Professional Documents
Culture Documents
Electric Actuator
Electric Actuator
High preformance
brushless motor
Precision machining
technology
Electric Actuator
Delicate appearance
extremly long life span
Industrial grade component Precise transmission
MTD 01 Actuator
Selection Guide
Made in china Global service
Actuator selection guide
C ONTENTS
Failsafe series…………………………………………………………………………………… 9
Appendix
Actuator Appearance Dimension ………………………………………………………… 19
Actuator Assembly Diagram ……………………………………………………………… 20
Product overview
Purchase guide
2 3
Model Torque Voltage Wiring Feedback Time Speed Rotation Enclosure Manual Position Housing Output
regulation angle override indicator material shaft
Notice *1. Service life testing condition:The result is measured under rated load,test circle (2 times of switching time),at 25℃ working temperature and 50%
humidity which will be influenced by different load and working environment.
*2. S type is passive contact feedback,P type is active feedback,while R type is potentiometer feedback,SR type needs to be customized.
*3. F type is available in the ambient of high humidity(≥90%) but without long-term rain.
Purchase guide
2 3
Model Torque Voltage Wiring Feedback Time Speed Rotation Enclosure Manual Position Housing Output
regulation angle override indicator material shaft
IP67 Female
B2/B3 S Type 90°/300° Hexagon Mechanical PC+PET octagon
MTD-01NH 10Nm DC24V 2S None or spanner indicator or
/BD3 ≤330° F Type male square
Purchase guide
2 3
Model Torque Voltage Wiring Feedback Time Speed Rotation Enclosure Manual Position Housing Output
regulation angle override indicator material shaft
Notice *1. Service life testing condition:The result is measured under rated load,test circle (2 times of switching time),at 25℃ working temperature and 50%
humidity which will be influenced by different load and working environment.
*2. S type is passive contact feedback,P type is active feedback,while R type is potentiometer feedback,SR type needs to be customized.
*3. F type is available in the ambient of high humidity(≥90%) but without long-term rain.
Product overview
◎ Matched valves: 2-way, 3-way ball valve and butterfly valve
◎ Rated voltage: AC/DC95V-265V,AC/DC24V
◎ Control feedback mode: BD3J,B3J,B33J,B43J(feedback synchronous with arrival)
◎ Alarm output: A(Relay contact feedback)
◎ Achievable mode: 2 way /3 way 1
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show valve opening angle and external control command.Enter sleeping state automatically after about 5 minutes,it could
display location state and its control command during sleeping time.
△ Original valve adjustment mode:cover-opening and interactive
step1:Press the button to control valve to the position of “counterclockwise full open”, then save it .
step2:Press the button to control valve to the position of “clockwise full close” ,then save it to finish the valve adjustment.
Thoroughly eliminate the complex and inconvenient factors caused by mechanical positioning.
△ 16 bits high performance CPU,12 bits high precision AD conversion chip are applied,built-in unique algorithm,thoroughly
eliminate valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning,control unit modular design and potting processing are applied to guarentee components work reliable
and greatly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and
replacement.
△ Menu can report failure in real time(including stuck situation or other fails caused by actuator does not put valve on/off
position in place)and output failure warning signal .
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to “On” or “Off” direction,to bring convenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
3 4 5 6 7
Model Torque Voltage Wiring Feedback Fault Time Speed Rotation Enclosure Manual Position Housing Output
signals regulation angle override indicator material shaft
AC/DC Female
24V 90°/300° IP67 Hexagon Mechanical PC+PET octagon
MTD-01C 10Nm B3/ BD3 J Type A Type 5s PUL/PWM spanner indicator or
/B33/B44 /F Type or
AC/DC ≤330° /button OLED indicator male square
95-265V
※ MTD-01 Series : PC+PET
Product overview
◎ Matched valves: 2-way, 3-way ball valve and butterfly valve
◎ Rated voltage: DC24V
◎ Running time: about 3S
◎ Control feedback mode: BD3J,B3J,B33J,B43J(feedback synchronous with arrival)
◎ Alarm output: A(Relay contact feedback)
1
◎ Achievable mode: 2 way /3 way
◎ High performance brushless motor,overload or overheated
protection of internal motor
◎ It can be used 20,000 times 2
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show valve opening angle and external control command.Enter sleeping state automatically after about 5 minutes,it could
display location state and its control command during sleeping time.
△ Original valve adjustment mode:cover-opening and interactive
step1:Press the button to control valve to the position of “counterclockwise full open”, then save it .
step2:Press the button to control valve to the position of “clockwise full close” ,then save it to finish the valve adjustment.
Thoroughly eliminate the complex and inconvenient factors caused by mechanical positioning.
△ 16 bits high performance CPU,12 bits high precision AD conversion chip are applied,built-in unique algorithm,thoroughly
eliminate valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning,control unit modular design and potting processing are applied to guarentee components work reliable
and greatly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and
replacement.
△ Menu can report failure in real time(including stuck situation or other fails caused by actuator does not put valve on/off
position in place)and output failure warning signal .
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to “On” or “Off” direction,to bring convenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
3 4 5 6 7
Model Torque Voltage Wiring Feedback Fault Time Speed Rotation Enclosure Manual Position Housing Output
signals regulation angle override indicator material shaft
Product overview
◎ Matched valves: 2-way, 3-way ball valve and butterfly valve
◎ Rated voltage: AC/DC95V-265V,AC/DC24V
◎ Control feedback mode: KT32J
◎ Alarm output: A(Relay contact feedback)
◎ Achievable mode: 2 way /3 way 1
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show valve opening angle and external control command.Enter sleeping state automatically after about 5 minutes,it could
display location state and its control command during sleeping time.
△ Original valve adjustment mode:cover-opening and interactive
step1:Press the button to control valve to the position of “counterclockwise full open”, then save it .
step2:Press the button to control valve to the position of “clockwise full close” ,then save it to finish the valve adjustment.
Thoroughly eliminate the complex and inconvenient factors caused by mechanical positioning.
△ 16 bits high performance CPU,12 bits high precision AD conversion chip are applied,built-in unique algorithm,thoroughly
eliminate valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning,control unit modular design and potting processing are applied to guarentee components work reliable
and greatly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and
replacement.
△ Menu can report failure in real time(including stuck situation or other fails caused by actuator does not put valve on/off
position in place)and output failure warning signal .
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to “On” or “Off” direction,to bring convenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
3 4 5 6 7
Model Torque Voltage Wiring Feedback Fault Time Speed Rotation Enclosure Manual Position Housing Output
signals regulation angle override indicator material shaft
AC/DC Female
24V 90°/300° IP67 Hexagon Mechanical octagon
MTD-01C-KT 6Nm B3/ BD3 J Type A Type 5s PUL/PWM spanner indicator or PC+PET
AC/DC /B33/B44 /F Type or
95-265V
≤330° /button OLED indicator male square
Product overview
◎ Matched valves: 2-way, 3-way ball valve and butterfly valve
◎ Rated voltage: AC/DC95V-265V,AC/DC24V
◎ Control feedback mode: YW44 ( achieve the level
control by directly connected to the level sensor)
◎ Achievable mode: 2 way /3 way 1
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show valve opening angle and external control command.Enter sleeping state automatically after about 5 minutes,it could
display location state and its control command during sleeping time.
△ Original valve adjustment mode:cover-opening and interactive
step1:Press the button to control valve to the position of “counterclockwise full open”, then save it .
step2:Press the button to control valve to the position of “clockwise full close” ,then save it to finish the valve adjustment.
Thoroughly eliminate the complex and inconvenient factors caused by mechanical positioning.
△ 16 bits high performance CPU,12 bits high precision AD conversion chip are applied,built-in unique algorithm,thoroughly
eliminate valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning,control unit modular design and potting processing are applied to guarentee components work reliable
and greatly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and
replacement.
△ Menu can report failure in real time(including stuck situation or other fails caused by actuator does not put valve on/off
position in place)and output failure warning signal .
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to “On” or “Off” direction,to bring convenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
3 4 5 6 7
Model Torque Voltage Wiring Feedback Fault Time Speed Rotation Enclosure Manual Position Housing Output
signals regulation angle override indicator material shaft
AC/DC Female
MTD- 24V 90°/300° Hexagon Mechanical octagon
10Nm YW44 J Type A Type 5s PUL/PWM IP67 spanner indicator or PC+PET
01CYW AC/DC ≤330° /F Type or
/button OLED indicator male square
95-265V
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: AC/DC95V-265V,AC/DC24V
◎ Control signal: 4-20mA,0-20mA,0-10V,0-5V,1-5V,2-10V
◎ Position feedback: 4-20mA
◎ Position accuracy: ±1%
◎ Alarm output: A(Relay contact feedback)
◎ High performance brushless motor,overload or overheated
protection of internal motor
◎ It can be used up to 20,000 times 1
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show valve opening angle and external control command.Enter sleeping state automatically after about 5 minutes,it could
display location state and its control command during sleeping time.
△ Original valve adjustment mode:cover-opening and interactive
step1:Press the button to control valve to the position of “counterclockwise full open”, then save it .
step2:Press the button to control valve to the position of “clockwise full close” ,then save it to finish the valve adjustment.
Thoroughly eliminate the complex and inconvenient factors caused by mechanical positioning.
△ 16 bits high performance CPU,12 bits high precision AD conversion chip are applied,built-in unique algorithm,thoroughly
eliminate valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ ※TCR-01 total series and other DC24V series:built-in motor control module,variable frequency speed control of
motor can realize accurate positioning.
△ Non-contact positioning,control unit modular design and potting processing are applied to guarentee components work reliable
and greatly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and
replacement.
△ Menu can report failure in real time(including stuck situation or other fails caused by actuator does not put valve on/off
position in place)and output failure warning signal .
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to “On” or “Off” direction,to bring convenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
2 3 4
Model Torque Voltage Time Wiring Feedback Fault Rotation Enclosure Manual Position Housing Output
signals angle override indicator material shaft
4-20mA
AC/DC24V 0-20mA Female
90°/300° IP67 Hexagon Mechanical octagon
MTD-01T 10Nm 0-5V 4-20mA A Type spanner indicator or PC+PET
AC/DC 6s 1-5V ≤330° /F Type or
/button OLED indicator male square
95-265V 0-10V
2-10V
Notice *1.Test condition:Test under rated load, 25℃ working temperature and 50% humidity,one test circle( two times switching cycle),which will be influenced by different load
and working environment.
*2.Fault signals are selectable function,output by relay,factory defaults settings do not take this function.
*3.F type is suitable for the ambient of high humidity(≥90%) but without long-term rain.
*4.Use hexagon spanner when power-off,or use button when power-on.
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: DC24V
◎ Running time: about 3S
◎ Control signal: 4-20mA,0-20mA,0-10V,0-5V,1-5V,2-10V
◎ Position feedback: 4-20mA
◎ Position accuracy: ±1%
◎ Alarm output: A(Relay contact feedback)
◎ High performance brushless motor,overload or overheated
protection of internal motor
◎ It can be used up to 20,000 times 1
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show valve opening angle and external control command.Enter sleeping state automatically after about 5 minutes,it could
display location state and its control command during sleeping time.
△ Original valve adjustment mode:cover-opening and interactive
step1:Press the button to control valve to the position of “counterclockwise full open”, then save it .
step2:Press the button to control valve to the position of “clockwise full close” ,then save it to finish the valve adjustment.
Thoroughly eliminate the complex and inconvenient factors caused by mechanical positioning.
△ 16 bits high performance CPU,12 bits high precision AD conversion chip are applied,built-in unique algorithm,thoroughly
eliminate valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ ※MTD-01 total series and other DC24V series:built-in motor control module,variable frequency speed control of
motor can realize accurate positioning.
△ Non-contact positioning,control unit modular design and potting processing are applied to guarentee components work reliable
and greatly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and
replacement.
△ Menu can report failure in real time(including stuck situation or other fails caused by actuator does not put valve on/off
position in place)and output failure warning signal.
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to “On” or “Off” direction,to bring convenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
2 3 4
Model Torque Voltage Time Wiring Feedback Fault Rotation Enclosure Manual Position Housing Output
signals angle override indicator material shaft
4-20mA
0-20mA Female
0-5V 90°/300° IP67 Hexagon Mechanical octagon
MTD-01TH 10Nm AC/DC24V 3S 4-20mA A Type spanner indicator or PC+PET or
1-5V ≤330° /F Type
0-10V /button OLED indicator male square
2-10V
※ MTD-01 Series : PC+PET
Notice *1.Test condition:Test under rated load, 25℃ working temperature and 50% humidity,one test circle( two times switching cycle),which will be influenced by different load
and working environment.
*2.Fault signals are selectable function,output by relay,factory defaults settings do not take this function.
*3.F type is suitable for the ambient of high humidity(≥90%) but without long-term rain.
*4.Use hexagon spanner when power-off,or use button when power-on.
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: AC/DC95V-265V,AC/DC24V
◎ Control signal: 4-20mA-KT、0-20mA-KT、0-5V-KT、
1-5V-KT、0-10V-KT、2-10V-KT
◎ Position feedback: 4-20mA
◎ Position accuracy: ±1%
◎ Alarm output: A(Relay contact feedback)
◎ High performance brushless motor,overload or overheated
protection of internal motor
1
◎ It can be used up to 20,000 times
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show valve opening angle and external control command.Enter sleeping state automatically after about 5 minutes,it could
display location state and its control command during sleeping time.
△ Original valve adjustment mode:cover-opening and interactive
step1:Press the button to control valve to the position of “counterclockwise full open”, then save it .
step2:Press the button to control valve to the position of “clockwise full close” ,then save it to finish the valve adjustment.
Thoroughly eliminate the complex and inconvenient factors caused by mechanical positioning.
△ 16 bits high performance CPU,12 bits high precision AD conversion chip are applied,built-in unique algorithm,thoroughly
eliminate valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ ※MTD-01 total series and other DC24V series:built-in motor control module,variable frequency speed control of
motor can realize accurate positioning.
△ Non-contact positioning,control unit modular design and potting processing are applied to guarentee components work reliable
and greatly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and
replacement.
△ Menu can report failure in real time(including stuck situation or other fails caused by actuator does not put valve on/off
position in place)and output failure warning signal .
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to “On” or “Off” direction,to bring convenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
2 3 4
Model Torque Voltage Time Wiring Feedback Fault Rotation Enclosure Manual Position Housing
Output
signals angle overrid indicator material
shaft
4-20mA-KT
AC/DC24V 0-20mA-KT
90°/300° Hexagon Mechanical Female
0-5V-KT IP67 octagon
MTD-01T-KT 6Nm 5s 4-20mA A Type /F Type spanner indicator or PC+PET
AC/DC 1-5V-KT ≤330° /button OLED indicator or
95-265V 0-10V-KT male square
2-10V-KT
※ MTD-01 Series : PC+PET
Notice *1.Test condition:Test under rated load, 25℃ working temperature and 50% humidity,one test circle( two times switching cycle),which will be influenced by different load
and working environment.
*2.Fault signals are selectable function,output by relay,factory defaults settings do not take this function.
*3.F type is suitable for the ambient of high humidity(≥90%) but without long-term rain.
*4.Use hexagon spanner when power-off,or use button when power-on.
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage:AC/DC95V-265V,AC/DC24V
◎ Control feedback mode: RS485(Modbus),CANBus 2.0B/Mbus(customized)
◎ Achievable mode: 2 way /3 way 1
Purchase guide
3 4
Model Torque Voltage Time Communication Rotation Enclosure Manual Position Housing Output
angle override indicator material shaft
Hexagon Mechanical Female
AC/DC24V RS485/CANBUS2.0B 90°/300° IP67 octagon
MTD-01B 10Nm 5s Compatible Mobus /F Type spanner indicator or PC+PET
AC/DC95-265V ≤330° /button OLED indicator or
male square
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: DC24V
◎ Running time: about 3S
◎ Control feedback mode: RS485(Modbus),CANBus 2.0B/Mbus (customized)
◎ Achievable mode: 2 way/3 way 1
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show Baud rate,ID address,valve opening angle and external control command.Enter sleeping state automatically after about
5 minutes,while it could display location state and its control command at sleeping time.
△ Original valve adjustment mode-free cover-opening :
Intelligent Bus is same as Intelligent On/Off series.
△ 16 bits high performance CPU,12 bits high precision AD conversion are applied,built-in unique algorithm,thoroughly eliminate
valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning is applied,control unit modular design and potting processing to guarentee components work reliable.
vastly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and replacement.
△ Menu can report failure in real time(including stuck situation or other reasons which lead actuator fail to put valve on/off
position )and output failure warning signal .
△ Menu operation can change Bus ID address and Baud rate automatically.
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to on or off direction,to bring vonvenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
3 4
Model Torque Voltage Time Communication Rotation Enclosure Manual Position Housing Output
angle override indicator material shaft
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: AC/DC95V-265V,AC/DC24V
◎ Control feedback mode: RS485(Modbus),CANBus 2.0B/Mbus (customized)
◎ Achievable mode: 2 way/3 way 1
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show Baud rate,ID address,valve opening angle and external control command.Enter sleeping state automatically after about
5 minutes,while it could display location state and its control command at sleeping time.
△ Original valve adjustment mode-free cover-opening :
Intelligent Bus is same as Intelligent On/Off series.
△ 16 bits high performance CPU,12 bits high precision AD conversion are applied,built-in unique algorithm,thoroughly eliminate
valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning is applied,control unit modular design and potting processing to guarentee components work reliable.
vastly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and replacement.
△ Menu can report failure in real time(including stuck situation or other reasons which lead actuator fail to put valve on/off
position )and output failure warning signal .
△ Menu operation can change Bus ID address and Baud rate automatically.
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to on or off direction,to bring vonvenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
3 4
Model Torque Voltage Time Communication Rotation Enclosure Manual Position Housing Output
angle override indicator material shaft
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: AC/DC95V-265V,AC/DC24V
◎ Communication Mode: RF433/868/915MHZ,FSK,LORA,RF Ocean (single control)
◎ Communication protocol: Compatible Modbus
◎ Wireless Module: SX1278/SX1276/A7108
◎ Communication distance: The maximum is 3Km
◎ Achievable mode: 2 way/3 way 1
◎ High performance brushless motor,overload or overheated
protection of internal motor
◎ It can be used up to 20,000 times 2
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show Baud rate,ID address,valve opening angle and external control command.Enter sleeping state automatically after about
5 minutes,while it could display location state and its control command at sleeping time.
△ Original valve adjustment mode-free cover-opening :
Intelligent Bus is same as Intelligent On/Off series.
△ 16 bits high performance CPU,12 bits high precision AD conversion are applied,built-in unique algorithm,thoroughly eliminate
valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning is applied,control unit modular design and potting processing to guarentee components work reliable.
vastly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and replacement.
△ Menu can report failure in real time(including stuck situation or other reasons which lead actuator fail to put valve on/off
position )and output failure warning signal .
△ Menu operation can change Bus ID address and Baud rate automatically.
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to on or off direction,to bring vonvenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
3 4
Model Torque Voltage Time Communication Rotation Enclosure Manual Position Housing Output
angle override indicator material shaft
FSK/LORA(Modbus) Female
AC/DC24V RF 433/868M/915M 90°/300° IP67 Hexagon Mechanical octagon
MTD-01R 10Nm 5s ≤330° /F Type spanner indicator or PC+PET or
RF Ocean
AC/DC95-265V (single control) /button OLED indicator male square
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: DC24V
◎ Running time: about 3S
◎ Communication Mode: RF433/868/915MHZ,FSK,LORA,RF Ocean (single control)
◎ Communication protocol: Compatible Modbus
◎ Wireless Module: SX1278/SX1276/A7108
◎ Communication distance: The max is 3Km
1
◎ Achievable mode: 2 way/ 3 way
◎ High performance brushless motor,overload protection of internal motor
◎ It can be used up to 20,000 times 2
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show Baud rate,ID address,valve opening angle and external control command.Enter sleeping state automatically after about
5 minutes,while it could display location state and its control command at sleeping time.
△ Original valve adjustment mode-free cover-opening :
Intelligent Bus is same as Intelligent On/Off series.
△ 16 bits high performance CPU,12 bits high precision AD conversion are applied,built-in unique algorithm,thoroughly eliminate
valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning is applied,control unit modular design and potting processing to guarentee components work reliable.
vastly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and replacement.
△ Menu can report failure in real time(including stuck situation or other reasons which lead actuator fail to put valve on/off
position )and output failure warning signal .
△ Menu operation can change Bus ID address and Baud rate automatically.
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to on or off direction,to bring vonvenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
3 4
Model Torque Voltage Time Communication Rotation Enclosure Manual Position Housing Output
angle override indicator material shaft
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: AC/DC95V-265V,AC/DC24V
◎ Communication Mode: RF433/868/915MHZ,FSK,LORA,RF Ocean (single control)
◎ Communication protocol: Compatible Modbus
◎ Wireless Module: SX1278/SX1276/A7108
◎ Communication distance: The maximum is 3Km
◎ Achievable mode: 2 way/ 3 way 1
◎ High performance brushless motor,overload or overheated
protection of internal motor
◎ It can be used up to 20,000 times 2
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show Baud rate,ID address,valve opening angle and external control command.Enter sleeping state automatically after about
5 minutes,while it could display location state and its control command at sleeping time.
△ Original valve adjustment mode-free cover-opening :
Intelligent Bus is same as Intelligent On/Off series.
△ 16 bits high performance CPU,12 bits high precision AD conversion are applied,built-in unique algorithm,thoroughly eliminate
valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning is applied,control unit modular design and potting processing to guarentee components work reliable.
vastly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and replacement.
△ Menu can report failure in real time(including stuck situation or other reasons which lead actuator fail to put valve on/off
position )and output failure warning signal .
△ Menu operation can change Bus ID address and Baud rate automatically.
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to on or off direction,to bring vonvenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
3 4
Model Torque Voltage Time Communication Rotation Enclosure Manual Position Housing Output
angle override indicator material shaft
FSK/LORA(Modbus) Female
AC/DC24V Hexagon Mechanical
RF 433/868M/915M 90°/300° IP67 octagon
MTD-01R 6Nm 5s spanner indicator or PC+PET or
AC/DC95-265V RF Ocean ≤330° /F Type /button OLED indicator
-KT (single control) male square
Product overview
◎ Matched valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: AC/DC95V-265V,AC/DC24V
◎ Timer mode: pulse mode , time mode
◎ Loop mode : loop by days , loop by weeks
◎ Adopted high-performance brushless motor,Overload protection of internal motor
◎ It can be used up to 20,000 times.
1
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show valve opening angle and external control command.Enter sleeping state automatically after about
5 minutes,while it could display location state and its control command at sleeping time.
△ Original valve adjustment mode-free cover-opening :
Intelligent Bus is same as Intelligent On/Off series.
△ 16 bits high performance CPU,12 bits high precision AD conversion are applied,built-in unique algorithm,thoroughly eliminate
valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning is applied,control unit modular design and potting processing to guarentee components work reliable.
vastly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and replacement.
△ Menu can report failure in real time(including stuck situation or other reasons which lead actuator fail to put valve on/off
position )and output failure warning signal .
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to on or off direction,to bring vonvenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
Rotation 2
Manual
3
Position Housing Output
Model Torque Voltage Time Timer model Enclosure material shaft
angle override indicator
Pluse mode Mechanical Female
Time mode Hexagon
AC/DC24V 90°/300° spanner indicator or octagon
MTD-01D 10Nm 5s IP67 / F type OLED PC+PET or
AC/DC95-265V Loop by days ≤330° /button
indicator male square
Loop by weeks
Notice *1.Test condition:Test under rated load, 25℃ working temperature and 50% humidity,one test circle( two times switching cycle),which will be influenced by different load
and working environment.
*2.F type is suitable for the ambient of high humidity(≥90%) but without long-term rain.
*3.Use hexagon spanner when power-off,or use button when power-on.
Product overview
◎ Install valves: 2-way,3-way ball valve and butterfly valve
◎ Rated voltage: DC24V
◎ Running time: about 3S
◎ Timer mode: pulse, timer
◎ Loop mode : loop by days , loop by weeks
◎ Adopted high-performance brushless motor,Overload protection of internal motor
◎ It can be used up to 20,000 times. 1
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show,valve opening angle and external control command.Enter sleeping state automatically after about
5 minutes,while it could display location state and its control command at sleeping time.
△ Original valve adjustment mode-free cover-opening :
Intelligent Bus is same as Intelligent On/Off series.
△ 16 bits high performance CPU,12 bits high precision AD conversion are applied,built-in unique algorithm,thoroughly eliminate
valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning is applied,control unit modular design and potting processing to guarentee components work reliable.
vastly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and replacement.
△ Menu can report failure in real time(including stuck situation or other reasons which lead actuator fail to put valve on/off
position )and output failure warning signal .
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to on or off direction,to bring vonvenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
Rotation 2
Manual
3
Position Housing Output
Model Torque Voltage Time Timer model Enclosure material shaft
angle override indicator
Pluse mode Mechanical Female
Time mode 90°/300° Hexagon indicator or octagon
MTD-01DH 10Nm DC24V 2S IP67 / F type spanner PC+PET
≤330° OLED or
Loop by days /button indicator male square
Loop by weeks
Notice *1.Test condition:Test under rated load, 25℃ working temperature and 50% humidity,one test circle( two times switching cycle),which will be influenced by different load
and working environment.
*2.F type is suitable for the ambient of high humidity(≥90%) but without long-term rain.
*3.Use hexagon spanner when power-off,or use button when power-on.
Product overview
Product features
△ 1.3” OLED screen,it features no view restriction, high brightness,energy saving and environment protection,in real time to
show valve opening angle and external control command.Enter sleeping state automatically after about
5 minutes,while it could display location state and its control command at sleeping time.
△ Original valve adjustment mode-free cover-opening :
Intelligent Bus is same as Intelligent On/Off series.
△ 16 bits high performance CPU,12 bits high precision AD conversion are applied,built-in unique algorithm,thoroughly eliminate
valve on/off inaccuracy caused by mechanical hysteresis,espacially suitable for 3-way valve adjustment.
△ Non-contact positioning is applied,control unit modular design and potting processing to guarentee components work reliable.
vastly improve product service life;Interface uses standard connectors,convenient for installment,adjustment and replacement.
△ Menu can report failure in real time(including stuck situation or other reasons which lead actuator fail to put valve on/off
position )and output failure warning signal .
△ Menu operation can realize exchange of valve control command .
△ Menu operation can switch freely between remote control and local setting,press the button to realize opening/closing .
△ Menu operation can set valve off position deviate to on or off direction,to bring vonvenience to local valve adjustment
compared with “Normal On/Off mechanical positioning”.
△ Menu operation can adjust valve running speed of the actuator in real time .
△ Menu operation can restore factory default setting.
Purchase guide
Rotation 2
Manual
3
Position Housing Output
Model Torque Voltage Time Timer model Enclosure material shaft
angle override indicator
Notice *1.Test condition:Test under rated load, 25℃ working temperature and 50% humidity,one test circle( two times switching cycle),which will be influenced by different load
and working environment.
*2.F type is suitable for the ambient of high humidity(≥90%) but without long-term rain.
*3.Use hexagon spanner when power-off,or use button when power-on.
11x11
A
4×M5 Hole ≤12mm
76
66
F03
A
4×M6
F05
4×M5
66
F03
4×M6
F05
9.5
12×12
Main parts
⑤ ④
⑥ Parts Material Parts Material
⑦ ②
Actuator Heatproof PC+PET
1 7 1.3” LCD Screen OLED
or Casting aluminum
③ 2 Indicator Transparent AS 8 Label PVC
Assembly Diagram1 UPVC plastic ball valve added with bracket NOTICE:
Assembly Diagram2 3-piece stainless steel ball valve ※1.When assembling with valve,it’s recommand to use spring washer and flat washer to fix screw nut.
※2.It’s forbidden to use anaerobic glue or UV glue,if needed,please use 704 glue and adhere quickly.
Assembly Diagram3 Stainless steel 3-way ball valve ※3.Casing is avoided to contact with organic solvent,such as kerosene, butanone and etc,or the casing
will be damaged.
□1.If the ball valve is out of operation for a long time, and the torque value of first on or off is the max torque.
□2.When installing direct mount model valve, the hole deep ≤15mm. It requires cutting if the output shaft is longer than 17mm.
□3. Pls pay attention to the following items if you install the bracket and coupling by yourself:
※ The intensity of bracket should meet the using requirements: the bracket twisting extent ≤0.2mm in the process of on or off.
※ The parallelism of bracket ≤0.5mm.
※ When processing the shaft hole at both end of the coupling, it is necessary to ensure the accuracy and concentricity. The
purpose is to make sure the mechanical hysteresis ≤10°, otherwise it will cause the actuator unable to work.
□4. Screw should be installed spring washer、flat washer, and we suggest you daub some glue cement around the screw in
case of screw loosening.
□5. After installation, user should switch the valve on and off one time with handle device first. Modifying the valve after make
sure it works well.
Red Red
RD OFF RD OFF
1 SW L 1 SW L
Black Black
BK ON Fuse
BK ON Fuse
White White
WT Feedback_Com
WT Res_Com1
Gray Gray
GY Feedback_Open 10K GY Res_Position
Brown Brown
BN Feedback_Close
BN Res_Com2
Yellow/Green
PE
PE Y/G PE Y/G
Yellow/Green
Control
Red
BU
Blue
N RD L
ON OFF
Black
RD Red
OFF BK SW
1 SW L White
Black WT
BK ON Fuse Feedback_Com
Gray
GY
Gray GY Feedback_Open
Feedback_Open
Brown
BN
Brown
Feedback_Close
BN Feedback_Close
Y/G
Yellow/Green
PE Y/G Yellow/Green PE
Control instructions:
Control instructions: □ If SW is disconnected;the actuator will drive valve close clockwise .When
□ SW is connected with RD ,the actuator will rotate clockwise .When the valve is closed the valve is closed completely, WT is connected with BN ,giving signal of full closing.
completely, RD is connect with BN ,giving signal of full closing. □ If SW is connected,the actuator will drive valve open counterclockw ise .When
□ SW is connected with BK ,the actuator will rotate conterclockwise .When the valve is open the valve is open completely, WT is connected with GY ,giving signal of full opening .
completely, BK is connect with GY ,giving signal of full opening. Notice 1: WT is not connected with GY BN ,when the actuator is running.
※
※ Notice 1: RD is not connected with BN , BK is not connected with GY when the actuator is Notice 2: The time of feedback signal is a little earlier than the time when actuator reaches its
※
rotating. actual position,so please do not cut power immediately after you get the feedback signal.
※ Notice 2: The time of feedback signal is synchronous with the time when valve reaches targeted
positon.
B3S-【DC series】
KT32S/BD3S-【DC series】
Farad Cap Blue
Blue BU V-
BU V-
Red
Red RD V+
Driver
Control
RD
Control
OFF
Motor
ON OFF
SW V+ Black
BK Black
ON Fuse BK SW
White
WT
White
Feedback_Com
WT Feedback_Com
Gray
GY Gray
Feedback_Open
GY Feedback_Open
Brown
BN
Brown
Feedback_Close BN Feedback_Close
Yellow/Green
PE
PE
PE Y/G Yellow/Green
PE
PE Y/G
Control instructions:
□ SW is connected with RD ,the actuator will rotate clockwise .When the valve is closed Control instructions:
completely, WT is connect with BN ,giving signal of full closing. □ If SW is disconnected;the actuator will drive valve close clockwise .When
□ SW is connected with BK ,the actuator will rotate counterclockwise .When the valve is open the valve is closed completely, WT is connected with BN ,giving signal of full closing.
completely,WT is connect with GY ,giving signal of full opening. □ If SW is connected,the actuator will drive valve open anticlockwise .When
※ Notice 1: WT is not connected with GY and BN ,when the actuator is rotating. the valve is open completely, WT is connected with GY ,giving signal of full opening .
※ Notice 2:The time of feedback signal is a little earlier than the time when actuator reaches its Notice 1:
※ is
WT not connected with BN GY ,when the actuator is running.
actual position,so please do not cut power immediately after you get the feedback signal. Notice 2:The time of feedback signal is a little earlier than the time when actuator reaches its
※
actual position,so please do not cut power immediately after you get the feedback signal.
※ Notice 3:When power cut,actuator will drive valve to close.
BU N BU V-
RD RD
Control
OFF OFF
Motor
1 SW L SW V+
BK ON Fuse BK ON Fuse
WT Feedback_Com WT Feedback_Com
GY Feedback_Open GY Feedback_Open
BN Feedback_Close BN Feedback_Close
PE
PE Y/G PE
PE
PE Y/G
BD3C
BU N
Control
RD L
ON OFF
BK SW
WT Feedback_Com
GY Feedback_Open
BN Feedback_Close
PE Y/G
Control instructions:
□ If SW is disconnected;the actuator will drive valve close clockwise .When
the valve is closed completely, WT is non-connected with BN ,giving signal of closing.
□ If SW is connected,the actuator will drive valve open anticlockwise .When
the valve is open completely, WT is non-connected with GY ,giving ignal of opening .
※ Notice 1: WT is connected with GY BN ,when the actuator is running.
※ Notice 2:The feedback signal is a little earlier than the actual position,so please do not
cut power immediately,when you get the feedback signal.
Wiring instructions:
Black
1.Fuse:please refer to manual for more parameters. Red
Blue
2.SW load capability:please refer to manual for more parameters. Gray
White
( Wiring Diagram )
3.Feedback signal contact load capacity:0.1A/250VAC 0.5A/30VDC. Brown
4.Please make sure actuator connect ground reliably(only KT32S). Yellow/Green
Control
Blue
Control
N /-
Motor
BU N /-
Motor
AC-DC
AC-DC Red
Red RD
RD L /+ OFF
L /+
ON OFF Fuse SW
Black BK Black
ON
Pos_Sensor BK SW
Pos_Sensor
Voltage Signal
Voltage Signal Gray
Regulator Acquisition
GY
Gray
Feedback_Open
Regulator Acquisition
GY Feedback_Open
M
M
White WT White
16Byte
Relay WT Feedback_Com
1.3”
16Byte
Relay Feedback_Com
1.3” MCU
Brown
OLED
MCU
Relay BN
Brown
Feedback_Close
OLED
Screen
Relay BN Feedback_Close
Screen
Yellow/Green
PE Y/G
Yellow/Green PE Y/G
Blue Blue
Control
Control
BU N /- BU N /-
Motor
Motor
AC-DC AC-DC
Red Red
RD L /+ RD OFF
ON OFF Fuse SW L /+
Black Black
Pos_Sensor BK Pos_Sensor BK ON
Voltage Signal SW Voltage Signal
Regulator Acquisition Gray Regulator Acquisition Gray
GY Feedback_Open GY Feedback_Open
M
White White
Relay WT Feedback_Com Relay WT Feedback_Com
1.3” 16Byte 1.3” 16Byte
OLED Brown OLED Brown
Screen
MCU Relay BN Feedback_Close
Screen
MCU Relay BN Feedback_Close
Purple Purple
Relay PL Fault output signal Relay PL Fault output signal
Yellow/Green
PE Y/G PE Y/G Yellow/Green
B33J B44
Blue Blue
Control
BU BU
Control
N /- N /-
Motor
Motor
White
16Byte
Relay WT Feedback_Com
16Byte
Signal
1.3” MCU 1.3” Acquisition
Brown MCU
OLED
Screen
Relay BN Feedback_Close OLED
Screen
Yellow/Green
PE Y/G PE Y/G Yellow/Green
SW1 SW2 Flow direction Feedback signal SW1 SW2 Control instructions
connect disconnect 0° WT connect with BN disconnect disconnect Full closing
connect connect 300°(could be free set by menu) WT connect with GY BN connect disconnect Open60°±10%
connect connect Full opening
※ Note 1: WT is not connected with GY and BN ,when the actuator is operating.
※ Note 2:After power cut,the feedback and fault signal will disappear, WT is not connected with GY and BN .
B43JA【Alert】 B33JA【Alert】
Blue
Control
BU N /-
Motor
Blue
Control
BU N /-
Motor
AC-DC
Pink AC-DC
PK L /+ Red SW1
RD L /+
Pos_Sensor Red SW1
RD Pos_Sensor BK
Black SW2
Voltage Signal Black SW2 Voltage Signal
Regulator Acquisition BK Regulator Acquisition Gray
GY Feedback_Open
M
Gray
GY Feedback_Open White
M
Relay
WT Feedback_Com
White 1.3”
Relay
WT Feedback_Com OLED 16Byte
Relay BN
Brown
Feedback_Close
1.3” Screen MCU
OLED 16Byte Brown
MCU Relay BN Feedback_Close Purple
Screen Relay PL Fault output signal
Purple
Relay PL Fault output signal Yellow/Green
PE Y/G
Yellow/Green
PE Y/G
Control instructions:
※ Note 1: WT is not connected with GY BN PL ,when the actuator is running.
Control instructions
※ Note 2:When actuator was stuck or other fails which lead valve unable to open or close completely, WT SW1 SW2 Flow direction Feedback signal
connects withPL ,send warning signal.
connect disconnect 0° WT connect with BN
※ Note 3:After power cut,the feedback and fail signal will disappear, WT is not connected with GY BN PL .
disconnect connect 90° WT connect with GY
※ Note 4:45° is the third position,whose value(10%-90%)could be set by menu.
※ Note 5:When SW1,SW2 are both disconnected,it means no control signal,factory default setting is valve-off connect connect 45°(could be freely set by menu) WT connect with GY BN
command.
Temperature Switch
A
B
Heating Resistor
Control
Control
Motor
AC-DC
Motor
AC-DC
Red Red
RD L /+ RD Fuse
L /+
Voltage Fuse Voltage
Position Position Regulator
Sensor Regulator Sensor
Brown Brown Vout : [0-5V]
BN
Iout: [4-20mA]
4-20mA BN A 0-5V
Transmitter Transmitter Rx≥10K
White
Rx ≤250Ω
White
WT WT
M
M
AC-DC
Red
□3 Make sure voltage practicable range, ※otherwise it will damage the control module.
RD Fuse
L /+ □4 GY is feedback current input: 4-20mA,0-20mA,0-5V,0-10V,2-10V,input impedance refers to relevant
Voltage wiring diagram.
Position
Sensor Regulator □5 BN is control current output:4-20mA.
16Byte 10kΩ
Gray operate valve full-open,full-close or keep.For other control mode “0-20mA,0-10V,0-5V”,such setting is invalid.
MCU
1.3”
10kΩ GY A Iin: [2-10V]
□8 When actuator is stuck or there is other working fails,output fails signal.
OLED [0-10V]
Screen Contactor load capacity:0.1A/DC24V,50mA/230V.
Y/G
Yellow/Green
PE
□9 0-10V output load capacity is ≥10KΩ,wire’s resistance has impact on the accuracy ,please use wire with
lower resistance.
Black Pink
Red Black
Yellow/Green
Motor
AC-DC
Red
RD L /+ Figure 1 (7wiring diagram) Figure2 (9 wiring diagram)
Voltage Fuse
Position Regulator 0-20mA,0-5V,0-10V,2-10V can support alarm signal output functio
n.
Sensor
Brown Iout: [4-20mA] Control instructions -【Alert / 9-core】:
4-20mA BN A
Transmitter
White
Rx≤250Ω □1 RD BU are power supply.
16Byte 200Ω
Gray ※They are forbidden to connect the power supply,otherwise it will damage the control module.
1.3” MCU GY A Iin: [4-20mA]
[0-20mA]
□ 3 Make sure voltage practicable range, ※otherwise it will damage the control module.
OLED Relay
Screen Black □4 GY is control current input: 4-20mA,0-20mA,0-5V,0-10V,2-10V,input impedance refers to relevant
Alert BK wiring diagram.
Fault output signal
PL
Purple □5 BN is feedback current output: 4-20mA.
□6 Vout=Iout·Rx,
Yellow/Green
PE Y/G △Rx is recommended to use low MTDresistor.
△VOUT≤8V,so Rx≤400Ω(recommended Vout=5V,Rx=250Ω/0.25W).
□7 ※For “4-20mA/1-5V/2-10V” control mode,user can set no control signal through “user setting” from menu to
operate valve full-open,full-close or keep.For other control mode “0-20mA,0-10V,0-5V”,such setting is invalid.
4-20mA-KT-A /0-20mA-KT-A 【Alarm】 □8 When actuator is stuck or there is other working fails,output fails signal.
Contactor load capacity:0.1A/DC24V,50mA/230V.
Farad Cap
Blue
□9 0-10V output load capacity is ≥10KΩ,wire’s resistance has impact on the accuracy ,please use wire with
BU N /-
lower resistance.
Control
Motor
AC-DC
RD Red L /+ Control instructions:【Alert / Failsafe/ 9-core】
Position
Voltage Fuse □1 RD BU are power supply.
Sensor Regulator □2 GY WT BN are control input and feedback output .
Brown Iout: [4-20mA] ※They are forbidden to connect the power supply,otherwise it will damage the control module.
4-20mA BN A □ 3 Make sure voltage practicable range, ※otherwise it will damage the control module.
Transmitter Rx
WT
White □4 GY is control current input: 4-20mA,0-20mA,0-5V,0-10V,2-10V,input impedance refers to relevant
M
wiring diagram.
16Byte 200Ω
Gray
1.3” MCU GY A Iin: [4-20mA] □5 BN is feedback current output: 4-20mA.
OLED
Screen
Relay
Black
[0-20mA]
□6 Vout=Iout·Rx,
Alert BK △Rx is recommended to use low MTD resistor.
Fault output signal △VOUT≤8V,so Rx≤400Ω(recommended Vout=5V,Rx=250Ω/0.25W).
Purple
PL □7 ※For “4-20mA/1-5V/2-10V” control mode,user can set no control signal through “user setting” from menu to
Yellow/Green operate valve full-open,full-close or keep.For other control mode “0-20mA,0-10V,0-5V”,such setting is invalid.
PE Y/G
□8 When actuator is stuck or there is other working fails,output fails signal.
Contactor loading capacity:0.1A/DC24V,50mA/230V.
□9 0-10V output load capacity is ≥10KΩ,wire’s resistance has impact on the accuracy ,please use wire with
lower resistance.
L /+
Motor
AC-DC
Blue
BU N /- BK
RD
Fuse
Black
Pos_Sensor
Voltage
BK B_485- BU
GY
Regulator Gray
GY B_485- WT
BN
M
RS485/CANBUS
White Yellow/Green
16Byte RS485/CAN WT A_485+
1.3” MCU ->UART Diagram 1( TCR-01 series wiring connector diagram )
brown
OLED
Screen
BN A_485+
PE YG Yellow/Green
Power
GND
A
RS485/CANBUS
B
RD BU BK WT GY BN RD BU BK WT GY BN RD BU BK WT GY BN RD BU BK WT GY BN
120Ω/0.25W
L / V+
Motor
AC-DC Black
BK N / V-
Fuse
Pos_Sensor
Voltage
Regulator
M
16Byte
RF 433/868 Wireless PC Upper
915Mhz
1.3” MCU Repeaters Computer
OLED
Screen
White
PE WT
RF-KT
Farad Cap
Red
RD
Control
L / V+
Motor
AC-DC
Black
BK N / V-
Fuse
Pos_Sensor
Voltage
Regulator
M
16Byte
RF 433/868 Wireless PC Upper
915Mhz
1.3” MCU Repeaters Computer
OLED
Screen
White
PE WT
Red
Green
Black
White
(MTD-01 series 4-core wiring diagram) (MTD-01 series ANSI plug diagram )
PW+
Control instruction:
Press SW1,controller send valve-on command,controller will show the received command and message.
Press SW2,controller send valve-off command,controller will show the received command and message.
Note 1:Fistly,you need set controlled actuator ID by OLED menu,which is more suitable for single control one actuator.
Note 2:If in need of control several actuators,you can control it by PC-Serial,inside controller comes with USB Serial interrupt
connect controller with PC computer,then finish install drive procedure,you can send command code by the serial on
PC computer which is compatible with MODBUS. Details please refer to Modbus communication protocol.
RF-OCEAN
OCEAN OCEAN
Actuator L/V+ SWITCH SWITCH
L/V- 1 2
Notice: Several ocean switches could control one valve,or several valves could be controlled by one OCEAN SWITCH .
AC-DC
Black
BK N / V-
Fuse
Pos_Sensor Red
Voltage
Regulator Green
Black
M
White
16Byte
1.3” MCU
OLED
Screen (MTD-01 series 4-core wiring diagram)
White
PE WT
M TD-01D-KT
Red
RD
Control
L / V+
Motor
AC-DC
Black
BK N / V-
Fuse
Pos_Sensor
Voltage
Regulator
M
L N
Sensor common
Float sensor with self-lock
Black Wihte(power supplyV+/L) 24V+
Red Blue(power supplyV-/N) GND Switch power
Level 5 area
Level 4 area H
Working environment
□ This product can be used indoor and outdoor.
□ This product is not explosion proof , do not use them in flammable and explosive environment.
□ You need to install protective device for the actuator if it is exposed to the rain or sunshine.
□ Please pay attention to the ambient temp.
□ When installing, you need to consider the reserved space for wiring and repairing.
□ When power on, it is not allowed to dismantle actuator and valve.
□ When power on, it is not allowed to do wiring.
□ ※Forbid the dropped thing hit the device and lead to improper operation.
□ ※Forbid step on it which will cause device malfunction or personal accident.
□ ※It is forbidden to do wiring project in rainy day or when there is water splash.
Safety notice
□ In order to use the device safely for a long time,please pre-read the manual carefully to ensure correct use.
□ Notice item:Please understand the product specification and using method clearly to ensure personal safety danger or prevent device
from damage.
□ In order to indicate damage and danger,here we classify them as “warning ” and “notice ※ ”.
□ Both of contents are very important,which should be obeyed strictly.
□ “Warning ”:It will cause death or serious injury if not obeyed.
□ “Notice ※ ”:It will cause slight injury or device damage if not obeyed.
□ Subject to technical changes.
Innovate
Realize costumer greatest value Technology