Professional Documents
Culture Documents
ERROR CODES
The Electronic Instrument Cluster (EIC) features These error codes appear when any one of the
an integral fault diagnosis system which displays listed errors occurs. The alarm sounds
error codes on the LCD as shown in the following continuously for a critical alarm and for 5 seconds
Table. with a non critical alarm.
EIC DISPLAY
SENSOR COND T ON ALARM
Less han 500 rev m n More han 500 rev m n
Error Code No
O Sende
C ca
Sho o G ound Open C cu
O Sende
C ca
Sho o a +ve Vo age
Fue Sende
Non C ca
Sho o Ea h G ound
Fue Sende
Non C ca
Open C cu o Sho o a +ve Vo age
Ax e S a Sende
Non C ca
Sho o Ea h G ound
Ax e S a Sende
Non C ca
Open C cu o Sho o a +ve Vo age
Coo an Tempe a u e Sende
Non C ca
Sho o Ea h G ound
E ec on c D a Con o e o
Se a L nk Fa u e
T ansm ss on e o
Se a L nk Fa u e
Ba e y Ca b a on e o
S p A a m S p cons an
Non C ca
W d h and Se v ce Hou s check
Coo an Tempe a u e Sende
C ca
open c cu o sho ed o a +ve Vo age
Eng ne Shu down e o
604.55.041.00 - 01 - 1998
14 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2
At connector, C003,
measure voltage between Replace
Check for faulty cable between cable
C001--S--FM2014--G/K/C081--5--CM2014--G/K, +5 and Ground pins
C001--A--FM31--Y/S/C081--6--CM31--Y/S and Is voltage approx. 5v?
C001--J--FM2095--G/W/B /
C081--9--CM2095--G/W/B,
Is cable O.K? Replace
sender
Replace Replace
EIC cable
604.55.041.00 - 01 - 1998
SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2 15
604.55.041.00 - 01 - 1998
16 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2
Inspect instrument
panel connectors. Are Substitute instrument panel for one of
connectors okay? known performance and recheck.
Repair connector as
required.
604.55.041.00 - 01 - 1998
SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2 17
604.55.041.00 - 01 - 1998
18 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2
604.55.041.00 - 01 - 1998
SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2 19
The Electronic Draft Control module and the electronic transmission control (processor) send their disply
information over a two wire serial communications connection.
Communications errors (8&9) occur when the message received by the instrument panel is not correct. This
can be caused by an intermittent connection on the signal wires (LN/O orLN/TQ). If these errors are
accompanied by reports of intermittent or blank displays in the transmission or hitch position areas, then the
circuit wires should be investigated for open circuits, short circuits and intermittent connections.
LN/O C128--35
C080--19
EIC LN/TQ
EDC/TRANS.
C080--20 C128--14
Compare the voltage display of instrument panel to a voltmeter reading at the battery. If the readings differ
by more than 2.0 volts, then replace instrument panel and recheck.
ERROR CODE 11 -- Memory Retention Error of Operator Setting for Slip Alarm, Slip
Zero Reference Constant, Implement Width and Service Hours
604.55.041.00 - 01 - 1998
20 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2
Clean the connector pins with Find and repair an open circuit fault in wiring
contact cleaner spray Apply a between connectors C079--8 (instrument panel)
dielectric grease. Reconnect and connector C012 (sender)
plugs to the instrument cluster
and turn keystart switch on
Does the cluster function Install a new Instrument Panel and recheck
correctly? function.
604.55.041.00 - 01 - 1998
SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2 21
Figure 1
604.55.041.00 - 01 - 1998
22 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2
Common Test Procedure for ALL of the Switch Circuits Connecting to Ground
Disconnect the harness at the Check the ground path of the switch and
sender/switch, and connect signal wire to recheck function.
ground Is the resistance to ground less than
Is the warning light illuminated? 10 !?
Is the
warning
light
illuminated?
604.55.041.00 - 01 - 1998
SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2 23
604.55.041.00 - 01 - 1998
24 SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2
DIAGNOSTIC MEMORY
30
31
604.55.041.00 - 01 - 1998
SECTION 55 -- ELECTRICAL SYSTEM -- CHAPTER 2 25
’0’ ’7’
’7’ = Byte number
’0’ or ’1’ = Function
33
Use the DIGIT SELECT function switch to select next Byte (15 -- 0).
Use the DIGIT SET function switch to select function of Byte (’0’ or ’1’).
BYTE No.
604.55.041.00 - 01 - 1998