Professional Documents
Culture Documents
TEL:021-69179902 FAX:021-69179781
Manual of SM-04-UL
Number: ProD04039A
Editor: 叶 青
thickness:2.0mm
dimension specification:appearance dimension:160 x 109 mm, LCD dimension:110 x 86 mm
working temperature:-10℃--60℃
working humidity:<95%
上海新时达电气有限公司
Shanghai STEP Electric Co., Ltd.
-1-
STEP ® 显示板使用说明
上海新时达电气有限公司
Shanghai STEP Electric Co., Ltd.
-2-
STEP ® 显示板使用说明
3. Socket specification
socket type
JP8 CH3.96-4
JP9,JP10,JP11,JP12 CH2510-4
上海新时达电气有限公司
Shanghai STEP Electric Co., Ltd.
-3-
STEP ® 显示板使用说明
Communication mode 1:
Communication 1
port
Communication type CAN BUS
Baud rate 25000bps
plug CH3.96-4
PCB port JP8.3: CANH JP8.4 : CANL
上海新时达电气有限公司
Shanghai STEP Electric Co., Ltd.
-4-
STEP ® 显示板使用说明
JP9 spare
7. Function explanation
address code Press up/down button to set address code address code 0~48
setting mode when SW5.1 is ON. range
time setting mode When SW5.2 is ON, it is time function selection by pressing up call button,
it used to change time by pressing down button.
person number Pressing up/down button to set person number allowed to load when the SW2.1
allowed to load is ON.
setting mode
contrast hardware Use a screwdriver to adjust the resistor of potentiometer R53,
adjustment mode adjustment which used to adjust LCD contrast, which can be adjusted in
a big range.
software Pressing up/down button to adjust contrast when SW2.1 and
adjustment SW5.1 are ON before power on, it can be adjusted in a little
range, only used to micro adjustment.
上海新时达电气有限公司
Shanghai STEP Electric Co., Ltd.
-5-
STEP ® 显示板使用说明
display
arrival forecast
yes ; no
direction arrow display
glitter
not
else
mode when forecast glitter
floor number display mode
glitter
not
else
when forecast glitter
forecast time When the received floor number is the same with address code, it will
last from receiving the arrival gong until the signal disappears.
special status display
inspection
normal
no ; special character or Also shows“inspect”
display display other mode
re-leveling ; normal
no
special character or
display display other mode
independent ; normal
no
special character or
display display other mode
fire
normal
no ; special character or Also shows“Fire”
display display other mode
safety ; normal
no
special character or
circuit open display display other mode
lock lift
normal
no ; special character or Also shows“Lock”
display display other mode
error ; normal
no
special character or
display display other mode
overload
normal
no ; special character or Also shows“Overload”
display display other mode
direct
normal
no ; special character or Also shows“Full”
running display display other mode
driver full
normal
no ; special character or Also shows “Full”
load display display other mode
code 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
display 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
code 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
display 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
code 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
display 45 46 47 48 -1 -2 -3 -4 -5 -6 -7 -8 -9
code 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74
display B1 B2 B3 B4 B5 B6 B7 B8 B9 B G M M1 M2 M3
code 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89
display P P1 P2 P3 R R1 R2 R3 L H H1 H2 H3 3A
code 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104
display 5A G1 G2 G3 F C1 C2 C3 C4 C
code 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119
display D1 D2 D3 D4 D 1F 2F 3F 4F 5F 1C 2C 3C 4C 49
code 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134
display 1B 2B 3B 4B 1A 2A 4A CF LB E A UB LG UG 6A
code 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149
display 6B 7A 7B 5B 6C SB K U S EG
code 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164
display KG CF MZ SR Z
code 165 166 167 168 169 170 171
display HP AB PH AA L1 L2 L3
The 4 pin plug is used to induct power supply and communication cables of the display board.
Pin 1 is TXV+, pin 2 is TXV-, they are input power supply DC24V, pin 3 is TXA+, pin 4 is TXA-,
上海新时达电气有限公司
Shanghai STEP Electric Co., Ltd.
-7-
STEP ® 显示板使用说明
4针插头CH3.96-4
双绞线
4孔插头CH3.96-4
When the SM-04-UL is taken as the in car display board, the display board should be set“0”when
lift commissioning, that is: put SW5.1 ON, press up/down button, put SW5.1 OFF till the display
show “0”.
When the SM-04-UL is taken as the hall-call display board, it should be set correct floor
number, put SW5.1 ON, the installed floor number should be the address code, that is from the
base floor 1, one after another floor, put SW5.1 OFF after setting.
a) Packing personnel must wear anti-static gloves (anti-static hand ring, or anti-static
clothes);
c) Can not install it in the air environment of explosive gas, or there will be a danger of
上海新时达电气有限公司
Shanghai STEP Electric Co., Ltd.
-8-
STEP ® 显示板使用说明
fire;
d) Can not uninstall the protection motherboard of parts, which are especially designed,
e) Do not make the cover board and panel sustain power, or there will be a danger of damaging
the controller;
f) Do not install it where there is drip splash, or there will be a danger of damaging the
controller;
g) Do not leave any bolt, washer or metallic pieces in the controller, or there will be a
上海新时达电气有限公司
Shanghai STEP Electric Co., Ltd.
-9-