Professional Documents
Culture Documents
3. Hazards Identification
The preparation is not classified as dangerous according to Directive 1999/45/EC and its
amendments.
No particular hazards known.
See selection 11 for more detailed information on health effects and symptoms.
After inhalation : If inhaled, remove to fresh air. If breathing is difficult, give oxygen, if not
breathing, give artificial respiration. Obtain medical attention.
FM–LAB–0003–R00
Page 1 of 5
PT. PLASTICOLORS EKA PERKASA
Office : Gedung Wisma Udaya Lt. 02 Modul 5
Jl. Danau Sunter Selatan Blok O-IV No. 35 Jakarta 14350
Telp : 021-65308797;65308598;65308799 Fax : 021-65308509
MATERIAL SAFETY
DATA SHEET
Factory : Jl. Cendana Raya Blok F8 No. 18
Delta Silicon 3 Industrial Park, Lippo Cikarang - Bekasi 17550
Telp : 021-29577560-63 Fax : 021-29453859-60
____________________________________________________________________________________
PLAST AMBER MFPET 17873
Product No. : F04F717873000
_____________________________________________________________________________________________________
After eye contact : In case of contact, immediately flush eyes with a copious amount of water
for at least 15 minutes. Get medical attention if irritation occurs.
See selection 11 for more detailed information on health effects and symptoms.
5. Fire-fighting measures
Extinguishing media : Use water spray jet, foam, dry chemical extinguisher, carbon dioxide, or
with draw from area and allow the fire to burn.
Special exposure hazards from the substance itself, its combustion products or from its vapours :
In case of fires, hazardous combustion gases formed are: Carbon monoxide (CO), Carbon dioxide
(CO2), Nitrogen oxides (NOx), Nitrous gases (NOx), Sulfur dioxide (SO2), and Hydrogen chloride (HCl).
Special protective equipment : Fire fighters should wear appropriate protective equipment and self-
contained equipment for fire-fighters breathing apparatus (SCBA) with a
full face-piece operated in positive pressure mode.
Personal Precautions : High risk of slipping if leaked/ spilled is not clean up. Use suitable
protective equipment (see, Chapter 8).
Environmental precautions : Avoid dispersal of spilled material and run off and contact with soil,
waterways, drains and sewers.
Methods for cleaning up : If emergency personnel are not present sweep up all spillages
immediately, avoiding making dust and place them in a suitable container
for disposal. No sparking tools should be used.
Protection against fire and explosion : Take precautions against accumulation of electrostatic charge.
Storage rooms and vessels : Keep the materials at a cool dry place. Protect from direct sunlight, rain
and violent temperature fluctuation. Fire is inhibited around storage area.
FM–LAB–0003–R00
Page 2 of 5
PT. PLASTICOLORS EKA PERKASA
Office : Gedung Wisma Udaya Lt. 02 Modul 5
Jl. Danau Sunter Selatan Blok O-IV No. 35 Jakarta 14350
Telp : 021-65308797;65308598;65308799 Fax : 021-65308509
MATERIAL SAFETY
DATA SHEET
Factory : Jl. Cendana Raya Blok F8 No. 18
Delta Silicon 3 Industrial Park, Lippo Cikarang - Bekasi 17550
Telp : 021-29577560-63 Fax : 021-29453859-60
____________________________________________________________________________________
PLAST AMBER MFPET 17873
Product No. : F04F717873000
_____________________________________________________________________________________________________
8. Exposure controls/ personal protection
Occupational exposure : Use process enclosures, local exhaust ventilation, and other engineering
controls to keep.
Eye protection : Safety eyewear complying with an approved standard should be used
when a risk assessment indicates this is necessary to avoid exposure to
liquid splashes, mists or dusts.
FM–LAB–0003–R00
Page 3 of 5
PT. PLASTICOLORS EKA PERKASA
Office : Gedung Wisma Udaya Lt. 02 Modul 5
Jl. Danau Sunter Selatan Blok O-IV No. 35 Jakarta 14350
Telp : 021-65308797;65308598;65308799 Fax : 021-65308509
MATERIAL SAFETY
DATA SHEET
Factory : Jl. Cendana Raya Blok F8 No. 18
Delta Silicon 3 Industrial Park, Lippo Cikarang - Bekasi 17550
Telp : 021-29577560-63 Fax : 021-29453859-60
____________________________________________________________________________________
PLAST AMBER MFPET 17873
Product No. : F04F717873000
_____________________________________________________________________________________________________
Hazardous reactions : No hazardous reactions when stored and handled according to prescribed
instructions.
Conditions to avoid : Keep away from heat, flame, and electrostatic charges.
Over-exposure signs/symptoms
Inhalation : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.
Skin : No known significant effects or critical hazards.
FM–LAB–0003–R00
Page 4 of 5
PT. PLASTICOLORS EKA PERKASA
Office : Gedung Wisma Udaya Lt. 02 Modul 5
Jl. Danau Sunter Selatan Blok O-IV No. 35 Jakarta 14350
Telp : 021-65308797;65308598;65308799 Fax : 021-65308509
MATERIAL SAFETY
DATA SHEET
Factory : Jl. Cendana Raya Blok F8 No. 18
Delta Silicon 3 Industrial Park, Lippo Cikarang - Bekasi 17550
Telp : 021-29577560-63 Fax : 021-29453859-60
____________________________________________________________________________________
PLAST AMBER MFPET 17873
Product No. : F04F717873000
_____________________________________________________________________________________________________
Product
The generation of waste should be avoid or minimized wherever possible. Avoid dispersal of spilled
material and runoff and contact with waterways, drains and sewers. Disposal of this product, solutions
and any by-products should at all times comply with the requirements of environmental protection and
waste disposal legislation and any regional local authority requirements.
Unclean packaging
Contaminated packaging material should be treated equivalent to residual chemicals. Clean packaging
material should be subjected to waste management schemes (recovery, recycling, reuse) according to
local legislation.
Not available.
Disclaimer
To the best of our knowledge, the data are intended to describe the product according to the safety requirements.
Data should not be taken to imply any guarantee of a particular or general specification, and shall be used only as
a guide. User of the product is responsible to ensure to his satisfaction that the product is suitable for the intended
purpose and method of use. We do not accept responsibility for any harm caused by the use of this information.
FM–LAB–0003–R00
Page 5 of 5