Te INSPECTION & TESTING ENGINEERS
F-22805, Sie0, Swejpr Indust Area, UPSIDC, Gestor Noida, Gavtam Budh Nagar20136 (LP) INDIA
Mobile : +91 9810059715, 491 9891174695, Phone : +91 120 4310675
Ema te.aideioiaalcom, Webs: p nero com, Nit eensectonandasigeniearcom
WELDING PROCEDURE QUALIFICATION RECORD
Company Name ‘M/s Revent Airtech LLP Identification No._| RAL/SMAW/PQR/22/01
Welding Process | SMAW Date & Revision | 20/12/2022 Rev. No.00
‘Supporting WPS No, | RAL/SMAW/WPS/22/01 ‘Authorized by | Mr. Tausif Raza
Date&Revision __| 20/12/2022 Rev. 00, Type Manual
Joint Design
Backing
Backing Material
Root Opening (G)
Root Face (R) x
‘Groove Angle (8 9) 60°
Back Gouging NA
Method of Back Gouging | NA
> BASE METAL ite METAL
Material Specification | 55308 [AWS Specification
‘Type or Grade Plate ‘AWS Classification E30aL
Thickness of Groove 4mm F Number 5
Thickness of Fillet(t) NA ‘ANumber 4 -
Pipe Diameter NA ‘Size of Filler Metal 25mm
Maximum Pass Thickness _| Less than 13 mm Filler Metal Product Form _| Flux coated solid
LR ios ace een ies Electrode Trade Name ‘Super
Position of Groove 26 ‘Consumable insert NA
Position of Fillet NA Flux Type NA
Welding Progressi Forward, Sideways
POSTWELD HEAT TREATMEN 3] Preheat Temperature NA
“Temperature Range NA Interpass Temperature | NA
Time Range ‘Other
‘Other
sce a Shielding Gas(es) [NA
‘Mode of Metal Transfer__[ NA ‘Mixture (6) NA.
Current Type oC Flow Rate NA
Polarity DCRP/OCEP Backing NA.
Tungsten Electrode Sie | NA [other NA
‘Current Range ‘See Table Trailing NA
Voltage Range Backing NA,
‘String or Weave Bead Both ‘Multiple or Single Pass
Initial or Interpass Cleaning _| Brushing, grinding ‘Multiple or Single Electrodes _ | Single (E 3041)
Method of Back Gouging | Brushing, Grinding Wire Feed Speed NA
Oscillation NA Travel Speed See Table
Other NA Peening Not allowed —TIE INSPECTION & TESTING ENGINEERS
F-22823, Sie, Swappur Indust Area, UPSIDC, Giese Noida, Geta Buch Nagar:201906 (U.P) INDIA
Mobile : +81 9810059715, +91 9891174696, Phone : +91 120 4310875
Emel: te.mide@otmal.con, Webs: hip tnoia con, htp:twwnspctonendestngengneere.can.
Pass or Process Filler Metals ‘Current Volts ‘Travel Speed
‘Weld Class Dia. Type & Value wy (mam /enin)
Layer(s) (rm) Polarity (Amp.)
SIDE 1
I (root) | SMAW | E300 | 25mm | DCEP 105 24 ton
a SMAW | E304 | 25mm DCEP, 110 24 7
TEST RESULTS
‘Appearance | Satisfactory | Porosity None | Undercut | None Convexity ‘Acceptable
Witnessed/Inspected By | Mr. Kuldeep Kumar, ITE Noida Date of Inspection 10/12/2022
Specimen | Dimensions Area Max Load UTS ‘Character of Failure
No. (mm) _|_(Sq.mm) | (Newton) (mea)
71 19.00*4.00 76.00 42720 562.10 Broken from parent Metal/Ductile
12 “19.00°4.00 76.00 42840 576.84 Broken fram parent Metal/Ductile
TTest Report No.:- ULR-TC567022000016675F Di. 20/12/2022
aa ssa tigncie GUIDED BEND TEST _ |
‘Specimen ‘Type of Bend test Remark ‘Type of Bend test Remark
No. a
RBI Root Bend (180*4t) | Satisfactory FB3 Face Bend (180°4t) __| Satisfactory
~_RB1__| Root Bend (180*4t) | _ Satisfactory FB4 | __Face Bend (180%at) | Satisfactory
‘Test Report No.:- ULR-1C567022000016675F Dt.:- 20/12/2022
Welder’s Name Mr. Ramdev Singh
StampNo. [RS
Tests Conducted By | ITE Greater Noida
Date of Welding | 10/12/2022.
Approved by Issued by
Page 2 of 2TIE INSPECTION & TESTING ENGINEERS
F-22423, SiC, Susp Indust! Ae, UPSIDC, Crete Nid, Geto Buth Nagar 201206 (UP) INDIA
Mobile : +91 9810058715, +81 9091174696. Phone : +81 120 4310675
‘mal: e.eide@icimal ca, Website: hi ewscenotacon haninpecionandesingogieescon
‘WELDING PROCEDURE SPECIFICATION
‘Company Name _ | M/s Revent Airtech LLP
Welding Process _| SMAW
‘Supporting WPQR | RAL/SMAW/POR/22/01, Dt-20/12/2022
Identification No. | RAL/SMAW/wPS/22/01
Revision No. [00 | Date | 20/12/2022
‘Authorized by | Mr. Tausif Raza
Joint Design
Backing
‘Backing Material
Root Opening (6)
Root Face (R)
Groove Angle (0°)
Back Gouging
Method of Back Gouging
Materi I Specification ‘AWS Specification
Type or Grade AWS Classification
‘Thickness of Groove (t) F Number 5
Thickness of Fillet ANumber_ 4
Pipe Diameter ‘Size of Filler Metal 25mm
Maximum Pass Thickness iller Metal Product Form Flux coated solid
| Etectrode Trade Name ‘Any approved brand
Position of Groove ‘Consumable insert
Position of Fillet
Welding Progression Forward, Sideways
ees POSTED NEAT TRENTMENT. | Preheat Temperature
‘Temperature Range NA Interpass Temperature | NA
Time Range NA
Other NA
“Transfer Mode (GMAW) | NA = Mixture (%) NA
Current Type oc Flow Rate NA
Polarity DCRP/DCEP_ Backing NA
Mode of Metal Transfer NA Other NA
Current Range See Table _ [Trailing NA.
Voltage Range See Table
SS 5a a OE
‘String or Weave Bead All ‘Multiple or Single Pass ‘Multiple
Initial or Interpass Cleaning _| Brushing, grinding Multiple or Single Electrodes _| Single (E 304L)
Method of Back Gouging NAL Wire Feed Speed Range NA
Oscillation NAL Travel Speed Range See Table
fone NA Peening Not allowed
i}
Page 1of2Wobite =
‘Srepr eds! Aes, ieee Noida,
tet g0v00se7Is, 8" oeetTT400e, Phone :
mal: te noida com, Webs: hpSwww enol com,
INSPECTION & . TESTING ENGINEERS
Gout Buch Nagar201806 (UP) INDIA
+81 120 4310875
ae
Tae aes
Pass or | Process Filler Metals Current Volts: Travel Speed
Weld Class Dia. | Type& Value ™ (rm {rnin}
Layer(s) (mm) ___| Polarity (amp.)
‘All Runs SMAW | __E304L 2.5 mm. DCEP ‘90-160, 20:30 30-100
Prepared by ‘Approved by tssued by
RAL RAL
Page 2 of 2TE
Mobile :
INSPECTION & TESTING ENGINEERS
22825, Sie, Suapur dust Aes, UPSIDC, Greater Noida, Gav Buch Nace 20196 (U.P) INDIA
+91 9810059716, 491 9891174696, Phone : +91 120 4310875
nal: lela. com, Webs: hpi con, httawninspctonantesingengineers com
WELDER QUALIFICATION RECORD
RAL/SMAW/WQR/SMAW/01_
[00
‘Type of welding _
Backing.
Base Material Specification 55 308
Base Metal Thickness (Butt) 1.5mm to8mm
Pipe dia. Pipe above 24”dia. ad al plates
Filler Metal
Spec. No. 5a 5a
Class £304L £304.
FNo. 5 5
Filler Metal Product Form Flux coated solid Flux coated solid
Gas/Flux Type NA NA
Current Polarity CEP DCEP
Groove Position 26 1G, 1F, 2G, 3F
Weld Progression Forward, Sideways Forward, Sideways
‘Transfer Mode TNA NA
‘Appearance | Satisfactory Porosity | None Undercut None Convexity | Acceptable
Witnessed/Inspected By Mr. Kuldeep Kumar, ITE Noida _| Date of Inspection 10/12/2021
‘Specimen ‘Type of Bend test _ Remark ‘Specimen ‘Type of Bend test Remark
No. No.
RB1 Root Bend (180*4t) Satisfactory FB3 Face Bend (180*4t) Satisfactory
RB2 Root Bend (180*4t) Satisfactory FB4 Face Bend (180*4t) Satisfactory
“Test Report No-= ULR-TC567022000016675F Dt.- 20/12/2022 :
Welding Supervised by __| Mr. Tausif Raza ‘Company [M/s Revent Airtech LLP.
| ARETE Approved by Issued by
Page lofi1 E Mobile : +91 9810059715, #91 9891174696, Phone
INSPECTION & TESTING ENGINEERS
F-22823, Sit-C, Surpur Indus Area, UPSIDC, Greater Noida, Gautam Budh Naga-201906 (UF
INDIA
+91 120 4310675
small: '.noida@hotmaiL.carn, Website: htp:/rwwitenoide com, htp:/wwninspectonandtesingengineers.com
TEST REPORT
Doc. No. 11#/S0P-01 — 1m8/F-34
Test Report Wo. ‘WLR-7056702200001 667SE Date | 20/12/2022 |
[customer's M/s. Revent Airtech LLP
Customer’ s Addr Plot-462, Sector-37, Gurgaon, Haryana —
Gastomer’s SRF No. 198/20224007, Dr. +-20/12/2022 |
Sample(s) Received on | 20/12/2022 Sample(s) Tested on | 20/12/2022 |
[Description of Sample
Ref Standard
Position
| Process
26,
| SMAW
[ASME Sec IX:2021
[Buct Welded Test Coupon (SS 3041: 4mm Thick)
Welder Name : Ramdev Singh
‘Test Method Used
‘ASME Sec 1X:2021
TEST RESULTS
Tensile Test:
Best Id |Max Load| Dimension | Area Urs Tocation/type of Fracture
(Newton) ) (sum?) ove | _ -
a 42720 | 18.00*4.00 | 76.00 | 562.10 | Parent Netal/Ductile
Tr-2 43840 | 19.00°4.00 | 76.00 | 576.84 Parent Netal/Ductile
Test Ta Description [ Result /Observation a
FE-1_| Face Bend Test (180°%4t) | No Crack or Opening Observed:~- Acceptable |
FB-2 | Face Bend Test (160°X4t) | No Crack or Opening Observed:- Acceptable
RB-1 Root Bend Test (180°X4t) | No Crack or Opening Observed:~ Acceptable
‘RB-2 Root Bend Test (180°x4t) | No Crack or Opening Observed:- acceptable _
Romarks:-NA-
l
Samples are not drawn by us.
C-5670
+++ END OF REPORT +++
heucription of the samples ig ac provided by the pecty and total Liability ef work ie limited to the
Shveleed amount,
ast samples, if not collected by customer, will be disposed after 30 days of reporting
‘This report connot be used as evidence in the court of law without written approval of the Lab.
Status of tested and remaining sample (returned to customer Ml put in storage[})
Decision rule applicable in case of conformation required (Decision aule 1f™j 7 Decision sule 2)
Page Lora.
‘Approved for : NTPC, IFFCO, IOCL, BHEL, EIL, L&T, NFL, BOEING, MARUTI, SJVNL ETC