stalling angle is reached.
43. Notwithstanding the higher stall speed with the forward C of G, the further forward the C of
G the easier the stall recovery, since the weight of the aircraft is helping the pilot to lower the nose of
the aircraft as an essential part of the recovery procedure. In other words, if the C of G is to the rear
of the permitted envelope, stall recovery may well be impossible.
1 2
L = CLmax --- ρV S
2
45. We know that CLmax and S are constant at the stalling angle, and we also know that indicated
1 2
airspeed is given by dynamic pressure --- ρV . It therefore follows that any aircraft will stall at a
2
constant IAS, regardless of altitude. This of course assumes constant weight and aircraft
configuration, and straight and level flight. The statement also ignores the very small variations in
the difference between equivalent and indicated airspeed as altitude is changed.
Tip Stall
47. As mentioned earlier, at the point of the stall the centre of pressure moves rapidly aft on the
wing, which gives a nose-down pitch. This reduces the incidence of the wing, which will therefore
once again produce lift, a desirable self-correcting characteristic.
48. A wing does not normally stall over its entire length simultaneously, the stall commencing
from one part of the wing. Having commenced at one point on the wing the stall then spreads over
the remainder of the wing. The main factor governing the point at which the stall commences is the
shape of the wing. It is undesirable that a wing stalls from its tip first as this may lead to control
difficulties. Any tendency to drop a wing at the stall may well lead to spinning, especially if the stall
recovery procedure is badly executed. Once the wingtip is dropping, the downward motion increases
the effective angle of attack, deepening the stall on that wing, whilst the effective angle of attack of
the upgoing wing is decreased, inhibiting the stall. This worsens the situation by increasing the rate
of roll. Clearly, tip stall is an undesirable characteristic.
49. Further advantages of having a wing stall first from its root instead of the tip, are that aileron
control can be maintained up to the point of full stall, and that the separated flow from the wing root
may cause buffet over the tail which provides a stalling warning.
50. The principal techniques for ensuring that the stall occurs initially at the wing root are
discussed below:
51. The wing may be twisted so that the tip is at a smaller angle of incidence than the root, this
will ensure that the root reaches its stalling angle before the tip. This decreasing angle of incidence
from root to tip is termed wash-out.
52. The same effect as that produced by wash-out can be achieved by a progressive reduction of
camber from root to tip.
53. A stall inducer, stall strip or root spoiler, may be fitted at the inboard end of the wing, as
shown at Figure 4-6. The strip has very little effect on the airflow at normal angles of attack,
however at high angles it spoils the airflow over the wing behind it, causing ‘buffet’ on the tailplane
and ensuring this section of the wing stalls first.
FIGURE 4-6
Stall Strip, Stall
Inducer or Root
Spoiler
54. Wing platform has a significant effect upon stall characteristics. Figure 4-7 shows various
platforms and the stall progression associated with each.
FIGURE 4-7
Effect of Planform
on Stall Pattern
55. Wing tip shape will also influence tip stall characteristics. Rounded tips, as seen on many
WW II fighters, or chamfered tips as seen on the Islander and Dornier 228, stabilise the wingtip
vortices at high angles of attack (incidence).
Use of Ailerons
56. The downgoing aileron increases the camber and therefore steepens the slope of the C L – α
curve. It therefore produces a small reduction of the stalling angle of attack at that part of the wing
to which it is attached, usually near the tip. Consequently, the use of aileron when flying at a high
angle of attack close to the stall may initiate tip stall on that side. In addition, when tip stall occurs,
the downgoing aileron loses effectiveness which will probably worsen the situation.
Swept Wings
57. From Figure 4-7 it can be seen that swept wings are particularly prone to tip stall, the greater
the sweepback the greater the tendency.
58. The primary purpose of sweepback is to increase the value of the critical Mach number for a
given aircraft. The effects of compressibility at speeds approaching the critical Mach number on the
performance of an aircraft are discussed at length in Chapter 11 dealing with high-speed flight.
59. The basic problem is that, if the air over any part of the aircraft structure (usually the wing)
reaches the speed of sound there is an excessive rise in drag due to compressibility effects. The actual
free air speed at which the accelerated air over the wing goes supersonic is known as the critical
Mach number. Figure 4-8 shows a straight unswept wing travelling at a true airspeed corresponding
to Mach 0.8. Note that the air that is accelerated over the top surface of the wing is travelling at
Mach 0.85.
FIGURE 4-8
Unswept wing at
MO.8
60. Figure 4-9 shows a swept wing, again travelling through the air at Mach 0.8. As before, the
acceleration of air over the top surface means that the speed of Mach 0.85 is achieved on the top
surface in the direction of the airflow. However, only the component of the relative airflow across the
wing that is perpendicular to the leading edge can be considered as creating lift. Consequently, only
the vector speed of this chordwise component is significant when considering critical Mach number.
FIGURE 4-9
Swept Wind at
MO.8
61. The wing shown at Figure 4-9 is travelling at the same speed through the air as the wing at
Figure 4-8. The accelerated air at right angles to the leading edge of the swept wing is travelling
slower than the equivalent air across the straight wing, by 11% of the local speed of sound. Another
way of looking at this is that the aerofoil section along the chord line (shown dashed at Figure 4-9 is
thinner than its equivalent on an unswept wing. Hence the acceleration of airflow over the upper
surface is less and the local velocity is lower.
62. At 35,000 ft (standard atmosphere) the local speed of sound is 575 kts and so 11% of this is
63 kt. Clearly the ability to fly 63 kts faster before reaching criticality is a big reason for using a
swept wing. You don't have to spend too long looking at modern jet transport aircraft to realise that
the manufacturers agree with this philosophy.
63. As already mentioned, the amount of lift generated by the wing depends upon the flow
perpendicular to the leading edge. In view of this and all other things being equal, less lift will be
produced by a swept wing than by a straight wing of equal area. To regain this lost lift, the angle of
attack has to be increased when a swept wing is used. The lift curves (co-efficient of lift against angle
of attack) are shown for both types of wing at Figure 4-10.
FIGURE 4-10
Effect of
Sweepback on the
Lift Curve
64. It is readily seen at Figure 4-10 that the higher the angle of attack, the bigger the difference in
the amount of lift generated. High angles of attack are associated with low speeds and the effect is
most evident on the approach to land in swept wing jet aircraft, where a very high nose-up attitude is
necessary.
65. Returning once more to Figure 4-9, the total airflow over the swept wing is shown broken
down into a chordwise vector and a spanwise vector. The flow of air outwards along the wing causes
the boundary layer on a swept wing to drift outwards towards the wing tip. This results in an
undesirably thick boundary layer in the region of the wing tip.
66. We know that the retardation of the air by the boundary layer is one of the major causes of
the stall and perhaps now we can now perhaps see an extremely undesirable situation evolving. A
thick boundary layer will encourage the stall. The boundary layer is thicker at the wing tip and
therefore the tip is likely to stall before the root. The undesirability of tip stall has already been
discussed. Quite obviously then, something needs to be done to prevent this migration of the
boundary layer outwards to the wing tip.
67. One simple way of preventing spanwise flow is to put a physical barrier in the way, as shown
at Figure 4-11. This device is known as a wing fence.
FIGURE 4-11
Wing Fence
68. Spanwise flow can also be reduced by means of a saw tooth leading edge as shown at
Figure 4-12, or a notched leading edge as shown at Figure 4-13. Both of these devices produce a very
marked vortex that inhibits the spanwise flow.
FIGURE 4-12
Sawtooth Leading
Edge
FIGURE 4-13
Notched Leading
Edge
69. Because tip stall is reduced, the pitch up tendency at the stall will also be reduced, however
there are other benefits to be derived from the saw tooth leading edge. Since the thickness/chord
ratio of the tip area is reduced, the critical Mach number will be increased. Furthermore, the centre
of pressure of the extended wing is further forward than it would otherwise be and therefore the
mean centre of pressure of the whole wing is further forward. Consequently, when the tip eventually
stalls, the forward movement of the centre of pressure is less marked, giving a less pronounced pitch
up moment.
70. By causing a vortex in the wing section behind the notched leading edge, the magnitude of the
vortex over the tip area is reduced, and with it the magnitude of the tip stall.
71. Sometimes the notched leading edge is used in conjunction with the saw tooth leading edge
extension. This intensifies the inboard vortex behind the devices and thus a stronger restraining
effect upon the boundary layer outflow.
72. Having suggested that the production of a vortex will inhibit the spanwise flow, it should
come as no surprise that the final means of arresting this flow which we consider is the use of vortex
generators. These are quite simply small metal plates which are mounted edge on to the airflow and
which produce vortices behind them. The vortices are small, thus incurring small drag penalties, but
they act by bringing down the fast-moving air above the boundary layer. This adds kinetic energy to
the boundary layer, enabling it to better cope with the adverse pressure gradient. This is shown at
Figure 4-14.
FIGURE 4-14
Vortex
Generators
73. Despite the use of some or all of these devices it is inevitable that, with a significantly swept
wing, the tips will stall first, and that the stall will then spread inwards towards the roots. As this is
happening the total lift generated by the wing is reducing, the centre of pressure is moving inwards
and, because of the sweepback, the centre of pressure moves forward. This is shown at Figure 4-15.
FIGURE 4-15
Effect of Tip Stall
on Centre of
Pressure
74. With a straight wing aircraft the nose tends to drop at the stall, and this is obviously
desirable. With a swept wing aircraft the nose tends to pitch up at the stall, because of the forward
movement of the centre of pressure, and this is obviously undesirable, since it may lead to a deep stall
condition.
75. When a swept wing is subjected to increased loading, as in a turn, the structural nature of the
wing produces not only an upwards bend but a twist as well. This is caused by the sweepback
placing most of the outboard structure of the wing behind the main structural member, and the result
of this is to reduce the angle of attack of the tip. As the angle of attack is reduced, the amount of lift
being generated by the tip is also reduced and the centre of pressure of the wing moves inwards
towards the root. As with the stall, movement of the centre of pressure inwards also means that it
moves forward, and the overall result of this is that in a turn the nose of a swept wing aircraft tends
to pitch up.
Stall Warning
76. It is required that adequate advance warning of the stall is available (the margin) in order that
early corrective action may be taken. In light aircraft warning of approach to the stall is usually
achieved aerodynamically in the form of buffet. Where this is absent, or could be confused with
turbulence, the stall warning is artificially induced. In heavy aircraft with powered controls it is
normal to incorporate a stick shaker. This device shakes the stick in order to simulate the effect of
the turbulent airflow over the elevators which would normally be felt at the stick as pre-stall buffet,
but which is masked by the electro-hydraulically powered control system. Stick shakers are operated
from a detector that senses incidence (angle of attack) and rate of change of incidence. Having gone
this far it is normal to incorporate also a stick pusher. If the pilot doesn't respond to the stick shaker,
the stick pusher automatically ensures that the correct incipient stall recovery procedure is initiated.
77. Following a stall warning the recovery action is to reduce incidence to below warning
activation value and at the same time apply maximum power to minimise height loss. If the stall has
occurred the recovery action is the same, but if wing drop occurs, lateral correction should not be
applied until after the wings are unstalled since the application of aileron before the wings are
unstalled will probably aggravate the wing drop. It should be appreciated that recovery at the
warning stage will involve less height loss.
79. Where the angle of attack sensor is required to activate a stick shaker or stick pusher, as well
as a stall warning, a more precise type of sensor device is used. In most cases this consists of an
aerodynamic vane protruding from the side of the fuselage near the nose, as shown at Figure 4-16.
The vane is attached to the rotor of a synchro, which is free to rotate. The synchro and vane are
initially aligned against reference marks on the fuselage representing the aircraft pitch attitude when
the aircraft is ‘clean’ with the wings at the most efficient incidence. The output from the synchro is
transmitted to an electrical circuit controlling the stall warning systems. The circuit usually includes
an input from the flap position monitoring system, to compensate for the pitch attitude change that
occurs when flaps are deployed. The circuit is de-energised when the aircraft is on the ground.
FIGURE 4-16
Angle of Attack
Vane
Stick Shakers
80. The vane-operated synchro output circuit is programmed to detect not only incidence, but
also rate of change of incidence. It feeds a signal to the stick shaker motor when either parameter
indicates an approach to the stall. The motor drives an unbalanced ring attached to the control
column. This causes the column to vibrate at a frequency similar to that caused by aerodynamic
buffet. In many aircraft an audible warning accompanies the stick shaking, in case the aircraft is on
autopilot at the time. The recovery procedure is to reduce incidence, preventing the stall from
developing.
Stick Pushers
81. This somewhat controversial device automatically takes the recovery procedure described
above, by pushing the control column forward if the stalling incidence is reached. Stick pushers are
sometimes fitted in aircraft that are prone to what is known as the deep stall, or super-stall condition.
Broadly speaking, these aircraft have swept back wings, high-speed wing sections and the ‘T’ tail
configuration.
82. The airflow following a stall in a conventional aircraft is illustrated at Figure 4-17. It can be
seen that, although the air has broken away in a random manner from the upper surface of the wing,
the tailplane and the elevators are still in undisturbed air. Consequently the tailplane will produce
the lift required for stall recovery, especially with the elevator fully down.
FIGURE 4-17
Stall -
Conventional
Aircraft
83. Figure 4-18 shows the airflow in the stall for a swept wing ‘T’ tail aircraft. In this case the
turbulent air completely covers the tailplane and elevators, making them virtually ineffective.
FIGURE 4-18
Deep or Super
Stall
84. Additionally, the swept wings progressively stalling from tips to root causes a nose up
pitching movement, which the ineffective back end is quite incapable of combating.
85. The problem is further aggravated by the fact that the aircraft will by now have acquired a
significant downward vertical velocity, which will progressively increase the angle of attack beyond
the stalling angle.
86. Finally, it is often the case with ‘T’ tail aircraft that the engines are mounted on the rear
fuselage. Now the chances are that the turbulent air entering the jet intakes will have caused a
flameout.
87. Remember that the stick pusher, which is activated by an angle of attack sensor, is there to
prevent the stall occurring in the first place.
Speed Margin
88. The margin between the stall speed and the limiting Mach number, known as the speed
margin, is relatively small at the high altitudes that give optimum efficiency in terms of jet operation.
Remember that as altitude increases the air temperature decreases, the local speed of sound
decreases, and therefore the TAS corresponding to a given Mach number decreases. Conversely,
since the stall speed in terms of IAS remains constant with change of altitude, as the aircraft climbs
the TAS at which the stall occurs will increase. This situation is illustrated at Figure 4-19.
FIGURE 4-19
Effect of Altitude
on the Speed
Margin
89. Bear in mind that jet streams and associated clear air turbulence occur at or around the
tropopause. It should then be obvious that a great deal of care must be taken to keep the cruising jet
aircraft speed stable, and to prevent unchecked oscillatory motions about any of the aircraft axes.
Canard Configuration
90. In the canard configured aircraft the stabiliser is mounted forward of the mainplanes (it is a
‘tail first’ aircraft). Unlike the conventional configuration, in which only the mainplanes (wings)
provide positive lift, in the canard both sets of surfaces provide positive lift, as shown at Figure 4-20.
The stabiliser is at a slightly greater angle of incidence than the wing so, when the aircraft pitches up
the canard foreplane produces a restoring nose-down pitching moment. Because the foreplane will
reach the stalling angle of attack before the mainplane it has been claimed that the canard configured
aircraft is unstallable, since the stalled foreplane will cause the nose to drop, automatically initiating
stall recovery. Unfortunately this does not hold good during violent manoeuvres, when both planes
may stall. With no effective control surfaces the aircraft is then uncontrollable and stall recovery
may be impossible.
FIGURE 4-20
Canard
Configuration
Stall Recovery
91. Recovery from the stall invariably requires the angle of attack to be reduced, possibly to well
below the stalling angle, in order to restore lift. During this process it is likely that a considerable
amount of height will be lost.
FIGURE 4-21
Climbing Turn
93. In a descending turn the wing on the outside of the turn travels faster, but the wing on the
inside of the turn has the greater effective angle of attack and is therefore closer to the stalling angle.
This is illustrated at Figure 4-22. In the event of a stall in a descending turn the aircraft is liable to
roll further into the turn, which could then rapidly develop into a spin.
94. It should be appreciated that recovery from a stall where wing-drop has occurred will require
more height for recovery since extra time is required to level the wings after reducing incidence. This
will be more pronounced during recovery from a stall in a descending or climbing turn.
FIGURE 4-22
Descending Turn
The Spin
95. If a wing drop occurs at the stall, a spin may develop. The angle of attack of the dropping
wing is increased well beyond the stall, due to the downward vertical velocity. Conversely the
upgoing wing will experience a reducing angle of attack, and will be less deeply stalled, or even
unstalled. Because of the almost non-existent lift experienced by the downgoing wing it will continue
to drop, and any attempt to raise it using the ailerons will aggravate the situation by further
increasing the angle of attack at the outboard end of the downgoing wing.
96. It does not, however, occur in isolation. At the same time as roll is occurring, yaw is also
occurring due to the increased drag on the downgoing wing. This increased rolling and yawing
motion is known as autorotation, often referred to as the incipient spin.
97. Once the rolling and yawing motions become self-sustaining, the aircraft is spinning. This is
shown at Figure 4-23.
FIGURE 4-23
Autorotation
Leading to the
Spin
98. Recovery from the spin is aimed at reducing the rolling moment in the direction of the spin
and/or increasing the anti-spin yawing moment. Of the two, the yawing moment is the more
important, but the rudder (the normal yaw control) is not the only control by which the pilot may
induce yaw.
99. The time-honoured sequence of control movements for spin recovery is idle power, the
application of full opposite rudder, control column forward until the spin stops, maintaining the
ailerons neutral. In certain aircraft the pilot’s handling notes may call for the use of aileron during
spin recovery.
FIGURE 4-24
Effect of Ice on the
Lift Curve
101. Formation of ice on the leading edge of the wing can cause significant changes to the local
aerofoil section, resulting in large changes in the local airflow and pressure gradients. Some forms of
ice have extremely rough surfaces, which cause high surface friction and a marked reduction in
boundary layer energy. The sum of these effects is a large increase in drag and a large decrease in the
maximum lift coefficient ( C Lmax ) . This, plus the added weight due to the ice, will mean that greater
power is required for a given speed and that the stalling speed is higher for a given weight.
102. The effect of a layer of frost on the upper surface of the wing (where it usually forms) is to
significantly increase the surface roughness of the wing, increasing drag due to skin friction and
reducing the boundary layer energy. Hence C Lmax is reduced, although not usually to the same
extent as with ice formation. Nevertheless, the reduction may well bring C Lmax down to a value
similar to that required for take-off.
103. The effect of ice and frost formations on take-off performance is of vital significance. The
stalling angle of attack may be reduced by up to 25% and the stalling speed may be increased by a
similar amount. To exacerbate the problem, the angle of attack sensor will continue to operate
normally so the stall will occur before the stall warning can activate - in other words, there will be no
stall warning. In addition, after recovery, speed must be increased to a value higher than normal and
this will involve additional height loss. At the very time when the pilot is obliged to operate the
aircraft close to the stalling speed, at high angles of attack, and close to the ground, ice or frost will
narrow the safety margins to a fatal degree. The moral is clear, NEVER attempt to take off with ice
or frost formation on the aircraft wing surfaces.
104. Finally, if ice forms on the wing surfaces it will almost certainly also form on the horizontal
stabiliser surfaces, modifying the aerodynamic effect of the stabiliser and increasing the possibility of
stabiliser stall. In this event the stall characteristics of the aeroplane may well be significantly altered,
producing abnormal behaviour at the stall.
105. Airframe ice formation must always be considered when flying through cloud or rain at a
temperature below 0°C. The temperature range favourable for ice accretion in thunderstorms is
from 0°C to -45°C, where water droplets can exist in a supercooled state. Below about -30°C
however, a large part of the free water content of the atmosphere normally consists of ice particles or
crystals and snowflakes and chances of severe icing at these low temperatures are greatly reduced.
QUESTIONS:
QUESTION 1.
QUESTION 2.
For a cambered aerofoil, at about what angle of attack will the best lift/drag ratio be produced?
QUESTION 3.
QUESTION 4.
QUESTION 5.
QUESTION 6.
QUESTION 7.
QUESTION 8.
QUESTION 9.
What will be the value of total drag when profile and induced are the same?
QUESTION 10.
QUESTION 11.
An aircraft at weight 8000kg stalls at 130kt. What will be the stalling speed at 6000kg?
QUESTION 12.
If the basic stalling speed of an aircraft is 90kt, what will be the stalling speed in a 50 degrees of bank
level turn?
QUESTION 13.
QUESTION 14.
Why do aeroplanes stall at a lower speed with power on than with power off?
QUESTION 15.
QUESTION 16.
QUESTION 17.
QUESTION 18.
Light aircraft are often fitted with a leading edge stall warning vane which deflects up just before the
stall. Why does it deflect up?
QUESTION 19.
QUESTION 20.
ANSWERS:
ANSWER 1.
ANSWER 2.
ANSWER 3.
Chap 3 page 6
ANSWER 4.
Chap 3 page 7
ANSWER 5.
Profile drag increases with increasing airspeed Chap 3 paragraph 23 figure 3-10.
ANSWER 6.
ANSWER 7.
ANSWER 8.
ANSWER 9.
ANSWER 10.
ANSWER 11.
ANSWER 12.
ANSWER 13.
ANSWER 14.
ANSWER 15.
Chap 4 page 17
ANSWER 16.
ANSWER 17.
The amount of advanced warning given before the stall occurs Chap 4 page 18
ANSWER 18.
ANSWER 19.
The speed range between the stall speed and limiting mach number Chap 4 page 121
ANSWER 20.
If wingdrop occurs, the downgoing wing suffers an increase in angle of attack, with further loss of lift
(roll), and an increase in drag (yaw)
Lift Augmentation
5 Lift Augmentation
1. High lift devices are fitted to aircraft in order to reduce the take-off and landing distances
required. They accomplish this by enabling the aircraft to achieve the required amount of lift at a
lower airspeed, thereby reducing rotation and take-off safety speeds, and also approach speeds. In
other words the co-efficient of lift is increased, thereby enabling a lower V in the lift formula, Lift =
CL½ρV²S. The types of high lift devices considered in this chapter are trailing edge flaps, leading
edge devices and boundary layer control devices.
2. In modern jet transport aircraft, with wing sections and planforms designed for high speed,
high altitude flight, lift augmentation is essential at the relatively low speeds of approach and
landing, take-off and climb.
5. The maximum lift coefficient that can be obtained with this type of flap is limited because the
increased camber encourages boundary later separation over the upper surface of the wing, which
reduces the stalling angle of attack (critical angle), when the flap is extended, to about 12°. This can
be a significant advantage during the landing approach, since less pitch up is required for a given
value of CL, improving visibility ahead.
6. The plain flap considerably increases drag when it is fully lowered, which is desirable during
approach and landing, but clearly not so during take-off and climb. This type of flap is best suited to
aircraft that operate in the lower speed range. If the use of flap is required during take-off, it is
usually limited to small deflections only.
FIGURE 5-1
Plain Flap
8. The split flap produces up to a 60% increase in lift, but at the expense of a large increase in
drag. Its use is therefore mainly limited to approach and landing. As with the plain flap it causes a
nose-down pitching moment, but the stalling angle of attack is only marginally reduced, to about
14º. The split flap was popular with aircraft designers at the time of the second world war and for a
short time afterwards. Its value was overtaken by the increase in aircraft size and the consequent
need for flaps suitable for use during take-off.
FIGURE 5-2
Split Flap
9. It is the loss of energy in the boundary layer that leads to separation when camber is increased
by the use of plain or split flaps. If the boundary layer energy can be restored it follows that
separation can be delayed and the wing, with flap extended, will be capable of maintaining lift at
much greater angles of attack. In other words, the stalling angle will be increased. One way of
achieving this is with the slotted flap.
FIGURE 5-3
Slotted Flap
11. Double (and even triple) slotted flaps may be used to permit slow, steep approaches at a
reasonable aircraft attitude. A double slotted flap is shown at Figure 5-4. The considerable
rearward movement of the centre of pressure when this type of flap is extended produces a marked
nose-down pitching moment. This is usually countered with associated leading edge devices. A 70%
increase of CLmax and a stalling angle of about 18º is achieved with a double-slotted trailing edge
flap.
FIGURE 5-4
Double Slotted
Flap
FIGURE 5-5
Fowler Flap
13. The effects of the foregoing types of trailing edge flap on the Lift Coefficient (CL) – Angle of
Attack (α) graph is shown at Figure 5-6.
FIGURE 5-6
Effect of Trailing
Edge Flaps on the
Lift Curve
14. Figure 5-7 shows the variation in Coefficient of Lift (CL) with increasing trailing edge flap
deflection.
FIGURE 5-7
Increment in
Coefficient of Lift
with Trailing Edge
Flap
It can be seen that the incremental increase in (CL) is initially linear with flap deflection but then the
increase reduces quite noticeably as the maximum flap angle is approached.
15. Figure 5-8 shows the variation in Coefficient of drag (CD) with increasing trailing edge flap
deflection.
FIGURE 5-8
Increment of
Coefficient of
Drag with Trailing
Edge Flap
Now we see that at the lower flap angles, the incremental increase in (CD) is small but it increases
markedly as the flap angle is further increased.
16. Figure 5-9 is a graph showing the influence of these trailing edge flaps on the relationship
between the Lift Coefficient (CL) and the Drag Coefficient (CD).
FIGURE 5-9
Effect of Trailing
Edge Flaps on C L -
CD Graph
Flap Asymmetry
17. Since the extension of trailing edge flaps produces such a marked increase in both lift and
drag it is clear that, should the flaps deploy asymmetrically, a very large rolling moment would result.
Under these circumstances the aeroplane would almost certainly become uncontrollable, because the
flaps retract fairly slowly and, in the meantime, the rolling moment provided by maximum aileron
deflection would most probably be insufficient to counter that of the asymmetric flaps. In view of
this, many modern aircraft incorporate comparative sensing in the flap control system, which will
not allow the flaps to deploy unless they are doing so symmetrically.
Take-Off
18. The use of trailing edge flaps for lift augmentation during take-off must by limited to the
setting recommended in the aircraft operating manual. This will invariably call for an extension
which is only a small proportion of the maximum flap extension available, and which gives the best
lift/drag ratio other than with a clean wing, reducing the stalling speed and hence take-off speeds.
This will, in turn, give the shortest possible take-off run. Deploying the flaps further than the
recommended setting will result in a longer take-off run (albeit possibly shorter than with no flap),
because of the large increase in drag. The drag penalty also means that use of flap for take-off will
reduce the climb gradient (angle of climb making obstacle clearance after take-off more difficult).
19. When flaps are lowered the lift is increased, but so too is the drag. At those angles of attack
which give the best lift drag ratio with a clean wing (flaps retracted) the drag increase when flaps are
lowered is proportionately greater than the lift increase. Hence, lowering flap worsens the lift/drag
ratio.
20. From Figure 5-7 and Figure 5-8, the rate of increase of coefficient of lift (CL) is greatest
during the first third of flap extension, whereas the rate of drag increase is least in that extension
range. In other words, at low flap angles the lift/drag ratio is still favourable, whereas at high angles
it is adverse.
Landing
21. For landing a large flap angle gives the required increase in lift, facilitating a lower nose
attitude for a low speed of approach and the high drag permits a steeper approach without speed
becoming excessive (the flap is also acting as an airbrake). This results in an improved view of the
runway at a reduced approach speed. The high drag also has the advantage that it gives deceleration
during the ‘float’ period between round out and touchdown and subsequent reduction in the landing
run.
24. To prevent leading edge separation, and to increase the stalling angle of attack, leading edge
lift augmentation devices are often used. They may simply increase the wing camber, as in the case of
Krueger flaps and leading edge droop, or they may ‘re-energise’ the boundary layer as in the case of
leading edge slats.
25. Leading edge devices tend to move the centre of pressure forward, consequently they tend to
counter the nose-down pitching moment of trailing-edge flaps, by producing a nose-up moment.
FIGURE 5-10
Krueger Flap
FIGURE 5-11
Leading Edge
Droop
FIGURE 5-12
Leading Edge Slat
29. It is normal for slats to extend along the entire length of the wing. The effect of the slat on the
co-efficient of lift is quite significant, being shown at Figure 5-13. Leading edge slats significantly
increase the stalling angle of attack, hence their use on high performance fighter aircraft and where
high incidence angles are required at low speeds (e.g. rotation for take-off). Slats may be deployed
manually, or automatically as pressure reduces behind the leading edge with increased angle of
attack.
FIGURE 5-13
Effect of Slats on
the Lift Curve
30. In addition to the effect of the slot (already described) the high camber which occurs when the
slat is extended is responsible for flattening the peak of the low-pressure envelope above the wing.
This is illustrated at Figure 5-14. Because the adverse pressure gradient behind the point of lowest
pressure is reduced with the slats open, separation of the smooth airflow from the upper surface of
the wing is delayed, almost to the trailing edge.
FIGURE 5-14
Effect of Slats on
the Pressure
Distribution
31. In some relatively low speed aircraft the slats are permanently in the open position. It may be
easier to think of this as a wing with slots cut through it just aft of the leading edge. With high-speed
aircraft the slats lie tucked up against the leading edge of the wing during cruise, and are extended by
the pilot for take-off and landing. Alternatively the position of the slats may be automatically
controlled, being adjusted as and when the trailing edge flap settings are altered. Finally, control of
the slats may be under the control of the pilot in normal circumstances, but may extend
automatically as the stall sensor senses a dangerously high angle of attack, which is approaching the
stalling angle of the clean wing. This latter method is often employed in aircraft designed to operate
at low altitude and to climb away steeply, such as crop-dusters.
Lift/Drag Ratio
32. With trailing edge flaps it was seen that the increase in lift achieved is always outweighed by
the increase in drag, hence any use of trailing edge flap reduces the lift/drag ratio as compared with
the clean wing. Leading edge devices, and especially leading edge slots, incur a relatively small drag
penalty for the increase in lift achieved and consequently the lift/drag ratio is improved at high
incidence over that of the clean wing and thus the gradient of the CL -CD curve does not reduce as
quickly as that for trailing edge devices.
Slat Asymmetry
33. With the type of slat that is selected for deployment by the pilot for take-off and landing it is
clear that any asymmetry of deployment would induce a large rolling moment, which would be
highly undesirable. In the case of this type of slat there is normally in-built control protection to
prevent asymmetric deployment of the slats.
34. The automatically-deploying slat however, extending automatically when the wing reaches a
high angle of attack, is capable of deploying asymmetrically if one wing’s incidence approaches
criticality.
36. We have seen how slots at the trailing and leading edges can achieve this to some extent, but
their effectiveness is largely dependent upon adequate airspeed and they invariably incur a drag
penalty. There are alternative methods of boundary layer control which have proved effective,
particularly on high-speed aircraft in which the weight and drag penalties of conventional flaps may
be unacceptable.
Control by Suction
37. By applying suction to a porous or slotted area of the upper surface of the wing, at the point
where the boundary layer is thickening due to the adverse pressure gradient, it is possible to draw off
the sub-layer, leaving a thinner boundary layer. This layer has greater velocity, since the greatly
retarded sub-layer has been removed. As a rule, distributing the suction over an area of porous
panels has proved more effective than the use of slotted panels. The source of the suction is usually
an engine-driven vacuum pump.
Control by Blowing
38. An alternative to adhesion of the boundary layer by suction is to eject high velocity air from
small jets in the same direction as the boundary layer flow. This has the effect of speeding up the
retarded sub-layer and re-energising the whole of the boundary layer. If this is combined with the use
of trailing edge flaps it is possible to obtain a very high maximum lift coefficient (CLmax). Figure 5-
15 shows a blown flap, which is capable of raising the CLmax from 1.5 for a plain aerofoil to about 5.
If this is applied to the lift formula it will be seen that the lift increase, all other conditions remaining
the same, is remarkable.
FIGURE 5-15
Blown Flap
39. In addition to boundary layer control by blowing over the trailing edge flaps, it can be
applied at the same time to the leading edge to increase lift even further. The practical limit for this
type of lift augmentation is set by the power requirements for blowing or suction. Theoretically, at
least, it is possible to reduce the landing speed of a high-speed swept wing aircraft by as much as
40% using these methods.
Vortex Generators
40. Vortices flowing chordwise across the upper wing surface can be induced either by small
metal vanes projecting normal to the wing surface, or by small jets of air blowing normal to the
surface. In either case the vortices carry the high velocity air near the upper part of the boundary
layer to the slow-moving air close to the wing surface. This transfers energy to the sub-layer,
maintaining boundary layer attachment towards the rear of the wing. There is a drag penalty
associated with the vane-type generators, but this can be kept to a minimum with careful design. An
advantage of the blown vortex generators is that they can be switched off when not required, so that
the drag penalty is only incurred during the lift-augmented phases of flight.
Drag Augmentation
41. Under certain flight conditions it is often desirable to be able to increase the drag of the
aircraft without, at the same time, increasing lift. The device designed to achieve this is the speed
brake, or flight spoiler. On high performance sailplanes this usually takes the form of slotted plates
which extend normal to the wing surfaces, creating drag to reduce the lift/drag ratio and steepen the
glide angle. Similar devices are often fitted to the fuselages of fast military jet aircraft to prevent
excessive speed in a dive and to control speed during manoeuvring.
42. There are also circumstances where it is an advantage to be able to destroy some of the lift
generated by the wings, either on both wings simultaneously or only on one wing at a time. This is
achieved by means of spoilers that normally lie flush with the wing upper surface, but are hinged at
the forward edge to deploy progressively, as shown at Figure 5-16.
FIGURE 5-16
Spoiler
Deployment
43. Spoilers of this type are fitted to most large transport aircraft and serve a variety of functions.
Flight Spoilers
44. In order to establish the aircraft in the descent spoilers on both wings are deployed
simultaneously and symmetrically. This destroys some of the lift being generated and creates drag,
decreasing the lift/ drag ratio. Thus the aircraft is able to commence the descent in a controlled
manner without the need to reduce speed for the deployment of flaps.
Ground Spoilers
45. After touchdown the aircraft is still moving at high speed and could conceivably become
airborne again in the event of a gust. To "kill" the lift and hold the aircraft on the ground additional
spoilers may be deployed.
Roll Spoilers
46. During the high-speed phases of flight the usefulness of ailerons for roll control is largely
offset by their tendency to induce wing twisting, especially in swept wing aircraft. Because of this,
spoilers are often used in conjunction with, or instead of, ailerons during high-speed flight. Under
these circumstances they are deployed asymmetrically and in proportion to the demands from the
pilot’s controls. The roll control system is necessarily complex in such aircraft, since it must be
capable of selecting, for example, spoilers only at high speed and ailerons only at intermediate
speeds. At low speed a combination of the two may be necessary to achieve adequate roll rates
during landing and take-off. This is known as spoiler-mixer control.
47. Figure 5-17 shows the positions of the wing-mounted spoilers on a Boeing 747. When flight
spoilers are selected as speedbrakes the two inboard spoilers on each wing are deployed together with
the inner two of the four outboard spoilers. Ground spoiler selection extends all the spoiler panels.
Roll control uses all four outboard spoiler panels and the outer of the two inboard panels on either
wing.
FIGURE 5-17
Spoilers -B747
FIGURE 5-18
Effect of Spoiler
Deployment on
the Lift Curve
Control
6 Control
Aircraft Axes and Planes of Rotation
1. Figure 6-1 illustrates the three axes of rotation about which an aircraft moves in flight. It will
be noted that they intersect at the aircraft centre of gravity (CG). This is always the case.
FIGURE 6-1
Axes of Rotation
2. The roll axis is the aircraft’s longitudinal axis running horizontally fore to aft. It is so called
because it is the axis about which the aircraft moves in roll, (left wing up, right wing down or vice
versa) either in response to the pilot's roll controls or due to an external disturbance. When the
aircraft moves about the roll axis it is rotating in the rolling plane, an imaginary vertical flat plane
aligned with the aircraft's lateral axis.
3. The pitch axis is the aircraft’s lateral axis running horizontally from side to side, intersecting
the roll axis at the aircraft centre of gravity. It is the axis about which the aircraft moves in pitch
(nose up or nose down) in response to the pilot's pitch controls or due to an external disturbance.
When the aircraft moves about the pitch axis it is moving in the pitching plane, an imaginary vertical
flat plane coincident with the aircraft’s longitudinal axis.
4. The yaw axis is the aircraft’s vertical, or normal, axis. It is so called because it is normal, or
perpendicular, to the two horizontal axes and intersects both at the aircraft centre of gravity. It is the
axis about which the aircraft moves in yaw in response to the pilot's yaw controls or due to an
external disturbance. When the aircraft moves about the yaw axis (nose left or right) it is moving in
the yawing plane, an imaginary horizontal flat plane coincident with the aircraft’s roll and pitch axes.
5. The purpose of the flight controls is to enable an aircraft to be rotated about its three axes.
The elevators achieve pitch control about the lateral axis. Control in roll about the longitudinal axis
is by means of the ailerons and control in yaw about the normal axis by means of the rudder. These
are known as the primary flight controls. They function by producing an aerodynamic force at a
point distant from the aircraft CG, so as to create a moment about the required axis.
6. The flight control produces an aerodynamic force by changing the camber of the lifting
surface to which it is attached, and/or by changing its angle of attack.
Camber Change
7. Controls usually take the form of hinged, flap type aerofoil sections mounted on the trailing
edges of the wing, the tailplane and the fin. When they are moved they alter the effective camber of
the section to which they are attached and therefore alter the amount of lift being generated. This
type of control is illustrated at Figure 6-2. Within reason, controls are positioned as far as possible
from the axis of rotation about which they are effective, so that they create the largest moment for
the least amount of force.
FIGURE 6-2
Flap Type Control
Surface
10. If aileron is applied to roll the aircraft the resulting bank angle causes it to sideslip. The
aerodynamic force acting behind the centre of gravity on the keel surfaces (fin, rudder, etc.) causes
the aircraft to yaw towards the lower wing. The secondary effect of aileron is, therefore, yaw.
Aerodynamic Balance
11. However, when a control surface is deflected the airflow acting over it will try to return the
control to the neutral position. The total force trying to return the control surface to the neutral
position is the product of the lift force on the control surface and the perpendicular distance of the
centre of pressure of the control surface to the hinge line. This is called the hinge moment and is
illustrated at Figure 6-3.
FIGURE 6-3
Hinge Moment
12. The magnitude of the lift force generated by any control surface will vary directly as the
square of the EAS. The pilot is required to provide the force to overcome the hinge moment and
deflect the control surface (in a manual system). At all but the lowest airspeeds he or she could do
with some form of assistance. This assistance is supplied in the form of control balance devices.
13. Control balancing is achieved either by reducing the hinge moment, or by setting up a force
that acts against the hinge moment.
15. With this type of balance, care must be taken in the design to ensure that the centre of
pressure is not too near the hinge line. When a control surface is operated its centre of pressure
moves forward. If the margin between the centre of pressure and the inset hinge is too small there is
a possibility that the CP will move forward of the inset hinge, reversing the direction of the hinge
moment and is known as overbalance. An inset hinge is illustrated at Figure 6-4.
FIGURE 6-4
Inset Hinge
Horn Balance
16. An example of a horn balance is shown at Figure 6-5. Although it is shown here on a rudder,
horn balances can equally well be used on ailerons or elevators. In this system a portion of the
control surface acts ahead of the hinge line, and therefore produces a moment in opposition to the
hinge moment.
FIGURE 6-5
Horn Balance
Internal Balance
17. A projection of the control surface in the form of a balance panel, often referred to as a
‘beak’, is connected by a flexible diaphragm within a sealed chamber to a fixed structure (eg. spar).
See Figure 6-6. Control surface movement produces a pressure differential between upper and lower
surfaces and these upper and lower surface pressure changes are fed to the chamber to provide a
partial balancing moment. Internal balance is therefore achieved with no increase in exterior drag.
FIGURE 6-6
Internal Balance
Balance Tab
18. Like the inset hinge and the horn balance the balance tab serves the purpose of reducing the
stick forces involved in moving a primary control surface, at a given airspeed. A balance tab is
shown at Figure 6-7. As the primary control surface moves one way, so the balance tab moves the
other. Since the tab is a considerable distance from the hinge line of the primary control, the moment
produced by it is large. The balance tab imposes a small penalty in terms of drag, and diminishes
slightly the effectiveness of the primary control surface to which it is fitted.
FIGURE 6-7
Balance Tab
Anti-balance Tab
19. In some aircraft, far from requiring assistance in moving a control surface against the
aerodynamic loads, the hinge moment is too small. This results in very low control column loads, a
lack of feel and the possibility of over-stressing the airframe due to excessive deflection of the control
surface. This often occurs because of the hinge being too close to the centre of pressure of the
control surface. In order to improve the situation an anti-balance tab is fitted which operates in the
same direction as the control surface. An anti-balance tab is illustrated at Figure 6-8.
FIGURE 6-8
Anti-Balance Tab
Spring Tab
20. With many aircraft aerodynamic balancing is not considered necessary at low airspeeds, but
is progressively required as airspeed increases, and with it the aerodynamic loads. The spring tab
system may then be fitted to deal with this situation. A spring balance tab is shown at Figure 6-9.
FIGURE 6-9
Spring Tab
21. The movement of the control column is transmitted to a lever pivoted on the main control
surface but not directly operating it. Operation of this surface is through springs, and with low
aerodynamic loads the movement of this pivot arm is transmitted to the main control surface
through the springs; consequently there is no alteration in the geometry between the primary control
surface and the balance tab. When the aerodynamic loads increase at high speed, in order to
transmit the control column movement via the pivot arm to the control surface, the spring becomes
compressed. This upsets the geometry of the system and brings into operation the balance tab on the
trailing edge, which moves in the opposite direction to the primary control surface, thus assisting the
pilot by reducing the stick forces involved.
Servo Tab
22. When manual controls are used to operate very large control surfaces the loads involved, even
with balance tab assistance, may be unacceptable. Under these circumstances servo tabs are used to
operate the control surfaces. A servo tab is a small aerofoil section, once again attached to the
trailing edge of the main control surface. The servo tab is operated directly by the control column,
with no direct connection between the control column and the main control surfaces. As with the
balance tab and the trim tab (described later), the servo tab moves in the opposite direction to the
primary control surface. A servo tab is illustrated at Figure 6-10.
FIGURE 6-10
Servo Tab
Trimming
23. There is sometimes confusion between balance tabs and trim tabs. Balance tabs serve to
aerodynamically balance the forces acting on a control surface in order to reduce the force required
to move it. Trim tabs serve to eliminate the force required to maintain a control surface at a
particular deflection.
24. For aircraft in flight to be in equilibrium the moments about each of the three axes of the
aircraft must balance. If they do not balance then an additional force must be supplied by deflection
of the controls to keep the aircraft in equilibrium. The physical effort necessary to maintain this
control surface deflection would place a great strain on the pilot, so to overcome this problem trim
tabs are provided.
25. Consider the situation that exists in the case of an aircraft that tends to continuously fly nose
up. In order to prevent this the elevator must be deflected downwards and maintained in this
position. In order to achieve this the trim tab attached to the trailing edge of the elevator is deflected
upwards as shown at Figure 6-11.
FIGURE 6-11
Trim Tab
26. The force required to maintain the elevator in the desired position is FP, and the work
involved is FP x distance DP (the length of the arm from elevator hinge line to the elevator centre of
pressure).
27. The action of the trim tab is to provide a much smaller force FT, but over a much larger arm
DT (from the elevator hinge line to the trimmer centre of pressure). The work involved in holding the
elevator out of the neutral position is thus done by the trim tab and requires no force from the pilot’s
controls.
28. The trim tab slightly reduces the effectiveness of the primary control surface, since the
primary control is already part way to full scale deflection with the aircraft in balanced flight. Also a
trim drag penalty is suffered, hence the introduction of the variable incidence tailplane for high-speed
flight, discussed later in this chapter.
29. Trim tabs may be controlled manually by trim wheels, often located on the centre console, or
by trimming electric motors, the control for which is normally located on the control column. As
with any control surface, the effect of any trimmer is proportional to the square of the airspeed.
Whilst small movements of the trim tab will suffice at high speed, significantly larger trim
movements are required at lower airspeeds, especially when significant changes of aircraft
configuration, such as the lowering of flaps and undercarriage, are involved. On many light aircraft
fixed trim tabs are fitted, which of course can only be adjusted on the ground.
Fixed Tabs
30. Fixed tabs are attached to the trailing edge of a control surface and can be set at a fixed angle
when the aircraft is on the ground. In flight, under conditions of no force on the pilot's controls the
position of the tab determines the trailing position of the primary control surface. Fixed tabs may be
as simple as a small rectangle of aluminium attached to the control surface and manually bent to the
required angle, which is found by trial and error. Some light aircraft still use a very early form of
fixed tab comprising strips of cord stuck to one side of the trailing edge of the primary surface.
Stabiliser Trim
31. As IAS is increased the angle of attack required to maintain level flight decreases and so the
elevator deflection necessary decreases. Hence less elevator trim is required for zero stick force as
indicated airspeed increases.
32. From this it follows that, at the low speed of take-off, significant elevator up deflection is
necessary to first initiate the take-off rotation and subsequently to maintain the necessary angle of
attack until airspeed increases. In order to keep the pilot’s control force required within acceptable
limits the stabiliser/elevator will need to be trimmed accordingly.
33. The further forward the CG of the aircraft the greater the elevator deflection necessary to
overcome the inherent longitudinal stability of the aircraft, the further aft the CG the less the
longitudinal stability and the more difficult the aircraft becomes to control in pitch. In the first case
the pilot may run out of elevator up movement and be unable to maintain pitch attitude, in the
second the aircraft may be too ‘tender’ and impossible to control in pitch.
34. It is clear that the CG position for take-off must be within well-defined limits and the
elevator/stabiliser trim setting must be pre-set so as to give minimum stick force at the deflection
required for take-off and initial climb. After all, the pilot has enough on his hands at this critical
stage of flight and does not want to be fiddling with the trim wheel.
35. Consequently the take-off longitudinal trim setting for a given CG position is usually stated in
the operating manual for the aircraft.
Pitch Control
36. Control of the aircraft about the lateral axis, or pitch control, is achieved with the elevator,
which is deflected by moving the control column (stick) forward or backward. Forward movement
of the stick deflects the elevator down, increasing the positive camber of the tailplane and creating an
upward aerodynamic force. This produces a moment about the lateral axis of the aircraft through
the CG, which pitches the nose down. In other words, the increase in tail lift coefficient as the
elevators are moved downwards results in a reduction in the pitching moment coefficient (ie. a nose
down pitching moment change) and hence a reduction in incidence. The aircraft lift coefficient is
correspondingly reduced. Rearward movement of the stick deflects the elevator up, with opposite
results.
37. The degree of control resulting from movement of the control column will depend upon the
area of the control surface, the amount by which it is deflected, the IAS of the aircraft and the
distance between the control surface and the aircraft CG (the moment arm).
38. The larger the surface area of the elevator the greater the aerodynamic force developed for a
given deflection angle at a given airspeed.
39. The further forward the CG the more stable the aircraft is longitudinally and the greater the
elevator deflection necessary to overcome that stability. As airspeed is reduced an increasing amount
of up elevator is needed to produce the same lift coefficient. If the CG were too far forward the pilot
would run out of available elevator deflection at the low speeds required during take-off and landing
approach.
40. Furthermore, as explained under stability in Chapter 8, the stabilising effect of the tailplane is
greater during manoeuvre than in steady level flight, ie. manoeuvre stability is greater than static
stability in level flight. Therefore, as in level flight, as the CG is moved forward, the greater the
elevator deflection required to overcome the increased stability, however for a given CG position, the
elevator deflection required is greater during manoeuvre than in steady level flight.
41. Consequently, the effectiveness of the elevators, or any other control surface for that matter, is
mainly dependent upon the extent of deflection and the airspeed. The higher the airspeed the less the
deflection necessary for a given attitude change. Control surface deflection required is inversely
proportional to the square of EAS.
42. In the case of the elevators the effect of downwashed airflow from the wings must also be
considered. As aircraft angle of attack changes so does the downwash angle. If the downwash
strikes the tailplane surface, as it does in most aircraft with a fuselage mounted tailplane, a change in
downwash angle alters the effective angle of attack of the tailplane and thus the lift it generates. This
in turn changes the pitching moment produced by the tailplane and will require elevator deflection to
maintain a given attitude.
43. There is an alternative type of flight control, in which the angle of attack, or incidence, of the
whole lifting surface is changed, with no change in camber. Figure 6-12 illustrates an example in
which the angle of attack of the tailplane is altered for trim changes, but which retains an elevator
(camber change) for pitch control. This is referred to as a variable incidence tailplane.
FIGURE 6-12
Variable Incidence
Tailplane
44. Figure 6-13 illustrates an example in which there is no elevator and where the tailplane
incidence is varied to provide pitch and trim control. This is known as a stabilator.
FIGURE 6-13
Stabilator
Yaw Control
45. Control about the normal, or yaw axis is achieved through movement of the rudder. The
rudder is hinged to the rear spar of the fin and is connected to the pilot’s rudder pedals. Pushing on
the right pedal deflects the rudder to the right, which alters the camber and effective angle of attack
of the fin such that an aerodynamic force to the left is produced. This creates a yawing moment
about the aircraft’s normal axis through the CG, which yaws the nose to the right. Pushing on the
left rudder pedal has the opposite effect.
46. The effectiveness of the rudder increases with increasing airspeed. At low speeds, such as
during the landing approach, a large deflection may be necessary to produce a given amount of yaw.
At higher speed only a small deflection is necessary to achieve the same effect.
47. In aircraft designed for high subsonic or transonic flight, but which must of course be capable
of controlled flight at low speeds, a pedal/rudder ratio changer is employed. As airspeed increases
the maximum obtainable rudder deflection angle is automatically decreased by the ratio changer.
The deflection decrease may be progressive, as illustrated in the graph at Figure 6-14, or it may be in
steps, associated with flap retraction for example.
FIGURE 6-14
Maximum Rudder
Deflection
Available Against
Speed
ff
48. In many aircraft, although by no means all, the ratio changer affects extent of rudder pedal
movement so that decreasing rudder deflection possible is matched by corresponding decreasing
pedal movement available.
49. In addition to the yawing moment due to rudder deflection there is also a yawing moment due
to engine thrust. The direct yawing moments are due to the force acting normal to the propeller
plane or the jet engine inlet. The further forward the engines are located the more destabilising the
yawing moments due to thrust.
50. The indirect yawing moments due to thrust arise from the propeller-induced velocities and
airflow at the vertical tail, which can produce significant directional trim changes. The indirect or
induced moments in jet-powered aircraft are negligible.
51. In multi-engine aircraft there is a strong yawing moment in the event of asymmetrical power
due to failure of one engine. The further the engines are located outboard of the CG the greater the
yawing moment developed. In propeller-powered aircraft there is little choice other than to mount
the engines on the wings, and the diameter of the propeller disc inevitably means that they must be
well clear of the fuselage.
52. The unbalanced thrust and drag in the event of asymmetrical power produces a yawing
moment that must be opposed by deflection of the rudder. The side force at the vertical tail must
produce a moment equal and opposite to the yawing moment due to the unbalanced thrust.
53. The yawing effect of asymmetric power will be greatest at low airspeed and high power, such
as would be the case in the event of loss of an engine shortly after take-off. The rudder must
therefore be capable of maintaining directional control at a predetermined minimum speed with a
critical engine out. Figure 6-15 shows in graphical form the determination of minimum directional
control speed.
FIGURE 6-15
Minimum
Directional
Control Speed
ff
54. The horizontal line on the graph shows the yawing moment coefficient (Cn) obtained from
maximum rudder deflection at any speed. The curved line shows the yawing moment coefficient due
to asymmetric thrust with one engine out and the remaining engine (or engines) at maximum power.
Clearly, when Cn due to asymmetric power exceeds Cn due to maximum rudder deflection, the
rudder is incapable of maintaining directional control. Minimum directional control speed is
therefore at the point where the two curves intersect.
55. The minimum control speed in the air, in the take-off configuration, is known as VMCA. It is
the minimum speed at which it is possible to suffer a critical engine failure and maintain control of
the aeroplane within defined limits.
56. The minimum control speed on the ground is known as VMCG. It is the minimum speed on
the ground at which it is possible to suffer a critical engine failure on take-off and maintain control
of the aeroplane with the use of primary aerodynamic controls alone within defined limits.
Roll Control
57. Control about the longitudinal, or roll axis of the aircraft is achieved in most aircraft through
the ailerons. The ailerons are hinged to the rear spar of the wing and are deflected by rotation of the
control wheel (mounted on the control column) or by sideways movement of the control column
(stick).
58. Suppose the control wheel is rotated to the right. The aileron on the right wing moves up to
create a downward force, whilst the aileron on the left wing moves down to create an upward force.
The result is a moment about the longitudinal axis, through the CG, rolling the aircraft to the right.
Rotating the control wheel to the left would produce the opposite effect.
59. As with the elevators and the rudder, the amount of deflection is directly proportional to the
amount of movement of the pilot’s control. The greater the aileron deflection the greater the rate of
roll that will result, the rate of roll being the time taken to accelerate through a given angle of roll.
The rolling motion is opposed by aerodynamic damping in roll, described in Chapter 8 on Stability,
so that a steady rate of roll is quickly established for any given aileron deflection.
60. Clearly the rate of roll achieved for any given aileron deflection will depend upon the surface
area of the ailerons, the airspeed and the distance from the ailerons to the centreline, or longitudinal
axis, of the aircraft. Aileron size is limited by a number of factors, the torsional stiffness of the wings
and the drag effects of the ailerons being the principal considerations. At low airspeeds then, it is
desirable for the ailerons to be mounted as far outboard as possible, to achieve the maximum rolling
moment.
61. However, at high airspeeds the aerodynamic force generated by aileron deflection can easily
be sufficient to cause the wing supporting it to twist. Remember, the force generated by the aileron
increases as the square of the EAS. The effect of wing twist is to minimise or even reverse the effect
of the ailerons and this is illustrated at Figure 6-16 and is fully explained under Flutter.
FIGURE 6-16
Effect of Wing
Twist
62. One way to overcome the problem of wing twist is to fit two sets of ailerons. Conventional
ailerons are fitted towards the outboard end of the trailing edge in the normal manner, for low speed
flight. A second set of smaller ailerons is fitted towards the inboard end of the wings, for high-speed
flight. At high speeds the outboard ailerons are locked into the neutral position and the inboard
ailerons are employed. The high speed offsets the small size of these surfaces in producing the
necessary control forces, whilst the thicker and more rigid wing structure at the inboard end resists
the aileron imposed forces which are trying to induce twist.
63. Spoilers may be used as well as, or instead of, ailerons during the high speed phases of the
flight. The effect of opening the spoiler (by a very small amount) is to cause a loss of lift, and
therefore roll in the direction of the raised spoiler. The spoiler does not introduce any significant
twisting force. Roll spoilers are fully covered under Drag Augmentation in Chapter 5.
Flutter
64. Figure 6-17 illustrates how a wing may twist in torsion and/or bend in flexure.
FIGURE 6-17
Wing Twist and
Bend
65. The torsional or elastic axis is the line about which the wing will twist if a force is applied to
the wing, other than on the line of the axis itself. A force applied on the line will not cause the wing
to twist. However, the wing may bend or flex under this force. Thus the torsional axis is an
important feature of the wing structure and is the axis about which the wing may twist in torsion or
bend in flexure.
66. Another form of vibration is caused by a control surface itself vibrating in the airflow, caused
by incorrect balancing or slackness in the control runs. Torsional and flexural vibrations are, in
themselves, fairly harmless and are usually damped out by the rigidity of the airframe structure.
However, when acted upon by an external force, the airflow, further reactions will occur which may
lead to structural failure.
67. Flutter may cause structural failure. It is a violent vibration caused by the interaction of the
mass of aerofoil surfaces and aerodynamic loads. Three forms of flutter affect the wing:
68. Torsional Flexural Flutter occurs as a result of the wing flexing and bending when
aerodynamic loads are applied. Figure 6-18 shows the sequence of events.
FIGURE 6-18
Torsional Flexural
Flutter
(a) The wing is in steady horizontal flight with the torsional axis ahead of the centre of
gravity. Lift L is balanced by the reaction R caused by the bending of the wing due to
the weight of the aeroplane.
(c) The wing reaches its aeroelastic bending limit due to inherent stiffness and this brings
the torsional axis to rest, but inertia causes the C of G to travel further, decreasing
incidence. L is now less than R and the wing starts to descend.
(d) The wing stops moving down when it again reaches its aerolastic bending limit,
bringing the torsional axis to rest, but inertia causes the C of G to travel further,
increasing the incidence. L is now greater than R and the cycle repeats.
FIGURE 6-19
Torsional Flexural
Flutter Cycle
69. Torsional flexural flutter can be prevented in the design, either by ensuring that the wing is
sufficiently stiff so that the critical flutter speed is far in excess of the maximum speed limit, or by
ensuring that the centre of gravity of the wing is on, or ahead of, the torsional axis.
70. Torsional Aileron Flutter is caused by the wing twisting because of aerodynamic loads
produced by aileron deflection. The sequence is shown at Figure 6-20, which shows half a cycle.
FIGURE 6-20
Torsional Aileron
Flutter
(a) The aileron is deflected down, with a resulting increased lift force on the aileron hinge.
(b) The wing twists about the torsional axis. The trailing edge rises, taking the aileron
with it. Because the aileron C of G is behind the hinge, the aileron lags behind this
upward movement, generating an even greater upwards force from the aileron thus
increasing the twisting moment.
(c) The torsional reaction of the wing arrests the twisting motion but the aerodynamic
loads on the aileron, together with its upward momentum and the stretch of the
control runs, cause it to continue upwards, now placing a downwards load on the
wing trailing edge.
(d) The energy stored in the twisted wing and the aileron aerodynamic load cause the
wing to twist in the opposite direction, and the cycle is repeated.
71. This type of flutter can be prevented either by mass-balancing the ailerons (see next section),
or by making the controls irreversible. Aircraft with fully powered controls and no manual reversion
do not require mass-balancing.
72. Flexural Aileron Flutter is similar to the previous phenomenon but is caused by the movement
of the aileron lagging behind wing upwards and downwards movement as it flexes, This tends to
amplify the oscillation. The sequence is shown at Figure 6-21.
FIGURE 6-21
Flexural Aileron
Flutter
FIGURE 6-22
Mass Balancing
73. This type of flutter can be prevented by mass-balancing of the aileron as shown in
Figure 6-22. The positioning of the weight is important. The nearer the wingtip the smaller is the
weight required. Sometimes the weight is distributed along the whole length of the aileron in the
form of a leading-edge spar, thus improving the stiffness of the aileron and preventing a concentrated
weight starting torsional vibration in the aileron itself.
74. It should be appreciated that tail surfaces may also experience flutter and, unless fully-
powered, will also require to be mass-balanced. Tailplanes and elevators tend to be stronger in
torsion than wings because of their smaller dimensions, but large fins as found on large transport
aeroplanes may be less torsionally strong than the remainder of the empennage.
Divergence
75. Lack of torsional rigidity in a wing can, in extreme cases, cause divergence, as shown at
Figure 6-23.
FIGURE 6-23
Divergence
76. If the incidence of a wing is increased momentarily by a disturbance, lift will increase, moving
the centre of pressure forward. If the torsional axis is behind the centre of pressure the lift increase
and forward movement will increase the moment which is twisting the wing. Conversely, if the
disturbance decrease the incidence, the reduction in lift and aft movement of the centre of pressure
will further reduce the incidence. In both cases the twisting action is resisted by the torsional stiffness
of the wing. However, because lift increases with the square of the speed and torsional rigidity
remains constant, there is a critical speed (the divergence speed), beyond which the aerodynamic
moment will overcome the resistance of the wings torsional rigidity. In such a situation the wing will
twist until structural failure occurs. This may be avoided by making the wing sufficiently stiff in
torsion so that the divergence speed is well beyond the aircraft speed limit, or by designing the wing
such that its torsional axis is ahead of the aerodynamic axis, thus preventing divergence at any speed.
Adverse Yaw
77. When an aircraft is rolled the downgoing wing experiences an increased effective angle of
attack, whilst the upgoing wing experiences a decreased angle of attack. The inclination of the lift
vector consequently produces a forward component on the downgoing wing and a rearward
component on the upgoing one. Thus there are yaw moments acting about the normal axis in
opposition to the yaw required from the roll direction. This is known as adverse yaw.
78. In order to achieve a rate of roll one of the ailerons must be lowered and the other one raised.
The induced drag created by the lowered aileron is much greater than that caused by the raised one
which produces a yawing moment in the opposite direction to the intended turn. This effect is called
adverse aileron yaw, and is most marked when aileron deflections are large, which usually occurs at
low airspeeds.
79. There are a number of devices designed to minimise or overcome adverse aileron yaw.
Frise Ailerons
80. With this type of aileron it is arranged that the forward part of the up-going aileron will
protrude into the airflow below the wing as shown at Figure 6-24. In this way drag is generated at
the wing which is on the inside of the turn to match the drag of the downgoing aileron on the outside
of the turn, thus preventing yaw. It is not the most efficient solution however, since it adds profile
drag to the upgoing aileron to balance the induced drag of the downgoing aileron, rather than
reducing the drag of the downgoing aileron.
FIGURE 6-24
Frise Ailerons
FIGURE 6-25
Differential
Ailerons
Rudder/Aileron Coupling
82. In some aircraft the rudder is coupled to the ailerons by gearing or spring so that deflection of
the ailerons also moves the rudder a proportionate amount to oppose adverse yaw.
Roll Spoilers
83. The use of spoilers rather than ailerons in high-speed flight has already been mentioned.
These devices are also very useful in overcoming the problem of adverse yaw at low speeds, when its
effects are most noticeable and hazardous. The spoilers operate in conjunction with the ailerons.
The wing on which the aileron goes down experiences an increase of lift and on this wing the spoiler
remains retracted flush with the wing surface. The wing on which the aileron goes up suffers a loss
of lift and an increase in drag by the extension of the spoiler, so this wing drops in the required
direction of roll and the drag induces yaw in the required direction also.
84. Another advantage of spoilers is that the control forces needed to operate them are relatively
low.
Slot/Aileron Coupling
85. A method that has been used with great success on light aircraft required to execute sharp
manoeuvres at low airspeed and altitude is to place slots that open automatically, or in conjunction
with aileron down deflection, at the leading edge of the wing immediately ahead of the ailerons. This
system is illustrated at Figure 6-26.
FIGURE 6-26
Slot Aileron
Coupling
Powered Controls
87. The force needed to move the control surfaces of a large aircraft flying at high speeds makes it
virtually impossible for satisfactory control to be exercised by manual controls. It is therefore
necessary that the primary control surfaces be power operated.
88. Powered controls may be divided into two categories, power-assisted controls and fully
power operated controls.
91. Safeguards against faults or power failure may be provided by manual reversion, or by more
than one system, each with its individual hydraulic circuit. Thus conventional trailing edge tabs will
not be included and trim would be obtained by altering the zero positions of the artificial feel
mechanism. Occasionally, where necessary, balance tabs are fitted for the maintenance of servo and
hinge loads. An example of a power operated control system is shown at Figure 6-27.
FIGURE 6-27
Powered Flying
Control System
92. Power operated controls are irreversible, which means that there is no feedback of
aerodynamic forces from the control surface. Consequently, the pilot has no feel through the
controls for the aerodynamic loading on the control surfaces.
93. Feel is provided by artificial methods and, in fact, the artificial feel rarely has any direct
relationship to the forces working on the control surface. Feel can be provided by a spring that
exerts a constant load for a given control position, so that the more the control is moved the greater
the spring force to be overcome. The disadvantage of this system is that the resistance to control
movement is the same irrespective of airspeed. A proportionate force at low airspeed would be
inadequate at high speed, alternatively a proportionate force at high airspeed would be too great at
low speed.
94. A much more satisfactory arrangement is to provide loading which varies in direct
relationship to airspeed. This loading is a force proportional to dynamic pressure (q). The
arrangement is therefore commonly referred to as q feel. Pitot and static pressure is sensed and
applied to the pilot’s controls to produce a force resisting movement proportional to airspeed and
therefore representative of the force the pilot would feel with manual controls. In its simplest form a
q feel system comprises a large piston with pitot pressure applied to one side and static pressure to
the other. The overall force acting on the piston is thus due to dynamic pressure. The piston is
connected to the pilot’s controls as shown at Figure 6-28.
FIGURE 6-28
Simple ‘q’ Feel
95. The bulkiness of the simple ‘q’ feel system can be overcome by the utilisation of a
hydraulically enhanced system in which the pitot and static pressures are fed to either side of a
diaghragm attached to a hydraulic servo-valve. The servo-valve provides a metered hydraulic
pressure, which is an amplified value of dynamic pressure, to a small jack which opposes control
column movement. An example of a hydraulic ‘q’ feel system is shown at Figure 6-29.
FIGURE 6-29
Hydraulic ‘q’ Feel
Fly-By-Wire
96. In many present-generation aircraft signals from the pilot's primary controls are transmitted
electrically to actuators which move the control surfaces. This is known as fly-by-wire. The system
lends itself to the incorporation of sophisticated electronic processing which alters the response to
control inputs by the pilots to avoid stalling, over-rapid or excess control surface movement, or
unstable flight regimes. Fly-by-wire not only has the capability to improve aircraft performance,
efficiency and safety, it can also incorporate co-ordination of control surface movements too
complex for a pilot to achieve unaided.
Forces in Flight
7 Forces in Flight
Forces in Level Flight
1. The four forces acting on an aircraft in straight and level flight are lift, weight, thrust and
drag. Lift acts through the centre of pressure and weight through the centre of gravity. For
simplicity, thrust and drag forces are considered as acting parallel to the longitudinal axis, and their
displacement from this axis depends on the design of the aircraft, high wing or low wing, the position
of the engine(s), and so on.
2. Providing that the centre of gravity and the centre of pressure are not coincident a force
couple will be set up by the lift and the weight forces, and this will result in a pitching moment, as
shown at Figure 7-1.
FIGURE 7-1
Lift/Weight
Pitching Moment
3. The magnitude of the pitching moment will depend on the magnitude of lift and weight
forces, but also on the distance between the centre of gravity and the centre of pressure.
4. The position of the CG will depend on the way in which the aircraft is loaded, and on the way
in which fuel is transferred/consumed in flight. The position of the centre of pressure depends on the
angle of attack, with the CP moving slowly forward as the angle increases, and then rapidly
backwards at the stalling angle.
5. The couple between the thrust and drag forces may compliment the lift/weight pitching
moment as shown at Figure 7-2, or oppose it as shown at Figure 7-3.
FIGURE 7-2
Lift/Weight and
Thrust/Drag
Pitching Moments
- Complimentary
FIGURE 7-3
Lift/Weight and
Thrust/Drag
Pitching Moments
- In Opposition
6. With the couples arranged as shown at Figure 7-2 it would obviously be necessary for the
tailplane to produce negative lift, in order to maintain level flight.
7. A change in any one of the forces will disturb the trim of the aircraft, causing it to pitch either
nose up or nose down. For example, if the thrust force is reduced by throttling back the engine, it
can be seen from Figure 7-3 that the lift/weight couple is now greater than that of the thrust/drag
causing the aircraft to pitch nose down. To maintain balanced level flight therefore, the elevators
would have to be raised to produce a down-load at the tailplane.
8. One important consideration in respect of the lift/weight force couple is the way in which the
aircraft behaves in the event that the thrust/drag couple is destroyed, in other words during engine
failure with a single engine aircraft. With the centre of gravity forward of the centre of pressure, the
natural tendency will be for the nose to drop when the thrust/drag couple is removed as the engine
fails, and this is desirable.
10. During the climb the lift continues to act at right angles to the flight path and the weight
vertically downwards, however the two are now no longer directly opposed, see Figure 7-4. The
weight must now be resolved into two components, that which is supported by lift, and that acting in
the opposite direction to the flight path, i.e. in the same direction as drag. Therefore, for
equilibrium, resolving the forces along the flight path,
T = D + W Sin γ=
and resolving at right angles to the flight path,
L = W cos γ
11. Consequently the lift required for the same weighted aircraft is less than was needed for level
flight, since the lift supports only that component of the weight given by W Cos γ, where γ is the
angle of climb. However, the thrust available now has to match not only the drag, but also the
component of the weight given by W Sin γ at Figure 7-4.
FIGURE 7-4
Forces in a Steady
Climb
Thrust – Drag
Sinγ = ----------------------------------
Weight
13. Referring now to the triangle of forces diagram at the bottom of Figure 7-4:
Excess Power
Therefore: Rate of Climb = -----------------------------------
Weight
14. This proves that, for a specified weight and at one optimum TAS the greater the margin
between power available and power required the greater would be the rate of climb. The best rate of
climb will be achieved when the power margin is greatest.
15. From the above equation it can be seen that the rate of climb varies inversely with aircraft
weight. The best rate of climb for a given power margin will be less if aircraft weight is increased,
and vice versa. Reference to the triangle of forces diagram at Figure 7-4 will show that a reduction in
best rate of climb involves an increase in TAS for best rate of climb.
16. Similarly as altitude is increased the IAS needed to achieve the optimum TAS will decrease,
due to decreasing air density.
17. The graph at Figure 7-5 shows the curves of power available against power required for a
piston-engined aircraft.
FIGURE 7-5
Best Rate of Climb
- Piston Aircraft
18. The power available curve shows up the inefficiencies of the propeller at low airspeed
(ineffective angle of attack) and at high airspeed (compressibility losses and high drag losses).
19. The power required curve shows a disproportionate requirement for power at low speeds in
order to overcome the high induced drag factors.
20. Clearly, power available must exceed power required in order to maintain a steady climb.
21. The graph at Figure 7-6 shows the curves of power available against power required for a jet
engined aircraft. The big difference here is that the power available curve is more or less constant,
since the thrust available from a jet engine at a given altitude remains fairly constant, regardless of
speed.
FIGURE 7-6
Best Rate of Climb
- Jet Aircraft
22. The effect of altitude on the best rate of climb speed is shown for a piston-engined aircraft at
Figure 7-7 and for a jet engined aircraft at Figure 7-8. In both cases the power available diminishes
with increasing altitude (the powerplants become less efficient in low-density air). Equally the power
required increases with altitude, and so eventually an altitude will be attained where any further
climb is impossible. This is the absolute ceiling. The service ceiling is the altitude at which the rate
of climb has dropped to 100 feet per minute in a piston-engined aircraft and 500 feet per minute in a
gas turbine powered aircraft.
FIGURE 7-7
Effect of Altitude
on Best Rate of
Climb - Piston
Aircraft
FIGURE 7-8
Effect of Altitude
on Best Rate of
Climb - Jet Aircraft
23. The best angle of climb will be achieved at a speed where the margin between thrust and drag
is the greatest. Reference to the diagram at Figure 7-4 will establish that the climbing angle (γ) will
be greatest when the margin between thrust and drag is greatest, since:
Thrust – Drag
Sinγ = ----------------------------------
Weight
FIGURE 7-9
Forces in a Steady
Descent
Assuming that thrust acts along the flight path, resolving along the flight path,
T + W Sin θ = D or T = D - W sin θ
25. So, drag is balanced by thrust and the component of weight acting along the flight path and is
therefore, greater than thrust. Now, resolving at right angles to the flight path,
L = W cos θ
and consequently, as in climbing flight, the lift required for the same weighted aircraft is less than
was needed for level flight since in the descent lift supports only that component of the weight acting
perpendicular to the flight path given by W cos θ.
Emergency Descent
26. The situation most likely requiring a rapid descent from altitude is a rapid loss of cabin
pressurisation. If this were to be caused only by a failure of the pressurisation system itself, without
being caused by any structural failure (such as window failure or pressure bulkhead failure), then the
aircraft may be descended at the maximum possible rate.
FIGURE 7-10
Rate of Descent
(D – T)
Sin θ=== ------------------
W
therefore, rate of descent will be maximum when
V(D – T )
----------------------- =is maximum,
W
ie. increase airspeed, increase drag, reduce thrust.
27. This will be acheived with idle thrust, maximum speedbrake, and at limit speed values.
Whilst this is the fastest method of losing height, it must be accomplished with care because of the
high speeds involved. If there has been some form of structural failure, then it is not advisable to use
this method since the high values of dynamic pressure involved may cause further failure, perhaps
catastrophically. Therefore it will be necessary to descend at a lower speed. Whilst this has the
disadvantage of incresaing the time required to get down, it is more easy to fly since the aeroplane
will not be at limiting speeds, although if flap is used to increase drag then flap limit speeds must be
observed.
FIGURE 7-11
Forces in a Steady
Glide
29. To overcome the drag and maintain speed in the glide, the source of energy is no longer the
engine but the aircraft’s potential energy (ie. altitude).
L = W cos θ=
D = W sin θ.
31. From Figure 7-12, triangles A formed by lift, drag and total reaction and B, formed by range,
height and glidepath are geometrically similar and for maximum distance (range) gliding angle (θ)
must be minimum,
33. The gliding range can be calculated by reference once more to Figure 7-12 from the two
similar triangles A and B,
Range Lift
------------------ = ------------- .
Height Drag
FIGURE 7-12
Forces in a Steady
Glide
Therefore,
L
Range = ---- x Height.
D
34. On the other hand, for minimum rate of descent, ie. maximum endurance, we know that V
Sin θ= must be a minimum. But, from paragraph 28,
D
D = W Sin θ,=========therefore, Sin θ=== ----- .
W
DV
Therefore, V Sin θ=== ---------- where (D x V) is power required.
W
Thus, maximum gliding endurance (for a given weight) is achieved at the speed where power
required is a minimum as shown at Figure 7-13.
FIGURE 7-13
Best Glide
Endurance Speed
Effect of Wind
35. When gliding for maximum endurance, wind will have no effect since it is only the horizontal
velocity and hence distance travelled which is affected.
36. The glide or descent range is defined as the horizontal distance travelled during the descent.
The best glide distance through the air is achieved by flying the aircraft for minimum drag. In still air
conditions this will achieve the greatest ground distance covered during the descent. The true air
speed for minimum drag is found from the graph of power required against airspeed by extending a
line from the point of origin of the graph to make a tangent with the power required curve. The TAS
perpendicularly beneath the point of intersection is the best TAS for range in still air. This is
illustrated at Figure 7-14.
37. When descending against a headwind the ground distance covered per unit time is less and so,
to increase the ground distance covered the TAS must be increased. Similarly a tailwind would
increase the ground distance covered or, alternatively, the descent speed would have to be reduced to
achieve a given glide range. The effect is also illustrated at Figure 7-14.
FIGURE 7-14
Effect of Wind
Component on
Maximum Range
Glide Speed
Effect of Weight
38. Providing that the aircraft is flown at the speed that gives the best lift/drag ratio, the weight of
the aircraft will not affect the glide range. This is shown at Figure 7-15, which illustrates that the
increased weight will cause the aircraft to move faster down the descent path, which will increase the
lift without a requirement to change the angle of attack.
39. However since a heavier aircraft will glide at a higher speed, it will cover the same distance as
a lighter aircraft in a shorter time and its endurance is therefore, less. Consequently, glide endurance
reduces with increasing weight.
FIGURE 7-15
Effect of Weight
on Glide
Endurance
FIGURE 7-16
Lift in a Turn
41. The horizontal component of the total lift vector is used to provide the centripetal force that
causes the aircraft to follow a curved path.
42. The additional lift required must be generated by increasing the angle of attack and this will
result in increased induced drag and a subsequent decrease in airspeed, unless engine power is
increased.
43. The increase in lift required in a turn may be considered as compensating for the apparent
increase in aircraft weight during the turn.
44. The amount by which the weight apparently increases is known as the load factor (n) and is
given by the formula;
Lift
n = -------------------
Weight
45. From Figure 7-17 it can be determined that the bank angle θ is a trigonometrical function of
the weight and lift vectors such that:
Weight
Cosθ = -------------------
Lift
1
n = -------------
Cosθ
47. A turn employing an angle of bank of 60° will therefore produce a load factor of:
1 1
n = ------------------- = ------- = 2
Cos60° 0.5
48. The forces acting on an aircraft in a steady co-ordinated turn are shown in Figure 7-17. The
vertical component of the lift supports the weight and the horizontal component is used to provide
the centripetal force that causes the aircraft to follow a curved path.
FIGURE 7-17
Forces in a Steady
Co-ordinated Turn
49. When any body is turning about a fixed point at constant speed (V) there is an acceleration
towards the centre of the turning circle of:
V2
------ where r is the radius of the turning circle
r
50. If the body has a weight (W), then the centripetal force required to maintain the body at a
given turning radius r is given as:
WV 2
Centripetal Force = ------------
gr
WV 2
L Sin θ = ------------
gr
V2
therefore Tan θ = ------
gr
and so the angle of bank θ is dependent upon TAS (V) and radius of turn (r) and independent of
aircraft weight (W).
V2
r = ----------------
gTanθ
Thus the radius of turn can be calculated given aircraft speed and angle of bank. (Assuming a
constant value of ‘g’ or 9.81 m/s)
52. For example, if an aircraft enters a 30° bank co-ordinated turn at a TAS of 180kt, the turn
radius will be: (assuming 1kt = 1.51 m/s i.e. 180kt = 92.7 m/s.
V2
r = ----------------
gTanθ
2
( 92.7 )
r = ------------------------------------
9.81 × Tan 30°
8593.29
= ------------------------------
9.81 × 0.577
= 1518m
53. Thus the turn radius for any given combination of speed and bank angle can be found. To
reduce the turn radius the bank angle must be increased. However, the vertical component of lift
must be maintained which means increasing the angle of attack to increase lift and therefore the load
factor increases. Furthermore, to avoid stalling the speed must be increased as bank angle is
increased. The minimum turn radius for any aircraft is determined by the engine power available to
maintain speed above Vm, the manoeuvring stall speed, and the limiting load factor n.
54. In order to avoid overstressing the aircraft by "pulling too many g’s" (exceeding the limiting
load factor) in the turn the pilot needs a single parameter by which to judge the angular velocity of
the aircraft.
55. The angular velocity is the rate at which the aircraft is turning and is referred to as the rate of
turn or rate of change of heading. It is the ratio of TAS to turn radius and is usually measured in
radians per second
V
i.e. Rate of Turn = ---- radians per second
R
V2
but r = -------------------
g Tan θ
V
therefore Rate of Turn = ---------------------------
2
V ⁄ gTanθ
gTanθ
and, Rate of Turn = ----------------
V
56. Thus it is a function of the two main variables, bank angle and TAS and is more conveniently
measured in degrees per second.
57. For passenger transport aircraft the maximum rate of turn is usually limited to 3° per second,
which is known as a Rate One turn. The pilot is thus able to maintain an indicated rate one turn by
adjusting the bank angle to suit the airspeed. As a result the load on the aircraft and the g
acceleration felt by the passengers will always be well within acceptable limits.
58. In a steady co-ordinated (balanced) turn, the only acceleration on the aircraft is along the
normal axis. In an unco-ordinated turn, however, there is a lateral acceleration acting towards the
centre of the turn, slip, or away from the centre of the turn, skid.
59. Where the acceleration is to the inside of the turn, the aircraft is slipping and has too much
bank for the speed and radius. Where the acceleration is to the outside of the turn, the aircraft is
skidding and has insufficient bank for the speed and radius.
60. Therefore, an aircraft which is overbanked will ‘slip-into’ the turn and this can be corrected
by increasing the speed or reducing the angle of bank whilst applying more rudder.
61. On the other hand, an underbanked aircraft will ‘skid-out’ of the turn and this can be
corrected by reducing speed or increasing the bank angle whilst applying less rudder.
Asymmetric Thrust
62. Loss of a power plant on a multi-engine aeroplane produces a yawing moment about the
normal axis due to the greater thrust on one side of the normal axis and the greater drag on the other.
This was discussed in Chapter 6, on Control. The yawing moment due to asymmetric thrust must be
countered by the use of rudder deflection to provide an equal and opposite yawing moment.
63. The side force produced by rudder deflection will depend upon the dynamic pressure, which
of course depends upon the indicated airspeed. The lowest IAS at which the rudder at full deflection
provides just sufficient force to create a yawing moment balancing the moment due to asymmetric
thrust is known as the minimum directional control speed. Minimum directional control speed is
usually no greater than 1.2 times the stall speed at take-off configuration and minimum all-up
weight.
64. Figure 7-18 shows the force balance when the rudder is deflected towards the operational
engine on a twin engine aircraft with one engine inoperative. Deflection of the rudder gives camber
to the vertical fin, creating sideways lift. The distance between the CP of the fin and the aircraft CG
is the moment arm of the fin force. The distance between the thrust line of the operating engine and
the CG is the asymmetric thrust moment arm.
FIGURE 7-18
Yawing Moments
Under
Asymmetric
Power
65. The asymmetric thrust moment arm will be greatest in the event of failure of the most
outboard engine on the wing. However, with propeller powered aircraft, where the propeller
rotation is in the same direction for each engine (ie. without counter rotating propellers) failure of
one engine will be more critical, due to asymmetric blade effect (see Chapter 12).
66. For example, for a right hand tractor propeller, asymmetric blade effect causes the thrust line
to be displaced to the right as in Figure 7-19 and the moment arm of the right engine is greater than
that of the left.
FIGURE 7-19
Asymmetric Blade
Effect
67. Consequently, failure of the left engine will result in a greater out of balance yaw and roll
moment from the right engine. The left engine is referred to as the critical engine and is used when
establishing minimum control speeds.
68. Due to the side force on the vertical tail surface it is necessary to maintain a slight angle of
bank towards the operative engine. This raises the wing on the inoperative side and provides a
horizontal component of lift to balance the side force of the tail.
69. It is important in asymmetric power situations to avoid over-banking the aircraft. It will be
recalled that during a banked turn the load factor, and therefore the stalling speed, increases. Of
even greater importance when flying with one engine inoperative, the induced drag increases and
therefore speed decreases. Loss of speed is highly undesirable bearing in mind the need to stay above
minimum directional control speed. Up to 15° of bank the increase in stall speed and induced drag is
of no great significance, but beyond that bank angle both increase dramatically.
70. With the rudder at or close to maximum deflection to maintain directional control, the fin is
inevitably close to its stalling angle of attack. Any loss of airspeed or tendency to sideslip under these
circumstances is very liable to result in fin stall and complete loss of directional control. Since
excessive use of bank angle renders sideslip more probable and is liable to cause speed loss due to
greater induced drag it follows that it can lead to fin stall.
71. In addition to the asymmetric control effects with one engine inoperative on a multi engine
aeroplane the effect of loss of thrust must be considered. Besides the reduction in level flight speed
due to reduced thrust available, there is less excess thrust for acceleration or climbing. Figure 7-20
shows in graphical form the reduction in excess thrust available when only half the engines are
operative. Clearly the climb performance of the aeroplane is greatly diminished under these
circumstances. In conditions of high all-up weight, high altitude or high ambient temperature the
reduction in excess power may mean that the aircraft not only has insufficient power to climb, but
possibly insufficient to maintain height.
FIGURE 7-20
Reduction in
Excess Thrust
Available Under
Asymmetric
Power
72. When conditions are critical, as in the above paragraph, any increase in total drag whether
due to excessive bank angle during a co-ordinated turn or to the extension of flaps or landing gear
may create a thrust deficiency and make it impossible to maintain height. Figure 7-21 illustrates in
graphical form the differences in thrust required in turning and level flight and clean versus landing
configurations, against thrust available with one engine inoperative.
FIGURE 7-21
Thrust Defficiency
Under
Asymmetric
Power and
Different
Configurations
73. Under asymmetrical power conditions the use of ailerons must be exercised with care since
the secondary effect of roll is yaw. Yaw towards the operative engine may lead to sideslip and/or fin
stall, yaw towards the dead engine may lead to loss of directional control.
74. Besides the yawing moments due to asymmetric thrust there are also roll moments, especially
on propeller powered aircraft. With a twin engine propeller aircraft the torque reaction to the
operative propeller is not balanced by the feathered propeller on the inoperative engine and this
creates a rolling moment about the longitudinal axis. The direction of roll will depend upon the
direction of rotation of the operative propeller.
75. When trailing edge wing flaps are extended the propeller wash adds to the lift force generated
by them. Clearly, with no wash from the feathered propeller there is greater lift on the powered side,
creating a rolling moment towards the dead engine.
76. Sideslip will also induce a rolling moment because of the unbalance of lift on the wings, the
greater the sideslip angle the greater the roll moment resulting.
77. Furthermore, with an increase in weight, more power will be required to overcome the
increased drag and consequently there will be an increase in the yawing moment, following engine
failure, at this increased weight.
78. This increased yawing moment results in greater sideslip towards the live engine and a
subsequent increase in the resulting rolling moment to the dead engine. This effect is more
pronounced with dihedral and sweepback.
79. The minimum control speeds when operating in an asymmetric power situation are defined
below.
80. VMCA is the minimum control speed in the air in the take-off configuration. It is the
minimum speed at which it is possible to suffer a critical engine failure and maintain control of the
aeroplane within defined limits.
81. VMCG is the minimum control speed on the ground. It is the minimum speed at which it is
possible to suffer a critical engine failure on take-off and maintain control of the aeroplane with the
use of primary aerodynamic controls alone, within defined limits.
82. VMCL is the minimum control speed in the air in an approach or landing configuration. It is
the minimum speed at which it is possible, with a critical engine inoperative, to maintain control of
the aeroplane within defined limits while applying maximum variations of power.
QUESTIONS:
QUESTION 1.
QUESTION 2.
QUESTION 3.
QUESTION 4.
QUESTION 5.
QUESTION 6.
What is the purpose of control surface aerodynamic balancing, and how is it achieved?
QUESTION 7.
All balance tabs with the exception of one move in the opposite direction to their associated control
surfaces. Which is the exception?
QUESTION 8.
On most jet transports the ailerons will lock out at high speed. Why?
QUESTION 9.
QUESTION 10.
QUESTION 11.
QUESTION 12.
QUESTION 13.
QUESTION 14.
QUESTION 15.
What effect does increasing altitude have on minimum control speed when asymmetric?
QUESTION 16.
QUESTION 17.
Deployment of leading edge high-lift devices will produce a pitching moment. Which way?
QUESTION 18.
QUESTION 19.
QUESTION 20.
What is the difference between fully- powered controls and power-assisted controls?
ANSWERS:
ANSWER 1.
ANSWER 2.
ANSWER 3.
ANSWER 4.
ANSWER 5.
ANSWER 6.
To reduce control input loads by reducing control surface hinge moment Chap 6 page 3
ANSWER 7.
ANSWER 8.
ANSWER 9.
ANSWER 10.
The downgoing aileron (upgoing wing) produces an increase in drag Chap 6 page 24
ANSWER 11.
The downgoing aileron moves less than the upgoing one Chap 6 page 25
ANSWER 12.
At a speed where there is the greatest difference between power available and power required
ANSWER 13.
ANSWER 14.
ANSWER 15.
ANSWER 16.
less power available and therefore less yawing moment Chap 7 page 22
ANSWER 17.
ANSWER 18.
ANSWER 19.
the axis about which the wing will bend or flex Chap 6 page 18
ANSWER 20.
manual reversion is available with power-assisted controls but not with fully powered controls
Stability
Static Stability
Static Longitudinal Stability
Static Directional Stability
Static Lateral Stability
Dynamic Stability
Longitudinal Dynamic Stability
Lateral Dynamic Stability
Asymmetric Effects
Effect of Altitude
8 Stability
1. The four forces acting on an aircraft in straight and level flight, we know, are lift, weight, and
drag. When all the forces acting on it are in balance ie, the sum of the forces and moments is zero,
the aircraft is in a state of equilibrium.
2. Newton's First Law states that a body remains in a state of rest or uniform motion unless
acted upon by an external force. Thus equilibrium can be a state of rest or uniform motion, that is
constant speed and direction. Following a disturbance, stability is concerned with the motion of the
body after removal of the external force. This motion can be considered in two ways. Static stability
describes the immediate reaction of the body, whilst subsequent reaction to the disturbance is
dependent upon dynamic stability.
Static Stability
3. Static stability is the initial tendency of the aircraft to return to the equilibrium position
following a disturbance. The response to the disturbance is termed positive, neutral or negative. If
the body returns to the position it held prior to the disturbance it is said to be positively stable. If the
body takes up a new position of constant relationship to the original position it is said to be neutrally
stable. Negative stability indicates a continuous divergence from the original state. The analogy of a
‘ball and bowl’ is used at Figure 8-1 to demonstrate the above concept.
FIGURE 8-1
Static Stability
4. An aircraft is subject to disturbance about the three axes of movement, roll, pitch and yaw.
Its stability, that is its tendency following a disturbance to return to its original position or to
continue to diverge from that position is therefore considered in relation to those axes. Its stability in
roll, about the longitudinal axis, is known as lateral stability. Its stability in pitch, about the lateral
axis, is known as longitudinal stability. Its stability in yaw, about the normal axis, is known as
directional stability.
6. The horizontal stabiliser is usually placed at the tail of the aircraft (tailplane) however, it can
be placed ahead of the wings in what is referred to as a canard configuration. The main advantage of
the candard design is that the foreplane produces positive lift and for a give speed, a lower angle of
attack is needed on the mainplane resulting in less drag and a reduced stalling speed.
7. The greater the distance the stabilising surface is from the centre of gravity of the aircraft, the
greater its moment arm and therefore the quicker the aircraft will be returned to its original attitude
following a disturbance. This moment arm is often called the tail arm and its length is a measure of
the aircraft’s longitudinal stability.
8. Figure 8-3 shows the way in which the tailplane helps to produce a state of static longitudinal
stability following a pitching disturbance. The success of the tailplane in achieving this relies on the
difference between the angle of incidence of the wing and of the tail. This is known as longitudinal
dihedral. See Figure 8-2.
FIGURE 8-2
Longitudinal
Dihedral
9. When the wing angle of incidence is greater than that of the tailplane the aircraft is said to
have positive longitudinal dihedral, an essential requirement for static longitudinal stability. In
conventional aircraft this is usually achieved with a slightly negative angle of incidence on the
tailplane. From Figure 8-3, if the aircraft is disturbed in pitch, the tailplane will always tend to
restore it to level flight and thus the longitudinal dihedral provides a stabilising influence. The same
effect is achieved if the wing camber is greater than the tailplane camber. Often the tailplane is not
cambered (a symmetrical aerofoil section) or it may even have reverse camber.
FIGURE 8-3
Tailplane
Contribution
10. The stabilising effect of a tailplane will be altered if there is a significant change in the
downwash over it with changing angle of attack. The downwash angle determines the effective angle
of attack of the tailplane, which in turn determines its balancing effect against the wing lift. If, for
example, an increased incidence (pitch up) produces an increased downwash angle, the effective
angle of attack of the tailplane is reduced and its restoring moment is reduced in consequence.
Hence, the longitudinal stability of the aircraft has decreased. In cases where the design of the
aircraft produces this effect, the CG would be moved forward to regain longitudinal stability.
11. It should be appreciated that, although the tailplane produces relatively little lift when
compared with the wing, the distance from the centre of pressure of the tailplane to the centre of
gravity of the aircraft (the arm) is considerable. Consequently the moment produced by the tailplane
is significant.
12. The effect that turbulence will have in inducing a pitching moment of the aircraft will depend
largely on the relative positions of the centre of gravity and the centre of pressure of the wing. At
Figure 8-4 the centre of gravity is shown to be well forward of the centre of pressure. A disturbance
that causes a nose up pitching moment will cause an increase in the angle of attack and an increase in
the amount of lift produced. This will effectively increase the size of the lift/weight pitching moment
(despite a small movement forward of the centre of pressure, which reduces the length of the arm),
and this moment will act to push the nose downwards. In other words a state of static stability will
tend to exist.
FIGURE 8-4
Longitudinal Static
Stability
13. At Figure 8-5 the centre of gravity is aft of the centre of pressure and now a disturbance
which causes the nose to rise will cause an increase in lift which will cause a further (destabilising)
movement of the nose in an upwards direction. Thus it can be seen that the aircraft will be both
statically and dynamically unstable. This is obviously an undesirable situation, and provides a good
reason for always operating any aircraft within the limits of the centre of gravity envelope specified
by the manufacturer.
FIGURE 8-5
Longitudinal Static
Instability
14. To summarise, the factors that affect the static longitudinal stability of an aircraft are the
design of the horizontal stabiliser and the position of the aircraft CG. The horizontal stabiliser in
terms of area, planform, distance of its CP from the aircraft CG and the effect of the wing downwash
upon it. The CG position in terms of movement; aft movement decreases positive stability, forward
movement increases it.
15. However, it must be appreciated that there is a limit to the forward position of the centre of
gravity. The greater the natural stability of an aeroplane due to a forward centre of gravity the more
the elevators must move in order to pitch the nose up during take-off or landing flare. If the centre of
gravity were too far forward there would be insufficient elevator movement available to achieve
these essential pitch control requirements.
16. If the centre of gravity is moved progressively aft there will come a point at which the
destabilising effect of the aft centre of gravity will exactly offset the efforts of the tailplane to produce
a state of positive stability. The position of the centre of gravity at this time is known as the neutral
point, and, with the centre of gravity at this point, the aircraft is in a state of neutral stability. For
obvious reasons the aft limit of the centre of gravity envelope of any aircraft is always forward of the
neutral point.
17. The distance through which the centre of gravity can be moved aft from a given datum to the
neutral point is known as the centre of gravity margin, and is a measure of the longitudinal stability
of the aircraft. The greater the margin the greater the longitudinal stability of the aircraft. It is also
known as the static margin and will be at a minimum when the CG and neutral point are co-incident.
18. If the CG is aft of the centre of pressure the aircraft will be longitudinally unstable.
Conversely, if the CG is forward of the centre of pressure the aircraft will be stable. If the two are
coincident a neutral condition of stability exists.
19. When an aircraft in straight and level flight is subjected to a disturbance that alters its angle
of attack (incidence), there must inevitably be a change in the pitching moment about the CG. For
static stability it is necessary that, if the initial change is nose-up (positive) the resultant pitching
moment must be nose-down (negative), and vice versa. In other words, the rate of change of pitching
moment with changing angle of attack must always be negative. This is illustrated in the graph at
Figure 8-6 of pitching moment coefficient Cm against angle of attack α.
FIGURE 8-6
Graph
20. The negative slope indicates positive static longitudinal stability and the greater the slope, the
greater the longitudinal stability.
21. The trim point shown on the graph at Figure 8-6 occurs at the angle of attack at which the
overall moment about the CG is zero. It is the point where the wing moment is equal to the tail
moment and the aircraft is said to be in trim. The actual angle of attack at which this occurs is
dependent upon the amount of longitudinal dihedral of the aircraft.
Effect of CG Position
22. As the CG is moved aft, the aircraft static stability reduces, becoming neutral then unstable
with continued rearward movement. This is shown at Figure 8-7 where the CG position is defined
with reference to mean aerodynamic chord.
FIGURE 8-7
23. With the CG at the neutral point, neutral static stability exists, the slope of the curve is zero
and there is no change in pitching moment. The neutral point defines the most aft CG position
without static instability.
24. In cases where the CG of the aircraft is significantly moved from its normal position it may
be restored by placing ballast weights in a balancing location. Suppose, for example, an aircraft is to
be ferried empty of passengers or freight over a long distance. It may require a full fuel load that puts
the CG too far aft and this would be balanced by placing ballast in a forward cargo hold.
25. In cases where the vertical force balance changes in flight the aircraft may be re-trimmed for
stable horizontal flight by weight trimming, or the movement of weight within the aircraft. An
example of this can be found in the chapter on High Speed Flight, where fuel is transferred aft in
Concord to balance the aft movement of the centre of pressure during supersonic flight.
27. Figure 8-8 illustrates graphically the effect of elevator deflection. From the curves for various
degrees of deflection it can be seen that the stable negative slope of the CM – CL curves remains
constant, only the position of the trim point varies.
FIGURE 8-8
Effect of Elevator
Deflection on
Graph
29. If the elevators are allowed to float, as in hands-off (or stick-free) flight, they will tend to
align with the free stream flow when the angle of attack of the tailplane is changed. If, for example,
the tailplane angle of attack is increased the elevators will tend to float up, reducing the restoring
moment of the horizontal tail surfaces. Consequently, the stick-free stability of the aircraft is usually
less than the stick-fixed stability.
30. Another way of expressing this is to say that the position of the neutral point will be different
for stick-fixed and stick-free conditions, which will in turn alter the CG margin. The CG margin will
be greater under stick-fixed conditions.
Effect of Trim
31. With a stable aircraft, an increase in CL produces a nose down pitching moment change. In
order to balance this in a new trim condition, the elevator must be deflected upwards to provide the
necessary downward increase in tail lift. The resulting elevator hinge moment is nose-up and to
balance this and trim out the stick force, the trim tab must be deflected downwards, ie. in the positive
sense.
32. Therefore, a positive change in CL is accompanied by a positive change in trim tab angular
deflection.
Wing/Tail Relationship
33. The ratio of the tail volume to the wing volume is the main parameter used by the aircraft
designer in establishing the longitudinal stability of an aircraft. The tail volume is the product of the
tail moment arm and the tailplane area, the wing volume is similarly the product of wing moment
arm and wing area. In both cases the moment arm is the distance from the CP to the aircraft CG.
The greater the tail volume in comparison with wing volume, the greater the longitudinal stability.
34. So what of ‘tailless’ swept wing and delta planform aircraft? With swept wing aircraft the
wing tips can be twisted to reduce their incidence (washout) and they therefore produce the same
effect as a tailplane. With delta wings the reduced incidence is made towards the trailing edge.
Fuselage Contribution
35. The contribution of the fuselage, and to some extent the engine nacelles, is usually de-
stabilising. If the fuselage aerodynamic centre is ahead of that of the wing, then the resulting wing-
fuselage combination aerodynamic centre will be further forward. Effectively, this means that the
aircraft CG is relatively further aft and hence its longitudinal stability is reduced.
36. Furthermore, the induced upwash ahead of the wing increases the de-stabilising influence
from the fuselage and nacelles ahead of the wing. The downwash behind the wing on the other
hand, reduces the de-stabilising influence from the areas of the fuselage and nacelles aft of the wing.
Downwash Changes
37. With an increase in angle of attack, the downwash from the wings is increased which reduces
the effective angle of the tailplane thus reducing its lifting force. Consequently, the restoring
movement provided by the tailplane is reduced and the neutral point would therefore be further
forward and the longitudinal static stability correspondingly reduced.
38. Any factor which alters the downwash at the tail will affect the tail contribution, notably
trailing-edge flap extension and increased wing camber. However, extending trailing-edge flaps also
affects the wing pressure distribution causing a rearward movement of the centre of pressure and a
resulting nose-down pitching moment change, ie. a stabilising effect which now opposes the de-
stabilising effect due to increased downwash. Usually, use of high lift devices is de-stabilising.
Configuration Changes
39. Extension of the landing gear lowers the position of the drag line and additionally, if the
thrust line does not pass through the centre of gravity, variations in thrust with angle of attack
changes, result in pitching moment changes. If the thrust line is high relative to the CG, it is
stabilising, and if low, de-stabilising.
41. It follows that if CL is increased, for example by the use of high lift devices, a reduced elevator
deflection is required for a given trim airspeed. The effect on the elevator position speed graph is
therefore a reduction in the trim speed for zero elevator deflection.
FIGURE 8-9
Elevator Position -
Speed Graph
43. The basic stick-free stability of the aeroplane will require a stick force to maintain a given
attitude that is independent of airspeed, but the force to be balanced by the trim tab is dependent
upon dynamic pressure, or IAS. Therefore, the trim tab setting necessary to maintain the correct
attitude for level flight with zero control column force will vary with airspeed. The faster the speed
the less the angle of attack necessary to maintain level flight, so the less the up elevator deflection
required. The less the elevator deflection required, the less the opposite trim tab deflection needed to
give zero stick force. This is illustrated in the graph at Figure 8-10. The same situation will exist for
an all-moving stabiliser, although the need for force balancing is less, since it is usually moved by
powered controls.
FIGURE 8-10
Effect of Trim Tab
on Stick Force -
Speed Graph
44. For certification, there are criteria of stick force versus speed characteristics laid down by the
JAA and they are as follows:
JAR 25.173(c)
45. The average gradient of the stable slope of the stick force versus speed curve may not be less
than 1 pound for each 6 knots. (The average gradient is taken over each half of the speed range
between 0.85 and 1.15 V trim ).
JAR 23.173(c)
46. The stick force must vary with speed so that any substantial speed change results in a stick
force clearly perceptible to the pilot.
47. If the position of the CG changes whilst trimmed for flight at constant airspeed this must
affect the stick force required to maintain the trim speed. An aft-moving CG will have the effect of
reducing the stick force necessary to alter the pitch attitude of the aeroplane. This is illustrated in the
graph at Figure 8-11. The further aft the CG the shallower the gradient of the stick force – EAS
curve and the less the stick position stability, until the gradient becomes zero at the neutral stability
point. This is when the CG is at the stick-free neutral point, beyond this a condition of stick position
instability will exist. In other words, the stick would have to be pushed at lower speeds and pulled at
higher speeds to maintain attitude.
FIGURE 8-11
Effect of CG
Position on Stick
Force - Speed
Graph
48. Friction in the control system is highly undesirable and can seriously upset the feel of the
controls since it makes it very difficult to determine when the correct trim setting has been applied.
This is because the friction produces a range of force to be overcome, which translates into a range of
trim speeds. The effect is illustrated in the graph at Figure 8-12.
FIGURE 8-12
Effect of Control
System Friction on
Stick Force -
Speed Graph
49. At Mach numbers in excess of 1.0 there is a marked aft movement of the CP and automatic
Mach trim is necessary to cope with the ensuing ‘Tuck Under’. This is explained fully in Chapter 9,
High Speed Flight.
51. The two devices are illustrated at Figure 8-13 and their effect on the stick force – airspeed
graph, which is the same in both cases, is illustrated at Figure 8-14.
FIGURE 8-13
Downspring and
Bobweight
FIGURE 8-14
Effect of
Downspring and
Bobweight on
Stick Force -
Speed Graph
Manoeuvring Stability
52. When an aeroplane is subjected to a pull-up it rotates about its lateral axis. In other words
the nose is rotating up and the tail is rotating down. The effect upon the tailplane is to change the
effective angle of attack so that it is opposing the rotation and providing a restoring moment. Thus,
the stabilising effect of the tailplane is greater during manoeuvring than in steady level flight.
53. The more longitudinally stable an aircraft is, the greater the force necessary to displace it in
pitch. Pitch up is achieved by moving the elevator up, which produces a downward force at the tail
to give the necessary pitching moment. The greater the rate of pitch change the greater the
manoeuvring stability of the aircraft and so the greater the elevator/stick force required. Also, the
greater the rate of pitch change the greater the load factor, or ‘g’ acceleration. Thus it can be seen
that, in a longitudinally stable aircraft, the stick force increase is in direct relation to the g
acceleration, or load factor, n. This is illustrated in the graph at Figure 8-15, which shows a plot of
stick force per g. For a large transport aircraft the stick force per g is deliberately high in order to
prevent inadvertent overstressing of the aircraft through excessive control inputs. Such aircraft have
a lower limit load factor than designs intended for high manoeuvrability and are certified
accordingly.
FIGURE 8-15
Stick Force per ‘g’
Graph
54. The further aft the CG the lower the stick force per g, which is to be expected since we know
that an aft CG decreases longitudinal stability.
55. Manoeuvring stick force can be reduced with adjustment of the trim tab setting, but this is
not usually a recommended procedure since increasing stick force per g is a desirable feature. The
bob weight, mentioned above, has the effect of increasing stick force per g. This is a useful feature if
the basic aeroplane has too low a manoeuvring stick force stability, possibly because of an
inadequate CG margin, and might be added to meet certification requirements. The downspring has
no effect upon manoeuvring stick force stability.
Special Circumstances
56. Ice on an aircraft can greatly increase the surface friction drag and decrease the maximum lift
coefficient of the wing and tail surfaces. The alteration to the drag line, especially where these
surfaces are well displaced from the longitudinal centre line, may result in a significant change in
pitching moment. The weight of the ice may also alter the position of the CG, particularly likely on
swept wing aircraft. In either case the longitudinal stability of the aeroplane will be affected.
57. Similarly, reduction in the lift coefficient of either the wings or the tailplane may alter the
position of the overall CP and thus the CG margin. It must be remembered that an increased CG
margin may be no more desirable, with its decreased control effectiveness, than a decreased one with
its decreased stability. Extending the flaps under these conditions could render a delicate situation
worse and introduce control difficulties at a critical stage of flight.
58. Any other factor that increases local drag or decreases local lift may have effects similar to
those described in the preceding paragraph. Rain can produce limited drag changes, especially at low
speed, as can deformation of the airframe, where the effects are more noticeable at high speed.
60. This is achieved by mounting a vertical stabilising aerofoil at the rear of the fuselage. If the
aircraft is disturbed about the normal axis the vertical stabiliser, or fin, has an angle of attack to the
relative airflow and the sideways lift thus produced has a restoring effect as shown at Figure 8-16.
The fin is a symmetrical aerofoil that produces lift at positive angles of attack (up to the stall).
FIGURE 8-16
61. The larger the surface area of the fin the greater its restoring force, this is illustrated at
Figure 8-17.
FIGURE 8-17
62. Alternatively, the further the fin is set back from the centre of gravity of the aircraft the
greater its restoring moment. Hence, static directional stability may be achieved with a large fin and
a short tail moment or a small fin and a long tail moment, the choice is usually determined by other
design considerations.
1
N = C n --- ρV 2 Sb where b = wing span
2
By transposition:
N
C n = ---------------------
1 2
--- ρV Sb
2
Yaw Angle ψ
64. The yaw angle is defined as the angle by which the aeroplane centreline (the longitudinal axis)
is displaced in azimuth from a given reference. The angle is regarded as positive when the centreline
is to the right of the reference azimuth direction. Yaw angle is only of real significance in wind
tunnel experiments.
Sideslip Angle β
65. The sideslip angle is the angle by which the aeroplane longitudinal axis is displaced from the
relative airflow. The angle is regarded as positive when relative airflow is to the right of the aircraft
centreline. Yaw and sideslip angles are illustrated at Figure 8-18.
FIGURE 8-18
Yaw and Sideslip
Angles
67. When this is plotted graphically as a curve of Cn versus β, the resulting curve will have a
positive slope, the greater the static directional stability of the aircraft, the steeper the slope. If the
slope were to be zero this would indicate a situation of neutral static directional stability. In this
case, if the aircraft were to be subjected to a sideslip angle there would be no tendency to return to
the original heading (no weathercocking effect). An aircraft exhibiting static directional instability,
upon being subjected to a sideslip angle, would continue to diverge from the original heading and
this would appear as a negative slope on the Cn - β graph.
68. A graph of Cn versus β is shown at Figure 8-19. It will be noted that at high sideslip angles
the curve becomes horizontal, indicating neutral static directional stability, and at greater angles
becomes negative, indicating instability. This is due to the aerodynamic stalling of the fin and should
not occur within the normal manoeuvring limits of the aircraft.
FIGURE 8-19
Cn – β Graph
Centre of Gravity
69. The position of the aircraft CG will influence the effectiveness of the fin in achieving static
directional stability. The further forward the CG the longer the moment arm and the greater the
restoring moment. Once again it is evident that it is highly undesirable to operate an aircraft with
the CG aft of permissible limits.
Wing Effect
70. The two wing design features which contribute to the directional stability of the aircraft are
dihedral and sweepback, although the former is relatively insignificant particularly when compared
to the latter.
71. The inclination of the wings towards the tips associated with dihedral, effectively tilts the lift
vector thus producing a destabilising contribution to the yawing movement due to yaw. On the other
hand, with sweepback, it is the component of the relative airflow normal to the leading edge (or to
the line of aerodynamic centres in the case of a wing whose leading and trailing edges are not
parallel) which is responsible for the drag of the wing as shown in Figure 8-20. The drag therefore
of the leading (starboard) wing is greater than that of the trailing wing due to its reduced effective
sweep angle and is thus a stabilising influence. This effect is of course significant when the
sweepback angle is large.
FIGURE 8-20
Effect of
Sweepback on
Static Directional
Stability
Fuselage Effect
72. The fuselage has a generally destabilising effect upon aircraft static directional stability. This
is because, in subsonic flight, the CG is usually well aft of the centre of pressure of the fuselage.
Hence, in the event of sideslip the relative airflow exerts a greater yawing moment forward of the CG
than aft of it. This is the reason why an aircraft needs a vertical stabiliser (fin), to overcome the
destabilising influence of the fuselage. The effect is often noticeable at high angles of attack, when
the fin is stalled by the disturbed airflow from the fuselage and the aircraft becomes directionally
unstable.
73. To counter this, strakes or ventral fins are sometimes fitted. These are flat plates or strips
attached to the underside of the rear fuselage and running parallel to the aircraft centreline, forming
a keel surface aft of the CG. They increase the directional stability in normal flight and help
maintain it even if the fin begins to stall. Such devices are generally found on short-bodied training
and military aircraft, rather than large transports. Another device is the use of multiple vertical tails,
either in the form of twin fins as seen on many modern fighter aircraft or small tailplane mounted
additional fins, as seen on some larger aircraft.
Dorsal Fin
74. The dorsal fin is an extension of the fin, running forwards along the top of the fuselage, as
illustrated at Figure 8-21.
FIGURE 8-21
Dorsal Fin
75. The function of the dorsal fin is twofold. It significantly increases the side surface area aft of
the CG and thereby increases the static directional stability of the aircraft by increasing the yawing
moment and thus the weathercocking effect. Secondly, by reducing the effective aspect ratio of the
vertical fin it increases its stalling angle of attack. Thus the fin remains effective at greater sideslip
angles.
Fin Sweep
76. An alternative way of reducing the fin aspect ratio to increase its stalling angle is to sweep it
backwards. This also has the benefit of moving its centre of pressure slightly rearwards, increasing
the yawing moment of the tail.
FIGURE 8-22
Effect of Aircraft
Components on
Static Directional
Stability
Propeller Slipstream
78. The propeller of a single-engine aircraft produces a swirling slipstream that is apt to strike
one side of the vertical tail more strongly than the other. This creates a directional control
requirement from the rudder, which must balance the asymmetric airflow and prevent sideslip. The
result is usually that the aircraft is more prone to sideslip in one direction.
FIGURE 8-23
Roll Damping
80. However, in addition to the rolling motion produced by a disturbance about the longitudinal
axis, the aircraft also experiences a sideslipping motion due to the inclination of the lift vector as at
Figure 8-24.
FIGURE 8-24
Sideslipping
Motion
81. The static lateral stability of an aeroplane is a measure of its tendency to return to wings-level
flight when it has been disturbed in roll. The tendency to recover from such a disturbance is always
reliant upon the effects of sideslip upon the aeroplane.
82. As well as the rolling moment due to sideslip, the sideslip will also produce a yawing moment,
the strength of which will depend upon the static directional stability. However, when considering
the static lateral stability we need only consider the relationship between sideslip and rolling
moments.
1
L = C1 --- ρV 2 Sb
2
Therefore by transposition:
L
C 1 = ---------------------
1 2
--- ρV Sb
2
85. When plotted as a curve of rolling moment coefficient Cl against sideslip angle β the slope of
the curve should be negative. If the slope is zero this represents neutral lateral stability and if it is
positive the aircraft is exhibiting lateral instability, as shown at Figure 8-25.
FIGURE 8-25
Rolling Moment
Coefficient
Sideslip Angle
86. The aircraft design features which affect static lateral stability are:
Dihedral
87. Dihedral has been defined in an earlier chapter as the upward inclination of the wing to the
plane through the lateral axis. The purpose of this wing form is solely to make improvements to the
lateral stability of the aircraft. Figure 8-26 shows the effect of dihedral on lateral stability.
FIGURE 8-26
Dihedral Effect
88. Because of the wing dihedral and the sideslip, the effective angle of attack of the lower wing is
greater than that of the upper. Thus the lift produced by the lower wing is now considerably greater
than that produced by the upper, producing a rolling moment to roll the wings back towards the level
position. Hence, dihedral improves the lateral stability of an aircraft and is in fact one of the most
important contributions to the overall stability. It is for this reason that lateral static stability is often
termed the ‘dihedral effect’. Other design features which also contribute to static lateral stability
therefore can be considered to increase the effective dihedral of the wing.
Anhedral
89. From the foregoing it should be apparent that anhedral, a downward inclination of the wing
to the plane through the lateral axis, will have the opposite effect to dihedral. Where laterally
stabilising features such as large fin surfaces and swept wings are essential for other purposes, such as
high-speed flight, it may be necessary to deliberately introduce laterally destabilising features.
Anhedral is often used for this purpose and many examples are currently in service.
Swept Wings
90. Wings which are swept backwards from root to tip also have a stabilising effect, as illustrated
at Figure 8-27. The swept wing increases lateral stability because, when an aircraft rolls to one side,
it also tends to sideslip in that direction. In a swept wing aircraft this has the effect of decreasing the
effective chord length, and increasing the effective span, of the downgoing wing (i.e. increasing its
aspect ratio compared to the upgoing wing). The resultant extra lift generated by the high aspect
ratio wing creates a rolling moment to roll the aircraft back to wings level. It is generally reckoned
that 10° of sweepback will provide the same stabilising effect as 1° of dihedral.
FIGURE 8-27
Effect of
Sweepback on
Lateral Stability
Wing Location
91. High-winged aircraft, that is aircraft with the wings mounted above the centre of gravity and
longitudinal axis, are more laterally stable than mid-wing or low wing aircraft.
92. It is often incorrectly thought that mounting the wings above the centre of gravity improves
lateral stability due to a pendulum effect. In fact it is the effect of sideslip that provides the restoring
force. The lift of the lower wing will be greater than that of the upper, since the sideslip flow
component induces a circulation tendency around the fuselage, increasing the angle of attack of the
lower wing.
93. Often high wings are chosen by the designer so that ground clearance can be maintained
below the engine pods or the propeller tips. If the lateral stability due to the high wings is greater
than required anhedral may once again be used to reduce lateral stability. No doubt the student can
think of several examples.
Fin Size
94. A large fin area will increase lateral stability, since the relative airflow in the sideslip provides
a righting moment. The higher the centre of pressure of the fin is above the centre of gravity the
greater the rolling moment and therefore the greater the lateral stability of the aircraft. This is
illustrated at Figure 8-28.
FIGURE 8-28
Effect of High Fin
on Lateral Stability
Ventral Fin
95. If there are side surfaces below the centre of gravity these will produce a moment, during
sideslip, which increases the rate of roll. Such keel surfaces increase lateral instability. Some aircraft
have, for example, a tall fin to support a tee tailplane clear of turbulent downwash from the wing.
Such an aircraft may be laterally stable to such a degree that roll response is poor, so a keel surface
(or ventral fin) is introduced deliberately to improve roll response.
Cross-Wind Landings
98. It is desirable that an aircraft should exhibit a degree of lateral stability. However, if roll due
to sideslip is too great this can create handling difficulties during crosswind landing and take-off and
may render roll control difficult as well.
99. On an approach to land with the aircraft ‘crabbing’ into a cross-wind, the aircraft has to be
yawed to align it with the runway prior to touchdown. Sideslip will thus be increased in the opposite
direction to the yaw and, with high lateral stabilising design features, the aircraft will roll away from
the sideslip, i.e. sideslip right, roll left.
100. Generally speaking it is desirable from a handling point of view that the aeroplane should
have weak positive lateral stability.
Dynamic Stability
101. Dynamic stability considers the change in the state of stability of a body with the passage of
time. If, following a disturbance, the deviation of a body from its original position diminishes, the
body is said to be dynamically stable. If the induced oscillation remains constant a state of neutral
dynamic stability exists. If the induced oscillations increase in magnitude the body is said to be
dynamically unstable. These conditions are illustrated at Figure 8-29.
FIGURE 8-29
Dynamic Stability
FIGURE 8-30
Longitudinal
Dynamic Stability
103. The phugoid, a rather pompous term invented by the eminent nineteenth century scientist
Lanchester, is a long period oscillation in which both aircraft speed and height vary considerably
with its change in angle of attack. For example, following a disturbance causing an increase in
forward speed, there will be an increase in drag, resulting in a reduction in speed. In addition there is
an increase in lift which results in an increase in height and this increase in height further reduces
speed until it is below the pre-disturbed value. Now the aircraft begins to descend once more and an
oscillatory motion is observed where height gain and speed loss are followed by height loss and speed
gain. The extent to which the phugoid oscillation is damped by the horizontal stabiliser depends
largely upon the drag characteristics of the aircraft. Modern low drag jet transporters are
particularly susceptible to phugoidal oscillation but since it is a long period oscillation, is easily
corrected.
104. The short-period oscillation comprises rapid oscillations in pitch, involving large changes in
load factor but only small changes in speed and height. Such an oscillation may result from a vertical
gust causing an increase in angle of attack and lift, resulting in a change in pitching moment. Since
the frequency of this level of oscillation is usually high, it is termed a short-period oscillation.
However, if this oscillation is dynamically unstable, any correction necessary to eliminate it will be
continually changing in sense, in phase with the oscillation itself. Furthermore, because of the short
period, it may not be possible for the pilot to apply unstable in-phase corrections due to pilot
response lag and control system lag producing a negative damping effect. This is referred to as pilot
induced oscillations. Their magnitude can reach alarming proportions extremely quickly and are
most likely to occur under conditions of high dynamic pressure eg, high speed/weight at low altitude
and excessive pilot response lag or tendency to over control. If pilot induced oscillations are
encountered, the conditions should be controlled or released to allow inherant dynamic stability of
the aircraft to damp out the oscillations.
105. The damping effect of the tailplane, essential to the maintenance of longitudinal stability, is
reduced in the low-density atmosphere at altitude. For a given IAS, the TAS increases with altitude
and therefore so does inertia. In other words the aerodynamic damping will have less effect
Roll Damping
107. The rolling motion will initially only affect the angle of bank and will be quickly damped as
explained in Static Lateral Stability, Paragraph 79.
Spiral Instability
108. When an aircraft drops a wing the magnitude of the righting forces due to fin area, dihedral,
high wing, etc, determines the degree of lateral stability. The fin and keel surfaces, however, tend to
yaw the aircraft into the airflow, in the direction of the lower wing. The higher wing, which is now
on the outside of the turn (the result of the yaw) is travelling slightly faster than the lower wing and
developing more lift. This adds to the rolling moment of the original disturbance, opposing the
righting forces and, possibly, exceeding them. This in turn causes the bank angle to increase further.
109. If the situation described above exists, the aircraft will enter a progressively steeper diving
turn, or spiral dive. This is known as spiral instability, and it occurs when an aircraft's directional
stability is greater than its lateral stability. However, the roll and yaw rates will be reduced by roll
and yaw damping, the cross-coupling moments will be consequently of a reduced magnitude and the
spiral dive tends to become neutral or even stable. A reduction in fin area, reducing the directional
stability, will reduce spiral instability.
110. Spiral instability is a common feature in many aircraft and is not of particular importance,
since it is easily overcome with normal control correction. Nevertheless, if uncorrected, the spiral
divergence will persist and speed increases as pitch attitude reduces, roll attitude increases and
altitude is lost.
Dutch Roll
111. Dutch roll is a combination of yawing and rolling motions, and occurs more readily with
swept wing than with straight wing aircraft.
112. The secondary effect of yaw is roll. This occurs because, with a yaw to the left, the left wing
effectively slows down (less lift), whilst the right wing speeds up (more lift), causing a roll to the left.
Wing sweepback increases the secondary effect due to a change in aspect ratio. This reduces the
tendency of the wings to dampen the rolling motion, which then leads to sideslip. If the oscillatory
yawing and rolling motion thus induced maintains constant amplitude a state of neutral Dutch roll
exists. If the oscillations diminish in magnitude (without control input) a state of stable Dutch roll
exists. If the amplitude of oscillations increases the aircraft is unstable. Dutch roll is difficult to
counter manually and may be exacerbated to a hazardous degree if control inputs are out of phase
with the rolling and yawing motion.
113. The factors leading to Dutch roll are a combination of relatively weak directional stability
compared with lateral stability. Hence, any departure from wings level attitude is rapidly corrected,
but the aircraft has little or no tendency to turn into the sideslip (and may even turn away from it).
Thus the aircraft has a wallowing tendency.
114. It is invariably considered necessary with modern jet transport aircraft to relieve the pilot of
the requirement to control Dutch roll by incorporating yaw dampers into the system.
115. A yaw damper is an electro-hydraulic system. The yaw is sensed by gyros, and the direction
and rate of yaw is used to operate the hydraulic jacks controlling the rudder. Thus any unintentional
yaw is dealt with before it becomes oscillatory.
Roll Dampers
116. In addition to yaw dampers, some aircraft have roll dampers that are also gyroscopically
controlled to correct roll by applying either aileron or asymmetric spoiler. This is particularly useful
in turbulent conditions and, whilst not specifically fitted to counter Dutch roll, will obviously assist
in doing so.
Asymmetric Effects
117. The stability of an aircraft (its ability to recover from a disturbance) will be degraded if it is in
an asymmetric condition, in terms of power or drag, at the time of the disturbance. The asymmetry
can cause one wing tip to stall, resulting in roll and yaw to such an extent that the aircraft enters a
descending spiral path, or spin. This was discussed in depth in the section on Stalling.
118. The engines of multi-engine aircraft are positioned equidistant from the aircraft centreline so
that their thrust is symmetrical about the normal axis and does not produce a yawing moment.
119. In the event of an engine failure the resultant asymmetry of thrust and drag produces (with
the exception of a few three-engine examples), a strong yawing moment towards the failed engine.
The aircraft is thus sideslipping away from the failed engine and with high static lateral stability
characteristics, would roll towards the failed engine. Under conditions of high power setting and low
forward speed, i.e. on take-off or go-around, the ensuing wing drop may be further increased by a
large corrective aileron deflection. The yawing moment created by the engine failure has to be
countered with the use of considerable rudder, accentuated by the higher power/lower speed
situation which adds more drag and reduces the available control authority. The reduction in power
available increases response times to demands for increased power.
Effect of Altitude
120. With increasing altitude, aerodynamic damping decreases due to the reduction in the density
of the air. The damping moment in pitch, provided by the tailplane for longitudinal stability, in yaw,
provided by the fin for directional stability and in roll, by the differential lift caused by the upgoing
and downgoing wings for lateral stability, is proportional to dynamic pressure and inversely
proportional to TAS. As altitude increases, at a constant EAS, the TAS increases and consequently
damping reduces, as shown at Figure 8-31.
FIGURE 8-31
Effect of Altitude
on Static Stability
121. As we know, a tendency to Dutch roll occurs when lateral stability is greater than directional
stability, whereas spiral instability is common when directional stability is strong in comparison to
lateral stability. With increasing altitude both lateral and directional stability reduce, however,
directional stability reduces at a greater rate than lateral stability. Consequently, the tendency to
Dutch roll increases and to spiral instability reduces with increasing pressure altitude.
Aerodynamic Heating
Mach Buffet
Buffet Boundary
Tuck Under
Mach Trim
Lateral Stability
Vortex Generators
The Supercritical Wing
Oblique Shock Waves
Mach Cone
Aircraft Weight
Expansion Waves
Centre of Pressure
2. We already know all about the streamlines involved in low speed flight. Although the flow is
somewhat different at supersonic speeds, the behaviour of the airflow is stable and predictable. It is
principally in the transonic envelope (the range from the critical Mach number up to an aircraft
speed slightly in excess of Mach 1.0), that control and stability problems arise, since the airflow
consists of both subsonic and supersonic elements.
4. True Mach number is therefore the ratio of true airspeed to the local speed of sound, and may
be expressed as:
TAS
True Mach No = ------------
LSS
Speed of Sound
5. The speed of sound is the speed at which a very small pressure disturbance is propagated
through a fluid medium at a given temperature.
7. Remember that 0°C = +273°A. Therefore, as temperature decreases with altitude so does the
LSS.
TAS
True Mach No = ------------------------------------------------------------------
38.94 ( Temperature ( °A ) )
Example 1
9. From the formula above it can be seen, for example, that if TAS is constant then true Mach
number will change with varying altitude in the standard atmosphere since temperature, and thus
LSS, will change.
10. Find the local speed of sound at sea level in the International Standard Atmosphere.
12. An aircraft flying at Mach 1.0 at ISA mean sea level would have to be flying at a true airspeed
of 661 knots, since:
661
Mach1.0 = ---------
661
Example 2
13. An aircraft is to fly at Mach 0.85 at FL 350, where the ambient air temperature is -55°C.
What will be its true airspeed?
TAS
MachNo = ------------
LSS
16. TAS is a function of pitot excess pressure (the difference between pitot and static pressure)
and density. LSS is a function of static pressure and density. Density is common to both functions.
Thus TAS and LSS may be expressed as pressure ratios, and it is this that the Machmeter measures.
It employs an airspeed capsule (CAS) and an altimeter capsule (static pressure) working in
combination.
dynamic pressure
Indicated Mach Number is thus proportional to ------------------------------------------
static pressure
17. From this it may be seen that, for example, flight at constant CAS and constant flight level
will give a steady machmeter reading, since neither dynamic nor static pressure are changing, even if
temperature changes. It may also be seen that, for example, at constant CAS in the standard
atmosphere the machmeter reading will change if altitude changes since the static pressure will
change.
18. A full explanation of the working of a machmeter may be found in the Flight Instruments
book, Chapter 1.
Compressibility
19. When considering flight at low subsonic speeds it is convenient to regard air as an
incompressible fluid, since the pressure changes which occur are relatively small and the consequent
changes in density are negligible and can be ignored. At higher flight speeds the pressure variations
which occur as air flows over the aeroplane are much greater and give rise to significant changes in
air density.
20. Hence, when considering high-speed flight the air must be regarded as a compressible fluid
and account taken of the compressibility effects on the aircraft and particularly on the lift-producing
surfaces. Any body moving through the air creates pressure waves, which travel away from the body
in all directions at the speed of sound. If an aircraft is travelling at less than the speed of sound the
pressure waves ahead of the aircraft can travel away from it, as illustrated in the diagram at
Figure 9-1.
FIGURE 9-1
Pressure Wave
Propagation
21. However, if the aircraft is travelling at the speed of sound the pressure waves ahead of the
aircraft can no longer escape and a compression wave builds up at the leading edge. All changes in
pressure and velocity occur across this compression wave and consequently occur much more rapidly
than in the subsonic case, where changes begin ahead of the aircraft. Because of this the
compression, or pressure, wave is often referred to as the shock wave. The effect is illustrated in the
diagram at Figure 9-2. The shock wave is formed perpendicular, or normal, to the direction of flight
and is known as a Normal Shock Wave. The flow immediately behind a normal shock wave is
subsonic.
FIGURE 9-2
Normal Shock
Wave
22. Since the shock wave forms at the leading edge, the pressure and velocity distribution over the
wing behind the wave is altered. This can cause significant variations in local values of lift and drag,
altering the pitching moment on the wing and therefore the aircraft trim. These variations and the
disturbed airflow arising from them may also affect control operation.
23. It should be noted that the aircraft does not necessarily have to be flying at Mach 1.0 to
experience compressibility effects. Because the function of an aerofoil is to accelerate the airflow
over it, the air speed at some point on the aerofoil can be sonic or supersonic even though the
aerofoil is moving through the air at less than the speed of sound. In other words, it is possible to
have both subsonic and supersonic airflow on different parts of the aircraft at the same time. This is
known as transonic flight and, as a general rule, occurs between Mach 0.75 and Mach 1.2. Below
Mach 0.75 the airflow on all parts of the aircraft is subsonic, whilst above Mach 1.2 it is supersonic.
24. The free stream Mach number (MFS) is the Mach number of the airflow at a point unaffected
by the pressure of the aircraft, but measured relative to the aircraft.
25. The local Mach number (ML) is the speed of the air relative to LSS measured at a specified
point on the aircraft. The local Mach number may be greater than, the same as, or less than MFS.
26. The critical Mach number (MCRIT) is the lowest free stream Mach number at which a local
Mach number of 1.0 will occur at any point on the aircraft. MCRIT varies with the angle of attack,
since the higher the angle of attack the greater the acceleration of air over the top of the wing, and
therefore the sooner the air over the wing will go supersonic. MCRIT marks the lower end of the
speed range within which ML may be either subsonic or supersonic.
27. Compressibility Mach number is the Mach number at which compressibility effects cause
significant control problems, and beyond which loss of control is probable.
28. Finally, critical drag Mach number relates Mach number to an appreciable increase in drag
that is associated with compressibility effects. The critical drag Mach number is normally 110% to
115% of MCRIT.
29. Remember that the free stream Mach number (MFS) can be well below Mach 1.0 for a shock
wave to form since, providing the speed is in excess of MCRIT, ML on the upper surface will be in
excess of 1.0.
30. When this occurs a shock wave forms over the upper surface of the wing because the pressure
waves from the rear of the wing are trying to move forward, and are meeting air travelling
backwards at exactly the same speed. The point at which this shock wave usually forms is just aft of
the point of maximum camber of the wing where the acceleration of the air is greatest. In front of
the shock wave the flow is at or beyond Mach 1.0, whilst behind the shock wave the flow is still
subsonic. It should be appreciated, therefore, that a shockwave forms where the airflow goes
subsonic, not supersonic
31. At the shock wave, the normal laws of physics seem to break down, and as the air passes
through the shock wave the pressure increases, as does the temperature and density. If the speed of
the aircraft is increased still further the region of supersonic flow on top of the wing also increases
and the shock wave will start to move back towards the trailing edge. On the under surface the
curvature of the wing is usually less than on the upper surface, and the shock wave will form later.
However, once having formed, if the actual speed of the aircraft is further increased, the lower
surface shock wave will also move rearward.
32. As MFS reaches 1.0 both the upper and lower shock waves arrive at the trailing edge of the
wing. At some time another shock wave, known as the detached bow wave, forms just in front of the
leading edge. As MFS is increased well above 1.0 the forward shock wave moves back to actually
touch the leading edge, and is now known logically enough, as the attached bow wave. At this point
both the forward and aft shock waves are at the position at which they will remain as speed is further
increased. All that will happen now is that, as speed is further increased, the waves will bend further
backwards at points removed from the wing itself.
FIGURE 9-3
Shock Wave
Formation
34. The bow wave and tail wave of an aircraft at supersonic speed are sufficiently strong to reach
the surface of the earth causing a ‘sonic boom’. Whilst normally heard as one disturbance, there are,
in fact, two very close together. The actual pressure disturbance is small. For example, Concorde at
mach 2 and 52000 ft altitude leaves an overpressure of 1.94 pounds per square foot over the surface,
which is not great compared to the standard atmospheric pressure of 14.7 pounds per square inch.
The ‘mach cone’ angle at mach 2 is 60 degrees. This is illustrated at Figure 9-4.
FIGURE 9-4
Mach Cone
Wave Drag
35. For an aircraft that is not designed for transonic or supersonic flight, the formation of shock
waves will have a dramatic effect on both lift and drag. The stability of the aircraft may become
critical, and control difficult, or in the extreme impossible.
36. Basically, the cause of these problems is the separation of the airflow behind the shock wave
due to the rise in pressure that occurs. Separation within the boundary layer creates a considerable
increase in drag and reduction in lift. The drag thus produced is termed wave drag, and is
particularly marked at MCRIT. As the speed is further increased the shock wave moves towards the
trailing edge, with a resultant decrease in wave drag and increase in lift. As a MFS of 1.0 is achieved
the shock wave reaches the trailing edge. Beyond a MFS of 1.0 the problems of transonic flight are
left behind (literally), although the amount of lift produced will be lower than at subsonic speed for a
given angle of attack. This is because the co-efficient of lift is reduced in supersonic flight, due to the
presence of the bow wave.
37. Figure 9-5 shows the variation of the co-efficient of drag through the transonic phase and
Figure 9-6 shows the variation of the co-efficient of lift against Mach number.
FIGURE 9-5
Variation of C D
Through the
Transonic Range
FIGURE 9-6
Variation of C L
Through the
Transonic Range
38. In order to reduce the effect of wave drag, shock waves must be kept as weak as possible. To
achieve this the wings of supersonic aircraft are designed with a sharp leading edge to minimise the
bow wave, together with a thin wing with minimal camber to reduce the adverse pressure gradient.
This is discussed in further detail in the subsequent section entitled Aerofoil Thickness.
Control Deflection
39. The effect of the conventional hinged flap type of control surface when deflected is to create
an aerodynamic force ahead of the control that is usually greater than that produced by the control
surface itself. When a shock wave is established on the associated lifting surface ahead of the control
surface this is no longer the case, since pressure variations cannot be transmitted forward through a
shock wave. Consequently the effect of deflecting the control surface is reduced, since only the flow
over the control surface is modified. When the shock wave becomes established at the trailing edge,
the effectiveness of the control is even further reduced.
40. This has led to the replacement of the tailplane and elevator configuration with the all-
moving horizontal stabiliser in high-speed aircraft. As has been previously mentioned, instead of
ailerons at the wing tips, differential spoilers and/or inboard ailerons are used in the transonic region
of flight. This is partly due to the effects described in the previous paragraph and partly due to the
wing twist caused by aileron deflection at high speed, which can negate or even reverse the effect of
the ailerons.
41. When the shock wave is actually located on the control surface its deflection will cause the
wave to move, with consequent large alterations of the position and magnitude of the aerodynamic
forces acting on the control. This may result in high frequency vibration of the control surfaces,
known as control ‘buzz’.
42. Deflection of the controls during transonic flight usually requires much greater input forces
from the pilot’s controls. This is because the hinge moment of the control surface is changed by the
changing forces as the shock wave forms first ahead of the control, then at the hinge and finally at
the trailing edge. Almost invariably power-operated controls are essential in order to overcome the
large and variable stick forces encountered in aircraft designed to operate in this regime.
Angle of Attack
43. Increasing the angle of attack has the effect of reducing the critical Mach number (MCRIT) of
the aircraft. This is because as angle of attack increases, the local peak velocity over the wing is
increased. This is of particular significance when one considers that effective angle of attack
increases during manoeuvring, hence manoeuvres when flying at high speed may induce the
formation of a shock wave at a free stream Mach Number lower than the steady level flight value.
Aerofoil Thickness
44. In order to avoid the complications of flight in the transonic region, it is clearly highly
desirable for aircraft that are to fly at high subsonic speed to have a high critical Mach number. One
of the ways of increasing the critical Mach number is to reduce the thickness/chord (t/c) ratio of the
aerofoil sections, which reduces the flow acceleration over the section. The benefits are further
enhanced if the camber is kept low, with the point of maximum thickness at about 50% chord. This
has the effect of reducing the intensity of the shock waves when they form and ensuring that they
form well back towards the trailing edge. Thus less of the wing surface is affected by the adverse
conditions behind the wave.
45. It will be remembered that thickness/chord ratio is the ratio of maximum aerofoil thickness to
chord length, expressed as a percentage. This can therefore be achieved with a thin wing of narrow
chord, or a thicker wing of broad chord. The disadvantages of a thin aerofoil section are that it is
susceptible to flexure and twisting and it has a lower maximum lift coefficient. Because of its
thinness it is difficult to incorporate the chord-extending trailing edge flaps necessary to improve the
lift coefficient at low flight speeds.
46. A broad chord wing, such as the delta planform of the Vulcan bomber, can be made thicker
for the same t/c ratio, but has its own structural and low-speed handling limitations, that render it
generally unsuitable for high volume passenger transport aircraft.
47. Consequently a compromise has to be reached, giving the highest practicable t/c ratio in a
wing capable of incorporating adequate lift augmentation systems for landing and take-off. The
maximum MCRIT for subsonic transport aircraft is usually of the order of 0.85. From the graph at
Figure 9-7 it will be seen that this can be achieved with a straight wing of 7.5% thickness/chord
ratio.
FIGURE 9-7
Effect of
Thickness/Chord
Ratio on MCRIT
- Straight and
Swept Wing
Angle of Sweep
48. From the graph at Figure 9-7 it will be seen that the critical Mach number for a wing of given
thickness/chord and aspect ratios can be greatly increased by sweep back. Given the stowage
requirements for fuel, flaps and possibly landing gear in the wings of a transport aircraft, together
with the requirement for a reasonably high aspect ratio, a t/c ratio of at least 10% - 15% is necessary.
A 45° sweep back as shown in Figure 9-7 is generally impractical for a large transport aircraft, but
even with a much more modest sweep angle a satisfactorily high critical Mach number can be
obtained at the t/c ratio required.
49. The control effect produced by ailerons on a swept back wing can be considerably reduced
due to the fact that they are not mounted perpendicularly to the relative airflow, and this is
illustrated at Figure 9-8. Also, the effect of ailerons can be reduced in high-speed flight due to the
twisting effect on the aircraft's structure, as previously mentioned.
50. For the foregoing reasons many jet aircraft are fitted with two ailerons per wing. The
outboard ailerons are used for low speed flight in the conventional manner, and have the advantage
of a long force couple. During high-speed flight the outboard ailerons are locked and the inboard (or
high-speed) ailerons are used.
51. The force couple is very much reduced with the inboard ailerons, but this is offset by the high
speed, and anyway rapid rates of roll are not required during high-speed flight. The important thing
is that, since the high-speed ailerons are mounted on a structurally rigid (thick and deep) part of the
wing, any wing twist that is produced will be minimal. The function of the spoilers, which are
shown at Figure 9-8 was discussed in Chapter Six.
FIGURE 9-8
Primary and
Secondary
Controls on a
Swept Wing
52. Broadly speaking, the major advantage of a swept back wing is that of the increase in the
critical Mach number, but it does also reduce both the rate at which the drag coefficient rises with
increasing Mach number, and the maximum drag coefficient. This is illustrated in the graph at
Figure 9-9. It will also be noted from Figure 9-9 that beyond about Mach 2.0 the advantage of
sweep back is minimal.
FIGURE 9-9
Effect of Mach
Number on C D
53. Many of the disadvantages of swept wings are solved by the use of the variable geometry
wing (as in the Tornado) whereby the sweep can be altered mechanically. This is a rather complex
system involving an increase in weight and structural complexity and for this reason, to date, it has
been confined purely to military aircraft.
Area Rule
54. It can be shown theoretically that there is a certain ideal shape for a transonic or subsonic
aircraft that will produce minimum drag. It was stated earlier that reducing the thickness and
camber of the wing, thereby avoiding sharp pressure and velocity peaks, could reduce the intensity of
the shock wave on a wing. The same is true of the aeroplane as a whole and the ideal graphical
distribution of cross-sectional area along the longitudinal axis is a smooth curve, as illustrated at
Figure 9-10.
FIGURE 9-10
Ideal Body of
Revolution
55. If the cross-sectional area of a ‘conventional’ aircraft is plotted against its longitudinal axis,
the wings and empennage (tail surfaces) tend to appear as lumps on the curve. However, if the
fuselage contours are increased ahead of and behind the wings and empennage, a smooth curve can
be obtained as shown at Figure 9-10.
FIGURE 9-11
Area Rule
FIGURE 9-12
Effect of Mach
Number on
Stalling Angle
FIGURE 9-13
Effect of Mach
Number on
CLmax
Aerodynamic Heating
59. As any body moves through the air the surface friction creates heating. The faster the body
moves the greater the friction and therefore the greater the heat generated. In addition to this,
pressure builds up, particularly at the stagnation points, and from the gas laws we know that when a
gas is compressed its temperature increases. Once again, the higher the airspeed the greater the total
pressure and the greater the resultant temperature.
60. At speeds below Mach 2.0 this heating effect is of no great importance from a structural point
of view, but beyond that it is necessary to use heat resistant structural materials. Between Mach 1.0
and Mach 2.0 the surface temperature of the aircraft can rise to a point where maintaining a
comfortable cabin temperature for passengers becomes problematical.
61. Figure 9-14 shows graphically the surface temperature rise with Mach number at an altitude
of 28,000 ft, where the ambient air temperature is -40°C.
FIGURE 9-14
Effect of Mach
Number on
Surface
Temperature
62. Various methods can be used to dissipate the heat generated, or to insulate the aircraft
interior from it. Very high-speed military aircraft and space re-entry vehicles employ surface
materials able to withstand the high temperatures and which, in some cases, encourage heat
dissipation by radiation. Concorde employs a system in which fuel is circulated through channels
just beneath the exterior surface to dissipate heat by conduction.
Mach Buffet
63. The turbulent airflow that occurs behind a shock wave is liable to cause severe buffeting,
especially if this turbulent flow affects the horizontal stabiliser surfaces. The symptoms are very
similar to that of the stall, hence the term, ‘shock stall’, applied to the phenomena. The major
difference between this and the stall discussed in Chapter Four is that the ‘conventional stall’ occurs
because of excessive angle of attack and is correctly referred to as the high-incidence stall. The shock
stall is much more likely to occur at low angles of attack and is caused by shock-induced separation.
(See Figure 9-3).
64. Another cause of Mach buffet, noticeable particularly with supercritical aerofoil sections, is a
tendency for the relatively weak shock wave to move rapidly backward and forward on the surface
of the wing as MCRIT is reached.
Buffet Boundary
65. Because of the high altitude at which jet transport aircraft normally operate the cruising
speed, which is ideally just below MCRIT, and the high-incidence stalling speed are remarkably close
to each other, sometimes less than 20 knots separates the two. Because of the low temperature at the
operating altitude the local speed of sound is low and the cruise TAS will be very close to that needed
to achieve MCRIT. The very narrow margin between the clean aircraft high-incidence stall speed and
the shock stall speed is known as the buffet boundary. It is also known colloquially as ‘coffin
corner’.
Tuck Under
66. In the transonic range there is usually a marked change in the pitching moment, producing a
nose-down effect. This can be due to a number of factors. The position of the shock waves on the
upper and lower surfaces is not usually coincident between MCRIT and Mach 1.0, the lower one
usually being forward of the upper. This tends to move the centre of pressure aft, creating a nose-
down moment. In swept wing aircraft shock waves tend to form on the thicker inboard wing
sections first, which means that there is a loss of lift near the roots and so the centre of pressure
moves aft because of the sweep back. Finally, loss of downwash over the horizontal stabiliser
reduces its balancing downward force resulting in an increased nose-down pitching moment. This
nose-down pitching tendency at high subsonic/transonic speeds is sometimes referred to as ‘tuck
under’.
Mach Trim
67. The effect of the pitch down moment described in the preceding paragraph is to tend to make
the aircraft speed unstable as well as longitudinally unstable. That is to say, failing any corrective
action, the nose-down pitch causes the speed to increase, which causes further nose-down pitch,
which causes the speed to increase and so on. The problem continues beyond the transonic envelope,
since the centre of pressure continues to move rearward.
68. Since the condition of speed instability is inherently a very dangerous one, supersonic,
transonic and high-speed subsonic aircraft are fitted with a Mach trimming system.
69. The Mach trim is a fully automatic trimming device which is sensitive to Mach number, and
which moves the elevator/stabiliser to compensate for the pitching movements which are expected at
any given Mach number.
Lateral Stability
70. Shockwave formation does not usually occur at precisely the same Mach number and
location on each wing and consequently one wing starts to drop when MCRIT is exceeded due to the
reduction in lift it produces. Furthermore, laterally stationary design features (dihedral, sweepback)
which increase the lift of the downgoing wing in the sideslip produce a greater local acceleration of
the flow and this higher local Mach number may well cause further wing drag by creating a
shockwave or intensifying an already existing shockwave or that downgoing wing.
71. Any asymmetry in the formation of shock waves on the wings will result in a tendency for a
wing drop to occur between MCRIT and a MFS of 1.0.
Vortex Generators
72. These devices, which we have already met in previous chapters, are not only useful in limiting
spanwise flow to prevent tip stalling. It will be recalled that the boundary layer breaks away when it
is no longer able to overcome the adverse pressure gradient over the upper surface of the wing. The
formation of a shock wave makes matters worse since the speed of the boundary sub-layer is
subsonic so the high pressure at the wave can be transmitted forward.
73. As we know, the vortex generators are small plates projecting from the upper surface of the
wing and they create vortices that re-energise the boundary layer. In addition, they appear to weaken
the shock wave and so reduce shock drag. Shock buffet is reduced by the vortices they produce.
74. Other vortex inducing devices such as the saw tooth leading edge, the wing fence and the
notched leading edge achieve the same result. A thickened trailing edge is also sometimes used to
create vortices at the point where the boundary layer is thickest and most sluggish.
FIGURE 9-15
Supercritical Wing
76. The upper surface is relatively flat, whereas the lower surface has more pronounced
curvature. The airflow does not achieve the same increase of speed over the upper surface and
therefore the formation of a shock wave is delayed until a higher MFS. The critical drag Mach
number (MCD) is thus also increased.
77. If the upper surface leading edge is very carefully profiled then any expansion waves will
reflect from the supersonic/subsonic boundary back to the shock wave and reduce its intensity. The
principle is shown at Figure 9-16.
FIGURE 9-16
Effect of Leading
Edge Shape on
Shock Wave
Intensity
78. Some of the lost lift from the flattened upper surface is recovered by a pronounced reflex
camber near the lower surface trailing edge. The section is rear-loaded in its lift generation, and is
therefore often referred to as an aft-loaded wing.
79. The section profile is very critical, particularly the leading edge and the early part of the upper
surface. In order to keep the upper surface free of joints, any leading edge devices will be of the
Krueger type, which fold out from the under surface. Note the blunt leading edge.
80. The advantage of the supercritical wing is that high Mach number cruising speeds can be
maintained with a thicker (stronger) wing, which requires less sweepback.
82. The shock wave moves away from its source at the speed of sound. Imagine now a body
moving at greater than sonic speed along a straight path. As it travels the pressure wave it generates
is not only moving outwards from the body, but it is also being left behind. This is illustrated at
Figure 9-17.
FIGURE 9-17
Oblique Shock
Waves
83. From Figure 9-17 it can be seen that the shock wave produced is oblique to the direction of
travel of the source and it is consequently called an Oblique Shock Wave. The angle it makes with
the direction of travel is known as the Mach Angle. The higher the supersonic speed the shallower
the mach angle will be.
Mach Cone
84. If the shock source is a single point, such as the nose of a bullet, the shock pattern will be
three-dimensional and so the shock boundary will be cone-shaped. If the source is a straight line,
such as the leading edge of a wing, a wedge will be formed. In either case the angle at the apex will
be twice the mach angle.
Aircraft Weight
85. Buffet boundary and all reference speeds, such as MCRIT and maximum operating Mach
number (MMO), are absolutely dependent upon aircraft weight. Basically, the greater the weight, the
lower the reference speed because a greater angle of attack is needed for any given speed. This means
that, as fuel is burned off during flight and aircraft weight reduces, reference speeds gradually
increase permitting increased aerodynamic ceiling.
Expansion Waves
86. When a supersonic flow meets a convex corner it is free to expand, which results in a decrease
in pressure, density and temperature as the flow lines become further apart. At the same time the
velocity of the flow increases. These features are indicated in the diagram at Figure 9-18.
FIGURE 9-18
Expansion Wave
87. From Figure 9-18 it will be seen that, because of the velocity increase that takes place as the
air flows around the corner, the Mach number of the flow increases. Also, the angle between the new
Mach line and the direction of flow has become more acute. This is to be expected since, as we now
know, the higher the speed of the supersonic flow the more acute the mach angle.
88. It should be emphasised at this point that the Mach lines are not shock waves. Shock waves
are formed at a point where a number of mach lines converge, as would be the case when a
supersonic flow meets a concave corner, as at Figure 9-19.
FIGURE 9-19
Shock Wave
89. Mach lines are weak waves that may form at any point on a surface in a supersonic flow and
the flow passes through them without undergoing any sudden physical changes. When the
supersonic flow meets a concave corner as at Figure 9-19 the convergence of the Mach lines produces
a strong oblique shock wave, through which there is a sudden increase of pressure, temperature and
density and a decrease of velocity. This is known as compressive flow.
90. Conversely, the phenomenon occurring at a convex corner is called expansive flow and the
weak wave associated with it is known as an expansion wave. The changes in pressure, temperature
and density that occur at an expansion wave are relatively gradual, when compared to a compression
shock wave. In comparison with subsonic flow however, where changes begin well before the corner
is reached and continue well after it is passed, they are still relatively rapid.
91. It is possible to turn supersonic flow through a large angle by means of a series of expansion
waves created by a succession of convex corners. A curved surface is, of course, an infinite
succession of corners and over such a surface there will be a series of expansion waves. As
supersonic flow passes over the curved surface there will be a succession of expansion waves in
which the physical changes will be even more gradual than at a single corner.
92. The designer of the supersonic aircraft seeks to include convex curves in the design wherever
possible, since this will not only reduce the shock wave effects in supersonic flight, but is also
beneficial in subsonic flight.
Centre of Pressure
93. During transonic flight the centre of pressure moves progressively aft, typically from about
20% chord at Mach 0.75 to about 50% chord at Mach 1.4. In supersonic flight this rearward
migration of the centre of pressure continues and is one of the factors limiting the maximum Mach
number achievable with a swept wing planform.
94. By careful design it is possible to retard the rearward movement of the CP. In Concord, for
example, the aft movement of the CP is limited to about 8% of total chord, but this is still a
considerable distance and has to be counteracted by transference of fuel to move the centre of gravity
(CG) aft a corresponding amount.
Limitations
Operating Limitations
Control Reversal
Flap/Landing Gear Operation
Limiting Speeds
The Manoeuvring Envelope
The Gust Envelope
The Buffet Onset Boundary Chart
10 Limitations
Operating Limitations
1. Any aircraft is designed in the first instance to meet certain performance requirements in
terms of payload, operating speed, operating altitude and so on. The designer goes to great lengths
to ensure that there is adequate structural integrity to meet those design requirements and then
formulates the parameters within which the aircraft can safely be operated. In so doing he will
incorporate due allowance for unusual factors such as gusts due to rough air or turbulence, by
making the airframe structurally flexible.
2. The necessary flexibility of the structure can of itself cause control problems and, in extreme
cases, lead to structural failure.
Control Reversal
3. Control reversal is a problem that arises from the aerodynamic force overcoming torsional
stiffness and causing wing twist. When an aileron is deflected downwards it increases the lift
coefficient of the wing at that point. The increased lift is acting a point on the chord well to the rear
of the flexural centre and there is a tendency for the wing to twist. This is especially so with
outboard ailerons, located as they are at the point of least torsional stiffness.
4. The greater the airspeed the greater the lift produced by a downgoing aileron and so the
greater the wing twist, eventually to the extent that the overall angle of attack at the tip is negative –
the reverse of the intended effect! It is only likely to occur on aircraft not designed for high subsonic
or transonic flight when a limiting airspeed is exceeded.
6. Extending the landing gear considerably increases the profile drag of the aircraft and alters
the thrust/drag relationship. There is a limiting airspeed for landing gear extension to avoid
imposing excessive loads on the gear attachment points and to avoid possible pitch control problems.
Limiting Speeds
7. For every aircraft there are operating speeds designed to ensure that potentially hazardous
structural and control problems are never encountered.
VMO
This is the maximum operating speed and is normally expressed as IAS. It is the limiting speed at
low altitude because it will be achievable before limiting mach number in dense air. When
descending at constant mach number IAS will be increasing, and therefore VMO may be exceeded. It
is the maximum permitted speed for all operations.
VNO
This is the normal operating speed. It is the maximum permitted speed for normal operations.
VNE
This is the Never Exceed Speed. It is a higher maximum permitted speed when operationally
desirable.
MMO
The same as VMO, but quoted as a Mach number. It is the limiting speed at high altitude because it
will be achievable before limiting IAS in less dense air. When climbing at constant IAS the mach
number will be increasing, and therefore MMO could be exceeded.
VLO
This is the maximum speed at which the landing gear may be lowered or retracted.
VLE
This is the maximum speed with the landing gear extended. It may be the same as VLO or may be
different, depending on the design of the gear and doors. On some designs the doors are open whilst
the gear is moving and retract when the gear is locked down and in such cases it may be found that
VLE exceeds VLO.
VFE
This is the maximum speed for lowering flaps to various flap settings. It is possible to incorporate
automatic flap positioning and load-limiting devices based upon airspeed or dynamic load inputs to
ensure that the flaps cannot be overstressed.
9. The aeroplane must be constructed to withstand the loads to which it will be subjected during
normal operations. These are defined as the load factor, or g force, acting upon the aircraft. In
straight and level flight in calm air the load factor, or g force, is 1 because the lift (L) is equal to the
weight (W). From chapter four (Stalling) it will be recalled that:
L
n = -----
W
10. During manoeuvres the load factor (n) increases. Imagine the situation when, for example,
the aircraft is pulling out of a dive. In order to arrest the dive the angle of attack is increased and the
lift force acting upon the wings exceeds the aircraft weight during the period of pull-up, increasing
the loading on the wings.
11. The more abrupt the pull-up the greater the angle of attack and therefore the greater the wing
loading, or load factor n. Exactly the same is true during a tight turn or, for that matter, during any
manoeuvre. When manoeuvring, the lift and weight will not be equal. When lift exceeds weight the
load factor, or g acceleration is said to be positive, when weight exceeds lift the load factor is said to
be negative. The latter is the case during a bunt (or outside loop) manoeuvre or when making an
outside turn. So, in straight and level (non-manoeuvring) flight the load factor is +1.
12. As load factor increases the stalling speed increases and this establishes the first of the
manoeuvring operating limits.
13. From chapter four we know that the maximum lift at any airspeed occurs at maximum lift
coefficient (CLmax) and that maximum lift occurs at the stall. Therefore:
1 2
L max = C Lmax --- ρV m S
2
15. At the basic stalling speed (Vs) weight (W) must be equal to maximum lift (Lmax). Therefore:
1 2
W = CLmax --- ρV s S
2
16. Therefore:
1 2
C Lmax --- ρV m S Vm
2
L 2
n = ----- = ----------------------------------- = -------2-
W 1 2
CLmax --- ρV s S Vs
2
17. So:
Vm = Vs n
18. For example, the manoeuvring stall speed at a load factor of 2 for an aircraft with a basic
stalling speed (Vs) of 110 knots would be: Vm = 110 2 = 155 knots
19. At a load factor of 3 it would be 190.5 knots, at load factor 4, 220 knots and so on.
20. From this it is possible to plot the manoeuvring stall speeds against load factor on the
manoeuvring load diagram, or V – n diagram as it is sometimes known, as shown at Figure 10-1. It
will be noted from this that it is possible to fly at less than the basic stalling speed provided the load
factor is less than one. This is of course exactly what is happening when we see simulated
weightlessness during astronaut training, as the training aircraft flies a zero g bunt after initiating a
steep pitch angle climb.
FIGURE 10-1
Manoeuvre Stalling
Speed
21. The load factors to which an aircraft is designed to safely operate depends upon the role it is
to perform. Aeroplanes of large mass will, because of structural limitations, have lower limits than
smaller aeroplanes. The values are published in JAR 25 (large aeroplanes) and JAR 23 (normal,
utility, aerobatic, and commuter). They are as follows:
JAR 25
22. The positive limit manoeuvring load factor (‘n’) for any speed up to VD may not be less than
24000
2.1 + --------------------------- except than ‘n’ may not be less than 2.5 and need not be greater than 3.8 where W
W + 10000
is the design maximum take off weight (lbs).
(2) must vary linearly with speed from the value at VC to zero at VD.
Manoeuvring load factors lower than those specified may be used if the aeroplane has design features
that make it impossible to exceed these values in flight.
JAR 23
23. The positive limit manoeuvring load factor may not be less than:
24000
(1) 2.1 + --------------------------- for normal and commuter category except that ‘n’ need not
W + 10000
be more than 3.8
The negative limit manoeuvring load factor may not be less than:
(1) 0.4 times the positive load factor for the normal, utility, and commuter
categories or;
(2) 0.5 times the positive load factor for the aerobatic category.
Manoeuvring load factors lower than those specified may be used if the aeroplane has design features
that make it impossible to exceed these value in flight.
24. From this we can now add two more limits to the manoeuvring load diagram, the design
maximum positive and negative load factors. Beyond these load factors some structural damage or
deformation may occur.
25. If the maximum load factor, positive or negative is exceeded by more than 50% then
structural failure will occur, giving us a further two limits to add to the diagram, the design ultimate
positive and negative load factors. This is illustrated at Figure 10-2.
FIGURE 10-2
Manoeuvre Load
Factor Boundaries
26. Finally, every aircraft has a maximum operating speed that must not be exceeded. Adding
this vertical line to the manoeuvring load diagram completes the limits that form the Manoeuvring
Envelope, as shown at Figure 10-3.
FIGURE 10-3
Manoeuvre Speed
Limit
27. Figure 10-4 shows the manoeuvre envelope for a complete aeroplane in the large category.
Note that the stall buffet boundary (CN MAX) with flaps down has been added. Also shown are
significant speeds.
FIGURE 10-4
Manoeuvre
Envelope
VC is the design cruising speed. At altitudes where VD is limited by mach number, VC may be limited
to a selected mach number.
VA is the design manoeuvring speed. It is the highest speed at which the aeroplane will stall before
exceeding the maximum load factor. Its maximum value may be calculated by multiplying VS1 by the
square-root of the maximum load factor. As aeroplane mass reduces VA will reduce as VS1 reduces.
Given VS1 160 kts. Load factor limit +2.5. Calculate VA.
Given VS1 160 kts. Load factor limit +2.5. VA 253 kts. Weight 8000 kgs. Calculate VA at weight
6500 kgs.
6500
New V S = 160 × ------------ = 144kts
8000
28. The load placed upon the aircraft structure during flight is dependent upon aircraft weight
and the manoeuvring load diagram is based upon a particular design gross weight. If the aircraft is
operated at a higher gross weight the load factor for any given airspeed will be greater. In other
words, the maximum load limit will be encountered at a lower airspeed.
29. It will be noted that the airspeed used for the design case is EAS, whereas at altitude the pilot
is usually much more concerned with TAS. Since the relationship between the two airspeeds is
relative air density, at altitude any given value of TAS is equivalent to a much lower value of EAS.
The design EAS values of VA, VC and VD are reduced for altitudes above 20,000 feet, usually as a
step reduction.
30. As altitude is increased the TAS/EAS at which MCRIT is encountered decreases to a value less
than VD, modifying the manoeuvring envelope. For aircraft designed to operate in the high subsonic
or transonic regime a complete envelope will show Mach number limits for each altitude.
32. During flight in rough air the aircraft will encounter gusts which will place loads upon the
aircraft structure. It is the vertical component of any gust that is important in terms of load factor,
since a vertical gust increases the effective angle of attack and therefore the magnitude of the lift
generated. This, of course, increases the loading on the wings. The situation is illustrated at
Figure 10-5.
FIGURE 10-5
Effect of Vertical
Gust
33. In determining the load factor that will result from an aeroplane encountering a vertical gust
the designer must decide upon two factors, the speed of the aeroplane and the vertical speed of the
gust. He therefore chooses a design speed at which he expects the aircraft to operate in normal
circumstances (VB), and applies a vertical gust velocity based upon many years of recorded values.
This arbitrary gust speed is 66 feet per second.
34. Were the aircraft to encounter a gust when flying at a higher speed, clearly the resultant load
factor would be greater so the designer must allow for this also. However, the mathematical
probability of this happening is less and so the arbitrary gust velocities applied are lower. At the
design cruise speed (VC) the assumed gust value is 50 feet per second and at the design dive speed
(VD) it is 25 feet per second. If these values are plotted on a load, or V – n diagram as shown at
Figure 10-6, a gust load diagram is the result. VB will be less than VD and need not be greater than
VC.
FIGURE 10-6
Gust Envelope
35. The arbitrary vertical gust velocities are plotted from the load factor 1 point on the vertical
axis of the graph, since this is the load factor in straight and level flight in smooth air. Where they
intersect the chosen aircraft velocities the load limits are established. Joining these points sets the
Gust Envelope within which the aircraft must operate in order to avoid stalling or exceeding the
limiting load factor.
36. It should be noted that the gradient of the positive stall curve is shallower than in the case of
the manoeuvring envelope. This is because a vertical gust, by increasing the effective angle of attack,
increases the airspeed at which the stalling angle is reached.
37. From the gust load diagram another important reference airspeed is established, the
recommended speed for flight in turbulence, or rough air speed (VRA). VRA must lie within the range
of speeds for which the requirements associated with VB are met and must be sufficiently less than
VMO to ensure that likely speed variations in rough air will not cause the overspeed warning to
operate too frequently.
38. As with the manoeuvring envelope, the effects of aircraft gross weight, altitude and Mach
number must be taken into account in the case of the gust envelope. The gust load diagram is drawn
up for particular values of each and the complete envelope will show the effects of flight at varying
altitudes and gross weights. In addition, wing aspect ratio and sweepback must be considered since a
high aspect ratio will generally be less resistant to bending loads.
40. Buffet is vibration of the airframe which, if excessive and prolonged, could cause structural
damage, interfere with control of the aeroplane, and may result in excessive crew fatigue. Whilst in
the cruise, buffet may be experienced for two reasons. At low speed it will be felt just prior to the
aeroplane stalling, known as the pre-stall buffet, which occurs at approximately 1.2 VS. When
approaching the maximum speed limit the high speed buffet will be experienced, due to shock-
induced separation (see chapter on high speed flight). Except for low-speed stall warning buffet,
there should be no perceptible buffet at any speed up to VMO/MMO (JAR 25.251(d)).
41. The speed range available at which to cruise is, therefore, between 1.2 VS and VMO/MMO,
and this speed range will decrease as altitude is increased. When this speed range has reduced to zero
the aeroplane is at its aerodynamic ceiling (not to be confused with the service ceiling, which is
dicated by power available). Although a low-speed stall warning is fitted, it is unlikely that the pilot
would allow the speed of the aeroplane to fall to this speed inadvertently. However, it is possible to
inadvertently exceed VMO/MMO and encounter the high-speed buffet. This increase in speed may be
caused by gust upsets, uninentional control movement, or when levelling off from a climb or descent
from mach to airspeed limit values such as during an emergency descent. For such an eventuality a
high-speed aural warning device is fitted to most aeroplanes and in addition a maximum speed
needle on the airspeed indicator shows VMO up to the altitude at which VMO = MMO where the
datum becomes MMO. The warning will sound at approximately 10kts above VMO or 0.01M above
MMO.
42. For normal operations it is possible to construct a graph against altitude to produce an
envelope within which it is safe to operate in the cruise which is limited by the buffet onset. Such a
Buffet Onset Boundary Chart is shown at Figure 10-7.
43. The lower limit is defined by the pre-stall buffet and the upper limit by VMO/MMO. This
should produce a sufficient range of speeds and load factors for normal operations. Inadvertent
excursions beyond the boundaries of the buffet envelope will not result in unsafe conditions without
prior adequate warning to the pilot (JAR 25.251(c)).
44. Although the maximum limit of the buffet boundary is fixed for all weights, the lower limit
increases with increased weight. Therefore the range of speeds available for normal operations
increases as the weight reduces with fuel burn. For any given weight, centre of gravity position and
airspeed the maximum operating altitude is that at which it is possible to achieve a positive normal
acceleration increment of 0.3g without exceeding the buffet onset boundary (ACJ 25.1585(c)). It is
therefore common practice to draw the buffet onset chart for 1.3g. The intersection of the pre-stall
buffet and VMO/MMO lines defines the ‘aerodynamic ceiling’ (JAR 25.251(e)2). It follows then that
as altitude increases manoeuvrability becomes increasingly restricted. In good weather this is of little
consequence apart from encountering clear air turbulence but in bad weather it has great significance
because of the possibility of turbulence disturbing thte ‘status quo’ and requiring correction which
becomes increasingly more difficult as altitude increases. Operating areas near the limits are often
referred to as ‘coffin corner’.
EXAMPLE 10-1
EXAMPLE
Using Figure 10-7. Given:
Airspeed - M0.72
Altitude - 35,000ft
Gross weight - 50,000 kg
C of G - 10% MAC
Find: Low and high speed buffet for 1g flight.
Manoeuvre margin to initial buffet (load factor and bank angle).
SOLUTION
Enter graph with mach number (A)
Move up to altitude line (B)
Move across to reference line (C)
Follow %MAC line to 10% (D)
Move across to weight line (E)
Move vertically down to find load factor and bank angle for initial buffet.
= 1.47g and 47 degrees of bank
FIGURE 10-7
Buffet Onset
Boundary Chart
EXAMPLE 10-2
EXAMPLE
Using Figure 10-8.
Given:
Load factor - 1.3g
Gross weight - 59,000 kg
C of G - 10% MAC
SOLUTION
Enter graph with load factor (A)
Move up to gross weight (B)
Move across to %MAC and back to reference line (C)
Move across to intercept peak of altitude line (D)
= 34,000ft.
FIGURE 10-8
Buffet Onset
Boundary Chart
QUESTIONS:
QUESTION 1.
To ensure positive longitudinal stability, will the centre of pressure be ahead or behind the centre of
gravity?
QUESTION 2.
QUESTION 3.
QUESTION 4.
QUESTION 5.
QUESTION 6.
In terms of stability, how would you describe an object which is oscillating with increasing
amplitude?
QUESTION 7.
QUESTION 8.
QUESTION 9.
QUESTION 10.
QUESTION 11.
QUESTION 12.
QUESTION 13.
QUESTION 14.
QUESTION 15.
QUESTION 16.
QUESTION 17.
Refer to the cruise manoeuvre capability chart supplied at Figure 40 in the Reference Book. Given
the following information, find the low and high speed buffet for 1g flight, and the bank angle to
initial buffet:
airspeed M0.76
altitude 36,000ft
C of G 10% MAC
QUESTION 18.
Using the chart at Figure 40 in the Reference Book and given the following information, find the
aerodynamic ceiling:
C of G 20% MAC
ANSWERS:
ANSWER 1.
Behind
Chap 8 page 4
ANSWER 2.
The distance through which the C of G can be moved aft from the datum to the neutral point
Chap 9 page 5
ANSWER 3.
Greater
Chap 8 page 8
ANSWER 4.
Sideslip due to uncommanded roll results in the lower wing having a higher aspect ratio and thus
higher lift coefficient
Chap 8 page 26
ANSWER 5.
Reduce it
Chap 8 page 27
ANSWER 6.
Dynamically unstable
Chap 8 page 29
ANSWER 7.
Chap 8 page 31
ANSWER 8.
Chap 8 page 32
ANSWER 9.
Reduces
Chap 8 page 33
ANSWER 10.
Chap 9 page 5
ANSWER 11.
Chap 9 page 5
ANSWER 12.
Chap 9 page 5
ANSWER 13.
ANSWER 14.
Aft movement of the centre of pressure as the shockwave moves aft with increasing transonic speed
Chap 9 page 17
ANSWER 15.
Chap 9 page 21
ANSWER 16.
Chap 10 page 13
ANSWER 17.
ANSWER 18.
33,000ft
Special Circumstances
11 Special Circumstances
1. It has been shown in previous chapters that the performance of the boundary layer is
fundamental to the lift coefficient of the wings and other lifting surfaces. Clearly anything which
modifies the lifting surfaces in a manner detrimental to the boundary layer will reduce the lift
coefficient.
3. The aerodynamic shape of the blade will change and result in a reduction in its capability to
convert the power from the engine into thrust. In addition to the reduction in thrust, there will also
be an increase in drag due to the relatively rough nature of the ice causing an increase in skin friction.
4. The increase in weight and its distribution can lead to increased loading and out of balance
vibration and should the ice adhering to the blade now come free, damage to the airframe and/or
engine can ensue.
5. Furthermore, the pitch change mechanism of a variable pitch propeller can be affected by the
formation of ice and hence a reduction in efficiency, which will already have been reduced by a
reduction in the thrust produced.
7. Heavy rain may cause standing water on the runway to such a depth that take-off
acceleration may be affected and engine ingestion of water from tyre spray may be a hazard.
Standing water also increases the danger of aquaplaning by the wheel tyres, especially during
landing.
Loss of Controllability
8. Any reduction of boundary layer energy reduces the aircraft speed at which the adverse
pressure gradient will cause boundary layer separation and therefore increases the stalling speed and
reduces the stalling angle of attack. This in turn means that use of the ailerons at low speeds or high
angles of attack is more likely to lead to tip stall and loss of lateral control. Similarly, high rates of
turn are more likely to lead to manoeuvring stall, because of the higher effective angle of attack
necessary during the turn. Clearly, ice or frost contamination of the elevator and rudder surfaces
increases the likelihood of their stalling when large control demands are made, as may be necessary
during flight at low speed.
9. The control surfaces move about a fulcrum, which is not usually coincident with the centre of
pressure of the control. Hence there is an aerodynamic moment, which must be balanced by the
input force from the pilot’s controls. The changed aerodynamic characteristics due to ice or frost
formation on the control surfaces may significantly alter the aerodynamic moment. This, in turn,
means that the force required to move the surfaces would be altered.
11. Leading edge ice formation on the flaps themselves is particularly detrimental in the case of
slotted flaps, since the airflow through the slots may be affected. The consequent loss of the re-
energising effect on the boundary layer results in loss of lift and an increase in drag. The effect on the
take-off will be to increase the length of the take-off run and on landing to increase the landing speed
and landing distance required.
12. Surface frost or ice on leading or trailing edge flaps will have the same effect as on the wing
surface, encouraging boundary layer separation and increasing drag. This will reduce the
effectiveness of the high lift devices.
14. Furthermore, as aircraft grow older they are often repainted in new liveries with only partial
removal, if any, of the old. This can add considerably to the overall weight of the aircraft with a
consequent reduction in performance from that advertised.
Windshear
16. Windshear is caused by variations in the direction and/or speed of the local wind with
changes in height and/or horizontal distance. It is almost always present but normally does not cause
undue difficulty in controlling an aeroplane. It is abnormal windshear which is dangerous, and tends
to displace an aeroplane abruptly from its intended flight profile such that substantial control input is
required. A full explanation of the causes may be found in the Meteorology notes.
Effects of Windshear
Energy Loss
17. An aircraft encountering windshear tends to maintain its speed over the ground due to its
own momentum (the larger the aircraft the more momentum it will have). If the windshear is due to
a reduction in headwind component (or increase in tailwind component) this reduction manifests
itself as an energy loss and a reduction in indicated airspeed. Lift is therefor reduced and the aircraft
will, without correction, suffer a loss of height/increase in rate of descent/decrease in rate of climb.
The situation is shown at Figure 11-1.
FIGURE 11-1
Effect of
Reduction in
Headwind
Component
Energy Gain
18. An increase in headwind component (or decrease in tailwind component) results in an energy
gain and increase in indicated airspeed, as shown at Figure 11-2.
FIGURE 11-2
Effect of Increase
in Headwind
Component
19. These events become critical when the aircraft is being flown close to the ground during the
final stages of an approach or shortly after take-off. In the energy loss case the engine reaction time
when additional thrust is demanded can be critical.
20. The energy gain/loss situations described above can occur as a result of either vertical
windshear or as horizontal windshear, in other words the aircraft can either climb/descend or fly
horizontally into air flowing at a different speed or from a different direction, in either event
changing the head/tail wind component. In simple terms a change in the wind component will, in the
short term, change the airspeed rather than the groundspeed of the aircraft.
Downdraught
21. Figure 11-3 shows an aircraft taking off in the vicinity of a thunderstorm.
FIGURE 11-3
Effect of
Downdraught on
Take-off
22. The situation illustrated is the critical case where the headwind component decreases sharply
and/or becomes a tailwind component shortly after take-off (energy loss). In this case, because of
inertia, the groundspeed remains constant but the airspeed decreases sharply. The loss of lift
associated with the resulting low airspeed may cause the aircraft to strike the ground.
FIGURE 11-4
Effect of
Thunderstorm on
the Approach to
Land
24. Initially, at position A, the aircraft is stabilised on the glideslope maintaining target airspeed.
Suddenly the aircraft flies through a gust front into the cold air which is spilling from the base of the
cloud. What was a slight tailwind component is now a very marked headwind component but,
because of inertia, the groundspeed will momentarily remain constant. The result is that the airspeed
is increased by an amount equal to the change in wind component. The amount of lift generated will
increase with the increased airspeed, and the aircraft will initially make a rapid excursion above the
desired glideslope at point B. The natural reaction of the pilot in this situation is to reduce thrust and
steepen the approach. Now, the increased headwind component will give a lower groundspeed once
the effect of inertia has been overcome, and this will require an increase in thrust and a decreased
rate of descent.In other words the pilot’s initial response is 100% incorrect, and the aircraft is now
descending rapidly in an underpowered configuration to point C and a go-around must be initiated.
26. If downbursts are encountered near thunderstorms, then the recommended actions during
approach or take-off phases are:
(b) Adopt a pitch angle of about 15 degrees and hold that attitude. Do not chase airspeed.
(c) Be guided by stick-shaker indications when holding or increasing pitch attitude, easing
the back pressure as required to attain and hold a slightly lower attitude.
27. It is difficult to be specific on the use of autopilots, autothrottles and flight directors, but in a
severe encounter it may be best to revert to manual handling.
Propellers
Propeller principles
Power Absorption
Fixed Pitch Propellers
Variable Pitch Propellers
Propeller Effects
Propeller Forces and Moments
12 Propellers
1. The aircraft propeller is a device for converting the shaft power of a piston engine or gas
turbine into thrust power. It functions by imparting a relatively small velocity increase to a relatively
large mass of air.
Propeller principles
2. The aircraft propeller comprises a number of blades mounted upon a central shaft, rotating
about an axis that is parallel to the direction of required thrust, i.e. the direction of flight. The
rotating propeller blades form a disc that is perpendicular to the direction of thrust. Figure 12-1
shows the propeller disc of a four-bladed propeller.
FIGURE 12-1
Propeller Disc
Blade Angles
3. Each propeller blade has an aerofoil section similar to that of a wing as shown at Figure 12-2.
FIGURE 12-2
Propeller Blade
Terminology
4. Because the blade section of a propeller is an aerofoil section similar to that of a wing, it
generates lift as it rotates in rather the same way as a wing creates lift.
5. When the aircraft is stationary in still air conditions, with the propeller rotating, the airflow
relative to the propeller blades is parallel to the plane of rotation. Under these circumstances the
propeller blade angle or geometric pitch angle, which is the angle between the plane of rotation and
the chord line of the aerofoil and the angle of attack, are the same thing. When the aircraft is moving
forward however, there is a forward velocity vector in addition to the rotational velocity and their
resultant is the path of the blade element which of course determines the airflow relative to the
propeller blade.
6. The angle between the plane of rotation and the relative airflow is referred to as the helix
angle, or angle of advance, and thus:
FIGURE 12-3
Angle of Attack
7. The geometric pitch is the distance that a propeller should advance in one complete
revolution. A useful analogy is the distance that a wood screw would advance into a piece of timber
in one complete revolution. The effective pitch is the distance that the propeller actually advances in
one revolution. The difference between the two is known as propeller slip. The principle is
illustrated at Figure 12-4. Because air is not a perfect propulsion medium propeller slip is inevitable
and it accounts for a significant energy loss in the conversion of torque to thrust.
FIGURE 12-4
Propeller Slip
FIGURE 12-5
Forces on a
Propeller Blade
Element (Section)
9. Note from Figure 12-5 that the better the lift/drag ratio the further forward is the total
reaction vector, and consequently the greater the amount of engine power that is translated into
thrust, whereas propeller torque acts in the plane of rotation and opposes engine torque, ie. it is the
resistance to rotary motion and as such is an undesirable force vector since it is trying to rotate the
aircraft in the opposite direction to that of the propeller rotation.
Blade Twist
10. It can be seem from Figure 12-3 that the angle of attack is governed by the relationship
between the propeller's rotational velocity and the aircraft's forward speed. For the best lift/drag
ratio, the most desirable propeller angle of attack lies between 2° and 4°. At angles of attack greater
than 15°, the blades will stall and the propeller will become ineffective.
11. Clearly, the rotational velocity of the propeller blade is greater at the tip than at the root and
consequently, the rotational velocity depends upon the point on the blade radius where the rotational
velocity is considered. Since the rotational velocity is one of the vectors that determine the direction
of the relative airflow, and therefore the blade angle of attack, the blade is twisted to maintain a
constant angle of attack along its entire length. Blade twist is illustrated at Figure 12-6.
FIGURE 12-6
Blade Twist
Propeller Efficiency
12. The mechanical efficiency of any system is the ratio of power out to power in.
13. The force rotating the propeller is the torque, or twisting force developed by the engine and
delivered to the propeller shaft. The power delivered to the propeller is the product of this twisting
force, or torque, and the angular velocity of the propeller shaft.
14. The force exerted by the propeller is the product of the mass of air moved and the
acceleration given it by the propeller. This force is called thrust. The power developed by the
propeller is the product of thrust and the true airspeed (TAS) of the aircraft.
Thrust x TAS
Propeller Efficiency (η ) = ---------------------------------
Torque x 2N
FIGURE 12-7
Effect of Speed on
a Fixed Pitch
Propeller
16. At low forward speed the angle of attack is high and, although the blade will be producing a
large amount of thrust there will also be high drag. The forward speed (TAS) is low, and the torque
required to maintain propeller rpm is high in order to overcome the high drag. Since:
Thrust x TAS
Propeller Efficiency (η ) = ---------------------------------
Torque x 2N
17. It can be seen that propeller efficiency will be low under these circumstances.
18. At high forward speed the angle of attack is reducing to the incidence at which no lift is
generated, which means that the thrust element of the efficiency equation is low and therefore
propeller efficiency will be low.
Power Absorption
19. The amount of engine power that the propeller is able to absorb and convert into thrust
depends upon the lift-producing capability of the blades. As with a wing, the greater the aspect ratio
the greater the lift generated and aspect ratio is the ratio of span to mean chord. In the case of a
propeller blade it is the ratio of blade length to mean blade chord, so increasing propeller diameter
increases aspect ratio.
20. However, the greater the propeller diameter the higher the tip speed for any given rpm, so that
the tips reach sonic velocity at relatively low rpm. The compressibility effects at sonic velocity have a
very detrimental effect upon propeller efficiency, since the thrust is considerably reduced and the
blade drag (torque required) increased. Hence there is an aerodynamic limit on the practical
propeller diameter and upon the TAS at which a large diameter propeller can be used.
21. Another reason for avoiding sonic velocities at the blade tips is the unacceptably high noise
levels produced which, apart from environmental considerations, can have damaging fatigue effects
upon the aircraft structure.
Propeller Solidity
22. The usual way in which the power absorption ability of the propeller is increased is to
increase what is called the ‘solidity’ of the propeller disc. The solidity at any point on the radius of
the propeller disc is the ratio of total blade chord at that radius to total circumference at that radius.
The radius normally used for the calculation is 70% tip radius. The concept of solidity is shown at
Figure 12-8.
FIGURE 12-8
Propeller Solidity
23. From the above it can be seen that the solidity of the propeller disc can be increased either by
increasing the number of blades or by increasing the blade chord.
24. There is a practical limit to the number of blades that can be used, partly due to aerodynamic
interference between blades and partly due to the complexity of the pitch control mechanism, which
must be contained within the propeller hub. However, developments in both blade and pitch control
technology in recent years have made six and more blades possible when, up until the early 1980’s,
five blades was generally considered to be the limit.
25. Increasing the blade chord, to produce the paddle blade seen on most C-130 Hercules
transport aircraft, has the disadvantage of low aspect ratio but was considered the best choice at the
time for use with a high rpm power plant.
27. If a small blade angle, or fine pitch, is used the propeller will be at its most efficient at low
forward speeds. Thus it will be ideal for take-off and low flight speeds, but incapable of operating
efficiently at high TAS.
28. Conversely, if a large blade angle, or coarse pitch, is chosen the propeller will be inefficient
and will demand excessively high torque during take-off, but will be suitable for high flight speeds.
29. Examination of Figure 12-3 will show that the blade angle of attack could be adjusted by
varying the rotational velocity (propeller rpm), but this is a very limited option, especially with a
piston engine powered aircraft. By far the better solution is to operate at constant rpm and alter the
blade angle to produce an angle of attack to suit the forward speed of the aircraft; fine pitch for take-
off and landing and progressively coarser pitch for progressively higher TAS. This is illustrated at
Figure 12-9.
FIGURE 12-9
Effect of Speed on
.
Angle of Attack
31. This is shown at Figure 12-10 which compares the efficiency of a two-pitch propeller and a
variable pitch propeller with varying airspeeds.
FIGURE 12-10
Propeller
Efficiency
32. Reference to the propeller efficiency equation will show that efficiency increases with
increasing TAS. However there is a limit to this because there is clearly a finite limit to the extent to
which the blade angle can be increased and still produce a forward component of thrust. At about
300-350 knots TAS the blade angle is at its greatest practical value and any further increase in
airspeed will result in a reduction of thrust, so propeller efficiency begins to fall. This is illustrated at
Figure 12-11, which compares the efficiency of various forms of propulsion against airspeed.
FIGURE 12-11
Propulsive
Efficiency
Comparison
33. Deformation of the aerofoil section of the propeller blade will alter the thrust developed at
any airspeed. Whilst propeller blades are susceptible to deformation due to stones, bird strike and
other foreign object damage by far the greatest risk of deformation is from propeller icing. The
accretion of ice on the blades will significantly change their aerodynamic characteristics and
drastically reduce the thrust produced and propeller efficiency at any given airspeed and propeller
rpm. Most propeller-powered aircraft are equipped with some form of propeller anti-icing or de-
icing.
Propeller Effects
Torque Effect
34. Newton’s third law tells us that to every action there is an equal and opposite reaction. The
force rotating the propeller is torque so it follows that there must be a reaction force in the opposite
direction of rotation. In a single engine aircraft this torque reaction is attempting to rotate the
aircraft about the propeller shaft axis. This can create a rolling (and secondary yawing) tendency,
especially at take-off.
35. Torque effect can be eliminated by mounting two propellers, one behind the other, each
driven by its own shaft but in opposite directions. The shafts are concentric and as the propellers
rotate in opposite directions, their torque effects cancel each other out. Such an arrangement is
referred to as counter-rotating propellers.
36. Contra-rotating propellers, on the other hand, are two propellers mounted in tandem but
driven by a single engine through a gearbox to ensure the propellers rotate in opposite directions and
likewise their torque effects are cancelled out.
Slipstream Effect
37. An asymmetric slipstream effect occurs with single engine aircraft, and is illustrated at Figure
12-12. The slipstream corkscrews around the fuselage and strikes the fin predominantly on one side,
creating a yawing moment. The propeller shown at Figure 12-12 is a right hand tractor propeller (it
rotates in a clockwise direction when viewed from behind), and the yaw produced would be to the
left. This can be compensated for by mounting the fin at a slight angle to the aircraft centre line, or
by the application of right rudder, especially at high power settings.
FIGURE 12-12
Slipstream Effect
39. The essence of asymmetric blade effect is that the down going blade has a greater angle of
attack than the up going blade, and therefore generates more lift (thrust) than the up going blade.
This is shown at Figure 12-18.
FIGURE 12-13
Asymmetric Blade
Effect
40. Asymmetric blade effect is further exacerbated by the fact that the down going blade travels
further (in relation to the direction of travel of the entire aircraft) than the up going blade. Since it
does so in the same time, its relative speed is higher and thus its aerodynamic force higher.
Figure 12-14 illustrates this phenomenon.
FIGURE 12-14
Asymmetric Blade
Effect
Gyroscope Effect
41. Since the rotating propeller displays certain of the characteristics of a gyroscope, whenever a
force is effectively applied to the propeller, a precessed force will result which is transposed through
90° in the direction of rotation of the propeller.
42. If a tail wheel aircraft with a right hand tractor propeller is accelerating for take-off, the act of
raising the tail will be as if a force was applied downwards onto the propeller hub. This applied
force will be precessed 90° clockwise (when viewed from behind) and will cause a yaw to the left.
Conversely, when either a nose- or tail-wheeled aircraft with a right hand tractor propeller rotates
into the climbing attitude, gyroscopic effect will cause a yaw to the right. Similarly, yaw will be
precessed to produce a pitching moment.
FIGURE 12-15
Forces Acting on a
Rotating Propeller
44. In addition, variable pitch propellers have further forces acting upon them which create
twisting moments about their pitch change axis, thus altering the blade angle.
FIGURE 12-16
Aerodynamic
Twisting Moment
47. The radial components tend to stretch the blade whereas the tangential components produce
a twising moment about the pitch change axis. This centrifugal twisting moment tends to reduce the
blade angle (fine of the blade) as shown at Figure 12-7, and it is always greater than ATM.
FIGURE 12-17
Centrifugal
Twisting Moment
Engine Failure
48. In the event of engine failure, or the need to shut down an engine, the torque driving the
propeller is clearly lost. In the case of the constant speed (variable pitch) propeller, the propeller
speed governor will drive the blades to fine pitch in an attempt to maintain rpm. The aircraft still has
forward speed however, either due to the glide or the thrust from its remaining propellers. The
airflow relative to the blades of the unpowered propeller will now be at a negative angle of attack,
producing torque to rotate the propeller in the normal direction of rotation. The force component
perpendicular to the plane of rotation now acts rearwards and is therefore no longer thrust, but drag.
This is illustrated at Figure 12-18.
FIGURE 12-18
Forces on a
Windmilling
Propeller
Windmilling
49. The rotating blades at fine pitch present almost a flat disc at right angles to the flight direction
and therefore very high drag forces are present. Because the propeller is behaving exactly like a
windmill in the wind, this is known as windmilling drag.
50. In a twin-engine aircraft a windmilling propeller leads to asymmetric forces which can render
the aeroplane uncontrollable. In order to maintain flight speed above stalling the pilot is obliged to
increase power on the ‘good’ engine. The increased thrust from this, coupled with the drag of the
windmilling propeller, can produce a yawing moment too great for the rudder to compensate,
especially at low airspeed.
51. Additionally, the windmilling propeller driving a damaged engine may lead to overheating
and seizure.
52. Note also, that the total reaction force now produces a twisting moment about the pitch
change axis which tends to reduce the blade angle ie. both CTM and ATM will fine off the blade, as
shown at Figure 12-19.
FIGURE 12-19
Twisting Moments
on a Windmilling
Propeller
Propeller Feathering
53. To prevent the propeller from windmilling in the event of loss of engine torque the pitch
control mechanism usually incorporates a feathering facility. When the propeller is feathered the
blade angle is increased until the angle of attack is 0° and the blade angle is approaching 90°. With
the blades thus ‘edge on’ to the airflow there is no lift force to produce a torque reaction and the
propeller is not rotated. In practice, because the aerofoil section of a propeller blade is cambered, the
zero lift, or feathering blade angle is typically about 85°=as shown at Figure 12-20.
FIGURE 12-20
Feathered
Propeller Blade
54. With the propeller blades feathered the propeller is no longer presenting a disc to the airflow
and the drag is very significantly reduced when compared to that of a windmilling propeller. This
has a very beneficial effect on the glide performance of the aircraft since the greater the drag the
steeper the glide angle necessary to maintain airspeed.
55. Similarly, the relatively low drag of a feathered propeller reduces the yawing moment, even
with high power on the remaining engine, leaving sufficient rudder authority to control the aircraft in
yaw.
Reverse Thrust
56. In order to provide aerodynamic braking from the propeller during the landing roll, the blade
is turned until a negative blade angle is achieved which, when power is applied, will produce thrust
acting in the opposite direction to that normally produced by the propeller. This is shown at
Figure 12-21.
FIGURE 12-21
Reverse Thrust
57. The blade angle in reverse is restricted by the blade twist effect now also becoming reversed.
The blade tip is at a greater angle than the root when reverse pitch is selected and thus the thrust is
greatest at the tip. This creates a significant bending moment and limits the amount of reverse thrust
which the propeller can tolerate. Typically, in reverse the blade angle is limited to about -25°.
QUESTIONS:
QUESTION 1.
With regard to windshear, what do you understand by “energy loss”. What causes it and what are
the indications?
QUESTION 2.
QUESTION 3.
QUESTION 4.
QUESTION 5.
When a propeller is being driven by the engine, in which direction does propeller torque act?
QUESTION 6.
QUESTION 7.
With regard to a fixed-pitch propeller, what will happen to angle of attack as forward speed
increases?
QUESTION 8.
QUESTION 9.
QUESTION 10.
QUESTION 11.
QUESTION 12.
QUESTION 13.
QUESTION 14.
QUESTION 15.
ANSWERS:
ANSWER 1.
Chapter 11 Page 4
ANSWER 2.
The angle between blade chord line and the place of rotation. Otherwise known as geometric pitch
angle.
Chapter 12 Page 2
ANSWER 3.
The difference between blade angle and angle of attack. Otherwise known as angle of advance.
Chapter 12 Page 2
ANSWER 4.
Chap 12 Page 3
ANSWER 5.
Chap 12 Page 4
ANSWER 6.
To try to maintain constant angle of attack at all points along the blade.
Chap 12 Page 4
ANSWER 7.
Reduce
Chap 12 Page 6
ANSWER 8.
Optimum efficiency can be maintained over a wider range of forward speeds and propeller rpm.
Chap 12 Page 9
ANSWER 9.
The reaction of a rotating propeller will try to rotate the engine in the opposite direction to the
propeller.
Chap 12 Page 10
ANSWER 10.
One which is mounted forward of the pilot and rotates clockwise when viewed from behind.
Chap 12 Page 11
ANSWER 11.
A downgoing blade will generate more lift (thrust) than an upgoing are due to higher angle of attack
and higher relative speed.
Chap 12 Page 12
ANSWER 12.
At lower speeds and therefore, when the aeroplane is flying at higher angle of attack. Under such
conditions the angle between the propeller phase of rotation and the forward flight path vector in
greater.
ANSWER 13.
Chap 12 Page 15
ANSWER 14.
Chap 12 Page 17
ANSWER 15.
There is no propeller torque causing any rotation. The only force generated is drag (of low value).
Chap 12 Page 18