Professional Documents
Culture Documents
MODULAR QUIZ - 54 - Steel Design
MODULAR QUIZ - 54 - Steel Design
Design
Total points5/20
SUBJECT CODE: VTH54B#
Email*
cornelio.fernandez1096@gmail.com
0 of 0 points
What is your full name? (LAST NAME, GIVEN NAME M.I.)*
FERNANDEZ, CORNELIO III J.
What school did you graduated from? (FULL NAME OF YOUR SCHOOL)*
LYCEUM OF THE PHILIPPINES UNIVERSITY - CAVITE
SITUATION 1:
1 of 3 points
An I beam whose flange width is 357mm, flange thickness is 15mm, web thickness is 20mm,
total depth of 450mm and Fy of 248MPa is to be used to carry a uniform load all throughout its
length, 3m.
1. What is the allowable bending stress?*
1/1
a. 153.69 MPa
b. 161.75 MPa
c. 192.69 MPa
d. 168.23 MPa
2. Determine the moment of inertia of the section.*
0/1
Correct answer
c. 0.630 x 10⁹ mm⁴
3. What is the maximum safe uniform load that the beam could carry?*
0/1
a. 402.58 kN/m
b. 164.6 kN/m
c. 476.56 kN/m
d. 541.6 kN/m
Correct answer
a. 402.58 kN/m
a. 151 kN/m
b. 122 kN/m
c. 146 kN/m
d. 162 kN/m
Correct answer
c. 146 kN/m
5. Which of the following most nearly gives the maximum uniform load on the 8m
simple span beam (W21x57) so that the allowable bearing stress in bolt holes will not
be exceeded?*
0/1
a. 73.7 kN/m
b. 74.4 kN/m
c. 57.9 kN/m
d. 83 kN/m
Correct answer
a. 73.7 kN/m
6. Which of the following gives the maximum safe uniformly distributed load that the
said beam could carry?*
1/1
a. 73.7 kN/m
b. 74.4 kN/m
c. 57.9 kN/m
d. 83 kN/m
SITUATION 3:
1 of 5 points
A simply supported beam with a span of 8 m is subjected to a uniform vertical downward load
equal to 50 kN/m, acting on the plane of the minor axis of the beam section, which includes the
beam weight. The beam is restrained against lateral buckling of the top and bottom flanges for
the entire span. The material is A36 steel with Fy = 248 MPa and E = 200 GPa. The allowable
flexural stress for laterally braced compact sections is 0.66Fy. The allowable deflection is 1/360
of the span.
7. Determine the minimum section modulus Sx, in m³, such that the maximum flexural
stress will not be exceeded.*
0/1
a. 0.0024
b. 0.0038
c. 0.0042
d. 0.0052
Correct answer
a. 0.0024
8. Determine the minimum moment of inertia Ιx, in m ⁴, such that the minimum deflection
will not be exceeded.*
0/1
a. 0.00096
b. 0.00047
c. 0.0024
d. 0.00060
Correct answer
d. 0.00060
9. Assuming that the shear stress is not critical, which of the sections being considered
is the most economical section for the given load.*
0/1
a. W 24x55
b. W21x62
c. W 21x68
d. none
Correct answer
d. none
PROBLEM 10: A 10 m steel wide flange beam is laterally supported. The depth of the
beam is 700 mm and web thickness is 10 mm. If Fy is equal to 250 MPa. Find the the
allowable bending stress if compression flange is stiffened.*
0/1
a. 135 MPa
b. 165 MPa
c. 185 MPa
d. 105 MPa
Correct answer
b. 165 MPa
PROBLEM 11: The shear capacity V if a steel wide flange section, 600 mm deep whose
web is 9 mm thick, is closest to: Assume fy = 200 MPa. Take FV = 0.4 Fy*
1/1
a. 645 kN
b. 413 kN
c. 507 kN
d. 432 kN
SITUATION 4:
1 of 3 points
A W 310 x 38 steel beam having a span of 6 m is resting on a W 530 x 82 girder. The beam
carries a super imposed load of 4875 Pa excluding the weight of a 100 m concrete slab and its
own weight. Weight of concrete is 23.5 kN/m³. Use A36 steel with yield strength Fy = 248.8
MPa. The compression flange is rigidly attached to the concrete floor.
Properties of W 310 x 38
12. Which of the following gives the allowable bending stress.*
0/1
a. 135.58 MPa
b. 164.21 MPa
c. 175.26 MPa
d. 185.36 MPa
Correct answer
b. 164.21 MPa
13. Which of the following gives the total load that can be carried by the beam in kN.*
0/1
a. 150.7 kN
b. 136.4 kN
c. 120.2 kN
d. 248.7 kN
Correct answer
c. 120.2 kN
14. Which of the following gives the spacing of the W 310 x 38 beam?*
1/1
a. 2.7 m
b. 4.5 m
c. 3.6 m
d. 1.8 m
SITUATION 5 :
0 of 3 points
An I beam whose flange width is 375mm, flange thickness is 15mm, web thickness is 20mm,
total depth of 450mm and Fy of 248MPa is to be used to carry a uniform load all throughout its
length,3m.
15. What is the allowable bending stress?*
0/1
a. 563.6 MPa
b. 127.6 MPa
c. 192.9 MPa
d. 159.8 MPa
Correct answer
d. 159.8 MPa
16. Determine the moment of inertia of the section.*
0/1
Correct answer
a. 0.656 x 10⁹ mm⁴
17. What is the maximum safe uniform load that the beam could carry?*
0/1
a. 123.6 kN/m
b. 764.6 kN/m
c. 414.14 kN/m
d. 541.6 kN/m
Correct answer
c. 414.14 kN/m
SITUATION 6 :
1 of 3 points
A beam having a simple span of 6 m is loaded with a uniform load acting on the plane of the
minor axis of the beam section. The beam is restrained against lateral buckling of the top and
bottom flanges for the entire span. Fy = 250 MPa, E = 200000 MPa
Allowable stresses:
Flexural or bending stress = 0.66Fy
Shear stress = 0.40 Fy
Allowable deflection = 1/360 of span
Properties of Steel Section: Ix = 560x 10⁶ mm ⁴, d = 550 mm, tw = 10 mm
18. Which of the following gives the maximum uniform load if the allowable flexural
stress governs.*
1/1
a. 76.47 kN/m
b. 74.67 kN/m
c. 47.76 kN/m
d. 64.76 kN/m
19. Which of the following gives the maximum uniform load if the allowable shear stress
governs.*
0/1
a. 151.32 kN/m
b. 138.38 kN/m
c. 125.15 kN/m
d. 183.33 kN/m
Correct answer
d. 183.33 kN/m
20. Which of the following gives the maximum uniform load if allowable deflection
governs.*
0/1
a. 110.62 kN/m
b. 112.26 kN/m
c. 121.10 kN/m
d. 162.10 kN/m
Correct answer
a. 110.62 kN/m