Professional Documents
Culture Documents
6190.1823.02 - 01
Operating Manual
The documentation describes the following software:
xx = software variant
©
12/2017 Rohde & Schwarz GmbH & Co. KG
Email: info@rohde-schwarz.com
Internet: http://www.rohde-schwarz.com
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol, e.g. R&S®ZS4400 is indicated as
R&S ZS4400.
R&S ZS4400 Abbreviations
Abbreviations
addr, ADDR address
A ampere
C control unit
CU control unit
ENT enter
FW firmware
IP Internet Protocol
MHz megahertz
ms millisecond
OS operating system
PC personal computer
R radio
s second
SW software
XT VHF/UHF transceiver
Table of Contents
1 Introduction............................................................................................ 1.1
1.1 Preface............................................................................................................................ 1.1
1.1.1 Features .......................................................................................................................... 1.1
1.1.2 Requirements .................................................................................................................. 1.2
1.2 Required Skills............................................................................................................... 1.2
2 Installation.............................................................................................. 2.1
2.1 Installing the Service & Maintenance Tool R&S ZS4400 ........................................... 2.1
2.2 Directory Structure and Files ..................................................................................... 2.10
2.3 Uninstallation............................................................................................................... 2.11
4 Operation................................................................................................ 4.1
4.1 General ........................................................................................................................... 4.1
4.2 Starting a Session ......................................................................................................... 4.1
4.2.1 Ethernet Connection........................................................................................................ 4.1
4.2.2 Running the Radio........................................................................................................... 4.3
4.2.3 Starting the Software ....................................................................................................... 4.4
4.2.4 Communications Connection........................................................................................... 4.4
List of Figures
Figure 2.1 Agreement for R&S ZS4400 ...................................................................................................... 2.2
Figure 2.2 Installation directory................................................................................................................... 2.3
Figure 2.3 User account control.................................................................................................................. 2.4
Figure 2.4 Welcome to WinPcap setup (example)...................................................................................... 2.5
Figure 2.5 Agreement for WinPcap ............................................................................................................ 2.6
Figure 2.6 Installation options for WinPcap ................................................................................................ 2.7
Figure 2.7 Completing WinPcap installation ............................................................................................... 2.8
Figure 2.8 Completing R&S ZS4400 installation ........................................................................................ 2.9
Figure 2.9 Modify/uninstall dialog ............................................................................................................. 2.11
Figure 2.10 Modify setup dialog.................................................................................................................. 2.12
Figure 2.11 Uninstall completed ................................................................................................................. 2.12
Figure 3.1 Service & Maintenance Tool GUI start-up screen (sample data) .............................................. 3.1
Figure 3.2 Screen layout (sample data)...................................................................................................... 3.2
Figure 3.3 File pull-down menu .................................................................................................................. 3.3
Figure 3.4 Customize directories ................................................................................................................ 3.4
Figure 3.5 Define own IP and send IP to R&S M3SR radio........................................................................ 3.5
Figure 3.6 "TCP/IP Timeout" dialog ............................................................................................................ 3.6
Figure 3.7 "Edit" pull-down menu................................................................................................................ 3.7
Figure 3.8 "View" pull-down menu .............................................................................................................. 3.8
Figure 3.9 "Applications" pull-down menu .................................................................................................. 3.9
Figure 3.10 "Update 32" pull-down menu ................................................................................................... 3.10
Figure 3.11 "Help" pull-down menu ............................................................................................................ 3.11
Figure 3.12 "About ZS4400" window (sample data) ................................................................................... 3.11
Figure 3.13 Tool not connected to a device................................................................................................ 3.13
Figure 3.14 Tool connected to a device...................................................................................................... 3.14
Figure 3.15 Toolbar mouse-over information.............................................................................................. 3.14
Figure 4.1 Direct connection of radio and computer ................................................................................... 4.2
Figure 4.2 Connecting radio and computer via hub / switch ....................................................................... 4.3
Figure 4.3 Service & Maintenance Tool start-up (sample data).................................................................. 4.5
Figure 4.4 Device type selected (sample data) .......................................................................................... 4.6
Figure 4.5 "Add new device" dialog (sample data) ..................................................................................... 4.7
Figure 4.6 Connected to an R&S M3SR radio (sample data) ..................................................................... 4.8
Figure 4.7 Connected to an R&S M3SR Control Unit (sample data) .......................................................... 4.9
Figure 4.8 PIN entry request..................................................................................................................... 4.10
Figure 4.9 Device’s inventory list (sample data) ....................................................................................... 4.12
Figure 4.10 Header data (sample data) ...................................................................................................... 4.13
Figure 4.11 Edit header data (sample data) ............................................................................................... 4.14
Figure 4.12 Errorlog (sample data) ............................................................................................................. 4.15
List of Tables
Table 1.1 Features of the Service & Maintenance Tool R&S ZS4400....................................................... 1.1
Table 2.1 Files installed in the working directory ..................................................................................... 2.10
Table 2.2 Directories created when starting the application for the first time .......................................... 2.11
Table 3.1 "File" menu ................................................................................................................................ 3.3
Table 3.2 "Select own IP" options.............................................................................................................. 3.5
Table 3.3 "Edit" menu ................................................................................................................................ 3.7
Table 3.4 "View" menu .............................................................................................................................. 3.8
Table 3.5 "Applications" menu................................................................................................................... 3.9
Table 3.6 "Help" Menu............................................................................................................................. 3.11
Table 3.7 Toolbar buttons........................................................................................................................ 3.12
Table 4.1 Dependency of software upload on software release and part number of Receiver Module
R&S ET4400............................................................................................................................ 4.20
Index
"Applications" menu ............................................................3.9 M
"Clear PINs" ......................................................................4.10
"Edit" menu .........................................................................3.7 Main view ............................................................................3.1
"Errorlog" ...........................................................................4.15 Menu bar ............................................................................3.3
"File" menu ..........................................................................3.3
N
"Help" menu ......................................................................3.11
"Inventory" .........................................................................4.12 New device .........................................................................4.6
"Load Options" ..................................................................4.11
"Remove from list" ............................................................4.10 O
"Save Options" ..................................................................4.11
Operation ............................................................................4.1
"Update 32" menu .............................................................3.10
"View" menu ........................................................................3.8 P
A Preface ...............................................................................1.1
Abbreviations ..........................................................................i R
C Required skills ....................................................................1.2
Requirements .....................................................................1.2
Communications connection ...............................................4.4
Running a session ..............................................................4.5
Connect to a device ............................................................4.8
Running the radio ...............................................................4.3
D S
Description ..........................................................................3.1
Security, PINs .....................................................................4.9
Directory structure and files ..............................................2.10
Software update ...............................................................4.18
E Software upload ................................................................4.20
Starting a session ...............................................................4.1
Ethernet connection ............................................................4.1 Starting the software ...........................................................4.4
Status bBar .......................................................................3.13
F
T
Features ..............................................................................1.1
Toolbar .............................................................................3.12
G
U
General ...............................................................................4.1
Uninstall ............................................................................2.11
I
Installation ...........................................................................2.1
Introduction .........................................................................1.1
1 Introduction
1.1 Preface
This documentation describes the Rohde & Schwarz Service & Maintenance Tool
R&S ZS4400, Basic Edition software to give the user an understanding of its functions and
to how to run it. The user will be enabled to handle data flow between the computer running
the R&S ZS4400 and R&S M3SR Series 4400 devices.
The purpose of this documentation is not to teach capabilities in R&S M3SR Series 4400 de-
vice configuration techniques. The user is supposed to have that kind of knowledge when
modifying devices' configurations.
1.1.1 Features
The Service & Maintenance Tool R&S ZS4400 provides a Windows graphical user interface
(GUI) for a personal or laptop computer to facilitate the task of transferring device data to and
from R&S M3SR Series 4400 devices or performing software updates.
A special feature of the Maintenance Edition, which may be acquired separately, is the pos-
sibility to read configuration parameters and defined presets from a radio, store them in files
and upload them to similar radios producing configuration and presets clones at any time.
Table 1.1 Features of the Service & Maintenance Tool R&S ZS4400
• Read and clear errorlogs • Read, store and duplicate configuration parameters
• Read inventory data • Read, store and duplicate preset pages
• Modify device headers
• Update software
• Transmit software option codes
Before sending uploadable binaries to the connected device, the Service & Maintenance
Tool starts the Rohde & Schwarz software tool ADFCONVERT to convert them to the "Ad-
vanced Data File (ADF)" format.
To upload software into R&S M3SR Series 4400 devices, the Service & Maintenance Tool
relies on the Rohde & Schwarz software tool UPDATE32.
1.1.2 Requirements
The minimum hardware and software requirements of the Service & Maintenance Tool soft-
ware are:
The user of the Service & Maintenance Tool R&S ZS4400 is required to have state of
the art knowledge of the Microsoft Windows operating system including basic knowl-
edge of network technology, e.g. TCP/IP.
Profound knowledge of the R&S M3SR Series 4400 devices and the handled data is
mandatory to avoid malfunctions.
2 Installation
The Service & Maintenance Tool R&S ZS4400 is installed on a computer with the aid of an
installation routine.
The Rohde & Schwarz software tools UPDATE32 (data transfer program) and ADFCON-
VERT (binary to ADF converter) will be installed together with the Service & Maintenance
Tool R&S ZS4400 to be employed by it.
This section describes the installation routine for Windows 10 as an example based
on the corresponding screenshots. For other versions of Windows, proceed analo-
gously.
ICN-4F-D-230010-R-D0894-10050-A-01-1
ICN-4F-D-230010-R-D0894-10051-A-01-1
The Service & Maintenance Tool files plus the UPDATE32 and ADFCONVERT files will
be copied to that directory.
6. In the "User Account Control" dialog, click "Yes".
ICN-4F-D-230010-R-D0894-10083-A-01-1
If no installation of WinPcap 4.1.x is found on the target machine, the WinPcap setup is
started.
ICN-4F-D-230010-R-D0894-10052-A-01-1
7. Click the "NEXT" button to start the installation routine for the WinPcap component.
ICN-4F-D-230010-R-D0894-10053-A-01-1
ICN-4F-D-230010-R-D0894-10077-A-01-1
ICN-4F-D-230010-R-D0894-10078-A-01-1
ICN-4F-D-230010-R-D0894-10079-A-01-1
12. Click the "Launch" button to finish and directly start the application,
or click "Close" if you wish to start it later.
The installation routine inserts a "ZS4400" entry in the "Start" menu. It does not gen-
erate a desktop icon.
File Contents
When the R&S ZS4400 is run for the first time, it generates one directory for data storage
and one configuration file. The storage location of these items depends on the rights level of
the user running the application. The directories and files are created within the "ZS4400"
installation directory for administrative users (admins). For normal users (non-admins) with-
out write access to the "ZS4400" installation directory, the folder and file creation is redirect-
ed by Windows to:
"C:\Users\USERNAME\AppData\Local\VirtualStorage\Program Files (x86)\ZS4400"
If you want to share R&S ZS4400 configuration and radio data with other users, copy this
directory to a location accessible to all users. If another user wants to use this configuration
data, the directory must be copied to the following folder of this user before starting up the
application:
"C:\Users\USERNAME\AppData\Local\VirtualStorage\Program Files (x86)\"
Temporary files are generated in "C:\temp" when preparing a download to the connected de-
vice.
Table 2.2 Directories created when starting the application for the first time
Directory Contents
.\temp Temporary files that are generated in preparing a download to the con-
nected device.
M3SR Devicelist.cfg Common R&S ZS4400 application configuration values and configured
device connections
2.3 Uninstallation
1. Open the Windows settings dialog to modify or remove programs.
ICN-4F-D-230010-R-D0894-10080-A-01-1
ICN-4F-D-230010-R-D0894-10081-A-01-1
ICN-4F-D-230010-R-D0894-10082-A-01-1
3 Description
3.1 General
This chapter describes the Service & Maintenance Tool R&S ZS4400 and its options. For op-
eration, refer to sect. 4 Operation.
Figure 3.1 Service & Maintenance Tool GUI start-up screen (sample data)
ICN-4F-A-230010-R-D0894-10055-A-01-1
2
3
ICN-4F-A-230010-R-D0894-10056-A-01-1
1 Selection tree
2 Menu bar
3 Toolbar
4 Data display
5 Status bar
The menu bar offers pull-down menus to give access to all functions (”Menu Bar” on p. 3.3).
Some frequently used options are accessible via buttons in the toolbar below it (”Toolbar” on
p. 3.12).
The selection tree shows information read either from the harddisk or the connected device,
depending on context. The data display visualizes hardware and software data read from the
item selected in the selection tree.
The status bar (”Status Bar” on p. 3.13) at the bottom of the screen gives information about
the current status of the tool, e.g. whether a connection to the R&S M3SR Series 4400 device
has been established. In addition, it may deliver information relating to the option below the
mouse pointer.
ICN-4F-A-230010-R-D0894-10057-A-01-1
Menu Function
"Save As Text" Opens a Windows "Save as..." dialog to store the contents of the data
display as text in a file.
"Print... Ctrl+P" Opens a Windows "Print" dialog to print the contents of the data display.
ICN-4F-D-230010-R-D0894-10058-A-01-1
The "R&S Software Package" entry must point to a directory that contains a software
package fitting the configuration of the connected R&S M3SR device.
The referenced file "structure.txt" contains the configuration data of the software package
(e.g. R&S DS4400A), which must match the connected device (e.g. R&S XT4410A) for soft-
ware updates and header editing. Any disregard may cause malfunctioning and even destroy
the radio!
ICN-4F-A-230010-R-D0894-10059-A-01-1
R&S M3SR SECOS radios, models 85 to 90 have a CPLAT software version that stores the
IP address of the servicing computer and will not connect to a different address. With the op-
tion "Own IP", a certain IP address may be transferred to the connected radio.
Option Function
"Use main IP address from PC" Detected IP address of the standard built-in networking card.
"Use this IP address" If the radio is connected to a secondary networking card, the IP address
has to be entered manually.
ICN-4F-A-230010-R-D0894-10060-A-01-1
When a slow TCP/IP connection is used to link an R&S M3SR radio to the PC where the
R&S ZS4400 is running, the standard timeout times may be too short for communication. In
this case, use this dialog to increase the relevant timeout time.
ICN-4F-A-230010-R-D0894-10061-A-01-1
Menu Function
"Copy Ctrl+C" The contents of the data display is copied to the Windows clipboard.
ICN-4F-A-230010-R-D0894-10062-A-01-1
Menu Function
"Status Bar" Toggles the display of the status bar (”Status Bar” on p. 3.13).
ICN-4F-A-230010-R-D0894-10063-A-01-1
Menu Function
"Connect" The R&S ZS4400 tries to connect to a selected device. The following ap-
plications in this menu list require a successfully established connection.
Except for the "Connect" application, the options are available only if a device is connected.
ICN-4F-A-230010-R-D0894-10064-A-01-1
The standard R&S M3SR SW update method requires that both radio and control unit con-
tain executable software where an inventory can be taken to determine which software pack-
ages are to be loaded. If there is no executable software installed on the radio or control unit,
this menu option can be used to load a radio or control unit software without prior checking
and matching.
Afterwards, it is absolutely necessary to carry out the standard software update procedure
to ensure consistency of the loaded software.
ICN-4F-A-230010-R-D0894-10065-A-01-1
Menu Function
"About ZS4400..." Displays a window with information about R&S ZS4400 (Figure 3.12).
ICN-4F-A-230010-R-D0894-10066-A-01-1
3.4 Toolbar
Except for the "Connect" button, the buttons are available only if there is a connection
to a device.
Icon Function
The contents of the data display are sent to the Windows printer.
Same option as "Print... Ctrl+P" in the "File" menu (”"File" Menu” on p.
3.3).
The contents of the data display are copied to the Windows clipboard for
pasting into another software.
Same option as "Copy Ctrl+C" in the "Edit" menu (”"Edit" Menu” on p.
3.6).
ICN-4F-A-230010-R-D0894-10067-A-01-1
At the right, the status bar indicates the connection status of the R&S ZS4400.
The green circle indicates a successful connection. It is followed by the connected TCP ad-
dress.
ICN-4F-A-230010-R-D0894-10068-A-01-1
ICN-4F-A-230010-R-D0894-10069-A-01-1
At the left, the status bar displays the general status or information about the toolbar button
that the mouse is over.
4 Operation
4.1 General
This chapter describes a typical operating procedure of the R&S ZS4400. Operations that
are typical of Microsoft Windows are not explained in detail.
Before starting the R&S ZS4400, the computer has to be electrically connected to an
R&S M3SR Series 4400 device.
TCP/IP services must be installed on the computer running the R&S ZS4400.
The R&S M3SR radio can be connected to a computer through two Ethernet ports. The
"SERVICE" connector is on the front panel, the "X20" connector on the rear. They differ in
pin configuration, so different cables must be used. The "X20" port is designed for network
use to be connected to a hub or switch (Figure 4.2), so a crossover LAN cable is needed for
a direct PC link. The "Service" port may be connected to the computer via common Network
LAN cable.
M3SR X20
Crossover
Ethernet Computer
Radio (rear) LAN-cable
M3SR SERVICE
Network
Ethernet Computer
Radio (front) LAN-cable
ICN-4F-A-230010-R-D0894-11001-A-01-1
M3SR X20
Network Hub / Network
Ethernet Computer
L AN-cable LAN-cable
Radio (rear) Switch
M3SR SERVICE
Crossover Hub / Network
Ethernet Computer
LAN-cable LAN-cable
Radio (front) Switch
M3SR SERVICE
Network Hub / Crossover
Ethernet Computer
LAN-cable LAN-cable
Radio (front) Switch
ICN-4F-A-230010-R-D0894-11002-A-01-1
The hub or switch may be part of a computer network. Other devices like R&S M3SR Series
4400 radios may be connected to the network and addressed by the computer running the
R&S ZS4400, although not simultaneously.
If the computer is part of a LAN, connect the R&S M3SR Series 4400 device to a hub
of that network. The device and the computer must be in the same subnet (for SW re-
leases < 10, see menus 436, 835 and 836 in the relevant documentation; for SW releas-
es 10, see menus 1165 and 1330).
If the connected and selected Series R&S M3SR Series 4400 device is in "Fixed Ses-
sion" mode, only data monitoring is possible.
To upload configurations or options, the R&S ZS4400 tries to set the receiving device into
"Radio Session" mode (for SW releases < 10) or "Offline" mode (for SW relaseses 10) for
that period of time. If this is not possible, the R&S ZS4400 displays a warning message.
During data download to a radio, it switches to "Radio Session"/"Offline" mode, and all other
radio operations are suspended.
To start the R&S ZS4400, go to "Start / Programs / ZS4400" and click the "ZS4400" entry.
ICN-4F-A-230010-R-D0894-10055-A-01-1
There is no device selected and therefore no connection present. A connection may be es-
tablished to a new (”New Device” on p. 4.6) or an already defined (”Connect to a Device” on
p. 4.8) device.
If a new device has to be tested or configured, select a device type ("M3SR Radios" or
"M3SR Control Units") in the selection display by clicking it with the mouse.
ICN-4F-A-230010-R-D0894-10004-A-01-1
Click the "Add Device" button, enter the unique logical address and the device IP address in
the "Add new device" form and confirm with "OK".
ICN-4F-A-230010-R-D0894-10005-A-01-1
Any error causes a message to pop up and returns you to the start-up screen
(Figure 4.3).
Click a device number in the selection display. The R&S ZS4400 tries to establish a network
connection to the chosen device.
ICN-4F-A-230010-R-D0894-10007-A-01-1
Any error causes a message to pop up and returns you to the start-up screen
(Figure 4.3).
If connection has succeeded, the Service & Maintenance Tool displays a "connected to:
TCP..." message in the status bar, preceded by a green circle (Figure 4.6). The data display
shows current data read from the device. The "State" entry may show varying information.
Usually, it reads "Connected" for regular operations. A sample error message for "State"
could be "No radio" if the connected device in the above sample at the logical address "46"
were an R&S M3SR Control Unit.
Any error in the execution of the following applications causes a message to pop up
and returns you to the connect screen (Figure 4.6).
If the selected device is a control unit, the buttons "Clear PINs" and "Load Options" are not
available due to the different design.
ICN-4F-A-230010-R-D0894-10008-A-01-1
For some actions, R&S M3SR Series 4400 radios require a PIN to legitimize the user action.
In such a case, the R&S ZS4400 tries the following in the given order:
ICN-4F-A-230010-R-D0894-10009-A-01-1
When the checkbox "save PIN" is ticked, the R&S ZS4400 adds the entered code to the
stored PIN list after the "OK" button was clicked. The list collects device numbers and their
associated PINs until it is cleared (”"Clear PINs"” on p. 4.10).
With the next request from the radio, the R&S ZS4400 sends the saved PIN automatically.
With this button, the stored PINs are deleted from the computer. There is no other way to
change stored PINs except by first deleting them and then entering the new values.
Clearing the PINs from the computer does not affect the PINs stored in the radios.
This button removes the selected device from the list in the selection display with its logical
address number and the associated data like the TCP/IP address.
To activate built-in but not accessible functions of an R&S M3SR Series 4400 radio, corre-
sponding software option control data has to be transferred into it. This data is contained in
software option control files that can be acquired from Rohde & Schwarz.
"Load Options" will load radio software option control data (*.SOC = "Software Option Con-
trol") from disk to transfer to the radio.
Clicking the button opens the directory where the file "structure.txt" (see sect. 3 Description)
is located. Navigate to the CD-ROM drive "X" in the window "Open file" dialog to select the
desired SOC file.
If the serial number of the radio does not correspond to the serial number the SOC file
was acquired for, the radio is reset to its default status and loses all installed software
options.
Downloading software options to the radio relies on having a "Radio Session" (for SW
releases < 10) or being in "Offline" mode (for SW releases 10).
The control unit shall have a "Monitor Session" only; no other client shall be connected to the
radio.
Clicking this button downloads the Software Options Control data from the radio, so it may
be saved to a file.
4.3.3 "Inventory"
ICN-4F-A-230010-R-D0894-10010-A-01-1
For further information about header data, refer to the device’s documentation.
The connected device’s TCP address is permanently visible in the status bar.
Following a hardware change in the device, e.g. after adding a module or a software option
(”"Load Options"” on p. 4.11), it may be necessary to modify the hardware device header in
the device.
For this purpose, first select the device header in the selection display.
The R&S software or hardware update package includes the necessary information
for the entry changes.
ICN-4F-A-230010-R-D0894-10011-A-02-1
The device header data then can be edited in the "Edit Header" dialog. Open it by clicking
the "Edit" button.
Before clicking the "Send to device" button, check if the entries are correct. Incorrect
entries may cause malfunctioning or even destroy the radio.
A header with invalid content cannot be edited any more. In this case, create a new header
using the button "New Header".
Only the header of the device and the modules HWMod KR4400 Basic and HWMod GP4400
Protec can be edited.
ICN-4F-A-230010-R-D0894-10012-A-01-1
"Send to device" starts the software upload process to transmit the modified data to the con-
nected device (”Software Upload” on p. 4.20). After the upload has finished, the
R&S ZS4400 returns to the "connect" mode and automatically polls the network until recon-
necting to the device has succeeded (”Connect to a Device” on p. 4.8).
4.3.4 "Errorlog"
This function reads the errorlog from the connected device and displays it.
ICN-4F-A-230010-R-D0894-10014-A-01-1
Clicking the "Clear Errorlog" button erases the errorlog in the connected device.
ICN-4F-A-230010-R-D0894-10015-A-01-1
To get a complete detailed view of the errorlog, tick the "Show Details" checkbox
(Figure 4.14). Clicking a specific error in the selection display shows the details of that par-
ticular error (Figure 4.15).
ICN-4F-C-230010-R-D0894-10016-A-01-1
ICN-4F-C-230010-R-D0894-10017-A-01-1
The software package matching the device hardware must be in the folder defined in the di-
rectory listing ("File / Directories") in the "R&S Software Package" entry.
The R&S ZS4400 reads the "structure.txt" file from the "R&S Software Package" directory to
ensure that the software package is consistent with the hardware configuration of the con-
nected device. In addition, it contains version data, which is displayed on screen. If the soft-
ware versions of the connected device and the software package are not identical for any
module, the lower number is displayed in red (radio sample: Figure 4.16; control unit sample:
Figure 4.17).
The update overwrites the software of all device modules, irrespective of any version
differences. Therefore, it is possible to overwrite a newer version with an older one.
Different versions are marked by the lower version being displayed in red.
Exception: If the firmware ACPCB EQI is not loaded, the SW/FW name is displayed in red.
The reason is that the radio contains the older firmware ACPCB AQI. In such a case, we rec-
ommend that you contact the nearest Rohde & Schwarz representative. The download of the
other device modules is not concerned by this consistency check.
The consistency check is performed for both parts (radio and control unit) (Figure 4.17).
ICN-4F-A-230010-R-D0894-10018-A-01-1
ICN-4F-A-230010-R-D0894-10019-A-01-1
Clicking the "Start Update" button starts the software upload (”Software Upload” on p. 4.20).
Table 4.1 Dependency of software upload on software release and part number of Receiver Module
R&S ET4400
15 6102.7001.02
15 6102.7018.02 x
15 6102.7018.03 x
16 6102.7001.02 x
16 6102.7018.02
16 6102.7018.03 x
17 6102.7001.02
17 6102.7018.02
17 6102.7018.03
x • Error message "Selected software package xxx. It does not work with this radio yyy. Download
is not possible" comes up when starting the upload .
xxx, yyy: variable
• Update tool does not start.
• Upload process is aborted.
• Radio remains in its previous state.
1. Click the "Start Update" button for a software update or the "Send to device" button for
a device header update to start the UPDATE32 software.
ICN-4F-A-230010-R-D0894-10020-A-01-1
The "New Network Adapter" window (Figure 4.18) comes up only when R&S ZS4400
is installed the very first time.
2. If the "New Network Adapter" window comes up, click the "OK" button.
3. Select "Ethernet Adapter" in the "Config" menu.
4. Select the desired network adapter.
ICN-4F-A-230010-R-D0894-10021-A-01-1
ICN-4F-A-230010-R-D0894-10029-A-01-1
After the radio within the LAN network has been selected for which the software
update is to be performed, be absolutely sure to press the Reset key on this radio
only. Any disregard may cause malfunctioning or even destroy the radio/control
unit! If the display shows more than one MAC address (Figure 4.21), break off the
update procedure immediately.
ICN-4F-A-230010-R-D0894-10030-A-01-1
ICN-4F-A-230010-R-D0894-10031-A-01-1
After a few minutes, the update is completed (Figure 4.23). The update should take less
than 10 minutes.
9. Click the "OK" button to close the display.
ICN-4F-B-230010-R-D0894-10032-A-01-1
While the UPDATE32 is running, the R&S ZS4400 remains in a passive wait mode.