Professional Documents
Culture Documents
17’ 6”
8’ 6”
13'-10"
FOR TRAVEL
18’ 10”
8'-2"
8’ 10”
15'-11"
FOR OPERATION
2. Order Limitations: 2-5 Units per SIN: 1% Discount from Contract Price
6-10 Units per SIN: 1.5% Discount from Contract Price
11-19 Units per SIN: 2% Discount from Contract Price
20+ Units per SIN: TBD at Time of Order
11. (a) Time of Delivery: 210 to 360 days after receipt of order depending upon
model ordered. Stock units may be available for quicker
delivery.
11. (d) Urgent Requirements: Please Contact Mark Milazzo for Urgent Requirements
7
13. Ordering Address: Altec Industries, Inc.
1730 Vanderbilt Road
Birmingham, AL 35234
OR
17. Terms for Credit Cards: Credit Card Accepted Based on Approval. Use of credit
card may result in service charge.
19. Terms & Conditions of Installation: Final installation points will be determined
by Altec depending on plant loading & final
delivery location.
21. List of Service & Distribution Points: Reference Altec Product Catalog
8
23. Preventative Maintenance: Each unit furnished by Altec under this
contract will receive one full day of training
in the overall proper operation and
maintenance as specified in the maintenance
manual.
26. Notification Regarding CCR Altec Industries, Inc. is CCR Registered (#1CER8)
Registration:
9
ALTEC MODEL AT200AV
TELESCOPIC AERIAL DEVICE
NON-INSULATED
10
GSA STANDARD FEATURES AT200AV
11
ALTEC MODEL AT200A
TELESCOPIC AERIAL DEVICE
(NON-INSULATED)
12
GSA STANDARD FEATURES AT200A
13
ALTEC MODEL AT237
ARTICULATING TELESCOPIC AERIAL DEVICE
(NON-INSULATED)
14
GSA STANDARD FEATURES AT237
15
ALTEC MODEL A-T40C
TELESCOPIC AERIAL CABLE PLACER
(NON-INSULATED)
16
STANDARD FEATURES A-T40C CABLE PLACER
• Ground to Bottom of Platform – 35.1’ • Maximum Reel Lift Capacity – 6000 lb.
• Working Height – 40.1’ • Reel Driver Torque – 20,000 in-lb.
• Maximum Reach – 29’ • Max Reel Brake Torque – 9600 in-lb.
• Stowed Travel Height – 11.5’ (Approximate) • Strand Carrier System with Brake
• Platform Capacity – 500 lb. • Strand Reel Diameter – 24”
• Side Load Capacity – 600 lb. • Maximum Strand Brake Torque – 9600 in-lb.
• Boom Articulation – -187 to + 647 • Maximum Strand Holding Capacity – 2000 lb.
• Rotation – 7207 Non-continuous • Reel Brake Controls in Cab
• All Steel Boom Construction, Telescopic • Towline Winch – 3 Speed – 1000 lb. Capacity
• Platform Access from Ground • Hydraulic Deck Mounted Capstan Winch
• NON-INSULATED AERIAL DEVICE • Fairlead Attachment Arm
• 29” X 29” X 43.5” Steel Platform with Door. • Floor Mounted Roller System
• Engine Start/Stop at Platform and Lower Controls • Rear Torsion Bar for Stability
• Emergency Lowering Switch at Platform • Rubber Wheel Chocks
• 110 & 220 VAC Outlet at Platform and Ground • Fall Protection System
Controls • Two (2) Strobe Lights
• Two-way Communication System at Platform and • Back Up Alarm
Cab
• Emergency Equipment, Extinguisher, and Triangles
• Single Handle Controls at Platform
• Painted One Solid Color
• Lower Boom Lifting Eye: 2000 lb. Capacity
• Two (2) Operator and Maintenance Manuals
• 6,000 lb. Reel Lifter with Driver and Brake
• Ferrox Non-skid Coating Applied to Walking Surfaces
• Maximum Reel Diameter – 84”
• INTL 4300 4x2 Chassis, Automatic Transmission
• Maximum Reel Width – 71”
17
ALTEC MODEL A40P
TELESCOPIC AERIAL CABLE PLACER
(NON-INSULATED)
18
GSA STANDARD FEATURES A40P
• Ground to Bottom of Platform – 35.7' • 5,000 lb. Single Station Reel Lifter
• Working Height – 40.7' • 1,000 lb. Hydraulic Powered Towline Winch
• Maximum Reach – 29.4' • 65 feet of 7/16" Synthetic Rope
• Stowed Travel Height – 11.5' (Approximate) • Emergency Lowering Valve Located at Boom Tip
• Platform Capacity – 500 lbs. • Fall Protection System
• Sideload Capacity – 600 lbs. • Rubber Wheel Chocks
• Telescopic Steel Upper Boom (Non-Insulated) • Torsion Bar Stabilizers on Front and Rear Axles
• Lower Boom Articulation – 20 to 80 • Standard Altec Placer Line Body
• Lower Boom Lifting Eye Capacity – 2,000 lbs. • Master Body Locking System
• Rotation – 370 Non-continuous • Emergency Equipment, Extinguisher, and Triangles
• NON-INSULATED AERIAL DEVICE • Heavy Duty Pintle Hook
• 29" X 29" X 43.5" Fixed End Mounted Platform • Trailer Brake Controller for Hydraulic Braked Chassis
• Easy Platform Access from the Ground • 6-Way Trailer Receptacle
• Engine Start/Stop at Upper and Lower Controls • 110 VAC GFCI Receptacle at Rear
• Two-Way Communication System at Platform and • 2400 Watt Inverter w/ Auxiliary Batteries
Cab
• Ferrox Non-Skid Coating
• 110 VAC GFI Outlet at Platform
• Ford F650, Automatic Transmission
19
ALTEC MODEL AT30-GV
telescopic aerial device
(insulated)
20
STANDARD FEATURES AT30-GV
21
ALTEC MODEL AT30-G
TELESCOPIC AERIAL DEVICE
(INSULATED)
22
STANDARD FEATURES AT30-G
23
ALTEC MODEL AT37-G
ARTICULATING TELESCOPIC AERIAL DEVICE
(INSULATED)
24
GSA STANDARD FEATURES AT37-G
25
ALTEC MODEL AT40-M
articulating telescopic aerial device
with material handling (insulated)
26
STANDARD FEATURES AT40-M
27
ALTEC MODEL LS40
ARTICULATING TELESCOPIC AERIAL DEVICE
(INSULATED)
28
Standard Features – LS40
• Stowed Travel Height – 12.3' (3.75 m) nominal • FMVSS Lighting and Reflectors with Additional Rear
Tail/Stop/Turn Signals Located in Elevated Area
• Platform Capacity – 350 lbs. (158.8 kg)
• Electronic Back Up Alarm
• Two Section Telescopic Boom
• Interior Compartmentation Consisting of a
• Category C, 46KV ANSI Dielectric Rating Workbench, Storage Drawers, Shelves and Storage
• Fiberglass Second Stage Bins
• Altec Single Handle ISO-Grip® System • Three Interior Dome Lights
• 3607 Rotation • Ferrox Non-Skid Material on All Walking Surfaces.
• Automatic Hydraulic Platform Leveling with Power • Painted Standard White, Body and Aerial
Tilt Feature • Freightliner Model MT55 Forward Control Chassis
• Platform Access Directly from Cab of Truck • 24,000 GVWR, 148" Wheelbase; Heavy Duty Frame
• One (1) 24" x 24" x 42" (610 x 610 x1060 mm) Side • 200 hp Diesel Engine, Automatic Transmission;
Mounted Fiberglass Platform Hydraulic Brakes
• Electro-Hydraulic Lower Controls, Direct Wired, Fully • Air Compressor/Condenser for Air Conditioning
Proportional, Installed Adjacent to Driver
• 9,000 lb Front Axle Capacity, 15,000 lb Rear Axle
• Full Pressure Hydraulic Platform Controls with Capacity
Multifunctional Single Lever Control
• 40 gallon Fuel Tank, Tilting Steering Wheel, Engine
• Lower Controls Completely Override Platform Block Heater.
Controls
• 160 amp Alternator, Two (2) Batteries, 1300 CCA
• 12 Volt Auxiliary Power System to Permit Storing of
Unit in the Event of a Loss of Primary Power Source • 255/70R - 22.5 Tires; Adequate for GAWR Rating
• Remote Start & Stop of Truck Engine from Platform Reach Diagram LS40
• Attachment for Personnel Fall Arrest System
• Personnel Fall Arrest System for Aerial Operator
• Space Saving Truss Pedestal and Bridge
Arrangement for Fully Enclosed Van Body
Installation.
• Boom Stowage Support Located Adjacent to Cab
• Positive Boom Latching Device for Road Travel
Security
• Torsion Bar Stabilizer (no outriggers)
• 15 gallon Capacity Hydraulic Reservoir
• PTO/Hydraulic Pump Installed
• Two (2) Operator, Maintenance, and Parts Manuals
• Custom Aluminum Parcel Delivery Type Van Body,
Fully Enclosed
• Body Cargo Area is 12.5' long x 6.7' high x 7.5' wide
• Half Cab Design to Accommodate Boom Storage
• Body Fully Insulated with Interior Lining
• Double Opening Rear Doors for Easy Cargo Access/
Loading
• Bulkhead Between Driver’s Compartment and Body
Cargo Area
• Magnum 300 Driver’s Seat, Fully Adjustable with
3-Point Seat Belt
29
ALTEC MODEL L37M
OVERCENTER ARTICULATING AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
30
GSA STANDARD FEATURES L37M
31
ALTEC MODEL L42A
OVERCENTER ARTICULATING AERIAL DEVICE
(INSULATED)
32
GSA STANDARD FEATURES L42A
33
ALTEC MODEL L42M
OVERCENTER ARTICULATING AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
34
GSA STANDARD FEATURES L42M
• Ground to Bottom of Platform – 42.6' • Lower Control Station with Override of Upper
• Working Height – 47.6' Controls
• Maximum Reach – 35.2' • Platform Cover
• Stowed Travel Height – 10.8' (Approximate) • Platform Liner
• Platform Capacity – 400 lb. • Scuff Pad to Protect Liner Floor
• Lower Boom Articulation – 0 to 125 • “Category C, 46kV and Below” ANSI Dielectric
Rating
• Upper Boom Articulation – 0 to 205
• Fall Protection System
• Upper Boom Low Stow for Easy Platform Access
• Full Line Body
• Continuous Rotation
• Security Door Locks
• Platform Access from Ground
• Tailshelf
• Fiberglass Upper Boom w/ Gelcoat Finish
• 2" Ball and Pintle Hook
• Steel Lower Boom Box Structure w/ 15" Fiberglass
Insert • 7-Way Trailer Receptacle
• Mechanical Platform Leveling System • Glad Hand Connectors
• 24" X 30" X 42" Side Mount Platform w/ 90 Rotator • Hydraulic Hourmeter
• Hydraulic Platform Tilt • Rubber Wheel Chocks
• Engine Start/Stop at Platform and Lower Controls • Two (2) Strobe Lights
• Secondary Stowage System • Back Up and Outrigger Motion Alarm
• Hydraulic Tool Circuits at Platform, Two (2) Sets • Painted One Solid Color
• Material Handling Jib/ Winch Package at Boom Tip • Ferrox Non-Skid Coating Applied to Walking
Surfaces
• Jib Line Swivel Hook
• Emergency Equipment, Extinguisher, and Triangles
• Altec Single Handle ISO-Grip® Control System
• Two (2) Operator and Maintenance Manuals
• Front and Rear Outriggers
• INTL 4300V 4x2 Chassis, Automatic Transmission
• Outrigger Boom Interlock System
• Outrigger Pads and Holders
35
ALTEC MODEL LRV58
OVERCENTER ARTICULATING AERIAL DEVICE
(INSULATED)
36
GSA STANDARD FEATURES LRV58
37
ALTEC MODEL LRV57-RM
OVERCENTER ARTICULATING AERIAL DEVICE
(INSULATED)
38
GSA STANDARD FEATURES LRV57-RM
39
ALTEC MODEL LRV60-E70
OVERCENTER ARTICULATING AERIAL DEVICE
(INSULATED)
40
GSA STANDARD FEATURES LRV60-E70
41
ALTEC MODEL TA37M
ARTICULATING TELESCOPIC AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
42
GSA STANDARD FEATURES TA37M
• Ground to Bottom of Platform – 37’ • Lower Control Station with Override of Upper
Controls
• Working Height – 40.5’
• Platform Cover
• Maximum Reach – 27.5’
• Platform Liner
• Stowed Travel Height – 11.5’ (Approximate)
• “Category C, 50kV and Below” ANSI Dielectric
• Platform Capacity – 350 lb. Rating
• Compensating Articulating Arm • Fall Protection System
• Articulating Arm Articulation -57 to + 917 • Full Line Body
• Upper Boom Articulation -387 to + 757 • Security Door Locks
• Continuous Rotation • Tailshelf at Rear
• Platform Access from Ground • Pintle Hook
• Telescopic Fiberglass Upper Boom w/ Gelcoat Finish • 6-way trailer receptacle
• Steel Lower Boom w/ 12” Fiberglass Insert • Glad Hand Connectors
• Hydraulic Platform Leveling System • Hydraulic Hourmeter
• 24” X 30” X 42” Platform • Rubber Wheel Chocks
• Hydraulic Platform Tilt • Rubber Dock Bumpers
• Engine Start/Stop at Platform and Lower Controls • Splash Aprons
• Secondary Stowage System • Strobe Light
• Hydraulic Tool Circuit at Platform • Back Up and Outrigger Motion Alarm
• Material Handling Jib/ Winch at Boom Tip • Painted One Solid Color
• Jib Line Swivel Hook • Emergency Equipment, Extinguisher, and Triangles
• Altec Single Handle ISO-Grip® Control System • Two (2) Operator and Maintenance Manuals
• A-Frame Outriggers, One (1) Set • Ferrox non-skid coating applied to walking surfaces
• Outrigger Boom Interlock System • Ford F550 Chassis, Automatic Transmission
• Outrigger Pads and Holders
43
ALTEC MODEL TA45
ARTICULATING TELESCOPIC AERIAL DEVICE
(INSULATED)
44
GSA STANDARD FEATURES TA45
50 15.2
45 13.7
40 12.2
75°
35 10.7
30 9.2
REACH DIAGRAM TA45
25 0° 7.6
20 6.1
15 4.6
-38°
10 3.1
5 1.5
0 0
15 10 5 0 5 10 15 20 25 30 35
FEET
45
ALTEC MODEL TA45M
ARTICULATING TELESCOPIC AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
46
GSA STANDARD FEATURES TA45M
• Ground to Bottom of Platform – 44.5' • Lower Control Station with Override of Upper
• Working Height – 49.5' Controls
• Maximum Reach – 30.5' • Platform Cover
• Stowed Travel Height – 11.6' (Approximate) • Platform Liner
• Platform Capacity – 350 lb. • “Category C, 46kV and Below” ANSI Dielectric
Rating
• Compensating Articulating Arm
• Fall Protection System
• Articulating Arm Articulation – 5 to 91
• Full Line Body
• Upper Boom Articulation – 38 to 75
• Security Door Locks
• Continuous Rotation
• Tailshelf at Rear
• Platform Access from Ground
• Pintle Hook
• Telescopic Fiberglass Upper Boom w/ Gelcoat Finish
• 6-Way Trailer Receptacle
• Steel Lower Boom w/ 55" Fiberglass Insert
• Glad Hand Connectors
• Hydraulic Platform Leveling System
• Hydraulic Hourmeter
• 24" X 30" X 42" Side Mount Platform 90 Rotator
• Rubber Wheel Chocks
• Hydraulic Platform Tilt
• Rubber Dock Bumpers
• Engine Start/Stop at Platform and Lower Controls
• Splash Aprons
• Secondary Stowage System
• Strobe Light
• Hydraulic Tool Circuit at Platform
• Back Up and Outrigger Motion Alarm
• Material Handling Jib/ Winch at Boom Tip
• Painted One Solid Color
• Jib Line Swivel Hook
• Emergency Equipment, Extinguisher, and Triangles
• Altec Single Handle ISO-Grip® Control System
• Two (2) Operator and Maintenance Manuals
• Modified A-Frame Outriggers, One (1) Set
• Ferrox Non-Skid Coating Applied to Walking
• Outrigger Boom Interlock System Surfaces
• Outrigger Pads and Holders • INTL 4300 4x2 Chassis, Automatic Transmission
50 15.2
0 0
30 117 115 111 106 105
15 10 5 0 5 10 15 20 25 30 35
35 61 60 58 55 55
FEET
47
ALTEC MODEL TA50
ARTICULATING TELESCOPIC AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
48
GSA STANDARD FEATURES TA50
• Ground to Bottom of Platform – 49.5' • Lower Control Station with Override of Upper
• Working Height – 54.5' Controls
• Maximum Reach – 36.2' • Platform Cover
• Stowed Travel Height – 11.6' (Approximate) • Platform Liner
• Platform Capacity – 350 lb. • “Category C, 46kV and Below” ANSI Dielectric
Rating
• Compensating Articulating Arm
• Fall Protection System
• Articulating Arm Articulation – 5 to 91
• Full Line Body
• Upper Boom Articulation – 38 to 75
• Security Door Locks
• Continuous Rotation
• Tailshelf at Rear
• Platform Access from Ground
• Pintle Hook
• Telescopic Fiberglass Upper Boom w/ Gelcoat Finish
• 6-Way Trailer Receptacle
• Steel Lower Boom w/ 55" Fiberglass Insert
• Glad Hand Connectors
• Hydraulic Platform Leveling System
• Hydraulic Hourmeter
• 24" X 48" X 42" End Mount Platform w/ 180 Rotator
• Rubber Dock Bumpers
• Hydraulic Platform Tilt
• Splash Aprons
• Engine Start/Stop at Platform and Lower Controls
• Rubber Wheel Chocks
• Secondary Stowage System
• Strobe Light
• Hydraulic Tool Circuit at Platform
• Back Up and Outrigger Motion Alarm
• Material Handling Jib/ Winch at Boom Tip
• Painted One Solid Color
• Jib Line Swivel Hook
• Emergency Equipment, Extinguisher, and Triangles
• Altec Single Handle ISO-Grip® Control System
• Two (2) Operator and Maintenance Manuals
• Outriggers, Two (2) Sets
• Ferrox Non-Skid Coating Applied to Walking
• Outrigger Boom Interlock System Surfaces
• Outrigger Pads and Holders • INTL 4300 4x2 Chassis, Automatic Transmission
49
ALTEC MODEL TA60
ARTICULATING TELESCOPIC AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
50
GSA STANDARD FEATURES TA60
• Ground to Bottom of Platform – 59.8' • Lower Control Station with Override of Upper
• Working Height – 64.8' Controls
• Maximum Reach – 40.1' • Platform Cover
• Stowed Travel Height – 11.6' (Approximate) • Platform Liner
• Platform Capacity – 700 lb. • “Category C, 46kV and Below” ANSI Dielectric
Rating
• Compensating Articulating Arm
• Two (2) Fall Protection Systems
• Articulating Arm Articulation – 5 to 91
• Full Line Body
• Upper Boom Articulation – 38 to 75
• Security Door Locks
• Continuous Rotation
• Tailshelf at Rear
• Platform Access from Ground
• Pintle Hook
• Telescopic Fiberglass Upper Boom w/ Gelcoat Finish
• Glad Hand Connectors
• Steel Lower Boom w/ 55" Fiberglass Insert
• 6-Way Trailer Receptacle
• Hydraulic Platform Leveling System
• Hydraulic Hourmeter
• 24" X 48" X 42" End Mount Platform w/ 180 Rotator
• Rubber Wheel Chocks
• Hydraulic Platform Tilt
• Rubber Dock Bumpers
• Engine Start/Stop at Platform and Lower Controls
• Splash Aprons
• Secondary Stowage System
• Strobe Light
• Hydraulic Tool Circuit at Platform
• Back Up and Outrigger Motion Alarm
• Material Handling Jib/ Winch at Boom Tip
• Painted One Solid Color
• Jib Line Swivel Hook
• Emergency Equipment, Extinguisher, and Triangles
• Altec Single Handle ISO-Grip® Control System
• Two (2) Operator and Maintenance Manuals
• Outriggers, Two (2) Sets
• Ferrox Non-Skid Coating Applied to Walking
• Outrigger Boom Interlock System Surfaces
• Outrigger Pads and Holders • INTL 4300 4x2 Chassis, Automatic Transmission
51
ALTEC MODEL AN650MH
NON-OVERCENTER AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
52
STANDARD FEATURES AN650
53
ALTEC MODEL AA755
NON-OVERCENTER AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
54
GSA STANDARD FEATURES AA755
55
ALTEC MODEL AA55
NON-OVERCENTER aerial device
with material handling (insulated)
56
STANDARD FEATURES AA55
57
ALTEC MODEL AA55E
NON-OVERCENTER AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
58
STANDARD FEATURES AA55E
59
ALTEC MODEL AM55
OVERCENTER AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
60
GSA STANDARD FEATURES AM55
-45 1500
-30 1050
-15 815
0 740
15 795
30 1005
45 1350
60 1990
70 2000
61
ALTEC MODEL AM60
OVERCENTER AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
62
GSA STANDARD FEATURES AM60
-45 1210
-30 785
-15 570
0 500
15 555
30 745
45 1065
60 1685
70 2000
63
ALTEC MODEL AM900P
NON-OVERCENTER AERIAL DEVICE
(INSULATED)
64
GSA STANDARD FEATURES AM900
65
ALTEC MODEL AM900-E100
NON-OVERCENTER AERIAL DEVICE
WITH EXTENDED REACH ELEVATOR (INSULATED)
66
GSA STANDARD FEATURES AM900-E100
67
ALTEC MODEL A77-T
NON-OVERCENTER TELESCOPIC AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
68
GSA STANDARD FEATURES A77-T
-80 2000
-60 2000
-40 1862
-20 1318
0 1147
20 1318
40 1862
60 2000
70 2000
69
ALTEC MODEL A77T-E93
NON-OVERCENTER AERIAL DEVICE
WITH EXTENDED REACH ELEVATOR (INSULATED)
70
GSA STANDARD FEATURES A77T-E93
• Ground to Bottom of Platform – 92.7' • Two (2) Sets of Hydraulic Tool Circuits at Boom Tip
• Working Height – 97.7' • Two (2) Sets of Radial Outriggers
• Maximum Reach – 46.5' • Outrigger Boom Interlock System
• Stowed Travel Height – 13.0' (Approximate) • Outrigger Pads and Holders
• Platform Capacity – 350 lbs. each • Platform Cover
• Upper Boom Articulation – 0 to 165 • Platform Liner
• Lower Boom Articulation – 0 to 95 • Fall Protection Systems (2)
• Elevator Articulation – 0 to 90 • Full Line Body
• Single Elevator for Compact Unit Configuration • Security Door Locks
• Continuous Rotation • Tailshelf w/ Cable Steps at Rear
• Fiberglass Upper Boom with Gelcoat Finish • Pintle Hook
• Upper Boom Has Capability to Telescope 7' • 3-Point Grounding System
• Steel Lower Boom with 30" Fiberglass Insert • Trailer Receptacle
• “Category B, 69kV and Below” ANSI Dielectric • Glad Hand Connectors
Rating • Hydraulic Hourmeter
• Single 24" X 48" X 42" Side Mount Platform w/ 90 • Rubber Dock Bumpers
Rotator • Rubber Wheel Chocks
• Platform Access from the Ground • Splash Aprons
• Hydraulic Platform Leveling System • Two (2) Strobe Light
• Hydraulic Platform Tilt • Back Up and Outrigger Motion Alarm
• Altec Single Handle ISO-Grip® Control System • Emergency Equipment, Extinguisher, and Triangles
• Engine Start/Stop with Secondary Stowage System • Painted One Solid Color
• Lower Control Station with Override of Upper • Ferrox Non-Skid Coating Applied to Walking
Controls Surfaces
• Material Handling Jib/ Winch Package at Boom Tip • Two (2) Operator and Maintenance Manuals
• Hydraulic Extendible Jib • INTL 7400 6x4 Chassis, Automatic Transmission
• Jib Line Swivel Hook
-80 2000
-60 2000
-40 1862
-20 1318
0 1147
20 1318
40 1862
60 2000
70 2000
71
ALTEC MODEL AH100
ARTICULATING TELESCOPIC AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
72
GSA STANDARD FEATURES AH100
• Ground to Bottom of Platform Height – 95' • Scuff Pad to Protect Liner Floor
• Working Height – 100' • Two (2) Fall Protection Systems
• Horizontal Reach – 50.5' at 57' Working Height • Two (2) Front Vertical Compartments
• Stowed Travel Height – 13.5' Maximum • Cab Guard with Rear Window Guard
• Platform Capacity – 800 lbs. • Platform Access from Deck
• Upper Boom Articulation – 160 • Boom Stowage Back of Cab
• Lower Boom Articulation – 90 • PTO Hourmeter
• 360 Continuous Rotation • Rubber Wheel Chocks
• Unobstructed Bed Space (booms in stowed position • Amber Strobe Light
do not interfere with bed space)
• Back Up Alarm
• Telescopic Upper and Lower Boom Sections for
Compact Configuration when Unit is Stowed for • Painted One Color
Travel • Ferrox Non-Skid Material on All Walkways
• Atmospheric Vents for Vacuum Flashover Protection • Two (2) Operator, Maintenance, & Parts Manuals
• Upper Boom has 11' Hydraulic Extension Capability • INTL 7500 6x4 Chassis, Automatic Transmission
• Lower Boom has 14' Hydraulic Extension Capability
• Steel Lower Boom with 18" Fiberglass Insulator Additional Options Available from OPTIONS LIST
• Sealed Fiberglass Upper Boom with Gelcoat Exterior
Finish
• “Category A, 500 kV and Below” ANSI Dielectric
Rating
• One (1) 40" X 60" X 42" End Mounted Platform Reach Diagram AH100
• Platform Access from the Ground
100'
• Hydraulic Platform Leveling System
• 180 Platform Rotation 90'
• Hydraulic Platform Tilt
80'
• Single-Handle Control (Four Functions)
• Outrigger Boom Interlock System 70'
• Lower Control Station with Nighttime Illumination
and Upper Control Override 60'
• 2,100 lb. Combined Platform and Material Handling
Capacity in All Boom Positions 50'
• 1,500 lb. All Position Material Handling Jib/ Winch
Package at Boom Tip 40'
• Jib/Winch Assembly Rotates and Levels with the
Platform 30'
• 17" Hydraulically Extendible Jib
20'
• Two (2) Sets of Hydraulic Tool Circuits at Boom Tip
• Two (2) Sets of Radial Outriggers 10'
• Bubble Level Indicators at Outrigger Control
Locations AH 100
• Platform Cover
0' 10' 20' 30' 40' 50'
• Platform Liner
73
ALTEC MODEL HL125
ARTICULATING TELESCOPIC AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
74
GSA STANDARD FEATURES HL125
• Ground to Bottom of Platform Height – 120' • Two (2) Front Vertical Compartments
• Working Height – 125' • Cab Guard with Rear Window Guard
• Maximum Reach – 45.1' • Platform Access from Deck
• Stowed Travel Height – 13.5' maximum • Boom Stowage back of Cab
• Platform Capacity – 800 lbs. • PTO Hourmeter
• Upper Boom Articulation – 140 • Rubber Wheel Chocks
• Lower Boom Articulation – 85 • Amber Strobe Light
• 360 Continuous Rotation • Back Up Alarm
• Unobstructed Bed Space (booms in stowed position • Painted One Color
do not interfere with bed space)
• Ferrox Non-Skid Material on All Walkways
• Sealed Fiberglass Upper Boom with Gelcoat Exterior
Finish • Two (2) Operator, Maintenance, & Parts Manuals
• The Steel Lower Boom has Three Sections, Two of • INTL 7500 6x4 Chassis, Automatic Transmission
Which Telescope to Provide 20' (6.1 m) of Extension
Each
Additional Options Available from OPTIONS LIST
• “Category A, 500 kV and Below” ANSI Dielectric
Rating
• One (1) 40" X 60" X 42" End Mounted Platform
• Hydraulic Platform Leveling System
• 180 Platform Rotation Reach Diagram HL125
• Hydraulic Platform Tilt
• Single Handle Upper Control (four functions) with 120’
Nighttime Illumination
110’
• Lower Control Station with Nighttime Illumination
and Override of Upper Controls
100’
• Atmospheric Vents for Vacuum Flashover Protection
• 2,100 lb. Combined Platform and Material Handling 90’
Capacity in All Boom Positions
80’
• 1,500 lb. All Position Material Handling Jib/Winch
Package at Boom Tip
70’
• Jib/Winch Assembly Rotates and Levels with the
Platform
60’
• 17" Hydraulically Extendible Jib
• Two (2) Sets of Hydraulic Tool Circuits at Boom Tip 50’
75
ALTEC MODEL AH125
ARTICULATING TELESCOPIC AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
76
STANDARD FEATURES AH125
• Ground to Bottom of Platform – 118' • Anti-Skid Scuff Pad to Protect Liner Floor with
Integral Step
• Working Height – 123'
• Access from Deck to Personnel Platform
• Horizontal Reach – 50.4' 6" at 75' Working Height
• Access Steps from Ground to Platform Deck
• Personal Fall Protection Systems (2)
• PTO Hourmeter
• Boom Stowage Back of Cab
• Rubber Wheel Chocks; set of 4
• Platform Capacity – 800 lbs. (see platform options)
• Strobe Light, Amber
• Upper Boom Articulation – 160
• Back Up Alarm
• Lower Boom Elevation – 87
• Painted One Solid Color
• Unobstructed Bed Space (booms in stowed position
do not interfere with bed space) • Non-Skid Material on All Walkways
• Telescopic Upper and Lower Boom Sections for • Two (2) Operator, Maintenance, & Parts Manuals
Compact Configuration when Unit is Stowed for
Travel. • Low Cab Forward (6x4 or 6x6) Peterbilt 320 or
Autocar
• 360 Continuous Rotation
• Stowe Width: Maximum 102"
• Upper Boom has 7' Hydraulic Extension Capability
• Stowed Length Maximum of 40'
• Lower Boom has 40' Hydraulic Extension Capability
• Stowed Travel Height – 13' 6" Maximum
• Steel Three (3) Section Lower Boom
• Peterbilt 6x4 320, Manual Transmission
• Sealed Fiberglass Two (2) Section Upper Boom
• Category A, 500 kV and Below - ANSI Dielectric Additional Options Available from OPTIONS LIST
Rating
• One (1) Standard 40" X 60" X 42" End Mounted Reach Diagram AH125
Platform, with Entrance/Egress Steps; 800 lb.
Capacity (see platform options)
120’
• Platform Access from the Ground
• Hydraulic Platform Leveling System 110’
• 180 Platform Rotation
100’
• Hydraulic Platform Tilt
• Single Handle Upper Controls (four functions) 90’
• Lower Control Station with Nighttime Illumination
and Upper Control Override 80’
77
ALTEC MODEL AH150
ARTICULATING TELESCOPIC AERIAL DEVICE
WITH MATERIAL HANDLING (INSULATED)
78
STANDARD FEATURES AH150
• Ground to Bottom of Platform – 145' • Anti-Skid Scuff Pad to Protect Liner Floor with
Integral Step
• Working Height – 150'
• Fall Protection Systems (2)
• Horizontal Reach – 60' 3" at 70.2' Working Height
• Access to Personnel Platform from Deck
• Road Travel Security for Upper & Lower Boom
• Rubber Wheel Chocks (4)
• Platform Capacity – 800 lbs. (see platform options)
• Strobe Light, Amber
• Upper Boom Articulation – 160
• PTO Hourmeter
• Lower Boom Elevation – 87
• Back Up Alarm
• 360 Continuous Rotation
• Painted One Solid Color
• Unobstructed Bed Space (booms in stowed position
do not interfere with bed space) • Non-Skid Material on All Walkways
• Telescopic Upper and Lower Boom Sections for • Two (2) Operator, Maintenance, & Parts Manuals
Compact Configuration when Unit is Stowed for
Travel. • Low Cab Forward (10x6) Peterbilt 320, Tandem Steer
Front / Ridem Rear
• Steel Lower Boom
• Stowed Length Maximum of 40'
• Lower Boom has 49' Hydraulic Extension Capability
• Stowed Width, Maximum of 102"
• Upper Boom has 12' Hydraulic Extension Capability
• Peterbilt 320 Tandem Steer, Manual Transmission
• Fiberglass Upper Boom
• Category A, 765 kV and Below” ANSI Dielectric
Additional Options Available from OPTIONS LIST
Rating
• One (1) Standard 40" X 60" X 42" End Mounted
Platform
Reach Diagram AH150
• Platform Access from the Ground
• Hydraulic Platform Leveling System
• 180 Platform Rotation
• Hydraulic Platform Tilt
• Individual Controls (see options for single stick
controller)
• Lower Control Station with Nighttime Illumination
and Upper Control Override
• Atmospheric Vents for Vacuum Flashover Protection
• Stowed Travel Height – 13' 6" Maximum
• 1,600 lb. Combined Platform and Material Handling
Capacity in All Boom Positions
• 1,000 lb. All Position Material Handling Jib/ Winch
Package at Boom Tip
• Jib/Winch Assembly Rotates and Levels with the
Platform.
• 14" Hydraulic Extendible Jib
• Two (2) Sets of Hydraulic Tool Circuits at Boom Tip
• Two (2) Sets Heavy-Duty Post & Beam Outriggers
• Inclinometers at Outrigger Control Locations
• Platform Cover
• Polyethylene Platform Liner
79
ALTEC MODEL DB35
DIGGER DERRICK
80
GSA STANDARD FEATURES DB35
• Maximum Sheave Height – 42.9’ (with jib) • Platform, Fiberglass Pin-On, 24” X 24” X 42”
• Maximum Horizontal Reach – 30.2’ • Platform Cover
• Maximum Digging Radius – 19.5’ • Radio Remote Control
• Elevation – 6 to 75 • Docking Station for Use with Radio Remote Contol
at Boom Tip
• Outrigger Motion Alarm
• Pole Guide
• Digger, Single Speed, fully proportional,
2,500 ft-lbs. • Pole Carrier, 2,000 lbs. Max Weight
• Auger Assembly, 18” • Cargo Platform, Fold Out – 1,300 lbs. Max Weight
• Rope, Material Handling, .5” X 80’ • Tool Circuit Below Rotation
• Outrigger/Boom Interlock System • Outrigger Pads
• Swivel Hook/Downhaul Weight • Fall Protection System
• Trailer – 10,000 lbs. GVWR • 5 lbs. Fire Extinguisher
• Jib, 8’ Material Handling • Hinowa Tracked Carrier, 23.5 hp Diesel Engine
81
ALTEC MODEL DL45
DIGGER DERRICK
82
GSA STANDARD FEATURES DL45
83
ALTEC MODEL DM47
DIGGER DERRICK
84
GSA STANDARD FEATURES DM47
85
ALTEC MODEL D2050A
DIGGER DERRICK
86
GSA STANDARD FEATURES D2050A
- 21.13LR 0.0 4,643 31.13LR 0.0 2,365 30.46LR 0.0 2,942 40.46LR 0.0 1,632
A Capacities in the shaded blocks reflect capacities utilizing a two-part load line. These capacities are based on a 15,000 pound bare
drum capacity winch.
B Load being lifted must not exceed winch line rated working load multiplied by the number of parts of winch line.
C Capacities are shown with the transferable flares (if so equipped) attached to the intermediate boom. With the transferable flares
pinned to the upper boom, capacities with the upper boom extended or both extended will be reduced by approximately 100 pounds.
87
ALTEC MODEL D3055A
DIGGER DERRICK
88
GSA STANDARD FEATURES D3055A
89
ALTEC MODEL D4060A
DIGGER DERRICK
90
GSA STANDARD FEATURES D4060A
91
ALTEC MODEL DT80
DIGGER DERRICK
92
GSA STANDARD FEATURES DT80
• 79.8' of Pole Setting Sheave Height • RotaFloat Screw Anchor Installation Security
• 36' Digging Radius • Boom Stow Protection
• 69.7' of Horizontal Reach from Centerline of Rotation • 8.5-Ton Swivel Hook/Downhaul Wt. Combination
• 23,500 lbs. Capacity at 10' with Digging System Installed • 250' of 5/8" WCRA Flex 35 Rotation Resistant Wire Rope
• Stowed Travel Height – 13.4 ‘ (Approximately) • Nylon Sling and Wire Rope Sling
• 24" Dirt Auger • Saddle Box Tool Storage Compartments with Flatbed Body
• 15 to 80 Boom Elevation • Security Door Locks
• 15,000 lb. Turntable Winch • Hydraulic Tamp Storage Provision
• Hydraulically Extended 3rd & 4th Stage Steel Booms • Spring Loaded Hose Reel w/ 50' Hoses at Rear
• 3rd & 4th Stage Booms Extend Simultaneously • FMVSS Lights & Reflectors, LED
• Non-Insulated Booms • Auger Storage Bracket
• Steel Transferable Boom Flares • Rubber Dock Bumpers
• Two-Speed 16,500 ft./lbs. Hydra-Sync Digger • Pintle Hook
• Digger Transfer Protection • Glad Hand Connectors
• Auger Stow Protection • 3-Point Grounding System
• Pole Guides w/ Pole Guide Interlock • Two (2) Strobe Lights
• Radial Front and Rear Outriggers • Seven-Way Trailer Light Socket at Rear
• Outrigger Boom Interlock System • Hydraulic Hour Meter
• Outrigger Pads and Holders • Back Up and Outrigger Motion Alarm
• Riding Seat Lower Controls w/ Foot Throttle • Rubber Wheel Chocks
• Engine Start/Stop • Paint One Solid Color
• Standard 80-Gallon Hydraulic Reservoir • Ferrox Non-Skid Coating Applied to Walking Surfaces
• Continuous Rotation • Two Operator and Maintenance Manuals
• Hydraulic Overload Protection • Emergency Equipment, Extinguisher, and Triangles
• Electronic Side Load Protection • INTL 7400 6x4 Chassis, Automatic Transmission
93
ALTEC MODEL HD35A
HYDRAULIC PRESSURE DIGGER
94
GSA STANDARD FEATURES HD35A
• Hydraulic Pressure Digger with 22' Digging Depth • 36" Dirt Auger Included
• 22' Telescopic Pole Setter • 4' Steel Cable Sling
• John Deere CK6068TP3 155HP Diesel Engine • Seven-Way Trailer Light Socket at Rear
• Hydraulic System with 6,000 PSI Hydrostatic Pump • Pintle Hook with Safety Rings
• Diagnostic Pressure Test Quick Disconnect Couplings • Glad Hand Connectors
• 90-Gallon Hydraulic Reservoir • Lights and Reflectors per FMVSS #108
• Operator’s Control Station with Arm Rest Controls • Two (2) Strobe Lights
• Pressure Digger Mast Including 3.5" Kelly Bar • 68" Diameter Plastic Umbrella
• Altec Inertia Drive System • Rear Window Guard
• Mast Leveling Control • 18" x 18" x 48" Material Storage Box
• Two (2) Sets A-Frame Outriggers • 100-Gallon Water Tank
• Outrigger Boom Interlock System • 50-Gallon Fuel Tank for Engine
• Outrigger Pads and Holders • Two (2) Operator and Maintenance Manuals
• Outrigger Motion Alarm • Painted One Solid Color
• 240 Revolving Frame • Ferrox Non-Skid Coating Applied to Walking
Surfaces
• Lower Hydraulic Tool Circuit
• Emergency Equipment, Extinguisher, and Triangles
• Rubber Wheel Chocks
• INTL 7400 6x4 Chassis, Automatic Transmission
• Swivel Hook Installed on Winch Line Cable
• 20" Dirt Auger Included
95
ALTEC MODEL AC18-70B-HL
HYDRAULIC TELESCOPIC CRANE
96
STANDARD FEATURES AC18-70B
• 36,000 lb. (16,330 kg) Maximum Lifting Capacity • Lower Winch Control Valve
• 80’ (24.9 m) Maximum Sheave Height • Hour meter
• Hydraulic Pilot-operated Control System • Primary Pivotal A Frame, Auxiliary Modified A’s
(rear)
• Front Bumper Outrigger
• 3707 Non-continuous Rotation
• Back-Up and Outrigger Motion Alarms
• 40’ Jib, 2-Stage Telescopic
• Two (2) Operator and maintenance Manuals
• Pintle Hook T-125
• 19.5’ Flatbed
• Painted One Solid Color (black)
• LMAP Overload System
• Set of Wheel Chocks
• 5 Outrigger pads and holders
• Outrigger Boom Interlock
• Anti-Two Block device
• Start/Stop at Operator Stations
• 240x 9/16” IWRC Wire Rope
• 7,000 lbs. Downhaul Ball and Hook
• 70’ (21.3 m) 3-Section Non-Insulated Boom
• Emergency Equipment (minus Lanyard),
• Stowed Travel Height of 12.9 (3.9 m) Extinguisher, and Triangles
• 70 Gallon Hydraulic Reservoir • Ferrox Non-Skid Coating Applied to Flatbed
• 10,200 lbs. Winch • INTL 7400 6x4 Chassis Automatic Transmission
97
ALTEC MODEL AC26-103B
HYDRAULIC TELESCOPIC CRANE
98
STANDARD FEATURES AC26-103B
• 52,000 lb. (23,588 kg) Maximum Lifting Capacity • 90 Gallon Hydraulic Reservoir
• 113 ft. (34.4 m) Maximum Sheave Height • 12,000 lbs. Winch
• Hydraulic Pilot-Operated Control System • 3707 Non-Continuous Rotation
• Standard Front Bumper Outrigger • 44’ 2 Stage telescopic Jib
• 3607 Working Capacity • Pintle Hook
• Back-Up and Outrigger Motion Alarms • Painted One Solid Color (Black)
• Two (2) Operator and Maintenance Manuals • Set of Wheel Chocks
• 24’ Long Flatbed • Splash Aprons
• LMAP Overload System • Outrigger Boom Interlock
• 5 Outrigger Pads and Holders • Hydraulic Hourmeter
• Anti-Two Block Device • Start/Stop at Operator Stations
• Drum Rotation Indicator • 7-Ton Capacity Downhaul Ball
• 350’ x 9/16” IWRC Wire Rope • Extinguisher and Triangles
• 103’ (31.4 m) 4 Section Non-Insulated Boom • Ferrox Non-Skid Coating Applied to Walking
Surfaces
• Stowed Travel Height of 13.3 ft
• INTL 7500 6x4 Chassis, Automatic Transmission
99
ALTEC MODEL AC38-127S
HYDRAULIC TELESCOPIC CRANE
100
STANDARD FEATURES AC38-127S
101
ALTEC MODEL HW80
HOT LINE INSULATOR WASHER
102
GSA STANDARD FEATURES HW80
• 375 Platform Rotation • The Rear Fenders are Fabricated from 3/16 inch (4.8
mm) Thick Aluminum. They are designed with built
• Front and Rear Outriggers in stairs and handrails for access to the cross-over
• Outrigger Boom Interlock platform located on top of the subbase. Each fender
is bolted to the subbase for ease of replacement.
• Outrigger Pads and Holders All walkway surfaces are coated with a non-skid
coating.
• Top Hatch 18" Diameter for Filling Tank
• Grounding System – includes storage reel, 100 feet
• 80 Gallon Hydraulic Reservoir (30.5 m) of No. 2 clear jacket copper grounding
• Trailer Receptacle cable, clamp on each end, and two (2) 72 inch (1829
mm) grounding rods. Reel is manual pay-out and
• Two (2) Boom Spotlights electric rewind. For storage of cable only.
85 25.9
80 24.4
75 22.9
70 21.3
65 19.8
60 18.3
55 16.8
50 15.2
45 13.7
40 HW80 12.2
35
REACH DIAGRAM 10.7
30 9.1
25 7.6
20 6.1
15 4.6
10 3.1
5 1.5
0 0
5 1.5
10 3.1
FEET
10 5 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80
103
ALTEC MODEL RL-9
CABLE REEL HANDLING AND PULLING
SPECIAL PURPOSE VEHICLE
104
GSA STANDARD FEATURES RL9
• Maximum 8000 lb. Reel Lifter w/ Service Body • Hydraulic Tool Circuit at Rear
• Reel Lifter Capable of Handling Reels 50" – 108" Dia. • Set of 50' X 3/8" Hydraulic Tool Hoses
• Reel Lifter Capable of Handling Reels 32" – 60" Wide • Pintle Hook w/ Safety Chain Eyes at Rear
• Outer Hand for 108" Dia. Reels Weighing 6000 lbs. • Glad Hands with Air Hoses for Trailer Connection
• Inner Hand for 96" Dia. Reels Weighing 8000 lbs. • Trailer Lighting Cable
• Reel Lifter Arms Operate Independently of Each • Window Guard
Other
• Sign Storage Box
• Full Control Panel in Right Rear Compartment
• Ladder Rack
• Reel Carrying Tracks on Top of Body
• Spare Tire Carrier
• Three Spindle Reel Bars – 3", 2 ½" , 1 ½"
• Manual Jacks at Rear
• Storage Provisions for Two Reel Bars, 3rd Stored on
Hands • 20 lb. Fire Extinguisher w/Bracket
• 3000 Watt Hydraulic Generator w/ Two Electrical • Lights and Reflectors per FMVSS #108
Outlets • Strobe Light
• Hydraulic Ventilating Fan • Hydraulic Hourmeter
• 20' X 8" Dia. Duct Hose for Ventilating Fan • Tachometer at Control Station
• Heater Which Can Be Used In Conjunction w/ Fan • Two (2) Trailer Plug Light Sockets
• Ventilated Storage Compartment for Fan, Hose, & • Back Up Alarm
Heater
• Magnetic Base Deck Light w/ 25' Coiled Cord
• Cylinder Tank Storage in Body
• Magnetic Base Flood Light w/ 25' Coiled Cord
• 20,000 lb. Front Winch
• Emergency Engine Shut Down Switch at Control
• 25,000 lb. Mid-Ship Winch w/ Swivel Sheave at Rear Station
• Mid-Ship Winch Cable to Run Under Cargo Floor • Rubber Wheel Chocks
• Sump Pump w/ 50" X 2 ½" Dia. Water Hose • Paint One Solid Color
• Sump Pump Compartment in Body • Two Operator and Maintenance
• Water Hose Box • INTL 4300 4x2 Chassis, Automatic Transmission
105
ALTEC MODEL RL15D
CABLE REEL HANDLING AND PULLING
SPECIAL PURPOSE VEHICLE
106
GSA STANDARD FEATURES RL15D
• Dual 15,000 lb. Reel Loader with 6,000 lb. Rim Drive • Brake Controller Installed in Cab
• Reel Lifter Capable of Handling Reels 24" – 96" Dia. • Emergency Engine Shut Down Switch at Control
Station
• Reel Lifter Capable of Handling Reels 24" – 72" Wide
• Emergency Stop at Rear and Side Capstan
• Rim Drive Equipped with Two-Speed Hydraulic Drive
• Warner 7-Prong Trailer Light Socket
• Two Galvanized Reel Spindle Bars with Locking
Collars (Includes Air Operated Front and Rear • 2 Strobe Lights Mounted at Front Corners
Latches)
• Electric Type Throttle Control on Curbside Deck at
• Reel Lifter Arms Transfer Reels from One Set to Console
Another.
• 12 Volt Weatherproof Outlet
• Full Control Panel at Right Rear
• 3,600 Watt Inverter on Bottom of Saddle
• 25,000 3-Speed Mid-Ship Winch w/ Swivel Sheave at Compartment
Rear
• 2 120 VAC Weather
• 2,500' x 7/16" Cable for Mid-Ship Winch
• Electrical Circuits with Auto-Reset Circuit Breakers
• Mid-Ship Winch Cable to Run Under Cargo Floor
• Saddle Compartments with Adjustable Shelf Panels
• Universal Swivel Sheave Installed at Rear of Body
• Front and Rear Underslung Boxes
• Winch Controls at Rear Control Station
• Top Mounted Boxes on Top of Flatbed
• Remote Pendant Control Includes Winch Dog,
3-Speed Selector, Throttle, Take Up and Payout • Rear-Facing Compartments Mounted Over Winch
Controls and Saddle Compartment with Two Fold Down
Doors
• Two Hydraulic Outriggers at Rear
• Punched Metal Basket
• 70 Gallon Reservoir
• Cone Holders on Front Bumper
• T125 Pintle Hook
• Rubber Wheel Chocks
• Hydraulic Hose Reel with 50' of Hydraulic Hose
• Wheel Chock Holders
• Hydraulic Fluid Filled Pressure Gauges at Control
Station • Manhole Guard Holder Under Left Side of Body
• 12V Auxiliary Controls for Winch and Reel Loader • Rubber Mud Flaps
107
ALTEC MODEL LP108
TRUCK-MOUNTED UNDERGROUND AND OVERHEAD
CABLE HANDLER
108
GSA STANDARD FEATURES LP108
• Capable of Lifting Reels with 60”- 108” diameter • 7” Aluminum Capstan Head
• Capable of Lifting Reels 30”- 68” wide • Collapsible Reel with Storage
• Reel Drive Mechanism Located in Each Reel • Body, T80 Transverse Compartment
Loading Arm
• Outrigger Down Alarm
• Curbside Main Control Atation
• Load/ Unload Alarm
• Two (2) Hydraulic Rear Outriggers
• Rubber Wheel Chocks
• Two Speed Throttle Control
• Outrigger Pads and Holders
• Radio Remote Control or Tethered
• Small Reel Adapter
• Cable Level Wind System
• Wood Reel Offset Adapter
• Winch, Traction, Constant Pull, 25,000 lb. Capacity
with 9/16” x 1,310' of Wire Rope Run Under Deck. • Grounding Lug
Includes a Hydraulic Extendable Fare Lead at Rear
• Splash aprons
• Winch Line Footage Counter
• Strobes, Amber, Installed on Arms and Front
• Wire Line Tension Indicating System Brackets
• 5 gal Hydraulic Oil Reservoir with High Capacity • Deck/Winch Work Lights
Cooling
• Cone Holder
• Tool Circuit with Quick Disconnect
• Two (2) Operator’s, Parts Maintenance Manuals
• 3/8” Hose Reel, 30’
• INTL 7400 6x4, Auto Transmission
• T-125 Type Pintle Hook
109
ALTEC MODEL AD108
ARM-DRIVEN SELF-PROPELLED
CABLE HANDLER
110
GSA STANDARD FEATURES AD108
• Capable of Lifting Reels with 48”- 108” diameter • Two (2) Operator’s, Parts Maintenance Manuals
• Capable of Lifting Reels 30”- 68” wide • Deutz, Air Cooled, 4 Cylinder Diesel Engine
• Hydraulically Actuated Reel Loading Arms • 3/8” Hose Reel, 30’
• Reel Drive Mechanism Located in Each Reel • Hydraulic Jumper Circuit
Loading Arm
• Material Storage Box, Aluminum
• Two (2) Pivoting-Shoe Rear Stabilizers
• Load/ Unload Alarm
• Curbside Main Control Station
• Outrigger Down Alarm
• Radio Remote Control or Tethered
• Pilot Line Winder with Pilot Line, ½” X 1,000’
• Two Speed Throttle Control
• Small Reel Adapter
• 20-gallon Fuel Tank
• Tool Circuit with Quick Disconnect
• Hydraulically Retractable Nose Wheel
• Wood Reel Offset Adapter
• Air Operated Brakes ABS
• Rubber Wheel Chocks
• Grounding Lug
• Strobe, Amber Installed on Each Arm
• Splash Aprons
111
ALTEC MODEL ET5
CARGO POLE TRAILER
112
GSA STANDARD FEATURES ET-5
• Altec Easy-Extend Tongue Requires Less Than 50 lbs. • Standard 1-Year Altec Warranty
Of Force
• Adaptable Pole Carrying Assembly Includes Two (2)
• Open Cargo Area with Drainage Holes Full Width Rail Bolsters with Adjustable Pole Cradles,
Welded Center Pole Saddle on Easy-Extend Tongue,
• Sealed Transverse Compartment at Front with a and Three (3) Intregal Pole Binding Wire Rope
Lockable Door On Both Side Winches. Bolsters over Cargo Area May Be Either
Removed or Stored at the Front of the Trailer
• Heavy-Duty Swivel – Away Jack
• Six (6) Load Tie-Down Anchors Each Rated for 5,000
• Cargo Bed and Fenders are Integral Part of Trailer
lbs.
Structure
• Tailgate: Rugged, Hinged Type, Drops 180 Degrees
• Tow Assembly Includes Adjustable Height
Connection and Dual Safety Chains Rated for Full • Altec Heavy Duty Tandem Axle with Three Point
Trailer Capacity Suspensions Is Flexible for Uneven Road Conditions
• 4-Wheel Electric Brakes • Anti-Skid Coating on Walking Surfaces
• Four (4) Heavy-Duty Wheels and Tires • Lights and Reflectors Conform to FMVSS#108
• Extendible Jumper Cable Assembly • Emergency Brake-A-Way Kit Charged by Truck
• Finished Painted Altec White and Undercoated • Two (2) Operators and Maintenance / Parts Manuals
113
ALTEC MODEL HLIW1600-T
HOT LINE INSULATOR
WASHER TRAILER
114
GSA STANDARD FEATURES HLIW1600-T
115
ALTEC MODEL DC 1217
DISC STYLE CHIPPER
6’ 8”
17’ 6”
8’ 6”
15’ 10”
116
GSA STANDARD FEATURES DC 1217
• 12" Capacity Disc Style Chipper • 2,000 lb. Capacity Front Jack
• Exclusive Patented Panic Bar to Assist in Operator • 360 Rotating Discharge Chute
Safety
• (2) Independent 4' Long x 3/8" Thick, 5,400 lb. Safety
• 85 Horsepower Kubota Turbo Diesel Chains
• 12" High x 17" Wide Dual Powered Feed Rollers • Hydraulic Filtration System
• 15'10" Long x 6'8" Wide x 8'6" High – 5640 lbs. • Hydraulic Feed System
• 42" Wide x 31 ½ High x 34" Deep Infeed Chute • 12-Gallon Hydraulic Tank
• 46" Wide X 29" Deep Folding Feed Table • 20-Gallon Fuel Tank
• Fixed Steel Pintle Ring Tow Bar • Lighting to Conform to All D.O.T. Specifications
• 12-Volt Self Adjusting Trailer Brakes • Controls Located on Curb Side
• 12-Volt Breakaway Switch • Chipper Hood Safety Switch
• (2) 245-75-R16 Radial Tires Mounted on 8 Lug • Designed for High Performance Fleet Use
Wheels
• Rugged Construction for Long Lifecycle
• Chipper Blower System
117
ALTEC MODEL DC 1419
DISC STYLE CHIPPER
7’ 6”
18’ 10”
8’ 10”
16’ 11”
118
STANDARD FEATURES DC 1419
• 14” Capacity Disc Style Chipper • 2,000 lb. Capacity Front jack
• Exclusive Patented Panic Bar to Assist in Operator • 2707 Rotating Discharge Chute
Safety
• (2) Independent 4’ Long x 3/8” Thick, 6,600 lb. Safety
• Cat 130 Horsepower Chains
• 14” High x 19” Wide Dual Powered Feed Rollers • Hydraulic Filtration System
• 18’10” Long x 7’6” Wide x 8’10” High – 6,560 lbs. • Hydraulic Feed System
• 65” Wide x 35 ½ High x 2275 Sq. Inches Deep Infeed • 15-Gallon Hydraulic Tank
Chute
• 26-Gallon Fuel Tank
• 69” Wide x 32” Deep Folding Feed Table
• Lighting to Conform to All D.O.T. Specifications
• Fixed Steel Pintle Ring Tow Bar
• Controls Located on Curb Side
• 12-Volt Self Adjusting Trailer Brakes
• Chipper Hood Safety Switch
• 12-Volt Breakaway Switch
• Designed for High Performance Fleet Use
• (2) 245-75-R16 Radical Tires Mounted on 8 Lug
Wheels • Rugged Construction for Long Lifecycle
119
ALTEC MODEL CFD 1217
control feed drum chipper
13'-10"
FOR TRAVEL
8'-2"
15'-11"
FOR OPERATION
11 GALLON
HYDRAULIC
RESERVOIR
15 GALLON
FUEL
RESERVOIR
6'-8"
120
STANDARD FEATURES CFD 1217
• 12” Capacity Drum Style Chipper • 2,000 lb. Capacity Front jack
• Exclusive Patented Panic Bar to Assist in Operator • 3607 Rotating Discharge Chute
Safety
• (2) Independent 4’ Long x 3/8” Thick, 4,400 lb. Safety
• Kubota 88 Horsepower Chains
• 12” High x 17” Wide Feed Opening, Two Feed Rollers • Hydraulic Filtration System
• 13’10” Long x 6’7” Wide x 8’2” High – 4,950 lbs. • Hydraulic Feed System
• 50” Wide x 30 High x 1500 Sq. Inches Deep Infeed • 11-Gallon Hydraulic Tank
Chute
• 20-Gallon Fuel Tank
• 53” Wide x 29” Deep Folding Feed Table
• Lighting to Conform to All D.O.T. Specifications
• Fixed Steel Pintle Ring Tow Bar
• Controls Located on Curb Side
• 12-Volt Self Adjusting Trailer Brakes
• Chipper Hood Safety Switch
• 12-Volt Breakaway Switch
• Designed for High Performance Fleet Use
• (2) 245-75-R16 Radial Tires Mounted on 8 Lug
Wheels
121
ALTEC MODEL LGS-98-56-SW
standard service body
with single rear wheel chassis
122
STANDARD FEATURES LGS-98-56-SW
• Fabricated from A40 grade 100% Zinc Alloy Coated • Metal Formed Fenders
Steel
• Automotive Underseal Applied to Entire
• 16 Gauge Outside Panels Understructure
• 16 Gauge Top Panels • Electro Cathodic Emersion Priming
• 14 Gauge End Panels • Automotive Type Non-Porous Door Seals
Mechanically Fastened to the Door Facing
• 18 Gauge Inner Door Panels
• Compartmentation–Curbside:
• 18 Gauge Outer Door Panels
• First Vertical – Two (2) Adjustable Shelves with
• 18 Gauge Shelving, Spangled Steel Dividers on 4” Centers. Vented Compartment
• 14 Gauge Wheel Panels • Horizontal – One (1) Adjustable Shelf
• 12 Gauge Steel Floor, Formed Checker Plate • Rear Vertical – Six (6) Adjustable Locking Swivel
hooks (1-4-1)
• Structural Channel Crossmembers
• Compartmentation – Streetside:
• Master Body Security Locking System
• First Vertical – Two (2) Adjustable Shelves with 4”
• Gas Cylinders for All Vertical Doors
Dividers
• Chains on Horizontal Doors
• Horizontal – Two (2) Fixed Shelves, One Midway
• 98" Overall Body Length and One in the Bottom of Compartment
• 78" Outside Width • Rear Vertical – Two (2) Adjustable Shelves with 4”
Dividers
• 40" Body Height
• Slam Action Tailgate
• 15" Compartment Depth
• Treadplate Step Bumper
• 34" Floor Width
• Lights and Reflectors in Accordance with FMVSS
• All Doors are Full, Double Paneled, Self-Sealed with #108 LED Lighting Package, Installed
Built-In Drainage.
• Back-Up Alarm
• Stainless Steel Hinge Rods
• Painted One Solid Color
• Stainless Steel Rotary Latches
• Ford F-350, Single Rear Wheel, Automatic
• Door Header Drip Rail at Top for Maximum Weather Transmission
Protection
123
ALTEC MODEL LGS-108-60-SW
standard service body
with single rear wheel chassis
124
STANDARD FEATURES LGS-108-60-SW
• Fabricated from A40 Grade 100% Zinc Alloy coated • Metal Formed Fenders
Steel
• Automotive Underseal Applied to Entire
• 16 Gauge Outside Panels Understructure
• 16 Gauge Top Panels • Electro Vathodic Emersion Priming
• 14 Gauge End Panels • Automotive Type Non-Porous Door Seals
Mechanically Fastened to the Door Facing
• 18 Gauge Inner Door Panels
• Compartmentation–Curbside:
• 18 Gauge Outer Door Panels
• First Vertical – Two (2) Adjustable Shelves with
• 18 Gauge Shelving, Spangled Steel Dividers on 4” Centers
• 14 Gauge Wheel Panels • Horizontal – One (1) Adjustable Shelf
• 12 Gauge Steel Floor, Formed Checker Plate • Rear Vertical – Seven (7) Adjustable Locking
Swivel Hooks (2-3-2)
• Structural Channel Crossmembers
• Compartmentation – Streetside:
• Master Body Security Locking System
• First Vertical – Two (2) Adjustable Shelves with 4”
• Gas Cylinders for All Vertical Doors
Dividers
• Chains on Horizontal Doors
• Horizontal – Two (2) Fixed Shelves, One Midway
• 108" overall body length and One in the Bottom of Compartment
• 78" Outside Width • Rear Vertical – Two (2) Adjustable shelves with 4”
Dividers
• 40" Body Height
• Slam Action Tailgate
• 15" Compartment Depth
• Treadplate Step Bumper
• 34" Floor Width
• Lights and Reflectors in Accordance with FMVSS
• All Doors are Full, Double Paneled, Self-Sealed with #108 LED Lighting Package, Installed
Built-In Drainage
• Back-Up Alarm
• Stainless Steel Hinge Rods
• Painted One Solid Color
• Stainless Steel Rotary Latches
• Ford F-350, Single Rear Wheel, Automatic
• Door Header Drip Rail at Top for Maximum Weather Transmission
Protection
125
ALTEC MODEL LGS-108-60-DW
standard service body
with dual rear wheel chassis
126
STANDARD FEATURES LGS-108-60-DW
• Fabricated from A40 Grade 100% Zinc Alloy Coated • Metal Formed Fenders
Steel
• Automotive Underseal Applied to Entire
• 16 Gauge Outside Panels Understructure
• 16 Gauge Top Panels • Electro Cathodic Emersion Priming
• 14 Gauge End Panels • Automotive Type Non-Porous Door Seals
Mechanically Fastened to the Door Facing
• 18 Gauge Inner Door Panels
• Compartmentation–Curbside:
• 18 Gauge Outer Door Panels
• First Vertical – Two (2) Adjustable Shelves with
• 18 Gauge Shelving, Spangled Steel Dividers on 4” Centers
• 14 Gauge Wheel Panels • Horizontal – One (1) Adjustable Shelf
• 12 Gauge Steel Floor, Formed Checker Plate • Rear Vertical – Seven (7) Adjustable Locking
Swivel Hooks (2-3-2)
• Structural Channel Crossmembers
• Compartmentation – Streetside:
• Master Body Security Locking System
• First Vertical – Two (2) Adjustable Shelves with 4”
• Gas Cylinders for All Vertical Doors
Dividers
• Chains on Horizontal Doors
• Horizontal – Two (2) Fixed Shelves, One Midway
• 108" Overall Body Length and One in the Bottom of Compartment
• 94" Outside Width • Rear Vertical – Two (2) Adjustable Shelves with 4”
Dividers
• 40" Body Height
• Slam Action Tailgate
• 20" Compartment Depth
• Treadplate Step Bumper
• 54" Floor Width
• Lights and Reflectors in Accordance with FMVSS
• All Doors are Full, Double Paneled, Self-Sealed with #108 LED Lighting Package, Installed
Built-In Drainage
• Back-Up Alarm
• Stainless Steel Hinge Rods
• Painted One Solid Color
• Stainless Steel Rotary Latches
• Ford F-350, Dual Rear Wheel, Automatic
• Door Header Drip Rail at Top for Maximum Weather Transmission
Protection
127
ALTEC MODEL LGS-132-84-DW
standard service body
with dual rear wheel chassis
128
STANDARD FEATURES LGS-108-60-DW
• Fabricated from A40 Grade 100% Zinc Alloy Coated • Automotive Underseal Applied to Entire
Steel Understructure
• 16 Gauge Outside Panels • Electro Cathodic Emersion Priming
• 16 Gauge Top Panels • Automotive Type Non-Porous Door Seals
Mechanically Fastened to the Door Facing
• 14 Gauge End Panels
• Compartmentation–Curbside:
• 18 Gauge Inner Door Panels
• First Vertical – Two (2) Adjustable Shelves with
• 18 Gauge Outer Door Panels Dividers on 4” Centers
• 18 Gauge Shelving, Spangled Steel • Second Vertical – Two (2) Adjustable Shelves with
Dividers on 4” Centers
• 14 Gauge Wheel Panels
• Horizontal – One (1) Adjustable Shelf
• 12 Gauge Steel Floor, Formed Checker Plate
• Rear Vertical – Seven (7) Adjustable Locking
• Structural Channel Crossmembers
Swivel Hooks (2-3-2)
• Master Body Security Locking System
• Compartmentation – Streetside:
• Gas Cylinders for All Vertical Doors
• First Vertical – Two (2) Adjustable Shelves with 4”
• Chains on Horizontal Doors Dividers
• 132" Overall Body Length • Second Vertical – Seven (7) Adjustable Locking
Swivel Hooks (2-3-2)
• 94" Outside Width
• Horizontal – Two (2) Fixed Shelves, One Midway
• 40" Body Height and One in the Bottom of Compartment
• 20" Compartment Depth • Rear Vertical – Two (2) Adjustable Shelves with 4”
Dividers
• 54" Floor Width
• Slam Action Tailgate
• All Doors are Full, Double Paneled, Self-Sealed with
Built-In Drainage • Treadplate Step Bumper
• Stainless Steel Hinge Rods • Lights and Reflectors in Accordance with FMVSS
#108 LED Lighting Package, Installed
• Stainless Steel Rotary Latches
• Back-Up Alarm
• Door Header Drip Rail at Top for Maximum Weather
Protection • Painted One Solid Color
• Metal Formed Fenders • Ford F-350, Dual Rear Wheel, Automatic
Transmission
129
130
N S
T I O
O P
131
ALTEC PRICE LIST
132
ALTEC PRICE LIST
133
ALTEC PRICE LIST
134
ALTEC PRICE LIST
135
ALTEC PRICE LIST
136
ALTEC PRICE LIST
137
ALTEC PRICE LIST
138
WARRANTY PROFILE
WARRANTY.
Products designed and manufactured by Altec Industries, Inc. are warranted to be free from defects
in material and workmanship at the time of initial delivery subject to the following provisions:
For one (1) year following initial delivery of the product, Altec will, at its option, repair or
replace any part found by Altec to be defective in material or workmanship at the time of the
initial delivery. During the first ninety (90) days following initial delivery, no charge for parts,
labor or travel to the customer's location shall be made for such repair or replacement at the
customer's location. During the remainder of such one (1) year, no charge for parts or labor
shall be made for such repair or replacement at an Altec service facility.
This limited warranty does not cover: (a) products which have not been operated and main-
tained in accordance with Altec operators and maintenance manuals, programs and bulletins;
(b) products which have not been mounted in accordance with Altec installation procedures;
(c) products not manufactured by Altec which are supplied by Altec on special order; (d) prod-
ucts which are repaired without using original Altec parts; or (e) transportation or delivery to
an Altec service facility or the customer's location.
DOMESTIC USE.
When vehicles are used within the continental United States, the warranty shall include the furnish-
ing, without cost to the Government (FOB Altec's nearest dealer or branch to vehicle's location or station),
of new parts and assemblies to replace any that failed or malfunctioned within the warranty period. In
addition, when the Government elects to have the work performed at Altec's plant, branch, dealership,
or with Altec's approval (i) to correct the supplies itself; or (ii) to have them corrected by a commercial
garage facility; the cost of the labor involved in the replacement of the failed or malfunctioned parts or
assemblies shall be borne by Altec.
FOREIGN USE.
When vehicles are used outside the continental United States, including Puerto Rico and the Virgin
Islands, the warranty shall include the furnishing of new parts or assemblies to replace any returned to
Altec by the Government that failed or malfunctioned within the warranty period. The replacement parts
or assemblies shall be delivered by Altec to the port of embarkation in the United States designated by
the Government. Altec will not be required to bear the cost of the labor involved in correcting defects in
vehicles operated in foreign countries.
WARRANTY EXCEPTIONS.
The following items are considered normal maintenance and repair for which Altec need not assume
liability for reimbursing the Government regardless of the vehicle age or mileage.
139
ALTEC INSTALLATION CENTERS
1. Altec Industries, Inc. . . . . . Southern Operation 7. Altec Industries, Inc. . South Eastern Operation
1730 Vanderbilt Road (35234) 1550 Aerial Avenue
P.O. Box 10264 Creedmoor, NC 27522
Birmingham, AL 35202 (919) 528-2535
(205) 323-8751
8. Altec Industries, Inc. . . . . . . Roanoke Operation
2. Altec Industries, Inc. . . . . . . Western Operation 325 South Center Drive
325 Industrial Way Daleville, VA 24083
Dixon, CA 95620 (540) 992-5300
(916) 678-0800
9. Altec HiLine, LLC . . . . . . . . . . HiLine Operation
3. Altec Industries, Inc. . . . . . . Midwest Operation P.O. Box 16288
2106 South Riverside Road Duluth, MN 55816-0288
St. Joseph, MO 64507-9799 1255 Port Terminal Drive
(816) 364-2244 Duluth, MN 55802
(218) 722-9200
4. Altec Industries, Inc. . Elizabethtown Operation
200 Altec Drive 10. Altec Industries, Inc. . . . . Burnsville Operation
Elizabethtown, KY 42701 150 Altec Drive
(270) 360-0600 Burnsville, NC 28714
(828) 678-5500
5. Altec Industries, Inc. . . . . . . . Eastern Operation
250 Laird Street 11. Altec Environmental Products
Plains, PA 18705 512 North Post Road
(717) 822-3104 Shelby, NC 28150
(704) 482-4356
6. Altec Industries, Inc. . . . . . . Northern Operation Fax (704) 482-5926
5201 West 84th Street
P.O. Box 681308
Indianapolis, IN 46268
(317) 872-3460
140
ALTEC SERVICE CENTERS
1. Altec Service Center. . . . . . . . . . . . . . . Alabama 10. Altec Service Center. . . . . . . . . . . . . . . Missouri
1730 Vanderbilt Road 5202 E. 36 Highway
Birmingham, AL 35239 St. Joseph, MO 64507
(205) 458-1599 (816) 236-1219
4. Altec Service Center. . . . . . . . . . . . . . . . Oregon 13. Altec Service Center. . . . . . . . British Columbia
13817 NE Sandy Blvd. 12352 84th Avenue
Portland, OR 97230 Surrey, British Columbia V3W 0J5 Canada
(503) 253-3900 (604) 597-0355
9. Altec Service Center. . . . . . . . . . . . . . Maryland 18. Altec Industries, Inc. . South Eastern Operation
1434 Hughes Ford Road 1550 Aerial Avenue
Frederick, MD 21701 Creedmoor, NC 27522
(301) 662-6262 (919) 528-2535
141
OPTIONAL EXTERIOR COLORS FOR CHASSIS
NOTE: (1) DUE TO THE LIMITATIONS OF PRINTING PROCESSES, SOME COLORS MAY VARY.
142
Version 1.2, Printed July 2008