Professional Documents
Culture Documents
Switch 560NUS12
RTU560 product line
• Unmanaged switch
• 2x SFP slot, without optical transmitter/
receiver
• Additional SFP modules are required
• 2x 10/100 BaseT port (electrical)
• Linear network structure supported
Application Characteristics
The RTU component 560NUS12 is an unmanaged plug For documentation purposes the Ethernet ports are
and play 10/100 Mbps Ethernet switch providing 2 fast labeled from 1 to 4 with 1 & 2 for the RJ45-Ports and 3
Ethernet autonegotiating RJ45-ports with auto MDI/ & 4 for the fiber optic SFP slots.
X (automatic crossover detection and correction) and
2 fiber optic 100 Mbps slots for use with SFP (small There is no specific Uplink port; Ports 1 and 2
form-factor pluggable) modules. respectively 3 and 4 are equal in function. Status
indicators display the link and speed status of each
The switch is intended for distributing Ethernet within port (refer to Connectors and Indicators).
a station through the RJ45-ports. The fiber optic
ports can be used for interconnecting stations with a The Switch learns Ethernet addresses by analyzing
maximum distance of 40 km. received frames. Addresses learnt are stored in a
lookup-table (max. 1024 entries) that is used to
forward frames only to the correct port. A received
frame is forwarded to all ports expect the receiving
Transformer Transformer
560NUS12
Device
Device
itself. Figure 2: Left: Topology not applicable for 560NUS12 / Right: Typical
topology for use with 560NUS12
Topology
The 560NUS12 Switch provides a total of four Ethernet
ports for use with end devices, switches, bridges, hubs
or routers. Star or line topologies can be easily built by
the 560NUS12 Switch.
Technical data Mechanical layout
Dimensions 160 mm x 100 mm, 3HE
euro card format
Power 4R (20 mm) front panel
Operating Voltages 5 VDC ± 10% Housing type Printed circuit board
Power Consumption Typ. 1.55 W, max. 2.00 W Mounting for mounting in RTU560
racks
(Both RJ45 port active, no
SFP modules) Weight 130 g
Additional Power
Consumption per SFP
module Connection type
500SMM02 550 mW RTU560 backplane 48 pole type F DIN 41612
connector
500SSM15 875 mW
500SSM40 9/125 µm
Immunity test
min./max. optical output
Electrostatic discharge 8 kV air / 6 kV contact
power
IEC 61000-4-2 (level 3)
500SMM02 -19 dBm / -14 dBm
Performance criteria A
500SSM15 -15 dBm / -8 dBm
Electrical fast transient / 4 kV (level 4)
500SSM40 -5 dBm / 0 dBm Burst
IEC 61000-4-4 Performance criteria A
max. receiver sensitivity
Surge 4 kV (level 4)
500SMM02 -31 dBm IEC 61000-4-5
Performance criteria A
500SSM15 -34 dBm
Damped oscillatory wave 2.5 / 1 kV (level 3)
500SSM40 -34 dBm IEC 61000-4-18
Performance criteria A
approx. fiber optic cable
length
500SMM02 2 km Ethernet
Green LED
Alarm
Cable Type EIA/TIA Category 3 or ISO/
Status Indicator Red LED, label: ERR IEC Class C cable or better
Relais Contact Isolated Change Over for 10 Mbps
Contact
Relais max. Switching DC 60 VDC / 0,5 A
EIA/TIA Category 5 or ISO/
Voltage / Current
AC 250 VAC / 0,24 A IEC Class D cable or better
for 100 Mbps
Max. Cable Length 100 m
Ethernet Accessories ordering information
Protocol Fast-Ethernet according 500SSM40 SFP Module single-mode
to IEEE 802.3-2005 Cl. 25 500SSM40 R0001 1KGT038914R0001
and IEEE 802.3u-1995
long range up to 40 km
Auto-Negotiation
(NWAY) according to IEEE
802.32005 Cl. 28
Auto-Crossover (Auto
MDI/X)
Switching
Flow Control Full Duplex Flow Control
according to IEEE
802.32005 An. 31B and
IEEE 802.3x-1997
Half Duplex Back Pressure
Max. Frame size 1552 Bytes
Quality of Service IEEE 802.1p Tag based
Priority
High/Low Priority Queue
with 16:1 service rate
MAC Lookup Table Max. 1024 entries
Ordering information
560NUS12 R0001 1KHW001892R0001
short range up to 2 km
intermediate range up to
15 km
ABB AG We reserve the right to make technical We reserve all rights in this document and in
1KGT 150 632 V005 1
Power Grids changes or modify the contents of this the subject matter and illustrations contained
P.O. Box 10 03 51 document without prior notice. With therein. Any reproduction, disclosure to third
68128 Mannheim, Germany regard to purchase orders, the agreed parties or utilization of its contents – in whole
Tel. +49 621 381-3000 particulars shall prevail. ABB AG does not or in parts – is forbidden without prior written
accept any responsibility whatsoever consent of ABB AG. Copyright© 2019 ABB AG
for potential errors or possible lack of All rights reserved
www.abb.com/remote-terminal-units information in this document.