Professional Documents
Culture Documents
AdBlue Caution
1. The first warning level is entered
when the estimated AdBlue range
General information is between 1500 miles and
Avoid contact of the paintwork with 500 miles.
The selective catalytic reduction AdBlue.
(BlueInjection) is a method to When switching on the ignition,
In case of contact, rinse off with this warning will show up once
substantially reduce the nitrogen water.
oxides in the exhaust emission. This briefly with the calculated range.
is achieved by injecting a Diesel Additionally, control indicator
AdBlue freezes at a temperature of B will illuminate and a chime
Exhaust Fluid (DEF) into the exhaust approx. -11 °C. As the vehicle is
system. The ammonia released by will sound. Driving is possible
equipped with an AdBlue pre-heater, without any restrictions.
the fluid reacts with nitrous gases the emissions reduction at low
(NOx) from the exhaust and turns it temperatures is ensured. The AdBlue 2. The next warning level is entered
into nitrogen and water. pre-heater works automatically. when the estimated AdBlue range
The designation of this fluid is is below 500 miles. The message
Notice with the current range will always
AdBlue®. It is a non-toxic, non- Frozen and again liquefied AdBlue is be displayed when ignition is
flammable, colourless and odourless usable without quality loss. switched on. Additionally, control
fluid which consists of 32% urea and
The typical AdBlue consumption is indicator B will flash and a
68% water.
approx. 2 l per 600 miles, but can also chime will sound. Refill AdBlue
be higher depending on driving before entering the next warning
9 Warning level.
behaviour (e.g. high load or towing).
Avoid contact of your eyes or skin 3. The next warning level is entered
Level warnings with a range below 60 miles. The
with AdBlue.
Depending on the calculated range of message with the current range
In case of eye or skin contact,
AdBlue, different messages are will always be displayed when
rinse off with water.
displayed in the Driver Information ignition is switched on.
Centre. The messages and the Additionally, control indicator
restrictions are a legal requirement. B will flash and a chime will
sound. Refill AdBlue as soon as
Driving and operating 133
possible before the AdBlue tank is Follow the instructions of the warning sealed refill adapter for refilling, to
completely empty. Otherwise, a messages. If starting is prevented, prevent splashback and overspill,
restart of the engine will not be seek the assistance of a workshop. and in order to ensure that the fumes
possible. from the AdBlue tank are captured
Refilling AdBlue and do not emerge.
4. The last warning level is entered
when the AdBlue tank is empty. Since AdBlue has a limited
Restart of the engine is not Caution durability, check the date of expiry
possible. before refilling.
Only use AdBlue that complies
A message appears in the Driver with European standards Notice
Information Centre. Additionally, DIN 70 070 and ISO 22241-1. Refill the AdBlue tank to a level of at
control indicator B will flash least 10 l, to ensure that the new
and a chime will sound. Do not use additives. AdBlue level is being detected.
Refill the AdBlue tank completely, Do not dilute AdBlue. In case AdBlue refill is not
otherwise restarting of the engine Otherwise the selective catalytic successfully detected:
is not possible. reduction system could be 1. Continuously drive the vehicle
damaged. for ten minutes making sure that
High emission warnings
vehicle speed is always higher
In the event of a fault with the The AdBlue tank should be filled than 12 mph.
emissions control system, different completely. This must be done if the
warning message regarding 2. If AdBlue refill is detected
messages are displayed in the Driver successfully, AdBlue supply-
Information Centre. prevention of an engine restart is
already displayed. driven warnings or limitations will
The messages and the restrictions disappear.
are a legal requirement. The warning AdBlue refilling quantity 3 247.
If AdBlue refill is still not detected,
messages are accompanied by the Notice seek the assistance of a workshop.
control indicators u, C and W. Whenever a filling pump with a
nozzle for passenger cars is not If AdBlue must be refilled at
Additionally, a chime will sound.
available at a filling station, use only temperatures below -11 °C, the
AdBlue bottles or canisters with a refilling of AdBlue may not be
detected by the system. In this
134 Driving and operating
event, park the vehicle in a space Notice
with a higher ambient temperature Dispose of AdBlue canister
until AdBlue is liquified. according to environmental
requirements. Hose can be reused
Notice
after flushing with clear water before
When unscrewing the protective cap
AdBlue dries out.
from the filler neck, ammonia fumes
may emerge. Do not inhale as the
fumes have a pungent smell. The
fumes are not harmful by inhalation.
The vehicle must be parked on a level
surface.
The filler neck for AdBlue is located 4. Unscrew protective cap from the
behind the fuel filler flap. filler neck.
The fuel filler flap can only be opened 5. Open AdBlue canister.
if the vehicle is unlocked.
6. Mount one end of the hose on the
1. Switch off the ignition. canister and screw the other end
2. Close all doors to avoid ammonia on the filler neck.
fumes entering the interior of the 7. Lift the canister until it is empty, or
vehicle. until the flow from the canister has
3. Release the fuel filler flap by stopped.
pushing the flap 3 195. 8. Place the canister on the ground
to empty the hose, wait
15 seconds.
9. Unscrew the hose from the filler
neck.
10. Mount the protective cap and turn
clockwise until it engages.
Driving and operating 135
Gear selection selector will return to the centre The vehicle automatically shifts into
position.The selected mode is P when
indicated in the Driver Information ● the ignition is switched off
Centre.
● the driver's door is opened while
Park position P the vehicle's speed is below
3 mph
9 Warning If the ignition is switched off while N is
selected, the vehicle shifts into P after
Do not leave the vehicle when the
a delay of approx. five seconds.
propulsion system is running, the
vehicle may move suddenly. You To avoid that the vehicle shifts from N
or others can be injured. To be into P, enable free wheeling:
sure the vehicle will not move, With the vehicle stationary and the
even if you are on even ground, engine running, depress the brake
Move the selector or press the make sure the parking brake is pedal and select N.
respective buttons. applied and P is selected. Within 5 seconds do the following:
P : park position, front wheels are 1. Depress and hold the brake
blocked, engage only when the To shift into P, press button P.
pedal.
vehicle is stationary To shift out of P, depress the brake
R : reverse gear, engage only when pedal and select the desired mode. 2. Switch off the ignition and move
the vehicle is stationary the selector forwards or
The vehicle will not shift into P if it is backwards.
N : neutral moving too fast. Stop the vehicle and
D : automatic mode shift into P. 3. Take your foot off the brake pedal
M : manual mode and switch on the ignition.
4. Depress and hold the brake pedal
Shifting and push the electric parking
Shifting always starts from a centre brake to release it.
position and is operated by moving 5. Take your foot off the brake pedal
the selector. Once operated, the and switch off the ignition.
Driving and operating 139
A message is displayed in the Driver Automatic mode D Manual mode
Information Centre indicating that the
Notice Manual mode M can be activated in
wheels are unblocked for the next 15 In slippery conditions, operate the each driving situation and speed
minutes. vehicle in D for enhanced riding and when D is selected.
To revert to normal operation, handling performance.
depress the brake pedal and switch The selected gear is indicated in the
on the engine. Manual mode M Driver Information Centre.
In this mode, it is possible to change If a higher gear is selected when
Parking brake 3 143. gears manually using steering wheel vehicle speed is too low, or a lower
Reverse gear R paddles. gear when vehicle speed is too high,
To shift into and out of R, the vehicle Manual mode 3 139. the shift is not executed. This can
must be at standstill and the brake cause a message in the Driver
pedal has to be depressed. Engine braking Information Centre.
Neutral N To utilise the engine braking effect, In manual mode, no automatic
In this mode, the propulsion system select a lower gear in good time when shifting to a higher gear takes place
does not transfer torque to the driving downhill. at high engine revolutions.
wheels. To restart the propulsion Manual mode 3 139.
system when the vehicle is already
moving, use D only. Deactivation of the automatic
When N is selected, P is engaged operation of park position P and of
after a short time. electric parking brake
If the driver's door is opened while N For this procedure, refer to the
is selected, an audible signal is given description of the automatic parking
and P is engaged. The audible signal brake.
stops when the driver's door is closed.
Parking brake 3 143
140 Driving and operating
Press button M. Special programmes automatically Have the cause of the fault remedied
Pull steering wheel paddles to select adapt the shifting points when driving by a workshop.
gears manually. up inclines or down hills.
Pull right paddle + to shift to a higher In snowy or icy conditions or on other Interruption of power supply
gear. slippery surfaces, the electronic
In the event of an interruption of
transmission control enables the
Pull left paddle - to shift to a lower power supply, it is not possible to
driver to select manually first, second
gear. select another mode when P is
or third gear for starting off.
Multiple pulls allow gears to be selected.
skipped. Kickdown Towing the vehicle 3 230.
Pressing down the accelerator pedal If the vehicle battery is discharged,
Gear shift indication start the vehicle using jump leads
beyond the kickdown detent will lead
The symbol Y or Z with a number to maximum acceleration 3 228.
beside it is indicated when independent of selected driving If the vehicle battery is not the cause
gearshifting is recommended for fuel mode. The transmission shifts to a of the fault, seek the assistance of a
saving reasons. lower gear depending on engine workshop.
Shift indication appears only in speed.
manual mode.
Fault
Electronic driving In the event of a fault, C illuminates
programmes a message is displayed in the Driver
Information Centre.
Following a cold start, the operating
temperature programme increases Vehicle messages 3 89.
engine speed to quickly bring the Electronic transmission control
catalytic converter to the required enables only third gear. The
temperature. transmission no longer shifts
automatically.
Do not drive faster than 62 mph.
Driving and operating 141
Caution
It is not advisable to drive with the
hand resting on the selector lever.
Cruise control Switching on the system Press OK to store the current vehicle
speed as speed setting and activate
The cruise control can store and the cruise control. / changes from
maintain speeds above 25 mph. For
grey to green indicating that system is
vehicles with manual transmission,
active. The accelerator pedal can be
any gear has to be selected. For
released.
vehicles with automatic transmission,
position D or the second or a higher Alternatively, move the thumb wheel
gear in position M must be selected. to - to increase or ! to decrease
Deviations from the stored speeds the speed and store this speed as
may occur when driving uphill or speed setting. Cruise control is
downhill. immediately activated if the
thumbwheel is moved upwards or
The system maintains the vehicle downwards. / changes from grey to
speed at the preset speed by the green.
driver, without any action on the Press /.
accelerator pedal. Setting speed by the driver
The preset speed can be exceeded
temporarily by pressing the
accelerator pedal firmly.
The status and preset speed is
displayed in the Driver Information
Centre.
Do not use the cruise control if it is not The cruise control screen is
advisable to maintain a constant displayed. / is grey indicating that
speed. the system is still not active.
Activation of the functionality
If all operating conditions are met,
OK? is displayed.
Driving and operating 149
If the system is active, the preset Cruise control is deactivated, but not
speed can be changed by moving the switched off. Last stored speed
thumb wheel to - to increase remains in memory for later speed
or ! to decrease the speed. Move resume.
thumb wheel repeatedly to change The cruise control may be
speed in small steps, move and hold deactivated automatically in the
to change speed in large steps. following cases:
OK? is displayed
Adopting speed by the speed limit Press OK to store the suggested ● brake pedal depressed
recognition speed. ● traction control system or
A detected speed limit can be used as The suggested speed is shown as electronic stability control is
new set speed for the cruise control. new speed setting. operating
To detect speed limit sign, the traffic ● reverse gear engaged, N
sign assistant has to be activated. Exceeding the set speed selected or no gear engaged
Traffic sign assistant 3 175. It is always possible to drive faster ● clutch pedal depressed for more
When passing the speed limit sign than the set speed by depressing the than five seconds
OK? is automatically displayed. accelerator pedal. When the ● electric parking brake engaged
Press OK on the steering wheel to accelerator pedal is released, the
store the suggested speed. vehicle returns to the stored speed. Resume stored speed
The suggested speed is shown as While the set speed is exceeded, the Press "
new speed setting. set speed setting flashes.
Switching off the system
After passing the speed limit sign Deactivation of the functionality
Press OK on the steering wheel. Press /, the cruise control mode is
Press ". The vehicle is driven deselected and the cruise control
without cruise control. screen is hidden from the Driver
Information Centre.
150 Driving and operating
System limitations Fault Switching on the system
Never use the system in the following The speed limit recognition may not
situations: operate correctly if traffic signs do not
● In an urban area with the risk of comply with the Vienna Convention
pedestrians crossing the road. on Road Signs and Signals.
● In heavy traffic (except versions In the event of a cruise control fault,
with the Stop & Go function). the speed is cleared resulting in
flashing of the dashes.
● On winding or steep roads.
Have the system checked by a
● On slippery or flooded roads. workshop.
● In poor weather conditions.
● In the event of restricted visibility Speed limiter
for the driver.
The speed limiter prevents the Press ..
● Driving on a speed circuit. vehicle from exceeding a preset
● Driving on a rolling road. maximum speed.
● When using snow chains, non- The maximum speed can be set at
slip covers or studded tyres. speeds above 18 mph.
When driving down a steep hill, the The driver can accelerate the vehicle
system cannot prevent the vehicle up to the preset speed. Deviations
from exceeding the set speed. Brake from the limited speed may occur
if necessary. when driving downhill. The speed limiter screen is
When driving up a steep hill or when displayed. . is grey indicating that
towing, the set speed may not be the system is still not active.
reached or maintained.
Driving and operating 151
Activation of the functionality Adopting speed by the speed limit Exceeding the speed limit
recognition
Press OK or " to activate the speed A detected speed limit can be used as In the event of an emergency, it is
limiter and store the current vehicle new set speed for the speed limiter. possible to exceed the speed limit by
speed as speed setting. . is To detect speed limit signs, the traffic depressing the accelerator pedal
illuminated in green. sign assistant has to be activated. firmly to the final point. In this case,
the preset speed value flashes.
Setting speed by the driver Traffic sign assistant 3 175.
Release the accelerator pedal and
When passing the speed limit sign the speed limiter function is
OK? is automatically displayed. reactivated once a speed lower than
the limit speed is obtained.
When exceeding the preset speed is
not caused by depressing the
accelerator pedal, e.g., when driving
down a steep slope, an audible signal
is given.
Press OK on the steering wheel to 9 Warning
store the suggested speed.
The suggested speed is shown as On a steep descent or in the event
new speed setting. of sharp acceleration, the speed
The preset speed can be changed by
After passing the speed limit sign limiter will not be able to prevent
moving the thumb wheel to - to
Press OK on the steering wheel. the vehicle from exceeding the
increase or ! to decrease the preset speed. If necessary,
speed. Move thumb wheel repeatedly OK? is displayed. depress the brake pedal to control
to change speed in small steps, move Press OK to store the suggested the vehicle's speed.
and hold to change speed in large speed.
steps.
The suggested speed is shown as
new speed setting.
152 Driving and operating
Deactivation of the functionality In the event of a speed limiter fault, The adaptive cruise control
the speed is cleared resulting in automatically decelerates the vehicle
Press ", speed limiter is in pause flashing of the dashes. when approaching a slower moving
mode and a message is displayed. vehicle. It then adjusts the vehicle
Have the system checked by a
The vehicle is driven without speed speed to follow the vehicle ahead at
workshop.
limiter. the selected following distance. The
Speed limiter is deactivated, but not vehicle speed increases or decreases
switched off. Last stored speed Adaptive cruise control to follow the vehicle ahead, but will
remains in memory for later speed The adaptive cruise control is an not exceed the set speed. It may
resume. enhancement of the cruise control apply limited braking with activated
with the additional feature of brake lights.
Resume limit speed maintaining a certain following If the vehicle ahead accelerates or
Press ", the stored speed limit will be distance to the vehicle ahead. changes lane, the adaptive cruise
obtained. control progressively accelerates the
vehicle to return to the stored set
Switching off the system speed. If the driver operates the turn
lights to overtake a slower vehicle, the
Press ., the speed limiter mode is adaptive cruise control allows the
deselected and the speed limiter vehicle to temporarily approach the
screen is hidden from the Driver vehicle ahead to help passing it.
Information Centre. However, the set speed will never be
It uses a camera located at the top of
the windscreen and a radar unit exceeded.
Fault
located in the front bumper to detect If the vehicle ahead is moving too
The speed limit recognition may not the vehicles ahead. If no vehicle is slowly and the selected following
operate correctly if traffic signs do not detected in the driving path, the distance cannot be maintained
comply with the Vienna Convention adaptive cruise control behaves like a anymore, a warning chime is given
on Road Signs and Signals. conventional cruise control. and a message is displayed. The
message prompts the driver to take
back control of the vehicle. On
Driving and operating 153
vehicles with manual transmission, ● drivers's seat belt fastened
the system can brake the vehicle until ● D selected or second or higher
19 mph. On vehicles with automatic gear engaged
transmission, the system can brake
the vehicle until a full stop. Depending ● parking brake released
on version, the system can ● brake pedal depressed if vehicle
automatically accelerate the vehicle stationary
after a full stop.
Activation of the functionality
9 Warning If all operating conditions are met,
OK? is displayed.
The brake lamps come on if the
vehicle is slowed down by active
emergency braking. Press , successively until the
adaptive cruise control mode is
If the brake lights fail, the system selected.
does not operate.
The adaptive cruise control screen is
displayed. The system is still not
Switching on the system
activated.
Press OK to store the current vehicle
Press _ and make sure the Drive
Operation conditions speed and activate the cruise control.
Assist is activated in the Info Display. On the adaptive cruise control
The system can be activated if the screen, the set speed and a road
following conditions are met: element are displayed in green. The
● vehicle speed between 19 mph accelerator pedal can be released.
and 112 mph for vehicles with Alternatively, move the thumb wheel
manual transmission, between to - to increase or ! to decrease
0 mph and 112 mph for vehicles the speed and store this speed. The
with automatic transmission cruise control is immediately
● driver's door closed activated if the thumbwheel is moved
154 Driving and operating
upwards or downwards. On the Adopting speed by the speed limit Exceeding the set speed
adaptive cruise control screen, the recognition
set speed and the road element are A detected speed limit can be used as It is always possible to drive faster
displayed in green. new value for the adaptive cruise than the set speed by depressing the
control. accelerator pedal. When the
Setting speed by the driver accelerator pedal is released, the
When passing the speed limit sign vehicle returns to the stored speed. If
OK? is automatically displayed. a slower moving vehicle is ahead, the
Press OK on the steering wheel to following distance selected by the
store the suggested speed. driver is restored.
The suggested speed is shown as While the set speed is exceeded, the
new speed setting. set speed flashes on the adaptive
cruise control screen.
After passing the speed limit sign
Press OK on the steering wheel.
9 Warning
Accelerating by the driver
deactivates automatic braking by
the system. This is indicated as a
The set speed can be changed by pop-up warning in the Driver
moving the thumb wheel to - to Information Centre.
increase or ! to decrease the
OK? is displayed Resuming stored speed
speed. Move thumb wheel repeatedly
to change speed in small steps, move Press OK to store the suggested
and hold to change speed in large speed. Press " or OK to reactivate the
steps. adaptive cruise control at the stored
The suggested speed is shown as
speed.
new speed setting.
Traffic sign assistant 3 175.
Driving and operating 155
Adaptive cruise control on Within three seconds after the vehicle selector lever to park position P
vehicles with automatic has been stopped by the system, the and switch off the ignition before
transmission vehicle slowly moves again. After leaving the vehicle.
three seconds, accelerate or
For vehicles with automatic depress . to drive away. Pay
transmission, the adaptive cruise Setting the following distance
attention to the surroundings of the
control allows to maintain the vehicle when driving away. When the adaptive cruise control
selected distance behind a braking detects a slower moving vehicle in the
If the vehicle stays stopped for more
vehicle until a complete stop is driving path, it will adjust the vehicle
than five minutes without any action
reached. speed to maintain the following
of the driver, the electric parking
If the system has stopped your brake is applied. Control indicator distance selected by the driver.
vehicle behind another vehicle, the j will illuminate. To release electric The following distance can be set to
green control indicator . is parking brake, press the accelerator close (1 bar), normal (2 bars) or far (3
displayed to the left of the set speed pedal. bars).
setting. This symbol notifies, that the If the engine is running and the
Electric parking brake 3 143.
vehicle is hold automatically in stop adaptive cruise control is switched on
position. (grey) or active (green), you can
9 Warning
While the vehicle is hold in stop modify the following distance setting:
position, the following When the system is deactivated or
recommendations should be cancelled, the vehicle will no
followed: longer be held at a stop and can
● Do not leave the vehicle. start moving. Be always prepared
● Do not open the load to manually apply the brake to hold
compartment. the vehicle stationary.
● Do not engage the reverse gear. Do not leave the vehicle while it is
being held at a stop by adaptive
● Do not drop off or pick up cruise control. Always move
passengers.
156 Driving and operating
Active emergency braking The system uses a camera located at Activating / deactivating the
the top of the windscreen and system
Active emergency braking can help to depending on version a radar unit
reduce the damage and injury from a located in the front bumper to Active emergency braking is
crash with a preceding vehicle, with a calculate the probability of a frontal activated / deactivated in the Info
cyclist or with a pedestrian when the collision. Display.
driver does not actively take action
either by manual braking or by
steering. Before active emergency
9 Warning
braking applies, the driver is warned
This system is not intended to
by the forward collision alert.
replace the driver responsibility for
The system includes the following driving the vehicle and looking
functions: ahead. Its function is limited to
● forward collision alert supplemental use only to reduce
● smart brake assist the vehicle speed before a
collision.
● automatic emergency braking
The system may not react to
animals. After a sudden lane
change, the system needs a
certain time to detect the next Press _ and activate / deactivate the
preceding vehicle. system in the Info Display.
The driver must always be ready Info Display 3 86.
to take action and apply the brakes If deactivated, m illuminates in the
and steer to avoid collisions. Driver Information Centre. When
ignition is switched on next time, the
system is activated by default.
160 Driving and operating
Functionality ● Level 2: A warning message is safety, but increases the amount of
displayed in the Driver alerts if the legal safety distance is
When a moving vehicle has been Information Centre and a warning not kept. To reduce the number of
detected, active emergency braking chime sounds, when a collision is alerts, select a shorter alert
operates from 6 mph to 53 mph for imminent and immediate driver's sensitivity setting.
vehicles with camera, from 6 mph to action is required.
87 mph for vehicles with camera and Three alert sensitivities can be
radar. ● Level 3: Depending on version, selected in the driver assistance
the vehicle may produce a short systems menu.
When a stationary vehicle, a cyclist or brake jerk to confirm the risk of
a pedestrian has been detected, Vehicle personalisation 3 91.
collision. The immediate driver's
active emergency braking operates if action is required. The chosen setting will be memorised
the vehicle speed does not exceed when the ignition has been switched
50 mph. off. The alert sensitivity will vary
9 Warning
based on selected alert setting.
Forward collision alert
When approaching a vehicle
The forward collision alert warns the
Smart brake assist
ahead too rapidly, a level 2 alert
driver if there is a risk of collision with may be displayed without a level 1 If the driver brakes, but not sufficiently
the vehicle ahead, with a cyclist or a alert before. to avoid a collision, this system will
pedestrian. Level 1 alerts depend on the alert supplement the braking. This
sensitivity set. This alert type is assistance will only be provided if the
Alerting the driver driver presses the brake pedal.
only displayed in case of moving
The driver is warned by following
vehicles. At lower speed it is Smart brake assist will automatically
alerts:
disabled. disengage when the brake pedal is
● Level 1: A warning message is released.
displayed in the Driver
Selecting the alert sensitivity
Information Centre, when the Automatic emergency braking
distance to the vehicle ahead Notice
gets too small. If the alert sensitivity setting with the This function intervenes after the
longest distance is set, the system warning chime if the driver does not
warns earlier. This increases the operate the brake pedal quickly
Driving and operating 161
enough. The system tries to reduce certain time. Keep the brake ● the vehicle speed is between
the impact speed of the collision or to pedal depressed to prevent the 3 mph and 50 mph
avoid a collision if the driver fails to vehicle from starting off again. ● the pedestrian has been enough
react. ● Manual transmission: If the time in the capturing fields of the
If automatic emergency braking is vehicle comes to a complete sensors
applied, m flashes in the Driver stop, the engine may stall. Keep ● visibility is sufficient for the
Information Centre. the brake pedal depressed to sensors to detect the pedestrian
Below a speed of 19 mph, automatic prevent the vehicle from rolling.
emergency braking may slow down Cruise control and adaptive cruise Operation conditions
the vehicle to a complete stop. Else, control will be deactivated when an The system requires the following
the speed will be reduced by a emergency automatic braking occurs. operating conditions:
maximum of 16 mph. For versions
● vehicle moving forward without
with camera and radar, the speed 9 Warning
reduction may be extended to trailer
31 mph if both sensors are able to Do not rely on the system to brake ● brake system operational
detect the hazard. the vehicle. Automatic emergency ● Electronic Stability Control and
The driver must apply the brake to braking will not brake outside of its Traction Control activated
come to a complete stop. operating speed range and only
● seat belts fastened on all seats
responds to detected vehicles and
● Automatic transmission: If the pedestrians. ● constant speed on roads with no
vehicle comes to a complete or low curvature
stop, automatic emergency ● the corresponding turn light is
braking is maintained for a activated in advance
● the vehicle speed is between
3 mph and 12 mph
● the vehicle is about to cross the
driving path of another vehicle
162 Driving and operating
System limitations ● following an impact to the In rare cases such as sensor
windscreen close to the camera initialisation, board voltage out of
The system is automatically regular range etc., the system may
deactivated in the following ● following a front bumper
deformation, e.g. during parking not be available or may operate in a
situations: degraded mode. This is not indicated
● diameter of the spare wheel too ● attaching a trailer, particularly to the driver.
small trailers without own braking
system If a fault occurs, m illuminates, a
● fault with the brake pedal or with message indicating the fault is
a brake light detected ● driving with snow chains
displayed and an audible signal is
● fault in the sensors, in the Fault given. Seek the assistance of a
electronic or in the brake system workshop.
detected If the system is not available due to If m and C are displayed after
system limits or operating conditions,
● trailer with an electrical plug having the engine switched off and
m illuminates in the Driver
connection detected restarted, seek the assistance of a
Information Centre. workshop.
● following an impact (e.g.
In certain cases, m illuminates If at least one seat belt of the front
collision). Have the system
checked by a workshop. accompanied by a message that the seats is not fastened, m and a
sensor is blind. For vehicle equipped illuminate. The system is deactivated
We recommend to deactivate the only with camera, the system is
system in any situation in which the until all seat belts are fastened.
deactivated. For systems equipped
ignition is switched on and active with camera and radar, the system Vehicle messages 3 89.
emergency braking represents a risk may operate in a degraded mode.
such as: This may be caused by reduced Automatic post collision
● carrying long objects on roof bars visibilty due to weather conditions or
by an actual blockage of the sensor.
braking
● using an automatic car wash
In this case, verify whether the If an accident is detected, the vehicle
● placing the vehicle on a roller camera or the radar unit are blocked requests automatic post collision
bench in a workshop by dirt or other foreign objects. braking. The goal of this function is to
● towing the vehicle reduce the risk of further collisions if
Driving and operating 163
the driver does not react. The Fault
automatic post collision braking is not 9 Warning
operational if the capability of the If automatic post collision braking is
vehicle to trigger and execute the not available, the control indicator J The system does not adapt the
automatic post collision braking is or d illuminates continuously, a vehicle speed in curves which are
unavailable, as it can occur in corresponding message appears in too tight, e.g. hairpin curves.
destructive accidents or in other the Driver Information Centre and a
specific accident scenarios. warning chime sounds. Operation conditions
It is possible to override the automatic Have the cause of the fault remedied Curve speed adaption is ready to
braking by pressing the accelerator by a workshop. operate if the following conditions are
pedal or the brake pedal. met:
System limitations Curve speed adaptation ● The vehicle speed is between
The system adapts the vehicle speed 43 mph and 112 mph.
The system operates if the following within its lane before entering a curve ● The Drive Assist is activated.
conditions are fulfilled: or when already driving in the curve. ● The vehicle is driving on road
● airbags or seat belt pretensioners The vehicle speed is only adapted if it with separate carriageways a
have been deployed by the is too fast for the angle of the curve. If such as a motorway or
collision a vehicle is ahead, the following expressway.
● braking system and electric distance to this vehicle is mantained.
functions remain continuously The driver can overrule the system by Activation
operational during and after depressing the brake pedal or the Curve speed adaption is activated via
collision accelerator pedal: Drive Assist.
● driver has not depressed brake ● Depressing the accelerator pedal
pedal or accelerator pedal temporarily pauses the function.
● Depressing the brake pedal
deactivates the function.
164 Driving and operating
Press , at the steering wheel Parking assist
successively until the Drive Assist
mode is selected. General information
The Drive Assist screen is displayed
in the Driver Information Centre. 9 Warning
Info Display 3 86.
The driver bears full responsibility
Operation for the parking manoeuvre.
Always check the surrounding
The system monitors the curves. If it
area when driving backwards or
detects that the current vehicle speed
forwards while using parking
is not compatible with the angle of the
assist system.
curve, it adapts the speed gradually.
Press _ and activate Drive Assist in
the Info Display. Deactivation Front-rear parking assist
Press , successively until the mode The front-rear parking assist
to switch off assistance is selected. measures the distance between the
vehicle and obstacles in front and
behind the vehicle. It warns of objects
in the vehicle's direction and in the
detection zone of the sensors by
giving acoustic signals and display
indication.
Driving and operating 165
The system operates with ultrasonic Indication more than three seconds in a forward
parking sensors in the rear and front As soon as an obstacle gets closer to gear or the obstacle is no longer
bumper. the vehicle, you will hear acoustic detected.
warning signals. If the vehicle is electrically connected
Activation
to a trailer, a bicycle carrier etc., the
rear assist is automatically
deactivated. In this case, the outline
of a trailer is displayed at the rear part
of the vehicle in the Driver Information
Centre.
To manually deactivate the system,
press _ and deactivate the system
in the Info Display. e will illuminate in
the Driver Information Centre.
System limitations
The interval between the sounds In the event of a fault or if the system
Press _ and activate Close becomes shorter as the vehicle gets does not work temporarily, e.g.
Obstacle Detection. closer to the obstacle in the driving because of high external noise level
Once activated, the system is ready direction. When the distance is less or other interference factors, C
to operate when e is not shown in the than approx. 30 cm, the sound is illuminates in the Driver Information
Driver Information Centre. continuous. Centre, e illuminates in the Driver
Information Centre, a message is
The front parking assist is triggered Deactivation displayed and a warning chime
when an obstacle is detected in front The system is deactivated sounds.
and the speed of the vehicle is below automatically if vehicle speed
6 mph. The rear parking assist is exceeds 6 mph, the vehicle stops for
triggered, when the reverse gear is
engaged.
166 Driving and operating
Notice Performance of the parking assist The system displays a visual alert in
Make sure that the front number system can be reduced due to each exterior mirror when detecting
plate is properly mounted, vertically heavy loading. objects that may not be visible in the
and horizontally centred and the interior and exterior mirrors.
sensors are firmly in place. The Special conditions apply if there
are taller vehicles in the vicinity Side blind spot alert uses two radar
performance of the parking assist sensors located in the rear bumper on
will be reduced if the license plate is (e.g. off-road vehicles, mini vans,
vans). Object identification and each side of the vehicle.
bent or a license plate support is
used. correct distance indication in the
upper part of these vehicles 9 Warning
9 Warning cannot be guaranteed.
Damage or scratches on the
Objects with a very small reflection vehicle surface near the radar
Under certain circumstances, cross-section, e.g. objects of sensors may affect the
various reflective surfaces on narrow size or soft materials, may performance of the system. This
objects or clothing as well as not be detected by the system. can cause wrong warnings or the
external noise sources may cause Parking assist systems do not loss of warnings.
the system to fail to detect detect objects outside the
obstacles. Seek the assistance of a
detection range. workshop.
Special attention must be paid to
low obstacles which can damage Side blind spot alert
the lower part of the bumper. 9 Warning
The side blind spot alert system
detects and warns of vehicles Side blind spot alert is only a lane
Caution approaching from the rear in changing aid and does not replace
neighbouring lanes up to 75 m or of driver vision.
Performance of the system can be another vehicle in the blind spot of the
reduced when sensors are vehicle. Side blind spot alert does not
covered, e.g. by ice or snow. detect:
Driving and operating 167
● Vehicles approaching very Press _ and activate / deactivate the The LED comes on immediately when
rapidly. system in the Info Display. your vehicle is being passed.
● Pedestrians or animals. When the system is activated and the The LED comes on after a delay when
engine is switched on, the LEDs in your vehicle is passing another
● Non-moving objects, e.g. each exterior mirror come on to vehicle slowly.
stationary vehicles, street indicate the system's activation.
lights, road signs, etc. Operation conditions
Info Display 3 86.
Failure to use proper care when The following conditions have to be
changing lanes may result in Functionality fulfilled:
damage to the vehicle, injury, or
death. Always check the outside ● all vehicles moving in the same
and rearview mirrors, glance over direction and in adjacent lanes
your shoulder, and use the turn ● passing a vehicle with a speed
signal before changing lanes. difference of less than 9 mph
● normal traffic flow
Activation ● vehicle not pulling a trailer
● sensors not covered by mud, ice,
snow etc.
● LEDs in the door mirrors or the
rear radars not covered with
stickers or other objects
When the system detects a vehicle in
the side blind zone while driving
forwards, an LED will illuminate in the
relevant exterior mirror. If the turn
lights of the relevant side are
activated, the LED will flash.
168 Driving and operating
No alert will be given in the following Deactivation camera view area, e. g. below the
situations: bumper, or underneath the
Press _ and deactivate the system
● non-moving objects, e.g. parked vehicle.
in the Info Display.
vehicles, barriers, street lamps, Do not drive or park the vehicle
road signs The system is automatically
deactivated when the vehicle is using only the panoramic view
● in very dense traffic, when system.
electrically connected to a trailer,
moving vehicles might be Always check the surrounding of
bicycle carrier, etc.
confused with a stationary object the vehicle before and during
● vehicles moving in the opposite Fault driving.
direction Displayed images may be further
In the event of a fault, C illuminates
● passing too quickly in the instrument panel and a or closer than they appear. The
The function will not work properly message is displayed. Seek the area displayed is limited and
due to adverse weather conditions assistance of a workshop. objects that are close to either
such as heavy rain, damage of the edge of the bumper or under the
surface near the radar sensor or bumper are not displayed on the
when the sensors are covered with
Panoramic view system screen.
mud / dirt from the road. This system allows views of the
vehicle's surroundings to be
Caution displayed as a full 360° picture in the
Info Display, like a bird's eye view.
If the rear bumper is to be
repainted or repaired, contact a 9 Warning
workshop. Certain types of paint
could interfere with the operation The panoramic view system does
of the radars. not replace driver vision. It will not
display children, pedestrians,
cyclists, crossing traffic, animals,
or any other objects outside of the
Driving and operating 169
The system uses: ● two side cameras in the exterior Activation
mirrors
The panoramic view system is
● ultrasonic parking sensors in the activated by:
bumpers
● engaging the reverse gear when
Visualisation on the Info Display the engine is switched on
● manual activation in the Info
Display when the vehicle speed
is below 10 mph
Info Display 3 86.
Functionality
The screen is divided into four areas,
● rear camera from left to right:
● selectable views: standard,
panoramic front, panoramic rear
● view visualisation
● top view including four selectable
side views (in standard view only) Different views can be selected in the
● settings : left part of the display. Change the
type of view at any time during a
The parking sensors complete the manoeuvre by selecting a view from
information on the view from above the left side:
the vehicle.
● standard view
● panoramic view
● front camera ● side view
170 Driving and operating
The display is immediately updated Front view Side view
with the type of view selected. The area in front the vehicle is This view allows to view the
By default, the zoom view is enabled. displayed in the screen. The vertical surroundings, e.g. a pavement, a low
This setting can be changed in the lines represent the width of the wall, the vehicle parked to the next
settings of the panoramic view vehicle with mirrors unfolded. The etc. on the left-hand or right-hand side
system in the Info Display. direction of the lines changes with the of the vehicle.
steering angle. Select the standard view and touch
The state of the system is kept in
memory when the ignition is switched The first horizontal line represents a the required side of the vehicle. The
off. distance of about 30 cm beyond the selected side is highlighted and the
edge of vehicle's front bumper. The side view is displayed.
Standard view upper horizontal lines represent
The standard view consists of a rear distances of about 1 m and 2 m. Zoom view
view and a front view. This view is displayed automatically The zoom view cannot be selected. It
or can be chosen from the left side of is only displayed if the distance
Rear view
the screen. between the vehicle and the obstacle
The area behind the vehicle is
is less than 60-80 cm.
displayed in the screen. The vertical
lines represent the width of the Panoramic view The zoom provides a view from above
vehicle with mirrors unfolded. The The panoramic view facilitates the rear or the front of the vehicle in
direction of the lines changes with the leaving a parking bay, making it its near surroundings.Thus, the
steering angle. possible to see the approach of vehicle can be manoeuvred around
vehicles, pedestrians and cyclists. obstacles nearby.
The first horizontal line represents a This view is not recommended for
distance of about 30 cm beyond the The automatic display of the zoom
carrying out a complete manoeuvre. view can be disabled in the Info
edge of vehicle's rear bumper. The This view can only be selected from
upper horizontal lines represent Display:
the left side of the screen.
distances of about 1 m and 2 m. Press _ below the Info Display and
This view is available in auto mode or select Panoramic camera.
can be chosen from the left side of the Press :.
screen.
Activate View Adaptation.
Driving and operating 171
The setting is memorised when the there is a washer nozzle which will Rear view camera
ignition is switched off. be activated when the rear window The rear view camera assists the
Settings washer is operating. driver when reversing by displaying a
If manually cleaning the lenses of view of the area behind the vehicle. It
The following settings can be the cameras, rinse the lenses with allows views of the vehicle's
adjusted: water and wipe with a soft cloth. surroundings to be displayed as a
● volume of the audible signal Do not clean the lenses with a nearly 180° picture in the Info Display,
● brightness steam-jet or high-pressure jet like a bird's eye view.
● contrast cleaner.
9 Warning
Deactivation The panoramic view system may not
operate properly when: The rear view camera does not
Panoramic view system is replace driver vision. Note that
deactivated when: ● The surrounding is dark. objects that are outside the
● driving faster than 10 mph in ● The sun or the beam of camera's field of view and the
forward gear headlights is shining directly into parking assist sensors, e.g. below
the camera lenses. the bumper or underneath the
● by pressing the icon X in the left
● Weather limits visibility, such as vehicle, are not displayed.
upper corner of the touch screen
fog, rain, or snow. Do not reverse or park the vehicle
System limitations ● The camera lenses are blocked using only the rear view camera.
by snow, ice, slush, mud, dirt. Always check the surrounding of
Caution ● The vehicle is towing a trailer. the vehicle before and during
driving.
For optimal operation of the ● The vehicle had an accident.
system, it is important to keep the ● There are extreme temperature
lenses of all cameras always changes.
clean. For the rear view camera,
172 Driving and operating
The system uses: The parking sensors complete the Change the type of view at any time
information on the view from above during a manoeuvre by selecting the
the vehicle. required view from the view selection
The area displayed by the rear view in the left part of the Info Display:
camera is limited. Displayed images ● Standard view
may be further or closer than they ● 180° view
appear.
The display is immediately updated
The system automatically selects the with the type of view selected.
best view to display according to the
information from the parking sensors. Using the camera, the vehicle's close
The state of the system is not kept in surroundings are recorded during low
memory when the ignition is switched speed manoeuvres. An image from
off. above the vehicle in its close
surroundings is created in real time
● rear view camera, mounted in the (on the side of the screen), as the
rear bumper above the number
Activation
vehicle progresses. This view makes
plate The rear view camera is activated it easier to align the vehicle when
● ultrasonic parking sensors in the when the reverse gear is engaged. parking and to perceive nearby
rear bumper obstacles. It is automatically deleted
Functionality if the vehicle remains stationary for
The screen in the Info Display is
divided into three parts: too long.
● On the right side, there is a view Standard view
from above the vehicle. The area behind the vehicle is
● The middle part consists of a displayed in the screen. The vertical
contextual view. lines represent the width of the
● The left side consists of the view vehicle with mirrors unfolded. The
selection as well as the settings Different views can be selected in the direction of the lines changes with the
menu. left part of the display. steering angle.
Driving and operating 173
The first horizontal line represents a nearby. Zoom view cannot be System limitations
distance of about 30 cm beyond the manually selected. It is automatically
edge of vehicle's rear bumper. The activated if the distance between the Caution
upper horizontal lines represent vehicle and the obstacle is approx.
distances of about 1 m and 2 m. 60-80 cm. For optimal operation of the
This view is displayed automatically system, it is important to keep the
Settings menu
or can be chosen from the view lense of the camera, which is
selection. The settings menu allows to adjust located between the number plate
Trajectory lane of the vehicle is the following settings: lights, always clean. The rear view
shown in accordance with the ● volume of the audible signal camera can be cleaned by a
steering angle. washer nozzle which is
● brightness automatically activated when the
180° view ● contrast rear window washer is operating.
The 180° view facilitates reversing To wip away water drops from the
out of a parking bay, making it Deactivation lense, use a soft cloth.
possible to see the approach of The rear view camera is deactivated Do not clean the lense with a
vehicles, pedestrians and cyclists. when: steam-jet or high-pressure jet
This view is not recommended for ● driving faster than 6 mph in a cleaner.
carrying out a complete manoeuvre. forward gear
The rear view camera may not
Zoom view ● by pressing the icon X in the left operate properly when:
The rear view camera records the upper corner of the touch screen
● surrounding is dark
vehicle's surroundings during the
manoeuvre in order to reconstruct a ● sun or beam of headlights is
view from above the rear or the front shining directly into camera
of the vehicle in its near surroundings. lenses
An image from above the vehicle in its ● weather limits visibility, such as
close surroundings is created as the fog, rain, or snow
vehicle progresses. Thus, the vehicle
can be manoeuvred around obstacles
174 Driving and operating
● camera lenses blocked by snow, Notice Activation / deactivation
ice, slush, mud, dirt. Clean the If repainting the rear bumper,
lense, rinse with water, and wipe consult a qualified workshop since
with a soft cloth certain types of paint could interfere
● vehicle is electrically connected with the operation of the radar units.
to a trailer, bicycle carrier, etc. Additional to the side blind spot alert
● vehicle had a rear end accident 3 166, rear cross traffic alert warns of
● extreme temperature changes cross traffic from left or right side
when driving rearwards at a speed up
to 6 mph. It warns of approaching
Rear cross traffic alert objects such as vehicles, trucks,
pedestrians, cyclists and
Caution motorcycles.
To monitor the area left and right
The driver must monitor the behind the vehicle, the system uses Press _ and activate / deactivate the
surroundings before and during two radar sensors located in the rear system in the Info Display.
the whole manoeuvre. Drive bumper on each side of the vehicle. Info Display 3 86.
slowly and carefully in reverse
gear in case of reduced or no Detection zone
visibility.
It is possible that warnings are not
given, are given too late or seem
unjustified. Be prepared to react at
any time to avoid an accident.
Deactivation 9 Warning
The actual traffic sign always
takes priority over the traffic sign
displayed in the Driver Information
Press _ below the Info Display and Centre.
activate Drive Assist.
If the entry of a lane is forbidden by
the corresponding traffic sign and the
vehicle enters the lane in the wrong
direction, the traffic sign and a
message is displayed in the Driver
Information Centre.
Activation / deactivation
Press , successively until the mode
to switch off assistance is selected. Press _ and activate / deactivate the
system in the Info Display.
Other traffic signs
The system recognises traffic signs
and displays them in the Driver
Information Centre.
Driving and operating 177
System limitations If the vehicle approaches a road edge
Caution or a lane marking, the steering wheel
Traffic sign assistant may not operate is gently turned to position so that the
properly when: The system is intended to help the vehicle turns back into the lane. The
● Driving on winding or hilly roads. driver within a defined speed driver will then notice a turning
range to discern certain traffic movement of the steering wheel. Turn
● During nighttime driving. signs. Do not ignore traffic signs steering wheel in same direction, if
● Driving with snow chains. which are not displayed by the the system does not steer sufficiently.
● Driving with a trailer. system. Turn steering wheel gently into
● The area of the windscreen, The system does not discern any opposite direction, if lane change is
where the front camera is other than the conventional traffic intended.
located, is not clean or affected signs that might give or end a When the system steers to correct the
by foreign items, e.g. stickers. speed limit. trajectory of the vehicle, L flashes
● Weather limits visibility, such as Do not let this special feature yellow in the Driver Information
fog, rain, or snow. tempt you into taking risks when Centre.
driving.
● The sun is shining directly into Unintended lane departure is not
the camera lens. Always adapt speed to the road assumed by the system when the turn
conditions. lights are operated and during few
● Traffic signs are completely or
partially covered or difficult to The driver assistance systems do seconds after turn lights have been
discern. not relieve the driver from full switched off.
responsibility for vehicle If the system detects that the steering
● Traffic signs are incorrectly
operation. wheel is not held permanently, it
mounted or damaged.
interrupts the correction. A warning
● Traffic signs do not comply with
the Vienna Convention on Road
Lane keep assist message in the Driver Information
Centre accompanied by a warning
Signs and Signals. Lane keep assist supports the driver
chime alerts when immediate driver´s
to avoid unintended leaving of the
● The navigation map data is action is required.
lane. The front camera observes road
outdated.
edges, as well as the lane markings
between which the vehicle is driving.
178 Driving and operating
Notice Activation / deactivation ● adverse environmental
The system may be switched off if it conditions, e.g. heavy rain or
detects lanes which are too narrow, The system is activated / deactivated snow
too wide or too curved. in the vehicle settings _ in the Info
● vehicle modifications, e.g. tyres
Display.
Following preconditions have to be Switch off the system if the system is
fulfilled: The system is automatically
disturbed by tar marks, shadows,
reactivated at the next vehicle start.
● vehicle speed must be between road cracks, temporary or
approx. 43 mph and 112 mph Info Display 3 86. construction lane markings, or other
road imperfections.
● the driver must hold the steering Fault
wheel
In the event of a fault, L and C 9 Warning
● the turn lights are not activated
appear in the instrument panel,
● the electronic stability control is accompanied by a display message Always keep your attention on the
activated and not in operation and a warning chime. Seek the road and maintain proper vehicle
● the vehicle is not connected to a assistance of a workshop. position within the lane, otherwise
trailer or a bicycle carrier vehicle damage, injury or death
System limitations could occur.
● normal driving behaviour (system
detects dynamic driving style, i.e. The system performance may be Lane keep assist does not
pressure on the brake or affected by: continuously steer the vehicle.
accelerator pedal) ● a dirty or foggy windscreen or if The system may not keep the
● roads with good lane markings the windscreen is affected by vehicle in the lane or give an alert,
foreign objects, e.g. stickers even if a lane marking is detected.
● no spare wheel is used
● close vehicles ahead The steering of the lane keep
● the vehicle is not driven in a tight assist may not be sufficient to
corner ● banked roads
avoid a lane departure.
● winding or hilly roads
● road edges
● sudden lighting changes
Driving and operating 179
The system may not detect hands- lack of steering correction and/or
off driving due to external inappropriate management of the
influences like road condition and acceleration or braking.
surface and weather. The driver
has full responsibility to control the Advanced lane keep assist is an
vehicle and is always required to enhancement of the lane keep assist
keep the hands on the steering system. Thus, the current position of the
wheel while driving. vehicle within the lane is kept. This
Using the system while towing a position is not necessarily the centre
trailer or on slippery roads could of the lane.
cause loss of control of the vehicle In the case that the vehicle is driving
and a crash. Switch the system off. at the outer edge of the lane, the
system corrects the trajectory
Advanced lane keep assist smoothly towards the centre of the
currently driven lane when a
9 Warning determined speed has been
exceeded. Again, the driver will notice
The system assists the driver in a turning movement of the steering
managing the steering, wheel.
acceleration and braking within When the vehicle is steered by the
The activated system observes the
the limits of the laws of physics system, ( illuminates green in the
lane markings by using the camera
and the capabilities of the vehicle. Driver Information Centre.
located at the top of the windscreen.
Some road infrastructure
It steers the vehicle inside the However, the control of the vehicle
elements or vehicles present on
detected lane. The driver will notice a can be taken over at any time by the
the road may not be properly seen
turning movement of the steering driver. Therefore, the driver needs to
or may be poorly interpreted by the
wheel. apply some additional force when
camera, which may lead to an
unexpected change in direction, a turning the steering wheel.
180 Driving and operating
If the system detects that the driver is ● Normal driving behaviour is
not holding the wheel firmly enough, required (system detects
it triggers a series of gradual alerts. If dynamic driving style, i.e.
the interruption takes too long, the pressure on the brake or
system will be deactivated. accelerator pedal).
( extinguishes in the Driver ● Roads with good lane markings
Information Centre. The system has are required.
to be reactivated again by the driver.
● No spare wheel is used.
Advanced lane keep assist operates
● The vehicle is not driven in a tight
only in combination with adaptive
corner.
cruise control.
Adaptive cruise control 3 152. Activation
Press , successively until the Drive
Required preconditions Advanced lane keep assist is
Assist mode is selected.
activated via the Drive Assist.
● Adaptive cruise control must be The Drive Assist screen is displayed
activated. in the Driver Information Centre.
● The driver must hold the steering Info Display 3 86.
wheel.
Deactivation
● The turn lights are not activated
except when using with semi- Press , successively until the mode
automated lane change. to switch off assistance is selected.
● The Electronic Stability Control is
activated and not in operation.
● The vehicle is not connected to a
trailer or a bicycle carrier.
Programmable charging
By default, charging starts as soon as 1. Press ?.
8. Within one minute, press b to
the charging cable is connected to the
activate programmable charging.
charging port of the vehicle. It is also
possible to schedule charging using 9. Depending on version, lock the
the Info Display. vehicle.
Programmable charging is only The status indicator illuminates blue
possible when charging at a domestic indicating that programmable
electrical outlet / Green'Up socket or charging is active.
a wall box. 2. Touch a. Charging 3 189.
Programmable charging is also 3. Select Charging. Charging status 3 193.
available via the MyVauxhall App. 4. Touch b.
Driving and operating 193
Caution Fuel for diesel engines Diesel fuel that meets standard
EN16734 mixed with a biofuel that
The Diesel engines are compatible meets standard EN14214 (possibly
Do not use fuel or fuel additives with bio-fuels that conform to current containing up to 10% Fatty Acid
that contain metallic compounds and future European standards and Methyl Ester).
such as manganese-based and can be obtained from filling
additives. This may cause engine stations:
damage.
Caution
Use of fuel with a lower octane
rating than the lowest possible Paraffinic Diesel fuel that meets
rating could lead to uncontrolled standard EN15940 mixed with a
combustion and engine damage. Diesel fuel that meets standard biofuel that meets standard
EN590 mixed with a biofuel that EN14214 (possibly containing up to
The engine specific requirements meets standard EN14214 (possibly 7% Fatty Acid Methyl Ester).
regarding octane rating are given in containing up to 7% Fatty Acid Methyl
the engine data overview 3 243. A Ester).
country-specific label at the fuel filler
flap can supersede the requirement.
In certain countries, the use of a
particular fuel, e.g. a specific octane
rating, may be required to ensure
proper engine operation. The use of B20 or B30 fuel meeting
standard EN16709 is possible in your
Diesel engines. However, this use,
even occasional, requires strict
Driving and operating 195
application of the special servicing At temperatures below -15 °C, it is If you can smell fuel in your
conditions referred to as "Arduous recommended to park the car in a vehicle, have the cause of this
conditions". heated garage. remedied immediately by a
For more information, contact a Arctic grade diesel fuel can be used workshop.
workshop. at extremely low temperatures below
-20 °C. Using this fuel grade in warm A label with symbols at the fuel filler
Caution or hot climates is not recommended flap is indicating the allowed fuel
and may cause engine stalling, poor types. In Europe the pump nozzles of
The use of any other type of (bio) starting or damage on the fuel the filling stations are marked with
fuel (vegetable or animal oils, pure injection system. these symbols. Refuel only the
or diluted, domestic fuel etc.) is allowed fuel type.
strictly prohibited (risk of damage Refuelling
to the engine and fuel system). Caution
Notice
9 Danger
In case of misfuelling, do not
The only Diesel additives authorised switch on ignition.
Before refuelling, switch off
for use are those that meet the
ignition and any external heaters
B715000 standard. The fuel filler flap is located at right
with combustion chambers.
Low temperature operation rear side of vehicle.
Follow the operating and safety
At temperatures below 0 °C, some instructions of the filling station
diesel products with biodiesel blends when refuelling.
may clog, freeze or gel, which may
affect the fuel supply system. Starting 9 Danger
and engine operation may not work
properly. At ambient temperatures Fuel is flammable and explosive.
below 0 °C, use winter grade diesel No smoking. No naked flames or
fuel. sparks.
196 Driving and operating
The fuel filler flap can only be opened Press r. After depressurisation the The fuel filler cap can be attached to
if the vehicle is unlocked. Release the fuel filler flap is unlocked and bounces the hook on the fuel filler flap.
fuel filler flap by pushing the flap. a bit. Place the nozzle in straight position to
To open the fuel filler flap of a hybrid the filler neck and press with slight
vehicle, a depressurisation phase is Petrol and diesel refuelling force to insert.
required to avoid the emission of fuel To open, turn the cap slowly To refuel, switch on pump nozzle.
vapour. This can take up to one anticlockwise.
minute. After the automatic cut-off, the tank
can be topped up by operating the
pump nozzle a maximum of two more
times.
Caution
Wipe off any overflowing fuel
immediately.
Driving and operating 197
To close, turn the fuel filler cap General information higher fuel consumption and
clockwise until it clicks. CO2 emission levels and a lower
For the values specific to your
Close the flap and allow it to engage. maximum speed.
vehicle, refer to the EEC Certificate of
Fuel filler cap Conformity provided with your vehicle
or other national registration
Only use genuine fuel filler caps. documents.
Diesel-engined vehicles have special The determination of fuel
fuel filler caps. consumption is regulated by directive
R (EC) No. 715/2007 and No.
2017/1151 (in the latest applicable
Fuel consumption - CO2- version).
Emissions The specification of CO2 emission is
All values are combined values under also a constituent of the directive.
WLTP condition. The figures given must not be taken
Non-hybrid vehicle as a guarantee for the actual fuel
The fuel consumption is within a consumption of a particular vehicle.
range of 36 to 56 mpg. Furthermore, fuel consumption is
The CO2 emission is within a range of dependent on personal driving style
148 to 111 g/km. as well as road and traffic conditions.
All values are based on the EU base
Hybrid vehicle
model with standard equipment.
The fuel consumption is within a
range of 196 to 235 mpg. The calculation of fuel consumption
takes into account the vehicle's kerb
The CO2 emission is within a range of
weight, ascertained in accordance
28 to 22 g/km. with the regulations. Optional
equipment may result in slightly