Professional Documents
Culture Documents
i2300H Please read all instructions carefully before using the IC-
2300H.
This instruction sheet describes only basic operations. For more detailed instructions, go to our web site (URL: http://www.icom. ■ Microphone (HM-154)
co.jp/world/index.html) to view or download the full IC-2300H instruction manual.
In the instruction manual, some options or some functions may not be available for this version. Please ask your dealer for details. w q PTT SWITCH
Hold down to transmit; release to receive.
Microphone element
w UP/DOWN KEYS [UP] or [DN]
■ Precautions ➥ Push either key to change the operating frequency,
ON
RWARNING RF EXPOSURE! This device emits Ra- CAUTION: NEVER expose the transceiver to rain, snow q e
memory channel, Set mode setting, and so on.
dio Frequency (RF) energy. Extreme caution should be observed or any liquids. The transceiver may be damaged. ➥ Hold down either key for 1 second to start scanning.
OFF
when operating this device. If you have any questions regarding RF e UP/DOWN LOCK SWITCH
exposure and safety standards, please refer to the Federal Com-
DO NOT push the PTT when not actually intending to transmit. Slide to lock the [UP]/[DN] keys.
munications Commission Office of Engineering and Technology’s KEEP the transceiver out of the reach of children.
report on Evaluating Compliance with FCC Guidelines for Human
Radio frequency Electromagnetic Fields (OET Bulletin 65). During mobile operation, DO NOT operate the transceiver
without running the vehicle’s engine. When the transceiver’s
RWARNING! NEVER connect the transceiver to an AC power is ON and your vehicle’s engine is OFF, the vehicle’s bat-
outlet. This may pose a fire hazard or result in an electric shock. tery will soon become exhausted.
RWARNING! NEVER cut the DC power cable be- BE CAREFUL! The transceiver will become hot when op-
tween the DC plug and fuse holder. If an incorrect connection is erating it continuously for long periods of time. ■ Basic operation
made after cutting, the transceiver may be damaged.
DO NOT set the transceiver in a place without adequate ven-
RWARNING! NEVER operate the transceiver while tilation. Heat dissipation may be affected, and the transceiver [ ]
[VOL] Noise squelch
• [SQL] control
driving a vehicle. Safe driving requires your full attention—any- [S.MW] (MW) Squelch
may be damaged. [DIAL] threshold
thing less may result in an accident.
DO NOT use or place the transceiver in direct sunlight or in areas Squelch attenuator
RWARNING! NEVER
[BANK] (OPT)
connect the transceiver to a with temperatures below –10°C (+14˚F) or above +60°C (+140˚F). or
[SQL] Squelch is S-meter squelch
power source of more than 16 V DC or use reverse polarity. This [SET] (LOCK) [V/MHz] (SCAN)
could cause a fire or damage the transceiver. DO NOT use harsh solvents such as benzine or alcohol
[MONI] (ANM PA) [M/CALL] (PRIO)
open.
when cleaning, as they will damage the transceiver’s surfaces.
RWARNING! NEVER operate or touch the transceiver [LOW] (DUP) [TONE] (T-SCAN) Shallow Deep
with wet hands. This may result in an electric shock or damage USE only Icom microphones (supplied or optional). Other
D Turning power ON/OFF D Squelch attenuator
manufacturer’s microphones have different pin assignments and
the transceiver.
may damage the transceiver if attached. ➥ Hold down [ ] for 1 second to turn the power ON or OFF. The transceiver has an RF attenuator related to the squelch
RWARNING! NEVER place the transceiver where D VFO mode selection level setting. Approximately 20 dB of attenuation is obtained
normal operation of the vehicle may be hindered or where it Approved Icom optional equipment is designed for optimal per- at the maximum setting.
could cause bodily injury. formance when used with an Icom transceiver. The IC-2300H has two basic operating modes; the VFO
Icom is not responsible for the destruction or damage to an Icom mode and the memory mode.
RWARNING! NEVER let metal, wire or other objects transceiver in the event the Icom transceiver is used with equip- ➥ Push [V/MHz] to select the VFO mode.
Turn ON the Squelch Attenuator function:
touch any internal part of the transceiver. This may result in an ment that is not manufactured or approved by Icom. q Push [ ] to turn OFF the power.
• Push [M/CALL] one or more times to select the memory,
electric shock. w While holding down [LOCK] (SET), hold down [ ] for
Call or marine channel* mode.
1 second to turn ON the power and enter the Initial Set
e Rotate [DIAL] to select a marine or memory channel to pauses when a signal is received on the Priority channel.
be added. • Tri-watch*
DIGITAL PRIO AO BUSY Tri-watch monitors the
■ Memory channels
Selected MUTE
NAR
channel MID
LOW
Priority channel and Ch 88 Ch 16† Ch 88 Ch 9*
LOCK ANM DUP T-SCAN PRIO SCAN
SET MONI LOW TONE M/CALL V/MHz
the Call channel while
The IC-2300H has a total of 207 memory channels for stor-
r Hold down [MW] (S.MW) for 1 second. receiving on a TAG
ing often used operating frequencies, repeater settings, and channel.
• 3 beeps sound and the selected channel is added. †
so on. Memories include 6 scan edges and 1 Call channel. Tri-watch switches to Priority channel *Call channel
D Clearing TAG channels Dualwatch, when receiving a signal on the Call channel.
D PROGRAMMING MEMORY CHANNELS The programmed TAG channels can be cleared as a TAG channel. *One or more TAG channels other than the Call and Priority chan-
1. Setting the frequency nels must be programmed, to start the Tri-watch.
3. Writing the memory channel q Push [M/CALL] one or more times to select the marine
In the VFO mode, set the desired operating frequency, re- Hold down [MW] (S.MW) for 1 second to program. channel mode.
peater, tone, tuning steps, and so on. • 3 beeps sound w Rotate [DIAL] to select the marine channel to be cleared. Start the watch:
• The memory channel number automatically increases when e Hold down [MW] (S.MW) for 1 second. q Push [M/CALL] one or more times to select the marine
2. Selecting the memory channel continuing to hold down [MW] (S.MW) after programming. • 3 beeps sound and the selected channel is cleared. channel mode.
Push [S.MW], and then rotate [DIAL] to select the desired w Hold down [OPT] (BANK) for 1 second, to enter the Ma-
rine Set mode.
memory channel. D Setting the Call/Priority channel
e Push [SET] or [MONI] until “PRI” appears.
• The “ ” icon and memory channel number blink. D Selecting Memory channel Set a TAG channel as the Call or Priority channel. r Rotate [DIAL] to select the Watch type.
MUTE
DIGITAL PRIO AO BUSY q Push [M/CALL] one or more times to select the memory q Push [M/CALL] one or more times to select the marine • “PR” : Priority watch
NAR
MID
LOW
mode. channel mode. • “DU” : Dualwatch
w Hold down [OPT] (BANK) for 1 second, to enter the Ma-
LOCK ANM DUP T-SCAN PRIO SCAN
SET MONI LOW TONE M/CALL V/MHz • The “ ” icon appears. • “TR” : Tri-watch.
[S.MW] [DIAL] w Rotate [DIAL] to select a desired memory channel. rine Set mode. t Push any key other than [SET], [MONI] or [BANK], to
• Only programmed memory channels can be selected. e Push [SET] or [MONI] until the “M–” and “C” or “M–” and save the setting and exit the Marine Set mode.
“P” appear. y Hold down [M/CALL] (PRIO) for 1 second to start the
DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY
MUTE MUTE watch.
■ Set mode ■ Repeater operation
NAR NAR
MID MID
LOW
LOCK
SET
ANM
MONI
DUP T-SCAN PRIO SCAN
LOW
LOCK
SET
ANM
MONI
DUP T-SCAN SCAN • The “PRIO” icon appears.
Setting the Call channel Setting the Priority channel For only the Dual/Tri-watch:
• Set mode setting 1. Setting duplex • Rotate [DIAL] to select the desired TAG channel to re-
q Push [SET] to enter the Set mode. Hold down [DUP] (LOW) for 1 second once or twice to se- r Rotate [DIAL] to select the channel to set as the Call or ceive.
w Push [SET] or [MONI] to select a desired item. lect minus duplex or plus duplex. Priority channel. u To stop the watch, push [M/CALL].
e Rotate [DIAL] to select an option or value. t Push any key other than [SET], [MONI] or [BANK], to
DIGITAL PRIO AO BUSY
r Push any key other than [SET] or [MONI], to save and MUTE
NAR save the setting and exit the Marine Set mode.
MID
exit the Set mode. LOW
LOCK ANM DUP T-SCAN PRIO SCAN
SET MONI LOW TONE M/CALL V/ MHz
• Reverse mode ond to enter the Initial Set mode. SAIL One 5-second blast followed by two 5 sec. ±1 Sailing vessel underway, fishing vessel
1 sec.
Turn the Reverse Duplex w Push [SET] or [MONI] to select the desired item. "FOG-SA" 1-second blasts (each separated by 2 (underway or anchored), vessel not under
command, a vessel restricted in her ability
SET MONI
function ON or OFF e Rotate [DIAL] to select the option or value. seconds) every 120 seconds.
2 sec. 120 sec. to maneuver (underway or at anchor), or a
r Push [ ] to save and exit the initial Set mode. vessel towing or pushing another ahead.
• Tuning step Vessel under tow (manned).
TOW One 5-second blast followed by three 5 sec. ±1 1 sec.
Set the VFO tuning step. Initial Set mode items : [MONI] "FOG-TO" 1-second blasts (each separated by
: [SET] 2-seconds) every 120 seconds.
SET MONI
• Key-touch beep 2 sec. 120 sec.
DIGITAL
• Auto power OFF w Hold down [OPT] (BANK) for 1 second, to enter the Ma-
rine Set mode.
D Setting the Public Address function
DIGITAL
• Display dimmer MUTE
Automatically turn
e Push [SET] or [MONI] to select the desired item.
NAR
MID
LOW the transceiver’s power OFF.
q Push [M/CALL] one or more times to select the marine
LOCK ANM DUP T-SCAN
D Marine Set mode items e Push [SET] or [MONI] until “PVL” appears.
LOCK ANM DUP T-SCAN
SET MONI LOW TONE
Set the Auto Dimmer brightness.
SET MONI
Marine Set mode items : [MONI]
r Rotate [DIAL] to set the output level to between 1 (mini-
• Squelch delay mum) and 32 (maximum).
: [SET]
• Display color MUTE
NAR
DIGITAL
Set the squelch delay to “S” (Short) or • Priority channel t Push any key other than [SET], [MONI] or [BANK], to
MID
LOW
LOCK ANM DUP T-SCAN “L” (Long). MUTE
DIGITAL AO BUSY Set the Priority channel. save the setting and exit the Marine Set mode.
Select the display backlight color. SET MONI LOW TONE
NAR
MID
LOW
SET MONI
• Squelch type
• Display contrast
MUTE
NAR
DIGITAL Set the squelch type to “OFF” (Noise squelch), • Call channel q Hold down [PA] (MONI) for 1 second, to turn ON the
MID “SS” (S-meter Squelch) or DIGITAL AO BUSY
Set the Call channel. Public Address function.
Adjust the LCD contrast. LOW MUTE
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE “AT” (Squelch Attenuator). NAR
MID
LOW DIGITAL AO BUSY
SET MONI
LOCK ANM DUP T-SCAN PRIO SCAN MUTE
SET MONI NAR
MID
LOW
DIGITAL
• Skip channel
Turn the TX inhibit function ON or OFF.
MUTE
NAR DIGITAL AO BUSY Turn the channel skip setting ON • While the Public Address function is ON, only [SET],
MID
Turn the Tone Burst function ON or OFF. MUTE
NAR
SET MONI
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
MID
LOW
LOCK ANM DUP T-SCAN PRIO SCAN
normal voice level.
SET MONI
• “PA ON” blinks, while holding down [PTT].
• Bank setting †
• Display type
• Foghorn function e Hold down [PA] (MONI) for 1 second again, to turn OFF
Assign the desired memory MUTE
NAR
DIGITAL
Set the display type MUTE
DIGITAL AO BUSY Set the Foghorn pattern to the Public Address function.
NAR
and scan edge channels. MID
LOW
LOCK ANM DUP T-SCAN
while in the memory mode. MID
LOW
Underway (“WA”), Stop (“ST”),
SET MONI SET MONI LOW TONE LOCK ANM DUP T-SCAN PRIO SCAN
■ AF output selections
SET MONI Sail (“SA”), Tow (“TO”) or OFF (“OF”).
• Bank link function† • Voltage display • Foghorn frequency
Assign the desired banks DIGITAL DIGITAL AO BUSY Set the Foghorn frequency to between The IC-2300H has three AF output selections. Select the
MUTE
NAR Turn the Voltage Display MUTE
SET MONI
for a continuous banks scan. MID
LOW
LOCK ANM DUP T-SCAN function ON or OFF.
NAR
MID
LOW
200 and 850 Hz, in 10 Hz steps. output that suits your operating style.
q Push [M/CALL] one or more times to select the marine
LOCK ANM DUP T-SCAN PRIO SCAN
SET MONI LOW TONE
SET MONI
SET MONI
and receive passband.
MUTE
NAR
MID to between 1 (min) and 32 (max). rine Set mode.
e Push [SET] or [MONI] until “RSP” appears.
LOW
LOCK ANM DUP T-SCAN PRIO SCAN
SET MONI
A-6966H-4EX
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Printed in Japan
Printed on recycled paper with soy ink. © 2013 Icom Inc.