Professional Documents
Culture Documents
387022P-EN R13 SIGA-CC1 Single Input Signal Module Installation Sheet
387022P-EN R13 SIGA-CC1 Single Input Signal Module Installation Sheet
Installation Sheet
Personality codes
Use the personality codes described below to configure the
SIGA-CC1 module. See Table 1 for listing information
© 2017 United Technologies Corporation 1/6 P/N 387022P-EN • REV 13 • ISS 14MAR17
• This module does not operate without electrical power. As Figure 2: Bell circuit showing bipolar transient protector
fires frequently cause power interruption, discuss further placement
safeguards with the local fire protection specialist.
(1) (2)
To install the module:
1. Write the address assigned to the module on the label
provided, and then apply the label to the module. Remove
the serial number label from the module, and then attach it
to the project documentation.
2. Connect the field wires. See “Wiring” below.
10 9
3. Using the self-tapping screw, attach the wall plate to the
(1) Normal state (2) Active state
module. See Figure 1.
4. Using the four machine screws, attach the wall plate and Wiring
module to the electrical box.
Wire this device in accordance with applicable national and
Figure 1: Installing the SIGA-CC1 module local codes, ordinances, and regulations.
(5)
+
(1)(2)(3)(4)
+ +
(10) (6)
+
+ (7)
(9)
(3)(8)
(1) Signal polarity is shown when the circuit is in supervisory state. (4) If using a G1-P Genesis series horn while connected to a
Polarity reverses when the circuit is active. compatible fire alarm control panel, a CDR-3 Bell Coder must
(2) Supervised. be used to comply with NFPA 72 standard alarm evacuation
(3) Power-limited unless connected to a nonpower-limited source. If signal.
the source is nonpower-limited, eliminate the power-limited mark (5) 47 kΩ EOLR.
and maintain a minimum of 0.25 in. (6.4 mm) space from power- (6) Signaling line circuit (SLC) to next device.
limited wiring. For other mounting methods, see enclosure and (7) AUX riser (to next module or riser supervisory device).
bracket installation sheets to maintain separation of power- (8) Power-limited regulated, power supply UL/ULC Listed for fire
limited and nonpower-limited wiring. The wire size must be protective signaling systems.
capable of handling fault current from nonpower-limited source. (9) AUX riser (from previous device).
— or — (10) Signaling line circuit (SLC) from previous device. Supervised
Use type FPL, FPLR, FPLP, or permitted substitute cables, and power-limited.
provided these power-limited cable conductors extending beyond
the jacket are separated by a minimum of 0.25 in. (6.4 mm)
space or by a nonconductive sleeve or nonconductive barrier
from all other conductors. Refer to the NFPA 70 National
Electrical Code for more details.
(5)
(1)(2)(3)(4)
+ +
(10) (6)
+
(7)
+
(9)
(1) Signal polarity shown when the circuit is in supervisory state. (4) Unshielded twisted pair.
Polarity reverses when the circuit is active. (5) 47 kΩ EOLR (P/N EOL-47).
(2) Supervised. (6) Signaling line circuit (SLC) to next device.
(3) Power-limited unless connected to a nonpower-limited source. If (7) Audio riser (to next module or supervisory end of line device).
the source is nonpower-limited, eliminate the power-limited mark (8) Unshielded twisted pair. Use shielded twisted pair when
and maintain a minimum of 0.25 in. (6.4 mm) space from power- installed in the same conduit as with a telephone riser.
limited wiring. For other mounting methods, see enclosure and (9) Audio riser (from previous device).
bracket installation sheets to maintain separation of power- (10) Signaling line circuit (SLC) from previous device. Supervised
limited and nonpower-limited wiring. The wire size must be and power-limited.
capable of handling fault current from nonpower-limited source.
— or —
Use type FPL, FPLR, FPLP, or permitted substitute cables,
provided these power-limited cable conductors extending beyond
the jacket are separated by a minimum of 0.25 in. (6.4 mm)
space or by a nonconductive sleeve or nonconductive barrier
from all other conductors. Refer to the NFPA 70 National
Electrical Code for more details.
(5)
(1)(2)(3)
(4)
(10) (6)
(9) (7)
(3)(8)