Professional Documents
Culture Documents
MACHINE GUN
1) MACHINE GUN M87
The complete set of machine gun M87 consists of the following items:
DESCRIPTION OF MACHINE GUN М02 - machine gun M87 (fig.2),
- accessories (fig.3),
Chosen version of infantry machine gun consists of five structural parts: - spare parts (fig.4),
- three ammunition boxes,
- 36 belts for 12.7 mm or .50 Browning cartridge
3
Accessories of machine gun M87 Spare parts set
4
Stripping of machine gun M87 Sequence of stripping of machine gun
Striping of machin gun M02 Coyote to its structural assemblies Open the feed block cover - Push the cover catch upward, open
is described in user manual and from that resaon in this book is the cover, and raise it all the way up (Fig. 5).
described stripping of machine gun M87 only.
Fig. 7 Fig. 8
5
Fig. 9
Fig. 11
Raise the ejector body together with ejector (Fig. 10) into
vertical position. To remove the bolt carrier with bolt: By means of the cocking
handle pull the bolt carrier into rear position and separate it
from the receiver by lifting up (Fig. 12).
Fig. 10
To remove the recoil mechanism with buffer: lift the buffer
body behind the lug on the receiver, and separate the recoil Fig. 12
mechanism from the receiver (Fig. 11) Separate the cocking handle by pulling into rear position and
removing to the right (Fig. 13).
6
To remove the barrel from receiver: Pull the securing key handle
(Fig.14) to the right and bring the carrying handle into carrying
position. To achieve this it is necessary to press the button (Fig.
15) and pull the handle half-way down, then raise it, release
backward and block the handle lock; finally pull the handle
forward and separate the barrel from receiver (Fig.16).
Fig. 13
Fig. 16
Fig. 14
Fig. 15
7
Replacement of the parts (included in spare parts set)
Spare barrel
Bring the cleaning rod with handle into vertical position and fit
the recoil mechanism onto it. Tighten the recoil spring from the Fig. 17
top and separate the securing ring from the front guide, sepa-
rate the recoil spring and front guide from the rear guide, and Ejector spring
finally separate the buffer spring.
Ejector serves to push the cartridge case along the bolt body
face surface after extraction from the cartridge chamber.
Ejector with its spring is fixed to the left-hand side of the receiver
by a pin. It has two spring-loaded arms: the front is used for car-
tridge case ejection and the rear one for engagement with the
8
bolt carrier moving into rear position. To separet spring from
ejector press the spring using drift (Fig. 18)
Fig. 19 Fig. 20
Fig. 18
Fig. 21
Cartridge case extractor, upper and lower and extractor
spring
Push bolt lock pin fully and release the right coupling (Fig. 19),
turn the bolt on the other coupling to the left, by means of the
punch drive the extractor / firing pin securing pin out supporting
the bolt and extractors by the hand, and separate the extractors
with springs from the bolt. (Fig. 20 to Fig. 22). Using the punch
drive the firing pin out of the bolt (Fig. 23), drive the cartridge case
retainer pin out supporting the bolt and cartridge case retainers
by the hand and separate the cartridge case retainers with springs. Fig. 22 Fig. 23
9
Feeding pawls spring
Stripping of feed block cover: Using the punch drive the guard
shaft out of engagement with the eyelet and move it aside, and
then separate the guard (Fig.24). Remove the feed port cover
previously driving its axle out and separating the cover from
the feed block cover.
Fig. 25 Fig. 26
Fig. 24
To separate the feed arm and feed slide with feed pawls and
spring use the wrench to release the front end of the feed arm, Fig. 27
spring ; remove the feed arm spring and feed arm retaining
spring; by means of the punch drive the front link retainer pins
out and separate the retainer from the cover; separate the feed
arm with coupling and link retainer from the shaft ; separate
the feed slide with feed pawls and spring; drive the feed pawls
shaft out and separate the feed pawls from the feed slide.
Fig. 28
10
Spare parts of Coyote mount Replacement of buffer spring and cocking rope
Fig. 30
After that unscrew nuts to change buffer spring (Fig. 31 and Fig
32)
11
To replace cocking rope unscrew its fixing nut as shown on Fig.
33 and after that replace cocking rope (Fig. 34). Length of cock-
ing rope adjust in that manner to enable undisturbed move-
ment of support in front positon by its recoil spring (Fig.35).
Fig. 33 Fig. 34
Fig. 35
12
STOPPAGES IN FIRING AND HOW TO ELIMINATE THEM
Incomplete Incomplete movement of cartridge case Eject the cartridge case by repeated
return of movable parts backward within bolt grooves which may make loading. Set gas regulator to division
the case “fall” into barrel holder during “2”. In case of repeated stop- page,
bolt carrier travel into extreme front clean the paths and sliding surfaces.
position
Dirty machine gun, particularly gas
paths
13
Jamming of movable parts Foreign objects in machine gun or Remove foreign objects or broken
broken parts of machine gun parts. Inspect machine gun, replace
broken part by a spare one from
accessories. If such a part is not
contained in the accessories, send
machine gun to repair shop. Clean
damaged and kicked surfaces
Cartridge case is not ejected or gets Incorrect extractors or broken extractor Move cartridge case in bolt grooves
jammed in bolt grooves; movable parts springs. fully to the right while retaining
remain in intermediate position. movable parts, eject the case and
proceed with firing. If the stoppage
recurs replace extractors
Cartridge case is not held by extractor Broken extractor lug or spring. Remove cartridge case and replace
lug. Moving into front position broken spring. If one of the extractors is
mova¬ble parts strike against cartridge broken, replace both extractors
case.
Round being loaded into chamber gets Round incompletely spripped by belt Pull movable parts onto disconnector,
jammed between bolt and feed block link stripper due to incom¬plete return raise cover, remove belt, take defective
base of movable parts. round out, reload and proceed with
firing. If the stoppage recurs, set gas
regulator to division “2”.
Misfeeding. The next round did not Broken or weakened feed pawl springs Replace springs, remove defective belt
reach feed port and fixing pawl springs. Defective links. links.
Empty belt link gets under link stripper Cartridge belt is not properly loaded Bring movable parts onto disconnector.
and rounds fail out of it during firing Raise cover, remove belt from feed
block cover, reload machine gun and
proceed with firing.
14
15
Zastava oružje AD
Kosovska 4,
34000 Kragujevac
Serbia
www.zastava-arms.rs
e-mail> office@zastava-arms.rs