Professional Documents
Culture Documents
Manual de Update de Firmware Futaba 14SG Fx22 Update v9
Manual de Update de Firmware Futaba 14SG Fx22 Update v9
① Push to open.
2. Insert the 'formatted" SD card into a card reader in your
③ Battery
y cover will
ill ope
open downward.
n do
d
downwa
wnward ④ SD card is inserted in a slot
②Slide in the direction of the
arrow on the battery cover.
by direction of a figure. PC.
*It is releasable if a card is pushed once again.
3. Please run "T14sgUpdate.exe".
FX-22:
SD card slot
*Don't
*D
Don mistake the
b
both sides/ the
direction of
SD card.
k SD card
② It inserts until it locks d into
i t SD
S card slot.
① A side cover is opened.
*It is releasable if a card is pushed once again.
Update
3. Please select "YES" and touch
RTN .
T14SG:
HOME/EXIT U.MENU/MON.
button button
FX-22:
HOME/EXIT U.MENU/MON.
button button
[Installing procedure]
1. Making of card for installing speech data
1. Please unzip the zipped file. The following files will be
created.
(QJOLVK9HUVLRQ
؞7VJ,QVWDOO6RXQG(QJH[H
؞7VJ8SGDWHGDW
؞76*B,167$//B6281'GDW
؞7VJ6SHHFK(QJELQ
؞7VJ6SHHFK(QJELQ
؞7VJ6SHHFK(QJELQ
*HUPDQ9HUVLRQ 2. Install speech data of T14SG/FX-22
؞7VJ,QVWDOO6RXQG(QJH[H 1. Please insert the SD card which includes the installing
؞7VJ8SGDWHGDW speech data.
؞76*B,167$//B6281'GDW 2. Push the HOME/EXIT button.
؞7VJ6SHHFK*HUELQ
؞7VJ6SHHFK*HUELQ
3. Still holding the HOME/EXIT button, power on the
؞7VJ6SHHFK*HUELQ
transmitter.
-DSDQHVH9HUVLRQ INSTALLSOUND
INSTALLING
؞7VJ6SHHFK-SQELQ
for three seconds. The speech
data begins to install.
2. Install the already formatted SD card into your PC's
card reader. 6 . A f t e r a b o u t 16 s e c o n d s , INSTALLSOUND
INSTALLSOUND
7. The uploading may appear to INSTALLING
progress slowly.
COMPLETED
minutes.(About. 2 min.)
And, COMPLETED is displayed.
Please turn off the power.
4. Select the drive that your card reader is assigned to in (Don't turn off the power before COMPLETED is
your PC. Click "OK". displayed.)
Update
WRITE operating is
◆ :KHQWKHWRITERSHUDWLRQLVVXFFHVVWKHPHVVDJH To [RX] of KS-01
writing CH setting to
"COMPLETED"LVVKRZQ:KHQWKHWRITERSHUDWLRQLV
KS-01.
IDLOXUHWKHPHVVDJH"FAILED"LVVKRZQ OUT
IN
LED
RX
OUT LED
RECALL operation is IN RX
reading CH setting from
KS-01.
KS-01
LED
)87$%$&25325$7,21
6V Direct
RDNNDQGDNDMLFKR).DQGDNDMLFKR&KL\RGDNX7RN\R-DSDQ7(/)$;
)87$%$&25325$7,21